this is some other info. that will helpDescrição completa
Basic Electronics Tutorials
OPENFOAM tutorials basic
Simple Programming with Just Basic Basic Instructions Just BASIC is a programming language for the Windows operating system. It is completely free and it is suitable for creating all kind…Description complète
BASIC MAINTENANCE
teknik mesinDeskripsi lengkap
BASIC MAINTENANCEDeskripsi lengkap
teknik mesinFull description
Full description
Construction equipment in actual fieldFull description
construction equipmentsFull description
construction equipmentsFull description
Full description
Full description
rtyh
ppm
Aipu solids control is professional drilling mud management equipments manufacturer.This pdf is its products catalog .
Deskripsi lengkap
Full description
ansys
AVIAT EQUIPMENTS MAINTENANCE Basic Tutorials
TYPE OF INDOOR UNITS •
Eclipse edge
•
Eclipse GE3
•
CTR 8300
Tools to Log on •
Portal
•
Putty
•
Ethernet cable
•
computer
How to logon Edge and GE3 IDUs •
•
•
Connect your computer to NMS port
CTR 8300 •
•
Put the IP of the equipment Change the IP of your computer to the IP which is in the same network with the IP of the equipment, default gateway will be the IP of the equipment
•
Connect your computer to port 2 Open your browser and put the IP for the equipment. Change the IP of your computer to the IP which is in the same network with the IP of the equipment, default gateway will be the IP of the equipment
This is the portal That is where to put the IP address of equipment
This is Edge IDU opened with portal and the Cards shown as circuit These are the cards shown: RAC card(Radio Access Card)
That is where we put radio configurations
DAC 2 card(Data access card 2)
That is the card which is for E1 traffic Or tributaries(it carry up to 16 tributaries)
DAC3 card(Data access card 3)
That is the card for normal data like Ethernet traffic.
NCC card(Node control card)
How to check the ODU configuration Right Click on RAC Select plug-ins The portal will be displaying like this image •
•
•
How to check RSL level Right click on RAC Select performance
• •
How to change the IP of Equipment Click on configuration tab Select networking Then select IP addressing tab Change the IP to the planned IP addresses and subnet mask Click on send to save •
•
•
•
•
How to activate electrical port Right click on DAC 3 Click Plug ins Select Basics tab To activate it you have to make it Normal •
• • •
How to configure VLAN tagging Right click on DAC 3 Click Plug ins Select VLAN tab Choose the port according the planner Put configuration accordingly. • • • •
•
How to check Mac address table Right click on DAC GE3 card Select System/control •
•
Select Mac address table tab Tick MAC Flush Click on Load Flush •
• •
How to check traffic on Port Right click on DAC GE3 Select Performance First option is to select statistics tab Then click start • • •
•
Cont’
Right click on DAC GE3 Select Performance First option is to select Graphs tab Then click start Then you will see how the graphs moving • • •
• •
HOW TO LOG ON CTR 8300
Connect your computer to Ethernet port 2 Open your browser and put the IP for the equipment. User : root Password:admin123 •
•
• •
HOW TO CHECK RADIO LINK CONFIGURATION
Click on radio link Then click on radio configuration •
•
How to check performance Click on Statistics Then click on radio link performance •
•
HOW TO LOG ON USING PUTTY Open Putty Put the IP address of Equipment Select Telnet Then click open •
•
•
•
cont’ User : root Password:admin123
•
•
SOME CONFIGURATION COMMAND FOR TROUBLESHOOTING Show Vlan Then it shows you vlan database •
•
To show Mac address table
This command helps you to know how many users which are on the network. Then you can know if the client is using service or not •
•
NMS CONFIGURATIONS FOR TOWER END NMS Configuration on CTR 8311/12 NMS VLAN 9 VLAN 9 Gateway- 192.168.9.254/24 CTR NMS IP address- 192.168.9.120/24 - Assigned to Gi 0/2 STEP 1: Log in using default IP details •
•
• •
•
• •
•
•
•
•
• •
• •
•
• •
• •
• •
•
•
•
config t vlan 9 name NMS_Vlan ports add gi 0/2 untagged gi 0/2 ports add radio 0/1 ports add gi 0/1 exit interface vlan 9 ip address 192.168.9.120 255.255.255.0 no shut exit ! interface gi 0/2 no shut Map switch default management-out-band switchport Pvid9 exit ip route 0.0.0.0 0.0.0.0 192.168.9.254 snmp-server view all 1 included snmp-server community public version both read all notify all snmp-server community private version both read all write all notify all exit vlan 9 management
Cont’ Step 2: connect to Gi 0/2 Log in using the new IP details • • • •
• • •
• • • •
• • •
• •
• • • •
• • • • • • •
config t vlan 1 no ports exit interface gi 0/1 no management shut exit vlan 2 no ports exit interface vlan 2 no ip address 192.168.1.1 exit no vlan 2 exit interface range gi 0/1-2 switchport priority default 3 no shut exit interface radio 0/1 switchport priority default 3 no shut exit config save end copy running-config startup-config
NMS configuration for client end STEP 1: Log in using default IP details config t vlan 9 name NMS_Vlan ports add gi 0/2 untagged gi 0/2 ports add radio 0/1 exit • • • • • •
•
interface vlan 9 ip address 192.168.9.121 255.255.255.0 no shut exit ! interface gi 0/2 no shut Map switch default management-out-band switchport Pvid 9 exit
•
ip route 0.0.0.0 0.0.0.0 192.168.9.254
• • • • • • • • • •
• •
• •
exit vlan 9 management
Cont’ Step 2: connect to Gi 0/2 Log in using the new IP details config t vlan 1 no ports exit interface gi 0/1 no management shut exit vlan 2 no ports exit interface vlan 2 no ip address 192.168.1.1 exit • • • • • • • • • • • • • • • • • • • • • • • • • • •
no vlan 2 exit interface range gi 0/1-2 switchport priority default 3 no shut exit interface radio 0/1 switchport priority default 3 no shut exit config save end
Questions: 1. How do they change the IP address of computer? 2. Describe the steps to check the ODU configuration with IDU eclipse GE3. 3. Describe the steps to change the IP address of IDU Eclipse edge and GE3. 4. Describe the steps to check the performance and traffic on the port. 5. How many options of logging on CTR 8300? And describe the steps. 6. What is the command to show VLANs in CTR 8300? 7. What is the command to show the Mac- address table in CTR 8300?
Reminder •
•
please download Team viewer for future remote assistance on: http://www.teamviewer.com/ Have Putty on your PC