BOSCH BATTMAX SERIES SPECIFICATION SHEET, INCLUDING BATTMAX4, BATTMAX 6, BATTMAX 8, BATTMAX 12, BATTMAX AUTOMATICFull description
Full description
functional specification for sapFull description
DCDU Specification
Full description
Caterpillar Torque Specification
SpecificationFull description
Piling Specification
QG Piping specification
FIREPROOFING SPECIFICATIONFull description
PROJECT SPECIFICATION
Electrical SpecificationDescription complète
Fireproofing specification from BorougeFull description
Coating specificationFull description
Full description
plumbing specifications
ballastless trackwork
PRODUCT ANALYSIS AND DEVELOPMENT Garment Specification sheet Submitted by Akriti Sharma (3) Ashish Kumar Annepu (7)
PRODUCT OVERVIEW
FRONT VIEW
REAR VIEW
Page 2 of 17
STYLE DESCRIPTION Brand
globus®
Style No:
LCSHR001
Merchandise category
Ladies casual wear
Season
Spring-summer 2011
Suitable Body type
Teen’s and adult women
Size range
XS,S,M,L,XL
Sample size
M
Technical designer
Alfred Winfrey
Date of design approval
12/10/2010
Verbal description
The garment is a ladies casual shirt with gathers on front and pleats on front and back panels. Sleeves are Cap sleeve variation with Gather at sleeve cap and bobbin elastic at the sleeve hem.
Fabrics
100% Cotton Fabric
Trims
Buttons, Elastic, Thread, Fusing
Labels
Brand Label, Size label, Wash Care label
Special Instruction
The garment fabric is to be dyed in green colour before production
Designer :- Sarah Rudolf Product id: LS4568
Product name : Ladies casual half sleeve shirt
Season : Spring summer 2011
Brand: globus®
Page 3 of 17
Page 4 of 17
SKETCH
BACK FRONT Page 5 of 17
MEASUREMENT DETAILS Size-M S.NO
PARAMETER
DIMENSION (INCHES) FRONT
1
Full-Length(from H.S.P)
24.5”
2
Shoulder length
15 “
3
Across chest 1” below armhole
4
Armhole round
16”
5
Across hem (half round)
20”
6.
Neck round
15 “
7
Side seam
14”
8
Front Yoke (length from HPS)
2”
9
Front Yoke (width)
4”
10
Length of upper front panel
10.5”
11
Length of lower front panel
12
18”
Page 6 of 17
12
V-neck opening at front
8.5”
13
Placket width
1”
14
Pleat width
¼” BACK
15
Centre Back Length
23.5”
16
Yoke length
4“
17
Yoke width
13”
18
Back panel length(excluding yoke)
19.5
COLLAR 19
Collar Stand
1”
SLEEVE 20
Cap Sleeve Length
5”
21
Sleeve Hem Round(relax)
10”
Page 7 of 17
HOW TO MEASURE 19
R 2
17
6
20
8 4
10 12
3
13
15
7
11
1
9
16
5
Page 8 of 17
18
CONSTRUCTIONAL DETAILS FRONT PLACKET • American irreversible placket. • A V-shaped opening at the front placket 8.5” of length from the centre front. • Spacing of 2” between two buttonhole
GATHERS AT UPPER FRONT PANEL • Gathers of 1” to be made on the upper front panel : where it joins the lower panel on either side
Page 9 of 17
PLEATS AT LOWER FRONT PANEL • 3 pleats of ¼” each to be made in the lower front panel coinciding with the gathers on the upper panel on either side
PLEATS AT BACK • 3 pleats of ¼” each to be made at back •
The distance of the first pleat from centre front has to maintained as 4”
• Pleats to be made on either side
Page 10 of 17
SLEEVE • Puff Sleeve with the hem done by elastic bobbin thread •
Irregular gathers at sleeve cap.
Page 11 of 17
C0 1
F02
B0 2
S0 2
C0 2
F03
B0 3
S0 3
F04
OPERATION PROCESS FLOW
COLLAR
S0 1
SLEEVE
B0 1
BACK
FRONT
F01
F05
ASSEMBLY F06
A0 1
A02
Page 12 of 17
A03
A04
AO 5
A06
A08
A07
OPERATION BULLETIN AND DETAILS OP. No.
OPERATION
SPI
Stitch Type
Machine used
Seam Type
FRONT ASSEMBLY F01
Pleat on lower front panel
12
301
SNLS
Class 5-Decorative Seam
F02
Make Gathers at upper front
12
301
SNLS
Class 5-Decorative seam
F03
Attach Lower and upper front Panel
12
301
SNLS
Class 1- superimposed seam: SSa
F04
Edge finish Lower and upper front Panel seam by Over lock
