Poleas y fajas
ISO 22:1991 Belt drives -- Flat transmission belts and corresponding pulleys -- Dimensions and tolerances ISO 155:1998 Belt drives -- Pulleys -- Limiting values for adjustment of centres ISO 251:2012 Conveyor belts with textile carcass -- Widths and lengths ISO 252:2007 Conveyor belts -- Adhesion between constitutive elements -- Test methods ISO 254:2011 Belt drives -- Pulleys -- Quality, finish and balance ISO 255:1990 Belt drives -- Pulleys for V-belts (system based on datum width) -- Geometrical inspection of grooves ISO 282:1992 Conveyor belts -- Sampling ISO 283:2015 Textile conveyor belts -- Full thickness tensile strength, elongation at break and elongation at the reference load -- Test method ISO 284:2012 Conveyor belts -- Electrical conductivity -- Specification and test method ISO 340:2013 Conveyor belts -- Laboratory scale flammability characteristics -- Requirements and test method ISO 433:1991 Conveyor belts -- Marking ISO 433:1991/Amd 1:2006 ISO 505:1999 Conveyor belts -- Method for the determination of the tear propagation resistance of textile conveyor belts ISO 583:2007 Conveyor belts with a textile carcass -- Total belt thickness and thickness of constitutive elements -- Test methods ISO 703:2007 Conveyor belts -- Transverse flexibility (troughability) -- Test method ISO 1081:2013 Belt drives -- V-belts and V-ribbed belts, and corresponding grooved pulleys -- Vocabulary ISO 1120:2012 Conveyor belts -- Determination of strength of mechanical fastenings -- Static test method ISO 1604:1989 Belt drives -- Endless wide V-belts for industrial speed-changers and groove profiles for corresponding pulleys ISO 1813:2014 Belt drives -- V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts -- Electrical conductivity of antistatic belts: Characteristics and methods of test
ISO 2790:2004 Belt drives -- V-belts for the automotive industry and corresponding pulleys -- Dimensions ISO 3410:1989 Agricultural machinery -- Endless variable-speed V-belts and groove sections of corresponding pulleys ISO 3684:1990 Conveyor belts -- Determination of minimum pulley diameters ISO 3684:1990/Amd 1:2006 ISO 3870:1976 Conveyor belts (fabric carcass), with length between pulley centres up to 300 m, for loose bulk materials -- Adjustment of take-up device ISO 4183:1995 Belt drives -- Classical and narrow V-belts -- Grooved pulleys (system based on datum width) ISO 4184:1992 Belt drives -- Classical and narrow V-belts -- Lengths in datum system ISO 4195:2012 Conveyor belts with heat-resistant rubber covers -- Heat resistance of covers -- Requirements and test methods ISO 5284:1986 Conveyor belts -- List of equivalent terms ISO 5284:1986/Cor 1:2005 ISO 5285:2012 Conveyor belts -- Guidelines for storage and handling ISO 5287:2003 Belt drives -- Narrow V-belts for the automotive industry -- Fatigue test ISO 5288:2001 Synchronous belt drives -- Vocabulary ISO 5289:1992 Agricultural machinery -- Endless hexagonal belts and groove sections of corresponding pulleys ISO 5290:2001 Belt drives -- Grooved pulleys for joined narrow V-belts -- Groove sections 9N/J, 15N/J and 25N/J (effective system) ISO 5291:2011 Belt drives -- Grooved pulleys for joined classical V-belts -- Groove sections AJ, BJ, CJ and DJ (effective system) ISO 5292:1995 Belt drives -- V-belts and V-ribbed belts -- Calculation of power ratings ISO 5293:2004 Conveyor belts -- Determination of minimum transition distance on three idler rollers ISO 5293:2004/Cor 1:2008 ISO 5294:2012 Synchronous belt drives -- Pulleys ISO 5295:1987 Synchronous belts -- Calculation of power rating and drive centre distance
ISO 5296:2012 Synchronous belt drives -- Belts with pitch codes MXL, XXL, XL, L, H, XH and XXH -- Metric and inch dimensions ISO 7590:2009 Steel cord conveyor belts -- Methods for the determination of total thickness and cover thickness ISO 7622-1:2013 Steel cord conveyor belts -- Longitudinal traction test -- Part 1: Measurement of elongation ISO 7622-2:2015 Steel cord conveyor belts -- Longitudinal traction test -- Part 2: Measurement of tensile strength ISO 7623:2015 Steel cord conveyor belts -- Cord-to-coating bond test -- Initial test and after thermal treatment ISO 8094:2013 Steel cord conveyor belts -- Adhesion strength test of the cover to the core layer ISO 8370-1:1993 Belt drives -- Dynamic test to determine pitch zone location -- Part 1: V-belts ISO 8370-2:1993 Belt drives -- Dynamic test to determine pitch zone location -- Part 2: V-ribbed belts ISO 8419:2003 Belt drives -- Narrow V-belts -- Sections 9N/J, 15N/J and 25N/J (lengths in the effective system) ISO 9010:1997 Synchronous belt drives -- Automotive belts ISO 9011:1997 Synchronous belt drives -- Automotive pulleys ISO 9563:2015 Belt drives -- Electrical conductivity of antistatic endless synchronous belts -- Characteristics and test method ISO 9608:1994 V-belts -- Uniformity of belts -- Test method for determination of centre distance variation ISO 9856:2003 Conveyor belts -- Determination of elastic and permanent elongation and calculation of elastic modulus ISO 9856:2003/Amd 1:2012 ISO 9980:2012 Belt drives -- Grooved pulleys for V-belts (system based on effective width) -- Geometrical inspection of grooves ISO 9981:1998 Belt drives -- Pulleys and V-ribbed belts for the automotive industry -- PK profile: Dimensions ISO 9982:1998 Belt drives -- Pulleys and V-ribbed belts for industrial applications -- PH, PJ, PK, PL and PM profiles: dimensions ISO 10247:1990 Conveyor belts -- Characteristics of covers -- Classification ISO 10247:1990/Amd 1:2006 ISO 11749:2014 Belt drive -- V-ribbed belts for the automotive industry -- Fatigue test
ISO 12046:2012 Synchronous belt drives -- Automotive belts -- Determination of physical properties ISO 13050:2014 Synchronous belt drives -- Metric pitch, curvilinear profile systems G, H, R and S, belts and pulleys ISO 14890:2013 Conveyor belts -- Specification for rubber- or plastics-covered conveyor belts of textile construction for general use ISO 15147:2012 Light conveyor belts -- Tolerances on widths and lengths of cut light conveyor belts ISO 15236-1:2005 Steel cord conveyor belts -- Part 1: Design, dimensions and mechanical requirements for conveyor belts for general use ISO 15236-2:2004 Steel cord conveyor belts -- Part 2: Preferred belt types ISO 15236-3:2007 Steel cord conveyor belts -- Part 3: Special safety requirements for belts for use in underground installations ISO 15236-4:2004 Steel cord conveyor belts -- Part 4: Vulcanized belt joints ISO 16851:2012 Textile conveyor belts -- Determination of the net length of an endless (spliced) conveyor belt ISO 17396:2014 Synchronous belt drives -- Metric pitch, trapezoidal profile systems T and AT, belts and pulleys ISO 18573:2012 Conveyor belts -- Test atmospheres and conditioning periods ISO 19347:2015 Synchronous belt drives -- Imperial pitch trapezoidal profile system -- Belts and pulleys ISO 21178:2013 Light conveyor belts -- Determination of electrical resistances ISO 21179:2013 Light conveyor belts -- Determination of the electrostatic field generated by a running light conveyor belt ISO 21180:2013 Light conveyor belts -- Determination of the maximum tensile strength ISO 21181:2013 Light conveyor belts -- Determination of the relaxed elastic modulus ISO 21182:2013 Light conveyor belts -- Determination of the coefficient of friction ISO 21183-1:2005 Light conveyor belts -- Part 1: Principal characteristics and applications ISO 21183-2:2005 Light conveyor belts -- Part 2: List of equivalent terms ISO 22721:2007
Conveyor belts -- Specification for rubber- or plastics-covered conveyor belts of textile construction for underground mining ISO 24035:2014 Belt drives -- V-belts and the corresponding pulleys for agricultural machineries -- Dimensions Engranes ISO 53:1998 Cylindrical gears for general and heavy engineering -- Standard basic rack tooth profile ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering -- Modules ISO 677:1976 Straight bevel gears for general engineering and heavy engineering -- Basic rack ISO 678:1976 Straight bevel gears for general engineering and heavy engineering -- Modules and diametral pitches ISO 701:1998 International gear notation -- Symbols for geometrical data ISO 1122-1:1998 Vocabulary of gear terms -- Part 1: Definitions related to geometry ISO 1122-1:1998/Cor 1:1999 ISO 1122-1:1998/Cor 2:2009 ISO 1122-2:1999 Vocabulary of gear terms -- Part 2: Definitions related to worm gear geometry ISO 1328-1:2013 Cylindrical gears -- ISO system of flank tolerance classification -- Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth ISO 1328-2:1997 Cylindrical gears -- ISO system of accuracy -- Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information ISO 2490:2007 Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module -- Nominal dimensions ISO 4468:2009 Gear hobs -- Accuracy requirements ISO 4468:2009/Cor 1:2009 ISO 6336-1:2006 Calculation of load capacity of spur and helical gears -- Part 1: Basic principles, introduction and general influence factors ISO 6336-1:2006/Cor 1:2008 ISO 6336-2:2006 Calculation of load capacity of spur and helical gears -- Part 2: Calculation of surface durability (pitting)
ISO 6336-2:2006/Cor 1:2008 ISO 6336-3:2006 Calculation of load capacity of spur and helical gears -- Part 3: Calculation of tooth bending strength ISO 6336-3:2006/Cor 1:2008 ISO 6336-5:2003 Calculation of load capacity of spur and helical gears -- Part 5: Strength and quality of materials ISO 6336-6:2006 Calculation of load capacity of spur and helical gears -- Part 6: Calculation of service life under variable load ISO 6336-6:2006/Cor 1:2007 ISO 8579-1:2002 Acceptance code for gear units -- Part 1: Test code for airborne sound ISO 9083:2001 Calculation of load capacity of spur and helical gears -- Application to marine gears ISO 9085:2002 Calculation of load capacity of spur and helical gears -- Application for industrial gears ISO/TR 10064-1:1992 Code of inspection practice -- Part 1: Inspection of corresponding flanks of gear teeth ISO/TR 10064-1:1992/Cor 1:2006 ISO/TR 10064-2:1996 Code of inspection practice -- Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash ISO/TR 10064-2:1996/Cor 1:2001 ISO/TR 10064-2:1996/Cor 2:2006 ISO/TR 10064-3:1996 Code of inspection practice -- Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes ISO/TR 10064-3:1996/Cor 1:2006 ISO/TR 10064-4:1998 Code of inspection practice -- Part 4: Recommendations relative to surface texture and tooth contact pattern checking ISO/TR 10064-4:1998/Cor 1:2006 ISO/TR 10064-5:2005 Code of inspection practice -- Part 5: Recommendations relative to evaluation of gear measuring instruments ISO/TR 10064-5:2005/Cor 1:2006 ISO/TR 10064-6:2009 Code of inspection practice -- Part 6: Bevel gear measurement methods ISO 10300-1:2014 Calculation of load capacity of bevel gears -- Part 1: Introduction and general influence factors ISO 10300-2:2014 Calculation of load capacity of bevel gears -- Part 2: Calculation of surface durability (pitting)
ISO 10300-3:2014 Calculation of load capacity of bevel gears -- Part 3: Calculation of tooth root strength ISO 10825:1995 Gears -- Wear and damage to gear teeth -- Terminology ISO/TR 10828:2015 Worm gears -- Worm profiles and gear mesh geometry ISO 13691:2001 Petroleum and natural gas industries -- High-speed special-purpose gear units ISO 14104:2014 Gears -- Surface temper etch inspection after grinding, chemical method ISO/TR 14179-1:2001 Gears -- Thermal capacity -- Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature ISO/TR 14179-2:2001 Gears -- Thermal capacity -- Part 2: Thermal load-carrying capacity ISO/TR 14521:2010 Gears -- Calculation of load capacity of wormgears ISO 14635-1:2000 Gears -- FZG test procedures -- Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils ISO 14635-2:2004 Gears -- FZG test procedures -- Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils ISO 14635-3:2005 Gears -- FZG test procedures -- Part 3: FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases ISO/TR 15144-1:2014 Calculation of micropitting load capacity of cylindrical spur and helical gears -- Part 1: Introduction and basic principles ISO/TR 15144-2:2014 Calculation of micropitting load capacity of cylindrical spur and helical gears -- Part 2: Examples of calculation for micropitting ISO 17485:2006 Bevel gears -- ISO system of accuracy ISO 18653:2003 Gears -- Evaluation of instruments for the measurement of individual gears ISO/TR 18792:2008 Lubrication of industrial gear drives ISO 21771:2007 Gears -- Cylindrical involute gears and gear pairs -- Concepts and geometry ISO/TR 22849:2011 Design recommendations for bevel gears ISO 23509:2006
Bevel and hypoid gear geometry IEC 61400-4:2012 Wind turbines -- Part 4: Design requirements for wind turbine gearboxes Cadenas de eslabones de acero redondo, eslingas de cadena, componentes y accesorios Standard and/or project ISO 1834:1999 Short link chain for lifting purposes -- General conditions of acceptance ISO 1835:1980 Short link chain for lifting purposes -- Grade M (4), non-calibrated, for chain slings etc. ISO 1837:2003 Lifting hooks -- Nomenclature ISO 2308:1972 Hooks for lifting freight containers of up to 30 tonnes capacity -- Basic requirements ISO 2415:2004 Forged shackles for general lifting purposes -- Dee shackles and bow shackles ISO 3056:1986 Non-calibrated round steel link lifting chain and chain slings -- Use and maintenance ISO 3076:2012 Round steel short link chains for general lifting purposes -- Medium tolerance sling chains for chain slings -- Grade 8 ISO 3077:2001 Short-link chain for lifting purposes -- Grade T, (types T, DAT and DT), fine-tolerance hoist chain ISO 3266:2010 Forged steel eyebolts grade 4 for general lifting purposes ISO 3266:2010/Amd 1:2015 ISO 4778:1981 Chain slings of welded construction -- Grades M (4), S (6) and T (8) ISO 4779:1986 Forged steel lifting hooks with point and eye for use with steel chains of grade M(4) ISO 7592:1983 Calibrated round steel link lifting chains -- Guidelines to proper use and maintenance ISO 7593:1986 Chain slings assembled by methods other than welding -- Grade T(8) ISO 7597:2013 Forged steel lifting hooks with latch, grade 8 ISO 8539:2009 Forged steel lifting components for use with Grade 8 chain ISO 16798:2004
Standard and/or project Links of Grade 8 for use with slings ISO 16872:2015 Round steel short link chains for lifting purposes -- Fine tolerance hoist chains for hand operated chain hoists -- Grade VH ISO 16877:2015 Round steel short link chains for lifting purposes -- Fine tolerance hoist chains for hand operated chain hoists -- Grade TH ISO/TR 23602:2005 Toughness of chain steels
Cadenas y piñones de la cadena de transmisión de energía y transportadores ISO 487:1998 Steel roller chains, types S and C, attachments and sprockets ISO 606:2015 Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets ISO 1275:2006 Double-pitch precision roller chains, attachments and associated chain sprockets for transmission and conveyors ISO 1977:2006 Conveyor chains, attachments and sprockets ISO 3512:1992 Heavy-duty cranked-link transmission chains ISO 4347:2015 Leaf chains, clevises and sheaves -- Dimensions, measuring forces, tensile strengths and dynamic strengths ISO 6971:2002 Cranked-link drag chains of welded construction, attachments and sprockets ISO 6972:2002 Cranked-link mill chains of welded construction, attachments and sprockets ISO 6973:1986 Drop-forged rivetless chains for conveyors ISO 9633:2001 Cycle chains -- Characteristics and test methods ISO 10190:2008 Motorcycle chains -- Characteristics and test methods ISO 10823:2004 Guidelines for the selection of roller chain drives ISO 10823:2004/Cor 1:2008 ISO 13203:2005 Chains, sprockets and accessories -- List of equivalent terms
ISO 15654:2015 Fatigue test method for transmission precision roller chains and leaf chains