LTE RF/RAN Key Performance Indicators KPI Name S.No E-RAB Setup Success Ratio
1 Initial E-RAB Setup Success Ratio
2 Additional E-RAB Setup Success Ratio
3 4 E-RAB Setup Attempts E-RAB Setup Failure Ratio due to Radio Network Layer Failure 5 E-RAB Setup Failure Ratio due to Transport Layer Failure 6 E-RAB Setup Failure Ratio due to Resource Failure 7 E-RAB Setup Failure Ratio due Other Failure 8 S1 Initial Context Setup Success Ratio 9 10 S1 Initial Context Setup Attempts S1 Initial Context Setup Failure Ratio due to Radio Network Layer Failure 11 S1 Initial Context Setup Failure Ratio due to Transport Layer Failure 12 S1 Initial Context Setup Failure Ratio due to Resource Failure 13 S1 Initial Context Setup Failure Ratio due Other Failure 14 S1 Setup Success Ratio
15 16 S1 Setup Attempts S1 Setup Failure Ratio due to No Response Failure 17
S1 Setup Failure Failure Ratio due to MME Failure 18 UE Context Modification Failure Rate
19 20 Data Radio Bearer Attempts Data Radio Bearer Setup Success Ratio
21 Radio Bearer Drop Ratio
22 Radio Bearer Success Ratio 23 RRC Connection Setup Attempts due to MO Signaling
24 RRC Connection Setup Attempts due to MT- Access
25 RRC Connection Setup Attempts due to MO-Data
26 RRC Connection Setup Attempts due to others
27 RRC Connection Setup Attempts due to emergency calls
28
RRC Connection Setup Success Ratio
29 E-UTRAN RRC Connection Setup Success Ratio for emergency Calls 30 RRC Connection Failure Ratio due to RRC timer expiry
31 RRC Connection Failure Ratio due to RRC protocol error
32 RRC Connection Failure Ratio due to radio access control f ailure
33 RRC Connection Failure Ratio due to lack of RBs for emergency calls
34 RRC Paging Discard Ratio 35 36 RRC Paging Records E-RAB Drop Ratio, RAN View
37 E-RAB drop ratio due to radio network layer (RNL) cause initiated by eNB
38
E-RAB drop ratio due to transport network layer (TNL) cause initiated by eNB
39 E-RAB drop ratio due to other (OTH) cause initiated be eNB
40 E-RAB drop ratio due to radio network layer (RNL) cause initiated by EPC
41 E-RAB drop ratio due to other (OTH) cause initiated be EPC
42 E-RAB Normal Release Ratio, User Perspective
43
E-RAB Normal Release Ratio, RAN View
44 E-RAB Setup Failure Ratio due to radio network la yer failure (RNL) 45 E-RAB Setup Failure Ratio due to transport layer failure (TRPORT) 46 E-RAB Setup Failure Ratio due to resource failure (RESOUR) 47 E-RAB Setup Failure Ratio due to other failure (OTH) 48 E-RAB Drop Ratio, User Perspective
49 S1 Initial Context Setup Failure Ratio due to 50 failure (RNL) S1 Initial Context Setup Failure Ratio due to 51 failure TRPORT S1 Initial Context Setup Failure Ratio due to 52 RESOUR S1 Initial Context Setup Failure Ratio due to 53
radio network layer radio transport layer resource failure other failure (OTH)
S1 Setup Failure Ratio due to "no response" failure 54 S1 Setup Failure Ratio due to "MME" failure 55 IP incoming Traffic Error Ratio 56 Average Latency Downlink 57
Average Latency Downlink for QCI1 DRBs 58 Average Latency Downlink for non-GBR DRBs
59 Average Latency Uplink
60 RLC PDU Re-transmission Ratio Downlink 61 RLC PDU Re-transmission Ratio Uplink 62 Average RSSI for PUCCH 63 Average RSSI for PUSCH 64 Average SINR for PUCCH 65 Average SINR for PUSCH 66 Average CQI
67 Average CQI Offset 68
HO Preparation Success Ratio, intra eNB
69 HO Preparations, intra eNB 70 HO Preparation Failure Ratio due to admission control failure, intra eNB 71 HO Preparation Failure Ratio due to other failure, intra eNB
72 HO Success Ratio, intra eNB 73 74 HO Attempts, intra eNB HO Failure Ratio, intra eNB
75 Total HO Success Ratio, intra eNB
76 HO Preparation Success Ratio, inter eNB X2 based
77 HO Preparation, inter eNB X2 based 78 HO Preparation Success Ratio, inter eNB S1 based
79 HO Preparation, inter eNB S1 based 80 HO Preparation Failure Ratio due to timer failure, inter eNB X2 based
81 HO Preparation Failure Ratio due to admission control failure,inter eNB X2 based
82
HO Preparation Failure Ratio due to other failure, inter eNB X2 based
83 HO Preparation Failure Ratio due to "timer TS1RELOCprep" failure, Inter eNB S1 based
84 HO Preparation Failure Ratio due to percentage of "lack of resources" failure , Inter eNB S1 based
85 HO Preparation Failure Ratio due to percentage of "other" failure , Inter eNB S1 based
86 HO Success Ratio, inter eNB X2 based
87 HO Attempts, inter eNB X2 based 88 HO Success Ratio, inter eNB S1 based
89 HO Attempts, inter eNB S1 based 90 HO Failure Ratio, inter eNB X2 ba sed
91 HO Failure Ratio, inter eNB S1 based
92 Total HO Success Ratio, inter eNB X2 based
93
Total HO Success Ratio, inter eNB S1 based
94 CS Fallback Attempts with Redirection via RRC Connection Release Distribution Rate for UE in Connected mode 95 CS Fallback Attempts with Redirection via RRC Connection Release Distribution Rate for UE in Idle mode 96 CS Fallback Attempts with Redirection via RRC Connection Release Distribution Rate for Emergency call reason 97 Inter-Frequency HO Success Ratio
98 Inter-Frequency HO Success Ratio - Measurement Gap assisted
99 Average PDCP Layer Cell Throughput Downlink 100 Average PDCP Layer Cell Throughput Downlink for QCI1 DRBs 101 Average PDCP Layer Cell Throughput Uplink 102 Average PDCP Layer Cell Throughput Uplink for QCI1 DRBs 103 Average RLC Layer Cell Throughput Downlink 104 Average RLC Layer Cell Throughput Uplink 105 Average incoming Signaling Throughput on X2 106 Average outgoing Signaling Throughput on X2 107 Average incoming Data Throughput on X2 108 Average outgoing Data Throughput on X2 109
Average PRB usage per TTI Downlink
110 Average PRB Usage per TTI Uplink 111 Cell Availability Ratio 112 Planned Cell Unavailability Ratio 113 Unplanned Cell Unavailability Ratio
114 Cell Availability, excluding blocked by user state (BLU) 115 Average Active UEs with data in the buffer per cell DL 116 Average Active UEs with data in the buffer for QCI1 DRBs per cell DL 117 Average Active UEs with data in the buffer for non-GBR DRBs per cell DL 118 Average Active UEs with data in the buffer per cell UL 119 Average Active UEs with data in the buffer for QCI1 DRBs per cell UL 120 Average Active UEs with data in the buffer for non-GBR DRBs per cell UL 121 Maximum Active UEs with data in the buffer per cell DL 122 Maximum Active UEs with data in the buffer per cell UL 123 Average Active UEs per eNB 124 IP incoming Traffic Volume 125 IP outgoing Traffic Volume 126 IP incoming Traffic Throughput
127
IP outgoing Traffic Throughput
128 IP incoming Traffic Error Ratio 129 Service Accessibility Ratio[%] 130 Completed Session Ratio[%] 131 Service Access Time [s] 132 Session Time [s] 133 Single User Data Rate [Mbps] 134 VoIP Call Setup Time [s]
135 VoIP Call Success Rate [%]
136 VoIP Call Drop Rate [%]
137 Speech Quality [MOS-CQ] 138 One-way Voice Delay (m2e) [ms]
139 Voice Frame Error Rate (FER) [%]
140 Voice Interrupt Time (HO) 141
VoIP Capacity per Cell [n]
142 Attach Time [ms]
143 Detach Time [ms]
144 Attach Success Rate [%]
145 Service Request (EPS) Time [ms] UE I nitiated
146 Service Request (EPS) Time [ms] Network Initiated
147 Service Request (EPS) Success Rate[%]
148 Service (EPS) Drop Rate [%]
149
Handover Procedure Time [ms]
150 Handover Success Rate [%] 151 Paging Time [ms]
152 Paging Failure Rate [%]
153 (LTE) Round Trip Time (RTT) [ms]
154 (LTE) Single User Data Rate [Mbps]
155 (LTE) Packet Loss Rate (PLR) [%]
156 (LTE) Service Interrupt Time (HO) [ms]
157 (RB) Packet Loss Rate UL / DL [%] 158
(RB) Single User Data Rate [Mbps]
159 Cell Throughput [Mbps]
160 (RB)Residual Block Error Rate(Residual BLER) 161 162 One Round Paging Sucess One round Tracking Area Update success 163 SAE Bearer Setup Success Rate 164 165 Call Drop Rate 166 Intra LTE Handover Success Rate
KPI Description
KPI Category
The KPI describes the setup success ratio of the elementary E-RAB setup procedure used to setup the E-RAB between MME and UE.It indicates the E-UTRAN contribution to network accessibility for the end-user not the whole end-to-end service accessibilit . The KPI describes the setup success ratio of the elementary initial E-RAB setup procedure.It indicates the E-UTRAN contribution to network accessibility for the end-user, not the whole end-to-end service accessibilit . The KPI describes the setup success ratio of the elementary additional ERAB setup procedure.It indicates the E-UTRAN contribution to network accessibility for the end-user, not the whole end-to-end service accessibility.
Accessibility
The KPI describes the number of E-RAB Setup Attempts.
Accessibility
This KPI describes the ratio of a specific f ailure cause related to all EPS Bearer set up attempts This KPI describes the ratio of a specific f ailure cause related to all EPS Bearer set u attem ts This KPI describes the ratio of a specific f ailure cause related to all EPS Bearer set up attempts This KPI describes the ratio of a specific f ailure cause related to all EPS Bearer set up attempts The KPI shows the setup success ratio for the elementary procedure "Initial Context Setup", used to set up the initial UE context in MME UE-associated lo ical S1-connection . The KPI shows the number of S1 Initial Context Setup Attempts
Retainability
Accessibility
Accessibility
Retainability Retainability Retainability Accessibility
Accessibility
This KPI describes the ratio of a specific f ailure cause related to all initial context setup attempts.
Retainability
This KPI describes the ratio of a specific f ailure cause related to all initial context setup attempts.
Retainability
This KPI describes the ratio of a specific f ailure cause related to all initial context setup attempts.
Retainability
This KPI describes the ratio of a specific f ailure cause related to all initial context setup attempts.
Retainability
The KPI shows the setup success ratio for the elementary procedure "S1 Setup". When this procedure is finished, S1 interface is operational and other S1 messages can be exchanged
Accessibility
The KPI shows the number of S1 Setup Attempts.
Accessibility
This KPI describes the ratio of a specific S1 setup failure cause related to all S1 setu attem ts.
Retainability
This KPI describes the ratio of a specific S1 setup failure cause related to all S1 setu attem ts. The KPI is used to indicate some problems with UE Context Modification procedure (e.g. due to security reason, ENB does not support either requested modification or CS Fallback feature . The KPI shows the Data Radio Bearer Attempts. The KPI shows the setup success ratio for the data radio bearer setup procedure. The elementary procedure "RRC connection reconfiguration" is used in this context to setup a user plane data radio bearer. The KPI shows the ratio of dropped Radio Bearers
Retainability Accessibility
Accessibility Accessibility
Retainability
The KPI shows the Radio Bearer Success Ratio given as 100 - Radio Bearer Drop Ratio
Retainability
The KPI shows the RRC Connection Setup Attempts on a per cause basis.The RRC connection requests for emergency calls may be also counted by some of the remaining KPIs within this chapter. However for emergency calls it is mandatory to provide also a separate KPI to monitor
Accessibility
The KPI shows the RRC Connection Setup Attempts on a per cause basis.The RRC connection requests for emergency calls may be also counted by some of the remaining KPIs within this chapter. However for emergency calls it is mandatory to provide also a separate KPI to monitor
Accessibility
The KPI shows the RRC Connection Setup Attempts on a per cause basis.The RRC connection requests for emergency calls may be also counted by some of the remaining KPIs within this chapter. However for emergency calls it is mandatory to provide also a separate KPI to monitor
Accessibility
The KPI shows the RRC Connection Setup Attempts on a per cause basis.The RRC connection requests for emergency calls may be also counted by some of the remaining KPIs within this chapter. However for emergency calls it is mandatory to provide also a separate KPI to monitor
Accessibility
The KPI shows the RRC Connection Setup Attempts on a per cause basis.The RRC connection requests for emergency calls may be also counted by some of the remaining KPIs within this chapter. However for emergency calls it is mandatory to provide also a separate KPI to monitor
Accessibility
The KPI shows the setup success ratio for the elementary procedure "RRC connection establishment" used to set up a radio connection from UE to eNB (involves SRB1 establishment).
Accessibility
The KPI shows the setup success ratio for the elementary procedure "RRC connection establishment" used to set up a radio connection from UE to eNB for emer enc calls. This KPI describes the ratio of a specific RRC connection setup failure cause related to all RRC connection requests
Accessibility
This KPI describes the ratio of a specific RRC connection setup failure cause related to all RRC connection requests
Retainability
This KPI describes the ratio of a specific RRC connection setup failure cause related to all RRC connection requests
Retainability
This KPI describes the ratio of a specific RRC connection setup failure cause related to all RRC connection requests
Retainability
This KPI describes the paging request discard ratio on RRC level
Accessibility
This KPI shows the numbe rof RRC Paging Paging Records
Accessibility
This KPI describes the ratio of abnormally released (dropped) E-RABs from RAN point of view
Retainability
This KPI describes the ratio of abnormally released (dropped) E-RABs from RAN point of view
Retainability
Retainability
This KPI describes the ratio of abnormally released (dropped) E-RABs from RAN point of view
Retainability
This KPI describes the ratio of abnormally released (dropped) E-RABs from RAN point of view
Retainability
This KPI describes the ratio of abnormally released (dropped) E-RABs from RAN point of view
Retainability
This KPI describes the ratio of abnormally released (dropped) E-RABs from RAN point of view
Retainability
This KPI describes the ratio of normally released E-RABs from user perspective. This KPI is corresponding to a Connection Completion Ratio
Retainability
This KPI describes the ratio of normally released E-RABs from RAN point of view.
Retainability
This KPI describes the ratio of a specific f ailure cause related to all all EPS EPS Bea Beare rerr set set u atte attem m ts This KPI describes the ratio of a specific f ailure cause related to all all EPS EPS Bea Beare rerr set set u atte attem m ts This KPI describes the ratio of a specific f ailure cause related to all EPS Bearer set up a ttempts This KPI describes the ratio of a specific f ailure cause related to all EPS Bearer set up a ttempts This KPI describes the ratio of abnormally released (dropped) E-RABs from user perspective point of view
Retainability
This KPI describes the ratio of a specific f ailure cause related to all initial context setup attempts This KPI describes the ratio of a specific f ailure cause related to all initia initiall cont context ext setu setu attem attem ts This KPI describes the ratio of a specific f ailure cause related to all initia initiall cont context ext setu setu attem attem ts This KPI describes the ratio of a specific f ailure cause related to all initial context setup attempts This KPI describes the ratio of a specific S1 setup failure cause related to all S1 setup attempts This KPI describes the ratio of a specific S1 setup failure cause cause relate related d to to all all S1 S1 setu setu attem attem ts This KPI shows the error ratio for IP based incoming traffic
Retainability
This KPI shows the retention period (delay) of a PDCP SDU (DL) inside eNB. Time from reception of an IP packet to the transmission of the first acket over the Uu interface
Retainability
Retainability Retainability Retainability
Retainability Retainability Integrity/Quality
This KPI shows the retention period (delay) of a PDCP SDU (DL) inside eNB for QCI1 DRBs. Time from reception of IP acket to transmission of first acket over the Uu interface This KPI shows the retention period (delay) of a PDCP SDU (DL) inside eNB for non-GBR DRBs (QCI5..9). Time from reception of IP packet to transmission of first pack et over the Uu interface This KPI shows the retention period (delay) of a PDCP SDU (UL) inside eNB. Time starting at the arrival of the PDCP SDU in the eNB and ending at the first transmission of a packet over over S1 contai containin nin a se ment ment of the SDU This KPI shows the retransmission ratio for RLC PDUs in downlink direction
Integrity/Quality
This KPI shows the retransmission ratio for RLC PDUs in uplink direction.
Integrity/Quality
This KPI shows the average Received Signal Strength Indicator (RSSI) value for physical UL control channel (PUCCH), measured in the eNB This KPI shows the average Received Signal Strength Indicator (RSSI) value for physical UL shared channel (PUSCH), measured in the eNB This KPI shows the Signal to Interference and Noise Ratio (SINR) for the physical UL control channel (PUCCH), measured in the eNB This KPI shows the Signal to Interference and Noise Ratio (SINR) for the physical UL shared channel (PUSCH), measured in the eNB This KPI shows the average UE reported Channel Quality Indicator (CQI) value
Integrity/Quality
This KPI shows the average eNB used offset (correction) value for Channel Channel Qualit Indicators Indicators CQI
Integrity/Quality
Integrity/Quality
Integrity/Quality
Integrity/Quality
Integrity/Quality
Integrity/Quality
Integrity/Quality
Integrity/Quality
This KPI describes the success ratio for the handover preparation phase, when the source eNB attempts to prepare resources and finally starts to attempt the handover to a neighboring cell within the own eNB
Mobility
This KPI shows the total number of intra eNB HO preparations
Mobility
This KPI describes the ratio of a specific intra eNB handover preparation failure cause related to total number of intra eNB HO preparations. The source eNB f ails to prepare resources for the handover to a nei hborin cell within the own eNB. This KPI describes the ratio of a specific intra eNB handover preparation failure cause related to total number of intra eNB HO preparations. The source eNB f ails to prepare resources for the handover to a nei hborin cell within the own eNB. This KPI describes the success ratio for the handover execution phase, when the source eNB receives information that the UE successfull is connected to the tar et cell within own eNB This KPI shows the numbe rof intra eNB handover attempts
Mobility
Mobility
Mobility
This KPI describes the ratio of failed intra eNB handovers related to all attempted intra eNB handovers. This KPI represents the case of a failed Handover when all UE resources are still allocated for the UE
Mobility
This KPI describes the total intra eNB HO Success Ratio from the HO preparation start until the successful HO execution
Mobility
This KPI describes the success ratio for the inter eNB X2 based handover preparation phase, when the source eNB attempts to prepare resources and finally starts to attempt the handover to a neighboring cell in a target eNB
Mobility
This KPI shows the numbe rof inter eNB X2 based HO preparations
Mobility
This KPI describes the success ratio for the inter eNB S1 based handover preparation phase, when the source eNB attempts to prepare resources and finally starts to attempt the handover to a neighboring cell in a target eNB
Mobility
This KPI shows the numbe of inter eNb S1 based HO preparations
Mobility
This KPI describes the ratio of a specific inter eNB X2 based handover preparation failure cause related to total number of inter eNB X2 based HO preparations. The source eNB fails to prepare resources for the handover to a neighboring cell in a
Mobility
This KPI describes the ratio of a specific inter eNB X2 based handover preparation failure cause related to total number of inter eNB X2 based HO preparations. The source eNB fails to prepare resources for the handover to a neighboring cell in a
Mobility
This KPI describes the ratio of a specific inter eNB X2 based handover preparation failure cause related to total number of inter eNB X2 based HO preparations. The source eNB fails to prepare resources for the handover to a neighboring cell in a
Mobility
This KPI describes the ratio of a specific inter eNB S1based handover preparation failure cause related to total number of inter eNB S1 based HO preparations. The source eNB fails to prepare resources for the handover to a neighboring cell in a
Mobility
This KPI describes the ratio of a specific inter eNB S1based handover preparation failure cause related to total number of inter eNB S1 based HO preparations. The source eNB fails to prepare resources for the handover to a neighboring cell in a tar et eNB This KPI describes the ratio of a specific inter eNB S1based handover preparation failure cause related to total number of inter eNB S1 based HO preparations. The source eNB fails to prepare resources for the handover to a neighboring cell in a tar et eNB This KPI describes the success ratio for the inter eNB X2 based handover execution phase, when the source eNB receives information that the UE successfully is connected to the tar et cell within tar et eNB This KPI the number of inter eNB X2 based HO attempts
Mobility
This KPI describes the success ratio for the inter eNB S1 based handover execution phase, when the source eNB receives information that the UE successfully is connected to the tar et cell within tar et eNB This KPI shows the number of inetr eNB S1 based HO attempts This KPI describes the ratio of failed inter eNB X2 based handoversrelated to all attempted inter eNB handovers. This KPI represents the case of a failed Handover when all UE resources are still allocated for the UE This KPI describes the ratio of failed inter eNB S1 based handovers related to all attempted inter eNB handovers. This KPI represents the case of a failed Handover when all UE resources are still allocated for the UE This KPI describes the total inter eNB HO Success Ratio from the HO preparation start until the successful HO execution
Mobility
Mobility
Mobility Mobility
Mobility Mobility
Mobility
Mobility
This KPI describes the total inter eNB S1 based HO Success Ratio from HO preparation start until successful HO execution
Mobility
This KPI describes the ratio of a specific C S Fallback Attempts related to all CS Fallback Attempts with redirection via RRC Connection Release This KPI describes the ratio of a specific C S Fallback Attempts related to all CS Fallback Attempts with redirection via RRC Connection Release This KPI describes the ratio of a specific C S Fallback Attempts related to all CS Fallback Attempts with redirection via RRC Connection Release This KPI describes the success ratio for the inter-frequency HO, when the source eNB receives information that the UE successfully is connected to the target cell within target eNB. The KPI is defined independent of the network topology (intra eNB HO inter eNB HO and of the usa e of measurement a s This KPI describes the success ratio for inter-frequency HO when measurement gaps are configured for the UE, when the source eNB receives information that the UE successfully is connected to the target cell within target eNB. The KPI is defined independent of the network topology (intra eNB HO /
Mobility
This KPI shows the average PDCP layer throughput per cell in downlink direction This KPI shows the average PDCP layer throughput per cell in downlink direction for QCI1 DRBs This KPI shows the average PDCP layer throughput per cell in u link direction This KPI shows the average PDCP layer throughput per cell in uplink direction for QCI1 DRBs This KPI shows the average RLC layer throughput per cell in downlink direction This KPI shows the average RLC layer throughput per cell in u link direction This KPI shows the average incoming signaling throughput on X2AP layer per eNB This KPI shows the average outgoing signaling throughput on X2AP layer per eNB
Usage
This KPI shows the average incoming user plane data throughput on X2AP la er er eNB This KPI shows the average outgoing user plane data throughput on X2AP la er er eNB
Usage
Mobility
Mobility
Mobility
Mobility
Usage Usage Usage Usage Usage Usage Usage
Usage
This KPI shows the average value of the Physical Resource Block (PRB) utilization per TTI in downlink direction. The utilization is defined by the ratio of used to available PRBs per TTI
Usage
This KPI shows the average value of the Physical Resource Block (PRB) utilization per TTI in uplink direction. The utilization is defined b the ratio of used to available PRBs er TTI This KPI shows the ratio of services in a cell being available for end-users
Usage
This KPI shows the ratio of services in a cell being planned unavailable for end-users
Usage
This KPI shows the ratio of services in a cell being unplanned unavailable for end-users
Usage
This KPI shows Cell Availability, excluding blocked by user state (BLU)" that gives the percent of available time over time that should be available This KPI shows the average number of UE's having data in RLC level buffers during the measurement period per cell for downlink direction This KPI shows the average number of UE's having data in RLC level buffers for DRBs of QCI1 during the measurement eriod er cell for downlink direction This KPI shows the average number of UE's having data in RLC level buffers for non-GBR DRBs during the measurement eriod er cell for downlink direction This KPI shows the average number of UE's having data in RLC level buffers during the measurement period per cell for u link direction. This KPI shows the average number of UE with buffered data in UL per logical channel group id mapped to VoIP (QCI1) DRBs durin a measurement eriod er cell This KPI shows the average number of UE with buffered data in UL per logical channel group id mapped to non-GBR DRBs durin a measurement eriod er cell This KPI shows the maximum number of UE's having data in RLC level buffers during the measurement period per cell for downlink direction This KPI shows the maximum number of UE's having data in RLC level buffers during the measurement period per cell for u link direction This KPI shows the average number of UE's having one SRB and at least one DRB during the measurement period per eNB This KPI shows the total data volume for IP based Traffic in incoming direction This KPI shows the total data volume for IP based Traffic in outgoing direction This KPI shows the total throughput for IP based traffic in incoming direction
Usage
Usage
Usage
Usage
Usage
Usage
Usage
Usage
Usage
Usage
Usage Usage Usage Usage
This KPI shows the total throughput for IP based traffic in outgoing direction
Usage
This KPI shows the error ratio for IP based incoming traffic
Retainability
The service accessibility ratio denotes the probability that the user can establish the necessary bearer (EPS) and access the FTP service successfull The completed session ratio is the proportion of completed FTP sessions and sessions that were started successfully It is the time period needed to access the FTP service successfully,from starting the ftp client to the point of time when the first data packet is sent or received It is the overall duration of the download or upload of reference files from / to the FTP server After the connection to the FTP server has been successfully established, the parameter describes the average data transfer rate measured over the data transfer hase Two alternatives are defined, one being the Post-dial Delay, the other the complete VoIP Session Setup Time.The Post-dial Delay of a VoIP call is defined as the elapsed time between requesting a connection and receiving the first ring tone from the network.The full Session Setup procedure is defined between requesting a connection by the inviting user and receiving a positive response from the called party in a one phase IETF or in a 3-phase 3GPP compliant call setup procedure
Accessibility
Reliability Latency
Latency Throughput
Latency
It is the probability of successful VoIP call establishments, calculated as the Accessibility proportion of successful VoIP call setup requests and all call establishment attempts. The VoIP call is not successful if a predefined timer threshold expires, or a network failure inhibited the session setup.Failures due to authentication or authorization errors or to wrong parameter settings are excluded. It is the percentage of dropped calls against all successfully established Reliability calls. It reflects the probability that a VoIP session gets aborted due to some network error. Insufficient network resources are also seen as errors b the end-user. End-user perceived speech quality expressed as conversational MOSIntegrity/Quality CQ(MeanOpinion Score) and R factor value The traversal time of a spoken syllable from the mouth of the speaker to the ears of the listener. It is commonly called mouth-to-ear (m2e) delay.M2e delay values are distinguished for MOC, MTC, and MMC scenarios. The other party in MOC, MOT calls is a fixed VoIP user.
Latency
Ratio of voice frames lost, or received with error and o f the total number of voice frames sent during the call. Measured in loaded and unloaded network, under different radio conditions. Stationary and mobile user.
Reliability
Discontinuity of voice media flow (also called “voice gap”) due to handover in UL and DL directions.
Latency
The maximum number of concurrent VoIP calls that can be supported by Throughput the cell with good voice quality for at least 95% of all users. Voice quality is considered to be good if MOS_CQ ≥ 3.6 during the call. With Attach, the mobile terminal registers at the LTE network. At the Latency end of the procedure the UE is authenticated, and a default (nGBR) bearer is established.The Attach Time is the interval between the connection request and the acknowledgement of the positive response by the UE
With an explicit Detach request the UE informs the LTE network that it Latency does not want to access the EPS a ny longer. At the end of the procedure all EPS bearers of the UE are released. The Detach Time is the interval between the Detach Request and the reception of a Detach Accept message by the UE. No Detach Accept is sent by the network if the cause for Detach is switching the UE off. The Attach Success Rate is defined as the ratio between the number of Accessibility successful registrations and the number of a ll requests. This is the probability that a user can attach to the LTE network at any moment of time. It is the time taken by the LTE network to setup an EPS bearer on Latency request by the UE. The EPS bearer can be new (dedicated), or an existing one (e.g. the default EPS bearer). The latter is needed to reassign Uu radio and S1 bearer resources to the existing EPS bearer of a previously It is the time taken by the LTE network to set up an EPS bearer on request by the P-GW. The EPS bearer has to be created before IP packets can be sent (DL) to the UE if the UE has no proper EPS bearer for the given IP packet flow. The network initiated Service Request Time includes a Paging Time if the UE is idle
Latency
This KPI is defined as the ratio between successfully established EPS Accessibility bearers compared to the overall number of EPS bearer establishment attempts. It corresponds to the probability that a user or the LTE network can establish an EPS bearer at a ny moment in time. Requests that are terminated by timer expiry (due to the unaccessibility of some LTE resource) are considered as unsuccessful attempts.
It is the ratio between abnormally released bearers and the overall number of established EPS bearers. An abnormal release is defined as any EPS bearer termination that was not triggered by the mobile user(from UE side). Thus, it reflects the probability that an established bearer is aborted due to insufficient network resources. Dropping the bearer becomes visible to the end-user if an application service is actively using it. If the application a utomatically re-establishes the bearer, it remains unnoticed by the user.
Reliability
It denotes the total time needed for the hand-over procedure as seen by the UE. It begins by receiving a Handover Command from the SeNB and ends by sending the Handover Confirm response to the TeNB by the UE. Its relevance is the discontinuity of the IP packet flow in the user plane that is implied by it(also called service interruption). The value of the HO Procedure Time KPI depends on the hand-over scenario. The following HO scenarios are distinguished (though not directly seen by the UE).
Mobility
The Handover Success Rate is the ratio between successfully executed (committed)HO procedures and the number of all Handover attempts.
Mobility
It denotes the total procedure time from starting the paging request in DL and terminating it with the subsequent service request (EPS bearer setup) of the UE after it has been located. Thus, the paging time is per definition the difference between network and UE initiated Service Request Times.
Latency
The Paging Failure Rate is the ratio between unsuccessful paging requests and the number of all paging attempts initiated by the MME.Retries of the same paging request by the MME are not counted as new attempts. Similarly, multicasting the same request to more than one eNBs (in the UE´s tracking areas) is considered as one attempt
Accessibility
RTT in UL is the interval between sending a datagram by the UE & receiving the corresponding reply from an IP peer entity connected to the Gi interface of the P-GW. RTT in DL is the interval between sending a datagram to the UE & receiving the corresponding reply by the IP host
Latency
The metric describes the data speed available to one user of the LTE network on UDP/IP level. It is given as the maximum (95%-ile) value that can be observed over a short period of time (e.g. of 1s) and as a mean value that characterizes longer data transfer periods (minutes). Its value distribution over the radio cell is given as a f unction of the SINR. The maximum value is often referred to in the literature as instantaneous "Peak Throughput" that is achieved in optimal radio conditions. The user data rate can be given for a single user active in the cell (single user data rate), or to one of several concurrently active users.
Throughput
This is the ratio between the numbers of lost or corrupted IP pack ets,and of all IP packets sent. Corrupted IP packets are those that contain bit errors in their headers or in their payload.Packets with "residual", i.e.undetected errors are not counted as lost The Service Interrupt Time is the interval between the last sent/received IP packet of a continuous UL/DL data stream in the old cell and the first sent/received user IP packet in the new cell measured on the UE (also called "user plane break"). The value of the KPI depends of the handover scenario
Reliability
This is the ratio between the numbers of lost or corrupted IP pack ets,and of all IP packets sent. Corrupted IP packets are those that contain bit errors in their headers or in their a load
Reliability
Mobility
The metric describes the UDP/IP data rate achievable by one user. It can be given as single user data rate if only one user is active in the cell, or as multi-user data rate for a given number of concurrently active users.
Throughput
The metric shows the sustainable aggregate throughput of the cell (in Throughput UL/DL)available to "n" stationary users distributed uniformly in the cell and running a typical mix of applications. The "cell throughput" is the sum of all bits transported in all radio blocks carrying PDUs (i.e. bits in UL-SCH / DL-SCH transport blocks) during one second. The cell capacity is also given as peak value(called peak cell ca pacity, or throughput), which is defined as the aggregate throughput of "n" users all located in best radio conditions. The cell throughput value is defined here on PHY level, but could be given for other protocol levels(UDP/IP, PDCP, RLC, MAC), too. When the (peak, average) cell throughput is expressed on UDP/IP level, it corresponds to the (peak, mean) user data rate value at comparable radio conditions It is the ratio between the numbers of lost or corrupted radio blocks, and of all blocks sent. Corrupted radio blocks a re those with bit errors. One time paging success ratio One time TAU success ratio Success ratio for SAE bare established The call drop caused by poor RF coverage Handover within the same MME/S-GW(between eNB)
Reliability
KPI Logical Formula E-RAB SSR=(E-RAB setup successes / E-RAB setup attempts)*100%
E-RAB ISSR=(intial E-RAB setup successes / initial E-RAB setup attempts)*100%
E-RAB ASSR=(additional E-RAB setup successes / additional E-RAB setup attempts)*100%
sum([EPS_BEARER_SETUP_ATTEMPTS]) E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attempts)*100% E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attem ts *100% E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attempts)*100% E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attempts)*100% S1 init Cont SSR=(initial context setup successes / initial context setup attempts)*100% S1 init Cont SAtt= initial context setup attempts S1 init Cont SFRCause=(initial context setup failure_x / initial context setup attempts)*100% S1 init Cont SFRCause=(initial context setup failure_x / initial context setup attempts)*100% S1 init Cont SFRCause=(initial context setup failure_x / initial context setup attempts)*100% S1 init Cont SFRCause=(initial context setup failure_x / initial context setup attempts)*100% S1 SSR=(S1 setup successes / S1 setup attempts)*100%
S1 SattR = S1 setup attempts S1 SFRCause=(S1 setup failure_x / S1 setup attempts)*100%
S1 SFRCause=(S1 setup failure_x / S1 setup attempts)*100% UE Con Mod Fail rate =(UE_CONTEXT_MOD_FAIL / UE Con Mod Atts) * 100%
DATA_RB_STP_ATT = DATA_RB_STP_ATT DRB SSR=(DRB setup successes / DRB setup attempts)*100%
RB DR=(abnormal RB releases / total RB releases)*100%
RB SR= 100 - RB DR
SIGN_CONN_ESTAB_ATT = SIGN_CONN_ESTAB_ATT_x
SIGN_CONN_ESTAB_ATT = SIGN_CONN_ESTAB_ATT_x
SIGN_CONN_ESTAB_ATT = SIGN_CONN_ESTAB_ATT_x
SIGN_CONN_ESTAB_ATT = SIGN_CONN_ESTAB_ATT_x
SIGN_CONN_ESTAB_ATT = SIGN_CONN_ESTAB_ATT_x
RCC Con SSR=(RRC connection setup completions / RRC connection requests)*100%
RCC Con SSR EMG=(RRC connection setup completions for emergency calls / RRC connection requests for emergency calls *100% S1 SFR=(RRC connection setup failure_x / RRC connection requests)*100%
S1 SFR=(RRC connection setup failure_x / RRC connection requests)*100%
S1 SFR=(RRC connection setup failure_x / RRC connection requests)*100%
S1 SFR=(RRC connection setup failure_x / RRC connection requests)*100%
Paging DCR=(discarded RRC paging records / transmitted RRC a in records *100% Paging Records = transmitted RRC paging records E-RAB DR RAN=(abnormal E-RAB release requests / all ERAB release commands)*100%
E-RAB DRCause=(abnormal E-RAB release request_x / all E-RAB release commands)*100%
E-RAB DRCause=(abnormal E-RAB release request_x / all E-RAB release commands)*100%
E-RAB DRCause=(abnormal E-RAB release request_x / all E-RAB release commands)*100%
E-RAB DRCause=(abnormal E-RAB release request_x / all E-RAB release commands)*100%
E-RAB DRCause=(abnormal E-RAB release request_x / all E-RAB release commands)*100%
E-RAB NRR UP=(normal E-RAB releases user perspective / all E-RAB releases)*100%
E-RAB NRR RAN=(normal E-RAB releases RAN view/ all ERAB releases)*100%
E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attem ts *100% E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attem ts *100% E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attempts)*100% E-RAB SFRCause=(E-RAB setup failure_x / E-RAB setup attempts)*100% E-RAB DR UP=(abnormal E-RAB release requests, user perspective/ all E-RAB releases )*100%
S1 init Cont SFRCause=(initial context setup failure_x / initial context setup attempts)*100% S1 init Cont SFRCause=(initial context setup failure_x / initial context setu attem ts *100% S1 init Cont SFRCause=(initial context setup failure_x / initial context setu attem ts *100% S1 init Cont SFRCause=(initial context setup failure_x / initial context setup attempts)*100% S1 SFRCause=(S1 setup failure_x / S1 setup attempts)*100% S1 SFRCause=(S1 setup failure_x / S1 setup attem ts *100% IP IN ER = (incoming erroneous IP packets) / total incomin IP ackets LatencyAvgDL = PDCP SDU delay on DL DTCH Mean
LatencyAvgDL=PDCP SDU delay on DL DTCH Mean for QCI1 DRBs LatencyAvgDLnonGBR=PDCP SDU delay on DL DTCH Mean for non GBR DRBs
LatencyAvgUL = PDCP SDU delay on UL DTCH Mean
DL RLC PDU ReTrR = (number of retrans. RLC PDUs) / number all trans RLC PDUs UL RLC PDU ReTrR = (number of received duplicated RLC PDUs) / number all received RLC PDUs AVG RSSI PUCCH= average of measured RSSI values for PUCCH AVG RSSI PUSCH = average of measured RSSI values for PUSCH AVG SINR PUCCH= average of measured SINR values for PUCCH AVG SINR PUSCH= average of measured SINR values for PUSCH AVG CQI= sum(number of hits in class_x * x) / sum(total number of hits over all classes)x = 0, …, 15
AVG CQI Offset= average of measured CQI offset values
Intra HO prep SR =(number of successful intra eNB HO prep)/ (total number of intra enB HO preparations)*100%= (number of intra eNB HO attempts) / (total number of intra eNB HO preparations)*100% Intra HO preps = (total number of intra eNB HO preparations) Intra HO prep FRCause =(number of intra eNB HO prep failure_x) / (total number of intra enB HO preparations)*100%
Intra HO prep FRCause =(number of intra eNB HO prep failure_x) / (total number of intra enB HO preparations)*100%
Intra HO SR =(number of successful intra eNB HOs) / (number of intra eNB HO attempts)*100% Intra HO Att =(number of intra eNB HO attempts) Intra HO FR =(number of unsuccessful intra eNB HOs) / (number of intra eNB HO attempts)*100%
Intra tot HO SR = (intra eNB HO prep successes) / (intra eNB HO preparations) * (intra eNB HO successes) / (intra eNB HO attempts) *100% = (intra eNB HO attempts) / (intra eNB HO preparations) * (intra eNB HO successes) / (intra eNB HO attempts)*100% = (intra eNB HO successes) / * Inter X2 based HO prep SR =(number of successful inter eNB X2 based HO prep) /(total number of inter eNB X2 based HO preparations)*100%=(number of inter eNB X2 based HO attempts) /(total number of inter eNB X2 based HO preparations)*100%
Inter X2 based HO preparations = (total number of inter eNB X2 based HO preparations) Inter S1 based HO prep SR =(number of successful inter eNB S1 based HO prep) /(total number of inter eNB S1 based HO preparations)*100%=(number of inter eNB S1 based HO attempts) /(total number of inter eNB S1 based HO preparations)*100%
Inter S1 based HO preparations = total number of inter eNB S1 based HO re arations Inter X2 based HO prep FR = (number of inter eNB X2 based HO prep f ailure_x) / (total number of inter eNB X2 based HO preparations)*100%
Inter X2 based HO prep FR = (number of inter eNB X2 based HO prep f ailure_x) / (total number of inter eNB X2 based HO preparations)*100%
Inter X2 based HO prep FR = (number of inter eNB X2 based HO prep f ailure_x) / (total number of inter eNB X2 based HO preparations)*100%
Inter S1 based HO prep FDR =(number of inter eNB S1 based HO prep failure_x) / (total number of inter eNB S1 based HO preparations)*100%
Inter S1 based HO prep FDR =(number of inter eNB S1 based HO prep failure_x) / (total number of inter eNB S1 based HO preparations)*100%
Inter S1 based HO prep FDR =(number of inter eNB S1 based HO prep failure_x) / (total number of inter eNB S1 based HO preparations)*100%
Inter X2 based HO SR =(number of successful inter eNB X2 based HOs) /(number of inter eNB X2 based HO attempts)*100%
Inter X2 based HO Att = (number of inter eNB X2 based HO attempts) Inter S1 based HO SR =(number of successful inter eNB S1 based HOs) /(number of inter eNB S1 based HO attempts)*100%
Inter S1 based HO Att =(number of inter eNB S1 based HO attempts) Inter X2 based HO FR =(number of unsuccessful inter eNB X2 based HOs) /(number of inter eNB X2 based HO attempts)*100%
Inter S1 based HO FR =(number of unsuccessful inter eNB S1 based HOs) /(number of inter eNB S1 based HO attempts)*100%
Inter tot X2 based HO SR= (inter eNB X2 based HO prep successes) / (inter eNB X2 based HO preparations) * (inter eNB X2 based HO successes) / (inter eNB X2 based HO attempts) *100%= (inter eNB X2 based HO attempts) / (inter eNB X2 based HO preparations) * (inter eNB X2 based HO successes) / (inter eNB X2 based HO attempts)*100%= (inter eNB X2 based HO successes) /
Inter tot S1 based HO SR= (inter eNB S1 based HO prep successes) / (inter eNB S1 based HO preparations) * (inter eNB S1 based HO successes) / (inter eNB S1 based HO attempts) *100%= (inter eNB S1 based HO attempts) / (inter eNB S1 based HO preparations) * (inter eNB S1 based HO successes) / (inter eNB S1 based HO attempts)*100%= (inter eNB S1 based HO successes) / CSFB AttDR=( CS Fallback Attempts _x / CS Fallback Attempts all)*100% CSFB AttDR=( CS Fallback Attempts _x / CS Fallback Attempts all)*100% CSFB AttDR=( CS Fallback Attempts _x / CS Fallback Attempts all)*100% Inter Frequency HO SR = (number of successful Inter-Frequency HOs) / (number of Inter-Frequency HO attempts)*100%
Inter Frequency HO SR = (number of successful Inter-Frequency HOs measurement gap assisted) / (number of Inter-Frequency HO attempts measurement gap assisted)*100%
AVG DL PDCP CELL THP = average PDCP cell throughput DL AVG DL PDCP CELL THP QCI1= average PDCP cell throughput DL for QCI1 DRBs AVG UL PDCP CELL THP = average PDCP cell throughput UL AVG UL PDCP CELL THP QCI1= average PDCP cell throughput UL for QCI1 DRBs AVG DL RLC CELL THP =(DL transmitted RLC PDU volume)*8 / (MEASUREMENT_DURATION)*60 AVG UL RLC CELL THP= (UL received RLC PDU volume)*8 / MEASUREMENT DURATION *60 AVG IN X2 SIG THP = (incoming X2AP signaling volume)*8 / (MEASUREMENT_DURATION)*60 AVG OUT X2 SIG THP = (outgoing X2AP signaling volume)*8 / (MEASUREMENT_DURATION)*60 AVG X2 DAT THP IN=(incoming X2AP user plane d ata volume *8/1000 / MEASUREMENT DURATION *60 AVG X2 DAT THP OUT=(outgoing X2AP user plane data volume *8/1000 / MEASUREMENT DURATION *60
AVG DL PRBs = (average (used/available) DL PRBs per TTI)
AVG UL PRBs = (average (used/available)UL PRBs per TTI)
CELL AVR=(time of cell is available for services) / (total measured time)=(number of samples when cell is available) / number of all sam les CELL PL UAVR= (time of cell is planned unavailable for services)/ (total measured time)=(number of samples when cell is planned unavailable number of all sam les CELL UPL UAVR=(time of cell is unplanned unavailable for services) / (total measured time)= (number of samples when cell is unplanned unavailable) /(number of all samples) CELL AVR BLU =(number of samples when cell is available) / (number of all samples number of samples when cell is lanned unavailable ACT UE D AVG DL = ( DL average number of active UEs with data in buffer per cell) ACT UE D AVG DL QCI1 =( DL average number of active UEs with data in buffer for DRBs of QCI1 per cell) ACT UE D AVG DL non GBR=( DL average number of active UEs with data in buffer for non-GBR DRBs per cell) ACT UE D AVG UL = (UL average number of active UEs with data in buffer per cell) ACT UE D AVG UL QCI1 =(UL average number of active UEs with buffered data in UL for DRBs of QCI1) ACT UE D AVG UL non GBR =(UL average number of active UEs with buffered data in UL for non GBR DRBs) ACT UE D MAX DL = ( DL maximum number of active UEs with data in buffer per cell) ACT UE D MAX UL= (UL maximum number of active UEs with data in buffer per cell) ACT UE ENB = (average number of a ctive UEs per eNB) IP VOL IN=(incoming IP octets [kB]) / 1000 IP VOL UL=(outgoing IP octets [kB]) / 1000 IP THP DL = (incoming IP octets [kB])*8 / measurement duration [sec]
IP THP UL = (outgoing IP octets [kB])*8 / measurement duration [sec]
IP IN ER = (incoming erroneous IP packets) / (total incoming IP packets) FtpCmdSR= number_of(successful_ftp_commands\number_of(total_ftp_com mands *100 FtpSessionSR=number_of(completed_sessions)\number_of(sucess fully_started_sessions)*100 FtpServiceAccessTime[s]=t_content sent or received-t_ftp command started FtpSessionTime[s] = t_sessionend-t_sessionstart FtpMeanDataRateUL/DL = {transffered_data_volume_UL/DL[bytes]*8}\{transfer_time[s]} VoIPCallSetupTime *s+ = t Connection Established − t Push Dial Button
VoIPCallSR ={ number_of (successful_calls)}\{number_of (call_setup_requests)}*100
VoIPCallDR = {number_of (dropped_calls)}\ {number_of (successful_calls)}*100
VoIPCallDR = {number_of (dropped_calls)}\ {number_of (successful_calls)}*100
VoIPFER = {number_of (lost_corrupted_discarded_frames)}\ {number_of (all_frames_sent)}*100
Voice Interrupt Time *ms+ = tfirst packet TeNB – tlast packet SeNB
Attach Time *ms+ = tAttach Complete – tAttach Request
LTENwAttSR = (number_of_successful_attachments)\ (number_of_all_attempts) *100% Service Request Time *ms+ = tRRC_Reconfig – tRRC_Request
Service Request Time *s+ = tRRC_Reconfig – tRRC_Request
EPSSR =[number_of(RRC_CONN_RECONFIGURATION_COMPLETE)]\ [number_of(RRC_CONNECTION_REQUEST)]*100
EPSBearerD R = [number_of(dropped_calls)]\ [number_of(successful_calls)]*100
Handover Procedure Time *ms+ = tHO_Confirm – tHO_Command
HOSR = [number_of(Handover_Confirm)]\ [number_of(Handover_Request)]*100 Paging Time *s+ = tSRT network = initiated – tSRT UE initiated
PagingFR = [number_of(Paging_Failures)]\[number_of(Paging_Attempts)]*10 0
Round Trip Time *ms+ = tICMP = Echo Reply – tICMP Echo Request
UserDataRate = (transferred_data_volume[bytes]*8\(transfer_time[s])*1000
PLR = [number_of(lost_corrupted_packets)]\[number_of(all_packets_se nt)]*100 Service Interrupt Time *ms+ = tfirst = packet to/from TeNB – tlast packet to/from SeNB
RBPLR = [number_of(lost_corrupted_packets)]\ [number_of(all_packet_sent)]*100
RBUserDataRate = (transferred_data_volume *bytes+)8\(transfer_time *s+) 10–6
CellThroughput = (transferred_data_volume *bytes+)8\(transfer_time *s+) 10–6
Residual BLER = (number_of_lost_corrupted_radio_blocks)\(number_of_all_radio blocks sent *100 Rate={100}*[L.Paging.UU.Succ]/[L.Paging.UU.Att] rate=100*S1_mode_TAU_success_times/S1_mode_TAU_times 100* SAE_bearer_setup_success_times/ SAE bearer setu re uest times
Counter ID
KPI Formula with Counters Names
100*sum[M8006C1] /sum[M8006C0]
100*sum([EPS_BEARER_SETUP_COMPLETIONS]) / sum([EPS_BEARER_SETUP_ATTEMPTS])
100*sum([M8006C35]+ [M8006C36]) /sum([M8006C17]+ [M8006C18])
100*sum([EPS_BEARER_STP_COM_INI_QCI1+ EPS_BEAR_STP_COM_INI_NON_GBR])/ sum([EPS_BEARER_STP_ATT_INI_QCI_1+ EPS BEAR STP ATT INI NON GBR 100*sum([EPS_BEARER_SETUP_COMPLETIONS EPS_BEARER_STP_COM_INI_QCI1 EPS_BEAR_STP_COM_INI_NON_GBR]) / sum([EPS_BEARER_SETUP_ATTEMPTS EPS_BEARER_STP_ATT_INI_QCI_1-
100*sum([M8006C1] - [M8006C35] - [M8006C36]) /sum([M8006C0] - [M8006C17] - [M8006C18])
sum([M8006C0])
sum([EPS_BEARER_SETUP_ATTEMPTS])
100* sum([M8006C2]) / sum([M8006C0])
100*sum([EPS_BEARER_SETUP_FAIL_RNL]) /sum ([EPS_BEARER_SETUP_ATTEMPTS]) 100* sum([EPS_BEARER_SETUP_FAIL_TRPORT]) / sum [EPS BEARER SETUP ATTEMPTS] 100* sum([EPS_BEARER_SETUP_FAIL_RESOUR]) / sum([EPS_BEARER_SETUP_ATTEMPTS]) 100* sum([EPS_BEARER_SETUP_FAIL_OTH]) / sum([EPS_BEARER_SETUP_ATTEMPTS]) 100*sum([INI_CONT_STP_COMP]) / sum([INI_CONT_STP_REQ])
100* sum([M8006C3]) / sum([M8006C0]) 100* sum([M8006C4]) / sum([M8006C0]) 100* sum([M8006C5]) / sum([M8006C0]) 100*sum([M8000C1]) / sum([M8000C0])
sum([M8000C0])
sum([INI_CONT_STP_REQ])
100*sum([M8000C2]) / sum([M8000C0])
100*sum([INI_CONT_STP_FAIL_RNL]) / sum([INI_CONT_STP_REQ])
100*sum([M8000C3]) / sum([M8000C0])
100*sum([INI_CONT_STP_FAIL_TRPORT]) / sum([INI_CONT_STP_REQ])
100*sum([M8000C4]) / sum([M8000C0])
100*sum([INI_CONT_STP_FAIL_RESOUR]) / sum([INI_CONT_STP_REQ])
100*sum([M8000C5]) / sum([M8000C0])
100*sum([INI_CONT_STP_FAIL_OTHER]) / sum([INI_CONT_STP_REQ])
100*sum([M8000C7]) / sum([M8000C6])
100*sum([S1_SETUP_SUCC]) / sum([S1_SETUP_ATT])
sum([M8000C6])
sum([S1_SETUP_ATT])
100*sum([M8000C8]) / sum([M8000C6])
100*sum([S1_SETUP_FAIL_NO_RESP]) / sum [S1 SETUP ATT]
100*sum([M8000C9]) / sum([M8000C6]) 100*sum([M8000C25]) / sum([M8000C23])
100*sum([S1_SETUP_FAIL_IND_BY_MME]) / sum [S1 SETUP ATT] 100*sum([([UE_CONTEXT_MOD_FAIL]) / sum([UE_CONTEXT_MOD_ATT])
DATA_RB_STP_ATT = sum([M8007C0])
DATA_RB_STP_ATT = sum([DATA_RB_STP_ATT])
100*sum([M8007C1]) / sum([M8007C0])
100*sum([DATA_RB_STP_COMP]) / sum([DATA_RB_STP_ATT])
100*sum([M8007C5])+([M8007C6]) / 100*sum([RB_REL_REQ_RNL]+ sum([M8007C3]+([M8007C4]+[M8007C5]+[M8007C13]+[M [RB_REL_REQ_OTHER]) / 8007C6]) sum([RB_REL_REQ_NORM_REL]+ [RB_REL_REQ_DETACH_PROC]+ [RB_REL_REQ_RNL]+ [RB_REL_REQ_RNL_REDIR]+ RB SR= 100 - (100*sum([M8007C5])+([M8007C6]) / RB SR= 100 - LTE_5004 sum([M8007C3]+([M8007C4]+[M8007C5]+[M8007C13]+[M 8007C6] sum([M8013C17]) sum ([SIGN_CONN_ESTAB_ATT_MO_S])
sum([M8013C18])
sum([SIGN_CONN_ESTAB_ATT_MT])
sum([M8013C19])
sum([SIGN_CONN_ESTAB_ATT_MO_D])
sum([M8013C20])
sum([SIGN_CONN_ESTAB_ATT_OTHERS])
sum([M8013C21])
sum([SIGN_CONN_ESTAB_ATT_EMG])
100*sum([M8013C5]) / 100*sum([SIGN_CONN_ESTAB_COMP]) / sum([M8013C17]+[M8013C18]+[M8013C19]+[M8013C20]) sum([SIGN_CONN_ESTAB_ATT_MO_S]+ [SIGN_CONN_ESTAB_ATT_MT]+ [SIGN_CONN_ESTAB_ATT_MO_D]+ 100*sum([M8013C26]) / sum([M8013C21])
100*sum([SIGN_CONN_ESTAB_COMP_EMG]) / sum([SIGN_CONN_ESTAB_ATT_EMG])
100*sum([M8013C6]) / 100*sum([SIGN_EST_F_RRCCOMPL_MISSING]) / sum([M8013C17]+[M8013C18]+[M8013C19]+[M8013C20]) sum([SIGN_CONN_ESTAB_ATT_MO_S]+ [SIGN_CONN_ESTAB_ATT_MT]+ [SIGN_CONN_ESTAB_ATT_MO_D]+ 100*sum([M8013C7]) / 100*sum([SIGN_EST_F_RRCCOMPL_ERROR]) / sum([M8013C17]+[M8013C18]+[M8013C19]+[M8013C20]) sum([SIGN_CONN_ESTAB_ATT_MO_S]+ [SIGN_CONN_ESTAB_ATT_MT]+ [SIGN_CONN_ESTAB_ATT_MO_D]+ 100*sum([M8013C8]) / 100*sum([SIGN_CONN_ESTAB_FAIL_RRMRAC]) / sum([M8013C17]+[M8013C18]+[M8013C19]+[M8013C20]) sum([SIGN_CONN_ESTAB_ATT_MO_S]+ [SIGN_CONN_ESTAB_ATT_MT]+ [SIGN_CONN_ESTAB_ATT_MO_D]+ 100*sum([SIGN_CONN_ESTAB_FAIL_EMG]) / sum([SIGN_CONN_ESTAB_ATT_MO_S]+ [SIGN_CONN_ESTAB_ATT_MT]+ [SIGN_CONN_ESTAB_ATT_MO_D]+ 100*sum([M8008C2]) / sum([M8008C1]) sum([M8008C1])
100*sum([DISC_RRC_PAGING]) / sum [RRC PAGING REQUESTS] sum ([RRC_PAGING_REQUESTS])
100*sum([M8006C12]+[M8006C14]+[M8006C13])/ sum([M8006C6]+[M8006C7]+[M8006C8]+ [M8006C9] + [M8006C15]+ [M8006C10] + [M8006C12] +[M8006C14] +[M8006C13])
100*sum([ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+ [ENB_EPS_BEARER_REL_REQ_OTH]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100 * sum([M8006C12])/ sum([M8006C6] + [M8006C7] + [M8006C8] + [M8006C9] + [M8006C15] + [M8006C10] + [M8006C12] + [M8006C14] + [M8006C13])
100*sum([ENB_EPS_BEARER_REL_REQ_RNL]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100 * sum([M8006C14])/ sum([M8006C6] + [M8006C7] + [M8006C8] + [M8006C9] + [M8006C15] + [M8006C10] + [M8006C12] + [M8006C14] + [M8006C13])
100*sum([ENB_EPS_BEARER_REL_REQ_TNL]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100*sum([M8006C13])/ sum([M8006C6] + [M8006C7] + [M8006C8] + [M8006C9] + [M8006C15] + [M8006C10] + [M8006C12] + [M8006C14] + [M8006C13])
100*sum([ENB_EPS_BEARER_REL_REQ_OTH]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100*sum([M8006C8])/ sum([M8006C6] + [M8006C7] + [M8006C8] + [M8006C9] + [M8006C15] + [M8006C10] + [M8006C12] + [M8006C14] + [M8006C13])
100*sum([EPC_EPS_BEARER_REL_REQ_RNL]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH] + [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100*sum([M8006C9])/ sum([M8006C6] + [M8006C7] + [M8006C8] + [M8006C9] + [M8006C15] + [M8006C10] + [M8006C12] + [M8006C14] + [M8006C13])
100*sum([EPC_EPS_BEARER_REL_REQ_OTH]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH] + [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM]+ [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100*sum([M8006C6]+[M8006C7]+[M8006C15]+ [M8006C10]) / sum([M8006C6]+[M8006C7]+[M8006C8]+ [M8006C9] + [M8006C15]+ [M8006C10] + [M8006C12] +[M8006C14] +[M8006C13])
100*sum([EPC_EPS_BEARER_REL_REQ_NORM]+ EPC_EPS_BEARER_REL_REQ_DETACH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+
100*sum([M8006C10]+[M8006C15]+[M8006C6]+[M8006C7 100*sum([ENB_EPS_BEARER_REL_REQ_NORM]+ ]+[M8006C8]+[M8006C9]) / ENB_EPS_BEARER_REL_REQ_RNL_REDIR]+ sum([M8006C6]+[M8006C7]+[M8006C8]+ [M8006C9] + [EPC_EPS_BEARER_REL_REQ_NORM]+ [M8006C15]+ [M8006C10] + [M8006C12] +[M8006C14] [EPC_EPS_BEARER_REL_REQ_DETACH]+ +[M8006C13]) [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH]+ [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+ 100* sum([M8006C2]) / sum([M8006C0]) 100* sum([M8006C3]) / sum([M8006C0]) 100* sum([M8006C4]) / sum([M8006C0]) 100* sum([M8006C5]) / sum([M8006C0]) 100*sum([M8006C8]+[M8006C9] + [M8006C12]+[M8006C14]+ [M8006C13]) / sum([M8006C6]+[M8006C7]+[M8006C8]+ [M8006C9] + [M8006C15]+ [M8006C10] + [M8006C12] +[M8006C14] +[M8006C13])
100*sum([M8000C2]) / sum([M8000C0]) 100*sum([M8000C3]) / sum([M8000C0]) 100*sum([M8000C4]) / sum([M8000C0]) 100*sum([M8000C5]) / sum([M8000C0]) 100*sum([M8000C8]) / sum([M8000C6]) 100*sum([M8000C9]) / sum([M8000C6]) sum([M51120C0]) / sum([M51120C4])*100% avg([M8001C2])
sum([EPS_BEARER_SETUP_FAIL_RNL]) / sum [EPS BEARER SETUP ATTEMPTS] 100* sum([EPS_BEARER_SETUP_FAIL_TRPORT]) / sum [EPS BEARER SETUP ATTEMPTS] 100* sum([EPS_BEARER_SETUP_FAIL_RESOUR]) / sum([EPS_BEARER_SETUP_ATTEMPTS]) 100* sum([EPS_BEARER_SETUP_FAIL_OTH]) / sum([EPS_BEARER_SETUP_ATTEMPTS]) 100*sum([EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+ [ENB_EPS_BEARER_REL_REQ_OTH]) / sum([EPC_EPS_BEARER_REL_REQ_NORM]+ [EPC_EPS_BEARER_REL_REQ_DETACH]+ [EPC_EPS_BEARER_REL_REQ_RNL]+ [EPC_EPS_BEARER_REL_REQ_OTH] + [ENB_EPSBEAR_REL_REQ_RNL_REDIR]+ [ENB_EPS_BEARER_REL_REQ_NORM] + [ENB_EPS_BEARER_REL_REQ_RNL]+ [ENB_EPS_BEARER_REL_REQ_TNL]+ 100*sum([INI_CONT_STP_FAIL_RNL]) / sum([INI_CONT_STP_REQ]) 100*sum([INI_CONT_STP_FAIL_TRPORT]) / sum [INI CONT STP REQ] 100*sum([INI_CONT_STP_FAIL_RESOUR]) / sum [INI CONT STP REQ] 100*sum([INI_CONT_STP_FAIL_OTHER]) / sum([INI_CONT_STP_REQ]) 100*sum([S1_SETUP_FAIL_NO_RESP]) / sum([S1_SETUP_ATT]) 100*sum([S1_SETUP_FAIL_IND_BY_MME]) / sum [S1 SETUP ATT] sum([ifInErrors15]) / sum [ifInPackets15] *100% avg([PDCP_SDU_DELAY_DL_DTCH_MEAN])
avg([M8001C269])
avg([PDCP_RET_DL_DEL_MEAN_QCI_1])
avg([M8001C270])
avg([PDCP_RET_DL_DEL_MEAN_NON_GBR])
avg([M8001C5])
avg([PDCP_SDU_DELAY_UL_DTCH_MEAN])
sum([M8001C138]) / sum([M8001C137]+[M8001C138])*100%
sum([RLC_PDU_RE_TRANS]) / sum([RLC_PDU_FIRST_TRANS]+ RLC PDU RE TRANS *100% sum([UL_RLC_PDU_DUPL_REC]) / sum([UL_RLC_PDU_REC_TOT])*100%
sum([M8001C143]) / sum[M8001C142])*100%
avg([M8005C2])
avg([RSSI_PUCCH_AVG])
avg([M8005C5])
avg([RSSI_PUSCH_AVG])
avg([M8005C92])
avg([SINR_PUCCH_AVG])
avg([M8005C95])
avg([SINR_PUSCH_AVG])
sum(1*[M8010C37]+ 2*[M8010C38] + 3*[M8010C39] + 4*[M8010C40] + 5*[M8010C41] + 6*[M8010C42] + 7*[M8010C43] + 8*[M8010C44] + 9*[M8010C45] + 10*[M8010C46]+ 11*[M8010C47] + 12*[M8010C48] + 13*[M8010C49]+ 14*[M8010C50] + 15*[M8010C51]) / sum([M8010C36] + [M8010C37] + [M8010C38] + [M8010C39] + [M8010C40] + [M8010C41] + [M8010C42] + [M8010C43] + [M8010C44] + [M8010C45] + [M8010C46] + [M8010C47] + [M8010C48] + [M8010C49] + [M8010C50] + [M8010C51])
sum(1*[UE_REP_CQI_LEVEL_01]+ 2*[UE_REP_CQI_LEVEL_02]+ 3*[UE_REP_CQI_LEVEL_03]+ 4*[UE_REP_CQI_LEVEL_04]+ 5*[UE_REP_CQI_LEVEL_05]+ 6*[UE_REP_CQI_LEVEL_06]+ 7*[UE_REP_CQI_LEVEL_07]+ 8*[UE_REP_CQI_LEVEL_08]+ 9*[UE_REP_CQI_LEVEL_09]+ 10*[UE_REP_CQI_LEVEL_10]+ 11*[UE_REP_CQI_LEVEL_11]+ 12*[UE_REP_CQI_LEVEL_12]+ 13*[UE_REP_CQI_LEVEL_13]+ 14*[UE_REP_CQI_LEVEL_14]+ 15*[UE_REP_CQI_LEVEL_15]) / sum([UE_REP_CQI_LEVEL_00]+[UE_REP_CQI_LEVEL_01]+ [UE_REP_CQI_LEVEL_02]+[UE_REP_CQI_LEVEL_03]+ [UE_REP_CQI_LEVEL_04]+[UE_REP_CQI_LEVEL_05]+ [UE_REP_CQI_LEVEL_06]+[UE_REP_CQI_LEVEL_07]+ [UE_REP_CQI_LEVEL_08]+[UE_REP_CQI_LEVEL_09]+ [UE_REP_CQI_LEVEL_10]+[UE_REP_CQI_LEVEL_11]+ + + avg([CQI_OFF_MEAN])/1000
avg([M8010C54])/1000
100*sum([M8009C6]) / sum([M8009C2])
100*sum([ATT_INTRA_ENB_HO]) / sum([INTRA_ENB_HO_PREP])
sum([M8009C2])
sum([INTRA_ENB_HO_PREP])
100*sum([M8009C3]) / sum([M8009C2])
100*sum([FAIL_ENB_HO_PREP_AC]) / sum([INTRA_ENB_HO_PREP])
100*sum([M8009C5]) / sum([M8009C2])
100*sum([FAIL_ENB_HO_PREP_OTH]) / sum([INTRA_ENB_HO_PREP])
100*sum([M8009C7]) / sum([M8009C6])
100*sum([SUCC_INTRA_ENB_HO]) / sum([ATT_INTRA_ENB_HO])
sum([M8009C6])
sum([ATT_INTRA_ENB_HO])
100*sum([M8009C8]) / sum([M8009C6])
100*sum([ENB_INTRA_HO_FAIL]) / sum([ATT_INTRA_ENB_HO])
100*sum([M8009C7]) / sum([M8009C2])
100*sum([SUCC_INTRA_ENB_HO]) / sum([INTRA_ENB_HO_PREP])
100*sum([M8014C6]) / sum([M8014C0])
100*sum([ATT_INTER_ENB_HO]) / sum ([INTER_ENB_HO_PREP])
sum([M8014C0])
sum ([INTER_ENB_HO_PREP])
100*sum([M8014C18]) / sum([M8014C14])
100*sum([INTER_ENB_S1_HO_ATT]) / sum ([INTER_ENB_S1_HO_PREP])
sum([M8014C14])
sum ([INTER_ENB_S1_HO_PREP])
100*sum([M8014C2]) / sum([M8014C0])
100*sum([FAIL_ENB_HO_PREP_TIME]) / sum([INTER_ENB_HO_PREP])
100*sum([M8014C3]) / sum([M8014C0])
100*sum([FAIL_ENB_HO_PREP_AC]) / sum ([INTER_ENB_HO_PREP])
100*([M8014C5]) / sum([M8014C0])
100*sum([FAIL_ENB_HO_PREP_OTHER]) / sum ([INTER_ENB_HO_PREP])
100*sum([M8014C15]) / sum([M8014C14])
100*sum([INTER_S1_HO_PREP_FAIL_TIME]) / sum ([INTER_ENB_S1_HO_PREP])
100*sum([M8014C16]) / sum([M8014C14])
100*sum([INTER_S1_HO_PREP_FAIL_NORR]) / sum([INTER_ENB_S1_HO_PREP])
100*sum([M8014C17]) / sum([M8014C14])
100*sum([INTER_S1_HO_PREP_FAIL_OTHER]) / sum ([INTER_ENB_S1_HO_PREP])
100*sum([M8014C7]) / sum([M8014C6])
100*sum([SUCC_INTER_ENB_HO]) / sum ([ATT_INTER_ENB_HO])
sum([M8014C6])
sum ([ATT_INTER_ENB_HO])
100*sum([M8014C19]) / sum([M8014C18])
100*sum([INTER_ENB_S1_HO_SUCC]) / sum ([INTER_ENB_S1_HO_ATT])
sum([M8014C18])
sum ([INTER_ENB_S1_HO_ATT])
100*sum([M8014C8]) / sum([M8014C6])
100*sum([INTER_ENB_HO_FAIL]) / sum ([ATT_INTER_ENB_HO])
100*sum([M8014C20]) / sum([M8014C18])
100*sum([INTER_ENB_S1_HO_FAIL]) / sum ([INTER_ENB_S1_HO_ATT])
100*sum([M8014C7]) / sum([M8014C0])
100*sum([SUCC_INTER_ENB_HO]) / sum([INTER_ENB_HO_PREP])
100*sum([M8014C19]) / sum([M8014C14])
100*sum([INTER_ENB_S1_HO_SUCC]) / sum([INTER_ENB_S1_HO_PREP])
100*sum([M8016C12]) / sum([M8016C11])
100*sum([CSFB_REDIR_CR_CMODE_ATT]) / sum([CSFB_REDIR_CR_ATT])
100*sum([M8016C11] - [M8016C12]) / sum([M8016C11])
100*sum([CSFB_REDIR_CR_ATT] [CSFB_REDIR_CR_CMODE_ATT]) / sum CSFB REDIR CR ATT 100*sum([CSFB_REDIR_CR_EMERGENCY_ATT]) / sum([CSFB_REDIR_CR_ATT])
100*sum([M8016C13]) / sum([M8016C11])
100*sum([M8021C2]) / sum([M8021C0])
100*sum(HO_INTFREQ_SUCC]) / sum (HO_INTFREQ_ATT])
100*sum([M8021C3]) / sum([M8021C1])
100*sum(HO_INTFREQ_GAP_SUCC]) / sum (HO_INTFREQ_GAP_ATT])
avg([M8012C26])
avg([PDCP_DATA_RATE_MEAN_DL])
avg([M8012C143])
avg([PDCP_DATA_RATE_MEAN_DL_QCI_1])
avg([M8012C23])
avg([PDCP_DATA_RATE_MEAN_UL])
avg([M8012C116])
avg([PDCP_DATA_RATE_MEAN_UL_QCI_1])
sum([M8012C18])*8 / (sum(MEASUREMENT_DURATION)*60) sum([M8012C17])*8 / sum MEASUREMENT DURATION *60 sum([M8004C0])*8 /(sum(MEASUREMENT_DURATION)*60)
sum([RLC_PDU_VOL_TRANSMITTED])*8 / (sum(MEASUREMENT_DURATION)*60) sum([RLC_PDU_VOL_RECEIVED])*8 / sum MEASUREMENT DURATION *60 sum([VOLUME_X2_IN_SIG_DATA])*8 / (sum(MEASUREMENT_DURATION)*60) sum([M8004C1])*8 /(sum(MEASUREMENT_DURATION)*60) sum([VOLUME_X2_OUT_SIG_DATA])*8 / (sum(MEASUREMENT_DURATION)*60) sum([M8004C2])*8/1000 / sum MEASUREMENT DURATION *60 sum([M8004C3])*8/1000 / sum MEASUREMENT DURATION *60
sum([X2_DATA_VOL_IN_UPLANE])*8/1000 / sum MEASUREMENT DURATION *60 sum([X2_DATA_VOL_OUT_UPLANE])*8/1000 / sum MEASUREMENT DURATION *60
avg([M8011C37])/10
avg([DL_PRB_UTIL_TTI_MEAN])/10
avg([M8011C24])/10
avg([UL_PRB_UTIL_TTI_MEAN])/10
sum([M8020C3]) / sum([M8020C6])*100%
sum([SAMPLES_CELL_AVAIL]) / sum([DENOM_CELL_AVAIL])*100%
sum([M8020C4]) / sum([M8020C6])*100%
sum([SAMPLES_CELL_PLAN_UNAVAIL]) / sum([DENOM_CELL_AVAIL])*100%
sum([M8020C5]) / sum([M8020C6])*100%
sum([SAMPLES_CELL_UNPLAN_UNAVAIL]) / sum([DENOM_CELL_AVAIL])*100%
100*sum([M8020C3]/sum([M8020C6] - [M8020C4])
100*sum(SAMPLES_CELL_AVAIL/sum (DENOM_CELL_AVAIL-SAMPLES_CELL_PLAN_UNAVAIL)
avg([M8001C147])
avg([DL_UE_DATA_BUFF_AVG])
avg([M8001C227])
avg([UE_DRB_DL_DATA_QCI_1])
avg([M8001C235])
avg([UE_DRB_DL_DATA_NON_GBR])
avg([M8001C150])
avg([UL_UE_DATA_BUFF_AVG])
avg([M8001C419])
avg([UE_DRB_UL_DATA_QCI_1])
avg([M8001C420])
avg([UE_DRB_UL_DATA_NON_GBR])
max([M8001C148])
max([DL_UE_DATA_BUFF_MAX])
max([M8001C151])
max([UL_UE_DATA_BUFF_MAX])
avg([M8018C0])
avg([ENB_LOAD_ACT_UE_AVG])
LTE_5073a =sum([M51120C1]) / 1000 LTE_5662a =sum([M51127C1]) / 1000 LTE_5072b =sum([M51120C3]) / 1000 LTE_5663b =sum([M51127C3]) / 1000 LTE_5075a = sum([M51120C1]) *8 / (sum(MEASUREMENT_DURATION)*60) LTE_5665a = sum([(M51127C1]) *8 / sum MEASUREMENT DURATION *60
sum([ifInOctets15]) / 1000 sum([ifOutOctets15]) / 1000 LTE_5075a = sum([ifInOctets15]) *8 / (sum(MEASUREMENT_DURATION)*60) LTE_5665a = sum([ifInOctets15]) *8 / sum MEASUREMENT DURATION *60
LTE_5074b = sum([M51120C3]) *8 /(sum(MEASUREMENT_DURATION)*60) LTE_5664b = sum([M51127C3]) *8 sum MEASUREMENT DURATION *60 sum([M51120C0]) / sum([M51120C4])*100%
LTE_5074b = sum([ifOutOctets15]) *8 / (sum(MEASUREMENT_DURATION)*60) LTE_5664b = sum([ifOutOctets15]) *8 / sum MEASUREMENT DURATION *60 sum([ifInErrors15]) / sum([ifInPackets15])*100% FtpCmdSR= number_of(successful_ftp_commands\number_of(total_ftp_ commands *100 FtpSessionSR=number_of(completed_sessions)\number_of(s ucessfully_started_sessions)*100 FtpServiceAccessTime[s]=t_content sent or received-t_ftp command started FtpSessionTime[s] = t_sessionend-t_sessionstart FtpMeanDataRateUL/DL = {transffered_data_volume_UL/DL[bytes]*8}\{transfer_time[s VoIPCallSetupTime *s+ = t Connection Established − t Push Dial Button
VoIPCallSR ={ number_of (successful_calls)}\{number_of (call_setup_requests)}*100
VoIPCallDR = {number_of (dropped_calls)}\ {number_of (successful_calls)}*100
VoIPCallDR = {number_of (dropped_calls)}\ {number_of (successful_calls)}*100
VoIPFER = {number_of (lost_corrupted_discarded_frames)}\ {number_of (all_frames_sent)}*100
Voice Interrupt Time *ms+ = tfirst packet TeNB – tlast packet SeNB
Attach Time *ms+ = tAttach Complete – tAttach Request
LTENwAttSR = (number_of_successful_attachments)\ (number_of_all_attempts) *100% Service Request Time *ms+ = tRRC_Reconfig – tRRC_Request
Service Request Time *s+ = tRRC_Reconfig – tRRC_Request
EPSSR =[number_of(RRC_CONN_RECONFIGURATION_COMPLETE)]\ [number_of(RRC_CONNECTION_REQUEST)]*100
EPSBearerD R = [number_of(dropped_calls)]\ [number_of(successful_calls)]*100
Handover Procedure Time *ms+ = tHO_Confirm – tHO_Command
HOSR = [number_of(Handover_Confirm)]\ [number_of(Handover_Request)]*100 Paging Time *s+ = tSRT network = initiated – tSRT UE initiated
PagingFR = [number_of(Paging_Failures)]\[number_of(Paging_Attempts) ]*100
Round Trip Time *ms+ = tICMP = Echo Reply – tICMP Echo Request
UserDataRate = (transferred_data_volume[bytes]*8\(transfer_time[s])*1000
PLR = [number_of(lost_corrupted_packets)]\[number_of(all_packe ts_sent)]*100 Service Interrupt Time *ms+ = tfirst = packet to/from TeNB – tlast packet to/from SeNB
RBPLR = [number_of(lost_corrupted_packets)]\ [number_of(all_packet_sent)]*100
RBUserDataRate = (transferred_data_volume *bytes+)8\(transfer_time *s+) 10–6
CellThroughput = (transferred_data_volume *bytes+)8\(transfer_time *s+) 10–6
Residual BLER = (number_of_lost_corrupted_radio_blocks)\(number_of_all_r adio blocks sent *100 Rate={100}*[L.Paging.UU.Succ]/[L.Paging.UU.Att] rate=100*S1_mode_TAU_success_times/S1_mode_TAU_tim es 100* SAE_bearer_setup_success_times/ SAE bearer setu re uest times
Remarks
• intra LTE intra- and inter-frequency mobility • inter RAT mobility (LTE ↔ 2G/3G) • intra vs. inter eNB, the latter via X2, or S1 interface • intra vs. inter MME/S-GW