Hazard Identification Risk Assessment and Risk ControlFull description
Hazard Identification Risk Assessment and Risk Control
Full description
Risk assessments for electrical tasks
HAZARD IDENTIFICATION RISK ASSESSMENT AND RISK CONTROL (HIRARC/HIRADC) Office HAZARD for building Sample FREE
HAZARD IDENTIFICATION RISK ASSESSMENT AND RISK CONTROL (HIRARC/HIRADC) Office HAZARD for building Sample FREEDeskripsi lengkap
Hazard identification and risk assessment were carried out in different department of the brakes India manufacturing plant. Risk has been calculated by the risk table range between 1 to 25 were consequence and frequency of occurrence rating between 1
Hazard Identification Risk Assessment and Control Measures for MHF
Full description
Full description
RISK ASSESSMENTFull description
Risk Based Thinking as per ISO 9001:2015
Job Hazard Analysis
TALK ABOUT VARIOUS POTENTIAL JOB HAZARD AND CONTROL
Deskripsi lengkap
Job Hazard and Risk Assessment
Job Hazard and Risk Assessment ITEM NO.
HAZARD
HAZARD EFFECT
EFFEC PROB RISK T
1
Caliper tool string becomes stuck while running Caliper inside well bore
Unable to pull tool string. Follow procedures to pull out of weak point
Low
Low
2
Wireline cable is damage or broken while in hole. Master or crown valve closed while in hole
Wireline cable parts causing possible personnel injury. Caliper and wireline lost downhole
High
Low
Wireline sheave fails
Possible injury to personnel. Loss of tools and /or damage to wireline cable
High
Low
3
MINIMIZE RISK BY
Detailed engineering drawings are made available of all possible Low 'risk' areas. Minimize flat shoulders on tools and centralizers All crane operations will be suspended over or near wireline unit while in operation. Sheave wheel guards will be Low securely fastened. Constant monitoring of wireline cable during operation. Proper wireline cable maintenance Visual check of sheaves is implemented prior too Low and during operation. Correct mounting and usage of sheave is carried out
RESIDUAL RISK
Low
Low
Low
Job Hazard and Risk Assessment ITEM NO.
HAZARD
HAZARD EFFECT
EFFEC PROB RISK T
4
Damage caliper tool Injury to personnel string while rigging and equipment up or rigging down
Low
Low
5
Hydraulic failure (Power pack )
Unable to retrieve tools from well bore
Low
Low
6
Failure of tools while in hole
Delayed or unable to carry out operation
Low
Low
MINIMIZE RISK BY
Good communication established with all key Low personnel prior too and during wireline operation. Power pack maintenance perform before all operations. Low Visual inspection perform during operations All tools and equipment to perform caliper Low operation to be check prior to load out to well site.
RESIDUAL RISK
Low
Low
Low
Job Hazard and Risk Assessment ITEM NO.
HAZARD
HAZARD EFFECT
Loss of caliper tool string in hole create fishing operation. Broken cable causes injury
7
Pull out of weak point
8
Caliper damage, Caliper tool string failure or loss due to lost or operation debris left in hole delay due to after milling hazard's downhole operations
9
Electronic depth measurement system
Caliper tool string lost or damage due to in-accurate depth correlation.
EFFEC PROB RISK T
Med
Low
Med
Low
Low
Low
MINIMIZE RISK BY
Ensure weight indicator is functioning effectively. All potential hang up areas are Low minimized and well documented. Cable head built to proper pull out or weak point Survey to be carried out with potential Low hazards in mind. Logging speed >TBD ft/min. Check depth system prior to running in hole. Ensure mechanical Low back-up working properly. Correlate with known tubulars, casing collars or BHA
RESIDUAL RISK
Low
Low
Low
Job Hazard and Risk Assessment ITEM NO.
10
11
HAZARD
HAZARD EFFECT
EFFEC PROB RISK T
Manual handling and lifting
Possible personnel injuries incurred and/or damage to equipment.
Med
Low
Damage rubber packer
Steam comes out from Lubricator and possible with H2S gas
Low
Low
MINIMIZE RISK BY
Correct lifting techniques to be used, Low crane to be used for heavy and awkward lifts. Check rubber packer before usage. Service BOP for every run. If rubber packer swell during operation and Low more steam comes out, use pack-off pump to squeeze the rubber and diminish rubber packer wireline hole.
