Drilling Mcqs

1. The most appropriate formation for a casing seat is a. Fractured Limestone b. Fractured Dolomite d. Porous Sandstone e. Clean Shale 2. Shear 2. Shear mechanism of cutting formations requires that the formation exhibit a a. High Compressive strength b. strength  b. Low compressive strength 3. In formations where heavy to complete losses of circulation are expected the jet sizes should be a. Very small b. b. Very large or open 4. What is the benefit of a center jet in a bit? The “Center “jet or nozzle helps clean the “dead” spot in the center area of the formation and also

aids in cone cleaning to a certain degree. It can increases ROP up to 10 % due to optimum cleaning of the hole. 5. Resistance to flow in mud due to chemical reactions is called a. Plastic Viscosity b. Yield Point c) Point c) Gel Strength 6. Annular velocity is generally considered across a.BHA c.Drill Collars c.Drill Pipe 7. In Cement Bond Log if the MV records very high readings (40 to 50 Ohms) the quality of the cement bond would be rated a. Excellent b. Good c. Fair d. Poor e. Free Pipe 8. Name 5 mud properties which are taken at regular intervals at the drilling site. Give their units a. Mud Density (Sp.Gr, PPG) b.Funnel Viscosity (sec) c. Filtrate or water loss (cc) d. Solids Content (%). e.Chlorides (ppm) 9. A mast remains a single after manufacture manufacture and is relatively relatively portable. True/False True/False 10. A three joint of drill pipe is a) Double b) Single c) Triple or stand 11. Name 4 casing accessories a.Shoe b. Float collar c. Stage Collar d. Centralizer 12. In designing a casing program the liner is run from the surface to the section’s total depth .

True/False True/False 13. With a top drive the rotary table does not rotate . True/False True/False

1

14. Which of the following is not part of the auxiliary equipment on a rotary rig? a. Electric Generators b. Mud Pumps c. Air Compressors d. Degasser e. Desilter and Desander 15. What does the abbreviation SIDPP and SICP stands? In calculating kill mud weight which is considered: SIDPP or SICP. SIDPP stands for Shut in Drill Pipe Pressure and SICP stands for Shut in casing Pressure. SIDPP is considered for calculating kill mud weight 16. A test performed to determine optimized drilling parameters is called. a. Drill off Test b. Bottoms up Test c. BOP Test d. Leak off or Formation Integrity Test 17. If a formation contains abundant chert and pyrite PDC is an ideal bit to drill such a formation. True/False 18. Metallic displacement Sheet is maintained during tripping to determine if there is any inflow or loss of circulation. True/False 19. During mixing cement the excessive foam produced is eliminated by adding. a. Fluid Loss Additive b. Retarder c. Dispersant d.Antifoam 20. Acidization/Stimulation is performed to increase the production of a well. True/False 21. Name three sandstones formations producing hydrocarbon in Pakistan. 1. Lower Goru Sandstone 2. Pab Sandstone 3. Ranikot Sandstone 22. What are the three Well Planning Objectives? a. Minimum Cost b. Safety c. Usable Hole 23. The overburden stress gradient is supposed to be: a. 0.433 psi/ft b. 0.465 psi/ft c. 0.770 psi/ft. d.1.00psi/ft 24. Heat from the formations and friction of drilling makes flow line mud temperature. a. Much higher b. same c. Much lower than the surface temperature 25. The pressure at any point inside the borehole comes from the weight of the mud a. Above it b. Below it 26. Almost no mud cake is built over the a. Solid Rock  b. Permeable Rock, since no filtrate enters such a formation.

2

27. Just as water buoys up heavy objects, the mud buoys up the drill string so the downward pull on the drill string is a. Increased b. Decreased 28. As solids increases the viscosity of the drilling fluid it a. Becomes easier b . Harder to pump through the the borehole 29. At high pump rates all types of fluids becomes a. Laminar Flow b. Turbulent Flow c. Transitional Flow 30. Fluids that flow easily, yet form gels when they stop flowing are called a. Dispersed Fluids b. Flocculated Fluids c. Thixotropic Fluids. 31.  The Thixotropic properties of drilling fluids are very useful in keeping cuttings a. Suspended  b. Not suspended when drilling stops. 32.In case of complete loss of circulation it is a good practice to pump cement through bit. a. Yes b. No 33.In formations where large concentration of LCM is to be pumped the jet sizes should be: a. Large b. Small 34. Barite has SP.GR of: a.4.2 b.3.6 c. 2.4 35. Formation damage is minimal when fluid loss is: a. High b. Low 36. Fixed cutter bits runs longer in hole as these have no moveable parts. A. True b. False 37. A column of fresh water in 8 ½ inch hole at 1000 feet will exert a hydrostatic pressure of: a. 433psi b. 250 psi c. 465 psi 38. A bit which is coded 1-1-3 is a: a.TCI bit b. Tooth /Milled bit 39. PDC bit is a roller cone bit: a. True b. False 40.If the annular velocity is below recommended range cuttings will: a. Will remain suspended in hole b. Will rise to surface and fall on the shaker screens 41. Which is a more economical bit: a. Bit cost: $25,000: Cost/feet: $50 b.Bit cost: $125,000: Cost/feet: $40 42. Name 5 indicators which while drilling approaches, but have not yet penetrated a high pressure zone are observed. a. Increase in transit time in Sonic log b.Decrease resistivity in resistivity log c. Decrease in shale density factor d. The chlorides content in drilling fluid will increase e. A drilling break (ROP will increase 2 to 3 times in transition zone) 43. What is a tangible cost in AFE /Budget? Any item which has a salvage value

3

44. Name 3 tangible costs in AFE/Budget a. Tubular Equipment b. Well head Equipment c. Completion Equipment 45. Name 3 Intangible costs a. Drilling Fluids b. Cementing c. Rental Equipment 46. On consignment basis the service company a. Charge the operator for all the items/materials supplied to the operator b. Charge the operator for only for those items /materials which had been consumed by the operator 47. Mud detergents are more effective in a. Surface holes b. Deep, high temperature holes 48) In a fishing situation concerning “Green Cement” a) Always know the theoretical top of cement * b) Theoretical top of cement have no significance 49) In a washout section of the hole a) Annular velocity is low * b) Annular velocity is high 50) Horizontal distance between two sections is known as: a) Horizon b) Horizontal c) Depth

d)

*

Departure 8) Drop point

51) Name 5 sensors which are installed in a Mud Logging Unit.   a) Hook load Sensor b) Torques Sensors c) Rotary Speed Sensor d) Pit Volume Sensors e) Flow out Sensor. 52) Abbreviation of AFE is a) Authority for Expenditure b) Approval for Expenditure c)* Authorization for Expenditure 53) In a primary casing cementation job dispersants are added to a) Increase the viscosity of the cement slurry b)

*

Decrease the viscosity of the cement

54). If an item has a salvage value it is a)

*

Tangible b) Intangible

55). Name the 3 types of pressures commonly mentioned in Drilling Terminology. a) Normal Pressure b) Subnormal Pressure c) Abnormal Pressure

4

56). What are the main factors which can result in abnormal pressures/well kicks? a) Artesian Systems b) Uplift c) Fault Communication 57). What is the abbreviation of ICP and FCP? Which plays a pivotal role in killing of a well? ICP: Initial Circulation Pressure

FCP: Final Circulation Pressure. FCP plays a pivotal role in

killing the well. 58). In Casing Design name the 3 Safety Factors.  a) Burst b) Collapse c) Tension 12. If a pipe is stuck and the drill string cannot be rotated, raised, or lowered but circulation is normal, is it a)* Differential Sticking b) Mechanical Sticking 59). Name 5 conditions which can result in drillstring getting stuck. a) Differential Sticking b) Under-gauge Hole c) Key Seats d) Tapered Hole e) Objects alongside Drill String 60). Name the three Technological Approaches for Formation Evaluation. a) Electrical Logging and Sampling b) Coring c) Mud Logging 61). Name 5 casing accessories. a) Float Collar b) Stage Collar c) Casing Shoe d) Centralizers e) Scratchers 62) Length along the drill hole is known as vertical depth a) True b) False 63) The depth from where the traverse extending from the KOP to the slant section is called slant a) True b) False  64) Rotary bits drill the formation using primarily two principles. Name these principles. a ) Sh e a ri n g ( f o r s o f t f o r m a t i o n s ) b ) C o m p r e s s i o n ( f o r h a r d f o r m a t i o n s )

65) An operation which will positively confirm the presence of viable hydrocarbon is. a) Evidence from flush samples b) Readings from gas chromatograph c) Core samples d) DST (Drill Stem Test)

66). What is the abbreviation of CBL and what are the benefits in recording this log? Cement Bon d Log . The units are in Ohms. (0-50 or 100). The higher the ohm s num ber the poorer the b o n d i n g b e t w e en c e m e n t a n d f o r m a t i o n a n d c e m e n t a n d c a s i n g . CB L i n d i c a t es t h e q u a l i t y o f c e m e n t bonding and this is the primary benefit.

67) Name the three well planning objectives. a) Cost b) Safety c) Usable Hole

5

68) If the inner/outer cutters of a bit are graded 7/8, bearings ineffective, gage:1/8 inch out of gage, dull char-broken teeth/inserts, 2 locked cones , can this bit be run again for drilling or even cleaning out cement  A) Yes b) No 69) Seal mechanism to trap abnormal pressure is a) Dolomite b) Limestone c) Porous Limestone d) Clean Shale 70) Free Point Indicator Tool measures the a) The deepest top of the stuck section b ) T h e s h al l o w e s t t o p o f t h e s t u c k s e c t i o n   71) Name three tangible costs in AFE or Budget. a) Tubular Equipment b) Well Head Equipment c) Completion Equipment 72) Mud detergents are more effective in a) Surface holes b) Deep, high temp erature holes 73) The procedure for field determination of fracture gradient is called a) Lag Off Test b) Formation Integrity Test  c) Kick Off Test d) Drill Off Test 74) Are nozzles in a bit interchangeable? a) Yes  b) No 75) Is it a good drilling practice to place a cement plug through the bit? a) Yes b) No 76). Name 5 mud properties routinely recorded at drilling site and also give their units.

a. Mud Density (Sp.Gr, PPG) b.Funnel Viscosity (sec) c. Filtrate or water loss (cc) d. Solids Content (%). e.Chlorides (ppm) 77) If the influx gradient, when the well takes a kick, is 0.2 to 0.3 it is a) Probable Gas b) Probable combination of Gas and Oil c)Fresh Water d) Probable Water or Salt Water 78) A box is a) Female section of a connection b) Male section of a connection 79) A brake is a devise in a drilling rig for a) Accelerating the motion of a mechanism b) Arresting the motion of a mechanism 80) Breakout is to a) Screw one section of the pipe from another section   b) Unscrew one section of pipe from another section

6

81) Which class of cement in majority of primary cementation job? a) APT CLAS”A” b)API CLASS”B” c)API CLASS”C” d)API CLASS”D” e) API CLASS”E” f) API CLASS”G”

82. The acceptable working environmental limit of H2S gas is a)10ppm b)100ppm c)200 ppm e) 300 ppm 83). Drilling in a transition zone, prior to entering abnormal pressured zone the Delta T (Difference between temperature in and temperature out) a) Sharply Decreases b) Sharply Increases 84). Name 5 well types. a) Wildcat b) Exploratory c) Appraisal d) Development e) Work over 85). Bit jet sizes ranges from 3/32 inch to 32/32 inch. a) True b) False 86) Are bit nozzles interchangeable? A) Yes b) No 87) What is the abbreviation of “UBD”? Under Balance Drilling 88. Barite is used to a) Increase Mud Density b) Increase Mud Viscosity 89). Name 4 major systems applied in rotary drilling. a) Power System b) Rotating System c) Circulating System d) Well Control System 90) Name 2 components of the Power System. a) Prime Mover b) Drive (Mechanical or electric) 91) Name 2 components of the Hoisting System. a) Derrick or Mast b) Draw-works 92) Name 2 components of the rotary system. a) Bit b) Rotary Table 93. Name 2 components of the Circulating System. a) Mud Tanks b) Mud Pumps 94. Name 2 components of the Well Control system. a) Drilling Mud Blow-out Preventers 95. Name 2 components of the Auxiliary System. a) Electric Generators b) Desander and Desilter 96. Name 2 members of the rig crew. a) Company Man b) Driller 97. Abbreviation of BOP. Blow Out Preventer 98. Abbreviation of ROP. Rate of Penetration 99. Abbreviation of WOB. Weight on Bit

100.Abbrevaition of RPM. Rotation per Minute

7