KOC Piping Specification

OWNER

EPC CONTRACTOR

NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KUWAIT OIL COMPANY (K.S.C.) A Subsidiary of Kuwait Petroleum Corporation

COMMENT RESOLUTION SHEET DOCUMENT NO. 50489-530-051-SPC-1002

CONTRACT NO.: 14050489 PROJECT NO.: EF1902

VALVE MATERIAL SPECIFICATION

Company DTN Reference:TRANS-EF1902-AMEC-RTS-000267 Sr. No.

Rev

Company Comment

B

DATE :

Page 1 of 6 17-Jan-15

Company DTN Date: 11-Dec-14

L&T Response To have interchangeability of usage under different service conditions, we shall be procuring valves with only Primer Coating (Inorganic Zinc Silicate) applied. Finish paint of these valves shall be carried out after installation.

1

Contractor shall indicate the applicable standards and project specifications for painting and the painting system on all data sheets

2

SOUR SERVICE REQUIREMENTS- Reference to, and use of guideline for material selection for NACE MR 0175 / ISO 15156 in Appendix ll of KOC-MP-010 shall be made.

Noted and complied.

3

Weld overlay of CRA shall be compliant with section 8.6 of KOC-MP-010.The minimum weld overlay thickness after machining is 3mm.The required CRA deposit shall be achieved through a minimum of three (3) passes. Data sheets to state these requirements, where applicable.

Noted and complied.

4

Flange insulation kit shall be provided for joints where there are dissimilar metals, to avoid galvanic corrosion. Contractor to make note of this requirement in data sheet

There are no such cases of Dissimilar Metal joints in valves as per Valve Material Specifications. Hence there is no requirement for flange insulation kit in valves.

5

Valves for Piping Class N10B / N30B have not been included in this specification. Please provide data sheets for these. There are valves in these piping classes featured on P&IDsBasis for Rejection

Noted and complied

Inorganic zinc silicate has compatibility with paint systems applicable for different service conditions in the project. Hence the same is in compliance with KOC-P-001 ( KOC Standard for painting and coating on metal surface )

Company Confirmation

OWNER

EPC CONTRACTOR




Sr. No.

Rev


Company Comment

L&T Response As per Comapany standards for Gate/ Globe valves for Handwheel MOC has been defined. Valve MOC

6

Handwheel material shall be as per specific valve standard and KOC-MP-010 and KOC valve standards. Ensure data sheets are in compliance where applicable

CS Valves (0.5”-1.5”) CS Valves (2” & above) SS Valves (0.5”-1.5”) SS Valves (2” & above) Cu-Alloy (Potable Water) Cu-Alloy ( Brackish / Fire Water )

Handwheel MOC Malleable Iron/ Steel Malleable Iron / Ductile Iron / Steel

Malleable Iron / Aluminum / Steel / Cu-Alloy

We have generalised the MOC for valve handwheel in Valve Material Specifications as Malleable Iron / Ductile Iron / Cast Steel. The same is in compliance with KOC standards for valves

7

8

For bolts on valves which are direct buried, insulated or otherwise denied atmospheric exposure, bolting material ASTM A 193 Gr. B8 / ASTM A194 Gr.8 shall be used in Pipe Classes where the same has been specified for flanged connections

Company standards KOC-MP013/014/015/016 and related addenda shall be referenced in manufacturing and testing for each valve material specification sheet

For valves with MOC as SS / SDSS bolting material has been defined as ASTM A193 Gr B8M / ASTM A 194 Gr 8M. However pl. note that none of the valve in the project is direct buried. All underground valves are located in the valve pit. Para 8.0, (Technical Requirements) has been defined in the main body of the specification which incorporate these comments. Refer SECTION 4.1.2 of Doc. Valve Material Specification. This defines all relevant “KOC Standards and Engineering Group Specifications“. Also in each valve specification sheet, Note no. 1 is specifically defined as “This Valve Specification Sheet shall be read in conjunction with technical notes to Valve Material Specification”

B

DATE :



OWNER

EPC CONTRACTOR




Sr. No.


Company Comment Inspection and testing of valves shall be fully compliant with KOC valve standards

9

10

11

Rev

KOC-MP-013/014/'015/016/033 ensure testing requirements are fully compliant in Valve material specification For valves with a back seat, include back seat testing specification shall be included in the relevant data sheet

For sour service carbon steel piping classes (CxxB),the valve trim material is to be selected from those listed as available in KOC-MP-010.Data sheet states SDSS which is not permitted for this line class. Contractor to revise to a suitable material, considering Appendix II of KOCMP-010

L&T Response

Refer L&T Response to company comments at Sr. No.8

Back Seat Testing requirements shall be governed by the relevant Testing Standards (eg. API 598, MSS-SP-80 etc.) as defined in Valve Material Specification. Selection of MOC has been done based on Appendix-II of KOC-MP-010, considering composition of service fluid. Appendix II of KOC-MP-010 permits use of Duplex / Super Duplex SS based on respective stream conditions in other lines. 25Cr. Valves (MOC: SDSS) are defined in P&ID’s for several lines having piping classes CxxB. Refer SECTION 19.0 of Piping Material Specification (Doc.No.:50489-530-051SPC-1001) This section defines “ TRIM Material Selection of Valves for Sour Service”.

Refer L&T Response to company comments at

12

Material specification for C35B shall be Carbon steel body, Contractor to remove C35B from valve #51479 which is a SDSS valve and other similar instances.

Valves with Body/ Bonnet/ Cover MOC as Stainless Steel :

13

LIST OF CHANGES Contractor to submit a technical query for the use of different bolting material for valves for review. Recommendations in items #2 and #3 are acceptable for implementation

Sr. No.11. SDSS valves shall be used wherever specified in P&ID in the same piping class.

Bolting Materials shall be revised to Stainless Steel (A193 Gr. B8M / A194 Gr. 8M) in line with company standards for valves

B

DATE :



OWNER

EPC CONTRACTOR




Sr. No.

Rev


Company Comment

L&T Response

14

Add note to list of changes to indicate the use of stellited seats for 800# valves in piping class C13A.This is a change from the FEED document and therefore requires indication in the list of changes

Noted and complied

15

Section 4.1.3- Add reference to Pipeline data sheet. There are check valves on the pipelines, local to the disposal wells

Noted and complied. Valve Data Sheets for pipeline valves shall be submitted through separate Doc. Noted and complied.

16

Section 6.0 part 2) - Statement should read "pressure ratings........are expressed as per ASME B 16.5......"

17

Section 7.10 Revise requirement for gear operators for plug valve to be in compliance with KOC-MP016.Requirement to provide for sizes 6" and larger for Classes 150# and 300# and 4" and larger for Classes 600# and 900#

Nominal pressure ratings for Flanges, Valves are defined as per ASME B16.5, Class rating for socket weld and threaded end connections shall be series 3000# etc. as per ASME B16.11. As per KOC-MP-016, Plug Valves shall have Gear Operator as per following Criteria : Class

Sizes

150#, 300# 600#

> 6” NB > 4” NB

Same has been defined in submitted Doc. “ Valve Material Specification”

18

Clause 7.11- Remove this clause as there are valves other than globe which are used for throttling function. It is feasible to state that globe valves are to be used for throttling only

Noted and complied.

19

Clause 7.13 - change the word "shall" to "should be" as this is not a contractual requirement

Noted and complied.

20

Section 7.16 State a requirement for a minimum 150mm long seamless pipe nipple

We have specified clear requirement on pipe nipple length as 150mm. Specifying length as “Minimum 150 mm, may cause discrepancy in terms of pipe nipple length in items being supplied by different vendors”.

B

DATE :



OWNER

EPC CONTRACTOR




Sr. No.

Rev


Company Comment

DATE :

L&T Response

21

Noted and complied.

22

Remove piping class C15B and C35B from data sheets for valves with SDSS construction, this material is not specified for the particular piping class

Refer L&T response comments at Sr. No.11

to

company

23

Revise index and data sheets for Valves in line class C35B to have trim materials selected from the prescribed options in KOC-MP-010. Refer to comment 11 for further details.

Refer L&T response comments at Sr. No.11

to

company

Refer pipe class Q35A, KOC-MP-010 : Service limit states Cu-Ni material has test P/T rating of 20 bars @ 38 °C .

24

As per Note 5: “If Pressure / Temperature ratings per EEMUA or MSS SP-80 are exceeded, full Duplex Stainless Steel material shall be used for piping, components and valves”. SDSS MOC for piping components of size range 2” & below has been selected based on this. The Design Pressure in wash water circuit are expected to be more than 20 bars.

25

For Valve data sheets with both piping classes C13B & F10A,add note to indicate Monel trim is for class F10A only

Noted and complied

26

Valve data sheet 54301 - move note 15 to Material of Construction section, rather than under Type of Construction heading.

Noted and complied



Section 7.19 - Add abbreviation for BOQ in abbreviations table. Remove details of limit switch specification, this shall be covered in instrumentation documents. Make reference to applicable instruments specification instead of providing details.

Piping class Q35A to have Bronze/Ni-AI Bronze valves as per KOC-MP-010

B

OWNER

EPC CONTRACTOR




Sr. No.

Rev


Company Comment

27

For Piping class C15B, there is no approval to use Dual plate type check valve. Revise data sheets to show permitted check valves only as per KOC-MP-010

28

All valves shall be hydro tested and pneumatic tested as per KOC standards for valves. Contractor shall revise data sheets to comply with this requirement

DATE :

L&T Response

Sr. No.8



Noted and complied

Refer L&T Response comments at

B

to

company

NEW GATHERING CENTRE GC-30, IN NORTH KUWAIT

DOCUMENT NO

KOC CONTRACT NO.: 14050489

50489-530-051-SPC-1002

LIST OF CHANGES WITH RESPECT TO FEED DOCUMENTS FOR PIPING VALVES Item No.

1

2

3

KOC Document No.

KOC Standard for Valves: Part 1 - Ball Valves, KOC-MP033 Part 1, KOC-MP-010

KOC Standard for Valves: Part 1 - Ball Valves, KOC-MP033 Part 1

KOC Standard for Valves

REV B

Reference / Pipe Class

ITB Requirements

L&T Recommendation

-----

KOC Standard for Ball Valves : Ball valve intended for potable water service shall be in accordance with standard AWWA C507 KOC-MP-010 : Ball Valves have been defined as per Design STD API 6D / BS EN ISO 17292.

All Ball Valves have been defined as per Design Std. API 6D / BS EN ISO 17292 in line with Doc No. KOC-MP-010.

-----

Part. 1.0, Note-2 As per this note, class 800 valves, Socket Weld / Threaded Type are of reduced bore. Doc. No. EF1902-015-LH-1002-ADD.DE2 (Add. To Piping Design) Pt. 9. clause 5.0 : " Whenever Ball Valve are provided, they shall be Full Bore Type."

All Ball Valves have been defined as full bore in line with Doc. No. EF1902-015-LH-1002ADD.DE2.

C13A

Trim Material has been defined as 13% Cr in Gate, Globe & Check Valves for both Small (800#) and Large (150#) Bore Valves in KOC-MP-010.

As per KOC Standards for valves, following valves shall have stellited surfaces. Small Bore : 800# Large Bore : 600# & above Trim Material has been defined as Stellited for Small Bore (800#) Gate, Globe & Check Valves in line with KOC Specifications for Gate / Globe Valves.

KOC Response

Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No


14050489

Page No : 2 of 237 Contractor Document Number

Rev

50489-530-051-SPC-1002

B

REVISION HISTORY SHEET This page is a record of all revisions of this document. All previous issues are hereby superseded and are to be destroyed. Page No.

Clause No.

Description of Revision

5

3.2

11

4.1.2

KOC Standards and their addenda / criteria relevant to Limit Switches added.

13

6.0 (2)

Clause modified as per company comment

14

7.11


14

7.13


14

7.19


16

8.0

Para for “Technical Requirements” added

16

9.0

Statement related to material selection guideline for sour service added.

17

9.3

Para for welding requirement added

18

12.0 (d)

Table modified to include abbreviation L : Limit Switch arrangement

20

Table – 1

Valve Data Sheet Index upgraded.

---

General

Valves with MOC as SS / SDSS : Bolting material has been revised to ASTM A193 Gr B8M / ASTM A 194 Gr 8M

---

General

Pipe classes N10B / N30B added in the following Valve Data Sheet: 51399, 51499, 52399, 52499, , 53399P, 53399D, 53499P, 53499D, 54399, 54499

---

53311D, 53312D

---

55511L

Valve Data sheet added

---

53679

Check valve data sheet related to pipe class PA9A deleted.

---

51378F, 52378F, 53378DF, 54378F

Abbreviation BOQ : Bill of Quantity added.

Valve Data Sheets deleted (Swing type Check valve has been defined for 26” & above in pipe class C15B).

Note related to valve trim material added.

Revision



14050489


Rev

50489-530-051-SPC-1002

B

INDEX 1.0

SCOPE ..................................................................................................................... 4

2.0

APPLICATION ......................................................................................................... 4

3.0

TERMINOLOGY ....................................................................................................... 4 3.1 3.2

4.0

DEFINITIONS ................................................................................................ 4 ABBREVIATIONS .......................................................................................... 4

REFERENCE STANDARDS, CODES AND SPECIFICATIONS ............................ 7 4.1

LIST OF STANDARD AND CODES ............................................................... 7

5.0

ENVIRONMENTAL CONDITIONS ........................................................................ 13

6.0

UNITS OF MEASUREMENT ................................................................................. 13

7.0

GENERAL REQUIREMENT .................................................................................. 13

8.0

TECHNICAL REQUIREMENTS............................................................................. 16

9.0

SOUR SERVICE REQUIREMENTS ...................................................................... 16 9.1 9.2 9.3

REQUIREMENTS FOR CARBON STEEL ................................................... 16 TECHNICAL REQUIREMENTS FOR STAINLESS STEELS AND OTHER CRA’S .......................................................................................................... 17 WELDING .................................................................................................... 17

10.0

INSPECTION AND TESTING REQUIREMENTS .................................................. 17

11.0

NON DESTRUCTIVE EXAMINATION (NDE) REQUIREMENTS ......................... 18

12.0

VALVE DATA SHEET NOMENCLATURE............................................................ 18

APPENDICES: APPENDIX-I TABLE – 1

VALVE DATA SHEET INDEX

20

VALVE DATA SHEET : DETAIL DESCRIPTION

26

APPENDIX-II

APPENDIX-III TABLE – 2

BALL VALVE NIPPLE DETAIL

237

Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT

Page No : 4 of 237

KOC Contract No

14050489

1.0

Contractor Document Number

Rev

50489-530-051-SPC-1002

B


SCOPE a) This Specification and Valve Data Sheets describes the basic design and material requirements for different type of valves, to be used for various fluids / services such as Gas / Liquid Hydrocarbons (Sweet / Sour) and NonHydrocarbon fluids / services etc. related to process and Utility piping systems of NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT. b) This specification covers the design, manufacture, inspection, testing and supply requirements of valves for installation at the facility in Kuwait and developed based on KOC specifications.

2.0

APPLICATION All material(s) listed in this specification when supplied / installed shall be brand new and of prime quality and shall conform to the requirements of this specification, Standards / Codes / Specifications referenced herein and shall also be fit for the purpose Any exceptions or deviations from this specification along with their merits and justifications shall be brought to the attention of Purchaser for their review & approval.

3.0

TERMINOLOGY

3.1

DEFINITIONS For the purpose of this Specification the following definitions shall apply.

3.2

Company

Kuwait Oil Company (KOC)

Client

Kuwait Oil Company (KOC) and / or Its appointed representative

EPC Contractor

Larsen & Toubro Limited

ABBREVIATIONS AARH

Arithmetic Average Roughness Height

AI

Instrument Air

AL

Aluminum

AL BRZ / BRNZ

Aluminum Bronze

ANSI

American National Standards Institute

AP

Plant Air

API

American Petroleum Institute

AS

Alloy Steel



Rev

50489-530-051-SPC-1002

B


14050489

ASME

American Society of Mechanical Engineers

ASS

Austenitic Stainless Steel

ASTM

American Society for Testing and Materials

BAR (g)

Bar, Gauge, (Pressure Unit)

BD

Blow down & Relief

BE

Bevel End

BHN

Brinell Hardness Number

BOQ

Bill of Quantity

BRW

Branch Weld

BRZ / BRNZ

Bronze

BS

Booster Station

BS

British Standard

BW, BWE

But Weld, But Weld End

CLR

Crack Length Ratio

CRA

Corrosion Resistant Alloy

CS

Carbon Steel

CSR

Crack Surface Ratio

CTR

Crack Thickness Ratio

DC

Chemical Drain

DD

Dedicated Drain

DH

Oily/Hydrocarbon Drain

DO

Open Drain

DP

Pressurized Drain

DPT/I/E

Dye Penetrant Testing/Inspection/Examination

DSS

Duplex Stainless Steel

FBE

Fusion Bonded Epoxy

FBEL

Fusion Boned Epoxy Lined

FBEL CS

Fusion Boned Epoxy Lined Carbon Steel

FEED

Front End Engineering Design

FF

Flat Face

FG

Fuel/ Pilot Gas

FV

Full Vacuum

GC

Gathering Center

GTAW

Gas Tungsten Arc Welding

GY

Lean Glycol

HAZ

Heat Affected Zone

HIC

Hydrogen Induced Cracking

HSC

Hydrogen Stress Cracking


Page No : 6 of 237

KOC Contract No


14050489


Rev

50489-530-051-SPC-1002

B

HSE

Health, Safety & Environment

HSEMS

Health, Safety & Environment Management System

IG

Inert Gas

IN

Inhibitor / Injection Chemicals

ISO

International Organisation of Standardization

LEL CS

Liquid Epoxy Lined Carbon Steel

LPT/I/E

Liquid Penetrant Testing/Inspection/Examination

LSAW

Longitudinal Submerged Arc Welded

MAWP

Maximum Allowable Working Pressure

MAX

Maximum

MIN

Minimum

MOP

Maximum Operating Pressure

MPT/I/E

Magnetic Particle Testing/Inspection/Examination

MSS

Manufacturer’s Standardisation Society

NACE

National Association Of Corrosion Engineers

NDT/I/E

Non Destructive Testing/Inspection/Examination

Ni Al BRNZ

Nickel Aluminum Bronze

NPS

Nominal Pipe Size

OF

Fuel Oil or Diesel

OISD

Oil Industry Safety Directorate

OSHA

Occupational Safety & Health Administration

PC

Process Condensate

PG

Process Gas or Vapour

PL

Process Liquids

PMI

Positive Material Identification

PMS

Piping Material Specification

PREN

Pitting Resistance Equivalent Number

PO

Process Oil

PSI (g)

Pounds per Square Inch, Gauge, (Pressure Unit)

PWHT

Post Weld Heat Treatment

QAP

Quality Assurance Plan

QC & QA

Quality Control & Quality Assurance

RF

Raised Face

RT/I/E

Radiographic Testing/Inspection/Examination

RTJ

Ring Type Joint

RTRP

Reinforced Thermosetting Resin Pipe

SAW

Submerged Arc Welding

SCC

Stress Corrosion Cracking


Page No : 7 of 237

KOC Contract No


14050489


Rev

50489-530-051-SPC-1002

B

SCRM

Screwed Male

SCRF

Screwed Female

SDSS

Super Duplex Stainless Steel

SOHIC

Stress Oriented Hydrogen Induced Cracking

SS

Stainless Steel

SSC

Sulfide Stress Cracking

SW, SWE

Socket Weld, Socket Weld End

TEMP

Temperature

TPIA

Third Party Inspection Agency

UNS

Unique Numbering System

UT/I/E

Ultrasonic Testing/Inspection/Examination

VA

Vent to Atmosphere

VMS

Valve Material Specification

WD

Drinking Water

WE

Effluent Water

WF

Fire Water

WO

Oily/ Hydrocarbon Water

WP

Produced Water

WPS

Welding Procedure Specification

WRC

Welding Research Council

WT

Treated Effluent Water

WW

Well/ Wash Water

XG

Foam

4.0

REFERENCE STANDARDS, CODES AND SPECIFICATIONS

4.1

LIST OF STANDARD AND CODES For additional information concerning Pressure I Temp ratings, sizes, dimensions, tolerances, materials types, grades of Pipes, Fittings, Flanges, Bolts, Nuts, Valves etc. specified in this specification, the latest edition of following standards, codes and specifications may be consulted as required.

4.1.1

National / International Standards API SPEC 5L

Specification for Line Pipe

API 6D / ISO 14313

Specification for Pipeline Valves

API SPEC 6FA

Specification for Fire Test for valves

API 594

Check Valves: Flanged, Lug, Wafer and Butt Welding

API 598

Valve Inspection and Testing



Rev

50489-530-051-SPC-1002

B


14050489

API 599

Metal Plug Valves-Flanged, Threaded and Welding Ends

API 600/ ISO 10434

Steel Gate Valves-Flanged and Butt-welding Ends, Bolted Bonnets Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the Petroleum and Natural Gas Industries Fire Test for Quarter-turn Valves and Valves Equipped with Non-metallic Seats Metal Ball Valves – Flanged, Threaded and Welding Ends

API 602/ ISO 15761 API 607 API 608 API 609

Butterfly Valves: Double Flanged, Lug and Wafer Type

ASME B1.20.1

Pipe Threads, General Purpose (Inch)

ASME B16.5

Pipe Flanges and Flanged Fittings, NPS ½ through NPS 24

ASME B16.9

Factory-Made Wrought Butt welding Fittings

ASME B16.10

Face to Face and End to End dimensions of Valves

ASME B16.11

Forged Fittings, Socket Welding and Threaded

ASME B16.20

Metallic Gaskets for Pipe Flanges Ring Joint, Spiral Wound and Jacketed

ASME B16.21

Non-metallic Flat Gaskets for Pipe Flanges

ASME B16.24

Cast Copper Alloy Pipe Flanges and Flanged Fittings Classes 150, 300, 600, 900, 1500 and 2500

ASME B16.25

Butt welding Ends

ASME B16.34

Valves Flanged, Threaded and Welding End

ASME B16.47

Large Diameter Steel Flanges NPS 26 through NPS 60

ASME B18.2.1 ASME B18.2.2

Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and Lag Screws (Inch Series) Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts (Inch Series)

ASME B 31.3

Process Piping

ASME B36.10M

Welded and Seamless Wrought Pipe

ASME B36.19M

Stainless Steel Pipe

ASME B46.1

Surface Texture, Surface Roughness, Waviness and Lay

ASME Sec VIII DIV-I

Boiler and Pressure Vessel Code

ASTM A105/ A105M

Standard Specification for Carbon Steel Forgings for Piping Application

ASTM A123

Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products.



14050489


Rev

50489-530-051-SPC-1002

B

ASTM A182/ A182M

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High Temperature Service

ASTM A193/ A193M

Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High Temperature Service Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service Standard Specification for Chromium and ChromiumNickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications

ASTM A194/ A194M ASTM A216/ A216M ASTM A234/ A234M ASTM A240/ A240M

ASTM A312/ A312M

Standard Specification for Seamless, Welded and Heavily Cold Worked Austenitic Stainless Steel Pipe

ASTM A320/ A320M

Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low Temperature Service

ASTM A351/ 351M

Standard Specification for Castings, Austenitic, for Pressure-Containing Parts

ASTM A370

Standard Test Methods and Definitions for Mechanical Testing of Steel Products

ASTM A388/ A388M ASTM A403/ A403M ASTM A515/ A515M ASTM A516/ A516M ASTM A671/ A671M ASTM A790/ A790M ASTM A815/ 815M ASTM A995/ A995M ASTM B61 ASTM B62

Standard Practice for Ultrasonic Examination of Heavy Steel Forgings Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings Carbon Steel Plate for Intermediate and Higher Temperature Service Standard Specification for Pressure Vessel Plate, Carbon Steel, for Moderate and Lower Temperature Service Standard Specification for Electric Fusion Welded Steel Pipe for Atmospheric and Lower Temperatures Standard Specification for Seamless and Welded Ferritic/ Austenitic Stainless Steel Pipe Standard Specification for Wrought Ferritic, Ferritic/ Austenitic, and Martensitic Stainless Steel Piping Standard Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel for Pressure Containing Parts Standard Specification for Steam or Valve Bronze Castings Standard Specification for Composition Bronze or Ounce Metal Casting


Page No : 10 of 237

KOC Contract No


Rev

50489-530-051-SPC-1002

B


14050489

ASTM B148

Standard Specification for Aluminum-Bronze Sand Castings

ASTM B366

Standard Specification for Factory made wrought Nickel and Nickel Alloy Fittings

ASTM B564

Standard Specification for Nickel Alloy Forgings

BS 1868

Specification for Steel Check Valves (Flanged and Butt Welding Ends) for Petroleum, Petrochemical and Allied Industries

BS 1873

Steel Globe and Globe Stop and Check Valves (Flanged and Butt-Welding Ends) for Petroleum, Petrochemical and Allied Industries.

BS 5353

Steel Plug Valves

BS EN 593

Butterfly Valves

BS EN 558 - 2

Industrial Valves Industrial valves - Face-to Face and Centre-to Face Dimensions of Metal Valves for use in Flanged Pipe Systems. Part 2: Class Designated Valves

BS EN 1759 - 1

Flanges and their joints – Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1 : Steel Flanges, NPS ½” to 24”

BS EN 1982

Copper and Copper Alloys - Ingots and Castings

BS EN 12165

Copper & Copper Alloys Wrought & Unwrought Forging Stock

BS EN 12420

Copper & Copper alloys Forgings

BS EN 12266

Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements-CORR 14505; May 23, 2003 Part 2: Tests, Test Procedures and Acceptance Criteria Supplementary Requirements

BS EN ISO 10434

Bolted Bonnet Steel Gate Valves for the Petroleum, Petrochemical and Allied Industries

BS EN ISO 10497

Testing of valves - Fire Type-Testing Requirements

BS EN ISO 15761

Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller, for The Petroleum and Natural Gas Industries

BS EN ISO 17292

Metal Ball Valves for Petroleum, Petrochemical and Allied Industries

BS EN ISO 1461

Hot Dip Galvanized Coatings on Fabricated Iron and Steel Articles-Specifications and Test Methods

MSS SP-25

Standard Marking System for Valves, Fittings, Flanges and Unions

MSS -SP-45

Bypass and Drain Connection


Page No : 11 of 237

KOC Contract No


14050489

Rev

50489-530-051-SPC-1002

B

MSS-SP-53

Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fitting and Other Piping Components – Magnetic Particle Examinations Method

MSS-SP-55

Quality Standard for Steel Castings for Valves, Flanges and Fitting and Other Piping Components – visual method for evaluation of surface irregularities.

MSS-SP-72

Ball valve with Flanged or Butt Welding Ends for General service Specification for High-Test , Wrought, Butt-Welding Fitting

MSS SP-75 MSS SP-80

Bronze gate, globe, angle and Check Valves

MSS SP-83

Class 3000 Steel Pipe Unions Socket Welding and Threaded

MSS SP-97

Integrally Reinforced Forged Branch Outlet Fittings – Socket Welding, Threaded and Butt Welding Ends

MSS SP-110

Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends

NACE MR 0175 / ISO 15156

Petroleum and natural gas Industries - Materials for use in H2S containing environments in oil and gas production Parts 1 to 3, including: Part 1 Technical Corrigendum 1 published 01/09/2005; Part 2 Technical Corrigendum 1 published 01/09/2005; Part 3 Technical Corrigendum 1 published 15/02/2005; Part 3 Technical Corrigendum 2 published 01/09/2005. Evaluating Elastomeric Materials in Sour Gas Environment

NACE TM 0187 NACE TM 0284 NACE TM 0177 PFI ES-24 4.1.2


Evaluation of Pipeline and Pressure Vessel Steels for Resistance to Hydrogen Induced Cracking Laboratory Testing of Metals for Resistance to Sulfide Stress Cracking and Stress Corrosion Cracking in H2S Environments Pipe Bending Methods, Tolerances, Process and Material Requirements"

KOC Standards and Engineering Group Specifications Piping design and materials covered by this specification shall comply with all the applicable sections of KOC Standards and Specifications their addendum and criteria of which the following are specifically referenced in this specification EF1902-KOC-I-010-CRT-DGO

Criteria to KOC-I-010 : Control and Shut Down Valves

EF1902-KOC-MP-010-CRT-DE2

Criteria to KOC-MP-010 : Piping Material Classes

EF1902-015-JH-1903-ADD-DGO

Addendum to 015-JH-1903 : General Instrument

EF1902-015-LH-1002-ADD-DE2

Addendum to 015-LH-1002 : Piping Design

EF1902-KOC-MP-013-CRT-DE2

Criteria to KOC-MP-013 : KOC Standard for Gate Valves


Page No : 12 of 237

KOC Contract No


14050489

EF1902-KOC-MP-014-CRT-DE2 EF1902-KOC-MP-015-CRT-DE2 EF1902-KOC-MP-016-CRT-DE2 EF1902-KOC-MP-033-CRT-DE2 KOC-G-004

Rev

50489-530-051-SPC-1002

B

Criteria to KOC-MP-014 : KOC Standard for Globe Valves Criteria to KOC-MP-015 : KOC Standard for Check Valves Criteria to KOC-MP-016 : KOC Standard for Plug Valves Criteria to KOC-MP-033 : KOC Standard for Ball Valves KOC Standard for Packing, Marking and Documentation

KOC-G-007

KOC Standard for Basic Design Data.

KOC-I-0101

KOC Standard for Control and Shut Down Valves

KOC-MP-010

KOC Standard for Piping Material Classes

KOC-MP-013

KOC Standard for Gate Valves

KOC-MP-014

KOC Standard for Globe Valves

KOC-MP-015

KOC Standard for Check Valves

KOC-MP-016 / KOC-MP-033, Part-5 KOC-MP-031,Part 1 KOC-MP-031,Part 2

Design and Materials KOC Standard for Plug Valves KOC Standard for Gaskets for Pipe Flanges: Types, Design and Materials KOC Recommended Practice for Gaskets for Pipe Flanges: Selection Criteria, Handling and Installation

KOC-MP-033,Part 1

KOC Standard for Ball Valves

KOC-P-001

015-JH-1903

KOC Standard for Painting and Coating of External Metal Surfaces KOC Standard For Colour Coding of Pipework for Identification of Fluids & Services KOC Standard for QA / QC Requirements for Projects KOC Standard for Positive Material Identification (PMI) General Instrument

015-LH-1002

Piping Design

015-WH-1003

Inspection of Casting for General Pressure Service

KOC-P-017 KOC-Q-014 KOC-Q-015

4.1.3


Project Specific Documents 50489-530-051-SPC-1001

Piping Material Specification

50489-530-020-DIA-1002

Material Selection Diagram

50489-530-020-LST-1002

Line List



14050489

5.0


Rev

50489-530-051-SPC-1002

B

ENVIRONMENTAL CONDITIONS Environmental requirements to be considered with respect to piping design shall be established from KOC Standard KOC-G-007, entitled “KOC Standard for Basic Design Data”.

6.0

UNITS OF MEASUREMENT The metric units of measure shall be used throughout with the following exceptions: 1) Nominal pipe size (NPS) expressed in inches. 2) Nominal pressure ratings for Flanges, Valves are defined as per ASME B16.5, Class rating for socket weld and threaded end connections shall be series 3000# etc. as per ASME B16.11.

7.0

GENERAL REQUIREMENT

7.1

Valve shall be designed, manufactured, tested, inspected and marked as per the manufacturing standards; design codes and project specifications (latest editions) indicated in the respective valve data sheets. In case of a conflict between the KOC Standards (Refer Clause 4.1.2) & valve data sheets, valve data sheets shall govern over respective standards. Approval of drawings shall be valid only for design / constructional features.

7.2

Vendor shall quote in strict accordance with the valve specification sheets, technical notes and all other referred documents. Deviations to the specification sheets, technical notes etc., if any, shall be asked specifically.

7.3

All codes and standards for manufacturing, testing, inspection etc. shall be of latest edition of such documents.

7.4

All flanged valves shall have flanges integral (except forged valves) with the valve body. Flange face finish shall be normally specified in the valve specification sheet as smooth finish, 125 AARH etc. The interpretation for range of face finish shall be as follows: Serrated Finish / Smooth Finish/125AARH : 125 to 250 µin AARH (For RF Flanges) Extra smooth finish/63 AARH

7.5

: 32-63 µin AARH (For RTJ Flanges)

Valve body / bonnet shall be forged / cast as specified. Forgings are acceptable in place of castings but not vice-versa.


14050489

7.6



Rev

50489-530-051-SPC-1002

B

If an overlay weld-deposit is used for the body seat ring, seating surface, the corrosion resistance of the seat ring base material shall be at least equal to the corrosion resistance of the material of the shell / Body

7.7

Threaded Seat rings shall be screwed in place to prevent loosening. This may be done by Tack welding.

7.8

Manual gear operators shall be provided for frequently operated gate and globe valves in the ratings and sizes listed below:

7.9

7.10

Rating

Size

Class 150

12 in and larger

Class 300

10 in and larger

Class 600

6 in and larger

Class 900

4 in and larger

Gear operators shall be provided for Ball Valves in the sizes listed below: Rating

Size

Class 150

6 in and larger

Class 300

6 in and larger

Class 600

6 in and larger

Class 900

4 in and larger

Gear operators shall be provided for Plug Valves in the sizes listed below: Rating

Size

Class 150

8 in and larger

Class 300

8 in and larger

Class 600

6 in and larger

Class 900

6 in and larger

7.11

Globe Valves are to be used for throttling only.

7.12

All Butterfly Valves 8 in. and larger shall be provided with a gear operator.

7.13

Following requirement for check valves should be met over and above the valve spec sheet requirements: Wherever check valve disc assembly is supported from the cover of the check valves, the following shall be ascertained:


Page No : 15 of 237

KOC Contract No


14050489

−


Rev

50489-530-051-SPC-1002

B

Positive location / positioning of cover must be provided to ensure correct alignment of the valve disc.

−

Hinge pin design must permit accurate alignment of the disc and valve seat.

7.14

Wherever Ball valve is provided, they shall be full bore type

7.15

Ball Valves shall be provided with Lock open / Lock closed provision

7.16

Soft-seated SW end ball valves shall have a 150 mm long seamless pipe nipple welded to each end of the valve. Nipples are to be welded prior to valve assembly. Nipple specifications shall be as per Appendix III.

7.17

Each Ball and Plug valve shall be supplied with a lever / wrench except for gear operated / motor operated valves

7.18

The ball of ball valve shall not protrude outside the end flanges of valve.

7.19

Limit Switch requirements on applicable Plug valves shall be specified in BOQ. Specification of Limit switch for manually operated ON / OFF Valves shall be as per KOC-I-0101 (Rev 1) and its criteria (EF1902-KOC-I-0101-CRT-DGO)

7.20

Stem shall be forged or machined from forged / rolled bar. No casting is permitted. However, integral stem of cast stainless steel ball valve is acceptable. Stems shall be free of scratches, dents or other types of damage.

7.21

Body, Bonnet and Cover Bolts on valves shall be tightened with torque wrenches so that installed stress shall not be greater than 276 N / square mm.

7.22

All hardfacing / stellite facing shall be with Stellite No.6 or equal, having a minimum deposit thickness after final machining of 1.5 mm, unless otherwise approved by KOC. Iron content in the hardfacing due to base metal dilution shall not exceed 12%.

7.23

Gasket and Valve Stem Packing a) Spiral wound bonnet gaskets are to be provided with inner / outer ring except when encapsulated gasket type body-bonnet joints are employed. Outer ring may be avoided in case of non-circular spiral wound gasket used in 150# valve provided the outermost layer of spiral touches the bolts ascertaining the centering. Gasket surfaces (Bonnet and End connections) shall have no scratches, pin holes, dents or other type of damage. b) Valve stem packing shall be of non-asbestos material that is fire safe and shall contain inhibitors to prevent valve stem pitting. Valve stem packing shall comply to the following, as applicable:



14050489

•


Rev

50489-530-051-SPC-1002

B

Bronze Valves. Packing shall be in accordance with the Manufacturer’s standards.

•

Carbon Steel and Stainless Steel Valves. Valve packing shall be of non-asbestos material and fire safe. Packing shall be a five ring packing system consisting of three graphoil pre compressed and die-formed packing rings with graphite fiber top and bottom stem wiper rings. The packing shall contain a corrosion inhibitor to prevent valve stem pitting.

c) Asbestos in any form shall not be used 7.24

All other technical requirements which are not covered under this specification shall be as per applicable KOC valve standards referred in clause 4.1.2 of this specification.

8.0

TECHNICAL REQUIREMENTS

8.1

Manufacturing, Inspection and Testing of valves covered under this Valve Material Specifications shall be in full compliance with KOC Standards for valves and related addenda. All valves shall be Hydro / Pneumatic tested as per KOC standards for valves.

8.2

To have interchangeability of usage under different service conditions, all valves shall be procured with only Primer Coating applied. Primer coating shall be Inorganic Zinc Silicate. Finish paint of these valves shall be carried out after installation.

9.0

SOUR SERVICE REQUIREMENTS Material selection Guidelines per NACE MR 0175 / ISO 15156 as specified in Appendix II of KOC-MP-010 have been followed in this specification.

9.1

REQUIREMENTS FOR CARBON STEEL Materials intended to be used in sour service shall comply with the requirements of NACE MR 0175/ ISO 15156, and as supplemented in the following clauses: a) No cold forming/ bending shall be allowed b) Valve body, bonnet, disc, ball, stem etc. (all welded parts) shall have a maximum hardness of 235 BHN unless other values are specified in the applicable standards. c) All forgings shall be normalized.



Rev

50489-530-051-SPC-1002

B


14050489

9.2

Page No : 17 of 237

TECHNICAL REQUIREMENTS FOR STAINLESS STEELS AND OTHER CRA’S a) Stainless Steels and other CRA’s shall comply with NACE MR 0175/ ISO 15156 and Shall be suitable for the design conditions in respect of temperature, H2S partial pressure, chloride content and other applicable environmental parameters. b) Stainless steels shall be in solution annealed condition and shall meet the requirements of NACE MR0175/ ISO15156. c) The use of cold worked stainless steels is subject to the limitations imposed by NACE MR0175/ ISO15156.

9.3

WELDING Wherever weld overlay with CRA material is specified for valve components, the following conditions shall apply: (i)

The procedure/ methodology adopted shall be weld-overlay specific.

(ii)

In case of manual / automatic weld overlay process, the minimum weld overlay thickness required after machining shall be 3 mm.

(iii)

The required CRA deposit shall be obtained through a minimum of three passes.

(iv)

The machined surface of the valve component shall undergo PMI test to verify the major alloying elements.

(v)

Where barrier layer is applied prior to the overlay, the PMI results shall meet the specification of the filler rod, (for example SS316L).

(vi)

For other alloys where no barrier layer is applied, PMI results shall meet the specification of CRA material.

(vii)

The finished surface of the components shall undergo LPT and shall be free of any surface opening defects.

(viii) The weld overlay, wherever recommended, shall be done by either SS316L or 6 Mo or Inconel 625 materials. However Duplex SS and / or Super Duplex SS shall not be used for weld overlay.

10.0 INSPECTION AND TESTING REQUIREMENTS Apart from the Inspection and Testing requirements mentioned in respective KOC Standards for Valves, the following requirements shall be adhered to: a) All items and their parts shall be subjected to all mandatory as well as supplementary (wherever specified) inspections, tests and checks called-for in the respective codes/ standards & specifications/ data sheets. b) All inspection work shall be carried out in line with KOC Standard for Project QA/QC requirement, Doc. No.KOC-Q-014.


Page No : 18 of 237

KOC Contract No


14050489


Rev

50489-530-051-SPC-1002

B

c) PMI-testing at vendor’s works shall be carried-out/ executed as per KOC standard for Positive Material Identification, Doc. No. KOC-Q-015. d) Further receipt of valve from vendor, all new manual / actuated (on / off) valves shall be subject to pressure testing in company approved workshop’s in Kuwait and witnessed by company. All testing shall be performed & witnessed by Company’s or Contractor’s representatives / nominated TPIA. In the event of failure of any new Valve during pressure testing, company reserve the right to reject the materials at no cost to company. The Company reserves the right to accept these valves as repaired or for them to be replaced at no extra cost to the Company.

11.0 NON DESTRUCTIVE EXAMINATION (NDE) REQUIREMENTS Non-Destructive examination of all valves shall be as per Para 9.8 of KOC Standard for Ball Valves- Part 1, Doc. No. KOC-MP-033 Part 1.

12.0 VALVE DATA SHEET NOMENCLATURE Each Valve data sheet number consists of at least five (5) digits. Suffix shall be added to the same depending upon the optional requirement. a) The first two digit of the data sheet number defines the type of Valve: 51

Gate Valve

52

Globe Valve

53

Check Valve

54

Ball Valve

55

Plug Valve

56

Butterfly Valve

57

Needle Valve

b) The third digit of the data sheet number defines the valve rating 0 3 4

800# 150# 300#

5 6 7

600# 900# 1500#

c) The last two digits of the data sheet number define the MOC/ valve metallurgy: 01

CS

11

Body : CS + Trim : Super Duplex, NACE


Page No : 19 of 237

KOC Contract No


14050489


Rev

50489-530-051-SPC-1002

B

12

Body : CS + Trim : SS316L, NACE

61

SS316 / 316L

63

Body : SS316 / 316L + Trim : Super Duplex, NACE

64

Body : SS316 / 316L + Trim : SS316L, NACE

78

NI-AL-Bronze

79

Super Duplex SS, NACE

80

Bronze

81

CS ( EPDM Lined) + Trim : Monel / Ni-Al-Bronze

82

Super Duplex SS

90

CS ( EPDM Lined) + Trim : Super Duplex SS, NACE

98

CS (Inconel Lined) + Trim : Inconel, NACE

99

Inconel 625, NACE

d) The suffix to the five digit data sheet number defines specific / special requirements (optional): B

Butt weld

D

Dual Plate Check Valve

F

Flat Face

L

Limit Switch arrangement

P

Piston Type (Flanged Only)

S

SCRF

X

SW x SCRF

Y

Ball Valve spring loaded)

Z

Swing Type (SW Only)



14050489


Rev

50489-530-051-SPC-1002

B

APPENDIX - I TABLE - 1 : VALVE DATA SHEET INDEX

SR. NO.

SHEET NO.

1

51001

2

51001X

MATERIAL OF CONSTRUCTION

PIPING CLASS

VALVE TYPE

SIZE RANGE (INCH)

RATING

C13A

Gate

0.5 - 1.5

C13A

Gate

S10A, S30A, S60A S10A, S30A, S60A

END Remarks CONNECTION

BODY

TRIM

800#

Carbon Steel

Stellited

SW

0.5 - 1.5

800#

Carbon Steel

Stellited

SW X SCRF

Gate

0.5 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW

Gate

0.5 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW X SCRF

3

51061

4

51061X

5

51082

Q35A, F30A

Gate

0.5 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW

6

51082X

Q35A, F30A

Gate

0.5 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW X SCRF

7

51301

C13A

Gate

2 - 16

150#

Carbon Steel

13 % Chrome

RF

8

51311

C15B

Gate

0.5 - 48

150#

Carbon Steel

Super Duplex SS

RF

NACE

9

51312

C15B

Gate

0.5 - 48

150#

Carbon Steel

SS316L

RF

NACE

10

51361

S10A

Gate

2 - 12

150#

SS316

SS316 / 316L

RF

0.5 - 1.5

150#

SS316 / 316L

Super Duplex SS

RF

11

51363

S10B

Gate 2 - 12

150#

SS316

Super Duplex SS

RF

0.5 - 1.5

150#

SS316 / 316L

SS316L

RF

2 - 12

150#

SS316

SS316L

RF

12

51364

S10B

NACE

Gate

NACE

13

51378

Q15A

Gate

3 - 24

150#

NI-AL Bronze

Monel / NI-AL Bronze

RF

14

51378F

C13B, F10A

Gate

2 - 24

150#

NI-AL Bronze


FF

15

51379

Q15B, F10B, C15B

Gate

0.5 - 36

150#

Super Duplex SS

Super Duplex SS

RF

NACE

16

51379F

F10B

Gate

2 - 36

150#

Super Duplex SS

Super Duplex SS

FF

NACE

17

51380F

F10A, Q15A

Gate

0.5 - 2

150#

Bronze

Bronze

FF

18

51380S

C13B

Gate

0.5 - 3

150#

Bronze

Bronze

SCRF

19

51398

N10C

8 - 16

150#

CS Inconel Lined

Inconel

RF

NACE

Gate

0.5 - 20

150#

Inconel

Inconel

RF

NACE NACE

B

20

51399

N10B, N10C

21

51411

C35B

Gate

0.5 - 16

300#

Carbon Steel

Super Duplex SS

RF

22

51461

S30A

Gate

2 - 12

300#

SS316

SS316 / 316L

RF

0.5 - 1.5

300#

SS316 / 316L

Super Duplex SS

RF

23

51463

S30B

Gate 2 - 16

300#

SS316

Super Duplex SS

RF

NACE

24

51478

Q35A

Gate

3 - 32

300#

NI-AL Bronze


RF

25

51478F

F30A

Gate

2 - 24

300#

NI-AL Bronze


FF

26

51479

C35B, F30B, S30B, Q35B

Gate

0.5 - 24

300#

Super Duplex SS

Super Duplex SS

RF

NACE

27

51479F

F30B

Gate

2 - 24

300#

Super Duplex SS

Super Duplex SS

FF

NACE

28

51482

Q35A

Gate

2

300#

Super Duplex SS

Super Duplex SS

RF

Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No VALVE MATERIAL SPECIFICATION

14050489


Rev

50489-530-051-SPC-1002

B


SR. NO.

SHEET NO.

PIPING CLASS

VALVE TYPE

SIZE RANGE (INCH)

RATING BODY

TRIM

29

51498

N30C

Gate

8 - 16

150#

CS Inconel Lined

Inconel

RF

NACE

30

51499

N30B, N30C

Gate

0.5 - 16

300#

Inconel

Inconel

RF

NACE

31

51511

C65B

Gate

0.5 - 24

600#

Carbon Steel

Super Duplex SS

RF

NACE

32

51561

S60A

Gate

2 - 12

600#

SS316

SS316 / 316L

RF

33

51579

C65B

Gate

0.5 - 24

600#

Super Duplex SS

Super Duplex SS

RF

NACE

34

51779

Q95B

Gate

0.5 - 2

1500#

Super Duplex SS

Super Duplex SS

RF

NACE

35

52001

C13A

Globe

0.5 - 1.5

800#

Carbon Steel

Stellited

SW

36

52061

S10A, S30A, S60A

Globe

0.5 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW

37

52082

F30A, Q35A

Globe

0.5 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW

38

52301

C13A

Globe

2 - 16

150#

Carbon Steel

13 % Chrome

RF

39

52311

C15B

Globe

0.5 - 16

150#

Carbon Steel

Super Duplex SS

RF

NACE

40

52312

C15B

Globe

0.5 - 16

150#

Carbon Steel

SS316L

RF

NACE

41

52361

S10A

Globe

2 - 12

150#

SS316

SS316 / 316L

RF

0.5 - 1.5

150#

SS316 / 316L

Super Duplex SS

RF

42

52363

S10B

Globe 2 - 12

150#

SS316

Super Duplex SS

RF

0.5 - 1.5

150#

SS316 / 316L

SS316L

RF

2 - 12

150#

SS316

SS316L

RF

43

52364

B

S10B


NACE

Globe

NACE

44

52378

Q15A

Globe

3 - 16

150#

NI-AL Bronze


RF

45

52378F

C13B, F10A

Globe

2 - 16

150#

NI-AL Bronze


FF

46

52379

Q15B, F10B, C15B

Globe

0.5 - 16

150#

Super Duplex SS

Super Duplex SS

RF

NACE

47

52379F

F10B

Globe

2 - 16

150#

Super Duplex SS

Super Duplex SS

FF

NACE

48

52380F

F10A, Q15A

Globe

0.5 - 2

150#

Bronze

Bronze

FF

49

52380S

C13B

Globe

0.5 - 3

150#

Bronze

Bronze

SCRF

50

52399

N10B, N10C

Globe

0.5 - 16

150#

Inconel

Inconel

RF

NACE

51

52411

C35B

Globe

0.5 - 12

300#

Carbon Steel

Super Duplex SS

RF

NACE

52

52461

S30A

Globe

2 - 12

300#

SS316

SS316 / 316L

RF

0.5 - 1.5

300#

SS316 / 316L

Super Duplex SS

RF

53

52463

S30B

Globe 2 - 12

300#

SS316

Super Duplex SS

RF

B

NACE

54

52478

Q35A

Globe

3 - 12

300#

NI-AL Bronze


RF

55

52478F

F30A

Globe

2 - 12

300#

NI-AL Bronze


FF

56

52479

Q35B, F30B, C35B

Globe

0.5 - 12

300#

Super Duplex SS

Super Duplex SS

RF

NACE

57

52479F

F30B

Globe

2 - 16

300#

Super Duplex SS

Super Duplex SS

FF

NACE



14050489


Rev

50489-530-051-SPC-1002

B


SR. NO.

SHEET NO.

PIPING CLASS

VALVE TYPE

SIZE RANGE (INCH)

RATING BODY

TRIM

58

52482

Q35A

Globe

2

300#

Super Duplex SS

Super Duplex SS

RF

59

52499

N30B, N30C

Globe

0.5 - 12

300#

Inconel

Inconel

RF

NACE

60

52511

C65B

Globe

0.5 - 12

600#

Carbon Steel

Super Duplex SS

RF

NACE

61

52561

S60A

Globe

2 - 12

600#

SS316

SS316 / 316L

RF

62

52579

C65B

Globe

2-6

600#

Super Duplex SS

Super Duplex SS

RF

63

53001

C13A

Check

0.5 - 1.5

800#

Carbon Steel

Stellited

SW

64

53061

S10A, S30A, S60A

Check

0.5 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW

65

53061Z

S30A, S60A

Check

0.5 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW

66

53082

F30A, Q35A

Check

0.5 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW

67

53301

C13A

Check

2 - 16

150#

Carbon Steel

13 % Chrome

RF

68

53311P

C15B

Check

0.5 - 1.5

150#

Carbon Steel

Super Duplex SS

RF

NACE

69

53311

C15B

Check

2 - 48

150#

Carbon Steel

Super Duplex SS

RF

NACE

70

53312P

C15B

Check

0.5 - 1.5

150#

Carbon Steel

SS316L

RF

NACE

71

53312

C15B

Check

2 - 48

150#

Carbon Steel

SS316L

RF

NACE

72

53361

S10A

Check

2 - 12

150#

SS316

SS316 / 316L

RF

73

53363P

S10B

Check

0.5 - 1.5

150#

SS316 / 316L

SS316 / 316L

RF

NACE

74

53363

S10B

Check

2 - 12

150#

SS316

SS316 / 316L

RF

NACE

75

53364P

S30B

Check

0.5 - 1.5

150#

SS316 / 316L

SS316 / 316L

RF

NACE

76

53364

S30B

Check

2 - 12

150#

SS316

SS316 / 316L

RF

NACE

77

53378D

Q15A

Check

3 - 24

150#

NI-AL Bronze


RF

78

53378DF

C13B, F10A

Check

2 - 24

150#

NI-AL Bronze


FF

79

53379P

F10B, Q15B

Check

0.5 - 1.5

150#

Super Duplex SS

Super Duplex SS

RF

NACE

80

53379D

Q15B

Check

2 - 36

150#

Super Duplex SS

Super Duplex SS

RF

NACE

81

53379DF

F10B

Check

2 - 36

150#

Super Duplex SS

Super Duplex SS

FF

NACE

82

53380P

F10A, Q15A

Check

0.5 - 2

150#

Bronze

Bronze

FF

83

53380S

C13B

Check

0.5 - 3

150#

Bronze

Bronze

SCRF

84

53399P

N10B, N10C

Check

0.5 - 2

150#

Inconel

Inconel

RF

NACE

85

53399D

N10B, N10C

Check

3 - 20

150#

Inconel

Inconel

RF

NACE

B

B


NACE

B

86

53411P

C35B

Check

0.5 - 1.5

300#

Carbon Steel

Super Duplex SS

RF

NACE

87

53411

C35B

Check

2 - 16

300#

Carbon Steel

Super Duplex SS

RF

NACE

88

53461

S30A

Check

2 - 12

300#

SS316

SS316 / 316L

RF

89

53478

Q35A

Check

3 - 24

300#

NI-AL Bronze


RF



14050489


Rev

50489-530-051-SPC-1002

B


SR. NO.

SHEET NO.

PIPING CLASS

VALVE TYPE

SIZE RANGE (INCH)

RATING


BODY

TRIM

90

53478D

Q35A

Check

3 - 32

300#

NI-AL Bronze


RF

91

53479P

F30B, Q35B

Check

0.5 - 1.5

300#

Super Duplex SS

Super Duplex SS

RF

NACE

92

53479D

Q35B

Check

2 - 24

300#

Super Duplex SS

Super Duplex SS

RF

NACE

93

53482D

Q35A

Check

2

300#

Super Duplex SS

Super Duplex SS

RF

94

53498D

N30C

Check

8 - 16

300#

CS Inconel Lined

Inconel

RF

NACE

95

53499P

N30B, N30C

Check

0.5 - 2

300#

Inconel

Inconel

RF

NACE

Check

3 - 16

300#

Inconel

Inconel

RF

NACE

B

96

53499D

N30B, N30C

97

53511P

C65B

Check

0.5 - 1.5

600#

Carbon Steel

Super Duplex SS

RF

NACE

98

53511

C65B

Check

2 - 24

600#

Carbon Steel

Super Duplex SS

RF

NACE

99

53511D

C65B

Check

2 - 24

600#

Carbon Steel

Super Duplex SS

RF

NACE

100

53561

S60A

Check

2 - 12

600#

SS316

SS316 / 316L

RF

101

53679D

Q95B

Check

3 - 20

900#

Super Duplex SS

Super Duplex SS

RTJ

NACE

102

53779P

Q95B

Check

0.5 - 1.5

1500#

Super Duplex SS

Super Duplex SS

RTJ

NACE

103

53779D

Q95B

Check

2

1500#

Super Duplex SS

Super Duplex SS

RTJ

NACE

104

54001

C13A

Ball

0.5 - 1.5

800#

Carbon Steel

SS316L

SW

105

54001S

C13A

Ball

0.5

800#

Carbon Steel

SS316L

SCRM X SCRF

106

54001X

C13A

Ball

0.75 - 1.5

800#

Carbon Steel

SS316L

SW X SCRF

107

54061

Ball

0.5 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW

108

54061S

Ball

0.5

800#

SS316 / 316L

SS316 / 316L

SCRM X SCRF

109

54061X

Ball

0.75 - 1.5

800#

SS316 / 316L

SS316 / 316L

SW X SCRF

110

54082

F30A, Q35A

Ball

0.5 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW

111

54082Y

F30A

Ball

0.5 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW

112

54082S

F30A, Q35A

Ball

0.5

800#

Super Duplex SS

Super Duplex SS

SCRM X SCRF

113

54082X

F30A, Q35A

Ball

0.75 - 1.5

800#

Super Duplex SS

Super Duplex SS

SW X SCRF

114

54301

C13A

Ball

2 - 16

150#

Carbon Steel

SS316L

RF

115

54311

C15B

Ball

0.5 - 36

150#

Carbon Steel

Super Duplex SS

RF

NACE

116

54312

C15B

Ball

0.5 - 36

150#

Carbon Steel

SS316L

RF

NACE

117

54361

S10A

Ball

2 - 12

150#

SS316

SS316 / 316L

RF

0.5 - 1.5

150#

SS316 / 316L

Super Duplex SS

RF

118

54363

S10B

Ball 2 - 16

150#

SS316

Super Duplex SS

RF

0.5 - 1.5

150#

SS316 / 316L

SS316 / 316L

RF

2 - 12

150#

SS316

SS316 / 316L

RF

3 - 24

150#

NI-AL Bronze


RF

119

120

54364

54378

S10A, S30A, S60A S10A, S30A, S60A S10A, S30A, S60A

S10B

Q15A

NACE

Ball

Ball

NACE



14050489


Rev

50489-530-051-SPC-1002

B


SHEET NO.

PIPING CLASS

VALVE TYPE

SIZE RANGE (INCH)

RATING

121

54378F

C13B, F10A

Ball

2 - 24

122

54379

Q15B, F10B, C15B

Ball

123

54379F

F10B

124

54380F

125

SR. NO.

Page No : 24 of 237


BODY

TRIM

150#

NI-AL Bronze


FF

0.5 - 36

150#

Super Duplex SS

Super Duplex SS

RF

NACE

Ball

2 - 36

150#

Super Duplex SS

Super Duplex SS

FF

NACE

F10A, Q15A

Ball

0.5 - 2

150#

Bronze

Bronze / Monel

FF

54380YF

F10A

Ball

0.5 - 2

150#

Bronze

Bronze / Monel

FF

126

54380S

C13B

Ball

0.5 - 1.5

150#

Bronze

Bronze / NI-AL-Bronze

SCRF

127

54398

N10C

Ball

8 - 16

150#

CS Inconel Lined

Inconel

RF

NACE

128

54399

N10B, N10C

Ball

0.5 - 20

150#

Inconel

Inconel

RF

NACE

129

54411

C35B

Ball

0.5 - 14

300#

Carbon Steel

Super Duplex SS

RF

NACE

130

54461

S30A

Ball

2 - 12

300#

SS316

SS316 / 316L

RF

0.5 - 1.5

300#

SS316 / 316L

Super Duplex SS

RF

131

54463

S30B

Ball 2 - 12

300#

SS316

Super Duplex SS

RF

B

NACE

132

54478

Q35A

Ball

3 - 32

300#

NI-AL Bronze


RF

133

54478F

F30A

Ball

2 - 24

300#

NI-AL Bronze


FF

134

54479

C35B, F30B, Q35B

Ball

0.5 - 24

300#

Super Duplex SS

Super Duplex SS

RF

NACE

135

54479F

F30B

Ball

2 - 24

300#

Super Duplex SS

Super Duplex SS

FF

NACE

136

54498

N30C

Ball

8 - 16

300#

CS Inconel Lined

Inconel

RF

NACE

Ball

0.5 - 16

300#

Inconel

Inconel

RF

NACE NACE

B

137

54499

N30B, N30C

138

54511

C65B

Ball

0.5 - 24

600#

Carbon Steel

Super Duplex SS

RF

139

54561

S60A

Ball

2 - 12

600#

SS316

SS316 / 316L

RF

140

54579

C65B

Ball

0.5 - 6

600#

Super Duplex SS

Super Duplex SS

RF

NACE

141

54679

Q95B

Ball

3 - 24

900#

Super Duplex SS

Super Duplex SS

RTJ

NACE

142

54779

Q95B

Ball

0.5 - 2

1500#

Super Duplex SS

Super Duplex SS

RTJ

NACE

143

55411

C35B

Plug

0.5 - 12

300#

Carbon Steel

CS with Anti Friction Inpregnated

RF

NACE

144

55511

C65B

Plug

0.5 - 24

600#

Carbon Steel


RF

NACE

55511L

C65B

Plug

0.5 - 24

600#

Carbon Steel


RF

NACE

146

56311

C15B

Butterfly

3 - 24

150#

Carbon Steel

Super Duplex SS

RF

NACE

147

56312

C15B

Butterfly

3 - 24

150#

Carbon Steel

SS316L

RF

NACE

148

56381

Q15A

Butterfly

3 - 24

150#

CS EPDM Lined


RF

149

56478

Q35A

Butterfly

3 - 24

300#

NI-AL Bronze


RF

150

57082

Q35A

Needle

0.5

800#

Super Duplex SS

Super Duplex SS

SW

151

57311

C15B

Needle

0.5 - 1.5

150#

Carbon Steel

Super Duplex SS

RF

145

B

NACE



14050489


Rev

50489-530-051-SPC-1002

B


SR. NO.

SHEET NO.

PIPING CLASS

VALVE TYPE

SIZE RANGE (INCH)

RATING


BODY

TRIM

152

57312

C15B

Needle

0.5 - 1.5

150#

Carbon Steel

SS316L

RF

NACE

153

57379

Q15B

Needle

0.5 - 1.5

150#

Super Duplex SS

Super Duplex SS

RF

NACE

154

57411

C35B

Needle

0.5 - 1.5

300#

Carbon Steel

Super Duplex SS

RF

NACE


14050489



Rev

50489-530-051-SPC-1002

B

APPENDIX-II VALVE DATA SHEET: DETAIL DESCRIPTION All Valve data sheet shown in TABLE-2: Valve Data Sheet Index, are described in detail in the following pages.

SHEET NO.


51001

KOC Contract No VALVE MATERIAL SPECIFICATION

14050489 Piping Class Manuf. Standard Testing Standard

Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)

C13A

Size Range Rating Ends

Fuel Oil (Diesel), Inert Gas

SW, 3000# to ASME B16.11

ASME B 16.34

Face to Face dimension Manufacturer's Standard Air Test psi (g)

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements

Valve Type

API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1

2975 2175


80

Description

Type of Construction

Material of Construction

Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet

Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4) Bolted

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105

Bonnet Gasket

Spiral Wound

SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring

Manufacturer's Alternate/ Acceptance

Body Seat Ring Renewable / Integral 13% Cr. Steel + Stellite Facing Gate ( Wedge) Solid (Note 3) ASTM A 105 + Stellite Facing Body Forged ASTM A 105 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.

Page 27 of 237

SHEET NO.


51001X




C13A

Rev

50489-530-051-SPC-1002

B


Valve Type




SW X SCRD NPT(F), 3000# to ASME B16.11 Face to Face dimension Manufacturer's Standard

ASME B 16.34 2975 2175


Air Test psi (g)

80

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 193 Gr 2H ASTM A 105

Bonnet Gasket

Spiral Wound



Body Seat Ring Renewable / Integral 13% Cr. Steel + Stellite Facing Gate ( Wedge) Solid (Note 3) ASTM A 105 + Stellite Facing Body Forged ASTM A 105 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.

Page 28 of 237

SHEET NO.


51061



Services / Fluids

Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)

S10A, S30A, S60A


Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor

SW, 3000 # to ASME B16.11

ASME B 16.34

Face to Face dimension Manufacturer's Standard

2900 2125

Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type



80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C

Bonnet Gasket

Spiral Wound

SS 316/ 316L Dual Stamped Graphite with Inconel Wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 F 316/ 316L Dual Stamped


B


Body Seat Ring Renewable / Integral ASTM A 182 F 316/ 316L Dual Stamped Gate ( Wedge) Solid (Note 3) ASTM A 182 F 316/ 316L Dual Stamped Body Forged ASTM A 182 F 316/ 316L Dual Stamped GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 29 of 237

SHEET NO.


51061X



Services / Fluids


S10A, S30A, S60A



B

SW X SCRD NPT(F), 3000# to ASME B16.11


ASME B 16.34 2900 2125

Rev

50489-530-051-SPC-1002 GATE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements

Valve Type



Air Test psi (g)

80

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C

Bonnet Gasket

Spiral Wound

SS 316/ 316L Dual Stamped Graphite with Inconel Wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 F 316/ 316L Dual Stamped


B


Body Seat Ring Renewable / Integral ASTM A 182 F 316/ 316L Dual Stamped Gate ( Wedge) Solid (Note 3) ASTM A 182 F 316/ 316L Dual Stamped Body Forged ASTM A 182 F 316/ 316L Dual Stamped GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 30 of 237



Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description

Q35A, F30A


Brackish Water

SW, 3000 # to ASME B16.11

ASME B 16.34



Air Test psi (g)

51082 Contractor Document Number

Rev

50489-530-051-SPC-1002

B


Valve Type


3000 2200

SHEET NO.

80 Material of Construction


Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C Stem Sleeve/ Nut Forged/ Machined Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel Wire Back Seat Bush UNS S32750/ 32760 Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M B Bonnet Bolted ASTM A 182 Gr F 53 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable / Integral UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Forged ASTM A 182 Gr F 53 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 31 of 237




Q35A, F30A


Brackish Water

SW X SCRD NPT(F), 3000# to ASME B16.11

3000 2200 Type of Construction

51082X Contractor Document Number

Rev

50489-530-051-SPC-1002

B


Valve Type


ASME B 16.34

SHEET NO.

Face to Face dimension Manufacturer's Standard Air Test psi (g)



Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel Wire Back Seat Bush UNS S32750/ 32760 B Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolted ASTM A 182 Gr F 53 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable / Integral UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Forged ASTM A 182 Gr F 53 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 32 of 237

SHEET NO.


51301




C13A



Flanged, 150#, ASME B16.5, RF, Finish 125 AARH

ASME B 16.34

Face to Face dimension ASME B 16.10

450 325

Air Test psi (g)

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements

Valve Type



80

Description





Bonnet Gasket

Spiral Wound

Body Seat Ring

Renewable

Gate ( Wedge)

Solid (Note 3)

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 216 Gr WCB SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring 13% Cr. Steel (2" - 6") A 105 + 13% Cr. Steel Deposit (8" - 16") 13% Cr. Steel/ ASTM A 216 Gr WCB + 13% Cr. Steel Deposit ASTM A 216 Gr WCB


Cast Body GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.

Page 33 of 237

SHEET NO.


51311


14050489

Manuf. Standard

Testing Standard


API 602/ BS EN ISO 15761 (1/2" - 1 1/2") , API 600/BS EN ISO 10434 ( 2" - 24"), API 6D / ASME B 16.34 (26" - 48") API 598/ BS 6755 Pt. 1

B

Valve Type Bolted Bonnet

Size Range

1/2" - 48"

Rating Ends

150# Special Requirements

Hydrocarbon Gas/ Oil/ Condensate, Glycol

Flanged, 150#, ASME B16.5/ B 16.47 Series A, RF, Finish 125 AARH

ASME B 16.34


450 325

Rev

50489-530-051-SPC-1002 GATE VALVE OS &Y

C15B

Piping Class


Air Test psi (g)

1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

80

Description



Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts

Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream (Note 4)

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750 / 32760 Graphite with Inconel wire UNS S32750 / 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H

Bonnet

Bolted

ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 48")

Bonnet Gasket

Spiral Wound


Body Seat Ring

Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 48")

UNS S32750 / 32760

Gate ( Wedge)

Solid (Note 3)

UNS S32750 / 32760

Body

Forged, Cast



Page 34 of 237

Project Title NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No 14050489


SHEET NO. 51311 Contractor Document Number

Rev

50489-530-051-SPC-1002

B

GATE VALVE GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.

Page 35 of 237

SHEET NO.


51312


14050489 Piping Class

Manuf. Standard

OS &Y Bolted Bonnet

Size Range

1/2" - 48"

Rating


API 598/ BS 6755 Pt. 1

Services / Fluids



ASME B 16.34


Ends

1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.

80

Air Test psi (g)

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS316L Graphite with Inconel wire SS316L ASTM A 193 Gr B7 ASTM A 194 Gr 2H

Bonnet

Bolted


Bonnet Gasket

Spiral Wound


Gate ( Wedge)

Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 48") Solid (Note 3)

Body

Forged, Cast

Body Seat Ring

B

Valve Type

API 602/ BS EN ISO 15761 (1/2" - 1 1/2") , API 600/BS EN ISO 10434 ( 2" - 24"), API 6D / ASME B 16.34 (26" - 48")

450 325

Rev

50489-530-051-SPC-1002 GATE VALVE

C15B

Testing Standard




SS316L SS316L ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 48")

Page 36 of 237




Rev

50489-530-051-SPC-1002

B

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor.

Page 37 of 237

SHEET NO.


51361



Services / Fluids


S10A

Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution


B



ASME B 16.34 425 325

Rev

50489-530-051-SPC-1002 GATE VALVE OS &Y Bolted Bonnet 2" - 12" 150# Special Requirements

Valve Type



Air Test psi (g)

80

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M

Bonnet Gasket

Spiral Wound



B

Body Seat Ring Renewable SS316 Gate ( Wedge) Solid (Note 3) SS316 Body Cast ASTM A 351 Gr CF8M GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 38 of 237

SHEET NO.


51363


14050489

Valve Type

Manuf. Standard

Testing Standard

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

S10B

Piping Class


Bolted Bonnet

API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434( 2" - 12") API 598/ BS 6755 Pt. 1

Size Range

1/2" - 12"

Rating Ends

150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

Services / Fluids


Hydrocarbon Gas / Condensate, Glycol


ASME B 16.34


425 325

Air Test psi (g)

80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream -

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750 / 32760 Graphite with Inconel wire UNS S32750 / 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bonnet

Bolted

A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 12")

Bonnet Gasket

Spiral Wound


Gate ( Wedge)

Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 12") Solid (Note 3)

Body

Forged,Cast

Body Seat Ring


B

UNS S32750 / 32760 UNS S32750 / 32760 A182 Gr F316/316L Dual Stamped (1/2" - 1 1/2") ASTM A 351 Gr CF8M (2" - 12")

Page 39 of 237




Rev

50489-530-051-SPC-1002

B

GENERAL NOTES : GATE VALVE 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 40 of 237

SHEET NO.


51364


14050489

Valve Type Manuf. Standard

Testing Standard

Services / Fluids


API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434( 2" - 12")

Size Range

1/2" - 12"

Rating Ends


1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) Flanged, 150#, ASME B16.5, RF, Finish 125 & Fuel Gas (FG) services only.

AARH


ASME B 16.34 425 325

B

Bolted Bonnet

API 598/ BS 6755 Pt. 1


Rev

50489-530-051-SPC-1002 GATE VALVE OS &Y

S10B

Piping Class


Air Test psi (g)

80

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bonnet

Bolted


Bonnet Gasket

Spiral Wound


Body Seat Ring


316/316L Dual Stamped (1/2" - 1 1/2") SS316L (2" - 12")

Gate ( Wedge)

Solid (Note 3)

316/316L Dual Stamped (1/2" - 1 1/2") SS316L (2" - 12")

Body

Forged,Cast



B

Page 41 of 237




Rev

50489-530-051-SPC-1002

B

GENERAL NOTES : GATE VALVE 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 42 of 237



Q15A


Rev

50489-530-051-SPC-1002

B

Valve Type

GATE VALVE OS &Y Bolted Bonnet

Manuf. Standard

API 600/ BS EN ISO 10434

Size Range

3" - 24"

Testing Standard

BS 5154/ MSS-SP-80

Rating Ends


Services / Fluids

Brackish Water


ASME B 16.24

Face to Face dimension BS 5154

Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description


Air Test psi (g)



Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) Monel / NI-AL-Bronze Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush Monel / NI-AL-Bronze Bonnet Bolts / Nuts (Note 6) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM B 148 UNS C95800 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable Monel / NI-AL-Bronze Gate ( Wedge) Solid (Note 5) Monel / NI-AL-Bronze Body Cast ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 4. Care should be taken to avoid galvanic corrosion by dissimlar metals. 5. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 6. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 7. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.

Page 43 of 237

SHEET NO.


51378F



C13B (4" - 12"), F10A (2" - 24")

Valve Type


Testing Standard

BS 5154/ MSS-SP-80


Services / Fluids

Brackish Water, Potable/ Fresh Water, Plant Air

Flanged, 150#, ASME B16.5, FF, Finish 125 AARH

ASME B 16.24


Description


Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Manuf. Standard





Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) Monel / NI-AL-Bronze Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush Monel / NI-AL-Bronze (Note 9) Bonnet Bolts / Nuts (Note 6) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM B 148 UNS C95800 Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable Monel / NI-AL-Bronze (Note 9) Gate ( Wedge) Solid (Note 5) Monel / NI-AL-Bronze (Note 9) Body Cast ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 4. Care should be taken to avoid galvanic corrosion by dissimlar metals. 5. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 6. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 7. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor. 9. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .

B

Page 44 of 237

SHEET NO.


51379



Manuf. Standard

Bolted Bonnet

Size Range

1/2" - 36" 150# Special Requirements

Rating Ends

Services / Fluids

Potable/ Fresh Water, Plant Air, Hydrocarbon Oil/ Condensate, Oily Water, Effluent Water


ASME B 16.34

Face to Face dimension ASME B 16.10 Air Test psi (g)


80

Description




Cast / Fabricated Corrosion Resistant Forged / Machined Forged / Bar (No Casting) Renewable with Valve on stream -

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bolted

ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 36")

Bonnet Gasket

Flat Ring

Compressed Non Asbestos Fibre

Body Seat Ring


UNS S32750 / 32760

Gate ( Wedge)

Solid (Note 3)

UNS S32750/ 32760

Forged/ Cast

ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 36")

Bonnet

Body

B

OS &Y

Valve Type

API 598/ BS 6755 Pt. 1

450 325

Rev

50489-530-051-SPC-1002 GATE VALVE

C15B(2" - 10"), Q15B(1/2 "- 36"), F10B (1/2" - 11/2") API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434 ( 2" - 24") API 6D/ ASME B 16.34 (26" - 36")

Testing Standard




B

Page 45 of 237




Rev

50489-530-051-SPC-1002

B

GATE VALVE C15B(2" - 10"), GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 46 of 237



Valve Type Manuf. Standard

Testing Standard

API 598/ BS 6755 Pt. 1

51379F Contractor Document Number

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

F10B API 600/ BS EN ISO 10434 (2"-24") API 6D/ ASME B 16.34 (26" - 36")

SHEET NO.

Bolted Bonnet Size Range

2" - 36"

Rating Ends



Flanged, 150#, ASME B16.5/ B 16.47 Series Effluent Water, Oily Water A, FF, Finish 125 AARH ASME B 16.34 450 325 Type of Construction




Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush UNS S32750/ 32760 Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M B Bonnet Bolted ASTM A 995 Gr 5A/ 6A Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Cast ASTM A 995 Gr 5A/ 6A GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 47 of 237



F10A(1/2" - 11/2"), Q15A(1/2" - 2") MSS-SP-80

Testing Standard

BS 5154/ MSS-SP-80

Services / Fluids

Brackish Water

Flanged, 150#, ASME B16.5 FF, Finish 125 AARH

ASME B 16.24

Face to Face dimension Manufacturer's Standard/ BS 5154

Description



Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y Screwed Bonnet 1/2" - 2" 150# Special Requirements

Valve Type

Manuf. Standard


SHEET NO.


80

Air Test psi (g)



Handwheel Cast / Fabricated Malleable Iron /Aluminium / Steel / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined To Manufacturer's standard Stem Forged / Bar (No Casting) To Manufacturer's standard Gland Packing Renewable with Valve on stream To Manufacturer's standard (Non Asbestos) Back Seat Bush ASTM B62 C83600 Bonnet Bolts / Nuts (Note 4) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Screwed ASTM B62 C83600 Bonnet Gasket Body Seat Ring Renewable / Integral ASTM B62 C83600 Gate ( Wedge) Solid (Note 3) ASTM B62 C83600 Body Cast ASTM B62 C83600 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 6. Care should be taken to avoid galvanic corrosion by dissimlar metals. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.

Page 48 of 237



C13B

Valve Type

MSS-SP-80

Testing Standard

BS 5154/ MSS-SP-80


Services / Fluids

Potable/ Fresh Water, Plant Air

SCRF, 150# to NPT(F), ASME B 1.20.1

ASME B 16.24

Face to Face dimension Manufacturer's Standard/ BS 5154

Description


51380S Contractor Document Number

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y Screwed Bonnet 1/2" - 3" 150# Special Requirements

Manuf. Standard


SHEET NO.

80

Air Test psi (g)



Handwheel Cast / Fabricated Malleable Iron /Aluminium / Steel / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined To Manufacturer's standard Stem Forged / Bar (No Casting) To Manufacturer's standard Gland Packing Renewable with Valve on stream To Manufacturer's standard (Non Asbestos) Back Seat Bush ASTM B62 C83600 Bonnet Bolts / Nuts (Note 4) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Screwed ASTM B62 C83600 Bonnet Gasket Body Seat Ring Renewable / Integral ASTM B62 C83600 Gate ( Wedge) Solid (Note 3) ASTM B62 C83600 Body Cast ASTM B62 C83600 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 6. Care should be taken to avoid galvanic corrosion by dissimlar metals. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 8. Stem Seal shall contain corrosion Inhibitor.

Page 49 of 237



Testing Standard



Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

N10C Valve Type

Manuf. Standard

SHEET NO.


8" - 16"

API 598/ BS 6755 Pt. 1

Rating Ends


Off Spec Crude Oil


ASME B 16.34





Air Test psi (g)



Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged / Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) INCONEL 625 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush INCONEL 625 Bonnet Bolts / Nuts ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable (8" - 16") INCONEL 625 Gate ( Wedge) Solid (Note 3) INCONEL 625 Body Cast ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 50 of 237

SHEET NO.


51399


14050489 N10B ( 0.5" - 20") N10C (0.5" - 6")

Piping Class

Manuf. Standard B

Testing Standard

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

Valve Type

API 602 / BS EN ISO 15761(1/2" - 1 1/2"), API 600 / BS EN ISO 10434(2"-20")



1/2" - 20"

API 598/ BS 6755 Pt. 1

Rating Ends


Off Spec Crude Oil


ASME B 16.34


B



450 325

Air Test psi (g)

80

Description



Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet Bonnet Gasket

Cast / Fabricated Corrosion Resistant Forged / Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted Flat Ring

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C INCONEL 625 Graphite with Inconel wire INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B564-UNS N06625 Compressed Non Asbestos Fibre

Body Seat Ring


INCONEL 625


Gate ( Wedge) Solid (Note 3) INCONEL 625 Body Forged ASTM B564-UNS N06625 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 51 of 237


14050489 C35B

Piping Class

Manuf. Standard

Testing Standard Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)

API 602/ BS EN ISO 15761(1/2" - 1 1/2"), API 600/ BS EN ISO 10434(2" - 16") API 598/ BS 6755 Pt. 1 Hydrocarbon Oil / Condensate, Glycol ASME B 16.34 1125 825


Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y Bolted Bonnet 1/2" - 16"

Valve Type

Size Range

300#

Rating Ends Special Requirements Flanged, 300#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B 16.10 Air Test psi (g)

80

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H

Bonnet

Bolted


Bonnet Gasket

Spiral Wound


Gate ( Wedge)

Renewable / Integral(1/2" - 1 1/2") Renewable (2" -1 6") Solid (Note 3)

Body

Forged/ Cast

Body Seat Ring

SHEET NO.


UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor. Page 52 of 237

SHEET NO.


51461



Services / Fluids


S30A


Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor


ASME B 16.34


1100 800

Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type



80

Description





Bonnet Gasket

Spiral Wound

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring SS 316 SS 316 ASTM A 351 Gr CF8M


B

Renewable Body Seat Ring Solid (Note 3) Gate ( Wedge) Cast Body GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 53 of 237

SHEET NO.


51463


14050489 S30B

Piping Class

Manuf. Standard


API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434( 2" - 16") API 598/ BS 6755 Pt. 1

Rev

50489-530-051-SPC-1002

B

Valve Type

GATE VALVE OS &Y Bolted Bonnet

Size Range

1/2" - 16"

Rating Ends




ASME B 16.34


1100 800


Air Test psi (g)


80

Description





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750 / 32760 Graphite with Inconel wire UNS S32750 / 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bonnet

Bolted


Bonnet Gasket

Spiral Wound


Body Seat Ring


UNS S32750 / 32760

Gate ( Wedge)

Solid (Note 3)

UNS S32750 / 32760

Body

Forged,Cast



B

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor. Page 54 of 237



Manuf. Standard

Testing Standard



Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

Q35A Valve Type

API 600/ BS EN ISO 10434 (3" -24"), API 6D/ASME B 16.34 (26" - 32") BS 5154/ MSS-SP-80

Size Range

3" - 32"

Rating Ends


Brackish Water

Flanged, 300#, ASME B16.5 / B 16. 47 A, RF, Finish 125 AARH

ASME B 16.24



Bolted Bonnet

Air Test psi (g)




Page 55 of 237




F30A API 600/ BS EN ISO 10434 BS 5154/ MSS-SP-80

Size Range Rating Ends Flanged, 300#, ASME B16.5, FF, Finish 125 AARH

ASME B 16.24



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B


Valve Type

Brackish Water

775 575

SHEET NO.




Page 56 of 237

SHEET NO.


51479



Manuf. Standard

Testing Standard


B

OS &Y

Valve Type


1/2" - 24"

Rating Ends


Hydrocarbon Oil / Gas / Condensate, Oily Water, Glycol


ASME B 16.34


80

Description





Bonnet

Bolted

Bonnet Gasket

Gate ( Wedge)

Flat Ring Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 24") Solid (Note 3)

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24") Compressed Non Asbestos Fibre

Body

Forged,Cast

Body Seat Ring

Rev

50489-530-051-SPC-1002 GATE VALVE

C35B(2" - 14 "), S30B(1/2"-11/2"), Q35B(2" - 24"), F30B(1/2" - 11/2") API 602/ BS EN ISO 15761 (1/2"-1 1/2"), API 600/ BS EN ISO 10434(2"-24") API 598/ BS 6755 Pt. 1

1125 825



B

UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24")




SHEET NO. 51479F Contractor Document Number

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

F30B Valve Type

Bolted Bonnet

, API 600 / BS EN ISO 10434

Size Range

2" - 24"

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends


Services / Fluids

Hydrocarbon Oil / Gas / Condensate, Oily Water, Glycol


ASME B 16.34


Manuf. Standard




Air Test psi (g)



Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush UNS S32750/ 32760 B Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolted ASTM A 995 Gr 5A/ 6A Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring UNS S32750/ 32760 Renewable Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Cast ASTM A 995 Gr 5A/ 6A GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 58 of 237



Q35A API 600/ BS EN ISO 10434

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids

Brackish Water


ASME B 16.34


Description



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y Bolted Bonnet 2" 300# Special Requirements

Valve Type

Manuf. Standard


SHEET NO.



Ductile Iron/ Malleable Iron / Cast Steel Handwheel Cast / Fabricated Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) UNS S32750/ 32760 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush UNS S32750/ 32760 B Bonnet Bolts / Nuts ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolted ASTM A 995 Gr 5A/ 6A Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Body Seat Ring Renewable UNS S32750/ 32760 Gate ( Wedge) Solid (Note 3) UNS S32750/ 32760 Body Cast ASTM A 995 Gr 5A/ 6A GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 59 of 237



Testing Standard


Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

N30C Valve Type

Manuf. Standard

SHEET NO.



8" - 16"

API 598/ BS 6755 Pt. 1

Rating Ends


Off Spec Crude Oil


ASME B 16.34





Air Test psi (g)



Handwheel Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Name Plate Corrosion Resistant SS/ Ni Alloy Stem Sleeve/ Nut Forged/ Machined ASTM A 439 Type D-2 / D-2C Stem Forged / Bar (No Casting) INCONEL 625 Gland Packing Renewable with Valve on stream Graphite with Inconel wire Back Seat Bush INCONEL 625 Bonnet Bolts / Nuts ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolted ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined Bonnet Gasket Flat Ring Compressed Non Asbestos Fibre Renewable Body Seat Ring INCONEL 625 Gate ( Wedge) Solid (Note 3) INCONEL 625 Body Cast ASTM A 216 Gr WCB + 3MM INCONEL 625 Lined GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 60 of 237

SHEET NO.


51499



Manuf. Standard

Testing Standard

N30B (0.5" - 16") N30C (0.5" - 6" API 602/ BS EN ISO 15761 (1/2" - 1 1/2"), API 600/ BS EN ISO 10434 B (2"-16")


Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

Valve Type


1/2" - 16"

API 598/ BS 6755 Pt. 1

Rating Ends


Off Spec Crude Oil


ASME B 16.34


B



1125 825

Air Test psi (g)

80

Description



Handwheel Name Plate Stem Sleeve/ Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet Bonnet Gasket

Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with Valve on stream Bolted Flat Ring Renewable / Integral(1/2" - 1 1/2") Renewable (2" - 6") Solid (Note 3) Forged

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C INCONEL 625 Graphite with Inconel wire INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B564-UNS N06625 Compressed Non Asbestos Fibre

Body Seat Ring


INCONEL 625

Gate ( Wedge) INCONEL 625 Body ASTM B564-UNS N06625 GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 61 of 237


14050489

Manuf. Standard


Valve Type

API 602/ BS EN ISO 15761(1/2" - 1 1/2"), API 600/ BS EN ISO 10434 (2" - 24") API 598/ BS 6755 Pt. 1 Hydrocarbon Gas/ Oil/ Condensate, Glycol ASME B 16.34 2225 1650


Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

C65B

Piping Class

SHEET NO.


1/2" - 24"

Rating 600# Ends Special Requirements Flanged, 600#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B 16.10 Air Test psi (g)

80

Description





Bonnet

Bolted

Bonnet Gasket

Spiral Wound

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 24") SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring

Body Seat Ring


Gate ( Wedge)

Solid (Note 3)

Body

Forged/ Cast


UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 24")

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 6. Stem Seal shall contain corrosion Inhibitor. Page 62 of 237

SHEET NO.


51561



Services / Fluids


S60A


Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution


ASME B 16.34


2175 1600

Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type



80

Description






B

Bonnet Gasket

Spiral Wound

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring SS 316 SS 316 ASTM A 351 Gr CF8M

Body Seat Ring Renewable Gate ( Wedge) Solid (Note 3) Body Cast GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Wedge type shall be as per Clause 7.7 of KOC Standard, KOC-MP-013. 4. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-013. 5. Stem Seal shall contain corrosion Inhibitor.

Page 63 of 237

SHEET NO.


51579


14050489

Rev

50489-530-051-SPC-1002

B

GATE VALVE OS &Y

C65B

Piping Class


Valve Type

API 602/ BS EN ISO 15761(1/2" - 1 1/2"), API 600/ BS EN ISO 10434 (2" - 24")

Size Range

1/2" - 24"

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends


Services / Fluids



ASME B 16.34


Manuf. Standard


2225 1650

Bolted Bonnet

Air Test psi (g)


80

Description





Bonnet

Bolted

Bonnet Gasket

Spiral Wound

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2" - 24") SS 316 Windings, Flexible Graphite Filled, CS outer Ring and SS 316 Inner Ring

Body Seat Ring


Gate ( Wedge)

Solid (Note 3)

Body

Forged/ Cast


B



SHEET NO.


51779


14050489


Rev

50489-530-051-SPC-1002

B

GATE VALVE Piping Class

Q95B OS &Y

Valve Type

Manuf. Standard

Testing Standard

API 602/ BS EN ISO 15761 (1/2"-1 1/2"), API 600/ BS EN ISO 10434(2") API 598/ BS 6755 Pt. 1

Size Range

1/2" - 2"

Rating Ends


Effluent Water, Treated Water

Flanged, 1500#, ASME B16.5, RTJ, Finish 32 AARH

ASME B 16.34


Bolted Bonnet


Services / Fluids Pressure Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)

5625 4125

Air Test psi (g)

80

Description





Bonnet

Bolted

Bonnet Gasket

Gate ( Wedge)

Ring Type Renewable / Integral(1/2" - 1 1/2") Renewable (2" ) Solid (Note 3)

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2") Super Duplex Oval Shape Gasket

Body

Forged, Cast

Body Seat Ring


B

UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 11/2")/ ASTM A 995 Gr 5A/ 6A (2")


SHEET NO.


52001




C13A



SW, 3000# to ASME B16.11

ASME B 16.34

Face to Face dimension Manufacturer's Std. Air Test psi (g)


Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts Bolted Bonnet Bonnet Gasket

Spiral Wound

Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements

Valve Type


2975 2175




Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105 Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring

Renewable / Integral 13% Cr. Steel + Stellite Facing Seat Ring Loose (Spherical/ Ball/ Plug) ASTM A 105 + Stellite Facing Disc Forged ASTM A 105 Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.

Page 66 of 237

SHEET NO.


52061



Services / Fluids


S10A, S30A, S60A



SW, 3000 # to ASME B16.11

ASME B 16.34

Face to Face dimension Manufacturer's Std.

2900 2125

Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type



80

Description



Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet

Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream Bolted

Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 F 316/ 316L Dual Stamped

Bonnet Gasket

Spiral Wound

Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring


B

Renewable / Integral ASTM A 182 F 316/ 316L Dual Stamped Seat Ring Loose (Spherical/ Ball/ Plug) ASTM A 182 F 316/ 316L Dual Stamped Disc Forged ASTM A 182 F 316/ 316L Dual Stamped Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.

Page 67 of 237




Q35A, F30A


Brackish Water

SW, 3000 # to ASME B16.11

ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B


Valve Type


3000 2200

SHEET NO.



Cast / Fabricated Malleable Iron / Ductile Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate Yoke Bush / Retaining Nut Forged/ Machined ASTM A439 Type D-2 / D-2C Forged / Bar (No Casting) Stem UNS S32750/ 32760 Renewable with valve on stream Gland Packing Graphite with Inconel Wire Back Seat Bush UNS S32750/ 32760 B ASTM A 193 Gr B8M ASTM A 194 Gr 8M Bonnet Bolts / Nuts Bolted Bonnet ASTM A 182 Gr F 53 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable / Integral Seat Ring UNS S32750/ 32760 Loose (Spherical/ Ball/ Plug) Disc UNS S32750/ 32760 Forged Body ASTM A 182 Gr F 53 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.

Page 68 of 237

SHEET NO.


52301



C13A BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids



ASME B 16.34


450 325


Air Test psi (g)

Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements

Valve Type

Manuf. Standard



80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream (Note 3) Bolted

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C 13% Cr. Steel Graphite with Inconel Wire 13% Cr. Steel ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 216 Gr WCB

Bonnet Gasket

Spiral Wound


Seat Ring

Renewable

Disc

Loose (Spherical/ Ball/ Plug)


13% Cr. Steel (2" - 6") ASTM A105 + 13% Cr. Steel Deposit (8" - 16") 13% Cr. Steel/ ASTM A 216 Gr WCB + 13% Cr. Steel Deposit ASTM A 216 Gr WCB

Cast Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.

Page 69 of 237


14050489

Valve Type API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 16")

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids



Manuf. Standard

Pressure -Temperature Rating

Description

450 325


Rev

50489-530-051-SPC-1002

B

Bolted Bonnet 1/2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

Face to Face dimension

ASME B 16.34

Hydro Test Pressure Body psi (g) Seat psi (g)

52311

GLOBE VALVE OS &Y

C15B

Piping Class

SHEET NO.

ASME B 16.10 Air Test psi (g)


Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts



Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S 32750 / 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")

Bonnet

Bolted

Bonnet Gasket

Spiral Wound


Seat Ring

Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above)

UNS S32750/ 32760

Disc


UNS S32750/ 32760

Body

Forged (1/2" - 1 1/2") / Cast (2" & Above)

ASTM A 105N (1/2" - 1 1/2")/ ASTM A 216 Gr WCB (2" - 16")

Page 70 of 237




Rev

50489-530-051-SPC-1002

B

GLOBE VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor.

Page 71 of 237


14050489

Valve Type API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 16")

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids

Hydrocarbon Gas/ Oil/ Condensate


Manuf. Standard


Description

450 325


Rev

50489-530-051-SPC-1002

B

Bolted Bonnet 1/2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This Valve Data Sheet shall be applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) services only.


ASME B 16.34


52312

GLOBE VALVE OS &Y

C15B

Piping Class

SHEET NO.



Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts



Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316L Graphite with Inconel Wire SS 316L ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 16")

Bonnet

Bolted

Bonnet Gasket

Spiral Wound


Seat Ring


SS 316L

Disc


SS 316L

Body

Forged (1/2" - 1 1/2") / Cast (2" & Above)

ASTM A 105N (1/2" - 1 1/2")/ ASTM A 216 Gr WCB (2" - 16")

Page 72 of 237




Rev

50489-530-051-SPC-1002

B


Page 73 of 237

SHEET NO.


52361



S10A BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids



ASME B 16.34


425 325


Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard



80

Description





Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M

Bonnet Gasket

Spiral Wound



B

Renewable SS 316 Seat Ring Loose (Spherical/ Ball/ Plug) SS 316 Disc Cast ASTM A 351 Gr CF8M Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.

Page 74 of 237


14050489

Valve Type

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids

Hydrocarbon Gas/Condensate, Glycol



425 325



80



Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts

Cast / Fabricated Corrosion Resistant

Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy

Forged/ Machined

ASTM A 439 Type D-2/ D-2C

Forged / Bar (No Casting) Renewable with valve on stream -

UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 GR F 316/316L Dual Stamped (1/2" 1 1/2") / ASTM A 351 Gr CF8M (2" - 12") Spiral-Wound, SS316 Windings, Flexible Graphite Fillled, CS Outer Ring & SS 316 Inner Ring

Bolted

Bonnet Gasket

Spiral Wound

Seat Ring Disc Body

B

1/2" - 12"

Description

Bonnet

Rev

50489-530-051-SPC-1002


ASME B 16.34



Bolted Bonnet

API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')

Manuf. Standard

52363

GLOBE VALVE OS &Y

S10B

Piping Class

SHEET NO.

Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above) Loose (Spherical/ Ball/ Plug) Forged (1/2" - 1 1/2") / Cast (2" - 12")


B

UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 GR F 316/316L Dual Stamped (1/2" 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")

GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor. Page 75 of 237

SHEET NO.


52364


14050489

Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y

S10B

Piping Class


Valve Type

Bolted Bonnet

API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')

Size Range

1/2" - 12"

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends


Services / Fluids

Hydrocarbon Gas/Condensate


Manuf. Standard




ASME B 16.34


425 325

2. This Valve Data Sheet shall be applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) services only.


80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream -

Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bonnet

Bolted

ASTM A 182 GR F 316/316L Dual Stamped (1/2" - 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")

Bonnet Gasket

Spiral Wound


Seat Ring Disc Body

Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above) Loose (Spherical/ Ball/ Plug) Forged (1/2" - 1 1/2") / Cast (2" - 12")


B

SS 316L SS 316L ASTM A 182 GR F 316/316L Dual Stamped (1/2" - 1 1/2") / ASTM A 351 Gr CF8M (2" - 12")




Q15A BS 1873

Testing Standard

BS 5154/ MSS-SP-80

Services / Fluids

Brackish Water


ASME B 16.24

Face to Face dimension BS 5154 / ASME B 16.10

Description



Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard


SHEET NO.


80

Air Test psi (g)



Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate ASTM A 439 Type D-2/ D-2C Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Monel / NI-AL-Bronze Stem Renewable with valve open on stream Gland Packing Graphite with Inconel wire Forged /Machined Monel/ NI-AL-Bronze Back Seat Bush (Note 3) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bolted Bonnet ASTM B 148 UNS C95800 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable Seat Ring Monel/ NI-AL-Bronze Loose (Spherical/ Ball/ Plug) Disc Monel/ NI-AL-Bronze Cast Body ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.

Page 77 of 237

SHEET NO.


52378F



C13B (4" - 12"), F10A ( 2" - 16") BS 1873

Testing Standard

BS 5154/ MSS-SP-80


Services / Fluids

Brackish Water, Potable/ Fresh Water, Plant Air


ASME B 16.24


Description

300 225

Air Test psi (g)

Type of Construction Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve open on stream Forged /Machined (Note 3) Bolted Flat Ring Renewable Loose (Spherical/ Ball/ Plug) Cast (Straight Pattern)

Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard





Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C Monel / NI-AL-Bronze Graphite with Inconel wire Monel/ NI-AL-Bronze (Note 8) ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B 148 UNS C95800 Compressed Non-Asbetos Fibre Monel/ NI-AL-Bronze (Note 8) Monel/ NI-AL-Bronze (Note 8) ASTM B 148 UNS C95800

Handwheel Name Plate Yoke Bush / Retaining Nut Stem Gland Packing Back Seat Bush Bonnet Bolts / Nuts Bonnet Bonnet Gasket Seat Ring Disc Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor. 8. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .

Page 78 of 237



C15B ( 1/2" - 12"), F10B (1/2" - 11/2"), Q15B (1/2" - 16")

API 598/ BS 6755 Pt. 1

Rating Ends

Hydrocarbon Oil/ Condensate, Oily Water, Glycol, Effluent Water


Size Range

1/2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.


80

Description




Cast / Fabricated Corrosion Resistant Forged / Bar (No Casting) Renewable with valve on stream -

Bonnet

Bolted

Bonnet Gasket

Flat Ring Renewable / Integral (1/2" - 1 1/2") Renewable (2" & Above) Loose (Spherical/ Ball/ Plug) Forged (1/2" - 11/2") / Cast (2" - 16")

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S 32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 11/2") ASTM A 995 Gr 5A/ 6A (2" - 16") Compressed Non-Asbetos Fibre

Seat Ring Disc Body

B


ASME B 16.34

450 325

Rev

50489-530-051-SPC-1002

OS &Y

Testing Standard



Bolted Bonnet

API 602 / BS EN ISO 15761(1/2" - 1 1/2") BS 1873 (2" - 16")


52379

GLOBE VALVE Valve Type

Manuf. Standard

Services / Fluids

SHEET NO.


B




14050489 F10B

Piping Class

BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids

Effluent Water, Oily Water


ASME B 16.34


Description

450 325


Air Test psi (g)


Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush Bonnet Bolts / Nuts


Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y Bolted Bonnet 2" - 16" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

Valve Type

Manuf. Standard


SHEET NO.

80 Material of Construction Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S 32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bonnet

Bolted

ASTM A 995 Gr 5A/ 6A

Bonnet Gasket Seat Ring Disc

Flat Ring Renewable Loose (Spherical/ Ball/ Plug)

Compressed Non-Asbetos Fibre UNS S32750/ 32760 UNS S32750/ 32760

Body

Cast



B

GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.

Page 80 of 237

SHEET NO.


52380S



C13B MSS-SP-80

Testing Standard

BS 5154/ MSS-SP-80


Services / Fluids


SCRF, 3000# to NPT, ASME B 1.20.1

ASME B 16.24

Face to Face dimension Manufacturer's Std./ BS 5154

Description

350 250

Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y Screwed Bonnet 1/2" - 3" 150# Special Requirements

Valve Type

Manuf. Standard



80

Air Test psi (g)




Malleable Iron /Aluminium / Steel / Cast Steel SS/ Ni Alloy To Manufacturer's standard To Manufacturer's standard To Manufacturer's standard ASTM B62 UNS C83600 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B62 UNS C83600 ASTM B62 UNS C83600 ASTM B62 UNS C83600 ASTM B62 UNS C83600


Handwheel Name Plate Yoke Bush / Retaining Nut Nickel or Copper Alloy Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts Bonnet Cast / Screwed Bonnet Gasket Renewable / Integral Seat Ring Loose (Spherical/ Ball/ Plug) Disc Cast Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.

Page 81 of 237

SHEET NO.


52380F



F10A (1/2" - 11/2"), Q15A (1/2" - 2") MSS-SP-80

Testing Standard

BS 5154/ MSS-SP-80


Services / Fluids



ASME B 16.24

Face to Face dimension Manufacturer's Std./ BS 5154

Description

350 250

Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y Screwed Bonnet 1/2" - 2" 150# Special Requirements

Valve Type

Manuf. Standard



80

Air Test psi (g)




Malleable Iron /Aluminium / Steel / Cast Steel SS/ Ni Alloy To Manufacturer's standard To Manufacturer's standard To Manufacturer's standard ASTM B62 UNS C83600 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM B62 UNS C83600 Compressed Non-Asbetos Fibre ASTM B62 UNS C83600 ASTM B62 UNS C83600 ASTM B62 UNS C83600


Handwheel Name Plate Yoke Bush / Retaining Nut Nickel or Copper Alloy Stem Renewable with valve on stream Gland Packing Back Seat Bush (Note 3) Bonnet Bolts / Nuts Bonnet Cast / Screwed Bonnet Gasket Flat Ring Renewable / Integral Seat Ring Loose (Spherical/ Ball/ Plug) Disc Cast Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.

Page 82 of 237




Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y

N10B (0.5" - 16") N10C (0.5" - 6") Valve Type

Manuf. Standard

API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 16") B


1/2" - 16"

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids

Off Spec Crude Oil



ASME B 16.34


B





Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate Yoke Bush/ Retaining Nut ASTM A 439 Type D-2 / D-2C Forged / Bar (No Casting) Stem INCONEL 625 Renewable with Valve on stream Gland Packing Graphite with Inconel wire Back Seat Bush INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bonnet Bolted ASTM B564-UNS N06625 Bonnet Gasket Flat Ring Compressed Non-Asbetos Fibre Renewable / Integral Body Seat Ring INCONEL 625 Loose (Spherical/ Ball/ Plug) Disc INCONEL 625 Forged ASTM B 564-UNS N06625 Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.

Page 83 of 237


14050489

Valve Type API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873(2" - 12")

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids

Hydrocarbon Oil/ Condensate, Glycol


Manuf. Standard


1125 825


Rev

50489-530-051-SPC-1002

B

Bolted Bonnet 1/2" - 12" 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.


ASME B 16.34


52411

GLOBE VALVE OS &Y

C35B

Piping Class

SHEET NO.


80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream (Note 4)

Bonnet

Bolted

Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S32750 / 32760 Graphite with Inconel Wire UNS S32750 / 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 12")

Bonnet Gasket

Spiral Wound


Seat Ring


UNS S32750 / 32760

Disc


UNS S32750 / 32760

Body

Forged (1/2" - 1 1/2") / Cast (2" - 12")



Page 84 of 237




Rev

50489-530-051-SPC-1002

B


Page 85 of 237

SHEET NO.


52461



S30A BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids



ASME B 16.34


1100 800


Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard



80

Description






Malleable Iron / Ductile Iron /Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M

B

Bonnet Gasket

Spiral Wound



Page 86 of 237



Rev

50489-530-051-SPC-1002

B


14050489

GLOBE VALVE OS &Y

S30B

Piping Class

Valve Type

Bolted Bonnet

API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids

Hydrocarbon Gas/Condensate, Glycol


Manuf. Standard

SHEET NO.


1100 800



ASME B 16.34


1/2" - 12"


80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream -

Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S32750/ 32760 Graphite with Inconel wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M

Bonnet

Bolted


Bonnet Gasket

Spiral Wound


Seat Ring


UNS S32750/ 32760

Disc


UNS S32750/ 32760

Body

Forged (1/2" - 1 1/2") / Cast (2" - 12")



B




Q35A BS 1873

Testing Standard

BS 5154/ MSS-SP-80

Services / Fluids

Brackish Water


ASME B 16.24


Description



Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard


SHEET NO.


80

Air Test psi (g)



Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate ASTM A 439 Type D-2/ D-2C Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Monel/ Ni-Al-Bronze Stem Renewable with valve open on stream Gland Packing Graphite with Inconel wire Forged /Machined Monel/ Ni-Al-Bronze Back Seat Bush (Note 3) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bolted Bonnet ASTM B 148 UNS C95800 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable Monel/ Ni-Al-Bronze Seat Ring Loose (Spherical/ Ball/ Plug) Monel/ Ni-Al-Bronze Disc Cast Body ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.

Page 88 of 237



F30A BS 1873

Testing Standard

BS 5154/ MSS-SP-80

Services / Fluids

Brackish Water


ASME B 16.24


Description



Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard


SHEET NO.


80

Air Test psi (g)



Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate ASTM A 439 Type D-2/ D-2C Yoke Bush / Retaining Nut Forged/ Machined Forged / Bar (No Casting) Monel/ Ni-Al-Bronze Stem Renewable with valve open on stream Gland Packing Graphite with Inconel wire Forged /Machined Monel/ Ni-Al-Bronze Back Seat Bush (Note 3) ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bolted Bonnet ASTM B 148 UNS C95800 Flat Ring Bonnet Gasket Compressed Non-Asbetos Fibre Renewable Monel/ Ni-Al-Bronze Seat Ring Loose (Spherical/ Ball/ Plug) Monel/ Ni-Al-Bronze Disc Cast Body ASTM B 148 UNS C95800 GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Any Bronze Alloy used in cold-worked condition shall be capable of passing the 'Mercurous Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 5. Care should be taken to avoid galvanic corrosion by dissimilar metals. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 7. Stem seal shall contain Corrosion Inhibitor.

Page 89 of 237



Rev

50489-530-051-SPC-1002

B

GLOBE VALVE

C35B ( 1/2" - 10"), F30B ( 1/2" - 11/2"), Q35B ( 1/2" - 12")

Piping Class

OS &Y

Valve Type

Bolted Bonnet

API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 12")

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids

Hydrocarbon Oil/ Condensate, Oily Water, Glycol, Effluent Water



1125 825



ASME B 16.34



80

Description





Bonnet

Bolted


Flat Ring Renewable Loose (Spherical/ Ball/ Plug) Forged (1/2" - 1 1/2") / Cast (2" - 12")

Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750 / 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 182 Gr F 53 (1/2" - 12") ASTM A 995 Gr 5A/ 6A (2" - 12") Compressed Non-Asbetos Fibre UNS S32750/ 32760 UNS S32750/ 32760 ASTM A 182 Gr F 53 (1/2" - 12")/ ASTM A 995 Gr 5A/ 6A (2" - 12")

Body

52479


14050489

Manuf. Standard

SHEET NO.


B


Page 90 of 237


14050489


Rev

50489-530-051-SPC-1002

B

GLOBE VALVE Piping Class

F30B

Manuf. Standard

BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids


OS &Y

Valve Type

Bolted Bonnet 2" - 12" 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

Size Range Rating Ends Flanged, 300#, ASME B16.5, FF, Finish 125 AARH Face to Face dimension


ASME B 16.34


1125 825


80

Description






Ductile Iron/ Malleable Iron / Cast Steel SS/ Ni Alloy ASTM A439 Type D-2 / D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B8M ASTM A 194 Gr 8M

B

Bonnet

Bolted





Body

Cast



Page 91 of 237

SHEET NO.


52482

KOC Contract No 14050489 Q35A

Piping Class

Rev

50489-530-051-SPC-1002

B

GLOBE VALVE OS &Y Bolted Bonnet 2" 300# Special Requirements

Valve Type

Manuf. Standard

BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids

Brackish Water


ASME B 16.34



Contractor Document Number VALVE MATERIAL SPECIFICATION

1125 825


Air Test psi (g)




Cast / Fabricated Handwheel Corrosion Resistant Name Plate Yoke Bush / Retaining Nut Forged / Bar (No Casting) Stem Renewable with valve on stream Gland Packing Back Seat Bush Bonnet Bolts / Nuts


B

Bonnet

Forged/ Cast, Bolted





Body

Cast



Page 92 of 237



Manuf. Standard

N30B (0.5" - 12') N30C (0.5" - 6") API 602 / BS EN ISO 15761 (1/2" - 1 1/2") BS 1873 (2" - 12") B

Valve Type

Size Range

Rev

50489-530-051-SPC-1002

B

1/2" - 12"

Rating Ends

Services / Fluids

Oily Water


Description


Bolted Bonnet

API 598/ BS 6755 Pt. 1


52499

GLOBE VALVE OS &Y

Testing Standard


SHEET NO.

B







Cast / Fabricated Ductile Iron/ Malleable Iron / Cast Steel Handwheel Corrosion Resistant SS/ Ni Alloy Name Plate Yoke Bush/ Retaining Nut ASTM A 439 Type D-2 / D-2C Forged / Bar (No Casting) Stem INCONEL 625 Renewable with Valve on stream Gland Packing Graphite with Inconel wire Back Seat Bush INCONEL 625 ASTM A 193 Gr B7 ASTM A 194 Gr 2H Bonnet Bolts / Nuts Bonnet Bolted ASTM B564-UNS N06625 Flat Ring Compressed Non-Asbetos Fibre Bonnet Gasket Renewable Body Seat Ring INCONEL 625 Loose (Spherical/ Ball/ Plug) Disc INCONEL 625 Forged ASTM B564-UNS N06625 Body GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Bonnet Test Point requirement and Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 4. Stem seal shall contain Corrosion Inhibitor.

Page 93 of 237


14050489

Valve Type

Size Range

Testing Standard

API 598/ BS 6755 Pt. 1

Rating Ends

Services / Fluids




2225 1650

Rev

50489-530-051-SPC-1002

B



ASME B 16.34



Bolted Bonnet

API 602 / BS EN ISO 15761 (1/2" - 11/2") BS 1873 (2" - 12')

Manuf. Standard

52511

GLOBE VALVE OS &Y

C65B

Piping Class

SHEET NO.


80

Description




Cast / Fabricated Corrosion Resistant Forged/ Machined Forged / Bar (No Casting) Renewable with valve on stream (Note 3)

Bonnet

Bolted

Malleable Iron / Ductile Iron / Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C UNS S32750/ 32760 Graphite with Inconel Wire UNS S32750/ 32760 ASTM A 193 Gr B7 ASTM A 194 Gr 2H ASTM A 105N (1/2" - 1 1/2") ASTM A 216 Gr WCB (2" - 12")

Bonnet Gasket

Spiral Wound


Seat Ring


UNS S32750/ 32760

Disc


UNS S32750/ 32760

Body

Forged (1/2" - 1 1/2") / Cast (2" - 12")



GENERAL NOTES : 1. This valve material sheet shall be read in conjunction with technical notes of Valve Material Specification. 2. This valve data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy-Steel Fastners(Bolts/Nuts) shall be electro-zinc plated in accordance with ASTM B 633. 4. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-014. 5. Stem seal shall contain Corrosion Inhibitor. Page 94 of 237

SHEET NO.


52561



S60A BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids



ASME B 16.34


2175 1600


Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard



80

Description





Malleable Iron / Ductile Iron /Cast Steel SS/ Ni Alloy ASTM A 439 Type D-2/ D-2C SS 316/ 316L Dual Stamped Graphite with Inconel wire SS 316/ 316L Dual Stamped ASTM A 193 Gr B8M ASTM A 194 Gr 8M ASTM A 351 Gr CF8M

Bonnet Gasket

Spiral Wound



B


Page 95 of 237


14050489 C65B

Piping Class

BS 1873

Testing Standard

API 598/ BS 6755 Pt. 1


Services / Fluids

Hydrocarbon Gas/Oil/ Condensate, Oily Water


2225 1650


Rev

50489-530-051-SPC-1002

B


ASME B 16.34


52579

GLOBE VALVE OS &Y Bolted Bonnet 2" - 6" 600# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

Valve Type

Manuf. Standard


SHEET NO.


80

Description






Bonnet

Bolted


Bonnet Gasket

Spiral Wound


Seat Ring Disc

Renewable Loose (Spherical/ Ball/ Plug)

UNS S32750/ 32760 UNS S32750/ 32760

Body

Cast



B


Page 96 of 237

SHEET NO.


53001




C13A API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1

Size Range Rating Ends SW, 3000# to ASME B16.11

ASME B 16.34

Face to Face dimension Manufacturer's Standard. Air Test psi (g)

Rev

50489-530-051-SPC-1002

B

CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 1 1/2" 800# Special Requirements

Valve Type

Fuel Oil(Diesel), Inert Gas

2975 2175


80

Description



Body Piston Seat Ring Spring Cover Guide

Forged Lift Type Renewable / Integral Bolted Forged / Bar

Cover Gasket

Spiral Wound

ASTM A105 ASTM A105 + Stellite facing 13% Cr. Steel + Stellite facing Inconel X-750 ASTM A105 13% Cr. Steel SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy


(Note 5) Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 97 of 237

SHEET NO.


53061



Services / Fluids


S10A,S30A, S60A API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1


SW, 3000 # to ASME B16.11

ASME B 16.34


Rev

50489-530-051-SPC-1002

B


Valve Type

Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution,Scale Inhibitor

2900 2125


80

Description





Cover gasket

Spiral Wound

ASTM A 182 F 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped Inconel X-750 ASTM A 182 F 316/ 316L Dual Stamped SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy


Cover Bolts / Nuts B Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 98 of 237

SHEET NO.


53061Z



S30A, S60A BS 1868

Testing Standard

API 598/ BS 6755 Part-1

Services / Fluids


SW, 3000 # to ASME B16.11

ASME B 16.34

Face to Face dimension Manufacturer's Standard.

2900 2125


Air Test psi (g)

B

80

Description



Body Seat Ring Disc Cover Hinge Hinge Pin

Forged Renewable / Integral Bolted

Cover gasket

Spiral Wound

ASTM A 182 F 316/ 316L Dual Stamped 316/ 316L Dual Stamped 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped ASTM A 182 F 316/ 316L Dual Stamped SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy

Forged / Bar

Rev

50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 1/2" - 11/2" 800# Special Requirements

Valve Type

Manuf. Standard





Page 99 of 237

SHEET NO.


53082




Q35A, F30A


Brackish Water

SW, 3000 # to ASME B16.11

ASME B 16.34


Rev

50489-530-051-SPC-1002

B


Valve Type

API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1

3000 2200


80



Forged Lift Type Renewable / Integral Bolted Forged / Bar Flat Ring Corrosion Resistant

ASTM A 182 Gr F 53 ASTM A 182 Gr F 53 ASTM A 182 Gr F 53 Inconel X-750 ASTM A 182 Gr F 53 UNS S32750/ 32760 Compressed Non Asbestos Fibre ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy


Body Piston Seat Ring Spring Cover Guide Cover gasket Cover Bolts / Nuts B Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 100 of 237

SHEET NO.


53301


14050489 C13A

Piping Class

BS 1868

Testing Standard

API 598 / BS 6755 Part-1


Services / Fluids

Fuel Oil(Diesel), Inert Gas

Flanged, 150 #, ASME B16.5, RF, Finish - 125 AARH

ASME B 16.34


450 325

Air Test psi (g)


Material of Construction ASTM A 216 Gr WCB 13% Cr. Steel (2" - 6") ASTM A105 + 13% Cr. Steel Deposit (8" - 16")

Body Seat Ring

Renewable

Disc

-

Cover Hinge Hinge Pin

Bolted

Cover Gasket

Spiral Wound

Forged / Bar

B

80

Description

Cast

Rev

50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 2" -16" 150# Special Requirements

Valve Type

Manuf. Standard




13% Cr. Steel/ ASTM A 216 WCB + 13% Cr. Steel Deposit ASTM A 216 Gr WCB ASTM A 216 Gr WCB 13% Cr. Steel SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy


Page 101 of 237

SHEET NO.


53311P



C15B


Rev

50489-530-051-SPC-1002

B


Valve Type




Flanged, 150 #,ASME B16.5, RF, Finish - 125 AARH

ASME B 16.34




450 325

Air Test psi (g)

80

Description



Body Seat Ring Spring Piston Cover Hinge Pin / Guide

Forged Renewable / Integral Bolted Forged / Bar

Cover gasket

Spiral Wound

ASTM A105N UNS S32750/ 32760 Inconel X-750 UNS S32750/ 32760 ASTM 105N UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy



Page 102 of 237

SHEET NO.


53311


14050489 C15B

Piping Class Manuf. Standard Testing Standard

Services / Fluids

B

Valve Type

BS 1868 (2" - 24") API 6D (26" -48") API 598/ BS 6755 Part-1 Hydrocarbon Gas/ Oil/ Condensate, Glycol


ASME B 16.34 450 325


B

B

Flanged, 150#, ASME B16.5 / B 16.47 Series A, RF, Finish 125 AARH

Rev

50489-530-051-SPC-1002

B

CHECK VALVE Swing check Bolted cover 2" - 48" 150# Special Requirements



80

Description



Body

Cast

ASTM A 216 Gr WCB

Seat Ring

Renewable

UNS S 32750 / 32760

Disc Cover Hinge Hinge Pin / Guide

Bolted

Cover gasket

Spiral Wound

UNS S 32750 / 32760 ASTM A 216 Gr WCB ASTM A 216 Gr WCB UNS S 32750 / 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy

Forged / Bars




Page 103 of 237

SHEET NO.


53312P




C15B


Hydrocarbon Oil/ Condensate


ASME B 16.34


Rev

50489-530-051-SPC-1002

B


Valve Type


450 325



80

Description




Forged Renewable/ Integral Bolted Forged / Bar

Cover gasket

Spiral Wound

ASTM A105N SS316L Inconel X-750 SS316L ASTM 105N SS316L SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy



Page 104 of 237

SHEET NO.


53312


14050489 C15B


Services / Fluids

B

Valve Type

BS 1868 (2" - 24") API 6D (26" -48") API 598/ BS 6755 Part-1 Hydrocarbon Oil/ Condensate


ASME B 16.34 450 325

B


B


Rev

50489-530-051-SPC-1002

B



Face to Face dimension ASME B 16.10 80

Air Test psi (g)

Description



Body

Cast

ASTM A 216 Gr WCB

Seat Ring

Renewable

SS316L


Bolted

Cover gasket

Spiral Wound

SS316L ASTM A 216 Gr WCB ASTM A 216 Gr WCB SS316L SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy

Forged / Bars




Page 105 of 237

SHEET NO.


53361



S10A BS 1868

Testing Standard

API 598/ BS 6755 Part-1

Services / Fluids



ASME B 16.34


425 325


Air Test psi (g)

B

80

Description




Cast Renewable Bolted

Cover gasket

Spiral Wound

ASTM A 351 Gr CF8M SS 316 SS 316 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy

Forged / Bar

Rev

50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 2" - 12" 150# Special Requirements

Valve Type

Manuf. Standard




B

Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 106 of 237

SHEET NO.


53363P



S10B API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1


Rev

50489-530-051-SPC-1002

B


Valve Type Size Range Rating Ends

1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be

complied. Services / Fluids


Hydrocarbon Gas/ Condensate ,Glycol


ASME B 16.34


425 325

Air Test psi (g)

80

Description





Cover gasket

Spiral Wound

ASTM A 182 F 316/ 316L Dual Stamped UNS S 32750/ 32760 UNS S 32750/ 32760 Inconel X-750 ASTM A 182 F 316/ 316L Dual Stamped UNS S 32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy


Cover Bolts / Nuts Corrosion Resistant Name Plate B General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 107 of 237

SHEET NO.


53363



S10B

Manuf. Standard

BS 1868

Testing Standard

API 598/ BS 6755 Part-1


Rev

50489-530-051-SPC-1002

B








ASME B 16.34


425 325

Air Test psi (g)

80

Description





Cover gasket

Spiral Wound

ASTM A 351 Gr CF8M UNS S 32750/ 32760 UNS S 32750/ 32760 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M UNS S 32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy

Forged / Bar



Page 108 of 237

SHEET NO.


53364P



S10B API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1


Rev

50489-530-051-SPC-1002

B








ASME B 16.34


425 325

Air Test psi (g)

2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.

80

Description





Cover gasket

Spiral Wound

ASTM A 182 F 316/ 316L Dual Stamped 316/ 316L Dual Stamped 316/ 316L Dual Stamped Inconel X-750 ASTM A 182 F 316/ 316L Dual Stamped 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy



Page 109 of 237

SHEET NO.


53364



S10B

Manuf. Standard

BS 1868

Testing Standard

API 598/ BS 6755 Part-1


Rev

50489-530-051-SPC-1002

B








ASME B 16.34


425 325

Air Test psi (g)

2. This valve datasheet is applicable for Process Gas (PG), Blowdown (BD) & Fuel Gas (FG) services only.

80

Description





Cover gasket

Spiral Wound

ASTM A 351 Gr CF8M SS 316L SS 316L ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy

Forged / Bar



Page 110 of 237



Q15A

Manuf. Standard

API 594

Testing Standard

API 598

Services / Fluids

Brackish Water

SHEET NO. 53378D Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Valve Type

CHECK VALVE Dual plate check


3" - 24" 150# Special Requirements

Wafer Lug, 150 #, ASME B16.5, RF, Finish - 125 AARH

1. Straight length or any specific installation requirement shall be clearly specified by the vendor.

Pressure -Temperature Face to Face dimension ASME B 16.24 API 594 Rating Hydro Test Pressure 300 80 Body psi (g) Air Test psi (g) 225 Seat psi (g) Description Type of Construction Material of Construction Manufacturer's Alternate/ Acceptance Cast ASTM B 148-UNS C95800 Body Spring Loaded Plates (Discs) Monel / NI-AL-Bronze Body Seat RPTFE Plate Seat RPTFE Forged / Bar Hinge Pin Monel / NI-AL-Bronze Forged / Bar Stop Pin Monel / NI-AL-Bronze Inconel X-750 Spring Seal Welded (Note 6) ASTM B 148-UNS C95800 Retainers Plate Support Sleeve Monel / NI-AL-Bronze Monel / NI-AL-Bronze Other Wetted Parts Washer Bearings Monel / NI-AL-Bronze Silica Gel Retainer Packing Name Plate Corrosion Resistant SS / Ni Alloy General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Retainerless Design is also acceptable. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 8. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 9. Care should be taken to avoid galvanic corrosion by dissimlar metals.

Page 111 of 237

SHEET NO.


53378DF



C13B ( 4"- 12"), F10A (2"-24")


2"-24" 150# Special Requirements

Testing Standard

API 598

Services / Fluids

Potable Water / Fresh Water, Plant Air, Brackish Water

Wafer Lug, 150 #, ASME B16.5, FF, Finish - 125 AARH

ASME B 16.24

Face to Face dimension API 594

Description


B


API 594

300 225

Rev

50489-530-051-SPC-1002

Valve Type

Manuf. Standard



Air Test psi (g)




Cast ASTM B 148-UNS C95800 Body Spring Loaded Plates (Discs) Monel / NI-AL-Bronze (Note 10) Body Seat RPTFE Plate Seat RPTFE Forged / Bar Hinge Pin Monel / NI-AL-Bronze (Note 10) Forged / Bar Stop Pin Monel / NI-AL-Bronze (Note 10) Inconel X-750 Spring Seal Welded (Note 6) ASTM B 148-UNS C95800 Retainers Monel / NI-AL-Bronze (Note 10) Plate Support Sleeve B Monel / NI-AL-Bronze (Note 10) Other Wetted Parts Washer Bearings Monel / NI-AL-Bronze (Note 10) Silica Gel Retainer Packing Corrosion Resistant SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Retainerless Design is also acceptable. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 8. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 9. Care should be taken to avoid galvanic corrosion by dissimlar metals. 10. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .

B

Page 112 of 237

SHEET NO.


53379P




Q15B, F10B API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1

Rev

50489-530-051-SPC-1002

B




Effluent Water,Oily Water, Hydrocarbon Oil/ Condensate


ASME B 16.34


450 325


Air Test psi (g)

80




ASTM A 182 Gr F 53 UNS S32750/ 32760 UNS S32750/ 32760 Inconel X-750 ASTM A 182 Gr F 53 UNS S32750/ 32760 Compressed Non Asbestos Fibre ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy


Body Piston Seat Ring Spring Cover Guide Cover gasket B Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 113 of 237



Q15B

Manuf. Standard

API 594

Testing Standard

API 598

Services / Fluids

Hydrocarbon Oil/ Condensate, Oily Water

SHEET NO. 53379D Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Valve Type



2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.


ASME B 16.34 450 325 Type of Construction

Wafer Lug, 150 #, FF, ASME B16.5 (2"-24") 2. Straight length or any specific installation requirement shall be clearly FLGD, 150#, FF, ASME B16.47 'A' (26"-48"), specified by the vendor. Finish - 125 AARH Face to Face dimension API 594 Air Test psi (g)



Cast Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant

Body ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 114 of 237




SHEET NO. 53379DF Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Valve Type


API 598




Wafer Lug, 150 #, FF, ASME B16.5 (2"-24") FLGD, 150#, FF, ASME B16.47 'A' (26"-48"), Finish - 125 AARH

ASME B 16.34


F10B API 594


Air Test psi (g)

1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.




Body ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification.. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 115 of 237



F10A (1/2" - 1 1/2"), Q15A (1/2" - 2") MSS-SP-80

Testing Standard

BS 5154 / MSS-SP-80

Services / Fluids

Brackish Water

Flanged, 150#, ASME B 16.5 ,FF, Finish 125 AARH

ASME B 16.24


Description

350 250


Air Test psi (g)

53380P Contractor Document Number

Rev

50489-530-051-SPC-1002

B

CHECK VALVE Lift Check, Screwed Cover Spring Loaded Piston 1/2" - 2" 150# Special Requirements

Valve Type

Manuf. Standard


SHEET NO.

80



Cast Renewable / Integral Lift Type Bolted Nickel or Copper alloy (Note 4) Corrosion Resistant

ASTM B62 C83600 ASTM B62 C83600 Inconel X-750 ASTM B62 C83600 ASTM B62 C83600 To Manufacturer's Standard. ASTM A 193 Gr B7 SS / Ni Alloy


Body Seat Ring Spring Piston Cover Guide Cover gasket ASTM A 194 Gr 2H Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 6. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 7. Care should be taken to avoid galvanic corrosion by dissimlar metals.

Page 116 of 237



C13B MSS-SP-80

Testing Standard

BS 5154 / MSS-SP-80

Services / Fluids


SCRF, 3000# to NPT (F), ASME B 1.20.1

ASME B 16.24


Description

350 250


Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

CHECK VALVE Lift Check, Screwed Cover Spring Loaded Piston 1/2" - 3" 150# Special Requirements

Valve Type

Manuf. Standard


SHEET NO.

80



Cast Renewable / Integral Lift Type Screwd Nickel or Copper alloy (Note 4) Corrosion Resistant

ASTM B62 C83600 ASTM B62 C83600 Inconel X-750 ASTM B62 C83600 ASTM B62 C83600 To Manufacturer's Standard. ASTM A 193 Gr B7 SS / Ni Alloy


Body Seat Ring Spring Piston Cover Guide Cover gasket ASTM A 194 Gr 2H Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 6. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 7. Care should be taken to avoid galvanic corrosion by dissimlar metals.

Page 117 of 237

SHEET NO.


53399P



N10B, N10C API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1

Valve Type B



Rev

50489-530-051-SPC-1002

B

CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 2" 150# Special Requirements



Off Spec Crude Oil


ASME B 16.34


450 325

Air Test psi (g)

80




ASTM B564-UNS N06625 INCONEL 625 INCONEL 625 Inconel X-750 ASTM B564-UNS N06625 INCONEL 625 Compressed Non Asbestos Fibre ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy


Body Piston Seat Ring Spring Cover Guide Cover gasket Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 118 of 237

SHEET NO.


53399D



B

N10B (3" - 20") N10C (3" - 6")

Manuf. Standard

API 594

Testing Standard

API 598


B


Off Spec Crude Oil

ASME B 16.34



Air Test psi (g)

Rev

50489-530-051-SPC-1002

B


Valve Type


450 325






Forged Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant

Body ASTM B564-UNS N06625 Plates (Discs) INCONEL 625 Body Seat RPTFE Plate Seat RPTFE Hinge Pin INCONEL 625 Stop Pin INCONEL 625 Inconel X-750 Spring Retainers ASTM B564-UNS N06625 Plate Support Sleeve INCONEL 625 INCONEL 625 Other Wetted Parts Washer Bearings INCONEL 625 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 119 of 237

SHEET NO.


53411P




C35B




ASME B 16.34


Rev

50489-530-051-SPC-1002

B


Valve Type


1125 825



80

Description




Forged Renewable / Integral Bolted Forged / Bar

Cover gasket

Spiral Wound




Page 120 of 237

SHEET NO.


53411


14050489 C35B

Piping Class


Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard

BS 1868

Testing Standard

API 598/ BS 6755 Pt.1


Services / Fluids



ASME B 16.34




1125 825

Air Test psi (g)

80

Description



Body

Cast

ASTM A 216 Gr WCB

Seat Ring

Renewable

UNS S32750/ 32760


Bolted

Cover gasket

Spiral Wound

UNS S32750/ 32760 ASTM A 216 Gr WCB ASTM A 216 Gr WCB UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy

Forged / Bars


Cover Bolts / Nuts (Note 5) Name Plate Corrosion Resistant General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 121 of 237

SHEET NO.


53461



Services / Fluids


S30A BS 1868 API 598/ BS 6755 Part-1 Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor ASME B 16.34 1100 800

Rev

50489-530-051-SPC-1002

B


Valve Type Size Range Rating Ends Flanged, 300 #, ASME B16.5, RF, Finish - 125 AARH Face to Face dimension ASME B 16.10 Air Test psi (g)

80

Description





Cover gasket

Spiral Wound

ASTM A 351 Gr CF8M SS316 SS 316 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy

Forged / Bar



B

Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 122 of 237

SHEET NO.


53478



Q35A BS 1868

Testing Standard

API 598/ BS 6755 Part-1

Services / Fluids

Brackish Water


ASME B 16.34


775 575


Air Test psi (g)

B

80

Description





Cover gasket

Spiral Wound

ASTM B 148-UNS C95800 Monel / NI-AL-Bronze Monel / NI-AL-Bronze ASTM B 148-UNS C95800 ASTM B 148-UNS C95800 Monel / NI-AL-Bronze SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy

Forged / Bar

Rev

50489-530-051-SPC-1002 CHECK VALVE Swing check Bolted cover 3" - 24" 300# Special Requirements

Valve Type

Manuf. Standard




Note 7 Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 6. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 7. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.

Page 123 of 237



Q35A

Manuf. Standard

API 594

Testing Standard

API 598



Rev

50489-530-051-SPC-1002

B




Brackish Water

ASME B 16.24

Face to Face dimension API 594 Air Test psi (g)


53478D

Valve Type

Wafer Lug, 150 #, FF, ASME B16.5 (2"-24") FLGD, 150#, FF, ASME B16.47 'A' (26"-48"), Finish - 125 AARH

775 575

SHEET NO.




Cast ASTM B 148-UNS C95800 Body Spring Loaded Plates (Discs) Monel / NI-AL-Bronze Body Seat RPTFE Plate Seat RPTFE Forged / Bar Hinge Pin Monel / NI-AL-Bronze Forged / Bar Stop Pin Monel / NI-AL-Bronze Inconel X-750 Spring Seal Welded (Note 6) ASTM B 148-UNS C95800 Retainers Plate Support Sleeve Monel / NI-AL-Bronze Monel / NI-AL-Bronze Other Wetted Parts Washer Bearings Monel / NI-AL-Bronze Silica Gel Retainer Packing Corrosion Resistant SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Retainerless Design is also acceptable. 7. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 8. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 9. Care should be taken to avoid galvanic corrosion by dissimlar metals.

Page 124 of 237

SHEET NO.


53479P



Q35B, F30B


Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard


Testing Standard

API 598/ BS 6755 Pt. 1

Services / Fluids



ASME B 16.34





1125 825

Air Test psi (g)

80




ASTM A 182 Gr F 53 UNS S32750/ 32760 UNS S32750/ 32760 Inconel X-750 ASTM A 182 Gr F 53 UNS S32750/ 32760 Compressed Non Asbestos Fibre ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy


Body Piston Seat Ring Spring Cover Hinge Pin Cover gasket B Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 125 of 237



Q35B

Testing Standard


Services / Fluids



ASME B 16.34



Rev

50489-530-051-SPC-1002

B


API 598/ BS 6755 Pt. 1

Description



API 594

1125 825

53479D

Valve Type

Manuf. Standard


SHEET NO.

Air Test psi (g)






Page 126 of 237



Q35A

Manuf. Standard

API 594

Testing Standard

API 598



Rev

50489-530-051-SPC-1002

B



2" 300# Special Requirements

Brackish Water

ASME B 16.34



53482D

Valve Type


1125 825

SHEET NO.

Air Test psi (g)






Page 127 of 237



N30C

Manuf. Standard

API 594

Testing Standard

API 598



Rev

50489-530-051-SPC-1002

B




Off Spec Crude Oil

ASME B 16.34



53498D

Valve Type


1125 825

SHEET NO.

Air Test psi (g)





Body ASTM A 216 Gr WCB + 3 MM Inconel 625 Plates (Discs) INCONEL 625 Body Seat RPTFE Plate Seat RPTFE Hinge Pin INCONEL 625 Stop Pin INCONEL 625 Inconel X-750 Spring Retainers ASTM A 216 Gr WCB + 3 MM Inconel 625 Plate Support Sleeve INCONEL 625 INCONEL 625 Other Wetted Parts Washer Bearings INCONEL 625 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 128 of 237

SHEET NO.


53499P



N30B, N30C API 602/ BS EN ISO 15761 API 598/ BS 6755 Part-1


Rev

50489-530-051-SPC-1002

B

CHECK VALVE Lift Check, Bolted Cover Spring Loaded Piston 1/2" - 2" B 300# Special Requirements




Off Spec Crude Oil


ASME B 16.34


1125 825

Air Test psi (g)

80




ASTM B564-UNS N06625 INCONEL 625 INCONEL 625 Inconel X-750 ASTM B564-UNS N06625 INCONEL 625 Compressed Non Asbestos Fibre ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy


Body Piston Seat Ring Spring Cover Guide Cover gasket Cover Bolts / Nuts Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 129 of 237


14050489 N30B (3" - 16") N30C (3" - 6")



B

API 594 API 598


Rev

50489-530-051-SPC-1002

B




Off Spec Crude Oil

ASME B 16.34



53499D

Valve Type


1125 825

SHEET NO.

Air Test psi (g)




Forged Spring Loaded Forged / Bar Forged / Bar Seal Welded (Note 7) Corrosion Resistant

Body ASTM B564-UNS N06625 Plates (Discs) INCONEL 625 Body Seat RPTFE Plate Seat RPTFE Hinge Pin INCONEL 625 Stop Pin INCONEL 625 Inconel X-750 Spring Retainers ASTM B564-UNS N06625 Plate Support Sleeve INCONEL 625 INCONEL 625 Other Wetted Parts Washer Bearings INCONEL 625 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 130 of 237

SHEET NO.


53511P



C65B


Rev

50489-530-051-SPC-1002

B


Valve Type





ASME B 16.34




2225 1650

Air Test psi (g)

80

Description




Forged Renewable/ Integral Bolted Forged / Bar

Cover gasket

Spiral Wound



Cover Bolts / Nuts (Note 5) Name Plate Corrosion Resistant General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 131 of 237

SHEET NO.


53511


14050489 C65B

Piping Class


Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard

BS 1868

Testing Standard

API 598/ BS 6755 Pt. 1


Services / Fluids



ASME B 16.34




2225 1650

Air Test psi (g)

80

Description



Body

Cast

ASTM A 216 Gr WCB

Seat Ring

Renewable

UNS S32750/ 32760

Disc

-

UNS S32750/ 32760

Cover Hinge Hinge Pin / Guide

Bolted

Cover gasket

Spiral Wound

ASTM A 216 Gr WCB ASTM A 216 Gr WCB UNS S32750/ 32760 SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B7 ASTM A 194 Gr 2H SS / Ni Alloy

Forged / Bars



Page 132 of 237



C65B

B


Testing Standard

Services / Fluids

Hydrocarbon Gas / Oil / Condensate, Glycol


ASME B 16.34



Rev

50489-530-051-SPC-1002


API 598

Description



API 594

2225 1650

53511D

Valve Type

Manuf. Standard


SHEET NO.

Air Test psi (g)





Body ASTM A 216 Gr WCB UNS S32750/ 32760 Plates (Discs) Body Seat RPTFE Plate Seat RPTFE UNS S32750/ 32760 Hinge Pin UNS S32750/ 32760 Stop Pin Inconel X-750 Spring Retainers ASTM A 216 Gr WCB UNS S32750/ 32760 Plate Support Sleeve UNS S32750/ 32760 Other Wetted Parts UNS S32750/ 32760 Washer Bearings Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 133 of 237

SHEET NO.


53561



Services / Fluids


S60A BS 1868 API 598/ BS 6755 Part-1 Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, MEA Solution, Scale Inhibitor ASME B 16.34 2225 1650

Rev

50489-530-051-SPC-1002

B


Valve Type Size Range Rating Ends Flanged, 600 #, ASME B16.5, RF, Finish - 125 AARH Face to Face dimension ASME B 16.10 Air Test psi (g)

80

Description





Cover gasket

Spiral Wound

ASTM A 351 Gr CF8M SS316 SS 316 ASTM A 351 Gr CF8M ASTM A 351 Gr CF8M SS 316/ 316L Dual Stamped SS 316 Windings, Flexible Graphite Filled, CS Outer Ring and SS 316 Inner Ring ASTM A 193 Gr B8M ASTM A 194 Gr 8M SS / Ni Alloy

Forged / Bar



B Cover Bolts / Nuts Corrosion Resistant Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 134 of 237



Q95B API 594

Testing Standard

API 598

Services / Fluids

Effluent Water

Wafer Lug, 900 #, ASME B16.5, RTJ, Finish - 32 AARH

ASME B 16.34


Description



Air Test psi (g)

53679D Contractor Document Number

Rev

50489-530-051-SPC-1002

B


Valve Type

Manuf. Standard


SHEET NO.

3" - 20" 900# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Straight length or any specific installation requirement shall be clearly specified by the vendor.




Body ASTM A 995 Gr 5A/ 6A Plates (Discs) UNS S 32750 / 32760 Body Seat RPTFE Plate Seat RPTFE Hinge Pin UNS S 32750 / 32760 Stop Pin UNS S 32750 / 32760 Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A Plate Support Sleeve UNS S 32750 / 32760 UNS S 32750 / 32760 Other Wetted Parts Washer Bearings UNS S 32750 / 32760 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 135 of 237



Q95B API 602/ BS EN ISO 15761 API 598/ BS 6755 Pt. 1

SHEET NO. 53779P Contractor Document Number

Rev

50489-530-051-SPC-1002

B





Effluent Water


Flanged, 1500#, ASME B16.5, RTJ, Finish 32 complied. AARH Face to Face dimension ASME B 16.10 Air Test psi (g)



Forged Renewable/ Integral Bolted Forged / Bars Ring Type

Body ASTM A182 Gr F 53 Seat Ring UNS S 32750 / 32760 Spring Inconel X-750 Piston UNS S 32750 / 32760 Cover ASTM A182 Gr F 53 UNS S 32750 / 32760 Hinge Pin / Guide Cover gasket Super Duplex Oval Shape Gasket ASTM A 193 Gr B8M ASTM A 194 Gr 8M Cover Bolts / Nuts B Corrosion Resistant SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction shall be projected on valve body. 4 .Valve shall be suitable for horizontal and vertical services. 5. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015.

Page 136 of 237



Q95B

Manuf. Standard

API 594

Testing Standard

API 598



Rev

50489-530-051-SPC-1002

B



2" 1500# Special Requirements

Effluent Water

ASME B 16.34



53779D

Valve Type

Wafer Lug, 1500 #, ASME B16.5, RTJ, Finish - 32 AARH

5625 4125

SHEET NO.

Air Test psi (g)





Body ASTM A 995 Gr 5A/ 6A Plates (Discs) UNS S 32750 / 32760 Body Seat RPTFE Plate Seat RPTFE Hinge Pin UNS S 32750 / 32760 Stop Pin UNS S 32750 / 32760 Inconel X-750 Spring Retainers ASTM A 995 Gr 5A/ 6A Plate Support Sleeve UNS S 32750 / 32760 UNS S 32750 / 32760 Other Wetted Parts Washer Bearings UNS S 32750 / 32760 Silica Gel Retainer Packing SS / Ni Alloy Name Plate General Notes : 1. This valve specification sheet shall be read in conjunction with the technical notes to Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Flow direction and top of valve shall be projected on each valve. 4. Valve shall have independent plate suspension (hinge & support sleeve design), ensure reduction of friction and allow both plate to close at the same time. 5. Valve shall have independent spring for each plate to open and close without seat-scrubbing. 6. Third Party Inspection requirements shall be as per KOC Standard, KOC-MP-015. 7. Retainerless Design is also acceptable.

Page 137 of 237



C13A

Valve Type

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids


SW, 3000 # to ASME B 16.11, (Note 9)

ASME B 16.34





Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 1/2" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.



Forged ASTM A105 Body / Body Cover Solid Ball SS 316L (Note 10) Anti Blow Out (No Casting) Stem SS 316L Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr Steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 15) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 15) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 15) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at each end of valve prior to valve assembly. Refer Annexure III for nipple details. Page 138 of 237




Rev

50489-530-051-SPC-1002

B

Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 15. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B633.

Page 139 of 237



C13A

Valve Type

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids


SCRM X SCRF, NPT, 3000#, ASME B 1.20.1, (Note 9)

ASME B 16.34





Air Test psi (g)

SHEET NO. 54001S Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.



Forged ASTM A105 Body / Body Cover Solid (Note 10) Ball SS 316L Anti Blow Out (No Casting) Stem SS 316L Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr Steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 15) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 15) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 15) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with screwed NPT (F) X NPT (M) end, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Open end of nipple shall be NPT (M). Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 140 of 237




Rev

50489-530-051-SPC-1002

B

Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 15. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.

Page 141 of 237



C13A

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids




Valve Type Size Range Rating Ends SW X SCRF (NPT), 3000# to ASME B 16.11, (Note 9)

SHEET NO. 54001X Contractor Document Number

Rev

50489-530-051-SPC-1002

B





ASTM A105 Forged Body / Body Cover Solid (Note 10) Ball SS 316L Anti Blow Out (No Casting) Stem SS 316L Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr Steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 15) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A194 Gr 2H (Note 15) ASTM A193 Gr B7 Body Stud / Nuts (Note 15) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with SW X SCRD (F) ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 142 of 237




Rev

50489-530-051-SPC-1002

B

Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 15. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.

Page 143 of 237


14050489 S10A, S30A, S60A

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids

Instrument Air, Methanol Inhibitor, Antifoam Agent, Demulsifier, Oxygen Scavenger, Biocide, Scale Inhibitor, MEA Solution

SW, 3000 # to ASME B 16.11, (Note 9)

ASME B 16.34


Description



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B


Piping Class


SHEET NO.



Forged Body / Body Cover ASTM A182 Gr F316/ 316L Dual Stamped Solid (Note 10) SS 316/ 316L Dual Stamped Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 144 of 237




Rev

50489-530-051-SPC-1002

B

Ball Valveat 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded each end of valve prior to valve assembly. Refer Annexure III for nipple details. 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.

Page 145 of 237


14050489 S10A, S30A, S60A

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids



ASME B 16.34


Description



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B


Piping Class


SHEET NO.



Forged Body / Body Cover ASTM A182 Gr F316/ 316L Dual Stamped Solid (Note 10) SS 316/ 316L Dual Stamped Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 146 of 237




Rev

50489-530-051-SPC-1002

B

Ball(150mm Valve long) welded at one end of valve 9. For Soft Seated Ball Valves with screwed NPT (F) X NPT (M) end, manufacturer/ vendor shall supply those valves complete with pipe nipples prior to valve assembly. Open end of nipple shall be NPT (M). Refer Annexure III for nipple details. Other end of valve shall be NPT (F). 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.

Page 147 of 237



S10A, S30A, S60A

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids





SW X SCRF (NPT), 3000# to ASME B 16.11, (Note 9)


Rev

50489-530-051-SPC-1002

B





Forged Body / Body Cover ASTM A182 Gr F316/ 316L Dual Stamped Solid (Note 10) SS 316/ 316L Dual Stamped Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts B Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 148 of 237




Rev

50489-530-051-SPC-1002

B

Valve 9. For Soft Seated Ball Valves with SW X SCRD (F) ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mmBall long) welded at one end of valve prior to valve assembly. Refer Annexure III for nipple details. Other end of valve shall be NPT (F). 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.

Page 149 of 237



F30A, Q35A

Valve Type

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids

Brackish Water

SW, 3000 # to ASME B 16.11, (Note 9)

ASME B 16.34





Air Test psi (g)


Rev

50489-530-051-SPC-1002

B




Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at each end of valve prior to valve assembly. Refer Annexure III for nipple details. Page 150 of 237




Rev

50489-530-051-SPC-1002

B

Ball 10.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall beValve trunnion mounted. 11. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 12. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 13. Soft Seated Valves shall be provided with Anti-Static Device. 14. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.

Page 151 of 237



F30A

Valve Type

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids

Brackish Water

SW, 3000 # to ASME B 16.11, (Note 9)

ASME B 16.34





Air Test psi (g)

SHEET NO. 54082Y Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 1/2" - 1 1/2" 800# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side. 2. Ball Valve shall be spring loaded



Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever B ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with socket weld ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at each end of valve prior to valve assembly. Refer Annexure III for nipple details. Page 152 of 237



SHEET NO. 54082Y Contractor Document Number

Rev

50489-530-051-SPC-1002

B


Page 153 of 237



F30A, Q35A

Valve Type

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids

Brackish Water


ASME B 16.34





Air Test psi (g)


Rev

50489-530-051-SPC-1002

B




Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with screwed NPT (F) X NPT (M) end, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Open end of nipple shall be NPT (M). Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 154 of 237




Rev

50489-530-051-SPC-1002

B


Page 155 of 237



F30A, Q35A

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids

Brackish Water



Valve Type Size Range Rating Ends SW X SCRF (NPT), 3000# to ASME B 16.11, (Note 9)


Rev

50489-530-051-SPC-1002

B





Forged Body / Body Cover ASTM A182 Gr F53 Solid (Note 10) Ball UNS S32750 / S32760 Anti Blow Out (No Casting) Stem UNS S32750 / S32760 Bolted / Retained by Nuts & Washer Gland UNS S32750 / S32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9. For Soft Seated Ball Valves with SW X SCRD (F) ends, manufacturer/ vendor shall supply those valves complete with pipe nipples (150mm long) welded at one end of valve prior to valve assembly. Refer Annexure III for nipple details. Other end of valve shall be NPT (F). Page 156 of 237




Rev

50489-530-051-SPC-1002

B


Page 157 of 237




C13A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Fuel Oil (Diesel), Inert Gas ASME B 16.34 450 325 Type of Construction


Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 2" - 16" Rating 150# Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, RF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D Air Test psi (g)



Cast ASTM A216 Gr WCB) Body / Body Cover Solid (Note 9) Ball SS 316L (Note 15) Anti Blow Out (No Casting) SS 316L Stem Bolted / Retained by Nuts & Washer ASTM A105 / SS 316L / 13% Cr steel Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded.

Page 158 of 237




Rev

50489-530-051-SPC-1002

B

Ball Valve 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 14" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm ENP Coating.

Page 159 of 237


Manuf. Standard Testing Standard



Rev

50489-530-051-SPC-1002

B



SHEET NO.

C15B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292




ASME B 16.34

Face to Face dimension API 6D/ ASME B16.10

450 325

Description


Body / Body Cover

Forged / Cast

Air Test psi (g)

Ball Valve FULL BORE Split Body, Side Entry 1/2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.



ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 36") UNS S32750 / S32760 (Note 15) UNS S32750 / S32760 ASTM A105N / UNS S32750 / S32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750

Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal (Note 14) Gland Retaining Nut Forged / Machined Wrench / Lever (Note 14) Body Stud / Nuts (Note 14) Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 160 of 237



Rev

50489-530-051-SPC-1002

B


10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 16" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.

Ball Valve

Page 161 of 237





Rev

50489-530-051-SPC-1002

B



SHEET NO.

C15B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Hydrocarbon Gas/ Condensate


ASME B 16.34

Face to Face dimension API 6D/ ASME B16.10

450 325

Description


Body / Body Cover

Forged / Cast

Air Test psi (g)

Ball Valve FULL BORE Split Body, Side Entry 1/2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side. 3. This valve data sheet is applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) Services only.



ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 36") SS 316L (Note 15) SS 316L ASTM A105N/ SS 316L RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750




10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 16" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm SS 316L Overlay.


Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 163 of 237



Services / Fluids


S10A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292



ASME B 16.34

Face to Face dimension API 6D


Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 2" - 12" 150# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.


425 325

SHEET NO.



Cast ASTM A 351 Gr CF8M Body / Body Cover Solid (Note 9) SS 316 Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 164 of 237




Rev

50489-530-051-SPC-1002

B

Valve mounted. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shallBall be trunnion 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.

Page 165 of 237



Services / Fluids Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g) Description Body / Body Cover

S10B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Condensate, Glycol ASME B 16.34 425 325


Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 12" Size Range 150# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 150#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body Bonnet cavity pressure to the upstream side. Face to Face dimension API 6D/ ASME B16.10 Air Test psi (g)

80



Forged / Cast

ASTM A 182 Gr F 316/ 316L Dual Stamped (1/2" - 1 1/2")/ ASTM A 351 Gr CF8M (2" - 12")


Solid (Note 9) UNS S32750/ S32760 Ball Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 166 of 237



11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.


Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 167 of 237




S10B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Condensate ASME B 16.34 425 325


Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 12" Size Range 150# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 150#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body Bonnet cavity pressure to the upstream side. 3. This valve data sheet is applicable for Process Gas (PG), Blowdown (BD) and Fuel Gas (FG) Services only. Face to Face dimension API 6D/ ASME B16.10 Air Test psi (g)

80



Forged / Cast



Solid (Note 9) SS 316L Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts B Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 168 of 237





Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 169 of 237




Q15A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water



Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 3" - 24" Size Range 150# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, RF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D Air Test psi (g)



Cast Body / Body Cover ASTM B 148 UNS C95800 Solid (Note 9) Ball Monel / NI-AL-Bronze Anti Blow Out (No Casting) Stem Monel / NI-AL-Bronze Bolted / Retained by Nuts & Washer Gland Monel / NI-AL-Bronze Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 170 of 237





Rev

50489-530-051-SPC-1002

B

Ball Valve

14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.

Page 171 of 237




C13B (2"-12") F10A (2"-24") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water, Potable/ Fresh Water, Plant Air ASME B 16.24 300 225 Type of Construction


Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 2" - 24" Rating 150# Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side. Flanged, 150#, ASME B16.5, FF, Finish 125 AARH Face to Face dimension API 6D Air Test psi (g)



Cast Body / Body Cover ASTM B 148 UNS C95800 Solid (Note 9) Ball Monel / NI-AL-Bronze (Note 17) Anti Blow Out (No Casting) Stem Monel / NI-AL-Bronze (Note 17) B Bolted / Retained by Nuts & Washer Gland Monel / NI-AL-Bronze (Note 17) Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material. 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 172 of 237




Rev

50489-530-051-SPC-1002

B

C13BLock-Open (2"-12") (LO)/ Lock-Closed (LC) provision. 11. All Ball-Valves shall be provided with 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.

Ball Valve

14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 17. Pipe class C13B shall have Trim material as NI-AL-Bronze only and Pipe class F10A shall have Trim material as Monel / NI-AL-Bronze .

B

Page 173 of 237



Services / Fluids



Rev

50489-530-051-SPC-1002

B



SHEET NO.

C15B (0.5"-2") F10B (0.5"-1.5") Q15B (0.5"-36") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Hydrocarbon Gas/ Oil/ Condensate, Glycol, Oily Water, Effluent Water

Flanged, 150#, ASME B 16.5/ B 16.47 Series A, RF, Finish 125 AARH

ASME B 16.34

Face to Face dimension API 6D/ ASME B 16.10

450 325

Description


Body / Body Cover

Forged / Cast

Ball Valve Valve Type

Air Test psi (g)

FULL BORE Split Body, Side Entry 1/2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.



ASTM A 182 Gr F 53 (1/2" - 3")/ ASTM A 995 Gr 5A/ 6A (4" - 36") (Note 14) UNS S32750/ 32760 (Note 14) UNS S32750/ 32760 UNS S32750/ 32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B8M ASTM A194 Gr 8M ASTM A193 Gr B8M SS/ Ni Alloy Inconel X-750

Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal Gland Retaining Nut Forged / Machined Wrench / Lever Body Stud / Nuts B Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. Page 174 of 237




Rev

50489-530-051-SPC-1002

B

8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.

Page 175 of 237




F10B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water, Oily Water


Valve Type Size Range Rating Ends Flanged, 150#, ASME B 16.5/ B 16.47 Series A, RF, Finish 125 AARH


Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 2" - 36" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.

API 6D Air Test psi (g)



Cast Body / Body Cover ASTM A 995 Gr 5A/ 6A (Note 14) Solid (Note 9) Ball UNS S32750/ 32760 (Note 14) Anti Blow Out (No Casting) Stem UNS S32750/ 32760 Bolted / Retained by Nuts & Washer Gland UNS S32750/ 32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 176 of 237




Rev

50489-530-051-SPC-1002

B

Ball Valve 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.

Page 177 of 237




F10A (0.5"-1.5") Q15A (0.5"-2") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water



Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 2" Size Range 150# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, FF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)



Body / Body Cover Cast ASTM B62 UNS C83600 Ball Solid (Note 9) Bronze/ Monel Stem Anti Blow Out (No Casting) Bronze/ Monel Gland Bolted / Retained by Nuts & Washer Bronze/ Monel Body Seat Soft Seat (Note 7) RPTFE Body Seals Soft Seal RPTFE/ PTFE/ Graphoil Stem Seal Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Gland Retaining Nut (Note 16) ASTM A194 Gr 2H Wrench / Lever Forged / Machined Carbon Steel / Malleable Iron Body Stud / Nuts (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Gland Bolts (Note 16) ASTM A193 Gr B7 Name Plate Corrosion Resistant SS/ Ni Alloy Spring Inconel X-750 General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. Page 178 of 237




Rev

50489-530-051-SPC-1002

B

Ball Valve 14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.

Page 179 of 237




F10A (0.5"-1.5") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water


SHEET NO. 54380YF Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 1 1/2" Size Range 150# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 150#, ASME B16.5, FF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. 2. Ball Valve shall be spring loaded AARH Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)



Body / Body Cover Cast ASTM B62 UNS C83600 Ball Solid (Note 9) Bronze/ Monel Stem Anti Blow Out (No Casting) Bronze/ Monel Gland Bolted / Retained by Nuts & Washer Bronze/ Monel Body Seat Soft Seat (Note 7) RPTFE Body Seals Soft Seal RPTFE/ PTFE/ Graphoil Stem Seal Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Gland Retaining Nut (Note 16) ASTM A194 Gr 2H Wrench / Lever Forged / Machined Carbon Steel / Malleable Iron Body Stud / Nuts (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Gland Bolts (Note 16) ASTM A193 Gr B7 Name Plate Corrosion Resistant SS/ Ni Alloy Spring Inconel X-750 General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. Page 180 of 237



SHEET NO. 54380YF Contractor Document Number

Rev

50489-530-051-SPC-1002

B

Ball Valve 14. Any bronze alloy used in cold-worked condition shall be capable of passing the 'Mercurous-Nitrate Test' in accordance with ASTM B 154 to minimize susceptibility to stress corrosion. 15. Care should be taken to avoid galvanic corrosion by dissimlar metals. 16. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.

Page 181 of 237



C13B

Valve Type

Manuf. Standard

BS EN ISO 17292

Testing Standard

BS EN ISO 17292

Services / Fluids


SCRF, 150# to NPT(F), ASME B 1.20.1

ASME B 16.24





Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 1/2" -11/2" 150# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.



Cast ASTM B62 UNS C83600 Body / Body Cover Solid (Note 9) ASTM B62 UNS C83600 Ball Anti Blow Out (No Casting) Ni Al Bronze Stem Bolted / Retained by Nuts & Washer Ni Al Bronze Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr B7 Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 182 of 237





Rev

50489-530-051-SPC-1002

B

Ball Valve


Page 183 of 237




N10C API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Off Spec Crude Oil

Flanged, 150#, ASME B 16.5, RF, Finish 125 AARH

ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B




Cast Body / Body Cover ASTM A216 Gr WCB) + 3 mm Inconel 625 Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 184 of 237



11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.


Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 185 of 237


14050489 Piping Class B



N10B (0.5" - 20") N10C (0.5" - 6") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Off Spec Crude Oil


ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 1/2" - 20" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.



Forged ASTM B564-UNS N06625 (Note 15) Body / Body Cover Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr 2H Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 186 of 237




Rev

50489-530-051-SPC-1002

B

Ball Valve (0.5" - 20") (LO)/ Lock-Closed (LC) provision. 11. All Ball-Valves shall be providedN10B with Lock-Open 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Valves with Carbon Steel Body (ASTM A105N [0.5"-1.5"] & ASTM A216 GR WCB [2"-6"]) with 3 mm Inconel 625 lining may be considered if size permits.

Page 187 of 237





Rev

50489-530-051-SPC-1002

B



SHEET NO.

C35B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Oil/ Condensate, Glycol ASME B 16.34 1125 825

Description


Body / Body Cover

Forged / Cast

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 14" Rating 300# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)



ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 14") UNS S32750 / S32760 UNS S32750 / S32760 ASTM A105N / UNS S32750 / S32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750




10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.


Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 189 of 237



Services / Fluids





ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B



1100 800

SHEET NO.



Cast Body / Body Cover ASTM A 351 Gr CF8M Solid (Note 9) SS 316 Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 190 of 237




Rev

50489-530-051-SPC-1002

B


Page 191 of 237




S30B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Condensate, Glycol ASME B 16.34 1100 800


Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 1/2" - 16" Size Range 300# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, RF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body Bonnet cavity pressure to the upstream side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)

80



Forged / Cast



Solid (Note 9) UNS S32750/ S32760 Ball Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 192 of 237





Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 193 of 237




Q35A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Brackish Water



Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 3" - 32" Rating 300# Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to Flanged, 300#, ASME B16.5, RF, Finish 125 relief the Body Bonnet cavity pressure to the upstream side. AARH Face to Face dimension API 6D Air Test psi (g)



Cast Body / Body Cover ASTM B 148 UNS C95800 Solid (Note 9) Ball Monel / NI-AL-Bronze Anti Blow Out (No Casting) Stem Monel / NI-AL-Bronze Bolted / Retained by Nuts & Washer Gland Monel / NI-AL-Bronze Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 16) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 16) ASTM A193 Gr B7 Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 194 of 237





Rev

50489-530-051-SPC-1002

B

Ball Valve


Page 195 of 237


14050489 F30A


API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292

Services / Fluids

Brackish Water


ASME B 16.24 775 575


Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry 2" - 24" Size Range 300# Rating Ends Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side. Flanged, 300#, ASME B16.5, FF, Finish 125 AARH Face to Face dimension API 6D Air Test psi (g)

80

Description



Body / Body Cover

Cast

ASTM B 148 UNS C95800

Ball

Solid (Note 9)

Monel / NI-AL-Bronze


Stem Anti Blow Out (No Casting) Monel / NI-AL-Bronze Gland Bolted / Retained by Nuts & Washer Monel / NI-AL-Bronze Body Seat Soft Seat (Note 7) RPTFE Body Seals Soft Seal RPTFE/ PTFE/ Graphoil Stem Seal Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Gland Retaining Nut (Note 16) ASTM A194 Gr B7 Wrench / Lever Forged / Machined Carbon Steel / Malleable Iron Body Stud / Nuts (Note 16) ASTM A193 Gr B7 ASTM A194 Gr 2H Gland Bolts (Note 16) ASTM A193 Gr B7 Name Plate Corrosion Resistant SS/ Ni Alloy Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. Page 196 of 237



13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.


Rev

50489-530-051-SPC-1002

B

Ball Valve


Page 197 of 237





Rev

50489-530-051-SPC-1002

B



SHEET NO.

C35B (0.5"-8") F30B (0.5"-1.5") Q35B (0.5"-24")

API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Hydrocarbon Gas/ Oil/ Condensate, Glycol, Oily Water, Effluent Water ASME B 16.34 1125 825

Description


Body / Body Cover

Forged / Cast




ASTM A 182 Gr F 53 (1/2" - 3")/ ASTM A 995 Gr 5A/ 6A (4" - 24") (Note 14) UNS S32750/ 32760 (Note 14) UNS S32750/ 32760 UNS S32750/ 32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B8M ASTM A194 Gr 8M ASTM A193 Gr B8M SS/ Ni Alloy Inconel X-750

Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal Gland Retaining Nut Forged / Machined Wrench / Lever B Body Stud / Nuts Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 198 of 237




Rev

50489-530-051-SPC-1002

B

C35B (0.5"-8") Ball Valve 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14.Ball valves in the size range of 16" and above can have Body & Ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.

Page 199 of 237




F30B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water, Oily Water



Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 2" - 24" Rating 300# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 300#, ASME B16.5, FF, Finish 125 2. Floating Ball Valves shall be provided with pressure equalisation seals to AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D Air Test psi (g)



Cast Body / Body Cover ASTM A 995 Gr 5A/ 6A (Note 14) Solid (Note 9) Ball UNS S32750/ 32760 (Note 14) Anti Blow Out (No Casting) Stem UNS S32750/ 32760 Bolted / Retained by Nuts & Washer Gland UNS S32750/ 32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 200 of 237




Rev

50489-530-051-SPC-1002

B


Page 201 of 237




Q35A API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Brackish Water


ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

A

Ball Valve FULL BORE Split Body, Side Entry 2" 300# Special Requirements 1. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body Bonnet cavity pressure to the upstream side.



Cast Body / Body Cover ASTM A 995 Gr 5A/ 6A Solid (Note 9) Ball UNS S32750/ 32760 Anti Blow Out (No Casting) Stem UNS S32750/ 32760 Bolted / Retained by Nuts & Washer Gland UNS S32750/ 32760 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever B ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 202 of 237





Rev

50489-530-051-SPC-1002

A

Ball Valve

Page 203 of 237




N30C API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Off Spec Crude Oil


ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B




Cast Body / Body Cover ASTM A216 Gr WCB) + 3 mm Inconel 625 Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr 2H Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 204 of 237



11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633.


Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 205 of 237


14050489 Piping Class B



N30B (0.5" - 16") N30C (0.5" - 6") API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292


Off Spec Crude Oil


ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B

Ball Valve FULL BORE Split Body, Side Entry 1/2" - 16" B 300# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. Floating Ball Valves shall be provided with pressure equalisation seals to relief the Body-Bonnet cavity-pressure, to the upstream-side.



Forged ASTM B564-UNS N06625 (Note 15) Body / Body Cover Solid (Note 9) Ball Inconel 625 Anti Blow Out (No Casting) Stem Inconel 625 Bolted / Retained by Nuts & Washer Gland Inconel 625 Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal (Note 14) ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever (Note 14) ASTM A193 Gr B7 ASTM A194 Gr 2H Body Stud / Nuts (Note 14) ASTM A193 Gr 2H Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 206 of 237




Rev

50489-530-051-SPC-1002

B

Ball Valve (0.5" - 16") (LO)/ Lock-Closed (LC) provision. 11. All Ball-Valves shall be providedN30B with Lock-Open 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Valves with Carbon Steel Body (ASTM A105N [0.5"-1.5"] & ASTM A216 GR WCB [2"-6"]) with 3 mm Inconel 625 lining may be considered if size permits.

Page 207 of 237





Rev

50489-530-051-SPC-1002

B



SHEET NO.


Description


Body / Body Cover

Forged / Cast




ASTM A105N (1/2" - 1 1/2")/ ASTM A216 Gr WCB (2" - 24") UNS S32750/ S32760 (Note 15) UNS S32750/ S32760 ASTM A105N / UNS S32750/ S32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B7 ASTM A194 Gr 2H ASTM A193 Gr B7 SS/ Ni Alloy Inconel X-750

Solid (Note 9,15) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal (Note 14) Gland Retaining Nut Forged / Machined Wrench / Lever (Note 14) Body Stud / Nuts (Note 14) Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 208 of 237



Rev

50489-530-051-SPC-1002

B


10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033. 14. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 15. Ball valves in the size range of 16" and above can have ball MOC as CS (ASTM A216 GR WCB/ A105N) + 3 mm Inconel 625 Overlay.

Ball Valve

Page 209 of 237



Services / Fluids





ASME B 16.34



Air Test psi (g)


Rev

50489-530-051-SPC-1002

B



2175 1600

SHEET NO.



Cast Body / Body Cover ASTM A 351 Gr CF8M Solid (Note 9) SS 316 Ball Anti Blow Out (No Casting) SS 316/ 316L Dual Stamped Stem Bolted / Retained by Nuts & Washer SS 316/ 316L Dual Stamped Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. Page 210 of 237




Rev

50489-530-051-SPC-1002

B


Page 211 of 237





Rev

50489-530-051-SPC-1002

B



SHEET NO.


Description


Body / Body Cover

Forged / Cast




ASTM A 182 Gr F 53 (1/2" - 1 1/2")/ ASTM A 995 Gr 5A/ 6A (2" - 6") UNS S32750/ 32760 UNS S32750/ 32760 UNS S32750/ 32760 RPTFE RPTFE/ PTFE/ Graphoil RPTFE/ PTFE V Rings with Graphoil/ Graphoil ASTM A194 Gr 2H Carbon Steel / Malleable Iron ASTM A193 Gr B8M ASTM A194 Gr 8M ASTM A193 Gr B8M SS/ Ni Alloy Inconel X-750

Solid (Note 9) Ball Anti Blow Out (No Casting) Stem Bolted / Retained by Nuts & Washer Gland Soft Seat (Note 7) Body Seat Soft Seal Body Seals Renewable with valve open on stream Stem Seal Gland Retaining Nut Forged / Machined Wrench / Lever Body Stud / Nuts B Gland Bolts Corrosion Resistant Name Plate Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. Page 212 of 237



10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. 11. All Ball-Valves shall be provided with Lock-Open (LO)/ Lock-Closed (LC) provision. 12. Soft Seated Valves shall be provided with Anti-Static Device. 13. `Foundry-Qualification' requirements shall be as per KOC Standard, KOC-MP-033.


Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 213 of 237




Q95B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water



Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 3" - 24" Rating 900# Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 900#, ASME B16.5, RTJ, Finish 32- 2. Floating Ball Valves shall be provided with pressure equalisation seals to 63 AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D Air Test psi (g)



Cast ASTM A 995 Gr 5A/ 6A (Note 14) Body / Body Cover Solid (Note 9) Ball UNS S32750/ S32760 (Note 14) Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever B ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 214 of 237




Rev

50489-530-051-SPC-1002

B


Page 215 of 237




Q95B API 6D/ BS EN ISO 17292 API 6D/ BS EN ISO 17292 Effluent Water



Rev

50489-530-051-SPC-1002

B

Ball Valve Valve Type FULL BORE Split Body, Side Entry Size Range 1/2" - 2" 1500# Rating Ends Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Flanged, 1500#, ASME B16.5, RTJ, Finish 32- 2. Floating Ball Valves shall be provided with pressure equalisation seals to 63 AARH relief the Body-Bonnet cavity-pressure, to the upstream-side. Face to Face dimension API 6D/ ASME B 16.10 Air Test psi (g)



Forged Body / Body Cover ASTM A 182 Gr F 53 Solid (Note 9) Ball UNS S32750/ S32760 Anti Blow Out (No Casting) UNS S32750/ S32760 Stem Bolted / Retained by Nuts & Washer UNS S32750/ S32760 Gland Soft Seat (Note 7) RPTFE Body Seat Soft Seal RPTFE/ PTFE/ Graphoil Body Seals Renewable with valve open on stream RPTFE/ PTFE V Rings with Graphoil/ Graphoil Stem Seal ASTM A194 Gr 2H Gland Retaining Nut Forged / Machined Carbon Steel / Malleable Iron Wrench / Lever ASTM A193 Gr B8M ASTM A194 Gr 8M Body Stud / Nuts B ASTM A193 Gr B8M Gland Bolts Corrosion Resistant SS/ Ni Alloy Name Plate Inconel X-750 Spring General Notes : 1.This valve specification sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Valve shall be provided with position indicator. 4. All Ball Valves shall be provided with bi-directional shut-off. 5. All Ball Valves shall be of fire safe design. Fire test shall be as per API 607 IV Edition/ BS EN ISO 10497 (BS 6755 Part II) / API RP 6FA. 6. Bidder shall provide Pressure-Temperature Table/ Graph for the offered Soft Seat material 7. For trunion mounted Ball Valves, Body Seats shall be spring loaded. 8. Stem Seal / Body Seal in Graphoil shall be provided with corrosion inhibitor. 9.Ball Valves shall be either floating type or trunnion mounted for sizes NPS 1/2 to NPS 3. However the Ball Valve sizes NPS 4 and over shall be trunnion mounted. 10. All Ball-Valves above NPS 4 shall be provided with Double Block and Bleed (DBB) arrangement as per KOC Standard, KOC-MP-033. Page 216 of 237





Rev

50489-530-051-SPC-1002

B

Ball Valve

Page 217 of 237

SHEET NO.


55411

KOC Contract No


Rev

50489-530-051-SPC-1002

B

VALVE MATERIAL SPECIFICATION 14050489 Piping Class

C35B

Manuf. Standard Testing Standard Services (Sour) Pressure -Temperature Rating Hydro Test Pressure Body psi (g) Seat psi (g)

API 599 BS 6755 Pt. 1 / API 598 Hydrocarbon Oil / Condensate, Glycol ASME B 16.34 1125 825

Description

PLUG VALVE Valve Type PRESSURE BALANCED, TAPER PLUG Short Pattern 1/2" - 12" Size Range 300# Rating Ends Special Requirements Flanged, 300#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B16.10 Air Test psi (g)

80



Wrench

(Note 4)

Carbon Steel / SS / SG Iron

Name Plate

Corrosion Resistant

SS / Ni Alloy

Firesafe

Graphite / Graphite Filament

Emergency Packing injectable on stream

Manufacturer's Standard (Non Asbestos)

(Note 13)

ASTM A 193 Gr B7

Cover Gasket

Spiral Wound


Gland

Renewable with valve open on stream

ASTM A 105N / ASTM A 216 Gr WCB

Plug

Inverted Taper

Stem

Forged / Bar

Cover

Forged/ Cast


Body

Forged/ Cast



Stem Seal Cover Bolts / Nuts

ASTM A 194 Gr 2H

ASTM A 105N / ASTM A 216 WCB / WCC + ENP + Anti friction impregnated ASTM A 105N / AISI 4140 / 17-4 PH + Anti friction impregnated

Page 218 of 237



Rev

50489-530-051-SPC-1002

B

VALVE MATERIAL SPECIFICATION 14050489

PLUG VALVE General Notes : 1.This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Vendor shall supply bolting for the tapped holes if any as per ASME B 16.5. 4. For wrench-operated Plug-Valves, separate wrench shall be provided for each Plug-Valve. 5. All Plug Valves shall be of fire safe design. Fire safe test shall be as per API 607 IV Edition / BS EN ISO 10497 ( BS 6755 Part II ) /API RP 6FA. 6. Seating surface shall be stellied for abrasion and chloride resistance. Soft Seats to achieve a seal between body and plug shall not be accepted. 7. All Plug Valves shall be provided with position indicator 8. Vendor shall confirm suitability of lubricant with respect to service & service conditions specified 9. Vendor shall supply lubricant for two years of normal operation. 10. Unless otherwise specified in MR , valves shall be Short Pattern type upto 12" & Venturi type above 12" size. 12. All Plug Valves shall have provision of seat sealant injection under full line pressure. 13. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 14. Third party inspection shall be conducted as per KOC Standard, KOC-MP-016.

Page 219 of 237

SHEET NO.


55511

KOC Contract No


Rev

50489-530-051-SPC-1002

B


C65B

Manuf. Standard

API 599

Testing Standard

BS 6755 Pt. 1 / API 598

Services (Sour)



2225 1650

Description



Flanged, 600#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH Face to Face dimension ASME B16.10

ASME B 16.34


Valve Type

PLUG VALVE PRESSURE BALANCED, TAPER PLUG

Air Test psi (g)

80



Wrench

(Note 4)


Name Plate

Corrosion Resistant

SS / Ni Alloy

Firesafe

Graphite/ Graphite Filament



Cover Bolts / Nuts

(Note 13)

ASTM A 193 Gr B7

Cover Gasket

Spiral Wound


Gland



Plug

Inverted Taper

ASTM A 105N / ASTM A 216 WCB / WCC + ENP + Anti friction impregnated

Stem

Forged / Bar

ASTM A 105N / AISI 4140 / 17-4 PH + Anti friction impregnated

Cover

Forged/ Cast


Body

Forged/ Cast



Stem Seal ASTM A 194 Gr 2H

Page 220 of 237



Rev

50489-530-051-SPC-1002

B


PLUG VALVE General Notes : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Vendor shall supply bolting for the tapped holes if any as per ASME B 16.5. 4. For wrench-operated Plug-Valves, separate wrench shall be provided for each Plug-Valve. 5. All Plug Valves shall be of fire safe design. Fire safe test shall be as per BS EN ISO 10497 ( BS 6755 Part II ) /API RP 6FA. 6. Seating surface shall be stellied for abrasion and chloride resistance. Soft Seats to achieve a seal between body and plug shall not be accepted. 7. All Plug Valves shall be provided with position indicator 8. Vendor shall confirm suitability of lubricant with respect to service & service conditions specified 9. Vendor shall supply lubricant for two years of normal operation. 10. Unless otherwise specified in MR , valves shall be Short Pattern type upto 12" & Venturi type above 12" size. 12. All Plug Valves shall have provision of seat sealant injection under full line pressure. 13. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 14. Third party inspection shall be conducted as per KOC Standard, KOC-MP-016.

Page 221 of 237

SHEET NO.


B

KOC Contract No

55511L Contractor Document Number

Rev

50489-530-051-SPC-1002

B


C65B

Manuf. Standard

API 599

Testing Standard

BS 6755 Pt. 1 / API 598

Services (Sour)



ASME B 16.34


2225 1650

Description

Valve Type

PLUG VALVE PRESSURE BALANCED, TAPER PLUG



Flanged, 600#, ASME B16.5, RF, Finish 125 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. AARH 2. Valve shall be provided with Limit Switches as per applicable KOC standard. Face to Face dimension ASME B16.10 Air Test psi (g)

80



Wrench

(Note 4)


Name Plate

Corrosion Resistant

SS / Ni Alloy

Firesafe

Graphite/ Graphite Filament



Cover Bolts / Nuts

(Note 13)

ASTM A 193 Gr B7

Cover Gasket

Spiral Wound


Gland



Plug

Inverted Taper

ASTM A 105N / ASTM A 216 WCB / WCC + ENP + Anti friction impregnated

Stem

Forged / Bar

ASTM A 105N / AISI 4140 / 17-4 PH + Anti friction impregnated

Cover

Forged/ Cast


Body

Forged/ Cast



Stem Seal ASTM A 194 Gr 2H

Page 222 of 237


SHEET NO. B

55511L Contractor Document Number

Rev

50489-530-051-SPC-1002

B


PLUG VALVE General Notes : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. Vendor shall supply bolting for the tapped holes if any as per ASME B 16.5. 4. For wrench-operated Plug-Valves, separate wrench shall be provided for each Plug-Valve. 5. All Plug Valves shall be of fire safe design. Fire safe test shall be as per BS EN ISO 10497 ( BS 6755 Part II ) /API RP 6FA. 6. Seating surface shall be stellied for abrasion and chloride resistance. Soft Seats to achieve a seal between body and plug shall not be accepted. 7. All Plug Valves shall be provided with position indicator 8. Vendor shall confirm suitability of lubricant with respect to service & service conditions specified 9. Vendor shall supply lubricant for two years of normal operation. 10. Unless otherwise specified in MR , valves shall be Short Pattern type upto 12" & Venturi type above 12" size. 12. All Plug Valves shall have provision of seat sealant injection under full line pressure. 13. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 14. Third party inspection shall be conducted as per KOC Standard, KOC-MP-016.

Page 223 of 237

SHEET NO.


56311

KOC Contract No


Rev

50489-530-051-SPC-1002

B


C15B

Manuf. Standard

API 609 Cat B

Testing Standard

API 598

Services (Sour)



ASME B 16.34 450 325

BUTTERFLY VALVE Valve Type Size Range Rating Ends WAFL, 150# RF ASME B16.5 (3" -24")

3" - 24" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied.

Face to Face dimension API 609 Cat B Air Test psi (g)

80

Description



Handwheel

Cast / Fabricated

Ductile Iron/ Malleable Iron / Cast Steel

Name Plate

Corrosion Resistant

SS/ Ni Alloy UNS S32750 / S32760

Shaft Bushing Shaft seal

Renewable

Graphite with Inconel Wire

Disc Seal

Replaceble


Clamping Rings (If required) Bolts


UNS S32750 / S32760 Nuts

Machined

ASTM A193 Gr B7

ASTM A 194 Gr 2H

UNS S32750 / S32760

Body Screws / Pin Shaft

Anti Static, No Casting

UNS S32750 / S32760

Body Seat

Renewable

UNS S32750 / S32760

Disc

Cast

UNS S32750 / S32760

Body

Cast

ASTM A 216 Gr WCB

Page 224 of 237



Rev

50489-530-051-SPC-1002

B


BUTTERFLY VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Bidder to furnish cross sectional details of body seat / seal arrangement with the offer 5. Bolting for Tapped holes in body, if any, shall be supplied by vendor in material ASTM A 193 GR.B7/A 194 GR.2H. 6. Valves shall be provided with position indicator and locking device at any position 7. Valves shall be tight shut off and shall be bi-directional. 8. Valves shall be of fire safe design as per API 607 or ISO 10497 or API 6FA. 9. Shaft seal shall be provided with corrosion inhibitor

Page 225 of 237

SHEET NO.


56312

KOC Contract No


Rev

50489-530-051-SPC-1002

B


C15B

Manuf. Standard

API 609 Cat B

Testing Standard

API 598

Services (Sour)

Hydrocarbon Gas/ Oil/ Condensate


ASME B 16.34 450 325

BUTTERFLY VALVE Valve Type Size Range Rating Ends WAFL, 150# RF ASME B16.5 (3" -24")

3" - 24" 150# Special Requirements 1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This Valve Data Sheet shall be applicable for Process Gas (PG), Fuel Gas (FG) and Blowdown (BD) services only

Face to Face dimension API 609 Cat B Air Test psi (g)

80

Description



Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy SS316L


Renewable


Disc Seal

Replaceble




SS316L Nuts

Machined

ASTM A193 Gr B7

ASTM A 194 Gr 2H

SS316L



SS316L

Body Seat

Renewable

SS316L

Disc

Cast

ASTM A 216 Gr WCB + SS316 overlay

Body

Cast

ASTM A 216 Gr WCB

Page 226 of 237



Rev

50489-530-051-SPC-1002

B


BUTTERFLY VALVE GENERAL NOTES : 1. This valve material sheet shall be read in conjunction to technical notes of Valve Material Specification. 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Bidder to furnish cross sectional details of body seat / seal arrangement with the offer 5. Bolting for Tapped holes in body, if any, shall be supplied by vendor in material ASTM A 193 GR.B7 / A 194 GR.2H. 6. Valves shall be provided with position indicator and locking device at any position 7. Valves shall be tight shut off and shall be bi-directional. 8. Valves shall be of fire safe design as per API 607 or ISO 10497 or API 6FA. 9. Shaft seal shall be provided with corrosion inhibitor

Page 227 of 237

SHEET NO.


56381

KOC Contract No


Rev

50489-530-051-SPC-1002

B


Q15A

Manuf. Standard

API 609 Cat B

Testing Standard

API 598

Services (Sour)

Brackish Water


ASME B 16.24 300 220

BUTTERFLY VALVE Valve Type Size Range Rating Ends


WAFL, 150#, RF ASME B16.5 (3" -24") Face to Face dimension API 609 Cat B Air Test psi (g)

80

Description



Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy Ni Al Bronze / Monel


Renewable


Disc Seal

Replaceble




Ni Al Bronze / Monel Nuts

Machined

ASTM A193 Gr B7

ASTM A 194 Gr 2H

Ni Al Bronze / Monel




Body Seat

Renewable


Disc

Cast


Body

Cast

ASTM A 216 Gr WCB - EPDM Lined

Page 228 of 237



Rev

50489-530-051-SPC-1002

B



Page 229 of 237

SHEET NO.


56478

KOC Contract No


Rev

50489-530-051-SPC-1002

B


Q35A

Manuf. Standard

API 609 Cat B

Testing Standard

API 598

Services (Sour)

Brackish Water


ASME B 16.24


300 220

BUTTERFLY VALVE Valve Type Size Range Rating Ends


WAFL, 150# RF ASME B16.5 (3" -24") Face to Face dimension API 609 Cat B Air Test psi (g)

80

Description



Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy Ni Al Bronze / Monel


Renewable


Disc Seal

Replaceble




Ni Al Bronze / Monel Nuts

Machined

ASTM A193 Gr B7

ASTM A 194 Gr 2H





Bonnet Gasket

Flat Ring

Compressed Non-Asbestos Fibre

Body Seat

Renewable

Ni Al Bronze / Monel Ni Al Bronze / Monel

Disc Body

Cast

ASTM B 148 C95800

Page 230 of 237



Rev

50489-530-051-SPC-1002

B



Page 231 of 237

SHEET NO.


57082

KOC Contract No


Rev

50489-530-051-SPC-1002

B


Q35A

Manuf. Standard

BS EN ISO 15761

Testing Standard

API 598/ BS 6755 Pt. 1

Services

NEEDLE VALVE OS &Y Bolted Bonnet 1/2" - 1 1/2" 800# Special Requirements


Hydrocarbon Oil / Condensate, Oily Water

SW, 3000 # to ASME B 16.11

ASME B 16.34



3000 2200

Air Test psi (g)

80

Description



Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy

Stem Sleeve/ Nut

Forged/ Machined

ASTM A 439 Type D-2 / D-2C

Stem

Forged / Bar (No Casting)

UNS S32750/ S32760

Gland Packing

Renewable with Valve on stream


Back Seat Bush

-

UNS S32750/ S32760

Bonnet Bolts / Nuts

ASTM A 193 Gr B8M


ASTM A 194 Gr 8M

Bonnet

Bolted

ASTM A 182 Gr F 53

Bonnet Gasket

Flat Ring

Compressed Non-Asbetos Fibre

Body Seat Ring

Renewable / Integral

UNS S32750/ S32760

Disc

Loose Plug Type

UNS S32750/ S32760

Body

Forged

ASTM A 182 Gr F 53

B

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 4. Gland packing shall be provided with corrosion Inhibitors

Page 232 of 237

SHEET NO.


57311

KOC Contract No


Rev

50489-530-051-SPC-1002

B


C15B

Manuf. Standard

BS EN ISO 15761

Testing Standard

API 598/ BS 6755 Pt. 1



1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. Services

Hydrocarbons Gas / Oil / Condensate, Glycol

Flanged, 150#, ASME B16.5

ASME B 16.34



450 325

Air Test psi (g)

80

Description




Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy

Stem Sleeve/ Nut

Forged/ Machined


Stem


UNS S32750 / S32760

Gland Packing



Back Seat Bush

-

UNS S32750 / S32760

Bonnet Bolts / Nuts

(Note 3)

ASTM A 193 Gr B7

Bonnet

Bolted

ASTM A 105N

Bonnet Gasket

Spiral Wound


Body Seat Ring


UNS S32750 / S32760

Disc

Loose Plug Type

UNS S32750 / S32760

Body

Forged

ASTM A 105N

ASTM A 194 Gr 2H

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 3. All Alloy Steel bolting shall be electro-zinc plated in accordance with ASTM B 633. 4. Gland packing shall be provided with corrosion Inhibitors Page 233 of 237

SHEET NO.


57312

KOC Contract No


Rev

50489-530-051-SPC-1002

B


C15B

Manuf. Standard

BS EN ISO 15761

Testing Standard

API 598/ BS 6755 Pt. 1

Services



Hydrocarbons Gas / Oil / Condensate


ASME B 16.34



450 325

Air Test psi (g)

1. NACE requirements as per NACE MR 0175 / ISO 15156 shall be complied. 2. This Valve Data Sheet shall be applicable for Process Gas (PG), Fuel Gas (FG) and Blowdown (BD) services only.

80

Description




Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy

Stem Sleeve/ Nut

Forged/ Machined


Stem


SS316L

Gland Packing



Back Seat Bush

-

SS316L

Bonnet Bolts / Nuts

(Note 3)

ASTM A 193 Gr B7

Bonnet

Bolted

ASTM A 105N

Bonnet Gasket

Spiral Wound


Body Seat Ring


SS316L

Disc

Loose Plug Type

SS316L

Body

Forged

ASTM A 105N

ASTM A 194 Gr 2H


SHEET NO.


57379

KOC Contract No


Rev

50489-530-051-SPC-1002

B


Q15B

Manuf. Standard

BS EN ISO 15761

Testing Standard

API 598/ BS 6755 Pt. 1




Hydrocarbon Oil / Condensate, Oily Water


ASME B 16.34



450 325

Air Test psi (g)

80

Description



Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy

Stem Sleeve/ Nut

Forged/ Machined


Stem


UNS S32750 / S32760

Gland Packing



Back Seat Bush

-

UNS S32750/ S32760

Bonnet Bolts / Nuts

ASTM A 193 Gr B8M


ASTM A 194 Gr 8M

Bonnet

Bolted

ASTM A 182 Gr F 53

Bonnet Gasket

Flat Ring

Compressed Non-Asbetos Fibre

Body Seat Ring


UNS S32750 / S32760

Disc

Loose Plug Type

UNS S32750 / S32760

Body

Forged

ASTM A 182 Gr F 53

B

GENERAL NOTES : 1. This valve specification sheet shall be read in conjunction with Requirements of Valve Material Specification (Shts. 03 through 19). 2. This data sheet shall be completely filled-up by the vendor, stamped, signed and deviations if any, clearly marked for technical-review & acceptance. Quotation without this valve data sheet shall not be considered for technical review. 4. Gland packing shall be provided with corrosion Inhibitors

Page 235 of 237

SHEET NO.


57411

KOC Contract No


Rev

50489-530-051-SPC-1002

B


C35B

Manuf. Standard

BS EN ISO 15761

Testing Standard

API 598/ BS 6755 Pt. 1





Hydrocarbons Oil / Condensate, Glycol


ASME B 16.34



1125 825

Air Test psi (g)

80

Description




Handwheel

Cast / Fabricated


Name Plate

Corrosion Resistant

SS/ Ni Alloy

Stem Sleeve/ Nut

Forged/ Machined


Stem


UNS S32750 / S32760

Gland Packing



Back Seat Bush

-

UNS S32750 / S32760

Bonnet Bolts / Nuts

(Note 3)

ASTM A 193 Gr B7

Bonnet

Bolted

ASTM A 105N

Bonnet Gasket

Spiral Wound


Body Seat Ring


UNS S32750 / S32760

Disc

Loose Plug Type

UNS S32750 / S32760

Body

Forged

ASTM A 105N

ASTM A 194 Gr 2H


Project Title CONSTRUCTION OF NEW GATHERING CENTRE GC 30, IN NORTH KUWAIT KOC Contract No


14050489


Rev

50489-530-051-SPC-1002

B

APPENDIX-III TABLE – 2: BALL VALVE NIPPLE DETAILS Sr. No.

Sheet No.

Piping Class

Size (Inch)

Nipple Description

1

54001

C13A

0.5

PIPE NIPPLE SEAMLESS PBE 1/2" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M

2

54001, 54001X

C13A

0.75

PIPE NIPPLE SEAMLESS PBE 3/4" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M

3

54001, 54001X

C13A

1

PIPE NIPPLE SEAMLESS PBE 1" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M

4

54001, 54001X

C13A

1.5

PIPE NIPPLE SEAMLESS PBE 1 1/2" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN END ASME B36.10M

5

54001S

C13A

0.5

PIPE NIPPLE SEAMLESS TOE 1/2" X 150MM API 5L GRADE B PSL1 SCH XS PLAIN X THREADED (NPT M) ASME B36.10M

6

54082

F30A, Q35A

0.5

PIPE NIPPLE SEAMLESS PBE 1/2" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M

7

54082, 54082X

F30A, Q35A

0.75

PIPE NIPPLE SEAMLESS PBE 3/4" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M

8

54082, 54082X

F30A, Q35A

1

PIPE NIPPLE SEAMLESS PBE 1" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M

9

54082, 54082X

F30A, Q35A

1.5

PIPE NIPPLE SEAMLESS PBE 1 1/2" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 40S PLAIN END ASME B36.19M

10

54082S

F30A, Q35A

0.5

PIPE NIPPLE SEAMLESS TOE 1/2" X 150MM ASTM A790 UNS S32750 ANNEALED SCH 80S PLAIN X THREADED (NPT M) ASME B36.19M

11

54061

S10A, S30A, S60A

0.5

PIPE NIPPLE SEAMLESS PBE 1/2" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M

12

54061, 54061X

S10A, S30A, S60A

0.75

PIPE NIPPLE SEAMLESS PBE 3/4" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M

13

54061, 54061X

S10A, S30A, S60A

1

PIPE NIPPLE SEAMLESS PBE 1" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M

14

54061, 54061X

S10A, S30A, S60A

1.5

PIPE NIPPLE SEAMLESS PBE 1 1/2" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 40S PLAIN END ASME B36.19M

15

54061S

S10A, S30A, S60A

0.5

PIPE NIPPLE SEAMLESS TOE 1/2" X 150MM ASTM A312 GRADE TP 316/316L DUAL STAMPED SCH 80S PLAIN X THREADED (NPT M) ASME B36.19M

KOC Piping Specification

Recommend Documents