Atlas Copco Long-hole drilling rigs
Simba M7 C Technical specification
www.atlascopco.com
M7 C
M7 C
Illustration shows shows rig with optional optional equipment equipment mounted. mounted.
Long-hole drilling rig with tophammer rock drill. The Rig Control System (RCS) provides efficient and high precision drilling, longer consumable life and an ergonomic working environment. Ring drilling with parallel holes upwards/downwards up to 5.5 m apart. Hole diameter 51–89 (102) mm.
Standard features » Rock drill drill • Atlas Copco COP 1800-series • Dual-damping system for shock wave absorption and continuous rock contact for high penetration • Lubricated and pressurized mating surfaces providing longer service intervals • Shank adapters suitable for the given hole range
» Drilling Drilling unit • Mechnized rod handling system • Feed with hydraulic two-stage cylinder • Front- and rear-mounted stingers • Drill steel support for guidance during collaring and rod handling
»Positioning unit • Boom mounted drilling unit • Accurate, smooth and proportional movements • Mine-adapted, sturdy components
»Control system • Rig Control System (RCS) • Automation level: ABC Basic • Angle reading instrument • Rotation Pressure Controlled feed (RPCF) • Dampening Pressure Controlled Impact (DPCI) • Pre-set parameters for different drilling conditions • Anti-jamming system
»Carrier • Mine-adapted Mine-adapted carrier with articulated steering and four-wheel drive • Low-emission, turbo-charged diesel engine
»General • Operator panel mounted under canopy • FOPS-approved protective roof • Electrical cable reel • Working lights under protective roof
Simba M7 C
Specifications ROCK DRILL
»Electrical system
COP 1838ME Shank adapter Hole diameter Impact power Impact rate Hydraulic pressure, max. Rotation motors Rotation speed Lub. air consump. (at 3 bar) Water consumption Weight
R32, TC35, T38, T45 (TDS64) 51–89 (102) mm 18 kW 54 Hz 250 bar 07/09 0–210/0–140 rpm 8 l/s 100–250 l/min 171 kg
» Air system
FEED BMH 200-series
• Total installed power ................................................... 118 kW • Main motors ..............................................................2x55 kW • Voltage................................................................. 400–1,000 V • Frequency ................................................................. 50–60 Hz • Transformer ....................................................................8 kVA • Working lights mounted on roof .................... 35W, 24V HID • Electronic overload protection for electric motors • Digital volt/amperage meter in electric cabinet • Phase sequence indicator • Earth fault indicator • Battery charger • Cable reel
BMH 214
BMH 215
BMH 216
3,160 mm Total length 1,220 mm Drill rod length Total length with extractor 3,365 mm
3,465 mm 1,525 mm 3,670 mm
3,770 mm 1,830 mm 3,975 mm
• Screw-compressor ...................................... Atlas Copco GA 5 • Capacity at 5400 rpm and 7 bar ......................................20 l/s • Hydraulic driven axial piston motor .............................. 10 cc • Adjustable ow/pressure • Digital air pressure gauge • External air supply connection for hole blowing
» Drilling unit
» Water system
• Rod Handling System, RHS 17 ............................... 17+1 rods • Adaptable to R32,TC35, T38, T45 (TDS 64) drill rods • Adaptable to 4′, 5′ and 6′ rods • Mechanized drilling up to 32 m • Rock drill lubrication surveillance system
• Capacity at 15 bar boost ................................... max 250 l/min • Minimum water inlet pressure ........................................ 2 bar • Hydraulic drive, axial piston motor ............................... 10 cc • Hydraulic driven water booster pump • Digital water pressure gauge • Water ow/pressure guard
»Positioning system • Boom BUT 35BS (Ni-CR plated piston rods) • Feed extension (with 4′ drill steel) ............................. 900 mm • Feed extension (with 5′and 6′ drill steel) ................ 1,200 mm • Boom extension....................................................... 1,600 mm • Rotary acurator BHR 30 for 360º ring drilling • Stinger backward on feed ....................................... BSJ 8-200 • Stinger forward on feed .......................................... BSJ 8-115 • Feed dump, drilling ............. +90º forward and -10º backward • Rig alignment laser
»Control system • Rig Control System (RCS) – versatile and upgradeable to a higher degree of automation • Exposed components are designed and tested acc. to IP 65 • USB-memory stick for transfer of data and storage of drill parameters • Control panel mounted under canopy • Drill settings for up to ve different drill bits • Integrated diagnostic system • Angle reading instrument
» Power pack • System pressure, max .................................................. 250 bar • Hydraulic oil tank, volume max/min ....................... 250/200 l • Filtration, absolute......................................................... 16 μm • Oil temperature gauge with thermostat • Hydraulic pump for rotation, positioning, feed • Water cooled oil cooler in stainless steel • Low oil level indicator and shut-down • Smart oil leakage shut-down system • Hydraulic pump for percussion • Electric oil lling pump • Mineral hydraulic oil • Oil lter indicator
»Carrier • Engine .............................................. Deutz TCD 2013L04 2V • Power rating at 2,300 rpm ............................ 120 kW (163 hp) • Tramming speed on at ground ............................... >15 km/h • Tramming speed on incline 1:8 .................................. >5 km/h • Gradeability at max load on drive wheels.......................... 1:4 • Torque at 1,400 rpm ...................................................572 Nm • Hydrodynamic................................. Dana 24000 transmission • Articulated steering .................................. ±41° steering angle • Front axle ............................................. DANA Spicer 123/90 • Rear axle....................... DANA Spicer 123/90, ±8º oscillation • Tyres ........................................................................ 12.00 R24 • Clearence outside axles ...................................................... 15º • Hydraulic rear and front jacks............................................2x2 • Emergency and parking brakes .....................................SAHR • Fuel tank, volume.............................................................110 l • Electric system .................................................................24 V • Batteries......................................................... 2 x 125 Ah, 24V • Tramming lights ..............................................40W, 24V LED • Service brakes 2 separate circuits (hydraulically applied, fully enclosed wet disc brakes) • Automatic differential lock on front axle, limited slip • Swingable seat for tramming/drilling, including safety belt • Beacon warning lamp and break lights • 12V outlet for communication radio • Hydrostatic power steering system • FOPS-approved protective roof • Illuminated stairs for platform • Central lubrication system • Catalyser and silencer • Four-wheel drive • Boot washing kit • Fire extinguisher • Reverse alarm • Warning horn • Spirit levels
Simba M7 C
Specifications DRILL STEEL Rock drill
Hole diameter, mm
Drill rod
Shank adapter
Guide tubes
COP 1838ME
51–64
R32 Speedrod
R32
TDS 45
COP 1838ME
64–76
T38 Speedrod
T38
TDS 56/TDS 64
COP 1838HE
76–89
T45 Speedrod
T45
TDS 64/TDS 76
COP 2550UX
89–102
T51
T51
TDS 76
COP 2550UX
89–102
TDS 64/TDS 76
ST58
N/A
Optional equipment »Drilling system • Water mist ushing, water oil cooler, external air supply • Water mist ushing, air oil cooler, external air supply • Hole blowing kit • Dry drilling system • COP 1838MEX/COP 1838HE/COP 1838HEX, COP 2550UX
»Positioning system • Automatic lubrication for positioning/drilling system • Central lubrication for positioning/drilling system • Rod handling system RHS 27 on request (up to 51 m) • Thread lubrication kit • Stinger extension pieces
»Automation • Simba ABC Regular • Drill Plan Handling • Full Drill Data Handling • Rig Remote Access • Breakthrough Automatic Stop • Text Message System • Remote Cradle Control/Remote Feed Control • Void Detection • Total station navigation
» Water system • Water hose reel with dual control
» Power packs • Heater kit
»Electrical system • Soft start for 400–700 V • Electrical cable on reel, H07RN-F • Electrical cable on reel, Buex • Plug PC4 • Plug PC5 • Socket PC4 • Socket PC5 • Switch gear • Electrical outlet, 16 A • Extra transformer, 15 kVA • Extra working lights, 2 x 200 W, 24 V (on tripod)
»Cabin • FOPS-approved cabin: - Mediaplayer with USB port - Boot washing kit - Air conditioning unit without heating • Stainless steel cabin • Air conditioner with heating • Front window, 24 mm • Swingable operators seat • FOPS-approved grizzly bar for front window • Reversing camera with monitor • Joystick controlled spotlight
»Carrier • Fire suppression system, manual • Fire suppression system, automatic (check-re) • Fire suppression system, full automatic • Particle lter UNIKAT • Brake lights • L-carrier • Solid tyres • Deutz TCD 2013 L06 2V, 175 kW (238 hp)
»Miscellaneous • Manual rig washing kit • Manual lubrication kit • Hose and cable guide at water/cable reel • Link-one parts book • Remote operating kit • Additional panel • Manual spotlight
Simba M7 C
Measurements SIDE VIEW
www.atlascopco.com
0 6 9 2
M7 C
M7 C
2900
3740
4000 11560
COVERAGE AREA Dimensions in mm
Parallell holes wit h 0o boom-lift 35o boom-swing Coverage area 1100x4690 mm
850 Sting er extension 1200 (900) Feed extension
0 0 7
0 4 1 6
5 0 1 1
0 0 6 1 o
1 0 0 5 8 7
25o
90o 45o
35o o
360
Dimensions with 45o boom-lift 25o boom-swing 150 3900
1600
TURNING RADIUS
WEIGHT
depending on surface
gross weight
mm
0 0 9
Dimensions with 0o boom-lift 35o boom-swing
2000 Stinger extension
Outer
6,250
Inner
3,800
kg
Total
17,800
Boom side
12,300
Engine side
5,500
DIMENSIONS mm
Width
2,350
RECOMMENDED CABLE SIZE AND LENGTH
Height tramming
2,960
Voltage
Height roof up
2,960
Height with cabin (option)
3,050
Length tramming
9,460
Ground clearance
205
NOISE AND VIBRATION Operator sound pressure level in canopy, drilling,
75+- 3 dB(A) re 20uPa
free field (ISO 11201) Operator sound pressure level working close to
Dimension, mm 2
Diameter, mm
Length, m
400 V
H07RN-F
4G150
67
60
440 V
H07RN-F
4G120
60
75
440 V
Buflex
3x150+3G35
52
100
460–500 V
H07RN-F
4G120
60
75
460–500 V
Buflex
3x150+3G25
52
100
500–550 V
H07RN-F
4G95
55
90
500–550 V
Buflex
3x120+3G25
46
135
660–700 V
H07RN-F
4G70
49
110
106+-6 dB(A) re 20uPa
free field (ISO 11201) Operator sound pressure level in cabin, drilling,
Type
106+-6 dB(A) re 20uPa
. n o i t . a d m e r t o i b i f n h i o c r fi p i s c e i f p o s e r r o e f h t r t t e r a n e p C y r n e a m r o o t s s u t n C e t o n c o p c o e C h t s a f l t o A g r n i u y o p y t o l c u r s o n o e C s u . e d i c e z t i r o n o t h t u u o a h t n i u w y e n A g . n a o c h p c o o C t s s a t c l e t j A b f u o s s r e k r a a t m n e e d m a p r t i u e q r a e n d o n i t a a s c n i l o t b i u a c p fi i s i c h t e p n S i . s s e a r m t a x n e t l c a u n o d i o t r p p o l l h t A . i n w e t d n e e w m p S , i u o r q b e e w r o Ö , h B s A y s a l m l i r e D r u k c h o c o r R b o s c i p h o t C n i s s a o l t t A o , h 0 p 1 d 0 n 2 a t h s g n i o r i y t a p r o t C s u l l © I
machine, drilling, free field Sound power level (ISO 3744), drilling, free field
126 dB(A) re 1pW
Vibration levels seated, drilling (ISO 2631-1)
0.07+- 0.07 m/s^
2
Vibration levels standing, drilling (ISO 2631-1)
0.07+- 0.07 m/s^
2
660–700 V
Buflex
3x95+3G16
42
155
1,000 V
Buflex
3x50+3G10
32
275
G = Protection yellow/green Recommendations are given for surrounding temperature of 30oC.
0 1 0 2 / 1 1 b 1 0 4 9 1 2 1 5 8 9