Technical of Our Diamond Tools

Technical of our diamond tools 1. Polishing Pad Flexible Wet Polishing Pads The faces of polishing pads are designed with straight or curved slots, so they could be bent or distorted freely. They are backed with loop Velcro so they could be attached to any of backer pads very easy. They are used for fabrication of marble, granite, ceramic, and other hard and fragile material, as well as non-iron metal. They are widely used to polish stone, porcelain profiles, tile floors, all kinds of table-boards and stone sculptures. Their working layer thickness is 2.2mm, 3mm or 4mm They are suitable for hand power machines with the power is 750W to 1500W that run up to a speed of 2000-10000 rpm. Flexible Polishing Pads attach to the Flexible Backer pads are used for grinding profiles or concave or convex surface as well as flat surface of stone, while attach to the rigid backer pads are perfect for grinding a flat or level surface like floor. The process procedure: the operator sticks the flex pad on a backer pads and screw into Arbor of a grinding machine, and then brings to bear some pressure to the machine to grind stone surface for five times come-and-go, at the same time, the operator must infuses water into the backer pad continuously during the operation. Then, the operator should change a finer pad. The grits of pads are from #50, #100, #200, #400, #800, #1500, #3000, and #5000 to white/black buff in turn.According to the stone's quality and operator's experience, it could be cut down or save some positions of pads. White buff is used for light color stones and black buff for dark color stones. Each of grit is easily distinguished by different color of Velcro and the grit mark on the pad. They are worked by water fed during the operation, so they are also called wet pads. GRIT

#50

#100

#200

#400

#800

#1500

#3000

#5000

BUFF

COLOR

BLUE

YELLOW

ORANGE

RED

DARK GREEN

LIGHT GREEN

COFFEE

WHITE

WHITE

GLOSSY

1

2

5

10

20

35

65

85

90

WATER QUANTUM

MUCH

MUCH

MUCH

FEW

FEW

FEW

FEW

FEW

MIDDLE

Measly water is needed from #1500, to #3000. For the buff, only less water is needed to wet the stone surface. This would make more friction resistance, and enough temperature on the surface of stone. Then stone surface is easily to be wiped off because of intenerate caused by momentary high temperature. But the stone couldn't be grinded by dry with too long time or it will result in burning or pigmentation. If burning appears, the worker must do work over again from #200 at least, and if the pigmentation appears, it must be from #400.

PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn

Flexible Dry Polishing Pads Some special floors (e.g. hotel's stone floorboard) are not allowed to work by wet, so the dry pads are used. Ordinarily, the dry pads will not cause burning and pigmentation because of using the special resin to make the surface of pads intenerated and pealed off as well as to avoid too hot on the surface of stone.

They are excellent for marble polishing. They can be used by wet as well.

Flexible Buff Pads As the last position of pads or as the last stage of the fabrication, these pads are designed to create a deep glossy reflection mirror like on marble, terrazzo and granite. Only a little water is necessary so the pads can work with heat and water and a smooth finish surface would be done quickly. The pads are made from tin oxide and natural fibers and special bond that are heat compressed into a mould. As there are no dangerous chemicals involved, the Buff Pads are environmental safe and easy to use.

Flexible Resin-Pregnant Diamond Metal Chips Polishing Pads For improving the efficiency to quickly remove stock and for increasing the Durable life of pad set significantly, we creates resin-metal-bond polishing pads, available from #30, #50, #100,#200 to #400, available both by wet and by dry. They are made with pregnant diamond metal chips with unique resin bond. They are heat compressed into a mould. This is a new kind of high capability pads. They can be applied to excellent fabrication of marble, concrete and granite . They are welcomed by our consumers with very much interest. Customer Logo printed is available on request for volume order.

Flexible Metal bond Polishing Pad Sintered metal bonded with Rubber backer pad backed applied to quickly remove stock. They are available from #30, #50, #100,#200 to #400 .


Flexible Electroplated of Diamond Polishing Pads Electroplated of diamond crystals on a flexible cloth with dot matrix or a special pattern, they are mainly used for dry polishing. They are available from grit #60, #120, #200 to #400 .

Convex Polishing Pads They are designed for polishing curved or inner concave parts of countertops, furniture, sinks, and cast stone. Available in 3". Customer Logo printed is available on request for volume order. POLISHING PAD-SKETCH MAP


2. Brazed Polishing Pads Brazed Polishing Pads Velcro or Rubber Backer Backed Brazed diamond on a thin round steel sheet with Velcro or Backer pad backed. You can easy mount on any machine. Since it is a brazed diamond tool with 50-80% diamond exposure it can be applied to excellen heavy removal for marble, concrete and granite wthout shaking even run by dry. it is available in both 4" ,4-1/2"and 5" diameter and available on request upon a specific drawing of customer in any diameter for a volume order. Customer Logo printed is available on request for volume order.


3. Floor Polishing Pads Floor Polishing Pads They are designed for floor polishing machines to polish or restore or maintain for the floor of marble, concrete, terrazzo, granite. They are backed with Velcro, can be mounted on a rigid backer pad to fit on any floor machine. The high thickness provides extended life. Our resin-pregnant diamond Metal chips floor polishing pads, available from #30, #50, #100, to #200, are for quickly remove stock with durable life. This is a vitally important innovation in diamond tools industry. Our high concentration of diamond resin floor polishing pads from #400, #800, #1500 to #3000 are made from heavy-duty resin with high quality diamond powder. Using our set of floor polishing pads you can make the floor glossy finish perfectly. They are available in wet and dry on request. We have many kinds of rigid backer pads; they are bakelite baker pad, aluminum backer pad, aluminum and rubber composite backer pad with female threaded 5/8-11" or M14 and availble with other threads on request. Available in 3" and 4" diameter, thickness from 8mm to 12mm on customer request. We have sintered cup wheels; they are designed to initially shape the floor of concrete, terrazzo and granite. Customer Logo printed is available on request for volume order.


4. Sintered Router Bits Sintered Router Bits for Portable profile machines These Sintered Router Bits have a M8 threaded bolt attached and a M10 threaded bolt backed up to fit on any Portable Profile Machine. They may be run by wet with the water rushed from a attachment of the machine. Choose from segmented for aggressive stock removal or continuous rim for a smoother finish. Customer Logo printed is available on request for volume order SKETCH MAP

Sintered Router Bit for Angle Grinders These Sintered Router Bits for Angle Grinder have a 5/8"-11 or M14 female threaded on customer request to fit on any Anger Grinder. They may be run by wet with the water out from the center hole and vents inside the arbor. Choose from segmented tools for aggressive stock removal or continuous rim for a smoother finish. Attached with a composite elasticity gasket for vibration v ibration-proof -proof is available.



5. Brazed Router Bits Brazed Router Bit for Angle Grinders Grinders These Vacuum Brazed Router Bits for Angle Grinder have a 5/8"-11 or M14 female threaded on customer request to fit on any Anger Grinder. They may be run by wet with the water out from the center hole and vents inside the arbor.They can be run by dry also. Vacuum Brazed Router Bits are great for grinding shapes without bouncing or loosing their shape. They feature 50% up to 80% diamond exposure to ensure you that get the fastest removal rate. We strongly suggest our customer to choose Sintered as POS1, Vacuum Brazed as POS2 and POS3, and then resin polishing wheels as POS4, POS5 and POS6. They are excellent for fabrication of marble, granite, reinforced fiber composites, hard rubber, hard plastic, carbon fiber composites, glass … Attached with a composite elasticity gasket for vibration-proof is available. They are the best tools to replace electroplated Router Bits. The life of brazed bit is 5 times than electroplated. Customer Logo printed is available on request for volume order.

Brazed Router Bits for Portable profile machines These Vacuum Brazed Router Bits have a M8 threaded bolt attached and a M10 threaded bolt backed up to fit on any Portable Profile Machine. They may be run by wet with the water rushed from an attachment of the machine. They can be run by dry also. They are great for grinding shapes without bouncing or loosing their shape. They feature 50% up to 80% diamond exposure to ensure you that get the fastest removal rate. We strongly suggest our customer to choose Sintered as POS1, Vacuum Brazed as POS2 and POS3, and then resin polishing wheels as POS4, POS5 and POS6. They are excellent for fabrication of marble, granite, reinforced fiber composites, hard rubber, hard plastic, carbon fiber composites, glass … They are the best tools to replace electroplated Router Bits. The life of brazed bit is 5 times than electroplated. Customer Logo printed is available on request for volume order.


6. CNC Profile Wheels We offer the high quality and reliability of CNC profiling wheels for the profiling of granite, marble and synthetic stone. They are sintered and welded in a mould at same time under strict guidelines with the best diamond available. Segmented tools are for aggressive stock removal and continuous rim for a smoother finish. Available upon a specific drawing of customer, we can make any wheel in any diameter requested and with a combination of many different shapes.

Vacuum Brazed CNC Profile Wheels They are great for grinding without bouncing or loosing their shape. They are perfect to be position 2 and 3 in the set of tools. The set of tools consists of 3 metal bonded diamond wheels perfectly matched to 3 resin diamond polishing positions. This makes it possible to obtain the maximum degree of finishing without the need for manual working. We strongly incline the set of tools consists of 1 sintered metal bonded profile wheel as position 1, 2 Vacuum brazed wheels as position 2 and 3, and then matching to 3 resined polishing wheels as position 4, position 5 and position 6. Standard bore is 35mm, available in other bores. Our wide ranges of profile wheels are suitable for use on all major CNC machines Available on request for Marble and Granite, upon a specific drawing of customer, these wheels can be made in any diameter requested and with a combination of many different shapes. Delivery time is less than 4 weeks. Customer Logo printed is available on request for volume order.


7. Finger Bits They are designed with G1/2" male thread, mounted on a CNC machine,working as milling cutter for cutting any arc of granite or marble or other stones under the control of CNC machine, continuous rim with arc slots and water vents throughout of body. Other styles are available according to the drawings of customer. Available in both sintered and vacuum brazed. Sintered is more economical and vacuum Brazed is great with high efficiency without bouncing or loosing their shape. Designed with edge 3/16" Radius or other shape edge make a finger bit becoming a Pofile Finger Bit, or 2 in 1. We offer many adapters. Adapter unit screws into a Finger Bit to affect operative compatibility between different machines. It is available on request upon a specific drawing of customer in any diameter and length. Customer Logo printed is available on request for volume order.

FINGER BIT-SKETCH MAP


SPECIFICATION:


8. Sintered Drill Bits Sintered Crown Core Bits Our Core Bits are thin wall drilling tool with a hole through the center that let water feeds into and removes sediment stone chips and allows the Core pedestal to pass through the Bit and into the Core barrel. Our Drill Bits, used with high quality diamond and strong bond, sintered into a mould, are Laser welded. They are high diamond concentration provide aggressive cutting action, excellent for drilling marble and granite with high performance and durable life. They are designed with 5/8"-11 or M14 or M10 female thread and attached with a composite elasticity gasket so they can be mounted to any angle grinder and work on stone with vibration-proof. We offer many adapters. Adapter unit screws into a Drill Bit to affect operative compatibility between different machines.

Sintered Non Core Bits

A non Core Bit is a drilling tool with a hole through the center that let water flows and removes sediment stone chips. chip s. It drill the stone complete section with no core. They are designed with composite threaded both with G1/2" male threaded and 5/8”-11 or M14 female threaded, so that they can not only be mounted to any angle grinder but also can be used on CNC machine. Attached with a composite elasticity gasket with vibration-proof is available for all drill bits. Available in G1/2", 5/8”-11, M14, M10, 3/8” Shank, 1/2” Shank on customer's order. We offer many adapters. Adapter unit screws into a Drill Bit to affect operative compatibility between different machines. It is available on request upon a specific drawing of customer in any diameter and length requested. Customer Logo printed is available on request for volume order.


9. Brazed Drill Bits Crown Core Bits with brazed of Diamond wall Called Sintered Crown Core Bit with Vacuum Brazed Drum Beside the sintered tips, they are brazed of diamond on the wall of the crown Core Bits, so a normal Core Bit become a drum grinder, it is extended a amusing application for a Core Bit.

Vacuum Brazed Core Bits & Drum Grinder They are thin wall Core Bits and Drum Grinders. They are used when it is not allowed to drill hole or extend hole by wet on granite, marble, porcelain, ceramic tile.

Vacuum Brazed Drill Bits They are thin wall designed. They are used when it is not allowed to drill hole by wet on granite, marble, porcelain, ceramic tile. Attached with a composite elasticity gasket for vibration-proof is available for all drill bits. Available in G1/2", 5/8”-11, M14, M10, 3/8” Shank, 1/2” Shank for all drill bits on customer's order. It is available on request upon a specific drawing of customer in any diameter and length requested. Customer Logo printed is available on request for volume order


10. Sintered Cup Wheels They are designed to initially shape the stone and take out deep saw scratches on marble or granite. We make 3 ” cup wheel for the floor of marble, concrete, terrazzo, granite. We offer many kinds of styles cup wheels with steel backer or aluminum backer or rubber backer. They are suited for all kinds of machines with Arbor 5/8 ”-11 threaded or M14 threaded or snail lock. They are available in COARSE, MEDIUM, FINE, And VERY FINE. It is Available on request for a specific drawing of customer. Customer Logo printed is available on request.

SPECIFICATION-SINGLE CIRCLE

DIMENSION：

D2

D1

R1

R2

W

LENGTH×WIDTH×DEPTH

50

43

30

30×7×5

62.5

54.5

38

38×8×5

150

75

67

45

45×8×5

175

87.5

79.5

52

52×8×5

100 125

φ20、M14、M16、5/8"-11、Snail Lock


TYPE：

NO

DIAMETER(D2)

1

4"

2

5"

3

6"

4

7"

Thread Size (D1)

GRIT


#35/40、#70/80、#140/200

SPECIFICATION-DOUBLE ROW

DIAMENSION： D2

R1

R2

r1

r2

W1

W2


100

50

43

37

31

30

20

30×7×5 ,20×6×5

125

62.5

54.5

47

40

38

25

38×8×5 ,25×7×5

150

75

67

56

49

45

30

45×8×5 ,30×7×5

175

87.5

79.5

65

58

52

35

52×8×5 ,35×7×5

SPECIFICATION-RADIATE


DIAMENSION： D2

D1

100 125 φ20、M14、M16、5/8"-11 、Snail Lock

150 175

R1

R2

W


50

43

30

30×7×5

62.5

54.5

38

38×8×5

75

67

45

45×8×5

87.5

79.5

52

52×8×5

SPECIFICATION： NO

DIA（D2)

1

4"

2

5"

φ20、M14、M16、5/8"-11、Snail

3

6"

Lock

4

7"

THREAD SIZE (D1)

SPECIFICATION-TURBO


GRIT

#35/40、#70/80、#140/200

DIAMENSION： D2(mm)

D1

d2(mm)

d1(mm)

60

30

75

30

150

90

30

175

105

30

100 125


SPECIFICATION： NO

DIA(D2)

1

4"

2

5"

3

6"

4

7"

THREAD SIZE (D1)

GRIT


#35/40、#70/80、#140/200


11. Brazed cup wheels Vacuum Brazed cup wheels are great for grinding bevels or shapes without bouncing or loosing their shape. Available in both 4" and 5" diameter. Other styles are available according to the drawings of customer Available in Bore16mm, 7/8", female 5/8"-11 and M14 or on customer's order. It is available on request upon a specific drawing of customer in any diameter and height requested. Customer Logo printed is available on request for volume order.


12. Diamond Polishing Bricks They are used to replace Silicon Carbide Bricks. Our Sintered Diamond Bricks, grits from #30/40, #40/50, #50/60, #70/80, #80/100, #100/120 to #140/200, are designed to initially shape with high stock removal rate for the slab fabrication of granite or marble. The rubber iterlayer make f or vibration-proof. vibration-proof. Our high concentration of diamond Resin Bricks from #300, #400,# 500, #800, #1500 to# 3000 made from heavy-duty resin with high quality diamond powder are perfect for polishing granite or marble. Our BUFF Bricks made of special rubber bond and tin dioxide and other materials make high glossy finish on the slab of granite perfectly. White BUFF is for light color granite and black BUFF for deep color granite. It is available on request upon a specific drawing of customer in any size. Customer Logo printed is available on request for volume order. SPECIFICATION


NO

DIA

BOND TYPE

GRIT

1

#35/40

2

#40/50

3

#50/60 METAL

4

#70/80

5

#80/100

6

#100/140

7

#140/200

8

#200

135mm,140mm,

9

#300

10

#400

11

#500

12

RESIN

#1000

13

#2000

14

#3000

15

#5000

16

BUFF


13. Vacuum Brazed Dishs Vacuum Brazed Dishes are great for grinding bevels or shapes without bouncing or loosing their shape. Available in both 4" ,4-1/2"and 5" diameter. Other styles are available according to the drawings of customer. Available in Bore16mm or 7/8", or laser welded 5/8"-11 threaded Nut or M14 theaded or M10 threaded Nut, on customer's order. It is available on request upon a specific drawing of customer in any diameter and height requested. Customer Logo printed is available on request for volume order.


14. Drum Grinders They are used with an up and down motion, excellent for grinding an inside circle, oval, or arc of granite or marble or other stones. The sintered drums are economic for longer life. The brazed drums are for fast cutting and could be used by dry. The resin drums are for polishing, with rubber interlayer they can work at high speed smoothly. Available in G1/2", 5/8”-11 female threaded, M14 female threaded, M10 female threaded, 3/8” Shank, 1/2” Shank on customer's order. We offer many adapters. Adapter unit screws into a Drum Grinder to affect operative compatibility between different machines. It is available on request upon a specific drawing of customer in any diameter and length requested. Customer Logo printed is available on request for volume order.


15. Backer Pads The backer pads are hook Velcro backed, they accept polishing pads with Velcro loop backed. We have rigid backer pads made from Bakelite, Flexible backer pads made from rubber, extremely flexible backer pads made from supper quality rubber . Our extremely flexible backers are great for ogees. Flexible backer pads are used for grinding profiles or curves surface of stone while the rigid backer pads are for grinding plane or floor. All the backer pads are ideally suited for all kinds of machines with Arbor 5/8 ”-11 threaded or M14 threaded. It is available on request upon a specific drawing of customer in any diameter and height requested. Available in 3",4", 5",6",7" diameter.

Snail Lock Adapter They are made from Bakelite or Rubber with hook Velcro backed, they accept polishing pads with Velcro loop backed. Available in 4", 5", 6" and 7" diameter. We also produce polishing pads with a snail lock adapter . Customer Logo printed is available on request for volume order.

Adapters They are made from stainless steel. Adapter unit screws into a core bit or a drum to affect operative compatibility between different machines. It is available on request upon a specific drawing of customer in any diameter or thread and length.

Customer Logo printed is available on request for volume order.


SPECIFICATION:

DIAMENSION： D

60, 80, 100, 125, 150

d

M14, M16, 5/8"-11, snail lock


16. Diamond Hand Pad Hand-Hold Hand-Hold Flat and Profile Polishing Pads They are foam backed for polishing on the surface of marble, granite, ceramics, glass and hard composites. Flat pads are for for polishing plane and the Profile Pads are allowed for easy polishing the profile shapes or the areas that are hard to polishing by machines. They are good at edging or seaming polishing. For the coarser grit pads are electroplated diamond on flexible cloth and foam-backed, available in the grits# 60, #120, #200 and #400. For the finer grits, they are resined diamond on flexible cloth and foam-backed available in the grit #600, #1800 and #3500. Customer Logo printed is available on request for volume order.


17. Other Product

Vacuum Brazed Anchor Bits We offer many kinds of Vacuum Brazed like 3/8", 1/4" or 3/16" of diamond Anchor Bits. Standard Shank is 3/8". Other shanks like 1/4" or non Standard Anchor Bits are available on the request of customer. Customer Logo printed is available on request for volume order. Here is the diagram for the application of an Anchor bits. After milling the hole, the slab of stone is mounted by an anchor bolt to the base.

JIGSAWS straight narrow vertical blade, used to cut sharp corners or joints of slabs, where could not be cut by a circular saw blade, by up-down motion, it is also for cutting curves in granite, marble, ceramic tiles and many other natural or artificial stones. We have sintered and Vacuum Brazed diamond Jigsaw both welded by laser. Customer Logo printed is available on request for volume order.

Sintered Router Tip Other threads are available on customer's order. It is available on request upon a specific drawing of customer in any diameter and length requested.

Brazed tips of diamond wire saw We offer many sizes of brazed tips of diamond for manufacture of diamond wire saw.


18. Cutting Tools Gang saw segment Brief introduction: For cutting marble, limestone and other soft stone. Regular sizes are as following, other specifications and sizes are available upon request.

Thickness of the

Height of the

Legth of the

Width of the

Height of the

Length of the

blade(mm)

blade(mm)

blade(mm)

segment(mm)

blade(mm)

blade(mm)

3

180

3.0-4.0

4.5

7

20

3.5

180

3.0-4.0

5

7

20

Please forward us the following technical data when ordering the above products. Diameter:

Specificati on of Segment

Order Amount

Diameter of Inner hole

Number of Segments in Each Blade

Delivery Date:

Cutting Material

Please forward us the following technical data if it is available for you! Turning Speed of Blade(rpm/min)

Linear Speed(m/min)

Cutting Depth(m/min)

Cutting Depth(mm)

Main Characteristic of Cutting Material


Motor Power(KW) Cooling Water Comsuption(L/min)

Horizontal cutting blade Brief introduction: High frequency welded, for horizontal cutting marble ,granite, basalt and so on Characteristics of products: Good sharpness, stable cutting, flat cutting gap

Diameter (mm )

Universal disk thickness(mm)

W1( mm)

H(mm)

L(mm)

Number

300

2.8/7

4.5

10

40

21

350

2.8/7

4.5

10

40

24

400

2.8/7

4.5

10

40

28

450

2.8/7

4.5

10

40

32



Order Amount



Delivery Date:

Cutting Material


Linear Speed(m/min)


Cutting Depth(mm)




multi-saw blade and segment Brief Introduction: High Frequency welded or brazing welded,numerously used for cutting granite Characteristics of products:Sandwich structure, fast, straight and stable cutting with flat slab,good life span.

Regular sizes are as following, other specifications and sizes are available upon request.

Diameter (mm )

W1

W2

H

L

Number

1000

6.9

6.1

13

24

70

1200

7.4

6.6

13

24

80

1300

8.4

7.6

13

24

88

1400

8.4

7.6

13

24

92

1600

9.2

8.4

13

24

108



Order Amount



Delivery Date:

Cutting Material


Linear Speed(m/min)


Cutting Depth(mm)




Blade and segment for cutting large size block

Diameter (mm )

W1

W2

H

L

Number

900

6.9

6.1

13

24

64

1000

6.9

6.1

13

24

70

1100

7.4

6.6

13

24

74

1200

7.4

6.6

13

24

80

1300

8.4

7.6

13

24

88

1400

8.4

7.6

13

24

92

1500

9.2

8.4

13

24

100

1600

9.2

8.4

13

24

108

1700

9.2

8.4

13

24

112

1800

9.9

9.1

13

24

120

2000

11.0

10.0

15

24

128

2200

11.0

10.0

15

24

132

2500

12.5

11.5

20

24

140

2700

12.5

11.5

20

24

140

3000

12.5

11.5

20

24

160

3500

13.0

12.0

20

24

180


Wire saw Brief introduction: For quanrrying,profiling and block finishing of granite,marble,limestone and other stone, and also cutting concrete. Characteristics of products: Good sharpness, moderate life span, stable performance.

Specifications,technics and sizes are available upon requests. Height of Specifications Diameter

working

（mm） Material

（mm）

layer

Length

to cut

（mm）

Usage

Techniques

（mm）

11

11

6

9.5

Marble

Quarrying Sintered

10.5

10.5

6.4

10

Marble

8.5

8.5

6

9.5

Marble

Profiling

Sintered

8.8

8.8

6

9.5

Marble

Profiling

Sintered

11

11

6.4

10

Marble

Quarrying Sintered

11.5

11.5

6.4

10

Marble

Quarrying Sintered

10.5

10.5

6.4

10

Granite

11

11

6.4

10

Granite

8.5

8.5

6

9.5

Granite

Profiling

Sintered

8.8

8.8

6

9.5

Granite

Profiling

Sintered

11

11

6.4

10

Concrete Conc rete Cutting

Sintered

11.5

11.5

6.4

10

Concrete Cutting

Sintered

Block squaring

Block squaring Block squaring

Sintered

Sintered

Sintered

Cutting parameters Number (mm)

of

Specifications beads/ meter

Installation Material to method

cut

Usage

m/s

Cutting

(㎡

Liner

speed

/m)Life

speed

(cm/h)

span


Soft marble quarrying

30-35

Medium 11

28

Spring

hard

quarrying

28-32

quarrying

26-30

marble Hard marble

Soft marble

Medium 10.5

37

Plastic

hard marble

Block

'9-12(㎡ /h) '7-10(㎡ /h) '4-8(㎡ /h)

25-45

15-25

'10-20

30-35

90-130

30-40

28-32

70-100

25-30

26-30

60-80

20-25

30-34

100-150 35-45

Profiling

28-32

80-120

25-35

Profiling

26-30

70-100

20-30

squaring Block squaring

Hard

Block

marble

squaring

Soft marble Profiling Medium 8.5/8.8

37

Plastic

hard marble Hard marble

Soft granite quarrying

24-28

Medium hard 11.5/11

40

Rubber

granite Abrasive granite

Soft granite Medium hard 37/40

Plastic

22-24

quarrying

18-22

quarrying

26-30

granite Hard

10.5/11

quarrying

granite

Block squaring Block squaring

Hard

Block

granite

squaring

Abrasive

Block

'4-7(㎡ /h) '2-4(㎡ /h) '1-2(㎡ /h) '4-7(㎡ /h)

'10-20

'8-14

'6-9

'10-20

22-26

60-100

9—12

20-24

40—60

8—15

18-22

25—45

6—8

22-26

60-100

12—20


granite

squaring

Soft granite Profiling

24-28

60-80

9—13

Profiling

22-26

30-60

7—11

Profiling

20-24

20-35

5—8

Profiling

24-28

60-80

9—13

Cutting

22—25 2—5

2—7

Cutting

20—22 1—2

1—2.5

Cutting

18—20 0.5—1

0.5—1.2

Medium hard granite 8.5//8.8

37

Plastic Hard granite Abrasive granite

Low intensity

10.5/11.5

Plastic+

concrete

Spring

Medium

40

intensity Rubber+ Spring

concrete High intensity concrete


Linear Speed(m/min)


Cutting Depth(mm)




Blade and segment for cutting stone edge and small size block Brief Introduction: The saw blade uses high fruquency welding or laser welding, applicable for the cutting of airport raceway, highway and building decoration. It also can be used for dismantling building with concrete,steel framework ,opening the hole for door and window., characteristic of products: sharp cutting, long life, strong brazing,heat resistant, safe use and easy operation.

Other specifications and sizes are available upon request! Diameter(mm)

Segment Length(mm)

Segment Width(mm)

Segment Height(mm)

230

40

2.6

10

250

40

2.8

10

300

40

3

10

350

40

3.2

10

400

40

3.5

10

450

40

4

10

500

40

4.4

10

600

40

4.8

10

650

40

4.8

10

700

40

5.2

10

750

40

5.5

10

800

40

5.8

10

1000

24/40

6.5

10

1200

24/40

7.5

10

1400

24/40

8.5

10

1600

24/40

9.5

10

Inner Hole(mm)

20/22.23/25.4/32/50/60



Order Amount



Delivery Date:

Cutting Material


Blade for manual cutting machine Brief introduction: For cutting and nondestructive grooving on marble,granite,ceramic tile,concrete,decorative material, used on manual cutting machine.

Characters of the products: fast cutting speed,samll cutting gap, low power consumption,sharpness,abrasiveness

Commodity

Diameter(mm)

Segmented cutter

Hole(mm)

Size of segment

Number of teeth

105

1.8*7.5

8

Segmented cutter

115

1.8*8.0

9

Segmented cutter

125

2.0*8.0

10

Segmented cutter

150

2.0*7.5

1

Segmented cutter

180

2.2*8.0

14

Segmented cutter

200

2.2*8.0

14

Segmented cutter

230

2.4*8

16

Segmented cutter

250

2.4*8.0

18

Segmented cutter

300

2.6*8.0

22

Segmented cutter

350

2.8*8.0

24

Turbo cutter

105

2.0*8

45

Turbo cutter

105

2.0*10

60

Turbo cutter

115

2.0*7.5

48

16/20/22.23/25.4/50

16/20/22.23/25.4/50


Turbo cutter

115

2.0*10

66

Turbo cutter

125

2.0*8

48

Turbo cutter

125

2.2*10

72

Turbo cutter

150

2.2*8

72

Turbo cutter

150

2.2*10

84

Turbo cutter

180

2.4*8

80

Turbo cutter

180

2.4*10

100

Turbo cutter

200

2.4*8.0

90

Turbo cutter

230

2.6*8.0

72

Turbo cutter

230

2.6*8.0

140

Turbo cutter

230

2.6*10

120

Turbo cutter

250

2.6*10

130

Continuous rim cutter

105

1.8*8


110

1.8*9


115

1.8*8


125

1.8*8


150

1.8*8


180


200

2*8


230

2*9


250

2*10


300

2.2*8


350

2.6*8


400

2.8*8

16/20/22.23/25.4/50

1.8*8

Operation notes:

（1）Pay attention to the joining and the rotating direction of motor shaft and hole of cutter, defected blades are forbiddened. （2）Do not cut metal, or the blade will become blunt and the life span will be shortened. （3）For the cutter is thin, do not put pressure on its sides or carry out curvilinear cutting, avoid tangency between edge of blade and

spare parts when it feeds. （4） Carborundum abrader, firebrick and grinding wheel are recommended in case blade cann't open （5）For safety use, blade cover is needed for the cutting machine, the operator should wear safety dressing, glasses and other

protective articles. （6）Water cooling is needed when use wet cutter, otherwise life span of cutter will be shortened.


19. Antique Brush Frankfurt Abrasive Brush

YIDIC Abrasive Brushes Frankfurt Frankfur t are used in handed and automatic grinding machine, step-retreading step-retre ading machine etc.Grit mesh: stainless steel, steel +36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#....


Fickert Abrasive Brush

Fickert abrasive brushes are used in granite automatic grinding line.Include eleven filaments: stainless stain less steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#....

Diam. 110mm M14 Abrasive Brush

Diam.110mm MA14 abrasive brushes are used in handed grinding machine.Include machine.Include eleven filaments: stainless stain less steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#...

Diam. 200mm Round Abrasive Brush

Diam.200mm round abrasive brushes are used in stone industrial polishing lines.Include lines.Includ e eleven filaments: stainless steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#....

Diam. 250mm Round Abrasive Brush

Diam.250mm Round Abrasive Brushes with Velcro back is used in automatic grinding machine, antique stone industrial lines. Grit mesh: stainless steel, steel+36#, steel+36# , 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#. ...

Snail Lock Abrasive Brush

Snail Lock Abrasive Brushes are used in side grinding machine and step retreading machine.Grit mesh: stainless steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#. ...

Diam. 110mm M16 Abrasive Brush

Diam.110mm M16 is used in handed grinding machine.Grit mesh: stainless steel, steel +36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#....

WHAT IS OUR ABRASIVE BRUSH FOR STONE? Our brushes adopt Dupont nylon filaments with silicon carbide grit inside. It has different kinds and grit, could fit in hand grinding machine, industrial polishing lines .step retreading machine and hand-controlled machine and so on to deal with natural stone and artificial stone .With the most fine grit ,the surface can be polished ,get satin result ,and stone natural texture can be appeared .At the same time ,the stone achieve antique look surface and satin repellent ability can be improved .At the same time it could improve the antifouling and skid prevention


HOW IS PRINCIPLE OF OUR BRUSH? When the abrasive brush is using for treating the stone, the silicon carbide grit inside can grind and polish the surface. Because of the flexibility of the filament, under the press, the abrasive filaments can touch, grinding and polishing the all of surface even if the surface is uneven. With the most fine grit, the surface can be polished, get satin result, and stone natural texture can appeared. At the same time, the stone achieve antique look surface and satin repellent ability can be improved.

WHAT S THE ADVANTAGE? ’

Our abrasive brushes adopt top quality and low density nylon, reducing the cost and enhancing the efficiency. Our filaments show the wave shape, the polishing effect is good and long life. Our brush could keep rigidity and tenacity in humidity circumstance. Our brushes have the better resilience. Our brush could keep the best life. Logical height and density guarantee the best effect and life. Adopting fixed the filaments in fourth directions, prevented the filaments broke off during working .Guarantee the best life of our brush. Our steel brushes adopt high strength and special elastic stainless steel. The speciation is entire and is used in varied polishing and retreading machine. Grit is entire and guarantee different grinding effect. We could order in advance different abrasive brush according to special machine.

WHY ADOPT DUPONT PROFESSIONAL FILAMENTS? Dupont Company invented Nylon and aggressive nylon filaments, it takes up the first place in the craft in the world. Amount these our abrasive brush adopt Tynex A which distribute different grit in the nylon 612,adopting special craft ’

making the filaments wave shape ,then guarantee the grinding effect and enhance the working efficiency.

WHY ADOPT NYLON 612? Nylon 612 can retain rigidity and tenacity in humidity circumvents .With adding water ,the other kind of nylon will be softening and loss rigidity .Nylon 6/66/610 comes from biology and petroleum polymer without consistent quality .Nylon 612 with lower bibulous and density characteristic is the best filament for abrasive brush .

WHY DOES IT ADOPT WAVE SHAPE FILAMENTS? Strengthening the elastic of the filaments, to guarantee the best polish effect of our brush. Make the filaments separate each other, more uniformity grinding on the stone surface. Increasing the hardness of the filaments, improving the polish efficiency. Decreasing the possibility of filaments broke off because of centralized, guarantee the best life of our brush.

HOW TO IDENTIFY THE QUALITY OF BRUSHES? The filaments cannot brush off during working. The filaments fixed to the frame with high strength stainless steel wire prevented from corrosion. Filament should be bended wave shape. The silicon carbide grit in the filaments shouldn’t break off because of the wave shape filaments. The appropriate height and density of the brushes. The filaments should have the good wave resilience. The filaments should have the long life.


IS LONGER LIFE OK BY HIGHER FILAMENTS? Not allowed, because the life of brush depends on the making craft, filaments quality and right using method. If adding the height of the filaments unwisely ,then won ’t guarantee the rigidity, it will fall down during working ,so filament side over grind and cause them thin ,then will rapture earlier and loss their life .

WHAT'S THE EFFECT FOR GRANITE AFTER GRINDING ? The granite after grinding ,have the uneven archaized effect ,showing the nature light ,and could have the antifouling and skid prevention. wishing to get get the above effect effect ,before the grinding it must be dealt with the flaming pan . and so on surface; surface; first using steel brush removing the surface and fix it ,then using the abrasive brush from thick to thin ,until to get the satisfied effect .

WHAT'S THE EFFECT FOR MARBLE AFTER GRINDING ? Most marble could get the antique effect directly dealing with it ,showing the nature light ,and could have the antifouling and skid prevention. As some stone before grinding ,according to need need and structure ,dealing with in advance in physical methods ,then using the grit no from thick to thin to grind it, until the pan could get the satisfied effect .

HOW MANY KINDS AND GRITS FOR THE BRUSH ? According to the kinds ,it has Frankfurt (horseshoe),Diam 110mm round brush .Fickert (brad) and so on ;According to the grits included steel. 36# .46#、60#、80#、120#、180#、240#、320#、500# and so on .Frankfurt is used in hand grinding machine ,industrial polishing lines step retreading machine ,round brush is used in hand grinding machine step retreading machine ;Fickert is used in automatic grinding machine .

HOW TO CHOOSE VARIED KINDS OF BRUSH? Usually ,steel and grit 36# abrasive brush is removing the surface loose and pan stereotypia; grit 46# 60# 80# for grind simply ;120# 180# 240# could polish simply ;320# 500# could polish fine ,to getting the archaized effect. If it is the first time to use the abrasive brush ,should test in each grit ,to choose from it according to the kinds of stone and need .

HOW TO USE THE ABRASIVE BRUSH RIGHTLY? Adding water during the grinding . Prevented the high hig h temperature making the filaments changing shape during the filaments friction in high speed .As the the sequence of the number of abrasive brush from from thick to thin ,the pressure ’

working on the grind should from big to small. It s logical for the skip . Reducing the middle step excessively will affect the effect of grinding ,other size it will add the cost .Using the steel brush as possible. The abrasive brush as the first step could reduce the loss for the rough surface to abrasive filaments, extended the life of the abrasive brush.

WHY ADOPT LOW DENSITY FILAMENTS? ’

For the abrasive brush we should talk about three density ,it s the filaments on the abrasive brush (craft density) the th e silicon carbide ca rbide grit in the filaments and nylon density as the silicon sili con carbide (material density).the first and the second sec ond density should have the logical ,and not much higher is much better ;and nylon density shou ld have the basic of top quality ,lower the density -reducing the unit weight of the filaments, reducing the cost of material.



Technical of Our Diamond Tools

Recommend Documents