Accord 1998 Auto Tranny Diagram

Acura 2.3CL 1998-99 B6VA Accord 1998-02 BAXA/MAXA 2.3L Odyssey 1998 MDWA 2.3L Prelude 1997-01 M6HA 2.2L

94626

Transmission Housing Main Shaft 3rd & 4th

Reverse Idler Gear Shaft & Holder Counter Shaft Bearing

Secondary Shaft 1st & 2nd

Reverse Idler Gear Main Shaft Bearing Secondary Shaft Bearing

Speed Sensor, Counter Shaft

-2-

Counter Shaft

Right Side Cover

✣ Secondary Shaft

Note: Main shaft has left-hand threads

Counter Shaft

✰

Main Shaft

✰

✣ Not used in Prelude ✰ New shaft lock nuts, torque to 123 ft. lbs. / 167 N•m -3-

✰

-4-

-5-

✣

✣ ✣

✣ Not used in Prelude

TORQUE: 12 N•m (8.7 lbf•ft)

TORQUE: 44 N•m (33 lbf•ft)

-6-

STANDARD: 12 - 25 Ω

STANDARD: 12 - 25 Ω

-7-

Acura 2.3CL 1998-99 B6VA Accord 1998-02 BAXA/MAXA 2.3L Odyssey 1998 MDWA 2.3L STANDARD: Approx. 5 Ω

Prelude 1997-01 M6HA 2.2L

STANDARD: Approx. 4.0-9.0 Ω

-8-

PRESSURE Line

SHIFT LEVER POSITION N or P

FLUID PRESSURE SYMPTOM

PROBABLE CAUSE

No (or low) line pressure

Torque converter, ATF pump, pressure regulator valve, torque converter check valve

1st Clutch

1

No or low 1st pressure

1st clutch

2nd Clutch

2

No or low 2nd pressure

2nd clutch

3rd Clutch

D4

No or low 3rd pressure

3rd clutch

No or low 4th pressure

4th clutch

4th Clutch

R

Standard

Service Limit

850-910 kPa 120-130 psi

800 kPa/120 psi

900-960 kPa 130-140 psi*

860 kPa/130 psi*

840-920 kPa 120-130 psi

790 kPa/120 psi

890-970 kPa 130-140 psi*

860 kPa/130 psi*

Servo valve or 4th clutch

*Odyssey only.

-9-

Acura 2.3CL 1998-99 B6VA Accord 1998-02 BAXA/MAXA 2.3L Odyssey 1998 MDWA 2.3L Prelude 1997-01 M6HA 2.2L Shift Control Solenoid

Power Flow

BAXA, B6VA, MDWA Clutch End Plate-to-Top Disc Clearance: Service Limit: 1st Clutch: 2nd Clutch: 3rd Clutch: 4th Clutch:

1.15–1.35 mm (0.045–0.053 in.) 0.7–0.9 mm (0.028–0.035 in.) 0.6–0.8 mm (0.024–0.031 in.) 0.4–0.6 mm (0.016–0.024 in.)

M6HA Clutch End Plate-to-Top Disc Clearance: Service Limit: 1st Clutch: 2nd Clutch: 3rd Clutch: 4th Clutch:

1.15–1.35 mm (0.045–0.053 in.) 1.0–1.2 mm (0.039–0.047 in.) 0.6–0.8 mm (0.024–0.031 in.) 0.4–0.6 mm (0.016–0.024 in.)

If the clearance is not within the service limits, select a new clutch end plate from the appropriate table.

-10-

Odyssey 1998 MDWA 2.3L Prelude 1997-01 M6HA 2.2L O-RING

Acura 2.3CL 1998-99 B6VA Accord 1998-02 BAXA/MAXA 2.3L

BONDED

-11-

Acura 2.3CL 1998-99 B6VA Accord 1998-02 BAXA/MAXA 2.3L Odyssey 1998 MDWA 2.3L Prelude 1997-01 M6HA 2.2L 3rd & 4th Clutch

SOME OF THE INFORMATION IN THIS BOOKLET MAY HAVE BEEN PROVIDED OR APPROVED BY THE AUTOMATIC TRANSMISSION SERVICE GROUP AND/OR THE AUTOMATIC TRANSMISSION REBUILDERS ASSOCIATION. THE INFORMATION CONTAINED HEREIN IS ACCURATE TO THE BEST OF OUR KNOWLEDGE. WE ARE NOT RESPONSIBLE FOR ANY INACCURACIES OR WARRANTY CLAIMS WHICH MAY RESULT FROM THE USE OF THIS INFORMATION.