Thunder-Link.com is a Leading Huawei optical transmission product supplier. Which was founded by ex-Huawei employee, we have rich experience and well reputation in the field over 3 years.
citransFull description
Uputstvo za instalaciju lifta u stambenoj zgradi
Guide to install Mentum planet
sdhFull description
Accuver Drive test Analyzer Tool Quick QuideDescrição completa
Full description
Full description
NFC - NEAR FIELD COMMUNICATION INTRODUCTION ATTACK SURFACE
CAESAR II Quick Guide
PowerCube 1000 (ESS-H) Quick Installation Guide
Full description
BPMN Quick Reference Guide is compilation of the main structure of BPM application.Full description
System description for installationFull description
SAP MM guideFull description
Descripción completa
Bootstrap Quick Guide
Installing the RTN 310
2 1. 2. 3. 4. 5.
1+0 and DC Cover unused ports with caps. Different methods can be used to change the polarization direction of antennas. If the method described in this document is not suitable for the type of antenna you have, use the method described in the installation manual delivered with your antennas. The polarization direction of antennas is vertical by default. If the planned polarization direction is horizontal, change the polarization direction to horizontal. If an antenna with a diameter of 0.3 m or 0.6 m is used in a direct mount and 1+0 scenario, you may install the RTN 310 on the antenna and then hoist them both into position on the tower. If an antenna with a diameter larger than 0.6 m is used, hoist the antenna into position separately to avoid overloading the hoisting rope. Before installing a DC cable, bind the cable section that links the cable connector to the pole. This will protect the cable connector from damage. Be sure that the length of cable running from the binding point to the RTN 310 is sufficient to attach the cable connector to the PWR port on the RTN 310. Treat outdoor fibers in a similar manner to protect them from damage. Optional: Install the RTN 310 in split mount mode.
Optional: Install the RTN 310 on the antenna in direct mount mode.
1
Follow the antenna use instructions to install the antenna.
2
Optional: Change the polarization direction of the antenna to horizontal.
32
The RTN 310 can adapt its polarization direction to the antenna. There is no need to manually change the polarization direction. (For exceptions, see NOTE.)
4 5
1
Apply petroleum jelly around the exterior side of the feed. USB/
Install the RTN 310 on the antenna.
GE
P& E COMBO
USB RSSI
PW R
1
7 •
Install an outdoor fiber.
Connected to one GE (optical) service
•
Lay out the outdoor fiber. • Attach a yellow outdoor label to the fiber according to the plan.
8
10
Use the USB flash drive to load NE data.
Connected to the multimeter or Web LCT
Install an outdoor fiber.
Connected to the USB flash drive
11
Use the Web LCT to load NE data.
Install a DC cable.
Grounded through the ground clip Connected to the power supply device 9
Power on the RTN 310.
Mandatory The RTN 310s that have been delivered earlier may have polarizers and you need to turn the polarizers to change the RTN 310s' polarization direction. For details, see "Installation Reference."
•
Fix a split-mount installation bracket assembly to a pole.
Install the RTN 310 on the split-mount installation bracket assembly. •
12 Align antennas.
Optional
Follow the antenna use instructions to install the antenna. 22 Optional: Change the polarization direction of the antenna to horizontal. The RTN 310 can adapt its polarization direction 32 to the antenna. There is no need to manually change the polarization direction. (For exceptions, see NOTE.) 4 Apply petroleum jelly around the exterior side of the feed. 5 Install split-mount components. 1
Optional: connected to another GE (optical) service
•
Select a ground point for the DC cable. • Install the ground clip. • Lay out the DC cable. • Attach a matt white label to the cable.
Install the PGND cable of the RTN 310.
6
11
US SS B I//R R NS MSSI
• Install
a flexible waveguide.
13
Waterproof or corrosion-proof the outdoor connections of the DC cable, flexible waveguide, and ground clip.
