1. To Check the Number of HSDPA User allocated per cell: LST UCELLCAC-----in RNC end 2. To Check the SCTPLNK & SAAlLNK: LST UIUBCP: 3. LST OP ADD OP (For Creating Account in RNC/BSc for Local login during M2000 Connecti vity down) 4 IRAT:3G to 2G handover Network reselection :2G to 3G handover.
5. LST Unode---To get node-B all info in RNC end
6. DSP UCELL---To check the status of Node-B cell(Result---Cell is Setup and ena bled) DSP UCELLCHK---to check traffic in RNC end BLK UCELL---to Block cell in RNC DEA UCELL--To Deactivate Cell in RNC. ACT UCELL--To Activate Cell in RNC UBL UCELL----To UBlock Ucell in RNC BLK Unode-B----To Block Unode-B in RNC UBL Unode-B----To Unblock Unode-B in RNC RST Unode-B----to Reset Unode-B in RNC PING IP--------To ping the Node-B Service from RNC TRC IPADDR------To check where we are getting drop in RNC LST UCELL------To get information about the Cell like PSC,Frequency,Transmitting Power,LAC,SAC,RAC in RNC LST UPCPICH------To check pilot channel power MOD UPCPICHPWR----To Change Pilot Channel Power in RNC. LST UINTRAFREQNCELL------Use this command to query the intra-frequency neighbori ng cell. ADD UINTRAFREQNCELL---- to add neighbour Cells (IntraFreq)
LST UEXT3GCELL-----------List the information of neighboring RNC cells. ADD ADD ADD dsp LST
UEXT3GCELL----To Add the 3G cells(Other Vendors) as external cells. UEXT2GCELL----To Add the 2g Cells As external Cells U2GNCELL------To add the 2G Neighbour Cells usrnum----Hsdpa Throughput per subrack PHBMAP---To Check the Service Priority
To Change the Node-B Name in RNC: 1.MOD UNODEBNAME 2.MOD ADJNODE To Change the Node-B Name in Node-B end 1.MOD SITE 2.SET NODEBNAME LST DEVIP----To check the RNC Board IP. LST ETHIP----To Check the Ethernet port IP. LST ALMAF----To check the RNC Alarm DSP E1T1---To check the E1T1 of Site in RNC end. LST DSP DSP LST DSP LST LST DSP LST MOD
VER---To check the Software Version of RNC. OMU----To check the OMU Status in RNC. OMUHW---To check the Status of ETH port. License---To check the License file loaded in RNC & Active license. LICUSAGE---To check the feature activated in the License. UCELLHSDPA----To check whether the HSDPA feature is Activated or Not. UCELLHSUPA----To check whether the HSUPA feature is Actiavted or not ELABEL:to Check the item Code of Boards UAC----To Check the LAC & RAC. UCELLLACINFO----To Change LAC,RAc,SAC for Cell.
Node-B REQ FOC hen LST RST RST BLK BLK DSP ADD ADD LST LST MoD LST LST LST MOD LST LST LST ame
CMCTRL----request CM control for an LMT user CMCTRL-----to forcibly obtain the NE Configuration Management (CM) control w the M2000 retains CM control after obtaining it. DEVIP----To Check what are the IP defined in Node-B BRD---to reset the board NODEB---To reset the whole node-B BRD--to block board LOCELL---To block CELL. VSWR----to check VSWR. DEVIP---to add the Devip in Node-B IPRT---- To add the Iproute in node-B. RRU----to Check the RRU Number,RRU work Standard RRUCHAIN----- To Check the Chain Number,WBBP board Subrack no,Slot Number. LOCELL-----to Change the Frequecy number,transmitting power. LOCELL----to check the Local cell id,Cell ID. SEC--to Check the Sector Type RXBRANCH---To check the Attenuation RXBRANCH----To Modify the attenuation. ALMAF-------To check the Alarm in Node-B end. VER-------To check the Software version. NODEBNAME---To check the Correct Configuration file is loaded or not,Nodeb N normally will be the Site Name.
PING---To do ping test in Node-B end. TRACERT---To Check,is there any drop in IP(Useful to check transmission having p roblem) LST IPCLKLNK---To check the IPClock IP address. DSP IPCLKLNK---to Check the Status of IPCLK. LST ALMPort---To check the External Alarm Configuration. SET ALMPort---to Define the External Alarm in Node-B end. SET ENVALMPARA----To define the External Alarm Name. LST ETHPORT -------To check the ETHport Configurtion SET ETHPORT-------To Configure the ETHport DSP TIME-----To check the Current time in Node-B SET TIME----To Set the Correct time DSP LICENSE----To check License is loaded or not. DSP CELLCFG----To check the Scrambling code (PSC) ULD File-------To upload the Log File DSP SFP---to Check the SFP module type & output power
Site Down Alarm NCP,CCP Alarm SCTP,SAALNK. NodeB Unavailable