Otis TCB Svt

OTIS

FIELD COMPONENT MANUAL

Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1

Central & East Europe Area

FOD BERLIN

Service Tool Manual

Page:

1/ 35

TCB

Date:

17-Aug-2009

TCB Service Tool Manual

Authorization Date D1:

29-Feb-2000

Running on PCB:

GAA 26800 BA

Software Version:

GAA 30084 AAA

Document Revision : Date 03-Jul-2000

Author G. Priebe

Page 1 - 35

Comment Original Document

Copyright 2009, OTIS GmbH & Co. OHG Berlin. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of OTIS.

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

2/ 35

TCB

Date:

17-Aug-2009

Table of Contents 1

Introduction .............................................................................................3

2

Tree Structure..........................................................................................3

3

TCB Menu System ...................................................................................3 3.1 Overview ................................................................................................................... 3 3.2 Menu System ............................................................................................................ 4 3.2.1 System Path .......................................................................................................... 4 3.2.2 Tools Path ............................................................................................................. 5 3.2.3 Short Keys S4 – S9 ............................................................................................... 6 3.3 System – Menu ......................................................................................................... 8 3.3.1 Status – Menu ( <1> <1>) .............................................................................. 8 3.3.2 TEST - Functions ( <1> <2>) ...................................................................... 12 3.3.3 SETUP –Function ( <1> <3>) ...................................................................... 17 3.4 TOOLS – Function ( <2>) ................................................................................. 30 3.4.1 Search-IO – Function ( <2> <1>) ................................................................. 31 3.4.2 Erase-IO – Function ( <2> <2>) ................................................................... 32 3.4.3 Setup Install – Function ( <2> <3>) .............................................................. 32 3.4.4 Setup Door – Function ( <2> <4>) ............................................................... 33 3.4.5 Operate Memory ( <2> <9>) ........................................................................ 33

OTIS


1

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

3/ 35

TCB

Date:

17-Aug-2009

Introduction

The Service Tool is a pocket terminal that lets you control all elevator functions:   

Monitoring of software states, system inputs and outputs and system messages Setup of installation parameters Use of software tools.

All Service Tool functions are organized under a Tree-Structure. The access of each function is controlled by the TCB-Menu System which makes convenient work with the Service Tool possible. The Service Tool Manual describes the TCB-Menu System and the single Service Tool functions.

2

Tree Structure

All Service Tool functions are organized under the Tree-Structure which you can see below. It is divided in a SYSTEM path, where you have access to the main Service Tool functions  STATUS (system monitoring)  SETUP (setup of system environment) and in a TOOL path. The TOOLS path contains the Service Tool functions which supports installation and maintenance of the elevator.

3

TCB Menu System

3.1

Overview

The Menu System allows you to access the single Service Tool functions if you choose the right path through the Tree Structure by pressing the correspondingly key (number 1,2,...8). If there is only one number to choose, you can call the function also with the Shift key ”ENTER”. You can toggle between the different menus using the ”GOON” or ”GOBACK” key if the ”>” character indicates a hidden menu. The ”CLEAR” key lets you jump one step back. If you want to jump back to one the three Main Level of the architecture (MONITOR, FUNCTION or SET) you can do it with the ”M”, ”F” or ”S” Main Level Key.

OTIS


FOD BERLIN

3.2

Menu System

3.2.1

System Path

No.:

GBA 26800BA IV

Service Tool Manual

Page:

4/ 35

TCB

Date:

17-Aug-2009

TCB – Menu

M 1

2 TOOLS – Menu

(8)

SYSTEM - Menu

S

4 - AA3

Vintage: 01 / 1


F

Part:

1

2

STATUS – Menu

(8)

(see next page )

3 TEST – Menu

1

Calls

(9)

1

2

Inputs

(10)

2

3

Outputs

(11)

3

Part

(15)

4

Group

(11)

4

RSL

5

ICSS

(11)

5

Selftest

6

Cmd

(12)

Events

SETUP – Menu

(12) (13)

1

Diagnosis (14)

INSTALL – Menu 1

System

2

OCSS

(15)

3

Group

(16)

4

Drive

5

Doors

6

Pos. Ref.

7

Service

8

Emerg.

9

Security

goon

Page number

Test

RSL

3

ALLOWED – Menu (20)

Menu System

(13)

(18)

2

Legend: Service Tool Key 1

Function

(17)

(19)

1

Enabled

2

Cut Call

3

Card Rd

4

Pos

(23)

5

DCS - Run

(24)

6

ELD

(27)

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

3.2.2

Part:

Service Tool Manual

Page:

5/ 35

TCB

Date:

17-Aug-2009

Tools Path

M

TCB - Menu 1 SYSTEM - Menu

F

S

Legend: 1

Service Tool Key Menu System Function

(13)

Page number

2 TOOLS - Menu

(31)

1

Search IO

(31)

2

Erase IO

(32)

3

Setup INST

(32)

4

Setup Door

(33)

9

Opr. Memory (33)

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN 3.2.3

Part:

Service Tool Manual

Page:

6/ 35

TCB

Date:

17-Aug-2009

Short Keys S4 – S9

The Short Keys provide direct access to certain , often used Service Too functions, eliminating the need to step through the menu structure. The Service Tool functions Input, Calls, Install, RSL and Events are assigned to the Standard Short Keys S4 (Shift 4), S5 (Shift 5), S6 (Shift 6), S7 (Shift 7), S8 (Shift 8). Short Key S9 (Shift 9) is a free programmable key to store any position of the Tree – Structure as a sixth Short Key. Once you have stored S9 (by pressing S9 at the desired position) you can reset it only on level M (TCB – Menu).

S4 = Install S5 = RSL S6 = Event

S7 = Inputs S8 = Calls S9 = Prog

3.2.3.1 Standard Short Keys TCB – Menu

TOOLS – Menu

SYSTEM – Menu

STATUS – Menu

TEST – Menu

SETUP – Menu

Search IO Erase IO

S8

Calls

S6

Events

S4

Install Setup INST

S7

Input

Diagnosis

S5

RSL

Opr.Memory

Example A – 00 IDL ST ] [ ] [ u d l ux

The current function may be STATUS / Output

Short Key S8: Direct call of function STATUS / Calls

A – 00 IDL ST ] [ ] [ C < U00 D00 A 1 - C

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

7/ 35

TCB

Date:

17-Aug-2009

3.2.3.2 Programmable Short Key S9 TCB – Menu

TOOLS – Menu

SYSTEM – Menu

STATUS – Menu

TEST – Menu

SETUP – Menu

Search IO Erase IO

S8

Calls

S6

Events

S4

Install Setup INST

S7

Diagnosis

Input Output

9

Part

S5

5

RSL

Opr.Memory

Allowed

In the figure you can see the function of Short Key S9. In this example the function STATUS / Output is set to the Short Key S9 function. Now S9 is acting like a Standard Short Key. In the figure the current position is SETUP / RSL. Now you can call the function STATUS / Output with Short Key S9. Example A – 00 IDL ST ] [ ] [ u d l ux

Function STATUS / Output should be set as a Short Key Function: First you have to call STATUS / Output.

Short Key S9: Position STATUS / Output is set to the Short Key S9 function. Key MODULE and Shift Key ON: The status of Store Key S9 is displayed on the TCB-Menu.

TCB - Menu SVT-Key PROG: on

Short Key S9 and TCB-Menu: Reset of Short Key S9

TCB - Menu SVT-Key PROG: off

IO I AD P AD P >0000

Now you can toggle between any function SETUP / RSL and STATUS / Output.

Short Key S9: Call of function STATUS / Output.

A – 00 IDL ST ] [ ] [ u d l ux

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

8/ 35

TCB

Date:

17-Aug-2009

3.3 System – Menu 3.3.1

Status – Menu ( <1> <1>)

System-Menu = 1 Status-Menu = 1

SYSTEM – Menu Status=1 Test=2 STATUS – Menu Calls=1 Inputs=2 Car identifier

A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

A B C Direction

A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

U D Position

A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

00 ** OCSS mode

A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

IDL

MCSS state A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

ST

Doors states A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

][ ][

DDO

Description first car of group / Simplex second car in group third car in group Description top / direction not defined car is moving in UP direction car is moving in DOWN direction Description actual level (level 0) position not defined Description current OCSS –mode (Idle) see document: Service Tool Manual / Operational Modes Description current MCSS –state (Stop) See document: Service Tool Manual / Motion States Description front / rear door state: ] [ for Closed [ ] for Open <> for Opening >< for Closing ** for door state not defined when DDO switch was switched and doors are closed

OTIS


FOD BERLIN

A – 00 >TCI-LOCK ! C> U00 D00 A 1C

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


A – 00 INS IN ] [ ] [ C> U00 D00 A 1C

Part:

Service Tool Manual

Page:

9/ 35

TCB

Date:

17-Aug-2009

In additional a blinking Event Message will be displayed during Software Status Display if one of the following events occurs and the elevator is blocked. Examples: Event Message >TCI – LOCK ! >LS – Fault ! >start DCS ! >1LS+2LSon

Description ”Leave Top of Car” function on 1LS/2LS check negative Door Check Sequence not operated yet 1LS and 2LS is operated

3.3.1.1 Calls - Function ( <1> <1> <1>) Calls = 1

Short Key:

A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C

The first row displays the Software Status. The second row controls the Elevator Calling System. - You can enter a Car Call, Up Hall Call, Down Hall Call or Emergency Hospital Call - Monitoring of: - number of Upper and Lower Call demands - Load Status - number of cars available in group - power supply

Enter a call 1) 2)

Calls

A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C

S8

Call Type / Level Number

1)

C U D E

Car Call Up Hall Call Down Hall Call Emergency Hospital Call

2)

02

entered call (level 2)

With GOON / GOBACK you can toggle trough the Call Types C, U, D and E. 1)

2)

A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C

Call Demands 1)

01

number of UP-Call demands

2)

00

number of DOWN-Call demands

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

10/ 35

TCB

Date:

17-Aug-2009

Load Status A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C

A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C

A F P O D

ANS load full load peak load overload default load Cars available in group

1–3

number of cars available in group Power Supply

A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C A – 00 IDL ST ][ ][ C>02 U01 D00 A–1C 3.3.1.2 Input Function

Input = 2

C E

Normal power supply Emergency power supply

( <1> <1> <2>) Short Key:

S7

A – 00 IDL ST ] [ ] [ ins es dw DFC

The first row displays the Software Status. The second row monitors the System Inputs. - lower case letters of the input name stands for ”Function = OFF” and upper case letters for ”Function = ON”. - Up to four signals are displayed in one group. You can skip to the next / previous group with Key GOON / GOBACK. - Each group is assigned to a functional block. Both can be displayed with ENTER. Please refer to the list of available System Inputs. ( see document: Service Tool Reference List)

A – 00 IDL ST md aes

Key GOON / Shift Key GOBACK: Skip to the next / previous group of the System Inputs.

][][

Shift Key UP / DOWN: Row one: Display of the functional block and the current group. SY1 Safety Chain ins es dw DFC

Safety Chain Shift Key ON: Jump to first page of inputs (safety chain)

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

11/ 35

TCB

Date:

17-Aug-2009

3.3.1.3 Output – Function ( <1> <1> <3>) Output = 3 A – 00 IDL ST ] [ ] [ u d l ux

The first row displays the Software Status. The second row monitors the System Outputs. - lower case letters of the output name stands for ”Function = OFF” and upper case letters for ”Function = ON”. - Up to four signals are displayed in one group. You can skip to the next / previous group with Key GOON / GOBACK. - Use Shift Key ENTER to display the current Drive Type instead of the Software Status. Please refer to the list of available System Inputs. ( see document: Service Tool Reference List)

A – 00 IDL ST ] [ ] [ v1 v2 v3 v4

Key GOON / Shift Key GOBACK: Skip to the next / previous group of the System Outputs. Shift Key UP / Shift Key DOWN: Row one: Display of the current Drive Type.

OVF20 > v1 v2 v3 v4

Drive: OVF20 3.3.1.4 Group – Function ( <1> <1> <4>) Group = 4 A – 00 IDL ST B – 03 IDL ST

][][ ][][

The first row displays the Software Status of the Controller the Service Tool is connected with. The second row displays the Software Status of one of the Other Controllers in the group.

Key GOON / GOBACK: Skip to the next / previous Controller in the group.

A – 00 IDL ST C – 07 IDL ST

][][ ][][

3.3.1.5 ICSS – Function ( <1> <1> <5>) ICSS = 5 ICSS IS ONLINE ICSS2 IS OFFLINE

The first row displays the status of the first ICSS. The second row displays the status of the second ICSS.

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

12/ 35

TCB

Date:

17-Aug-2009

3.3.1.6 Command – Function ( <1> <1> <6>) Cmd = 6 A – 00 IDL ST ] [ ] [ F:CLD1 R:CLD1

The first row displays the Software Status. The second row displays the Commands which are sent to the internal Subsystems. (see document: Service Tool Reference List / Commands)

1)

Display Field

A – 00 IDL ST ] [ ] [ F:CLD1 R:CLD1 2)

1) 2) 3)

IDL CLD1 CLD1

Description Software Status command for front door command for rear door

3)

With Key GOON / Shift Key GOBACK: skip to the next / previous group of commands. 1) A – 00 IDL ST ] [ ] [ MC: GoTo To: 00 2) 3)

Display Field

Description

1) 2) 3)

Software Status Motion command Actuell Target (** = invalid)

IDL GoTo 00

(Hint: There are more indications for DCSS5 (Door = 12)!) 3.3.2

TEST - Functions ( <1> <2>)

System-Menu = 1 Test-Menu =2

SYSTEM – Menu Status=1 Test=2 TEST – Menu > Events=1 Diag=2 TEST – Menu > Part=3 RSL=4 TEST – Menu > Selft.=5

There are the Events, Diagnosis, Part, RSL and Selftest functions, which are the most used functions for service and maintenance. Short Key S6 is assigned to call the Events-function. Part display the configuration number of EPROM and EEPROM. RSL and Selftest are functions to test the hardware of the TCB. 3.3.2.1 Event – Function ( <1> <2> <1>)

OTIS


FOD BERLIN Event = 1

1) 00000 00000

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


00000 00000

Part:

Service Tool Manual

Page:

13/ 35

TCB

Date:

17-Aug-2009

Short Key = S6 total runs minutes on

The Event – Function supports the maintenance of the elevator. It displays - the total number of runs - the elapsed time since Power On - information about each event: + event text + the number of events + the elapsed time since last occurrence + the car position where the last event occurred Please refer to the list of Event Messages. See document: Service Tool Reference List

2)

Global information

total runs minutes on

1) 2)

00000 00000

number of elevator runs minutes since Power On

With Key GOON / Shift Key GOBACK skip through the list of recorded event messages. Event logging Event logging 1) 0400 RSL parity c002 t00001 p** 2)

3)

1) 2) 3)

first row 002 00001

4)

**

4)

event text number of events since Power On elapsed time since last occurrence (minutes) car position where the last event occurred (** = position not defined)

Event reset - Shift Key ON: Resets the displayed event. -

Shift Key ENTER: Termination of the reset function.

-

Shift Key UP: Resets the entire event logging.

-

Key 1 and ENTER and Key 2 and ENTER: Termination of the reset function - Key CLEAR: back to Test- Menu

Erase Value ? done ! Erase Events ? n=0 y=1 > Erase Events ? please wait !

3.3.2.2 Diagnosis – Function ( <1> <2> <2>)

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

14/ 35

TCB

Date:

17-Aug-2009

Diagnosis = 2 01 DIAG ACT-T 000 : 00 : 00 : 34

The first row displays the name of the current diagnosis Parameter. The second row shows the value of the diagnosis parameter.

You can skip to the next / previous diagnosis parameter with Key GOON / GOBACK. With Key UP you can display a short legend for the time values. The displayed parameter can be reset to zero using the key sequence ON/UP and ENTER. Please refer to the list of Diagnosis Parameters. Diagnosis parameters display Example of a time parameter 1)

2)

01 DIAG TOT-T 007 : 05 : 11 : 30 3)

4)

5)

6)

Display Field 1) 2) 3) 4) 5) 6)

01 TOT-T 007 05 11 30

Description Parameter no. Parameter name No. of months No. of days No. of hours No. of minutes

Example of a count parameter 1)

2)

03 DIAG UP-CNT 000000081 3)

Display Field 1) 2) 3)

03 UP-CNT 000000081

Description Parameter no. Parameter name No. of occurrences

Diagnosis parameter reset Erase Value ? 02 DIAG TOT-T

-

Shift Key ON: Resets the displayed event.

-

Shift Key ENTER: Termination of the reset function.

-

Shift Key UP: Displays a short legend of the time value

Mon : d : h : min 007 : 05 : 11 : 30

-

Shift Key UP (a second time) Resets the entire event logging

Erase Events ? n=0 y=1 >

- Key 1 and ENTER and Key 2 and ENTER:

Erase Value ? done !

Erase Events ? please wait !

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

15/ 35

TCB

Date:

17-Aug-2009

Termination of the reset function. - Key CLEAR: back to Test -Menu 3.3.2.3 Part – Function ( <1> <2> <3>) Part = 3 No. GAA30084 AAA 11-Jul-1999 08:30

The Part – Function displays the current software version of the EPROM and EEPROM. It also displays the date and the time of the TCB software release.

With Key GOON / Shift Key GOBACK you can toggle between the displays of the EEPROM version and the display that shows the EPROM version and the date /time of the release. Key CLEAR: back to Test - Menu Software version / date / time EE=E47NE4711 11-Jul-1999 08:30 No. GAA30084 AAA 11-Jul-1999 08:30

1) E47NE4711 2) GAA30084AAA 3) 11-Jul-99 4) 08:30

EEPROM version EPROM version date and time of the release

3.3.2.4 RSL-Test Function ( <1> <2> <4>) RSL = 4 The RSL-Test Function can be used to test the Remote Stations. After the address of the Remote Station is entered, - the four Input Pins are monitored and - the four Output Pins can be set.

ADR=

Enter the RSL – address Key 1,5:

Input Keys of the RSL –address

ADR=15

Key CLEAR: deletes the last input if you want to correct the number Shift Key ENTER: termination of the input operation The current status of the Input and Output Pins of The entered RSL address is displayed.

ADR=15 IN:off

BIT=1 OUT:off

Key GOON / Shift Key GOBACK:

ADR=16 IN:off

BIT=1 OUT:off

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

16/ 35

TCB

Date:

17-Aug-2009

Skip to next / previous address. Shift Key UP / Shift Key DOWN: Skip to the next / previous bit.

ADR=16 IN:off

BIT=2 OUT:off

Shift Key ON / Shift Key OFF: Toggle of the Output-Pin: on / off

ADR=16 IN:off

BIT=2 OUT:on

Key Clear: Back to Test-Menu 1)

2) 3)

ADR=16 IN:off

RSL: Pin status 4)

BIT=1 OUT:off

(on = active / off = not active)

1) ADR 2) BIT 3) IN 4) OUT

RSL address RSL pin RSL Input Pin status (Monitor) RSL Output Pin status

3.3.2.5 Selftest –Function ( <1> <2> <5>) Selftest = 5 PR ?

EE ? RS ?

RA ?

Function Selftest can be used - to test the memory of the TCB board and - to check the Remote Serial Link. The test will start as soon as the Selftest –Function is called.

The flashing question mark indicates which part of the test is currently active: - PR EPROM -test - EE EEPROM –test - RA RAM –test - RS Remote Serial Link –test The single results are displayed as: - (+) for Test successfully finished - (-) for Test not successfully finished Please notice that for the EE –test a checksum written into the EEPROM is verified. So, the first call of the test with a new EEPROM will result a (-). PR +

EE RS ?

RA ?

PR +

EE + RA + RS 16aR000

PR +

EE + RA + RS 16aR000

The RS –test will give some information about single Remote Station. - if they are set up but not available - if they are responding - if there are parity errors RS -test

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

17/ 35

TCB

Date:

17-Aug-2009

16

RSL -address

A a

available (IO-No. is defined) not available

R r

responding (Hardware is okay) not responding

000

parity error counter

Key GOON / Shift Key GOBACK: Skip through the list of Remote Stations which signals - not available or - not responding or - parity errors. If there was at least one entry in the list, the display for Test not successfully finished (-) occurs.

PR +

EE + RA + RS 48Ar000

PR +

EE + RS -

RA +

Key Clear: Back to Test –Menu. 3.3.3

SETUP –Function ( <1> <3>)

System = 1 Setup = 3 In the following all the SETUP –functions are explained. The Install-, RSL-, Allowed-, POS- and ELD- functions are used to set the parameters and masks of the EEPROM where the DCS Run function has the task to check if every open door opens the safety chain. There are four different groups of Setup Parameters to define the elevator environment: - Installation Parameters - RSL – IO Numbers - Allowed Masks - Position Indicator Parameters - ELD - Display The DCS – Function is used to test the well installed Door safety chain after startup and setup phase.

3.3.3.1 Install –Function ( <1> <3> <1>) Install = 1

Short Key S4

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

18/ 35

TCB

Date:

17-Aug-2009

System = 1 OCSS = 2 : Security = 9 Test with Install – Menu 01 System

Function Install is used to set Installation Parameters. The parameters are divided into 8 groups. The Install Menu gives access to each group.

>

000 System new TOP = 004>

1)

The range of each parameter is defined and controlled by software. The storage operation is disabled if the car is moving. (see document: List of Installation Parameters)

2)

Element-No. / Group / Name

000 System new TOP = 004> 3)

1) 000 2) System 3) TOP

element-No. of group current group name name of current Install Parameter

Key GOON / Shift Key GOBACK: Skips through the assigned group of Installation Parameter. Key CLEAR: Back to Install - Menu Enter a new parameter 000 System new TOP = 004> 1)

Input: Install Parameter 1) 2)

004 000

current value of Install Parameter input field for new parameter

2)

Key 3,2: Input keys of the new parameter (32) Key CLEAR: Deletes the last input if you want to correct the number

Shift Key ENTER: Termination to store the new Install Parameter into the EEPROM 3.3.3.2 RSL –Function ( <1> <3> <2>) RSL = 2

Short Key S5

000 System TOP = 004>032 000 System TOP = 004>003

new

new

000 System new TOP = 003>

OTIS


FOD BERLIN

I AD P

AD P

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


IO >

Part:

Service Tool Manual

Page:

19/ 35

TCB

Date:

17-Aug-2009

The arrow is pointing to the input field of the IO-Number. After you entered the IO-Number the current RSL information stored in the EEPROM is displayed. Now you can change the RSL-Address and the RSL-Plug. The Invert Bit can not be changed. It is set by software. For RSL-Address 0 up to 4 it is always set to zero. ( see document: List of Inputs and Outputs)

Key 2,2,2: Input Keys of the desired IO-Number (222)

IO I AD P AD P >0222

Key CLEAR: Deletes the last input if you want to correct the number IO I AD P AD P 0222=0 57 2>

Shift Key ENTER: Termination of the IO-Number input The current information stored in the EEPROM is displayed: IO: IO – Number AD: Remote Station – Address I: Invert Bit P: Remote Station - Plug Note:

Once a IO-number is defined, it is stored in the system!

Key CLEAR: Clears the display to enter a new IO-number.

IO >

I AD P AD P

Change the IO - Number Key GOON / Shift Key GOBACK: Skip to the next / previous IO – number. Shift Key UP / Shift Key DOWN: Skip to the next / previous IO-number with defined RSL-Addr. And RSL-Pin/Plug. Enter new RSL – Parameter 1) 2) IO I AD P AD P 0032=0 04 2> Key 0,4,2: Input Keys of

Input: RSL - Parameter 1) 2)

AD P

RS-Addr.: 04 and RS-Pin: 2

Shift Key ENTER: Termination of the RSL-Parameter input operation.

new RSL-Address new RSL-Pin/Plug IO I AD P AD P 0032=0 57 2> 04 2

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

20/ 35

TCB

Date:

17-Aug-2009

Key CLEAR: Deletes the last input if you want to correct the number. Setup inverted I/O After entering an I/O-number the following display will be shown: 1

9

...

IO I AD P AD P 0001=1 16 3>

1:

0: normal signal 1: inverted signal 16 3: RSL address

alternating display IO inverted IO! 0001=1 16 3>

< 1 > ... < 9 > < ON > < ENTER > Note:

Enter two digits to enter a emote Station address and a pin number. Use ON to toggle the type of the remote signal (inverted / not inverted) Press ENTER to store the changed value.

To invert an already programmed IO the shown address must be entered again!

3.3.3.3 Allowed – Function ( <1> <3> <3>) Allowed = 3 Enable = 1 Cut Call = 2 Card Reader = 3 ALLOWED – Menu 01 Enable at CUDE CUDE P R 00 1100 0000 0 0

Function Allowed is used to set the Floor Table Masks. The masks are divided into 3 groups: - Enable - Cut Call - Card Reader. The Allowed Menu gives access to each group.

Enable Display ( <1> <3> <3> <1>) 1) 2) 3) 4) 5) Enable Display

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

at CUDE CUDE P R 00 1100 0000 0 0

Service Tool Manual

Page:

21/ 35

TCB

Date:

17-Aug-2009

1) at

level number (0)

2) CUDE 3) CUDE - C - U - D - E

front door Enable Mask and rear door Enable Mask, with: - Car Call - Up Hall Call - Down Hall Call - Emergency Hospital Call (1 = allowed / 0 = not allowed)

4) P

Parking Bit: (1 = not allowed / 0 = allowed)

5) R

Reduced Landing No.: - Short Run (1,2,3 = profile) - Medium Run (4,5,6 = profile)

The Enable Masks (CUDE) allows the Elevator to run to a certain level depending on the regarding call. If the Parking Bit is set to 1, parking at a certain level is not allowed (Group application). The Reduced Landing No. indicates that the above floor is a Short- or Medium- Landing. The velocity (profile) is a function of the number (1,2,3 or 4,5,6). 3.3.3.3.1 Cut Call Display ( <1> <3> <3> <2>) 1)

2)

3)

at CUDE CUDE 00 1100 0000

4) OP 0

Cut Call Display 1)

at

level number (0)

2) 3)

CUDE CUDE - C - U - D - E

front door Cut Call Mask and rear door Cut Call Mask, with: - Car Call - Up Hall Call - Down Hall Call - Emergency Hospital Call (1 = allowed / 0 = not allowed)

4)

Op

Parking with door open 0 = both doors closed 1 = only front door open 2 = only rear door open 3 = both doors open

The Cut_Call Masks (CUDE) are used to supress the Enable Mask if a Cut_Call Signal (CHCS) occurs. The indication Parking with door open defines the door state during parking.

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

22/ 35

TCB

Date:

17-Aug-2009

3.3.3.3.2 Card_Reader Display ( <1> <3> <3> <3>) 1) 2) 3) 4) Card_Rd Display at CUDE CUDE 00 1100 0000

Sb 0

1)

at

level number (0)

2) 3)

CUDE CUDE - C - U - D - E

front door Card_Rd Masks and rear door Card_Rd Masks, with: - Car Call - Up Hall Call - Down Hall Call - Emergency Hospital Call (1 = allowed / 0 = not allowed)

4)

Sb

Special door open button 0 = both SDOB disabled 1 = only front SDOB enabled 2 = only rear SDOB enabled 3 = both SDOB enabled

The Card_Rd Masks (CUDE) are used to reach certain floors with magnetic card (Card Reader Operation). The indication Special door open button defines the operation of the Special Door Open Button. Change the level Key GOON / Shift Key GOBACK: Skip to the next level number

at CUDE CUDE P R 00 1100 0000 0 0

Key CLEAR: Back to Allowed Menu Enter new Allowed – Parameter Key 0,1,0,...: Input Keys of all the numbers (10) of the current row.

at CUDE CUDE P R 00 1100 0000 0 0

Key CLEAR: Deletes the last input if you want to correct the number. Shift Key ENTER: Termination of the Allowed Parameter input operation.

3.3.3.3.3 Openings and Dummy Doors at CUDE CUDE P R 00 1100 0000 0 0

For the controller with TCB Openings and Dummy Doors are defined as follows:

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

23/ 35

TCB

Date:

17-Aug-2009



The Openings are determined by Software regarding to the Level Arrangement done with Function Allowed-Enable and the following Rule. Important! Count the Front- and Rear Doors for each Level beginning at Level 0 / Frontside.



A Dummy door is an option to define the same Level Arrangement for every elevator in Group applications. at F: 00 R: -00 1100 0000

P R 0 0

Key 2,0,0,0...: Input Keys of all the numbers of the current row (level 1) 2000 is the Code for a Dummy Door.

at F: 01 R: -01>2000

P R

Shift Key ENTER: Termination of the Allowed-Parameter input operation. The new determined Openings are displayed.

at F: 01 R: 02 01 2000 1110

P R 0 0

Shift Key UP: < toggle key > Display of the determined Openings. F: 00 R: --

at Front Door of Level 0: Opening 0 at Rear Door of Level 0: no Opening

F: 01 R: 02

at Front Door of Level 1: Opening 1 at Rear Door of Level 2: Opening 2

3.3.3.4 POS – Function ( <1> <3> <4>) POS = 4 Pos.Ind. at: L 00 = 10

Function POS is used to set the digits of the Position Indicator. For each level a left (L) and a right (R) digit is provided to indicate the floor. The range of each digit is defined in the table below.

new >

Input: POS digits

Pos.Ind. new at: L 00 = 10 > 1)

2)

3)

1)

L R

left digit right digit

2)

00

level number (00)

3)

10

current value of Pos.Ind. digit (10 = blank)

4)

new

input field for new value

4)

Key GOON / Shift Key GOBACK: Skip first to the next / previous digit and then to the next / previous level.

Pos.Ind. new at: R 00 = 00 >

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

24/ 35

TCB

Date:

17-Aug-2009

Key CLEAR: Back to Setup-Menu. Enter a new digit Key 1,5: Input Keys of the desired digit (15 = E) (see Reference List below)

Pos.Ind. new at: R 00 = 10 > 15

Key CLEAR: Deletes the last input if you want to correct the number. Shift Key ENTER: Termination of the input operation. The current information stored in the EEPROM is diplayed:

Pos.Ind. new at: R 00 = 15 >

Reference List Value Symbol Value 0 0 10 1 1 11 2 2 12 3 3 13 4 4 14 5 5 15 6 6 16 7 7 17 8 8 18 9 9 19 (* for 16-segment only!)

Symbol (blank) A B* C D* E F G* H I*

Value 20 21 22 23 24 25 26 27 28 29

Symbol J* K* L M* N* O P Q* R* S

Value 30 31 32 33 354 35 36 37

Symbol T* U V* W* X* Y* Z* -

3.3.3.5 Door Check Sequence ( <1> <3> <5>) DCS = 5 The Door Check Sequence (DCS) –Function is a safety feature for OTIS2000 MRL. It insures that all hoistway door contacts are installed correctly and will open the safety chain, if a door opens. Until the Door Check Sequence is finished successfully it is only possible to move the car in inspection mode. Normal runs are disabled. The calibration menu appears in following case: OVFWW EN-ADO = 0 EN-RLV = 0 Allow Normal Start DCS

=0 =1

Key 0: From now 10 normal runs are allowed to calibrate the drive package. Key 1: Start the DCS-run immediately.

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

25/ 35

TCB

Date:

17-Aug-2009

Otherwise it is possible to enter commands for runs in normal mode to Top or Bottom landing if you push the CCTL- or CCBL- button on the SBP. After selecting ”0” the following message is displayed until the max number of runs have been completed: Now calibrate Drive package!

Key CLEAR: jump back to previous menu to start DCS-run

Note: If the number of runs are not done within a specific time then the previous menu is displayed and ”0” has to be pressed again to allow further calibration runs. Starting the Door Check Sequence Before you can start the DCS-run the start conditions have to be checked. If any condition is not fulfilled an error message is displayed. DCS Start Error Setup C-Type:

Error Message

Error Reason

Setup C-Type: C-Type not 2 or 3 Not able to run! OCSS mode is NAV Switch of INS! OCSS mode is INS Already done DCS already performed Into 1LS and DZ! Car is not in 1LS and DZ Leave 1LS Car in 1LS but not DZ If no start error is detected you can start the DCS-run by pressing ENTER. to start DCS press ENTER

Key ENTER: Start the automatic DCS run.

The automatically performed DCS-run can be followed on the SVT display. Direction - 00 DW: clsd ][ ][ open front door

U D Position

- 00 DW: clsd ][ ][ open front door

00 **

DW status - 00 DW: clsd ][ ][ open front door

DW: clsd dw: opnd

Description stop / direction not defined car is moving in UP direction car is moving in DOWN direction Description actual level (level 0) level position not defined

Description DW active (switch closed, door closed) DW passive (switch opend, door opend)

OTIS


GBA 26800BA IV

Page:

26/ 35

TCB

Date:

17-Aug-2009

][ ][

Description front / rear door state: ] [ for Closed ] [ for Open <> for Opening >< for Closing * * for door state not defined

Door action - 00 DW: clsd ][ ][ open front door

No.:

Service Tool Manual

Doors states - 00 DW: clsd ][ ][ open front door

4 - AA3

Vintage: 01 / 1


FOD BERLIN

Part:

Open front door Check DW input Close front door Open rear door Close rear door Up to next level

Description (listed are the current actions of the automatic DCS-run)

If a failure occurred the error is displayed in the 2 nd row. The 1st row shows the status including the level number where the error was detected: Error message - 00 DW: clsd ][ ][ Front Door Error

Description

Front Door Error (listed are the possible error messages Rear Door Error of the automatic DCS-run) Aborted by ENTER Door opening err DW not closed Position error Door closing Err

After successful completion of the DCS-run the success message is displayed. DCS successfull press GOON > Check PES, GTC ... press GOON > to start normal press GOON >

(as reminder what has to be done next)

(to leave DCS-run)

3.3.3.6 ELD – Function ( <1> <3> <6>) ELD = 6

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

27/ 35

TCB

Date:

17-Aug-2009

The ELD – function is used to define the ”Customer Message” of the OTIS 2000 –ELD. For each floor the Customer Message can be  displayed (Floor Display)  modified (Edit Display and Default Display)  or stored into EEPROM (Store Display). 1)

2)

Floor Display

00
1) 00 2) ALL

3) send to ELD  

3) 4)

5)

Edit Display

00 T< ALL ELD BASEMEN?

4) T 5) T

 

confirm the storage operation with Key



00 00ENG LOBBY

selected character selected string position

Store Display

00 write E2P? BASEMENT   6)

level number Edit-Mode: ALL: all characters available A-Z: only A – Z 0-9: only 0 – 9 &/): only &(), -. / :<>’ SPE: only Ä Á Å Ç  Ö Æ HEX: all characters available by using hex input mov: move the string to left or to the right current Customer Message: BASEMENT

7)

Default Display 6) 00 7) ENG

8)

No. of Default Message select Language ENG English GER German ITA Italian

8)

selected Default Message (see Reference Table below)

Floor Display: Select Floor and Edit Mode 00
OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Part:

Service Tool Manual

Page:

28/ 35

TCB

Date:

17-Aug-2009

Key 0-9, GOON, GOBACK: Selects, decreases or increases the Floor Number (level). The current Customer Message which is stored in the EEPROM will be displayed on the Service Tool.

01
Key UP/DOWN: Selects the Edit-Mode, which will be used in edit-Display.

01
Key ENTER: Transition to Edit-Display.

01 1< FLOOR ?

A-Z
Key CLEAR: Back to Setup-Menu. Modified Messages will be sent to the ELD – Module. Edit-Display: Modify Customer Message 00 T< ALL
00 N< ALL ELD BASEME?T

00 O< ALL ELD BASEME?T

Key 1-9: Skips through the character set using the selected step width. (Key-No.) Key ENTER: Transition to Store Display to store the string into EEPROM. Key ON: Transition to Default Display to use predefined Customer Messages. (see Reference Table below)

00 00 ENG LOBBY

Key CLEAR: Back to Floor Display e.g. to change the Edit-Mode. The current Message will be buffered. Edit Modes HEX and mov HEX Display 1) 2) HEX Display 00 Y<59 HEX ENG LOBB?

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

29/ 35

TCB

Date:

17-Aug-2009

1) Y 2) 59 3) 3)

Edit – Field HEX – Field: Displays the HEX-Value of the selected character selected character (Y?)

Key UP/DOWN: Selects the string position you want to modify. Key GOON/GOBACK: Skips through the character set of Edit-Mode ALL to select the new character. Key 0...F: Input of 2 digits Hex-Code in HEX-Field to define the new character (see Reference Table below). mov Display 00 GOON> LOBBY

ELD

Key GOON/GOBACK: The displayed message will be shifted to the right/left. It is a easy way to centre the message on the ELD. Default Display: Use of predefined messages 00 00 ENG LOBBY Key UP/DOWN: Selects the language of the Default Message (ENG, GER, ITA) Key GOON/GOBACK: Skips through the Default Message List (see Reference Table below). Key 0-9: Two digits input to select the Default Message by entering the List-No. (see Reference Table below. Key ENTER: Transition back to Edit display. The desired Default Message will be bufferd. Key CLEAR, OFF: Back to Edit Display without buffering the changes. Reference Tables for ELD – Function Default Messages

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Part:

ENG LOBBY BASEMENT PENTHOUSE FLOOR RECEPTION EXIT GARAGE SECRETARY RESTAURANT CAFETERIA GARAGE POOL SAUNA DOCTOR 0 123 456 789 : . () <> / -, & ’ ABCD EFGH IJKL MNOP QRST UVWXYZ ÄÁÅÇØ Ö Æ empty string

Service Tool Manual

Page:

30/ 35

TCB

Date:

17-Aug-2009

GER ERDGESCHOSS KELLER DACHTERASSE ETAGE EMPFANG AUSGANG TIEFGARAGE SEKTRETARIAT RESTAURANT KAFFEESTUBE PARKHAUS SCHWIMMHALLE SAUNA ARZT 0 123 456 789 : . () <> / - , & ‘ ABCD EFGH IJKL MNOP QRST UVWXYZ ÄÁÅÇØ Ö Æ

ITA TERRANO SOTTERRANEO ATTICO PIANO RICEZIONE USCITA POSTEGGIO SEGRETERIA RISTORANTE CAFFETERIA POSTEGGIO PISCINA SAUNA DOTTORE 0 123 456 789 : . () <> / - , & ‘ ABCD EFGH IJKL MNOP QRST UVWXYZ ÄÁÅÇØ Ö Æ

HEX-CODE Table ASCII Blank & ( ) , . / : < >

3.4

HEX 20 26 28 29 2C 2D 2E 2F 2A 3C 3E

ASCII 0 1 2 3 4 5 6 7 8 9

HEX 30 31 32 33 34 35 36 37 38 39

ASCII A B C D E F G H I J K L M

HEX 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D

ASCII N O P Q R S T U V W X Y Z

TOOLS – Function ( <2>)

In the following all the TOOLS – functions are explained.

HEX 4E 4F 50 51 52 53 54 55 56 57 58 59 5A

ASCII Ä Á Å Ç A-E Ø Ö

HEX 80 81 82 83 84 85 86 87

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

31/ 35

TCB

Date:

17-Aug-2009

It is a list of 5 functions that makes the installation, debugging and maintenance of the elevator easier. 3.4.1

Search-IO – Function ( <2> <1>)

TOOLS-Menu = 2 Search-IO =1 Search-IO Adr: 00 / Pin:

? 0

Function Search-IO displays which IO-numbers are assigned To a certain RSL-address / pin. After input of Adr. and Pin and termination with ENTER the Search run begins and will be indicated with the change of: (?)  (!). The find of an IO-number interrupts the Search Run and the number is displayed. ENTER will continue the Search Run. Enter Adr. And Pin Key 1,5,3: Input Keys of RSL-Adr. and Pin.

Adr:

Search-IO 15 / Pin:

? 3

Adr:

Search-IO 15 / Pin:

! 3

Key CLEAR: Deletes the last input for correction. Shift Key ENTER: Termination of the input operation and start of The Search Run. Possible Results: a) no IO-number found

b) first IO-number found

Search-IO no match ! Search-IO ? > 15 3 < IO: 0676

Now you can continue the Search run with ENTER. It is also possible to edit the Adr./Pin display >15 3<.

Shift Key ENTER: Continue the Search Run If you want to edit the Pin Number press: - Key CLEAR, to delete the last input - Key 4, to enter the new pin - Shift Key ENTER, to continue the Search Run. If there is no more IO-number defined, the no more match! –display comes up.

Search-IO ! > 15 3 < IO: 0676

Search-IO ? > 15 4 < IO: 0676 Search-IO ! > 15 4 < IO: 0676

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

32/ 35

TCB

Date:

17-Aug-2009

- Key CLEAR: Back to TOOLS – Menu. 3.4.2

Erase-IO – Function ( <2> <2>)

Erase IO = 2 Erase IO Part ? n=0 y=1 / Enter

Function Erase IO Part can be used to set the IO-Part of the EEPROM to default. You have to confirm twice to start the function, because after the run all the previous definitions are lost! (see document: List of Inputs and Outputs)

Key Clear: back to TOOLS – Menu Key 0 and Shift Key ENTER: back to TOOLS – Menu Erase IO Part ? n=0 y=1 / Enter

Key 1 and Shift Key ENTER: First confirmation Key 0 and Shift Key ENTER: back to TOOLS – Menu Key 2 and Shift Key ENTER: Second confirmation to start the function.

Erase IO Part ? n=0 y=2 / Enter

During run the displayed counter is counting down to zero. 3.4.3

Setup Install – Function ( <2> <3>)

Setup INST = 3 Setup Install ? n=0 y=1 / Enter

Function Setup Install can be used to set the IO-Part of the EEPROM to default. You have to confirm twice to start the function, because after the run all the previous definitions are lost! (see document: List of Install. Parameter)

Key CLEAR: back to TOOLS – Menu Key 0 and Shift Key ENTER: back to TOOLS - Menu

Key 1 and Shift Key ENTER: First confirmation

Setup Install ? n=0 y=1 / Enter

Key 0 and Shift Key ENTER: back to TOOLS - Menu Key 2 and Shift Key ENTER: Second confirmation to start the function. During run the displayed counter is counting down to zero.

Setup Install ? n=0 y=2 / Enter Setup Install ! Please Wait: 15

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN 3.4.4

Part:

Service Tool Manual

Page:

33/ 35

TCB

Date:

17-Aug-2009

Setup Door – Function ( <2> <4>)

Setup Doors = 4 This function can be used to preset the parameters for the Generic Door Operator so that the door operation is the same as with normal door setup.

Which door type ? Front >

Afterwards you just need to change some parameters to Modify the operation without having to setup all Generic Door Parameters. Key 1 – 9: Select the door type which should be programmed into the Generic Door parameters. The meaning of the numbers is the same as for the parameters ”DOOR” and ”REAR”. After pressing ENTER you will be asked to select the rear door type. Press ENTER again to preset the rear door parameters In the same manner.

Which door type ? rear >

The following list shows which values are used for the Generic Door parameters: Door type 0 1 2 3 4 5 6 7 8 9 10 Note 1)

3.4.5

Name FLH 9550 & ACG 9550 & TLD/CLD OVL / MRDS OVL & ACG DO2000 MCG Kiekert & ACG Kiekert & TLD OVL-Penang & ACG OVL-Penang & TLD/CLD

DO-TYP 10 1) 10 10 11 11 11 10 1) 11 11 11 11

DC-TYP 10 1) 10 10 11 11 0 10 1) 10 10 11 11

EN-ACG 0 1 0 0 0 0 1 1 0 1 0

DO-D 10 0 0 0 0 0 40 40 40 0 0

CM-TYP 11 11 0 0 0 0 11 11 0 11 0

These values are set for compatibility reasons because some contract-modified controllers have additional relays connected to the DO- and DC-relays. In normal cases the parameters DO-TYP and DC-TYP can be set manually to 0. Operate Memory ( <2> <9>)

Opr. Memory = 9 Function Operate Memory can be used to monitor and change the memory. (You can only change the RAM.) To enter hexadecimal numbers the Hex Keys are available. The Short Keys are not active. Please notice that the Operate Memory function is provided only for software debugging. Hex Keys

No.

Shift Keys

Hex Keys

OTIS


4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

A – 00 IDL ST 00000

Part:

Service Tool Manual

Page:

34/ 35

TCB

Date:

17-Aug-2009

0 1 2 3

-

OFF ON UP DOWN

4 5 6 7 8 9

-

DISP IN SEL OUT DISP STATE ENT CALL TEST

-

A B C D E F

The first row displays the Software Status. The second row displays the input field for the desired Memory Address. After the address is entered, the next two bytes of memory are displayed. Please notice that PLM-words are stored in the order: LOW-byte / HIGH-byte. ][ ][

Enter the memory address A – 00 IDL ST 0002D

Key 2, Shift Key 7: Input Keys of the desired Memory Address (2D Hex)

][ ][

Key CLEAR: deletes the last input if you want to correct the number A – 00 IDL ST 0002D: 2134

Shift Key ENTER: Termination of the input operation.

1) A – 00 IDL ST 0002D: 2134 low byte of word at address 0002D

2)

][ ][

Operate Memory: Monitor

][ ][

1) 0002D

desired memory address (2D Hex)

2) 2134

memory contents of address 2D and 2E

high byte of word at address 0002E

Change the memory address Key GOON / Shift Key GOBACK: Skip to the next / previous memory address (last four digits).

A – 00 IDL ST 0002E: 43BA

][ ][

Shift Key UP / Shift Key DOWN: Skip to the next / previous address in steps of 10000hex

A – 00 IDL ST 1002E: 5B7D

][ ][

OTIS


Part:

4 - AA3

No.:

GBA 26800BA IV

Vintage: 01 / 1


FOD BERLIN

Service Tool Manual

Page:

35/ 35

TCB

Date:

17-Aug-2009

Change the memory contents Shift Key SELECT: ”>” indicates the input field ”- - - -” are placeholders for the up to four digits of the new byte resp. two bytes.

A – 00 IDL ST ] [ ] [ 0002D: ABCD > - - - -

Depending on how many digits are entered the first byte or both bytes are stored. The first up to two digits of the first byte and the next up to two digits of the second byte. Examples of changing the old contents ABCD: Keys ENTER 1, ENTER 1, 2, ENTER 1, 2, 3, ENTER 1, 2, 3, 4, ENTER

Display - - - - 1- 12- 12–3 1234

New memory contents ABCD 01CD 12CD 1203 1234

Key GOON / Shift Key GOBACK: Aborts changing of memory contents.

A – 00 IDL ST 0002D: ABCD

Key ENTER: Storing the new byte resp. two bytes. A short appearing ”+” behind the entered byte Resp. two bytes acknowledges the successful storing. A ”-” indicates a storing failure (e. g. memory address is out of RAM area).

A – 00 IDL ST ] [ ] [ 0002D: ABCD>12-3+ A – 00 IDL ST 0002D: 1203

][ ][

][ ][

Otis TCB Svt

Recommend Documents