Schmitt Trigger
Schmitt Trigger Introduction In electronics, a Schmitt trigger is a comparator circuit that incorporates positive feedback. In the non-inverting configuration, when the input is higher than a certain chosen threshold, the output is high; when the input is below a different (lower) chosen threshold, the output is low; when the input is between the two, the output retains its value. The trigger is so named because the output retains its value until the input changes sufficiently to trigger a change. This dual threshold action is called hysteresis, and implies that the Schmitt trigger has some memory. In fact, the Schmitt trigger is a bistable multivibrator. Schmitt trigger devices are typically used in open loop configurations for noise immunity and closed loop positive feedback configurations co nfigurations to implement multivibrators. A comparator circuit, whether using an operational amplifier or some other electronics technology will work well under some conditions but it is not always ideal. If there is a slow waveform, or one with some noise ion it, then there is the possibility that the output will switch back and forth several times during the switch over phase as only small levels of noise on the input will cause the output o utput to change. This may not be a problem in some circumstances, but if the output from the operational amplifier comparator is being fed into fast logic circuitry, then it can often give rise to problems as the circuit will see several low high or high low transitions and will respond to each one. This can easily cause many problems. pro blems. Under these circumstances circuits that combat this problem are require. One known as the Schmitt trigger has been in use for many years, having been originally invented by an American scientist named Otto Schmitt. The Schmitt trigger switches at different voltages depending upon whether it is moving from low to high or o r high to low, employing employing what w hat is termed hysteresis.
WS Project Report
1
Schmitt Trigger
Invention The Schmitt trigger was invented by US scientist Otto H. Schmitt in 1934 while he was still a [1]
graduate student,
later described in his doctoral dissertation (1937) as a "thermionic trigger". It
was a direct result of Schmitt's study of the neural impulse propagat ion in squid nerves.
Symbol The symbol for Schmitt triggers in circuit diagrams is a triangle with an inverting or noninverting hysteresis symbol. The symbol depicts the co rresponding ideal hysteresis curve.
Standard Schmitt trigger
Inverting Schmitt trigger
Implementation A Schmitt trigger can be implemented with a simple tunnel diode, a diode with an "N"-shaped current±voltage characteristic in the first quadrant. An oscillating input will cause the diode to move from one rising leg of the "N" to the other and back again as the input crosses the rising and falling switching thresholds. However, the performance of this Schmitt trigger can be improved with transistor-based devices that make explicit use of positive feedback to implement the switching.
WS Project Report
2
Schmitt Trigger
Schmitt trigger circuit The problem can be solved very easily by adding some positive feedback to the operational amplifier or comparator circuit. This is provided by the addition of R3 in the circuit below and the circuit is known as a Schmitt trigger.
Operational Amplifier Schmitt Trigger Circuit
The effect of the new resistor (R3) is to give the circuit different switching thresholds dependent upon the output state of the comparator or operational amplifier. When the output of the comparator is high, this voltage is fed back to the non-inverting input of the operational amplifier of comparator. As a result the switching threshold becomes higher. When the output is switched in the opposite sense, the switching threshold is lowered. This gives the circuit what is termed hysteresis. The fact that the positive feedback applied within the circuit ensures that there is effectively a higher gain and hence the switching is faster. This is particularly useful when the input waveform may be slow. However a speed up capacitor can be applied within the Schmitt trigger circuit to increase the switching speed still further. By placing a capacitor across the positive feedback resistor R3, the gain can be increased during the changeover, making the switching
WS Project Report
3
Schmitt Trigger
even faster. This capacitor, known as a speed up capacitor may be anywhere between 10 and 100 pF dependent upon the circuit. It is quite easy to calculate the resistors needed in the Schmitt trigger circuit. The centre voltage about which the circuit should switch is determined by the potential divider chain consisting of R1 and R2. This should be chosen first. Then the feedback resistor R3 can be calculated. This will provide a level of hysteresis that is equal to the output swing of the circuit reduced by the potential divide formed as a result of R3 and the parallel combination of R1 and R2.
The effect of using a Schmitt trigger (B) instead of a comparator (A) WS Project Report
4
Schmitt Trigger
Practical
Schmitt Trigger Circuit
The output characteristic has exactly the same shape of the previous basic configuration, and the threshold values are the same as well. On the other hand, in the previous case, the output voltage was depending on the power supply, while now it is defined by the Zener diodes (which could also be replaced with a single double-anode Zener diode).
A Practical Schmitt Trigger Circuit
In this configuration, the output levels can be modified by appropriate choice of Zener diode, and these levels are resistant to power supply fluctuations (i.e., they increase the PSRR of the comparator). The resistor R3 is there to limit the current through the diodes, and the resistor R4 minimizes the input voltage offset caused by the comparator's input leakage currents. The value of the threshold T is given by, Also, the maximum value of the output M is the power supply rail. WS Project Report
5
Schmitt Trigger
Applications Schmitt triggers are typically used in open loop configurations for noise immunity and closed loop positive feedback configurations to implement multivibrators.
Noise immunity One application of a Schmitt trigger is to increase the noise immunity in a circuit with only a single input threshold. With only one input threshold, a noisy input signal near that threshold could cause the output to switch rapidly back and forth from noise alone. A noisy Schmitt Trigger input signal near one threshold can cause only one switch in output value, after which it would have to move beyond the other threshold in order to cause another switch. For example, in Fairchild Semiconductor's QSE15x family of infrared photosensors, an amplified infrared photodiode generates an electric signal that switches frequently between its absolute lowest value and its absolute highest value. This signal is then low-pass filtered to form a smooth signal that rises and falls corresponding to the relative amount of time the switching signal is on and off. That filtered output passes to the input of a Schmitt trigger. The net effect is that the output of the Schmitt trigger only passes from low to high after a received infrared signal excites the photodiode for longer than some known delay, and once the Schmitt trigger is high, it only moves low after the infrared signal ceases to excite the photodiode for longer than a similar known delay. Whereas the photodiode is prone to spurious switching due to noise from the environment, the delay added by the filter and Schmitt trigger ensures that the output only switches when there is certainly an input stimulating the device.
WS Project Report
6
Schmitt Trigger
Manufacturing Process: Primary
Stage:
Initially, Collect the circuit¶s name which is to be manufactured. Then, Collect the Circuit diagram & its required component of proper value.
Select which Circuit is to be manufactured
Collect its Circuit Diagram
Collect The Components of Desired Value
Second Stage: After the competition of primary stage, collect the copper clad, Draw the layout of circuit diagram, and Drill the points where the components are to mount & also drive & drill the testing points. After this go for the etching process. In the process, all the unwanted copper will be removed. Then, with the help of Digital Multimeter, check the continuity of all the tracks. If any track is discontinued with the help of metal wire & soldering gun, it can made continued.
Get The Copper Clad
WS Project Report
7
Schmitt Trigger
Draw The Layout of Circuit Diagram
Drill The Points Where Components Are to Mount
Etch The Copper Clad
Check The Continuity
If Any Discontinues, Solder It
Final Stage: After the PCB is get ready, tested components are mounted on the PCB. Cut the unwanted material of the component. Test the output of the component. Test the output of the circuit. At last, give the finishing touch to the circuit i.e. filling touch to the soldered points & again verify the Output.
Test The Components
WS Project Report
8
Schmitt Trigger
Solder The Components
Cut The Unwanted Material
Filing The Tips of Cut Components
Verif The Out ut
Circuit is Ready!
The End
Thank You!
WS Project Report
9