Modul untuk praktek simulasi jaringan komputer dengan Cisco Packet TracerFull description
Deskripsi lengkap
Modul untuk praktek simulasi jaringan komputer dengan Cisco Packet Tracer
Experiments Using Cisco Packet TracerFull description
QoS Cisco Packet Tracer TutorialFull description
RedesFull description
Descrição completa
packet tracer
Praktek TKJ
Full description
ebook ini menjelaskan tentang konfigurasi VLSM di cisco packet tracer
cisco 3.2.2.4 ccna answersDescripción completa
Topología Malla en Cisco Packet TracerDescripción completa
Deskripsi lengkap
MANEJO DE REDES CISCO PACKET TRACER (PRACTICAS) PRACTICA #3
INFO 6205
Página 1
MANEJO DE REDES
INFO 6205
Página 2
MANEJO DE REDES
INFO 6205
Página 3
MANEJO DE REDES PRACTICA #4 CONFIGURACION R1 Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 18-Jul-07 04:52 by pt_team
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: n
Press RETURN to get started!
Router>enable Router#erase startup-config Erasing the nvram filesystem will remove all configuration files! Continue? [confirm] [OK] Erase of nvram: complete %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram Router#config terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#interface FastEthernet0/0
INFO 6205
Página 4
MANEJO DE REDES R1(config-if)#ip address 172.17.50.1 255.255.255.0 R1(config-if)#no shutdown
R1(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up R1(config-if)#exit R1(config)#interface FastEthernet0/1 R1(config-if)#no ip address R1(config-if)#no shutdown
R1(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up R1(config-if)#exit R1(config)#interface FastEthernet0/1.10 R1(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/1.10, changed state to up R1(config-subif)#encapsulation dot1Q 10 R1(config-subif)#ip address 172.17.10.1 255.255.255.0 R1(config-subif)#exit R1(config)#interface FastEthernet0/1.20 R1(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/1.20, changed state to up R1(config-subif)#encapsulation dot1Q 20 R1(config-subif)#ip address 172.17.20.1 255.255.255.0 R1(config-subif)#exit R1(config)#interface FastEthernet0/1.88 R1(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/1.88, changed state to up
%SYS-5-CONFIG_I: Configured from console by console Destination filename [startup-config]? Building configuration... [OK] R1# CONFIGURACION S1 Cisco Internetwork Operating System Software IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE(fc1) Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 18-May-05 22:31 by jharirba
Press RETURN to get started!
Switch>enable Switch#erase startup-config Erasing the nvram filesystem will remove all configuration files! Continue? [confirm] [OK] Erase of nvram: complete %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
INFO 6205
Página 6
MANEJO DE REDES Switch#config terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname S1 S1(config)#interface FastEthernet0/5 S1(config-if)#switchport mode trunk S1(config-if)#no shutdown S1(config-if)#exit S1(config)#interface FastEthernet0/7 S1(config-if)#switchport access vlan 88 % Access VLAN does not exist. Creating vlan 88 S1(config-if)#switchport mode access S1(config-if)#no shutdown S1(config-if)#exit S1(config)#interface FastEthernet0/11 S1(config-if)#switchport access vlan 10 % Access VLAN does not exist. Creating vlan 10 S1(config-if)#switchport mode access S1(config-if)#no shutdown S1(config-if)#exit S1(config)#interface FastEthernet0/18 S1(config-if)#switchport access vlan 20 % Access VLAN does not exist. Creating vlan 20 S1(config-if)#switchport mode access S1(config-if)#no shutdown S1(config-if)#exit S1(config)# TOPOLOGIA COMPLETA