Piping Material Management - Herve Baron

Piping Material Management

3D model

Piping Material Management Software

© 2 0 1 6

H –

Piping Material Classes 

Step 1: Process produces the Fluids list with •

Fluid(s) services,

•

Service conditions (range of temprature and pressure)

•

Basic material,

•

Corrosion allowance,

© 2 0 1 6

H –


Step 1: Process produces the Fluids list with •

Fluid(s) services,

•

Service conditions (range of temprature and pressure)

•

Basic material,

•

Corrosion allowance,

© 2 0 1 6

H –


Step 2: Process groups the Fluids in Piping classes of same material and range of service conditions

© 2 0 1 6

H –


Step 3: Piping produces the Piping Classes Summary with •

Definition of type of valve (gate, globe , check, ball , butterfly, …),

•

Definition of trims of valves,

•

Definition of kind of gasket,

•

Definition of bolting quality,

•

The others requirements (corrosion, heat treatments, …),

© 2 0 1 6

H –


Step 4: Piping produces the specification for each Piping Class

© 2 0 1 6

H –

Piping material class specification Each item is defined by a Material Standard and a Dimensional standard

© 2 0 1 6

H –

Piping material class specification Each item is defined by a Material Standard and a Dimensional standard

© 2 0 1 6

H –

Piping material class specification The wall thickness of pipes, elbows and tees must be calculated as per the applicable design code, for oil & gas facilities, ASME B31.3

© 2 0 1 6

H –

Piping wall thickness calculation ASME B 31.3

t

P*D (2SWE



PY)

© 2 0 1 6

H –

Piping material class specification Flanges shall be selected for the design P, T limit of the material

© 2 0 1 6

H –

Piping material class specification Design & construction code, types and materials of seat/seal, trim, are specified for valves

© 2 0 1 6

H –

Piping material class specification 

Once the Piping Material Classes are defined, they are entered into the Piping Material Management Software

Piping Material Management Software © 2 0 1 6

H –


Each component is codified « smartly » with Commodity Code Example: Commodity Code (welding neck flange) Table Name:

Group: Part: A-Dimensional Std: B-Material: D-Ends: F-Rating: X-Alias:

Commodity code:

Table Detail

Digits

Flanges Welding neck flange ASME B 16-5 ASTM A105 R.F. 150 lbs Ra=3.2 to 6.3µm

1 2 1 4 2 2 2

FWN1C54X12L201

Code

F WN 1 C54X 12 L2 01

© 2 0 1 6

H –


The piping classes are loaded from the Piping Materials Management software into the 3D model

Piping Material Management Software

3D model © 2 0 1 6

H –

Piping material requisition Now let’s see what are the time requirements to order Piping materials.

© 2 0 1 6

H –

Piping material requisition Let’s consider a lareg 3-year Project. Piping material is usually required at Site on month 18. When shall it be ordered latest?

© 2 0 1 6

H –

Piping material requisition Piping material is required at Site on month 18. When shall it be ordered latest? Required On Site (ROS) date - procurement cycle - transport duration = required Engineering requisition issue date

© 2 0 1 6

H –

Piping material requisition Piping material is required at Site on month 18. When shall it be ordered latest? Required On Site (ROS) date - procurement cycle - transport duration = required Engineering requisition issue date

Inquiry to PO

4 months

PO to ex-works

Pipes 6-8 months Fittings & flanges 8 months

Transport, incl. Custom clearance 2 months ======================================================== POs to be placed month 18 2 8 = month 8 of the 3 year Project!

© 2 0 1 6

H –

Piping material requisition PROJECT MONTH

4 INQUIRY

Inquiries issued

18

8 MANUFACTURING

Purchase orders placed

TRANSPORT

Material Site delivery

Piping fab. ©

Isometric

2 0 1 6

H –

Piping material requisition The Piping MTO is issued 3 times as a minimum: 1st MTO: issued for Inquiry, to get the Unit prices  2nd MTO: issued for Order  3rd and subsequent MTOs: to top-up 

On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared?

© 2 0 1 6

H –


On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared? 

1st MTO:

© 2 0 1 6

H –


On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared? 

1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)

© 2 0 1 6

H –


On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared? 1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)  2nd MTO 

© 2 0 1 6

H –


On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared? 1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)  2nd MTO: IFD P&IDs + Piping studies/layouts or 3D model (part) 

©

How are Quantities to purchase (BOM) obtained from the MTO quantities?

2 0 1 6

H –

Material Take-Off’s Piping material Piping specifications

Piping installation

MTO quantities - Uncertain items

P&IDs MTO Piping routing / layout

+ Allowances for cut & losses + Estimates of what is not taken-off + Allowances for

Bill of Materials

Material Requisition

© 2 0 1 6

H –

Material Take-Off’s 1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)  2nd MTO: IFD P&IDs + Piping studies/layouts or 3D model (part) 

100 90 ) % ( s e i t i t n a u q

80 70

Estimation

60

Validity factor

50

Manual take-off

40

Model 3D

30 20 10

© 2 0 1 6

H –


On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared? 1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)  2nd MTO: IFD P&IDs + Piping studies/layouts or 3D model (part)  3rd and subsequent MTOs 

© 2 0 1 6

H –


On the basis of which document(s) are the 1 st, 2nd and 3rd piping MTO prepared? 1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)  2nd MTO: IFD P&IDs + Piping studies/layouts or 3D model (part)  3rd and subsequent MTOs: (IFC P&IDs) + isometrics (3D model) 

© 2 0 1 6

H –

Piping Material Management Above ground Piping

P&ID Piping Material Take-Off’s

Drawing

IFR

IFD

1st MTO (for inquiry)

Piping routing

IFC 2nd MTO (for order)

Piping layout drawings/3D

3rd MTO (top-up’s)

Piping isometric

© 2 0 1 6

H –

Piping Material Management Isometric

Once the isometric is issued the final list of material is known.

3D

© 2 0 1 6

H –


These quantities are fed into the Piping Material Management software.

3D Piping Material Management Software © 2 0 1 6

H –


They replace the previous quantities (that of MTO 2).

3D

© 2 0 1 6

H –


The difference is made and balance quantities are ordered.

3D

© 2 0 1 6

H –

Piping material requisition 1st MTO: P&IDs 1st issue + Plot Plan or Line diagram (if available)  2nd MTO: IFD P&IDs + Piping studies/layouts or 3D model (part)  3rd and subsequent MTOs: (IFC P&IDs) + isometrics (3D model) 

100 90 80 ) % ( s e i t i t n a u q

70 60 50 40 30 20 10

Model 3D IFC Estimation Validity factor Manual take-off Model 3D © 2 0 1 6

H –

Piping Material Matching What is Piping Material matching?

© 2 0 1 6

H –

Piping Material Matching What is Piping Material matching? A check to know if all materials required to fabricate a piping iso/spool are available at Site. In the positive the spool is called a « Yes » spool .

© 2 0 1 6

H –

Piping Material Matching Bill of materials

Shop isometric Material match?

© 2 0 1 6

H –


Shop isometric

« No » spool

Material match?

© 2 0 1 6

H –


50% Shop isometric

75% « No » spool

Material match?

˜ 33%

© 2 0 1 6

H –

Piping Material Matching What is Piping Material matching? A check to know if all materials required to fabricate a piping iso/spool are available at Site. In the positive the iso/spool is called a « Yes » iso/spool. It enables you to assess the workfront.

© 2 0 1 6

H –

Piping Material Matching What is Piping Material matching? A check to know if all materials required to fabricate a piping iso/spool are available at Site. In the positive the iso/spool is called a « Yes » iso/spool. It enables you to assess the workfront. To do the material matching you must allocate the BOM of the iso/spool to the materials in the Piping Material Management System. This is done by feeding the BOM with the iso/spool reference in the Piping Materials Management system. © 2 0 1 6

H –

Piping Material Management System

Piping Materials Procurement Material requisition Piping Design

Legend Activity

Document

Design/shop iso © 2 0 1 6

H –

Piping Material Matching What is Piping Material matching? The Piping Material Management System is fed with the materials deliveries.

© 2 0 1 6

H –

Piping Material Management System Site Materials receipt Piping Materials Procurement Material requisition Piping Design

Legend Activity

Document

Design/shop iso © 2 0 1 6

H –

Piping Material Matching What is Piping Material matching? This enables the Material Matching!

© 2 0 1 6

H –

Piping Material Management - Herve Baron

Recommend Documents