Service Publication
Diesel Engine 16V4000G20 16V4000G40 16V4000G60 16V4000G80
Operating Instructions M015345/20E
DaimlerChrysler Powersystems Off-Highway
Das Handbuch ist zur Vermeidung von Störungen oder Schäden beim Betrieb zu beachten und daher vom Betreiber dem jeweiligen Wartungs- und Bedienungspersonal zur Verfügung zu stellen. Außerhalb dieses Verwendungszwecks darf das Handbuch ohne unsere vorherige Zustimmung nicht benutzt, vervielfältigt oder Dritten sonstwie zugänglich gemacht werden. Änderungen bleiben vorbehalten. This handbook is provided for use by maintenance and operating personnel in order to avoid malfunctions or damage during operation. Other than for this purpose, the handbook shall not be reproduced, used or disclosed to others without our prior consent. Subject to alterations and amendments.
Le manuel devra être observé en vue d’éviter des incidents ou des endommagements pendant le service. Aussi recommandons-nous à l’exploitant de le mettre à la disposition du personnel chargé de l’entretien et de la conduite. En dehors de cet usage, le manuel ne pourra être utilisé ni reproduit ou rendu accessible de quelque autre manière à des tiers, sans notre consentement préalable. Nous nous réservons le droit d’entreprendre toute modification. El Manual debe tenerse presente para evitar anomalias o daños durante el servicio, y, por dicho motivo, el usuario debe ponerlo a disposición del personal de mantenimiento y de servicio. Fuera de este fin de aplicación, el Manual no se debe utilizar, copiar ni poner en manos de terceros, sin nuestro consentimiento previo. Nos reservamos el derecho de introducir modificaciones. Il manuale va consultato per evitare anomalie o guasti durante il servizio, per cui va messo a disposizione dall’ utente al personale addetto alla manutenzione e alla condotta. Senza nostra approvazione preventiva non è ammesso impiegare il manuale per scopi diversi, riprodurlo o metterlo a disposizione di terzi. Con riserva di modifiche.
Wichtig – Important – Importante Bitte die Karte „Inbetriebnahmemeldung“ abtrennen und ausgefüllt an MTU Friedrichshafen GmbH zurücksenden. Die Informationen der Inbetriebnahmemeldung sind Grundlage für den vertraglich vereinbarten LogistikSupport (Gewährleistung, Ersatzteile etc.). Please complete and return the “Commissioning Note” card below to MTU Friedrichshafen GmbH. The Commissioning Note information serves as a basis for the contractually agreed logistic support (warranty, spare parts, etc.). Veuillez séparer la carte “Signalisation de mise en service“ et la renvoyer à la MTU Friedrichshafen GmbH. Les informations concernant la signalisation de mise en service constituent la base pour l’assistance en exploitation contractuelle (garantie, rechanges, etc.). Rogamos separen la tarjeta “Aviso de puesta en servicio“ y la devuelvan rellenada a MTU Friedrichshafen GmbH. Las informaciones respecto al aviso de puesta en servicio constituyen la base para H el soporte logistíco contractual (garantía, piezas de repuesto, etc.). Staccare “Avviso di messa in servizio” e rispedirlo debitamente compilato alla MTU Friedrichshafen GmbH. Le informazioni ivi registrate sono la base per il supporto logistico contrattuale (garanzia, ricambi, ecc.).
Postcard
MTU Friedrichshafen GmbH Abteilung SCSD 88040 Friedrichshafen GERMANY
Bitte in Blockschrift ausfüllen! Please use block capitals! Prière de remplir en lettres capitales! ¡A rellenar en letras de imprenta! Scrivere in stampatello!
Motornr.: Engine No.: No du moteur: No de motor: Motore N.:
Auftragsnr.: MTU works order No.: No de commande: No de pedido: N. commessa:
Motortyp: Engine model: Type du moteur: Tipo de motor: Motore tipo:
Inbetriebnahmedatum: Date put into operation: Mise en service le: Fecha de puesta en servicio: Messa in servizio il:
Eingebaut in: Installation site: Lieu de montage: Lugar de montaje: Installato:
Schiffstyp / Schiffshersteller: Vessel/type/class / Shipyard: Type du bateau / Constructeur: Tipo de bugue / Constructor: Tipo di Barca / Costruttore:
Endabnehmer/Anschrift: End user‘s address: Adresse du client final: Dirección del cliente final: Indirizzo del cliente finale: Bemerkung: Remarks: Remarques: Observaciones: Commento:
Inbetriebnahmemeldung
Commissioning Note
Notice de mise en service
Aviso de puesta en servicio
Avviso di messa in servizio
Amendment Service! Any changes in contents will be sent to you in the form of an amendment, provided you complete the reverse of this receipt card and return it to us.
Postcard
MTU Friedrichshafen GmbH Department SCT 88040 Friedrichshafen GERMANY
No. Please mark all filed amendments here.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Please use block capitals!
Receipt
Amendment No.
1. 2. 3.
Publication number:
4.
M015345/20E
5. 6.
Name Manufacturer
7. 8. 9.
Department Fax Street Postal box number
10. Telephone
11. 12. 13. 14.
(Postal code) City
15.
Country
16.
Date
Name
!
Safety Instructions Summary
A
Product Summary Engine layout, technical data
C
Operating Instructions Task descriptions
D
Operating Instructions Time schedule and maintenance task chart
E
Troubleshooting Causes, remedies
G
Task Description Inspection and maintenance tasks
K
Preservation Engine preservation
T
Transportation Locking Device Drawing, instructions
?
Keyword Index Alphabetical index of key terms
Safety Instructions
Section Page
! 1
Safety, Accident Prevention and Environmental Protection Instructions These instructions must be read and followed by every person involved in operation, maintenance or transportation of the machinery plant. General In addition to the instructions in this publication, the applicable country-specific legislation and other compulsory regulations regarding accident prevention must be observed. This engine is a state-of-the-art product and conforms with all applicable specifications and regulations. Nevertheless, persons and property may be at risk in the event of • Incorrect use • Operation, maintenance and repair by unqualified personnel • Modifications or conversions • Non-compliance with the Safety Instructions
Correct Use The engine is intended exclusively for the application specified in the contract or upon delivery. Any other use is considered improper use. The manufacturer will accept no liability for any resultant damage. The responsibility is borne by the user alone. Correct use also includes observation of and compliance with the maintenance specifications.
Personnel Requirements Work on the engine must only be carried out by properly qualified personnel. The specified legal minimum age must be respected. Responsibilities of the operating, maintenance and repair personnel must be specified.
Modifications or Conversions Modifications made by the customer to the engine may affect safety. MTU will accept no liability or warranty claims for any damage caused by unauthorised modifications or conversions.
Organisational Measures This publication must be issued to all personnel involved in operation, maintenance, repair or transportation. It must be kept at hand near the engine and accessible to all personnel involved in operation, maintenance, repair or transportation. The personnel must be instructed on engine operation and repair by means of this publication, and in particular the safety instructions must be explained. This is especially important for personnel who work on the engine only on an occasional basis. Such personnel must be given instructions repeatedly.
Spare Parts Only genuine MTU spare parts must be used to replace components or assemblies. In event of any damage caused by the use of other spare parts, no liability or warranty claims vis-à-vis the engine manufacturer will be accepted.
Working Clothes and Protective Equipment Wear proper work clothing for all work. Depending on the kind of work, use additional protective equipment, e.g. protective goggles, protective gloves, protective helmet, apron. Work clothing must be tight-fitting so that it does not catch on rotating or projecting components. Do not wear jewellery (e.g. rings, chains, etc.).
15345/20 E 00–05
Section Page
! 2
Safety Instructions
Transportation Lift the engine only with the lifting eyes provided. Use only the transport and lifting equipment approved by MTU. Take note of the engine centre of gravity. The engine must only be transported in installation position. In the case of special packaging with aluminium foil, suspend the engine on the lifting eyes of the bearing pedestal or transport with equipment suitable for heavy loads (forklift truck). Prior to transporting the engine, it is imperative to install transportation locking devices for crankshaft and engine mounts. Secure the engine against tilting during transportation. The engine must be especially secured against slipping or tilting when going up inclines and ramps.
Setting the Engine down after Transportation Place the engine only on an even, firm surface. Ensure appropriate consistency and load-bearing capacity of the ground or support surface. Never place an engine on the oil pan unless expressly authorised by MTU on a case-by-case basis to do so.
Working with Laser Equipment When working with laser equipment, always wear special laser-protection goggles. Laser equipment can generate extremely intensive, concentrated radiation by the effect of stimulated emission in the range of visible light or in the infrared or ultraviolet spectral range. The photochemical, thermal and optomechanical effects of the laser can cause damage. The main danger is irreparable damage to the eyes. Laser equipment must be fitted with the protective devices necessary for safe operation according to type and application. For conducting light-beam procedures and measurement work, only the following laser devices must be used: •
Laser devices of classes 1, 2 or 3A,
•
Laser devices of class 3B, which have maximum output only in the visible wavelength range (400 to 700 Nm), a maximum output of 5 mW, and in which the beam axis and surface are designed to prevent any risk to the eyes.
Engine Operation When the engine is running, always wear ear protectors. Ensure that the engine room is well ventilated. Mop up any leaked or spilt fluids and lubricants immediately or soak up with a suitable bonding agent. Exhaust gases from combustion engines are poisonous. Inhalation of poisonous exhaust gases is a health hazard. The exhaust pipework must be leak-free and must discharge the gases to atmosphere. During engine operation, do not touch battery terminals, generator terminals or cables. Inadequate protection of electrical components can lead to electric shocks and serious injuries. When the engine is running, never release coolant, oil, fuel, compressed air or hydraulic lines.
15345/20 E 00–05
Section Page
Safety Instructions
! 3
Maintenance and Repair Compliance with maintenance and repair specifications is an important safety factor. Unless expressly permitted, no maintenance or repair work must be carried out with the engine running. The engine must be secured against inadvertent starting and the battery disconnected. Attach sign “Do not operate” in operating area or to control equipment. Persons not involved must keep clear. Never attempt to rectify faults or carry out repairs if you do not have the necessary experience or special tools required. Maintenance and repair work must only be carried out by authorised, qualified personnel. Use only the proper, calibrated tools. Do not work on engines or components which are only held by lifting equipment or crane. Always support these components in accordance with regulations on suitable frames or stands before beginning any maintenance or repair work. Before barring the engine, make sure that nobody is standing in the danger zone. After working on the engine, check that all guards have been reinstalled and that all tools and loose components have been removed from the engine. Fluids emerging under high pressure can penetrate clothing and skin and may cause serious injury. Before starting work, relieve pressure in systems and H.P. lines which are to be opened. Never bend a fuel line and do not install bent lines. Keep fuel injection lines and connections clean. Always seal connections with caps or covers if a line is removed or opened. During maintenance and repair work, take care not to damage the fuel lines. To tighten connections when installing lines, use the correct tightening torque and ensure that all retainers and dampers are installed correctly. Ensure that all fuel injection lines and compressed oil lines have sufficient play to avoid contact with other components. Do not place fuel or oil lines near hot components, except when necessary for design reasons during installation. Take care with hot fluids in lines, pipes and chambers. ⇒ Risk of injury! Note cooling period for components which are heated for installation or removal.
⇒
Risk of injury!
Take special care when removing ventilation or plugs from engine. In order to avoid the discharge of highly pressurised liquids, hold a cloth over the screw or plug. It is even more dangerous if the engine has recently been shut down, as the liquids can still be hot. Take special care when draining hot fluids ⇒ Risk of injury! When draining, collect fluids in a suitable container, mop up any spilt fluids or wipe or soak them up with a suitable bonding agent. When changing engine oil or working on the fuel system, ensure that the engine room is adequately ventilated. When working high on the engine, always use suitable ladders and work platforms. Make sure components are placed on stable surfaces. In order to prevent back injuries when lifting heavy components, adults should only lift weights between max. 10 kg and 30 kg, depending on age and sex. •
Use lifting gear or seek assistance.
•
Ensure that all chains, hooks, slings, etc. are tested and authorised, are sufficiently strong and that hooks are correctly positioned. Lifting eyes must not be unevenly loaded.
Welding Operations Never carry out welding work on the engine or engine-mounted units. Never use the engine as an earth connection. – (This prevents the welding current passing through the engine and causing scorching or burning at bearings, sliding surfaces and tooth flanks, which can lead to pitting or other material damage). Never position the welding power supply cable adjacent to, or crossing MTU plant wiring harnesses. (The welding current can be induced in the wiring harnesses, which could damage the electrical unit.)
15345/20 E 00–05
Section Page
! 4
Safety Instructions
The welding unit earth connection must not be more than 60 cm from the weld point. If components (e.g. exhaust manifold) are to be welded, they must first be removed from the engine. When carrying out work on MTU electronics components, it is not necessary to remove connectors provided that the master switch for power supply has been moved from “ON” to “OFF” and the cable is disconnected from the battery negative and positive terminals.
Hydraulic Installation and Removal Only the hydraulic installation and removal equipment specified in the work schedule and in the assembly instructions must be used. The max. permissible push-on pressure specified for the equipment must not be exceeded. The H.P. lines for hydraulic installation and removal are tested with 3800 bar. Do not attempt to bend or apply force to lines. Before starting work, pay attention to the following: •
Vent the hydraulic installation / removal tool, the pumps and the lines at the relevant points for the system to be used (e.g. open vent plugs, pump until bubble-free air emerges, close vent plugs).
•
For hydraulic installation, screw on the tool with piston retracted.
•
For hydraulic removal, screw on the tool with piston extended.
For a hydraulic installation / removal tool with central expansion pressure supply, screw spindle into shaft end until correct sealing is achieved. During hydraulic installation and removal, ensure that nobody is standing in the immediate vicinity of the component to be installed / removed. As long as the system is under pressure, there is the risk that the component to be installed / removed may be suddenly released from the pressure connection. Before use, the tools must be checked at regular intervals (crack test).
Working on Electrical Assemblies Switch off all live appliances before carrying out any work on electrical assemblies. Gases released from the battery are explosive. Avoid sparks and naked flames. Do not allow battery acids to come into contact with skin or clothing. Wear protective goggles. Do not place tools on the battery. Before connecting the cable to the battery, check battery polarity. Battery pole reversal may lead to injury through the sudden discharge of acid or bursting of the battery body. Do not damage wiring during removal work and when reinstalling wiring and ensure that during operation it is not damaged by contact with sharp objects, by rubbing against another component or by a hot surface. Do not secure wiring to fluid-carrying lines. On completion of the maintenance and repair work, any cables which have become loose must be correctly connected and secured. Always tighten connectors with connector pliers. If wires are installed beside mechanical components and there is a risk of chafing, use cable clamps to properly support the wires. For this purpose, no cable straps must be used as, during maintenance and / or repair work, the straps can be removed but not installed a second time.
15345/20 E 00–05
Safety Instructions
Section Page
! 5
Operation of Electrical Equipment When operating electrical equipment, certain components of this equipment are live. Noncompliance with the warning instructions given for this equipment may result in serious injury or damage to property.
Fire Prevention Rectify any fuel or oil leaks immediately; even splashes of oil or fuel on hot components can cause fires – therefore always keep the engine in a clean condition. Do not leave cloths soaked with fluids and lubricants lying around on the engine. Do not store combustible fluids near the engine. Do not weld pipes and components carrying oil or fuel. Before welding, clean with a nonflammable fluid. When starting the engine with a foreign power source, connect the ground lead last and remove it first. To avoid sparks in the vicinity of the battery, connect the ground lead from the foreign power source to the ground lead of the engine or to the ground terminal of the starter. Always keep suitable fire-fighting equipment (fire extinguishers) at hand and familiarise yourself with their use.
Noise Noise can lead to an increased risk of accident if acoustic signals, warning shouts or noises indicating danger are drowned. At all workplaces with a sound pressure level over 85 dB(A), always wear ear protectors (protective wadding, plugs or capsules).
Environmental Protection Dispose of used fluids and lubricants and filter in accordance with local regulations. Manipulation of the injection or control system can influence the engine performance and exhaust emissions. As a result, compliance with environmental regulations may no longer be guaranteed. Only fuels of the specified quality required to achieve emission limits must be used. In Germany, the VAwS (= regulations governing the use of materials that may affect water quality) is applicable, which means work must only be carried out by authorised specialist companies. (MTU is such a company.)
Auxiliary Materials Use only fluids and lubricants that have been tested and approved by MTU. Fluids and lubricants must be kept in suitable, properly designated containers. When using fluids, lubricants and other chemical substances, follow the safety instructions applicable to the product. Take care when handling hot, chilled or caustic materials. When using inflammable materials, avoid all sparks and do not smoke. ⇒ Lead
When working with lead or lead-containing pastes, avoid direct contact to the skin and do not inhale lead vapours. Adopt suitable measures to avoid the formation of lead dust! Switch on fume extraction system! After coming into contact with lead or lead-containing materials, wash hands! ⇒ Acids
and Alkaline Solutions
When working with acids and alkalis, wear protective goggles or face mask, gloves and protective clothing. Immediately remove clothing wetted by acids and alkalis! Rinse injuries with plenty of clean water! Rinse eyes immediately with eyedrops or clean tap water!
15345/20 E 00–05
Section Page
! 6
Safety Instructions
⇒ Painting
When painting in other than spray booths equipped with extractors, ensure good ventilation. Make sure that adjacent work areas are not affected. It is absolutely essential to wear masks providing protection against paint and solvent fumes. Observe fire prevention regulations! No smoking! No naked flame! ⇒ Liquid
Oxygen
Liquid oxygen is highly inflammable! Liquid oxygen should only be stored in small quantities and in regulation containers (without fixed seals)! Do not bring liquid oxygen into contact with the body (hands) as this causes frostbite and possibly the loss of tissue. No smoking, no naked flame (risk of explosion)! Excessive oxygen in the air leads to explosive combustion. Do not store combustible substances (e.g. oils and greases) within 5 m of the working area! Under no circumstances should clothing be oily or greasy! Do not allow vapours to penetrate clothing! Oxygen enrichment in fabric can cause working clothes to ignite suddenly! After working with liquid oxygen, do not smoke until clothing is free of vapours! Take great care to avoid impact and shock when working with liquid oxygen! ⇒ Liquid
Nitrogen
Store liquid nitrogen only in small quantities and always in regulation containers without fixed covers. Do not bring liquid nitrogen into contact with the body (eyes, hands), as this causes frostbite and numbing. Wear protective clothing (including gloves and closed shoes) and protective goggles! Ensure the room is well ventilated (88% contamination of breathing air with nitrogen will result in suffocation). Avoid all knocks and jars to the containers, fixtures or workpieces! ⇒ Compressed
Air
Compressed air is air which has been compressed at excess pressure and is stored in tanks from which it can then be extracted. The pressure at which the air is kept can be read off at pressure gauges which must be connected to the compressed air tanks and the compressed air lines. When working with compressed air, safety precautions must be constantly observed: • Pay special attention to the pressure level in the compressed air network and pressure vessel! • Connecting devices and equipment must either be designed for this pressure or, if the permitted pressure for the connecting elements is lower than the pressure required, a pressure reducing valve and safety valve (set to permitted pressure) must form an intermediate connection. Hose coupling and connections must be securely attached! • Always wear protective goggles when blowing off tools or extracting chips! • The snout of the air nozzle is provided with a protective disc (e.g. rubber disc), which prevents air-borne particles being reflected and thereby prevents injury to eyes. • First shut off compressed air lines before compressed air equipment is disconnected from the supply line or before equipment or tool is to be replaced! • Unauthorised use of compressed air, e.g. forcing flammable liquids (danger class AI, AII and B) out of containers, results in a “Risk of explosion”! • Forcing compressed air into thin-walled containers (e.g. containers made of tin, plastic and glass) for drying purposes or to check for leaks results in a “Risk of explosion”!
15345/20 E 00–05
Section Page
Safety Instructions
•
! 7
Do not blow dirty clothing with compressed air when being worn on the body! Even compressed air at low pressure penetrates clothing and, if the jet is directed at the back, the air can enter the anal cavity and fatally rupture the intestines!
⇒ Used
Oil
Used oil may contain health-threatening combustion residues. Rub barrier cream into hands! Wash hands after contact with used oil!
Warning Signs
Before putting the engine into service and before working on the engine, read and follow all warning signs. Do not paint over warning signs. Replace illegible signs.
Warning Notices Publication contains especially emphasised safety instructions in accordance with the American standard ANSI Z535, which begin with one of the following signal words according to the degree of danger:
DANGER In event of immediate danger. Consequences: Death or serious injury
WARNING In event of dangerous situations. Consequences: Serious injury
CAUTION In event of dangerous situations. Consequences: Slight injury or material damage Take extreme care in these situations! Read and become acquainted with all warning notices and symbols before operating or repairing this product! Pass on all safety instructions to your operating, maintenance, repair and transport personnel!
15345/20 E 00–05
Section Page
! 8
Safety Instructions
15345/20 E 00–05
Section
Product Summary
A
Contents
A000.000.01
Engine layout
A000.000.03
Engine model designation
A000.000.05
Enginesideandcylinderdesignations
A000.000.09
Main engine dimensions
A000.000.13
Engine weight
A000.000.17
Main engine specifications
A000.000.19
Engine power
A000.000.21O
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . . .
perational data
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5. . .
A000.000.25
Engine and exhaust noise
A050.000.01
Timingdata(valveclearanceadjusted)
A055.050.01V A180.000.01 A202.000.01C
alve clearances capacity Oil
...................................................5 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . .
oolant capacity
15345/20 E 00–05
...........................................3 ....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . .
Section
A
Product Summary
15345/20 E 00–05
Product Summary
Section Page
A000.000.01 Engine Layout Illustrations may show additional equipment
1 2 3 4 5 6 7 8 9 10
Coolant system vent connection Engine oil heat exchanger Centrifugal oil filter Exhaust turbocharger Exhaust outlet Air filter Governor / engine control system Charge air line Starter Engine mount
15345/20 E 00–05
11 Engine oil filter (easy-change filter) 12 Fuel duplex filter (easy-change filter) 13 H.P. fuel pump 14 Vibration damper 15 Charge air coolant pump 16 Charge air coolant thermostat 17 Charge air coolant inlet 18 Engine coolant outlet 19 Charge air coolant outlet 20 Crankcase ventilation
A 1
Section
A
Page
2
1 2 3 4 5 6 7 8 9 10
Air filter Crankcase ventilation Charge air line Exhaust turbocharger Charge air coolant outlet Cylinder head cover / cylinder head Engine lifting eyes Engine coolant pump Oil filler neck Oil pan
Product Summary
11 Oil dipstick 12 Oil drain plug 13 Starter 14Flywheel 15 Flywheel housing 16 Charge air line 17 Governor / engine control system 8 1 Intercooler
A000.000.03 Engine Mod el Desi gnation Explanation of engine type designation 16V4000G20, 16V4000G40, 16V4000G60, 16V4000G80 16 V 4000 G 2, 4, 6, 8
= = = = =
number of cylinders Veeconfiguration displacement per cylinder in cm 3 application for stationary power generation external charge air cooling
0
= designindex
15345/20 E 00–05
Product Summary
Section Page
A 3
A000.000.05 Engine Side and Cylinder Designations Engine sides are always designated as viewed from the driving end. The cylinders on the left engine side are designated “A” and those of the right engine side “B” (as per DIN ISO 1204). The cylinders of each bank are numbered consecutively, starting with No. 1 at the driving end. The numbering of other engine components is also from the driving end, starting with No. 1.
Applicable designations and abbreviations Driving end . . . . . . . . . . . . . . . . . . . . . . . . . . . .KS ..... Free end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .KGS ..
A000.000.09 Main Engi ne Dim ensions A B C D
= = = =
Overalllength . . . . . . . . . . . .approx. . 2880mm Overallwidth . . . . . . . . . . . . .approx. . 1665mm Overallheight . . . . . . . . . . . .approx. . 2400mm Engine length to flange surface . . . . . . . . . . . . . . . . . .approx. . 2610mm E = Crankshaft centreline to oil pan . . . . . 635 . mm F = Crankshaft centreline to engine mount 340 mm
A000.000.13 Engine Weight Enginedry weight (with standard accessories withoutcoupling)
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . .approx. . . . . . 6950 kg
Section
A
Page
4
Product Summary
A000.000.17 Main Engine Spe cifications Operatingmethod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .four-stroke . . . . . cycle,single-acting Combustion method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .direct . . injection ..... Injectionmethod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .common . . . . . rail(accumulatorinjection) Mode of supercharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .exhaust . . . . .turbocharging .. Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .liquid-cooling ...... Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 . . °. .Vee ... Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .mm . . . . . . .165 ....... Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm . . . . .190 ....... Displacement, cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.06 . . litres ...... Number cylinders of . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ............... Displacement, total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64.96 . . .litres ..... Compressionratiowith16V4000G20;G60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16.6 . .1:. . . . . . . Compression ratio with 16V4000G40; G80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 1.: . . . . . . . . . Directionofrotation(viewedondrivingend) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c.c.w. . . . .(non-reversible) .. Firingorder . . . . . . . . . . . . . . . . . . .A1 . –A 7 –B 4 – B6 –A 4 –B 8 – A2 – A8 – B3 –B 5 –A 3 –A 5–B 2 –A 6 – B1 – B7 Finalcompressionpressureat120rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 .to .24 .bar .......
A000.000.19 Engine Pow er Continuouspowerwith16V4000G20 Continuouspowerwith16V4000G40 Continuouspowerwith16V4000G60
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1760 . . . .kW . .at.1500rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1990 . . . .kW . .at.1800rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1940 . . . .kW . .at.1500rpm
Continuouspowerwith16V4000G80
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2190 . . . .kW . .at.1800rpm
Reference conditions – Intake air temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 . . .°C ... – Charge air coolant temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 . . °. C. . – Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 . . .m ... – Exhaust backpressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 . . .mbar .. – Intake air pressure loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 . . .mbar ..
15345/20 E 00–05
Product Summary
Section Page
A 5
A000.000.21 Operational Data The Engine Acceptance Test Records operational data are binding. All figures relate to the engine at operating temperature. The engine may be operated at full power up to the specified limit values. The normal values may approach the limit values as a result of different reference conditions or faults when the prescribed service life is reached. If the limit values are exceeded, determine and rectify the cause.
Coolas ny t stem
Unit
Normal
Limit
Coolant temperature at engine outlet
°C
93
Coolant temperature after engine – warning
°C
95
– –
Coolant temperature after engine – shutdown
°C
–
97
Engine coolant preheat temperature, measured after engine
°C
40
–
Engine oil system Engine oil operating temperature before engine
°C
Engine oil operating temperature before engine – warning
°C
Engineoiloperatingpressurebeforeengine Engineoilpressurebeforeengine–warning
bar bar
85 95 – 95
–
5.0–6.0 4.5
–
Fuel system Primingpressurebeforeenginedeliverypump“min”
bar
–
0.0
Primingpressurebeforeenginedeliverypump“max”
bar
–
1.5
Peripheral conditions for max. power Intake depression Exhaust backpressure
mbar mbar
25 30
35 50
A000.000.25 Engine an d Exh aust Nois e Sound power level as per ISO 8528–10 Applicable to engine model 16V4000G20 – Engine surface noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. .. 107 dB (A) – Undamped exhaust noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . .approx. . 116 dB (A) Applicable to engine model 16V4000G40 – Engine surface noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. .. 106 dB (A) – Undamped exhaust noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . .approx. . 115 dB (A) Applicable to engine model 16V4000G60 – Engine surface noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. .. 108 dB (A) – Undamped exhaust noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . .approx. . 118 dB (A) Applicable to engine model 16V4000G80 – Engine surface noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. .. 108 dB (A) – Undamped exhaust noise (free-field level) at distance of 1 m . . . . . . . . . . . . . . . . . . . . . . . . . . .approx. . 118 dB (A)
15345/20 E 00–05
Section
A
Page
6
Product Summary
A050.000.01 Timing Data (Valve Clearance Adjusted) Valve clearance adjusted
°Crank
1Inletvalveopens . . . . . . . . . . . 42.6 ... 2Inletvalvecloses . . . . . . . . . . . .66.6 .. 3Exhaustvalveopens . . . . . . . . 57.6 ..
before TDC ° after BDC ° before BDC
angle
°
4 Exhaust valve closes . . . . . . . . . . . .°
Overlap 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 . . . . . . 6 Start of delivery . . . . . Performance-map controlled I . . . . . . . . . . . . . . . . . . . . . . .Top . dead center (TDC) II . . . . . . . . . . . . . . . . . . . Bottom . dead center (BDC)
A055.050.01 Valve Clearances With engine cold – Inlet valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.20 . . . .mm .. – Exhaust valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.50 . . . .mm ..
A180.000.01 Oil Cap acity
Oil capacity, oil pan – to lower mark on oil dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. . . . . . 190 litres – to upper mark on dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. . . . . . 230 litres Total capacity – for initial filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. . . . . . . 290 litres – for oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. . . . . . . 250 litres
A202.000.01 Coolant Capacity – Engine circuit (without cooler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. . . . . . 175 litres – Charge air circuit (without cooler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .approx. . . . . 40 litres
15345/20 E 00–05
Section
Operating Instructions
C
Contents
C000.000.01
Operating instructions – Preface
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ....
C000.000.03
Preparationsforinitialoperation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. . .
C000.000.05I
nitial operation
C000.000.07
Operationalchecks–MaintenanceEchelonW1–
C000.000.09
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.
C000.000.11
After shutdown
C000.000.13
Out-of-service period
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. .
C000.000.17
Engine transportation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. .
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. . . .
Section
C
Operating Instructions
15345/20 E 00–05
Operating Instructions
Section
C
Page
1
C000.000.01 Operating Instructions – Preface Low operating and maintenance costs as well as operational reliability and availability depend on maintenance and servicing being carried out in compliance with our specifications and instructions. Our Product Support service is available at all times should assistance be needed. Prior to engine start-up it must be determined whether start-up is: – After a short, scheduled operational shutdown, – After an extended out-of-service period, – Initial startup of a new engine. Accordingly the Before-Operation Services are sub-divided into: – B1- Before-Operation Services after a short, scheduled operational shutdown (B1) – B2- Before-Operation Services after an extended operational shutdown (exceeding 1 week) (B2) – B3- Before-Operation Services before initial startup of a new or preserved engine (B3). Correct engine installation and alignment according to our regulations are basic requirements for initial engine startup. In the event of an engine malfunction a decision must be made as to whether – The engine is to be shut down – operation may be continued, for a short period, using emergency measures, until rectification can be effected. Prior to engine shutdown it must be determined whether: – a short, scheduled operational shutdown, or – an extended out-of-service period is involved. NOTE: The code numbers on the following pages refer to the group numbers in Section G. This Maintenance Schedule may include components which are not installed on your engine; these may be disregarded.
15345/20 E 00–05
Section
C
Page
2
Operating Instructions
C000.000.03 Preparations for Initial Operation Code
Task Description
G080.000.03 Fuelsystem G124.051.01 Charge air manifold G180.000.01 Engineoil
Check drain line for water discharge and obstruction Checklevel
G202.000.03 Engine coolant
Check level
G202.400.01 Enginecoolant
Preheat
G203.000.03 Charge air coolant
Check level
G307.001.01 Guards
Check
G364.050.01 Fuel G364.200.03 Fuel supply system
Checksupply Open shut-off valve(s)
G500.000.01 Engine control system
Switch on
G500.000.09 Enginewiring
Check
G000.000.05 Running gear
Bar engine manually
G202.651.01 Engine coolant system
Check vent line for obstructions
G203.551.01 Charge air coolant system
Check vent line for obstructions
K000
Depreservation
Carry out before-operation services
G055.000.03 Valvegear
Lubricate
G120.000.07 Air system
Ensure cover plates are removed
G140.000.03 Exhaust s ystem
Check tightness of securing screws
G140.000.07 Exhaust system
Ensure cover plates are removed
G180.000.03 Engineoil
Fillsystem
G202.000.01 Engine coolant
Fill system
G202.401.01 Preheater G203.000.01 Charge air coolant G309.001.03 Battery G364.200.05 Fuel supply system G500.000.07 Engine control system
B 1 2 3
Fillsystem
Switchon Fill system Fillwith acid / alkaline solution Fill fuel suction line to engine Switch on
T036.051.01
Crankshaft
Ensure transportation locking device is removed
T231.001.01
Engine mounting
Ensure locking device is removed
15345/20 E 00–05
Operating Instructions
C000.000.05 Initial Operation Code
Task Description
G000.000.07 Engine
Turnengineonstarter: – only on initial operation after engine oil change after engine oil filter change after extended out-of-service period (exceeding 1 month) Startengine
Carry out before-operation services
G000.000.09 Engine G000.000.11
Engine operation
G000.000.13 Engine operation G000.000.15 Engine operation
Carry out warm-up procedure Check speed Check pressures (where gauges are installed)
G000.000.17 Engine operation
Check t emperatures (where gauges a re installed)
G000.000.19 Engine operation
Check running noises
G000.000.21 Engine operation
Check engine and external pipework for leaks
For B2 or B3 and after W6, in addition: G055.000.01 Valvegear
Checkoilsupply
G080.000.05 Engine test run
Check fuel delivery pump supply pressure
G120.000.05 Engine test run
Check intake depression
G140.000.09 Engine test run
Check exhaust backpressure
C000.000.07 Operational Checks – Maintenance Echelon W1– Carry out tasks in accordance with Maintenance Schedule Section D.
15345/20 E 00–05
Section
C
Page
3
Section
C
Page
4
Operating Instructions
C000.000.09 Shutdown Code
Task Description
G000.000.23 Engine
Shutdownengine
G000.000.35 Engine
Disengageload
C000.000.11 After Shutdown Code
Task Description
G180.000.01 Engineoil
Checklevel
C000.000.13 Out-of-Service Perio d If the engine is to remain out of service for more than 1 week, seal the engine air and exhaust sides. If the engine is to remain out of service for more than 1 month, carry out preservation in accordance with Section K. Code
Task Description
G202.000.07 Enginecoolant
Drain (1)
G202.401.05 Engine coolant G203.000.05 Charge air coolant
Switch off preheating unit Drain (1)
G500.000.03 Engine control system
Switch off
(1) only
– – – –
when freezing temperatures are expected and the engine is to remain out of service for an extended period and
the engine coolant has no antifreeze additive the engine room cannot be heated the coolant cannot be maintained at a suitable temperature the antifreeze concentration is insufficient for the engine room temperature
– or with an antifreeze concentration of 50% and at an engine room temperature below –40 °C, if the antifreeze additive conforms to the current MTU/DDC Fluid and Lubricants Specification.
C000.000.17 Engine Tra nsportation Before transporting the engine, the transportation locking devices for the crankshaft (Section T) must be installed. The engine must only be lifted using the lifting eyes provided.
15345/20 E 00–05
Maintenance Schedule
Section
D
Contents
D000.000.01
Maintenance schedule – Preface
D000.000.03
Maintenance system
D000.000.05
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
D000.000.07
Maintenance frequency chart
D000.000.11
Maintenance schedule
D000.000.15
Maintenance echelon W6
D000.000.17
Out-of-service periods
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. .
Section
D
Maintenance Schedule
15345/20 E 00–05
Maintenance Schedule
Section Page
D 1
D000.000.01 Maintenance Schedule – Preface Low operating and maintenance costs as well as operational reliability and availability depend on maintenance and servicing being carried out in compliance with our specifications and instructions. The overall system, of which the engine is an integral part, must be maintained in such a way as to ensure troublefree engine operation at all times. For this purpose, always: – Ensure that sufficient fuel is available – Ensure that the combustion air is dry and clean – Use only clean, filtered raw water Preventive maintenance instructions – Special care should be taken to keep the machinery plant in a clean and serviceable condition at all times to facilitate detection of possible leaks and prevent subsequent damage. – Protect rubber and synthetic parts from oil and fuel, never treat with organic detergents. Wipe with a dry cloth only. – Always replace all seals and gaskets.
D000.000.03 Maintenance System The MTU maintenance concept is a preventive maintenance concept and features the W1 to W6 Maintenance Echelons as outlined below. Preventive maintenance permits advance operational planning and increases availability. Main features of maintenance echelon W1:
Operationalchecks.
W2, W3 and W4:
Periodic maintenance services to be carried out during out-of-service periods without the need for engine disassembly.
W5
–
W6:
Major overhaul. This echelon requires complete engine disassembly.
The time intervals according to which W2 to W6 maintenance operations are to be performed and the relevant inspection and maintenance tasks are based on operational experience. They have been determined so as to ensure correct engine operation until the next scheduled maintenance echelon. Particular operating conditions may require the Maintenance Schedule to be altered to compensate. NOTE: The code numbers on the following pages refer to the group numbers in Section G. This Maintenance Schedule may include components which are not installed on your engine; these may be disregarded.
D000.000.05 Application 3D:
Emergency power operation
4C: 4C:
Short-term operation: Drive for industrial machinery (e.g. fire-fighting pumps, emergency water supply) Continuous operation, restricted (emergency power operation) Continuous operation, restricted (peak-load operation) – see maintenance schedule MO 50 479
15345/20 E 00–05
Section Page
D 2
Maintenance Schedule
D000.000.07 Maintenance Frequency Chart Maintenanceechelon
W1:
every month in extended operation daily
1
W2:
every months operating hours limit
6 250
W3:
every year operating hours limit
1 500
W4:
every year operating hours limit
4 1 500
W5:
every year operating hours limit
8 3 000
W6:
every year operating hours limit
16 6 000
D000.000.11 Maintenance Sch edule Code
One-time services after the first 50 operating hours on a new engine, or after W5 or W6 maintenance
G055.050.01 Valvegear
Check valve clearances
G073.051.07 H.P. fuel pump
Check relief bore for obstructions
G083.051.03 Fuel duplex filter
Replace filter element
G083.101.03 Fuel prefilter
Drain water and contaminants
G083.101.09 Fuel prefilter
Replace filter element
G083.101.15 Fuelprefilter
Clean
G140.000.03 Exhaust s ystem
Check tightness of securing screws
G180.000.04 Engine oil G202.051.01 Engine coolant pump
Used oil – take sample and analyse Check relief bore for obstructions
G203.051.01 Charge air coolant pump
Check relief bore for obstructions
Code
Maintenance echelon W1 – Monthly test run / operational checks
G000.000.13 Engine operation
Check speed
G000.000.15 Engine operation
Check pressures (where gauges are installed)
G000.000.17 Engine operation
Check t emperatures (where gauges a re installed)
G000.000.19 Engine operation
Check running noises
G000.000.21 Engine operation
Check engine and external pipework for leaks
G083.101.03 Fuel prefilter
Drain water and contaminants
G121.052.01 Air filter
Check contamination indicator
G124.051.01 Air supply pipework
Check drain bore for water discharge and obstruction
G140.000.05 Exhaust s ystem
Check exhaust gas colour
G140.000.11
Exhaust system
G180.000.01 Engineoil
Drain (if drain provided) Checklevel
G202.000.03 Engine coolant
Check level
G203.000.03 Charge air coolant
Check level
G303.000.03 Compressed air system
Drain condensate
G303.000.03 Compressed air system
Check operating pressure
G510.070.01 Monitoring s ystem
Carry out lamp test
15345/20 E 00–05
Maintenance Schedule
Code
Section Page
Task Description
W 2 3 4 5
G120.000.03
Air supply pipework
Check intake side for leaks or damage
G180.000.04
Engine oil
Used oil – take sample and analyse
G180.000.05
Engineoil
Change – after every 2 years – at the latest with oil category 1 after every 250 operating hours oil category 2 after every 500 operating hours
G183.052.03
Engineoilfilter
Replace – when changing oil
G055.050.01 G083.051.03
Valve gear Fuel duplex filter
G083.101.09
Fuel prefilter
Replace filter element
G083.101.15
Fuelprefilter
Clean
G140.000.11
Exhaust s ystem
Check, check drain bore for obstruction
G202.000.05
Engine coolant
Take sample and analyse (engine coolant change – see MTU Fluids and Lubricants Specification)
G202.051.01
Engine coolant pump
Check relief bore for obstructions
G203.000.07
Charge air coolant
Take sample and analyse, change if necessary (see MTU Fluids and Lubricants Specification)
G203.051.01
Charge air coolant pump
Check relief bore for obstructions
G205.051.01
Engine coolant cooler
Check cooler elements for external contamination
G205.051.03
Charge air coolant cooler
Check cooler elements for external contamination
G073.051.07
H.P. fuel pump
Check relief bore for obstructions
G121.051.01
Airfilter
Replacefilterelements
G172.051.09
Starter
Check condition (visual inspection)
G213.051.01
Generator drive
Check drive belt condition and tension
G213.051.08 G231.051.01
Generator Engine mounting
Check condition (visual inspection) Check tightness of securing screws
G231.051.03
Engine mounting
Check condition of resilient mounts
G231.051.11
Enginemounting
Check bufferc learance
G252.051.01
Coupling ( flywheel e nd)
Check c ondition ( visual i nspection)
G500.000.09
Enginewiring
Check
G510.000.01
Monitoring s ystem
Check valve clearances Replace filter element
Check function of monitoring units
At < 2000 operating hours, the * tasks may be omitted: Before starting W5 maintenance services, drain coolant and flush coolant systems. * Valve gear
Remove and check rocker arms and valve bridges Check rocker arms, rollers, pushrod seats and rocker arm bearings for wear
* Cylinder heads
Remove, check valve guides, recondition valves and valve seats Replace O-rings on protective sleeves Replace gaskets
* Fuelinjectors
Replace
* Crankcase
Check wear pattern of cylinder liners
* Vibration damper
Examine, repair if necessary
Exhaust turbocharger
Visual inspection, check bearing clearance, replace if necessary
Air supply pipework
Remove, clean, and replace gaskets
Intercooler
Remove, clean, check for leaks, replace gaskets
Generator H.P.fuelsensor Engine coolant pump
Checkcarbonbrushes Replace Check for leaks, disassemble if necessary, replace gaskets
Charge air coolant pump
Check for leaks, disassemble if necessary, replace gaskets
Engine coolant cooler
Clean, check for leaks
Charge air coolant cooler
Clean, check for leaks
Engine coolant thermostat
Check, replace thermal element
Charge air coolant thermostat
Check, replace thermal element
15345/20 E 00–05
D 3
Section Page
D 4
Maintenance Schedule
Engine coolant preheating
Overhaul
Engine oil heat exchanger
Remove, clean and check for leaks, replace sealing rings
Crankcase breather
Check oil separator, replace if necessary
D000.000.15 Maintenance Ech elon W6 The W6 echelon requires complete disassembly of the engine. Repair / overhaul of the relevant components is determined by the actual condition of the components and their dimensions, which are referenced to the Tolerances and Wear Limits List.
D000.000.17 Out-of-Service Perio ds If the engine is to remain out of service for several weeks, spray engine oil into the engine air intake. Operate the engine shutdown device and use the starting equipment to turn the engine over while performing this procedure. The maintenance schedule will then be governed by the time limits specified. In addition, the engine must be turned over by hand once a month. If the engine is to remain out of service for more than 1 month, carry out engine preservation in accordance with Section K.
15345/20 E 00–05
Section
Troubleshooting
E
Contents
E000.000.01
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
E000.000.02
Enginedoesnotturnwhenstarterisactuated
E000.000.03
Engine turns but does not fire
E000.000.05
Engine fires unevenly
E000.000.07
Enginedoesnotreachfull-loadspeed
E000.000.09
Engine speed not steady
E000.000.11
Compression pressure too low
E070.000.01
Fuel pressure too low
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. . . . . . .
E070.000.03
Fuel pressure too high
.....................................................4 .......
E073.051.01
H.P. pump leaking at relief bore
E080.000.01
Fuel pressure too low
E101.011.01
Abnormalturbochargerrunningnoises
E110.000.01
Charge air temperature too high
E110.000.03
Charge air pressure too low
E114.051.01
Coolantdischargeatintercoolerreliefbore
E140.000.01
Exhaust gases black
E140.000.02
Exhaust gases blue
E140.000.03
Exhaust gases white
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . .
E172.000.01
Power supply faulty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . .
E180.000.01
Engineoilconsumptionabnormallyhigh
E180.000.03
Engine oil level abnormally high
E180.000.05
Engine oil temperature too high
E180.000.07
Engine oil pressure too high
.................................................8 .......
E180.000.09
Engine oil pressure too low
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. . . . . . .
E202.000.01
Enginecoolanttemperaturetoohigh
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . . .
E202.000.02
Enginecoolanttemperaturetoolow
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . . .
E202.000.05
Engine coolant pressure too low
E202.000.07
Coolant loss
E202.000.09
Engine coolant level rising
E202.051.01
Enginecoolantpumpleakingatreliefbore
E202.400.01
Preheat temperature too low
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. . . . . . . . ........................................................2 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7. . . . . ...............................................7 ......
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ......
Section
E
Troubleshooting
15345/20 E 00–05
Troubleshooting
Section Page
E 1
E000.000.01 General In Event of Internal Coolant Leakage Subsequent damage caused by corrosion must be avoided. If the engine cannot be repaired immediately, carry out the following operations: – Drain coolant and engine oil – Introduce corrosion-inhibitor oil, kerosene or diesel fuel into the crankcase via the oil filler neck until the max. level is reached – Remove the charge air/coolant manifolds – Remove the fuel injectors – Bar the engine manually and spray corrosion-inhibitor oil, kerosene or diesel fuel into the combustion chambers via the opening inlet valves It is essential to change the engine oil after 50 operating hours as the new oil may be contaminated by coolant residues left in the crankcase. NOTE: The anti-corrosive protection is restricted to a few days. Repair the engine as soon as possible and thoroughly clean the components.
Before restarting the repaired engine, fill with new oil and coolant in compliance with the MTU Fluids and Lubricants Specification.
Engine Oil Diluted by Fuel It is essential to change the engine oil before restarting the engine after rectifying the fault. Remove the old oil from the crankcase with particular care. Replace the engine oil filter.
After Work on Engine If running gear components, e.g. pistons, piston rings, cylinder liners, etc. have been replaced, carry out the engine running-in procedure.
E000.000.02 Engine does not turn when starter is actuated Probable Causes
Check
Remedial Action
Battery
Battery charge state Cable connections
Charge battery, replace if necessary Connect, replace if necessary
Starter
Starter/engine wiring Start repeat relay Starter Ring gear
Connect, replace if necessary Replace Replace Replace
Running gear blocked
Whether engine can be turned by hand
Repair running gear
Engine wiring
Engine wiring
Check – see G500.000.09
ECU
Check security of connectors and cables
Check – see G508.000.01
E000.000.03 Engine turns but d oes not fir e Probable Causes
Check
Remedial Action
Engine coolant preheat temperature too low
See E202.400.01
–
Fuel pressure too low, no start release
See E070.000.01
–
15345/20 E 00–05
SectionE Page 2
Troubleshooting
Probable Causes
Check
Remedial Action
Engine receiving insufficient combustion air
Air filter contamination indicator (G121.051.01) Air filter Intercooler
– – Replace (G121.051.01) Clean, replace if necessary
Engine does not reach firing speed
Battery Starter
Charge, replace if necessary Replace
Engine wiring
Engine wiring
Check – see G500.000.09
E000.000.05 Engine fires unevenly Probable Causes
Check
Remedial Action
Engine coolant preheat temperature too low
See E202.400.01
–
Fuel system is not yet vented
Whether engine fires steadily after short period
–
Fuel injection equipment faulty
Injectors Pressure maintaining valves Injection pump solenoid valve
Replace (G075.051.05) Replace
Engine wiring
Engine wiring
Check – see G500.000.09
E000.000.07 Engine does not reach full-load speed Probable Causes
Check
Remedial Action
Engine receiving insufficient combustion air
See E110.000.03
–
Engine receiving insufficient fuel
See E080.000.01
–
Fuel injection equipment faulty
Injectors Pressure maintaining valves
Replace (G075.051.05) Replace
H.P. pump generating insufficient pressure
See E070.000.01
–
Charge air temperature too high
See E110.000.01
–
Power take-off too high
Auxiliary PTO (power consumption too high) Dialogue unit/data recorder (speedsensitive fuel limiter actual/specified injection)
Contact MTU Service
15345/20 E 00–05
Troubleshooting
Section Page
E000.000.09 Engine speed not steady Probable Causes
Check
Remedial Action
Fuel injection equipment faulty
Injectors Pressure maintaining valves
Replace (G075.051.05) Replace
H.P. pump
Fuel pressure with dialogue unit/ data recorder
Contact MTU Service
Suction valve sluggish
Check suction valve for ease of movement
Repair, replace if necessary
Speed sensor faulty
Crankshaft speed sensor (G510.000.01) Camshaft speed sensor – see Repair Manual
– –
E000.000.11 Compression pre ssure too low Probable Causes
Check
Remedial Action
Cylinder head gasket leaking
Cylinder head gasket
Replace
Valve seats in cylinder head worn
Cylinder head (G000.000.33)
Repair if necessary
Valves do not close
Valve clearances (G055.050.01) Valves
Adjust (G055.050.03) Recondition, replace if necessary
Piston rings worn
Piston rings
Replace
Combustion chamber
Cylinder liner (G000.000.33) Piston (G000.000.33)
Replace if necessary Replace if necessary
E070.000.01 Fuel pressure too low Probable Causes
Check
Remedial Action
Pressure sensor faulty
Pressure sensor (G510.000.01)
–
H.P. pump of fuel quantity regula- Suction valve tor / pressure regulator (actuating solenoid)
Repair, replace if necessary
Pressure relief valve leaking
Fuel return from pressure relief valve
Replace pressure relief valve
Fuel pressure less than 4 bar
See E080.000.01
–
H.P. pump generating insufficient pressure
Fuel pressure with dialogue unit/ data recorder
Replace H. P. fuel pump
Fuel injector faulty
Fuel pressure with dialogue unit/ data recorder
Replace injector (G075.051.05)
15345/20 E 00–05
E 3
SectionE Page 4
Troubleshooting
E070.000.03 Fuel pressure too high Probable Causes
Check
Remedial Action
H.P. pump of fuel quantity regula- Harsh engine running noise at idling, Repair, replace if necessary tor / pressure regulator (actuating connector and wiring solenoid) Suction valve Pressure sensor faulty
Pressure sensor (G510.000.01)
–
E073.051.01 H.P. pump leaking at relief bore Probable Causes
Check
Remedial Action
H.P. pump seals leaking
For engine oil or fuel discharge
Replace H. P. fuel pump
E080.000.01 Fuel pressure too low Probable Causes
Check
Remedial Action
Fuel supply blocked
Shut-off valve in fuel system
Open (G364.000.03)
Fuel level too low
Fuel supply
Top up fuel
Fuel line
Seals
Renew seals, replace if necessary
Fuel filter contaminated
Fuel prefilter
Clean filter (G083.101.15), replace if necessary (G083.101.09) Replace filter (G083.051.03)
Fuel duplex filter Fuel delivery pump faulty
Fuel delivery pump, fuel delivery pump drive
Repair, replace if necessary
E101.011.01 Abnormal turbocharger running noises Probable Causes
Check
Remedial Action
Exhaust turbocharger dirty
Exhaust turbocharger
Clean
Exhaust turbocharger faulty
Turbocharger bearing Rotor assembly
Replace Replace
E110.000.01 Charge ai r temp erature too hig h Probable Causes
Check
Remedial Action
Intercooler dirty
Intercooler
Clean
Charge air coolant temperature too high
See E203.000.01
–
Antifreeze concentration too high
Charge air coolant
Rectify concentration as per specifications
Incorrect corrosion inhibitor (deposits in intercooler)
Charge air coolant Corrosion inhibitor
Clean coolant system. Treat engine coolant in accordance with the current MTU Fluids and Lubricants Specification, replace intercooler if necessary
15345/20 E 00–05
Troubleshooting
Section Page
E110.000.03 Charge air pr essure too low Probable Causes
Check
Remedial Action
Engine receiving insufficient combustion air
Air filter-contamination indicator (G121.052.01) Charge air pressure (A000.000.21) Air filter Intercooler Air supply pipework
–
Pressure sensor faulty
Pressure sensor (G510.000.01)
–
Exhaust turbocharger faulty
Exhaust turbocharger
Repair
– Replace (G121.051.01) Clean, replace if necessary Seal pipework
E114.051.01 Coolant discharge at intercooler relief bore Probable Causes
Check
Remedial Action
Intercooler leaking
Whether coolant discharges from condensate drain line (not condensate)
Replace intercooler
E140.000.01 Exhaust gases black Probable Causes
Check
Remedial Action
Engine receiving insufficient combustion air
See E110.000.03
–
Fuel injection equipment faulty
See E000.000.07
Resistance in exhaust system
Exhaust backpressure
Clean exhaust silencer
Power take-off too high, engine overload
Auxiliary PTO (power consumption too high) Dialogue unit/data recorder (speedsensitive fuel limiter actual/specified injection)
Contact MTU Service
E140.000.02 Exhaust gases blue Probable Causes
Check
Remedial Action
Too much oil in combustion chambers
Engine oil level (G180.000.01) Exhaust turbocharger Crankcase breather Valve stem seals
Correct oil level (G180.000.01) Repair Replace (G018.101.03) Replace
Piston rings Valve guides Cylinder liners
Replace Replace Replace
15345/20 E 00–05
E 5
SectionE Page 6
Troubleshooting
E140.000.03 Exhaust gases white Probable Causes
Check
Remedial Action
Engine coolant preheat temperature too low
See E202.400.01
–
Engine cold
Engine coolant temperature
See E202.000.02
Coolant in combustion chambers
Exhaust turbocharger Intercooler
Repair Replace
Cylinder head gaskets Cylinder heads (G000.000.33) Cylinder liners (G000.000.33)
Replace Replace if necessary Replace if necessary
E172.000.01 Power supply faulty Probable Causes
Check
Remedial Action
Battery not or insufficiently charged
Generator drive belt Generator Battery
Adjust tension (G213.051.01), replace drive belt if necessary (G213.051.05) Repair Replace
Charge indicator lamp does not light up when engine is inoperative and propulsion control lever is switched on
Connection cable Charge indicator lamp Battery Generator voltage regulator Generator
Secure Replace Replace Replace Repair
With engine inoperative, charge indicator lamp burns brightly but becomes dark when engine running
Connection Generator cable
Secure Repair
Charge indicator lamp still lights up brightly at higher speed
Connection cable from generator to starter/battery Generator drive Generator
Secure
Charge indicator lamp flickers
Generator Generator drive belt
Tighten cable fixtures Adjust tension (G213.051.01) Replace drive belt if necessary (G213.051.05)
Wiring faulty
Wiring
Check G500.000.09
Replace Repair
15345/20 E 00–05
Troubleshooting
Section Page
E 7
E180.000.01 Engine oil consumption abnormally high Probable Causes
Check
Remedial Action
Crankcase ventilation faulty
Crankcase breather
Replace
Engine oil system leaking externally
External subassemblies External pipework Engine oil drains Shaft seals Oil pan Crankcase
Seal pipework Check connections, tighten if necessary Seal (G180.000.05) Replace Seal pipework Repair
Intake air depression too high
Air filter contamination indicator (G121.052.01)
Replace air filter (G121.051.01)
Oil pipes to engine oil heat exchanger leaking
Oil in coolant system
Replace sealing rings
Exhaust turbocharger leaking
Exhaust turbocharger
Replace bearings
Engine wear
Valve stem seal Piston rings Valve guides Cylinder liners
Replace Replace Replace Replace
Combustion chamber
Combustion chamber (G000.000.33) –
E180.000.03 Engine oil le vel ab normally high Probable Causes
Check
Remedial Action
Fuel or engine coolant in engine oil
Engine oil quality
see
Fuel in engine oil
Injectors H.P. pump Relief bore
Replace seal to cylinder head In event of fluid discharge, replace H.P. pump
Engine coolant in engine oil
Cylinder heads Cylinder liner seals Cylinder liners Crankcase Coolant distribution housing
Replace if necessary Replace Replace Repair Replace
– “Fuel in engine oil” – “Coolant in engine oil”
E180.000.05 Engine oi l temp erature too hig h Probable Causes
Check
Remedial Action
Engine oil heat exchanger dirty
Engine oil heat exchanger
Clean, replace if necessary
Engine coolant temperature too high
See E202.000.01
See E202.000.01
Temperature sensor faulty
Temperature sensor (G510.000.01)
–
Combustion chamber
Combustion chamber (G000.000.33) –
15345/20 E 00–05
SectionE Page 8
Troubleshooting
E180.000.07 Engine o il pre ssure too h igh Probable Causes
Check
Remedial Action
Oil viscosity too high
Engine oil viscosity
Change engine oil
Engine oil system
Engine oil pressure relief valve
Replace
Engine coolant in engine oil
Engine oil quality
See E180.000.03
Pressure sensor faulty
Pressure sensor (G510.000.01)
–
E180.000.09 Engine oil pr essure too low Probable Causes
Check
Remedial Action
After oil filter change, the pure oil Drain plugs on equipment carrier or contaminated oil drain plugs on equipment carrier are still open
Close drain plugs
Oil level too low
Engine oil level
Top up engine oil
Engine oil system leaking externally
See E180.000.01
See E180.000.01
Fuel in engine oil
Engine oil quality
See E180.000.03
Engine oil filter dirty
–
Replace filter (G183.052.03)
Engine oil pressure relief valve
Opening pressure
Adjust or replace
Engine oil pump
Engine oil pump
Repair, replace if necessary
Pressure loss in running gear
Running gear lubrication points
Replace bearings
Pressure sensor faulty
Pressure sensor (G510.000.01)
–
E202.000.01 Engine coolant temperature too high Probable Causes
Check
Remedial Action
Engine coolant level too low
Engine coolant level
Top up engine coolant
Engine coolant system contaminated
Engine coolant system Vent lines Engine coolant heat exchanger
Clean Clean Clean, replace if necessary
Engine coolant pressure too low
See E202.000.05
See E202.000.05
Engine coolant thermostat
Engine coolant thermostat
Replace
Temperature sensor faulty
Temperature sensor (G510.000.01)
–
E202.000.02 Engine coolant temperature too low Probable Causes
Check
Remedial Action
Engine coolant thermostat
Engine coolant thermostat
Replace
Temperature sensor faulty
Temperature sensor (G510.000.01).
–
15345/20 E 00–05
Troubleshooting
Section Page
E 9
E202.000.05 Engine co olant pre ssure too low Probable Causes
Check
Remedial Action
Coolant system not sealed
Cover closed Breather valve
Close cover Replace cover
Engine coolant system leaking externally
External pipework External subassemblies Coolant drain points Engine coolant heat exchanger Crankcase
Check connections, tighten if necessary Check connections, tighten if necessary Seal Repair Check for leaks, replace if necessary
Engine coolant level too low
Engine coolant level
Top up engine coolant
Engine coolant pump faulty
Engine coolant pump
Replace
Engine coolant system leaking internally
Engine oil quality Cylinder heads Injector protective sleeve gasket Cylinder liner gaskets
Change engine oil (G180.000.05) Replace Replace Replace
Pressure sensor faulty
Pressure sensor (G510.000.01)
–
Check
Remedial Action
E202.000.07 Coolant lo ss Probable Causes
Engine coolant system leaking ex- See E202.000.05 ternally
–
Engine coolant system leaking internally
See E202.000.05
–
Engine coolant pump leaking
Engine coolant pump
Repair
Level monitor display error
Level monitor, wiring
Repair, replace if necessary
E202.000.09 Engine c oolant le vel ri sing Probable Causes
Check
Remedial Action
Engine oil in engine coolant
Engine coolant quality Engine oil heat exchanger
(G202.000.05) Repair, replace if necessary
Air in engine coolant
Vent lines
Clean
E202.051.01 Engine coolant pump leaking at relief bore Probable Causes
Check
Remedial Action
Engine coolant pump leaking
For oil discharge
Replace sealing ring Replace engine coolant pump if necessary Replace rotary seal Replace engine coolant pump if necessary
For water discharge
15345/20 E 00–05
SectionE Page 10
Troubleshooting
E202.400.01 Preheat temp erature too lo w Probable Causes
Check
Remedial Action
Power supply for preheater
Power supply available
Provide power supply
Preheater not working
Preheater switched on
See Operating Instructions of Manufacturer
15345/20 E 00–05
Section
Task Description
G
Contents
G000.000.01 G000.000.03E
Engine start disabling
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . .
ngine start release
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. . . . .
G000.000.05
Barring engine manually
G000.000.07
Barringenginewithstartingsystem
G000.000.09
Engine starting
G000.000.11
Engine warm-up procedure
G000.000.13E
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 ....
ngine speed check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . .
G000.000.15
Engine pressure checks
G000.000.17
Engine temperature checks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . .
G000.000.19
Engine running noise check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . .
G000.000.21
Engineandexternallinesleakcheck
G000.000.23
Engine shutdown
G000.000.25E
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . .
mergency shutdown
..........................................................4 ...
G000.000.27
Attachments security check
G000.000.29
Attachments,hosesandhoseconnectionscheck
G000.000.33
Cylinderchamberendoscopicexamination
G000.000.39
Cleaning engine externally
G018.101.03
Crankcaseventilation,oilseparatorcheck
G030.001.01
Engine barringtool installation
G030.001.03
Engine barring tool removal
G055.000.01
Valve gear oil supply check
G055.000.03
Valve gear lubrication
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 .....
G055.050.01
Valve clearance check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 .....
G055.050.03
Valve clearance adjustment (Valve bridge with adjusting screw M16 (Locknut 24 AF))
......
15
G055.050.03
Valve clearance adjustment (Valve bridge with adjusting screw M12 (Locknut 19 AF))
......
20
G055.101.01
Cylinder head cover removal
G055.101.03
Cylinderheadcoverinstallation
G073.051.07
High-pressurepump,reliefboreobstructioncheck
G075.051.01I
njector removal
G075.051.05
Injector replacement
G075.051.09
Injector installation
G080.000.03F
uel system filling
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7. . . ........................................8 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 .......
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 ......
G080.000.05 G083.051.03
Fuelsystem,fueldeliverypumpsupplycheck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 ..... Fuel duplex filter replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 .....
G083.101.01
Fuel prefilter priming
G083.101.03
Fuelprefilter,waterandcontaminantsdraining
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ...
G083.101.09
Fuelprefilter,elementandgasketreplacement
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ...
G083.101.15
Fuel prefilter cleaning
G101.011.01
Exhaust turbocharger, engine operation in event of turbocharger failure
G101.011.05
Exhaustturbochargerconnectionscheck
G120.000.03
Intakeairsystem,intakesideleakanddamagecheck
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ..... . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ....
Section
G
Task Description
G120.000.05
Intakeairsystem,intakedepressioncheck
G120.000.07
Intake air system check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ....
G121.051.01
Air filter replacement
G121.052.01
Airfilter,contaminationindicatorpositioncheck
G124.051.01
Charge air manifold, drain water discharge and obstruction check
G124.051.03
Chargeairmanifolddraincleaning
G140.000.01
Exhaust system check
G140.000.03
Exhaust system security check
G140.000.05
Exhaustsystem,exhaustgascolourcheck
G140.000.07
Exhaust system check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 ....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 .....
G140.000.09
Exhaustsystem,exhaustbackpressurecheck
G140.000.11
Exhaustsystemdrainobstructioncheck
G146.000.01
Exhaust system, security and exhaust manifold insulation checks
G172.051.09
Starter condition check
G180.000.01
Engine oil level check
G180.000.03
Engine oil system filling
G180.000.04
Engineoilsampleextractionandanalysis
G180.000.05E
. . . . . . . . . . . . . . . . . . . . . .42 .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 .... . . . . . . . . . . . . . . . . . . . . . . 44 .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 ....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 ....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 .....
ngine change oil
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 ......
G180.000.07
Engine oil draining
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 ......
G180.000.09
Corrosion inhibitor oil Filling
G180.000.11
Corrosion inhibitor oildraining
G183.052.03
Engine oil filter replacement
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 .....
G183.101.01
Centrifugal oil filter cleaning
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 .....
G202.000.01
Engine coolant system filling
G202.000.03
Engine coolant level check
G202.000.05
Enginecoolantsampleextractionandanalysis
G202.000.07
Drain engine coolant
G202.000.09
Engine coolant change
G202.051.01
Enginecoolantpumpreliefborecheck
G202.400.01
Engine coolant preheating
G202.401.01
Enginecoolantpreheatingunitinitialoperation
G202.401.03
Enginecoolantpreheatingunit,switchingon
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 ....
G202.401.05
Enginecoolantpreheatingunit,switchingoff
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 ....
G202.651.01
Enginecoolantsystem,ventlineobstructioncheck
G203.000.01
Chargeaircoolantsystemfilling
G203.000.03 G203.000.05
Charge air coolant level check Charge air coolant draining
G203.000.07
Chargeaircoolantsampleextractionandanalysis
G203.051.01
Chargeaircoolantpumpreliefborecheck
G203.551.01
Chargeaircoolantsystem,ventlineobstructioncheck
G205.051.01
Enginecoolantcooler,externalelementcontaminationcheck
G205.051.03
Chargeair coolant cooler, external element contamination check
G208.101.01
Breather valve opening
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 .....
G208.101.03
Breather valve closing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 ......
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 ... . . . . . . . . . . . . . . . . . . . . . . . . . .62 . . . . . . . . . . . . . . . . . . . . . . . .62 .
15345/20 E 00–05
Section
Task Description
G213.051.01
Generatordrive,drivebeltconditionandtensioncheck
G213.051.05
Generatordrivebeltinstallation/replacement
G213.051.08
Generator condition check
G231.051.01
Engine mount security check
G231.051.03
Enginemountresilientelementcheck
G250.000.01
Drivesystem(drivingend)securitycheck
G252.051.01
Coupling condition check
G303.000.01
Compressedairsystemcondensatedraining
G303.000.03
Compressedairsystem,operatingpressurecheck
G307.001.01
Protective device check
G
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 .....
G309.001.01
Battery check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 .....
G309.001.03
Battery filling
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 .....
G309.001.05
Battery charge state check
G364.050.01F
uel supply check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ......
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ......
G364.200.01
Fuelsupplysystem,shut-offvalveclosing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ....
G364.200.03
Fuelsupplysystem,shut-offvalveopening
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ....
G364.200.05
Fuelsupplysystem–fillingintakelinetoengine
G365.000.01
Exhaustsystemcondensatedraining
G365.000.03
Exhaustsystemdrainobstructioncheck
G500.000.01
Enginecontrolsystemswitchingon
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 .....
G500.000.03
Enginecontrolsystemswitchingoff
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 .....
G500.000.07
Enginecontrolsysteminitialoperation
G500.000.09
Engine wiring check
G510.000.01
Monitoringsystem,equipmentfunctioncheck
G510.070.01
Monitoring equipment lamp test
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 .....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 ...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 .....
Section
G
Task Description
15345/20 E 00–05
Task Description
Section
G
Page
1
G000.000.01 Engine Sta rt Disa bling Switch off power supply for Engine Control System at control panel / master switch. Disconnect battery. Shut off fuel supply to engine (G364.000.01). Attach “Danger” sign to control panel / master switch.
G000.000.03 Engine St art Re lease Remove “Danger” sign from control panel / master switch. Connect battery. Open fuel supply to engine (G364.000.03). Switch on power supply for Engine Control System at control panel / master switch.
G000.000.05 Barring Eng ine Man ually Special tools: Engine barring tool No. F6 555 766 Disable engine start (G000.000.01). Install engine barring tool (G030.001.001). Attach ratchet to engine barring tool. Bar engine manually. Note: Apart from the normal compression resistance, there should be no abnormal resistance.
Remove ratchet. Remove engine barring tool (G030.001.03). Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 2
G000.000.07 Barring Engine with Starting System DANGER Unguarded rotating and moving engine components can cause injury. Risk of fatal injury! After working on the engine, check that all protective devices have been reinstalled and all tools removed from the engine. Before barring or starting the engine, ensure that nobody is in the danger zone.
Disconnect plug-in connection (X4) from ECU. Engine start (engine barring) by pressing start button – see G000.000.09. Note: Engine start is automatically interrupted after approx. 5 seconds. If necessary, repeat engine start after approx. 10 seconds.
Screw plug-in connection (X4) to ECU – see G508.000.01.
G000.000.09 Engine Starting DANGER Unguarded rotating and moving engine components can cause injury. Risk of fatal injury! After working on the engine, check that all protective devices have been reinstalled and all tools removed from the engine. Before barring or starting the engine, ensure that nobody is in the danger zone.
When the preparatory work has been carried out in accordance with the Operating Instructions (Section C), the engine can be restarted. Note: Always start the engine under no-load conditions.
Carry out engine start procedure. Do not actuate starter for longer than max. 10 seconds. Before repeating a start attempt, wait at least 20 seconds so that the starter cools down. Do not increase engine speed until oil pressure is displayed. Note: If the engine oil pressure is not built up within the time specified in Engine Monitoring, the engine is shut down by the Engine Control System.
Determine cause and rectify.
15345/20 E 00–05
Task Description
Section
G
Page
3
G000.000.11 Engine Warm-up Procedure Operate the engine with load increasing as slowly as possible until an engine coolant temperature of 40 °C has been reached. Note: Operate the engine at full load only after coolant has reached a temperature of 40 C.
G000.000.13 Engine Speed Check Check idle and full-load speeds.
G000.000.15 Engine Pre ssure Chec ks Check engine oil pressure. Specified values (A000.000.21)
G000.000.17 Engine Temperature Checks Check engine coolant temperature. Specified values (A000.000.21)
G000.000.19 Engine Running Noise Check Run engine at idling speed. Apart from the usual running noises, no abnormal sounds must be heard.
G000.000.21 Engine and External Lines Leak Check DANGER Exhaust gases in closed areas are harmful to health. Risk of poisoning! Ensure that engine room is well ventilated. Repair leaking exhaust pipework immediately.
Run engine under load. Check engine and all pipework for leaks. If leaks are found, shut down engine. When the engine has cooled, rectify the cause. Note: Never tighten lines when under pressure.
15345/20 E 00–05
Section Page
Task Description
G 4
G000.000.23 Engine Shutdown Note: Never shut down engine directly from full-load operation, as this may result in overheating and wear of the engine components.
Before shutting down the engine, run the engine at idling speed until falling and then constant temperatures are indicated. Press engine Shutdown button on driver’s console.
G000.000.25 Emergency Shu tdown Press Emergency Shutdown button on driver’s console.
G000.000.27 Attachments Security Check Exhaust system (G146.000.01) PTO system, driving end (G250.000.01) Engine (G231.051.01)
G000.000.29 Attachments, Hoses a nd Hose Connections Check Check all hoses and hose connections on the engine for condition and leaks. Immediately replace hoses showing signs of scuffing, aging or cracking.
15345/20 E 00–05
Task Description
Section
G
Page
5
G000.000.33 Cylinder Chamber Endoscopic Examination Note: For engines in service, if possible carry out a combustion chamber endoscopic examination after operation under load. Use an endoscope with an adequate light rating and a prism which pivots 95 (5) (total viewing angle 140 ), see –No. 1–.
If an endoscope with pivoting prism is not available, individual endoscopes with prism settings of, 045 and 90 are required, see –No.II–.
Max. possible diameter (a): 16 mm.
Before the endoscopic examination: Remove injector (G075.051.01). Bar engine with starting system (G000.000.07). Disable engine start (G000.000.01). Use engine barring tool to turn engine until, for the respective cylinder, – the piston is at BDC for cylinder liner inspection. – the piston is at a position which permits unobstructed and exact inspection of components for inspecting piston crown and cylinder head lower side and valves. – all valves are open or closed for inspection of valves and valve seats.
Endoscopic examination: Connect endoscope to light source (4) and insert it through the cylinder head (fuel injector bore) to the combustion chamber. Use the focussing device (2) to focus the eyepiece (1) and adjuster ring (3) to align the prism (5) with the area under inspection. Visually assess the cylinder liners, piston crowns, underside of the cylinder heads and valves. To do this, rotate the endoscope through 360 ° in each case and set the prism accordingly.
15345/20 E 00–05
Section Page
Task Description
G 6
Assessment Cylinder liners are OK when: – the honing pattern is clearly visible. – no or only locally limited polished areas are evident in the honing structure. – no or only minor scoring is evident (minor scoring can be caused during piston installation). – no or only minor corrosion is evident (film rust after extended out-of-service periods is possible). Piston crowns are OK when: – injector spray pattern is clearly visible. – only minor carbon or oil deposits are evident. – no or only minor corrosion is evident. Cylinder heads and valves are OK when: – only minor carbon or oil deposits are evident. – no or only minor corrosion is evident. – only minor pitting is evident on valves and valve seats. – the valves close fully. Note: If extensive wear or damage due to mechanical, chemical or thermal action is found, or the inspection results are otherwise suspect: remove the affected cylinder heads and recheck, repair or replace the individual components as necessary.
After the endoscopic examination Remove engine barring tool (G030.001.03). Install injector (G075.051.09). Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
7
G000.000.39 Cleaning Engine Externally WARNING When working with high-pressure and steam jets, never aim at persons, animals, electrical or electronic equipment. Risk of injury and scalding! Wear protective clothing,protective gloves and protective goggles / safety mask.
When removing deposits and / or cleaning, use only non-chemical cleaning agents which do not damage light-alloy, non-ferrous, steel, gray cast iron and elastomers. Clean the engine only at places where there is an appropriate oil separator (environmental protection). Before using the H.P. cleaner or steam jet, read the respective operating instructions, paying particular attention to safety instructions. For cleaning externally with the H.P. jet, use only a flat-jet nozzle.
Carry out external cleaning as follows: Disable engine start (G000.000.01).
To loosen dirt: Spray on a thin coating of cleaning agent and allow 1 to 5 minutes, depending on the degree of contamination, for it to react.
To remove dirt: Use the H.P. jet to spray off the loosened dirt. Note: During exterior engine cleaning with a high-pressure cleaner or steam jet, the jet pressure must not exceed 100 bar (1450 PSI).
Do not go any closer than 20 cm (8 inches) to the object that is being sprayed. The temperature of the cleaning agent must not rise above a max. of 80 °C (176 °F). Note: Moisture penetrating electrical components (temperature transmitter, pressure transmitter, terminal) may lead t o malfunctions and engine failure.
Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 8
G018.101.03 Crankcase Ventilation, Oil Sep arator Check Release clamps, fit rubber sleeve on pipe.
Release clamps, fit rubber sleeves on vent lines.
15345/20 E 00–05
Task Description
Section
G
Page
9
Fit 4 hex screws. Remove oil separator, clamps, washers and spacer sleeves.
Release clamp, turn guide sleeve to withdraw guide sleeve from oil separator and dispose of oil separator.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
15345/20 E 00–05
Section Page
G 10
Task Description
Note: Before installing oil separator, check whether O-ring is installed in oil separator.
Coat guide sleeve and O-ring (see arrow) with ethanol. Press guide sleeve as far as it will go into new oil separator and tighten clamp.
Coat guide sleeve and rubber sleeve with ethanol. Insert guide sleeve (see arrow) into rubber sleeve. Install oil separator, clamp, washer, spacer sleeve and hex screw on bracket, but tighten only lightly.
Align oil separator and fit remaining rubber sleeves on the respective connections. Tighten all clamps.
15345/20 E 00–05
Task Description
Section
G
Page
11
G030.001.01 Engine Barring Tool Installation Special tools: Engine barring tool No. F6 555 766 Disable engine start (G000.000.01). Remove cover from flywheel housing. Engage engine barring tool (1) with ring gear (2) and attach to flywheel housing.
G030.001.03 Engine Barring Tool Removal Remove engine barring tool from flywheel housing. Screw cover to flywheel housing. Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 12
G055.000.01 Valve Gear Oil Supply Check WARNING With the engine running, hot oil emerges at the rocker arm bearings under high pressure. Risk of eye injury and burning! Run engine only when cylinder head covers are installed.
Shut down engine (G000.000.23). Disable engine start (G000.000.01). Remove cylinder head cover (G055.101.01). Check that the rocker arms and the cylinder head cover (inside) are coated with oil. Install cylinder head cover (G055.101.03). Release engine start (G000.000.03).
G055.000.03 Valve Gear Lubrication Note: The oil chambers must be filled with oil during initial operation, extended out-of-service periods and after cleaning valve gear.
Disable engine start (G000.000.01). Remove cylinder head cover (G055.101.01). Fill oil chambers of the valve bridges with oil. Fill oil chambers of the rocker arms and adjusting screws with oil. Install cylinder head cover (G055.101.03). Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
13
G055.050.01 Valve Clearance Check Special tools: – Valve clearance adjusting gauge: – Engine barring tool:
Y2 0010 128 F6 555 766
Note: Check with the valve closed and when coolant temperature does not exceed 40 C.
Disable engine start (G000.000.01). Remove cylinder head cover (G055.101.01). Install engine barring tool (G030.001.01).
Checking valve clearance in two crankshaft positions Bar crankshaft with barring tool in engine direction of rotation until marking TDC-A1 and arrow on flywheel housing are aligned.
Check all valve clearances at two crankshaft positions (firing TDC and overlap TDC, cylinder A1) as per the diagram shown. The crankshaft must be turned in the engine direction of rotation. If the rocker arms are unloaded on cylinder A1, the piston is in firing TDC. 1 = Firing TDC for cylinder A1 If the rocker arms are loaded on cylinder A1, the piston is in overlap TDC. 2 = Overlap TDC for cylinder A1 X = Exhaust valve O = Inlet valve
15345/20 E 00–05
Section Page
Task Description
G 14
Inlet valves: long rocker arm. Exhaust valves: short rocker arm. Valve clearance (A055.050.01). Use feeler gauge to check distance between valve bridge and rocker arm. If deviation from specified value is more than 0.05 mm, adjust valve clearance (G055.050.03). Note: It must be possible to just pull the feeler gauge through the gap.
Remove engine barring tool (G030.001.03). Install cylinder head cover (G055.101.03). Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
15
G055.050.03 Valve Clearance Adjustment (Valve Bridge with Adjusting Screw M16 (Locknut 24 AF)) Note: Before starting adjustment, it is essential to check whether the valve bridges are provided with adjusting screw M16 (locknut 24 AF) or adjusting screws M12 (locknut 19 AF). Then select the appropriate Task Description.
Special tools: – Valve clearance adjusting gauge: – Retaining device: – Engine barring tool:
Y2 0010 128 F6 557 950 F6 555 766
Adjust with the valve closed and when coolant temperature does not exceed 40 C:
Note: Before valve clearance is adjusted, it is essential that the valve bridge be checked.
Disable engine start (G000.000.01). Remove cylinder head cover (G055.101.01). Install engine barring tool (G030.001.01).
Adjusting valve clearance in two crankshaft positions. Bar crankshaft with barring tool in engine direction of rotation until marking TDC-A1 and arrow on flywheel housing are aligned.
15345/20 E 00–05
Section Page
Task Description
G 16
Check all valve clearances at two crankshaft positions (firing TDC and overlap TDC, cylinder A1) as per the diagram shown. The crankshaft must be turned in the engine direction of rotation. If the rocker arms are unloaded on cylinder A1, the piston is in firing TDC. 1 = Firing TDC for cylinder A1 If the rocker arms are loaded on cylinder A1, the piston is in overlap TDC. 2 = Overlap TDC for cylinder A1 X = Exhaust valve O = Inlet valve
Checking valve bridge adjustment Use feeler gauge to determine distance between valve bridge and rocker arm. Note: It must be possible to just pull the feeler gauge through the gap.
Place feeler gauge with determined value between valve bridge and valve stem (B). Using a second feeler gauge, measure distance between opposite valve stem and valve bridge (A). A feeler gauge thicker / thinner by more than 0.05 mm must not fit. The valve bridge must be adjusted if deviation from determined value (B) to (A) valve stem end to valve bridge is greater than 0.05 mm.
15345/20 E 00–05
Task Description
Section
G
Page
17
Adjusting valve bridge
CAUTION To release the locknut, the valve bridge must be held firmly with the retaining device, otherwise the valves will be deformed. Install retaining device. Insert locating pin of retaining device into oil bore of valve bridge. Note: The locating pin can be inserted into the valve bridge oil bore only when the valves are closed / unloaded.
Release locknut.
15345/20 E 00–05
Section Page
G 18
Task Description
Withdraw locating pin of retaining device from oil bore of valve bridge.
Place a feeler gauge of determined distance between valve bridge and valve stem (A) and (B), e.g. 0.20 mm. The valve bridge must be adjusted so that both feeler gauges can just be pulled through. Hold adjusting screw securely in position with Allen key and fit locknut by hand on valve bridge. Insert locating pin of retaining device into oil bore of valve bridge. Note: The locknut and adjusting screw must be free to move.
Use torque wrench to tighten locknut, holding adjusting screw firmly with Allen key. The adjusting screw must not turn. Tightening torque = 90 Nm + 9 Nm Lubricant = Engine oil Withdraw locating pin of retaining device from oil bore of valve bridge.
15345/20 E 00–05
Task Description
Section
G
Page
19
Again check valve bridge adjustment. Remove retaining device.
CAUTION Before barring the engine, the retaining device must be removed, otherwise with a secured valve bridge the valve gear or retaining device will be damaged.
Valve clearance adjustment Inlet valves: long rocker arm. Exhaust valves: short rocker arm. Valve clearance, see (A055.050.01). Release locknut (1) and slightly unscrew adjusting screw (2) with Allen key. Insert feeler gauge between valve bridge and rocker arm. Set adjusting screw so that feeler gauge just passes through gap when locknut is tightened. Tighten locknut with torque wrench, holding adjusting screw firm. Note: The locknut and adjusting screw must be free to move.
Tightening torque = 90 Nm + 9 Nm Lubricant = Engine oil Recheck valve clearance. Remove engine barring tool (G030.001.03). Install cylinder head cover (G055.101.03). Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 20
G055.050.03 Valve Clearance Adjustment (Valve Bridge with Adjusting Screw M12 (Locknut 19 AF)) Note: Before starting adjustment, it is essential to check whether the valve bridges are provided with adjusting screw M16 (locknut 24 AF) or adjusting screws M12 (locknut 19 AF). Then select the appropriate Task Description.
Special tools: – Valve clearance adjusting gauge: – Engine barring tool:
Y2 0010 128 F6 555 766
Adjust with the valve does not exceed 40 C: closed and when coolant temperature
Note: Before valve clearance is adjusted, it is essential that the valve bridge be checked.
Disable engine start (G000.000.01). Remove cylinder head cover (G055.101.01). Install engine barring tool (G030.001.01).
Adjusting valve clearance in two crankshaft positions Bar crankshaft with barring tool in engine direction of rotation until marking TDC-A1 and arrow on flywheel housing are aligned.
Check all valve clearances at two crankshaft positions (firing TDC and overlap TDC, cylinder A1) as per the diagram shown. The crankshaft must be turned in the engine direction of rotation. If the rocker arms are unloaded on cylinder A1, the piston is in firing TDC. 1 = Firing TDC for cylinder A1 If the rocker arms are loaded on cylinder A1, the piston is in overlap TDC. 2 = Overlap TDC for cylinder A1 X = Exhaust valve O = Inlet valve
15345/20 E 00–05
Task Description
Section
G
Page
21
Checking valve bridge adjustment Use feeler gauge to determine distance between valve bridge and rocker arm. Note: It must be possible to just pull the feeler gauge through the gap.
Place feeler gauge with determined value between valve bridge and valve stem (B). Using a second feeler gauge, measure distance between opposite valve stem and valve bridge (A). A feeler gauge thicker / thinner by more than 0.05 mm must not fit. The valve bridge must be adjusted if deviation from determined value (B) to (A) valve stem end to valve bridge is greater than 0.05 mm.
15345/20 E 00–05
Section Page
Task Description
G 22
Adjusting valve bridge
CAUTION When releasing the locknut, the valve bridge must be held firmly, as otherwise the valves will be bent. Hold valve bridge (1) firmly in position with open-end wrench and release locknut (2).
Place a feeler gauge of determined distance between valve bridge and valve stem (A) and (B), e.g. 0.20 mm. The valve bridge must be adjusted so that both feeler gauges can just be pulled through. Hold adjusting screw securely in position with Allen key and fit locknut by hand on valve bridge. Note: The locknut and adjusting screw must be free to move.
15345/20 E 00–05
Task Description
Section
G
Page
23
Using torque wrench, tighten locknut (2); for this purpose hold valve bridge (1) in position with open-end wrench. Tightening torque = 35 Nm + 5 Nm Lubricant = Engine oil
Again check valve bridge adjustment.
15345/20 E 00–05
Section Page
Task Description
G 24
Valve clearance adjustment Inlet valves: long rocker arm. Exhaust valves: short rocker arm. Valve clearance, see (A055.050.01). Release locknut (1) and slightly unscrew adjusting screw (2) with Allen key. Insert feeler gauge between valve bridge and rocker arm. Set adjusting screw so that feeler gauge just passes through gap when locknut is tightened. Tighten locknut with torque wrench, holding adjusting screw firm. Note: The locknut and adjusting screw must be free to move.
Tightening torque = 90 Nm + 9 Nm Lubricant = Engine oil Recheck valve clearance. Remove engine barring tool (G030.001.03). Install cylinder head cover (G055.101.03). Release engine start (G000.000.03).
G055.101.01 Cylinder Head Cover Removal WARNING With the engine running, hot oil emerges at the rocker arm bearings under high pressure. Risk of eye injury and burning! Run engine only when cylinder head covers are installed.
Disable engine start (G000.000.01). Remove screws. Remove cylinder head cover from cylinder head.
15345/20 E 00–05
Task Description
Section
G
Page
25
G055.101.03 Cylinder Head Cover Installation Clean mating faces. Check that profile gasket in cylinder head cover is in perfect condition, replace if necessary. Place cylinder head cover on cylinder head. Insert screws with washers and tighten with torque wrench. Tightening torque = 42 Nm Lubricant = Engine oil Release engine start (G000.000.03).
G073.051.07 High-Pressure Pump, Relief Bor e Obstruction Check Check relief bore for oil and fuel discharge (visual inspection). Clean the bore if it is contaminated. Note: Replace H.P. fuel pump if oil and/or fuel emerges from the relief bore.
15345/20 E 00–05
Section Page
Task Description
G 26
G075.051.01 Injector Removal WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel. Note: The fuel injectors can only be replaced completely, as the injection nozzle can only be replaced at MTU.
Special tools: – Extractor sleeve for injector: – Extractor:
F3 0377 769 F6557991
Disable engine start (G000.000.01). Shut off fuel supply to engine (G364.000.01). Remove cylinder head cover (G055.101.01). Remove fuel return line on cylinder head and on fuel collecting line. Note: Fuel must not penetrate the cylinder chamber.
15345/20 E 00–05
Task Description
Section
G
Page
27
Release the cable terminal threaded connection on the injector and remove cable terminals.
Remove screw (1) together with hold-down clamp (2).
Unscrew H.P. fuel line (2) from injector (1) and connector (limiting valve) (3) and remove H.P. line. Note: The H.P. line must not be bent.
15345/20 E 00–05
Section Page
G 28
Task Description
Place extractor sleeve section 1 (4) on injector (1). Fit section 2 (2) over section 1 and turn to correct position – see next illustration. Secure section 2 with hex nut (3).
Starting point for section 2 (2) is position “a” (2 o’clock) End point is position “b” (12 o’clock).
Screw threaded rod (3) into extractor sleeve (5) and secure with hex nut (4). Place extractor (2) on cylinder head. Turn nut (1) clockwise to withdraw injector. Remove special tool. Remove injector manually.
15345/20 E 00–05
Task Description
Section
G
Page
29
Remove CE support ring (1) from injector or use wire hook to remove from cylinder head. Remove O-rings (2) from injector. Cover all connections and bores, or seal with suitable plugs. Note: Fuel must not penetrate the cylinder.
G075.051.05 Injector Replacement WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel.
Remove injectors (G075.051.01). Install injectors (G075.051.09). Note: The fuel injectors for replacement can be ordered from MTU.
G075.051.09 Injector Installation WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel.
Special tools: – Press-fitting lever for injector: – Press-fitting sleeve for injector: – Lever:
15345/20 E 00–05
F6 557 952 F3 0378 403 F6 555 197
Section Page
G 30
Task Description
Coat new O-rings with petroleum jelly and fit on injector.
Check sealing surface on cylinder head (heat protection sleeve) for contamination, clean if necessary. Fit new CE Ring (2) with grease on injector (1).
Ensure that CE ring is correctly positioned.
15345/20 E 00–05
Task Description
Section
G
Page
31
Note: Before installation, remove all plugs and covers.
Insert fuel injector (1) into cylinder head, ensuring the H.P. line connection is correctly aligned. Fit press-fitting sleeve (2).
Lock press-fitting tool (1) between pushrods. Release palm grip (3) and move pressure element (2) to correct position for press-fitting sleeve. Secure palm grip and press injector (4) with press-fitting tool into cylinder head. Remove press-fitting tool.
Install hold-down clamp (2), positioning correctly, and fit hex screw (1) by hand.
15345/20 E 00–05
Section Page
G 32
Task Description
Tighten screw of hold-down clamp with torque wrench. Tightening torque: 5 Nm to 10 Nm Lubricant = Engine oil
Coat new O-ring (2) with petroleum jelly and fit on H.P. line (3). Install H.P. line (3) at injector (1) and connector (limiting valve) (4). Note: The H.P. line must not be bent. Ensure that the installation position is correct.
Using torque wrench, tighten H.P. line (2) at injector (1) and connector (limiting valve) (3). Tightening torque: 5 Nm to 10 Nm Lubricant = Engine oil Note: The H.P. line must not be bent. Ensure that the installation position is correct.
15345/20 E 00–05
Task Description
Section
G
Page
33
Tighten hex screw of hold-down clamp with torque wrench. Tightening torque: 100 Nm + 10 Nm Lubricant = Engine oil
Using torque wrench, tighten threaded connection of H.P. line at injector (1) and connector (limiting valve) (2). Tightening torque: 100 Nm + 10 Nm Lubricant = Engine oil Note: The H.P. line must not be bent. Ensure that the installation position is correct.
15345/20 E 00–05
Section Page
G 34
Task Description
Fit cable terminals below the screws on injector and tighten. Tightening torque: 1.0 Nm +/– 0.2 Nm Install cylinder head cover (G055.101.03).
Attach fuel return line between cylinder head and manifold and tighten. Open fuel supply to engine (G364.000.03). Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
35
G080.000.03 Fuel System Filling WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel.
Special tools: Filling device: B8 0144 852 On initial operation/restart or after a fuel filter change, the L.P. fuel system must be refilled. Disable engine start (G000.000.01). Fill L.P. fuel system. Remove flushing line (1) from the H.P. pump (3) and release from filter block (2). Connect the fuel return hose of the filling device to the H.P. pump (3). Connect the filling device fuel supply to connection (P) of the filter block. NOTE: When filling, a fuel pressure of between 0.5 and 1.5 bar must be achieved.
The fuel system is filled by the hand pump until bubble-free fuel is seen to emerge in the fuel return hose.
Filling device Fuel supply (1) Fuel return (2)
15345/20 E 00–05
Section Page
Task Description
G 36
Remove fuel return hose from the H.P. pump (3). Screw flushing line (1) onto the H.P. pump (3) and filter block (2) and tighten. Remove the filling device fuel supply from connection (P) of the filter block. Seal filling connection (P) with blanking plug and tighten. Release engine start (G000.000.03). The H.P. system is filled when the engine is started.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
G080.000.05 Fuel System, Fuel Delivery Pump Supply Check Connect pressure gauge before fuel delivery pump. Run engine at full load and read off pressure gauge. Specified value, see (A000.000.21). Remove pressure gauge.
G083.051.03 Fuel Duplex Filter Replacement WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel.
Special tools: Strap wrench F3 0006 199
15345/20 E 00–05
Task Description
Section
G
Page
37
Remove filter and dispose of in accordance with local regulations. Clean sealing surface at connector. Check sealing ring of new filter and moisten with fuel. Install filter and tighten by hand. Replace second filter in same way.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
15345/20 E 00–05
Section Page
Task Description
G 38
G083.101.01 Fuel Pref ilter Primi ng Fuel prefilter not supplied by MTU. See Operating Instructions of Plant Manufacturer.
G083.101.03 Fuel Prefilter, Water and Conta minants Drainin g Fuel prefilter not supplied by MTU. See Operating Instructions of Plant Manufacturer.
G083.101.09 Fuel Prefilter, Element and Gask et Replacement WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel.
Fuel prefilter not supplied by MTU. See Operating Instructions of Plant Manufacturer.
G083.101.15 Fuel Prefi lter Clean ing WARNING Fuels are combustible. Fire hazard! When working on the fuel system: No open flame, no electrical sparks. Do not spill fuel.
Close fuel supply. Remove nuts from filter head. Remove filter bowl and drain fuel into a suitable container. Remove securing nut for filter element and remove filter element from below.
15345/20 E 00–05
Task Description
Section
G
Page
39
Using a clean brush, flush out filter element in clean fuel. Flush out filter bowl with clean fuel. Insert filter insert in filter bowl and secure with the nut. Insert new sealing ring in groove in filter head. Mount filter bowl taking care not to damage sealing ring. Tighten nuts diagonally and evenly. Fuel supply opening.
G101.011.01 Exhaust Turbocharger, Engine Operation in Event of Turbocharger Failure In the event of turbocharger failure, determine the cause and assess whether the engine can continue in operation without risk. If, in the event of turbocharger failure (e.g. if rotor is seized), the engine must continue in operation, run the engine only under partial load. Run the engine in this condition only until it is possible to replace or repair the turbocharger.
G101.011.05 Exhaust Turbocharger Connections Check Check exhaust connections for leaks.
15345/20 E 00–05
Section Page
G 40
Task Description
Check oil supply and return lines for leaks.
15345/20 E 00–05
Task Description
Section
G
Page
41
G120.000.03 Intake Air System , Intake Si de Leak and Damage Check Check intake side of engine for condition and leaks with the engine running.
G120.000.05 Intake Air System, Intake Depression Check Connect U-pipe pressure gauges to turbocharger air intake housings. Run engine at full load and read off indicated pressures. Specified value, see (A000.000.21). Remove U-pipe pressure gauges.
G120.000.07 Intake Ai r Syst em Che ck Check that cover is removed. Check for cleanliness. Disable engine start (G000.000.01). Remove guard and loose material on intake housing or air filter. Release band clamp. Remove air filter from intake housing. Mount new air filter on intake housing. Tighten band clamp. Release engine start (G000.000.03).
G121.051.01 Air Fil ter Rep lacement Disable engine start (G000.000.01). Remove guard and loose material on intake housing or air filter. Remove contamination indicator (4). Release clamp (2). Remove air filter (3) and dispose of in accordance with local regulations. Clean connection on air flow control flap housing (1). Install new air filter with clamp. Install contamination indicator with reset signal ring (G121.052.01). Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 42
G121.052.01 Air Filter, Contamination Indicator Positio n Check Check Check position of signal ring (1) (visual check). If signal ring is fully visible, replace air filter (G121.051.01).
Reset Press reset button (2) to return signal ring to normal position.
G124.051.01 Charge Air Manifold , Drain Wa ter Discha rge and Obstru ction Chec k WARNING Engine noise above 85 dB(A). Risk of damage to hearing! Wear ear protectors.
Engine coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Coolant discharge check If the coolant is continuously discharged and the coolant level falling, the intercooler is leaking. If a leaking intercooler cannot be repaired immediately, before starting the engine: – Remove injection nozzles (G075.051.01). – Bar engine manually (G000.000.05). – Bar engine with starting system (G000.000.07) and blow out combustion chambers. Note: If the intercooler is leaking, activate engine only in an emergency.
Obstruction check Note: Check drain bore on engine A and B sides.
With the engine running, oil-containing air must emerge at the drain bore.
15345/20 E 00–05
Task Description
Section
G
Page
43
G124.051.03 Charge Air Manifold Drain Cleaning CAUTION Compressed air is air compressed under pressure. Risk of injury! If compressed air is used for blowing out or blow-drying components, always wear protective goggles or safety mask. Compressed air must not be aimed at parts of the body. The pressure must not exceed 3.0 bar.
Disable engine start (G000.000.01). Clean drain bore, blow out with compressed air and check for obstructions. Note: Clean and check drain bore on engine A and B sides.
Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 44
G140.000.01 Exhaust Syste m Chec k Check engine exhaust system (visual inspection) for leaks and damage.
G140.000.03 Exhaust System Security Check When the engine is cold, check tightness of securing screws by torque wrench application.
G140.000.05 Exhaust System, Exhaust Gas Colour Check Exhaust gases light grey: good combustion. Exhaust gases black: incomplete combustion. Exhaust gases blue: excessive engine oil in combustion chamber. Exhaust gases white: unburnt fuel.
G140.000.07 Exhaust Syste m Chec k Check that cover is removed. Check for cleanliness.
G140.000.09 Exhaust System, Exhaust Backpressure Check Connect U-pipe pressure gauge to exhaust manifold. Run engine at full load and read off indicated pressures. Specified value, see (A000.000.21). Remove U-pipe pressure gauges.
G140.000.11 Exhaust System Drain Obstruction Check Check and drain exhaust system. (If drain is provided.)
G146.000.01 Exhaust System , Security and Exha ust Manifo ld Insulat ion Check s Check tightness of the exhaust system securing screws (after engine) by torque wrench application and the insulation for damage by visual inspection.
G172.051.09 Starter Con dition Che ck Disable engine start (G000.000.01). Check starter for mechanical damage. Check security of starter securing screws. Check security and condition of all cable connections. Check all electric cables for damage. Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
45
G180.000.01 Engine Oi l Lev el Che ck Checking before starting engine Withdraw dipstick from guide tube and wipe. Carry out oil level check. Engine oil must be between Min. and Max. marks. If necessary, top up oil to Max. mark. Insert dipstick in guide tube.
Checking after engine shutdown Remove the oil dipstick from the guide tube 5 minutes after engine shutdown. Engine oil must be between Min. and Max. marks. If necessary, top up oil to Max. mark. Insert dipstick in guide tube.
G180.000.03 Engine Oil Sy stem Filli ng Note: Always use MTU-approved engine oil, see MTU Fluids and Lubricants Specification.
Turn cover counterclockwise until the cover of the oil filler neck can be removed. Pour engine oil in at oil filler neck up to Max. mark on oil filler neck. Start engine and run at idle for approx. 1 to 2 minutes. Shut down engine and after approx. 5 minutes withdraw dipstick from guide tube and wipe. Carry out oil level check. Engine oil must be between Min. and Max. marks. If necessary, top up oil to Max. mark. Note: Do not fill engine oil above the Max. mark.
Insert dipstick in guide tube. Reinstall oil filler neck cover.
15345/20 E 00–05
Section Page
Task Description
G 46
G180.000.04 Engine Oil Sample Extraction and Analysis DANGER Engine oil is hot and can contain combustion residues which are harmful to health. Risk of injury! Wear protective gloves. Avoid extended and intensive contact with skin. Do not inhale oil vapour.
Open shut-off cock with engine running and engine at operating temperature. Drain approx. 2 litres of engine oil into a container in order to flush out the oil sludge in the shut-off cock. Drain approx. 1 litre of engine oil coolant into a clean container. Using equipment and chemicals from the MTU Test Kit, inspect the engine oil for dispersion capability (spot test), coolant content and fuel dilution – see Publication for MTU Test Kit.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
G180.000.05 Engine Oil Change Disable engine start (G000.000.01). Drain engine oil (G180.000.07). Replace engine oil filter (G183.052.03). Pour in new engine oil (G180.000.03). Release engine start (G000.000.03). Note: After each engine oil change and filter replacement, bar the engine with the starting system (G000.000.07).
15345/20 E 00–05
Task Description
Section
G
Page
47
G180.000.07 Engine Oil Dra ining DANGER Engine oil is hot and can contain combustion residues which are harmful to health. Risk of injury! Wear protective gloves. Avoid extended and intensive contact with skin. Do not inhale oil vapour.
Note: Drain engine oil with the engine at operating temperature.
Provide a suitable container in which to collect and dispose of the engine oil. Drain engine oil from the oil pan at the oil drain plug. Install oil drain plug with a new sealing ring.
Drain remaining oil from equipment carrier. Install oil drain plug with a new sealing ring.
15345/20 E 00–05
Section Page
Task Description
G 48
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
G180.000.09 Corrosion Inhibitor Oil Filling Note: Always use only approved corrosion inhibitor oil – see MTU Fluids and Lubricants Specifications.
Fill engine with corrosion inhibitor oil in same way as engine oil (G180.000.03).
G180.000.11 Corrosion Inhibitor Oil Draining DANGER Engine oil is hot and can contain combustion residues which are harmful to health. Risk of injury! Wear protective gloves. Avoid extended and intensive contact with skin. Do not inhale oil vapour.
Drain corrosion inhibitor oil in same way as engine oil (G180.000.07). Note: Drain the corrosion inhibitor oil with the engine at operating temperature.
G183.052.03 Engine Oil Filter Replacement DANGER Engine oil is hot and can contain combustion residues which are harmful to health. Risk of injury! Wear protective gloves. Avoid extended and intensive contact with skin. Do not inhale oil vapour.
Special tools: Oil filter key F3 0379 104
15345/20 E 00–05
Task Description
Section
G
Page
49
Disable engine start (G000.000.01). Use oil filter key to unscrew. Drain remaining oil out of the filters into a container. Clean sealing surface at connector. Check sealing ring of new engine oil filter and coat with oil. Install new engine oil filter and tighten by hand. Replace other engine oil filters in same way. Release engine start (G000.000.03).
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
15345/20 E 00–05
Section Page
Task Description
G 50
G183.101.01 Centrifugal Oil Filter Cleaning DANGER Engine oil is hot and can contain combustion residues which are harmful to health. Risk of injury! Wear protective gloves. Avoid extended and intensive contact with skin. Do not inhale oil vapour.
Disable engine start (G000.000.01). Release nut. Release band clamp.
Remove band clamp. Remove housing cover. Remove sealing ring.
15345/20 E 00–05
Task Description
Section
G
Page
51
Carefully remove complete rotor from housing. Drain oil.
Note: The rotor must not be clamped in a vice.
Release knurled nut on rotor cap. Press out rotor lower section downwards.
Carefully remove rotor cap from standpipe. Remove sealing ring.
15345/20 E 00–05
Section Page
Task Description
G 52
CAUTION Compressed air is air compressed under pressure. Risk of injury! If compressed air is used for blowing out or blow-drying components, always wear protective goggles or safety mask. Compressed air must not be aimed at parts of the body. The pressure must not exceed 3.0 bar.
Remove insertion sleeve. Assess the layer thickness and weight of the oil residues on the sleeve and compare to the values noted during the previous check. Note: Layer thickness max 20 mm (approx. 1800 gr.)
If the two values deviate greatly, the oil must be changed. Perform the next oil change earlier than scheduled. Clean rotor cap, standpipe and rotor base. Wash components, blow out with compressed air. Insert new insertion sleeve.
Assemble rotor cap and standpipe. Insert new sealing ring and fit on rotor lower section. Tighten knurled nut.
15345/20 E 00–05
Task Description
Section
G
Page
53
Insert rotor in housing lower section. Fit new sealing ring. Mount housing cover. Tighten nut. Tighten band clamp. Release engine start (G000.000.03). When the engine is again started, check the centrifugal oil filters for leaks.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
15345/20 E 00–05
Section Page
Task Description
G 54
G202.000.01 Engine Coolant System Filling WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Open breather valve (G208.101.01), so that the air can escape from the engine when the coolant system is filled.
Note: Always use only treated coolant in accordance with MTU Fluids and Lubricant Specifications. Never pour cold coolant into a hot engine. If, in an emergency, untreated water is used to top up the coolant system, the coolant concentration must be checked and rectified at the earliest opportunity.
Connect suitable hose to the drain valve (arrow). Open drain valve and pour in engine coolant via the hose. Close drain valve. Check engine coolant level (G202.000.03). Close breather valve (G208.101.03). Run engine a number of minutes at idling speed. Check engine coolant level (G202.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
55
G202.000.03 Engine Coolant Level Check Note: The Min. coolant level is automatically monitored by the engine control system.
Via level sensor Switch on engine control system (G500.000.01) and check indicator.
WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Note: Always use only treated coolant in accordance with MTU Fluids and Lubricant Specifications. Never pour cold coolant into a hot engine. If, in an emergency, untreated water is used to top up the coolant system, the coolant concentration must be checked and rectified at the earliest opportunity.
Open breather valve of coolant expansion tank (G208.101.01). If fluid is too low, add only treated coolant – see (G202.000.01). Close breather valve (G208.101.03).
15345/20 E 00–05
Section Page
Task Description
G 56
G202.000.05 Engine Coolant Sample Extraction and Analysis WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Disable engine start (G000.000.01). Open drain valve. Drain a small quantity of coolant to flush the drain point. Drain approx. 1 litre of engine coolant into a clean container. Close drain valve. Check engine coolant level (G202.000.03). Using the equipment and chemicals in the MTU Test Kit, examine the coolant for: – antifreeze – corrosion inhibitor – pH value See MTU Test Kit instructions. Change engine coolant according to the coolant operating times in the Fluids and Lubricants Specification A001061. Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
57
G202.000.07 Drain Eng ine Co olant WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Disable engine start (G000.000.01). Note: Drain engine coolant when engine has cooled.
Open breather valve (G208.101.01). Provide a suitable container to collect and dispose of the coolant. Open lower drain valve on coolant inlet elbow and drain coolant. Drain residual coolant from engine via the upper drain point on crankcase (A and B sides). Seal all drain points. Close breather valve (G208.101.03). Dispose of engine coolant.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
15345/20 E 00–05
Section Page
Task Description
G 58
G202.000.09 Engine Co olant Cha nge WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Drain engine coolant (G202.000.07). Fill engine coolant system (G202.000.01).
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
G202.051.01 Engine Coolant Pump Relief Bore Check Check relief bore for oil and coolant discharge (visual inspection). Clean the relief bore if it is dirty. Note: If oil and / or coolant emerge from the relief bore, repair the engine coolant pump.
G202.400.01 Engine Coolant Preheating Switch on preheating unit. Check function of coolant circulating pump. Preheat engine coolant to preheat temperature (A000.000.21).
15345/20 E 00–05
Task Description
Section
G
Page
59
G202.401.01 Engine Coolant Preheating Unit Initial Op eration Engine coolant preheating unit not supplied by MTU. Carry out tasks as specified by Manufacturer.
G202.401.03 Engine Coolant Preheating Unit, Switching On Switch on preheating unit. Check function of coolant circulating pump. Carry out tasks as specified by Manufacturer.
G202.401.05 Engine Coolant Preheating Unit, Switch ing Off Switch off preheating unit. Carry out tasks as specified by Manufacturer.
G202.651.01 Engine Coolant Sy stem, Vent Line Obs truction Check
CAUTION Compressed air is air compressed under pressure. Risk of injury! If compressed air is used for blowing out or blow-drying components, always wear protective goggles or safety mask. Compressed air must not be aimed at parts of the body. The pressure must not exceed 3.0 bar.
Remove vent lines and blow out with compressed air. Install vent lines.
G203.000.01 Charge Air Coolant System Filling Note: Always use treated engine coolant corresponding to MTU Fluids and Lubricants Specification.
Open breather valve (G208.101.01). Pour in treated engine coolant via filler neck. Check charge air coolant level (G202.000.03). Close breather valve (G208.101.03). Run engine a number of minutes at idling speed. Check charge air coolant level (G202.000.03).
15345/20 E 00–05
Section Page
Task Description
G 60
G203.000.03 Charge Air Coolant Level Check Note: The “Min.” coolant level is automatically monitored by the Engine Control System.
Via level sensor Switch on engine control system and check display. Manual coolant level checking see Alternator Manufacturer’s operating instructions.
WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Open breather valve of coolant expansion tank (G208.101.01). Coolant expansion tank is not supplied by MTU. In event of drop in coolant level only fill with treated engine coolant. Note: Never pour cold coolant into a hot engine. If, in an emergency, untreated water is used to top up the coolant system, the coolant concentration must be checked and rectified at the earliest opportunity.
Close breather valve (G208.101.03).
15345/20 E 00–05
Task Description
Section
G
Page
61
G203.000.05 Charge Air Coolant Draining WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Disable engine start (G000.000.01). Note: Drain engine coolant when engine has cooled.
Open breather valve (G208.101.01). Provide a suitable container to collect and dispose of the coolant. Drain coolant via drain points from cooling system – see Alternator Manufacturer’s Operating Instructions. Seal all drain points. Dispose of coolant.
Disposal of Hazardous Materials Fluids and lubricants (e.g. oils, greases, treated engine coolant, fuels), cleaning agents and numerous auxiliary materials are an environmental hazard and therefore constitute hazardous materials. When disposing of these hazardous materials, always follow the manufacturer’s instructions, general environmental protection regulations and local legal specifications. Under no circumstances must even small amounts of hazardous materials be allowed to drain into water, or be discarded or disposed of outdoors. Leaked hazardous materials must immediately be absorbed with suitable bonding agents and disposed of in accordance with regulations in appropriate vessels. The contents of these containers must be specified.
G203.000.07 Charge Air Coola nt Sample Extraction and Analysis Disable engine start (G000.000.01). Open blanking plug. By means of the blanking union, drain approx. 1 litre coolant into a clean container. Close blanking plug. Check charge air coolant level (G203.000.03). Using the equipment and chemicals in the MTU Test Kit, examine the coolant for: – antifreeze – corrosion inhibitor – pH value See MTU Test Kit instructions. Change engine coolant according to the coolant operating times in the Fluids and Lubricants Specification A001061. Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 62
G203.051.01 Charge Air Coolant Pump Relief Bore Check Check relief bore for oil and coolant discharge (visual inspection). Clean the relief bore if it is dirty. Note: If oil and / or coolant emerge from the relief bore, repair the charge air coolant pump.
G203.551.01 Charge Air Coolan t System, Vent Line Obs truction Check Vent lines not supplied by MTU. Carry out tasks as specified by Manufacturer.
G205.051.01 Engine Coolant Coole r, External Eleme nt Contamin ation Chec k Coolant cooler is not supplied by MTU. Carry out tasks as specified by Manufacturer.
G205.051.03 Charge Air Coolant Coole r, External Elemen t Contamina tion Check Coolant cooler is not supplied by MTU. Carry out tasks as specified by Manufacturer.
15345/20 E 00–05
Task Description
Section
G
Page
63
G208.101.01 Breather Valve Opening WARNING Coolant is hot and under pressure. Risk of injury! Wear protective gloves.
Disable engine start (G000.000.01). Turn breather valve counterclockwise to first stop. Allow pressure to escape. Continue to turn breather valve counterclockwise and remove.
G208.101.03 Breather Valve Closing Check that breather valve is in perfect condition. Clean sealing surfaces. Fit breather valve and turn clockwise as far as it will go. Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 64
G213.051.01 Generator Drive , Drive Belt Con dition an d Tension Check DANGER Unguarded rotating and moving engine components can cause injury. Risk of fatal injury! After working on the engine, check that all protective devices have been reinstalled and all tools removed from the engine. Before barring or starting the engine, ensure that nobody is in the danger zone.
Special tools: V-ribbed belt tension tester
Condition check Disable engine start (G000.000.01). Remove guard plate. Check V-ribbed belts for cracks, oil, overheating and wear; clean or replace as necessary. NOTE: Solvents such as petroleum or benzol must not be used. Sharp-edged objects are not cleaning agents.
Damage pattern of V-ribbed belts. Normal wear. One or two cracks in the rib, measuring approx. 25 mm (1 inch), usually appear after long-term use; the V-ribbed belts can continue to be used.
F2130001 0a
15345/20 E 00–05
Task Description
Section
G
Page
65
The V-ribbed belts must be replaced if the ribs are broken around the entire circumference.
F2130002 0a
The V-ribbed belt must be replaced immediately if the ribbed material has broken through and the ribs are broken around the entire circumference.
F2130003 0a
Tension check Position the V-ribbed belt tension tester on the V-ribbed belt midway between the belt pulleys. Read off the value from the scale.
Settings New V-ribbed belts: 57–70 kg (125–155 lbs) Used V-ribbed belts: 57–70 kg (125–155 lbs)
15345/20 E 00–05
Section Page
Task Description
G 66
If the measured value does not correspond to the specified set value, V-ribbed belt tension must be corrected. Release locknut (2) and securing screws (1). Secure V-ribbed belt with clamping nut (3). Check V-ribbed belt tension. Tighten locknut (2). Tighten securing screws (1). Install guard plate. Release engine start (G000.000.03).
G213.051.05 Generator Driv e Belt Installation / Replacement Disable engine start (G000.000.01). Remove guard plate. Release securing screws (1). Release locknut (2) and clamping nut (3) so that both V-ribbed belts can be removed. Check that V-ribbed belt pulleys are clean; clean if necessary. Fit new V-ribbed belts. Secure V-ribbed belt with clamping nut (3). Set V-ribbed belt tension, see under (G213.051.01). Tighten locknut (2). Tighten securing screws (1). Install guard plate. Release engine start (G000.000.03). Note: After the engine has run for 30 minutes, again check V-ribbed belt tension; readjust if necessary. After the engine has run for 8 hours, again check V-ribbed belt tension; readjust if necessary.
15345/20 E 00–05
Task Description
Section
G
Page
67
G213.051.08 Generator Condition Check Disable engine start (G000.000.01). Remove guard plate. Check generator for mechanical damage. Check security and condition of all cable connections. Check all electric cables for damage. Install guard plate. Release engine start (G000.000.03).
G231.051.01 Engine Mount Security Check Check tightness of all securing screws by torque wrench application.
G231.051.03 Engine Mount Resilient Element Check Check resilient mounts for cracks and deformation (visual inspection). Replace cracked rubber elements. Note: Wipe rubber surfaces with dry cloth only, never clean with organic detergents.
G250.000.01 Drive System (Driving End) Security Check Disable engine start (G000.000.01). Remove guard plates from PTO system, driving end. Check tightness of securing screws of PTO system, driving end, by torque wrench application. Install guard plate (driving end). Release engine start (G000.000.03).
15345/20 E 00–05
Section Page
Task Description
G 68
G252.051.01 Coupling Cond ition Check Disable engine start (G000.000.01). Coupling is not supplied by MTU. Carry out tasks specified by Manufacturer. Release engine start (G000.000.03).
G303.000.01 Compressed Air System Condensate Draining Open drain valves on compressed air system and allow condensate to drain. Note: The pressure drop on the pressure gauge must not be more than approx. 1 bar.
Close drain valves. Drain condensate from compressed air tank in accordance with manufacturer’s specifications.
G303.000.03 Compressed Air System, Op erating Pressure Check Open shut-off valve before pressure gauge. Check compressed air at pressure gauge. Always fill compressed air tank to maximum pressure. Note: Examine compressed air systems regularly; clean and subject them to a pressure test. Observe the local safety regulations.
G307.001.01 Protective Device Che ck Check that all guards are correctly installed on the generator and PTO systems, driving end and free end. Guard plates on PTO system, driving end.
15345/20 E 00–05
Task Description
Section
G
Page
69
G309.001.01 Battery Check WARNING Battery acid is highly caustic and may splash into eyes. During filling or charging, explosive gases may develop. Metal objects between battery terminals cause short-circuiting. Risk of explosion, burning and short-circuiting! No naked flames. No electrical sparks. Do not smoke. Wear rubber gloves, protective goggles and protective clothing. Before starting work, provide clean water for washing. If battery filling gets into eyes, rinse immediately with water and seek medical attention. Do not place metal objects on battery.
The battery is not supplied by MTU. Carry out tasks specified by manufacturer.
G309.001.03 Battery Filling Fill battery with electrolyte or alkaline solution. Carry out tasks specified by manufacturer.
G309.001.05 Battery Charge State Check
Check fluid viscosity and electrolyte level. Carry out tasks specified by manufacturer.
G364.050.01 Fuel Supply Check WARNING Fuels are combustible. Fire hazard! When working on the fuel system: no naked flame no electrical sparks do not smoke do not spill fuel.
Check fuel supply in fuel tank, top up if necessary. Note: A full fuel tank reduces condensation and the growth of bacteria.
G364.200.01 Fuel Supply System, Shut-Off Valve Closing Close shut-off valve in supply line before fuel prefilter.
15345/20 E 00–05
Section Page
Task Description
G 70
G364.200.03 Fuel Supply System, Shut-Off Valve Opening Open shut-off valve in supply line before fuel prefilter.
G364.200.05 Fuel Supply System – Fill ing Intake Line to En gine Clean fuel system and fill with clean fuel.
G365.000.01 Exhaust System Condensate Draini ng system is not supplied by MTU. Carry out Exhaust tasks specified by Manufacturer.
G365.000.03 Exhaust System Drain Obstruction Check Exhaust system not supplied by MTU.
G500.000.01 Engine Control System Switching On Move power supply master switch from “Off” to “On”.
G500.000.03 Engine Control System Switching Off Move power supply master switch from “On” to “Off”.
G500.000.07 Engine Control System Initial Operatio n Contact MTU Service. G500.000.09 Engine Wiring Che ck Disable engine start (G000.000.01). Check all plug-in connection(s) for security and damage at: – Speed, pressure and temperature transmitters – Level sensor – Fuel prefilter Check all mechanical fixtures and electrical connections. – – – – –
Injection pumps Battery Turbocharger control Starter Generator
Note: When checking the electrical connection, it is essential to ensure that no ground short is created.
Release engine start (G000.000.03).
15345/20 E 00–05
Task Description
Section
G
Page
71
G510.000.01 Monitoring System, Equipment Function Check Check operation of level sensor on engine coolant expansion tank. The temperature sensor, pressure sensor and speed sensor are continuously monitored with the Integrated Test System (ITS) in the Engine Control System. If a monitoring unit fails, a warning is given. In event of a fault signal, replace respective component.
Remove speed sensor (crankshaft) Note: The speed sensor is an electronic component. Appropriate care is required for removal.
Separate electrical plug-in connection. Remove securing screw. Withdraw speed sensor (arrow). Remove O-rings.
Check speed sensor (crankshaft) Visually check speed sensor for damage, replace as necessary. Use an ohmmeter to measure resistance between Pin A and Pin B. Required resistance = 135 ohms ± 20 ohms In event of deviation from specified value, replace speed sensor.
15345/20 E 00–05
Section Page
Task Description
G 72
Special tools: Reference mandrel:
Install speed sensor (crankshaft) Note: The speed sensor is an electronic component. Appropriate care is required for removal.
Check that support bore in flywheel housing is clean and clean if necessary. Determine depth of support bore. For this purpose, carefully insert reference mandrel (1) into support bore until it contacts the graduated disc.
Measure projection “X” of reference mandrel over mating face of speed sensor and subtract from total length “L” of reference mandrel. Depth of support bore from mating face of speed sensor to graduated disc: T = L – X
15345/20 E 00–05
Task Description
Section
G
Page
73
Fit O-rings (1) on speed sensor (2) and coat with petroleum jelly.
Check gap clearance “S” between graduated disc and speed sensor: S = 1 mm to 2 mm For this purpose measure installation length “E” of speed sensor and compare with depth of support bore. Installation length “E” must be smaller by dimension “S” than installation depth “T”. If necessary, fit shims to achieve correct gap clearance.
Note: Before installing, check speed sensor for particular cleanness.
Insert speed sensor into support bore and press in up to mating face on flywheel housing (arrow). Tighten speed sensor with securing screw. Connect electronic plug-in connection on speed sensor.
15345/20 E 00–05
Section Page
Task Description
G 74
Remove pressure and temperature sensors Note: Sensors are electronic components. Appropriate care is required for removal. Store sensors so that they are protected from dirt and mechanical damage.
Use an open-end wrench to unscrew sensor. Attach suitable dust caps to screw-in thread of sensors. Store sensors so that they are protected from dirt and mechanical damage. Seal removal bores with suitable plugs.
Check pressure sensor (crankcase) Visually check pressure sensor for damage, replace as necessary. Carry out DC voltage test on pressure sensor. – Pin A = Earth – Pin B = Voltage output – Pin C = Voltage input Input voltage at 25 °= C 5.00 DC V Specified output voltage = 2.5 V DC 0.1 V DC In event of deviation from specified value, replace pressure sensor. Note: These values apply only when the engine is shut down or the pressure sensor is removed.
Check speed sensor Visually check pressure sensor for damage, replace as necessary. Carry out DC voltage test on pressure sensor. – Pin A = Earth – Pin B = Voltage output – Pin C = Voltage input Input voltage at 25 °= C 5.00 DC V Engine oil pressure sensor (1): Specified output voltage = 0.5 V DC 0.1 V DC Charge air pressure sensor (2): Specified output voltage = 1 V DC 0.1 V DC In event of deviation from specified value, replace pressure sensor. Note: These values apply only when the engine is shut down or the pressure sensor is removed.
15345/20 E 00–05
Task Description
Section
G
Page
75
Check pressure sensor (fuel high pressure) Visually check pressure sensor for damage, replace as necessary. Carry out DC voltage test on sensor. – Pin A = Earth – Pin B = Voltage input – Pin C = Voltage output Input voltage at 25 °= C
5.00 DC V
Specified output voltage = 0.5 V DC 0.1 V DC In event of deviation from specified value, replace sensor. Note: These values apply only when the engine is shut down or the pressure sensor is removed.
Check temperature sensor (engine coolant circuit, fuel, charge air coolant circuit, charge air, engine oil) Visually check pressure sensor for damage, replace as necessary. Measure resistance between Pin A and Pin B with an ohmmeter at different bath temperatures. Specified resistance at 0 °C = from 8500 ohms to 14000 ohms Specified resistance at 25 °C = from 2613 ohms to 2992 ohms Specified resistance at 100 °C = from 155 ohms to 190 ohms In event of deviation from specified values, replace sensor.
15345/20 E 00–05
Section Page
Task Description
G 76
Install pressure and temperature sensors Note: Sensors are electronic components. It is therefore necessary to take due care and ensure cleanness during installation.
Remove blanking plug. Check sealing surface and installation bore (thread) for particular cleanness, and clean if necessary. Screw in sensor with new sealing ring and tighten with torque wrench. Tightening torque: – H.P. fuel sensor – Charge air pressure sensor – Crankcase pressure sensor – Engine oil pressure sensor
70 Nm 30 Nm 20 Nm 20 Nm
– Temperature sensor – Lubricant:
16 Nm engine oil
Note: After starting engine, visually inspect sensor connections for leaks.
If leaks are found, slightly tighten sensor connections. If correct sealing cannot be achieved in this way, remove sensor and replace gasket. Switch on engine control system (G500.000.01). Release engine start (G000.000.03).
G510.070.01 Monitoring Equipment Lamp Test The monitoring system is not supplied by MTU. Carry out tasks as specified by Manufacturer.
15345/20 E 00–05
Section
Preservation
K
Contents
K000.000.01
Preservation Preface –
K000.000.03
Preservation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.
K000.000.05
Represervation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.
K000.000.07
Depreservation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.
K000.000.09
Description of services
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . .
Section
K
Preservation
15345/20 E 00–05
Preservation
Section Page
K 1
K000.000.01 Preservation – Pr eface Low operating and maintenance costs as well as operational reliability and availability depend on maintenance and servicing being carried out in compliance with our specifications and instructions. These instructions differentiate between preservation, represervation and depreservation. Preservation must be carried out on – New or overhauled engines after the test stand run – carried out at MTU. Not necessary if to be put into service immediately after completion. – Engines being withdrawn from operation for a period exceeding three months, as soon after the final operating period as possible. Preservation is adequate for storage for a period up to – 12 months under favourable storage conditions. – 6 months under unfavourable storage conditions, e.g. high humidity, salt-laden atmosphere, pronounced temperature fluctuations, etc. On conclusion of the preservation period, carry out represervation at the required intervals. Represervation is adequate for a storage period of up to – 6 months under favourable storage conditions. – 3 months under unfavourable storage conditions, e.g. high humidity, salt-laden atmosphere, pronounced temperature fluctuations, etc. Engines in special packing do not need to be represerved as long as the permissible relative humidity is not exceeded in the packaging enclosure room. – See inspection specification for Special Packing. Only preservation agents approved by the manufacturer may be used for preservation and represervation. – See Fluids and Lubricants Specification. These services may be omitted if – they cannot be completed due to operationally required special equipment (e.g. test stand). – the specified component is not fitted on the diesel engine. Before- and after-operation services on the engine must be carried out in accordance with the Operating Instructions (Section C). NOTE: The operations and tasks required for preservation, represervation and depreservation must be carried out in the recommended sequence. They are specified by 3-digit and 8-digit codes. Task descriptions: 3-digit codes in Section K 8-digit codes in Section G
15345/20 E 00–05
Section Page
K 2
Preservation
K000.000.03 Preservation Code No.
Task Description
G000.000.23
Shut d own engine
G000.000.01
Disable engine start
G180.000.07
Drain engine oil
K001
Cleanengine
G180.000.09
Fill corrosion inhibitor oil into engine
K002
Preserve fuel system
G000.000.03 G000.000.09
Release engine start Start engine
K003
Preserve engine coolant system
K004
Perform preservation run
G000.000.23
Shut down engine
G000.000.07
Bar engine with starting system and
K005
– spray corrosion inhibitor oil into air manifolds
G000.000.01
Disable engine start
K006
Spray corrosion inhibitor oil onto turbocharger compressor wheels
–
Connect fuel suction line to fuel system
G180.000.11
Draw off corrosion inhibitor oil f rom engine
K007
Seal engine exhaust system
K008
Seal engine air system
K009
Preserve engine externally
K000.000.05 Represervation Code No.
Task Description
K001
Cleanengine
G000.000.05
Bar engine manually, and
K005
– spray corrosion inhibitor oil into air manifolds
K006
Spray corrosion inhibitor oil onto turbocharger compressor wheels
K009
Preserve engine externally
K000.000.07 Depreservation Code No.
Task Description
K001
Cleanengine
G055.101.01
Remove cylinder head covers
G000.000.07
Turn engine on starter, and
K011
– check valvegear
G055.101.03
Install cylinder head covers
G180.000.11
Draw off corrosion inhibitor oil (residue) from engine
K012
Remove seals from engine air system
K013
Remove seals from engine exhaust system
–
For other services see Operating Instructions
15345/20 E 00–05
Preservation
Section Page
K 3
K000.000.09 Description of Ser vices K001
Cleanengine
Clean engine externally and check for corrosion. If necessary, remove rust spots and renew paint. NOTE: Do not use organic detergents to clean rubber or synthetic components. Wipe with a dry cloth only.
K002
Preserve fuel system
Connect the fuel delivery pump suction line to a separate tank, which should be filled with – Injection pump testing oil, to DIN ISO 4113 or – Diesel fuel with 10% corrosion inhibitor oil, for internal preservation. If possible, preserve the fuel system when the engine is hot. (Preservation is carried out during the preservation run, 004)
K003
Preserve engine coolant system
NOTE: Engine coolant systems are usually filled with prepared engine coolant and, therefore, protected from corrosion.
Fill engine coolant system with coolant containing 2% corrosion inhibitor oil or 50% antifreeze. The coolant preserves the engine during the preservation run. The coolant should be allowed to remain in the engine to provide protection against corrosion. Only drain the coolant at ambient temperatures – Below 0 °C for coolant / corrosion inhibitor oil emulsions – Below –40 °C for coolant / antifreeze emulsions
K004 Perform preservation run Run the engine approximately 20 minutes at idling speed. K005
Spray corrosion inhibitor oil into air manifolds
Remove plugs from air manifolds. Turn engine on starter. Spray corrosion inhibitor oil into air manifolds. Insert plugs into air manifolds. – Use only sealing rings which are in perfect condition.
K006
Spray corrosion inhibitor oil onto turbocharger compressor wheels
Disconnect air pipework from turbochargers. Spray compressor wheels and compressor housing with corrosion inhibitor oil while rotating the compressor wheels. Reconnect air pipework.
K007
Seal engine exhaust system
Cover the exhaust outlets at the turbocharger with blanking plates so that they are sealed against air and moisture penetration. NOTE: In order to ensure that these plates are not overlooked when the engine is returned to service, they must be shaped in such a way as to project beyond the flanges at a certain point. Paint the projections bright red and fold them back.
K008
Seal engine air system
Cover the air filter with plastic sheet.
15345/20 E 00–05
Section Page
K009
K 4
Preservation
Preserve engine externally
Spray or brush preservation agent on all exposed metalwork. NOTE: Do not apply grease to the sealing lips of radial-lip oil seals. Seal all openings in pipework, housings and turbochargers, with suitable, plugs or plates.
K010
Spray V-belt pulleys with corrosion inhibitor oil
Spray corrosion inhibitor oil onto belt running surfaces on generator, crankshaft PTO, fan wheel PTO and tension roller.
K011
Check and preserve valve gear
Check valve gear and fuel injection components for moisture, corrosion or other evidence of damage. Spray corrosion inhibitor oil into housing and onto valve gear and fuel injection system components.
K012
Remove seals from engine air system
Remove plastic sheet from air filters.
K013
Remove seals from engine exhaust system
Remove blanking plates from exhaust outlets. Note: When removing the plates, ensure that no foreign particles fall into the engine.
Reconnect bellows.
15345/20 E 00–05
Transportation Locking Device
Section
T
Contents
T036.051.01
Crankshafttransportationlockingdevice
T231.001.01
Enginemounttransportationlockingdevice
15345/20 E 00–05
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. .
Section
T
Transportation Locking Device
15345/20 E 00–05
Transportation Locking Device
Section
T
Page
1
T036.051.01 Crankshaft Transportation Locking Device Applicable to: 030.00160
General The transportation locking devices protect the crankshaft mounts against damage caused by impacts and vibrations during engine transportation. Transportation locking device – must be left in place until just before engine installation. – must, in the meantime, be removed only for engine barring (e.g. during preservation work) and immediately reinstalled. – must always be installed before the engine is transported.
Transportation locking device removal Remove transportation locking devices from driving end.
Store the transportation locking devices (including fixtures) together with this documentation for possible reinstallation at a later date.
Transportation locking device installation Transportation locking device at driving end Secure 2x plates (2) with screws (5) and washers (6) together with blanking plate (1) to the side openings of the flywheel housing. – Tightening torque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 . . . Nm . . + 25 Nm – Lubricant: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Engine . . . . . .oil Screw in nut (4) to thread end of the screw (3). Place 2x retainers (7) through the opening in the plate (2) and secure with screws (3). Tighten screws (3) alternately. – Tightening torque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 . . Nm . . . + 3 Nm – Lubricant: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Engine . . . . . .oil Fit nuts (4) on plate (2) and lock in position. Stick warning sign on blanking plate (1).
Attach this documentation to the engine where it can clearly be seen.
15345/20 E 00–05
Section
T
Page
2
Transportation Locking Device
15345/20 E 00–05
Transportation Locking Device
Section
T
Page
3
T231.001.01 Engine mount transportation locking device Applicable to: 230.00002
General These transportation locking devices block the engine mounts. The transportation locking devices protect the engine mounts against damage caused by impacts and vibrations during engine transportation. Transportation locking devices – Do not remove until the engine has been aligned and secured on the machinery foundation, but in all cases before the engine is put into operation. – The locking devices must always be installed before the engine is transported.
Operation of the engine with engine mount locking devices in place is impermissible. The transportation locking device must only be released when the mounts are fully loaded.
Transportation locking device removal Release nuts (7) and remove screws (9) from base plate (5). Check buffer clearance via control grooves (6) with feeler gauge. – Specified value: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 . . . mm ... If buffer clearance adjustment is necessary: Remove cover caps (1). Release securing nut (3). Screw central buffer (4) on hexagon (2) clockwise to the lower stop position. Back off central buffer (4) counterclockwise and adjust to distance “H” = 3.0 mm ± 0.3 mm. Tighten securing nut (3), holding central buffer (4) in position on hexagon (2). – Tightening torque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .580 . . . Nm . . ±50Nm – Lubricant: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Engine . . . . . .oil Fit cover caps (1). Store screws, nuts and washers together with these instructions for any possible future installation.
Transportation locking device installation Note: Before the transportation locking devices are fitted, the engine mounts must be subjected to the load of the engine weight for at least 48 hrs owing to settlement of the rubber elements.
Screw in and tighten screws (9) with nuts (7) and washers (8) into base plate (5). Attach these instructions to an engine carrier.
15345/20 E 00–05
Section
T
Page
4
Transportation Locking Device
15345/20 E 00–05
Keyword Index
A Abnormal turbocharger running noises, Troubleshooting, Section E, 4 After shutdown, C000.000.11, Section C,
4
Air filter replacement, G121.051.01, Section G,
41
Air filter, contamination indicator position check, G121.052.01, Section G, Application, D000.000.05, Section D,
42
1
Attachments security check, G000.000.27, Section G,
4
Attachments, hoses and hose connections check, G000.000.29, Section G,
4
B Barring engine manually, G000.000.05, Section G,
1
Barring engine with starting system, G000.000.07, Section G, 2 Battery charge state check, G309.001.05, Section G,
69
Battery check, G309.001.01, Section G, 69 Battery filling, G309.001.03, Section G,
69
Breather valve closing, G208.101.03, Section G, 63 Breather valve opening, G208.101.01, Section G,
63
C Centrifugal oil filter cleaning, G183.101.01, Section G, 50 Charge air coolant cooler, external element contamination check, G205.051.01, Section G, Charge air coolant draining, G203.000.05, Section G,
62
61
Charge air coolant level check, G203.000.03, Section G, 60 Charge air coolant pump relief bore check, Troubleshooting, Section E, 62 Charge air coolant sample extraction and analysis, G180.000.04, Section G, 61 Charge air coolant system filling, G203.000.01, Section G,
59
Charge air coolant system, vent line obstruction check, G202.651.01, Section G, Charge air manifold drain cleaning, G124.051.03, Section G,
62
43
Charge air manifold, drain water discharge and obstruction check, G124.051.01, Section G, Charge air pressure too low, Troubleshooting, Section E, 5 Charge air temperature too high, Troubleshooting, Section E, 4 Cleaning engine externally, G000.000.39, Section G,
7
Compressed air system condensate draining, G303.000.01, Section G, 68 Compressed air system, operating pressure check, G303.000.03, Section G, Compression pressure too low, Troubleshooting, Section E, Coolant capacity, A202.000.01, Section A,
3
6
Coolant discharge at intercooler relief bore, Troubleshooting, Section E, 5 Coolant loss, Troubleshooting, Section E,
9
Corrosion inhibitor oil draining, G180.000.11, Section G, Corrosion inhibitor oil filling, G180.000.09, Section G,
15345/20 E 00–05
48
48
68
42
Section
?
Page
1
Section
?
Page
2
Keyword Index
Coupling condition check, G252.051.01, Section G,
68
Crankcase ventilation, oil separator check, G018.101.03, Section G, 8 Crankshaft transportation locking device, T036.051.01, Section T, 1 Cylinder chamber endoscopic examination, G000.000.33, Section G, Cylinder head cover installation, G055.101.03, Section G,
5
25
Cylinder head cover removal, G055.101.01, Section G, 24
D Depreservation, K000.000.07, Section K,
2
Description of services, K000.000.09, Section K, Drain engine coolant, G202.000.07, Section G,
3
57
Drive system (driving end) security check, G250.000.01, Section G,
67
E Emergency shutdown, G000.000.25, Section G, 4 Engine and exhaust noise, A000.000.25, Section A,
5
Engine and external lines leak check, G000.000.21, Section G, Engine barring tool installation, G030.001.01, Section G, Engine barring tool removal, G030.001.03, Section G,
3
11
11
Engine control system initial operation, G500.000.07, Section G,
70
Engine control system switching off, G500.000.01, Section G, 70 Engine control system switching on, G500.000.01, Section G, 70 Engine coolant change, G202.000.09, Section G,
58
Engine coolant cooler, external element contamination check, G205.051.01, Section G, Engine coolant level check, G202.000.03, Section G,
62
55
Engine coolant level rising, Troubleshooting, Section E, 9 Engine coolant preheating, G202.400.01, Section G,
58
Engine coolant preheating unit initial operation, G202.401.01, Section G,
59
Engine coolant preheating unit, switching off, G202.401.03, Section G,
59
Engine coolant preheating unit, switching on, G202.401.03, Section G,
59
Engine coolant pressure too low, Troubleshooting, Section E,
9
Engine coolant pump leaking at relief bore, Troubleshooting, Section E, 9 Engine coolant pump relief bore check, Troubleshooting, Section E, 58 Engine coolant sample extraction and analysis, G180.000.04, Section G, Engine coolant system filling, G202.000.01, Section G,
56
54
Engine coolant system, vent line obstruction check, G202.651.01, Section G, 59 Engine coolant temperature too high, Troubleshooting, Section E, Engine coolant temperature too low, Troubleshooting, Section E,
8
8
Engine does not reach full-load speed, Troubleshooting, Section E, 2 Engine does not turn when starter is actuated, Troubleshooting, Section E, 1 Engine fires unevenly, Troubleshooting, Section E,
2
15345/20 E 00–05
Keyword Index
Engine layout, A000.000.01, Section A, 1 Engine model designation, A000.000.03, Section A,
2
Engine mount resilient element check, G231.051.03, Section G,
67
Engine mount security check, G231.051.01, Section G, 67 Engine mount transportation locking device, T000.000.02, Section T, 3 Engine oil change, G180.000.05, Section G,
46
Engine oil consumption abnormally high, Troubleshooting, Section E, 7 47
Engine oil draining, G180.000.07, Section G, Engine oil filter replacement, G183.052.03, Section G,
48
Engine oil level abnormally high, Troubleshooting, Section E, 7 Engine oil level check, G180.000.01, Section G,
45
Engine oil pressure too high, Troubleshooting, Section E,
8
Engine oil pressure too low, Troubleshooting, Section E, 8 Engine oil sample extraction and analysis, G180.000.04, Section G, Engine oil system filling, G180.000.03, Section G,
45
Engine oil temperature too high, Troubleshooting, Section E, 7 Engine power, A000.000.19, Section A, 4 Engine pressure checks, G000.000.15, Section G, 3 Engine running noise check, G000.000.19, Section G, Engine shutdown, G000.000.23, Section G,
3
4
Engine side and cylinder designations, A000.000.05, Section A, Engine speed check, G000.000.13, Section G, 3 Engine speed not steady, Troubleshooting, Section E, Engine start disabling, G000.000.01, Section G, Engine start release, G000.000.03, Section G, Engine starting, G000.000.09, Section G,
3
3
1
1
2
Engine temperature checks, G000.000.17, Section G, 3 Engine transportation, C000.000.17, Section C, 4 Engine turns but does not fire, Troubleshooting, Section E, 1 Engine warm-up procedure, G000.000.11, Section G, Engine weight, A000.000.13, Section A,
3
3
Engine wiring check, G500.000.09, Section G,
70
Exhaust gases black, Troubleshooting, Section E, 5 Exhaust gases blue, Troubleshooting, Section E, 5 Exhaust gases white, Troubleshooting, Section E, 6 Exhaust system check G140.000.01, Section G, 44 G140.000.07, Section G, 44 Exhaust system condensate draining, G365.000.01, Section G, 70 Exhaust system drain obstruction check G140.000.11, Section G, 44 G365.000.03, Section G, 70 Exhaust system security check, G140.000.03, Section G,
15345/20 E 00–05
44
46
Section
?
Page
3
Section
?
Page
4
Keyword Index
Exhaust system, exhaust backpressure check, G140.000.09, Section G, Exhaust system, exhaust gas colour check, G140.000.05, Section G,
44
44
Exhaust system, security and exhaust manifold insulation checks, G146.000.01, Section G, 44 Exhaust turbocharger connections check, G101.011.05, Section G,
39
Exhaust turbocharger, engine operation in event of turbocharger failure, G101.011.01, Section G,
39
F Fuel duplex filter replacement, G083.051.03, Section G, Fuel prefilter cleaning, G083.101.15, Section G, 38 Fuel prefilter priming, G083.101.01, Section G,
36
38
Fuel prefilter, element and gasket replacement, G083.101.09, Section G,
38
Fuel prefilter, water and contaminants draining, G083.101.03, Section G,
38
Fuel pressure too high, Troubleshooting, Section E,
4
Fuel pressure too low, Troubleshooting, Section E, 3, 4 Fuel supply check, G364.050.01, Section G, 69 Fuel supply system – filling intake line to engine, G364.200.05, Section G,
70
Fuel supply system, shut-off valve closing, G364.200.01, Section G, 69 Fuel supply system, shut-off valve opening, G364.200.03, Section G, 70 Fuel system filling, G080.000.03, Section G,
35
Fuel system, fuel delivery pump supply check, G080.000.05, Section G,
36
G General, Troubleshooting, Section E, 1 Generator condition check, G213.051.08, Section G, 67 Generator drive belt installation / replacement, G213.051.05, Section G,
66
Generator drive, drive belt condition and tension check, G213.051.01, Section G,
64
H H.P. pump leaking at relief bore, Troubleshooting, Section E, 4 High-pressure pump, relief bore obstruction check, G073.051.07, Section G,
25
I Initial operation, C000.000.05, Section C, 3 Injector installation, G075.051.09, Section G, 29 Injector removal, G075.051.01, Section G, 26 Injector replacement, G075.051.05, Section G,
29
Intake air system check, G120.000.07, Section G,
41
Intake air system, intake depression check, G120.000.05, Section G,
41
Intake air system, intake side leak and damage check, G120.000.03, Section G,
41
15345/20 E 00–05
Keyword Index
Section
?
Page
5
M Main engine dimensions, A000.000.09, Section A, 3 Main engine specifications, A000.000.17, Section A, 4 Maintenance echelon W6, D000.000.15, Section D,
4
Maintenance frequency chart, D000.000.07, Section D, 2 Maintenance schedule, D000.000.11, Section D,
2
Maintenance schedule – preface, D000.000.01, Section D, Maintenance system, D000.000.03, Section D,
1
1
Monitoring equipment lamp test, G510.070.01, Section G,
76
Monitoring system, equipment function check, G510.000.01, Section G, 71
O Oil capacity, A180.000.01, Section A,
6
Operating instructions – preface, C000.000.01, Section C, 1 Operational checks –maintenance echelon W1–, C000.000.07, Section C,
3
Operational data, A000.000.21, Section A, 5 Out-of-service period, C000.000.13, Section C, 4 Out-of-service periods, D000.000.17, Section D,
P
Power supply faulty, Troubleshooting, Section E,
4
6
Preheat temperature too low, Troubleshooting, Section E,
10
Preparations for initial operation, C000.000.03, Section C,
2
Preservation, K000.000.03, Section K,
2
Preservation – Preface, K000.000.01, Section K,
1
Protective device check, G307.001.01, Section G,
68
R Represervation, K000.000.05, Section K,
2
S Shutdown, C000.000.09, Section C, 4 Starter condition check, G172.051.09, Section G, 44
T Timing data (valve clearance adjusted), A050.000.01, Section A,
6
V Valve clearance adjustment (valve bridge with adjusting screw M12 (locknut 19 AF)), G055.050.03, Section G, 20
15345/20 E 00–05
Section
?
Page
6
Keyword Index
Valve clearance adjustment (valve bridge with adjusting screw M16 (locknut 24 AF)), G055.050.03, Section G, 15 Valve clearance check, G055.050.01, Section G, Valve clearances, A055.050.01, Section A,
13
6
Valve gear lubrication, G055.000.03, Section G,
12
Valve gear oil supply check, G055.000.01, Section G,
12
15345/20 E 00–05