Defence Science Journal, Vol. 60, No. 5, September 2010, pp. 551-563 Ó 2010, DESIDOC
REVI RE VIEW EW
PAPER AP ER
Defence Applications of Polymer Nanocomposites
R.V. R.V. Kurahatti Kura hatti *, A.O. Surendranathan#, S. A. Kori*, Nirbhay Singh, A.V. A.V. Ramesh Rames h Kumar , and Saurabh Srivastava *Basaveshwar Engineering College, Bagalkot-587 102 National Institute of Technology Karnataka, Surathkal-575 025 Defence Materials and Stores Research & Development Establishment, Kanpur-208 013 E-mail: *
[email protected] #
ABSTRACT
The potential opportunities promised by nanotechnology for enabling advances in defence technologies are staggering. Although these opp ortunities are likely t o be realised over a few decades, many advantages are currently being explored, particularly for defence applications. This review provides an insight into the capabilities offered by nanocomposites which include smart materials, harder/lighter platforms, new fuel sources and storage as well as novel medical applications. It discusses polymer-based polymer-based nanocomposite materials, nanoscale fillers and provides examples of the actual and potential uses of nanocomposite materials in defence with practical examples. Nanocomposites, nanotechnologies, nanotechnologies, defence applications, applications, smart materials, materials, polymer-based polymer-based nanocomposites, nanocomposites, Keywords: Nanocomposites, medical applications, fuel sources 1.
INTRODUCTION
Nanotechn Nano technologi ologies es promise prom ise revolutio revo lutionary nary techno te chnologic logical al changes for a wide range of military applications and platforms. platforms. Technologies Technologies to be be incorporated incorporated within the platforms which are directly relevant to the defence arena include: aerodynamics, mobility, stealth, sensing, power generation and management, smart structures and materials, resilience and robustness, etc. In addition, nanotechnologies will have impact on battlespace systems concerned with information and signal processing, autonomy and intelligence. With regard to information technology, in particular, substantial advantages are expected to be gained from these new enabling capabilities which include threat detection, novel electronic displays and interface systems, as well as a pivota piv otall role rol e for the t he devel de velopme opment nt of mini m iniatu aturis rised ed unman un manned ned autonomous vehicles (UAVs) and robotics. Nanotechnology will enable the development of novel materials providing the basis for the design and development of new properties and structures which will result in increased performance (e.g., nano-energetics and new types of catalysts), reduced cost of maintenance (e.g., wear reduction, self-healing and self-repair), enhanced functionality (eg adaptive materials) and new types of electronic/opto-electronic/magnetic material pro perti pe rti es. es . 2. POL POLYMER YMER NAN NANOC OCOM OMPO POSI SITE TES S 2.1 Defi Defini niti tion on
The reinforcement of polymers using fillers, whether inorganic or organic, is common in the production of modern plas pl asti tics cs.. Poly Po lyme meric ric nano na noco comp mpos osit ites es (PNC (P NCs) s) repr re pres esen entt a
radical alternative to the conventional filled polymers or polymer poly mer blends bl ends.. In contra co ntrast st to conve co nventio ntional nal system sy stems, s, where wh ere the reinforcement is of the order of microns, PNCs are exemplified by discrete constituents of the order of a few nanometers (<100 nm) in at least one dimension (Fig. 1). The small sise of the fillers leads to an exceptionally large interfacial area in the composites. The interface controls the degree of interaction between the filler and the polymer and thus controls the properties. As in conventional composites, the interfacial region is the region beginning at the point in the fibre at which the properties differ from those of the bulk filler and ending at the point in the matrix at which the properties become equal to those of the bulk matrix 1. FIBRE FILLER < 100 nm
~ 1 nm
PLATE-LIKE FILLER
3-D FILLER
< 100 nm
Figure 1. Schematic of nanoscale fillers.
Received 24 April 2009, Revised 27 January 2010
551
DEF SCI J, VOL. 60, NO. 5, SEPTEMBER 2010
It can be a region of altered chemistry, altered polymer chain mobility, altered degree of cure, and altered crystallinity. Interface size has been reported to be as small as 2 nm and as large as about 50 nm. Even if the interfacial region is only a few nanometer, very quickly the entire polymer matrix has a different behaviour than the bulk. If the interfacial region is more extended, then the polymer matrix behaviour can be altered at much smaller loadings . To implement the novel properties of nanocomposites, processing methods that lead to controlled particle size distribution, dispersion, and interfacial interactions are critical. 2.2 Classification
Polymeric nanocomposites can be broadly classified as
Nanoclay-reinforced composites Carbon nanotube-reinforced composites Nanofibre-reinforced composites, and Inorganic particle-reinforced composites.
2.2.1 Nanoclay-reinforced Composites
Historically, the term clay has been understood to be made of small inorganic particles (part of soil fraction < 2 mm), without any definite composition or crystallinity. The clay mineral (also called a phyllosilicate) is usually of a layered type and a fraction of hydrous, magnesium, or aluminum silicates 6 . Every clay mineral contains two types of sheets, tetrahedral ( T ) and octahedral ( O ) 6. For a better understanding the major clay mineral groups along with their ideal structural chemical compositions are listed in Table 1. Hectorite, saponite, and montmorillonite are the most commonly used smectite type layered silicates for the preparation o f nanocomp osite s. Mon tmo rillonite (MMT ) has the widest acceptability for use in polymers because of their high surface area, and surface reactivity 7. It is a hydrous aluminosilicate clay mineral with a 2:1 expanding layered crystal structure, with aluminum octahedron sandwiched between two layers of silicon tetra hedron. Each layered sheet is approximately 1 nm thick (10 Å), the lateral dimensions of these layers may vary from 30 nm to several microns or larger, depending on the particular layered silicate. The aspect ratio is about 101000 and the surface area is in the range 6 of 750 m 2/g. When one octahedral sheet is
bonded to one tetrahedra l she et, a 1:1 clay miner al re sults. The 2:1 clays are formed when two tetrahedral sheets bond with one octahedral sheet 6,7 . The aspect ratio of 1000 is possible when a clay platelet is well-disp ersed into the polymeric matrix without breaking. Practically, breaking up of clay platelets during mixing process at high shear and large shear stress condition results in an aspect ratio of 30300. Graphite has a similar geometry (layered structure) with nanoclay, therefore a clay-polymer reinforcement concept is applicable 8. Graphite flakes have been known as host materials for intercalated compounds. By applying rapid heating, some of the graphite-intercalated compounds (GICs) expand and a significant increase in volume takes place. Many literature citations identify the expanded graphite flakes with polymer systems for lightweight and conductive polymer compo sites 9-13 . In polymer-layered silicate (PLS) nanocomposites, stacking of the layers leads to a regular van der Waals gap between the layers called the interlayer or gallery. Isomeric substitution (for example tetrahedral Si 4+ by Al 3+ or octahedral Al 3+ by Mg 2+ or Fe 2+ ) within the layers generates negative charges that are counterbalanced by alkali and alkaline earth cations (typically Na + or Ca 2+) situated inside the galleries 7 . This type of layered silicate is characterised by a moderate surface charge known as the cation exchange capacity (CEC). Details regarding the structures and chemical formulae of the layered silicates are provided in Fig. 2. In general, the organically modified silicate nanolayers are referred to as nanoclays or organosilicates 4 . It is important to know that the physical mixture of a polymer and layered silicate may not form nanocomposites 7 . Pristine-layered silicates usually contain hydrated Na + or K + ions 7. To render layered silicates miscible with other polymer matrices, it is required to convert the normally hydrophilic silicate surface to an organophilic one, which can be carried out by ion-exchange reactio ns with cationic surfactants 7. . O) Sodium montmorillonite ( Na x( Al 2- xMg x)(Si4O10)(OH )2 H 2 type layered silicate clays are available as micron size tactoids, which consist of several hundreds of individua l plate-like structures with dimensions of 1 m m ´ 1 m m ´ 1 nm. These are held together by electrostatic forces (gap in between two adjacent particles ~ 0.3 nm). The MMT particles, which are not separated , are often referred to
Table 1. Classification and example of clay minerals 5.
552
Structure
Group
Mineral examples
Ideal composition
Basal spacing (Å)
2 : l(TOT)
Smectite
Montmorillonite Hectorite Saponite
[( Al 3.5-2.8 Mg 0.5-0.2)(Si8)O20 (OH )4] Ex0.5-0.2 [( Mg 5.5-4.8 Li0.5-1.2)(Si8) O20 (OH )4] Ex0.5-0.2 [( Mg 6 )(Si7.5-6.8 Al 0.5-1.2 O20 (OH )4] Ex0.5-0.2
12.4-17.0
2 : l(TOT)
Illite
Illite
[( Al 4) (Si7.5-6.8 Al 0.5-1.2) O20 (OH )4 ] K 0.5-1.5
10.0
2 : l(TOT)
Vermiculite
Vermiculite
[( Al 4) (Si8.8-8.2 Al 1.2-1.8) O20 (OH )4]Ex1.2-1.8
9.3-14.0
1 : l(TOT)
Kaolin serpentine
Kaolinite dickite, nacrite
Al 4Si4Ol0(OH )8
7.14
KURAHATTI, et al.: DEFENCE APPLICATIONS OF POLYMER NANOCOMPOSITES
TETRAHEDRAL G N I
~ 1 nm OCTAHEDRAL
C A P S L A S A B
TETRAHEDRAL
EXCHANGEABLE
CATIONS Al , Fe , Mg , Li OH O Li, Na, Rb, Cs
Figure 2. Basic structures of 2:1 clay minerals 7,14.
as tactoids. The most difficult task is to breakdown the tactoids to the scale of individual particles in the dispersion process to form true nanocompo sites, which has been a critical issue in current research in different literatures 3, 15-24 . 2.2.1.1 Properties and Applications
high (>200 per cent) even at reinforcement loadings of 3 per cent. But even a small amount of aggregation decreased the strain-to-failure ratio to 5 per cent-8 per cent. A similar effect was also observed in polyimide matrices, in which the strain-to-failure ratio decreases by 72 per cent due to aggregation. A significant improvement in flexural modulus (1.5 GPa to 2.1 GPa) and tensile strength (29 MPa to 40 MPa) and impact strength (18 J/m to 24 J/m) of PP/clay nanocomposites is reported on addition of about 15 per cent PP-g-MAH to PP-organoclay system 16 . Xu 68 , et al . have reported similar improvements in tensile strength and impact strength of the composites with a nanoclay addition of 10 per cent to 15 per cent. Unprecedented combinations of properties have been observed in some thermoplastics too. The inclusion of equi-axed nanoparticles in semicrystalline thermoplastics has resulted in increase in yield stress, the tensile strength, and Youngs modulus of the polymers. A volume fraction of only 0.04 mica-type silicates (MTS) in epoxy increases the modulus below the glass transition temperature by 58 per cent and the modulus in the rubbery region by 450 per cent. In addition, the permeability of water in poly (å -caprolactone) decreases by an order of magnitude with the addition of 4.8 per cent silicate by volume. Yuno 17 , et al . showed a 50 per cent decrease in the permeability of polyimides at a 2 per cent loading of MTS. Many of these nanocomposites are optically transparent and/or optically active.
Theoretical predictions have shown that the modulus for well aligned platelets can be three times that for wellaligned fibres, especially as the aspect ratio of clay layers increases 14. Other studies however, suggest that the modulus increase is not entirely due to the load-carrying ability 2.2.2 Carbon Nanotube-reinforced Composites of the platelets, but is caused by the volume of polymer Micrometer-size carbon tubes, which are similar in constrained by the platelets 14. This suggests that to optimise structure (but not in dimensions) to the recently discovered the increase in modulus, the degree of dispersion must multi-walled carbon nanotubes, were first found in 1960 be optimised to maximise the degree of matrix/filler interaction. by Roger Bacon 26. These nanosised, near-perfect whiskers Work on PP nanocomposites in which adding malefic anhydride (termed nanotubes) were first noticed and fully characterised (MA) to the matrix changed the degree of filler dispersion in 1991 by Sumio Iijima 25 of NEC Corporation in Japan. supports this suggestion that despite the plasticising effect of MA, the modulus improved due to enhanced dispersion of the clay 107 . Lan and Pinnavaia 108 found that, as the degree of exfoliation increased by chan ging the le ngth of alkyla mmonium LAYERED intercalating chain, the modulus and strength POLYMER SILICATE improved. As the polymer intercalates and swells, the layers and the area of interaction between the polymer and the filler increases and the modulus increases significantly. Figure 3 represents three main types of composites for layered silicate materials. The polymer/clay interaction plays a significant role in controlling mechanical behaviour is also evident from the fact that improvement in properties tends to be higher above the glass transition temperature than below it 15. However, PHASE SEPERATED proper dispersion is critical for achieving thi s. (MICROCOMPOSITE) Hasegawa 37 , et al . studied the dispersion of INTERCALATED EXFOLIATED (NANOCOMPOSITE) (NANOCOMPOSITE) clays in polypropylene. They found that the strain-to-failure ratio in nanocomposites remains Figure 3. Scheme of three main types of layered silicates in polymer matrix 5. 553
DEF SCI J, VOL. 60, NO. 5, SEPTEMBER 2010
He was investigating the surface of carbon electrodes used in an electric arc discharge apparatus that had been used to make fullerenes. Several exciting developments have taken place in this field since then 27 . The first nanotubes observed were multi-walled nanotubes (MWNT). MWNTs consist of two or more concentric cylindrical shells of graphene sheets coaxially arranged around a central hollow core with interlayer separati on, as in graphite (0.34 nm) 28 . In contrast, single-shell or single-walled nanotubes 29,30 (SWNT) are made of single graphene (one layer of graphite) cylinders and have a very narrow size distribution (12 nm). Often many (tens) single-shell nanotubes pack into larger ropes. Figure 4 shows electron micrographs of SWNT and MWNT. Both types of nanotubes have the physical characteristics of solids and are microcrystals, although their diameters are close to molecular dimensions. In nanotubes, the hexagonal symmetry of the carbon atoms
in planar graphene sheets is distorted, because the lattice is curved and must match along the edges (with dangling bonds) to mak e perfect cylin ders. This leads to a helical arrangement of carbon atoms in the nanotube shells. Depending on the helicity and dimensions of the tubes, the electronic structure changes considerably 31, 32 . Hence, although graphite is a semi-metal, carbon nanotubes (CNTs) can be either metallic or semiconducting. Nanotubes are closed by fullerenelike end caps that contain topological defects (pentagons in a hexagonal lattice). The electronic character of the ends of these tubes differs from the cylindrical parts of the tubes and is more metallic due to the presence of defects in these regions 33 . The discovery of nanotubes has complemented the excitement and activities associated with fullerenes 34 . Although fullerenes have fascinating physica l pr operties, their r elevance in t he nanocomposite field is limited. The properties of CNTs are unique compared to other graphite fibres. Their structure remains distinctly different from that of traditional carbon fibres 2, which have been used industrially for several decades (e.g., as reinforcements in tennis rackets, airplane body parts and batteries). Nanotubes represent the ideal, most perfect, ordered carbon fiber, the structure of which is entirely known at the atomic level. Table 2 shows measured and theoretical properties of both SWN T and MWNT. 2.2.2.1
Properties and Applications Qian 11, et al . and Yu44 , et al . have shown, as first
(a )
(b)
Figure 4. (a) HRTEM image showing the SWNT in bundles, (b) HRTEM images of a MWNT along its length and at the end.
described by Wagner 61 , that MWNTs fail via a sword-andsheath mechanism. This situation limits the efficiency of MWNT/polymer composites because only a small portion of the volume fraction of the MWNT carries load. Evidence for this was shown for MWNT/polystyrene composites 18 , in which the effective modulus of the MWNT in the composite was only 500 GPa but the measured modulus of the MWNT
Table 2. Theoretical and experimentally measured properties of carbon nanotubes Property
Nanotubes
Graphite
Lattice structure
Planar hexagonal. plane-to-plane distance = 0.335
Resistivity Thermal conduc tivity
(Cylindrical) hexagonal lattice helicity Nanotubes: ropes, tube s arranged in triangular lattice with lattice param eters of a= 1.7 nm, tube-tube distance=0.315 0.8 - 1.8 g cc-1 (theoretical) ~ 1 TPa for SWNT ~ 0.3-1 TPa for MWNT ~50-500 GPa for SWNT, 10-60 GPa for MWN T 5-50 micro-ohm -cm 3000 Wm -1k -1 (theoretical)
Thermal expansion
Negligible (theoretical)
Oxidation in air
> 700 °C
Specific gravity Elastic modulus Strength
554
2.26 g cc-1 1 TPa ( in plan e) 50 (in plane) 50 (in plane) 3000 Wm -1K -1 (in plane) 6 Wm -1k -1 (c axis) -1´ 10-6 K -1 (in plane) 29´10-6 K -1 (c axis) 450-650 °C
KURAHATTI, et al.: DEFENCE APPLICATIONS OF POLYMER NANOCOMPOSITES
is close to 1 TPa. Therfore, to minimise the number of layers not carrying load, 2-3 layers are preferable. In addition, CNTs are over 105 times more resistant to the electron radiation than polyethylene and about 103 times more resistant than highly radiation-resistant rigid-rod polymers 18 such as poly(p-phenylene benzobisoxazole). For SWNT composites, the SWNT are in a bundle and individual SWNTs may slip within the bundle. Work by Yu44 , et al . showed that if only the nanotubes on the outer edge of a SWNT in a bundle are used to calculate the modulus, it is close to the predicted 1 TPa. However, if the whole area of the bundle is used, the calculated modulus is considerably lower. This suggests that, u nless the SWNTs are isolated from the bundles, the modulus of the composites made from these materials will be limited. Some promising results have been reported by Biercuk and others 41 . They observed a monotonic increase of indentation (Vickers hardness) by up to 3.5 times on loading up to 2 per cent SWNTs and a doubling of thermal conductivity with 1 per cent SWNTs. Also, 1 per cent MWNT loading in polystyrene increases the modulus and breaking stress by up to 42 and 2 5 per cent, r espectively 41 . Similarly, the strength of 1 per cent PS/MWNTs is found to increase by 25 per cent (13-16 MPa) and strain at yield by 10 per cent42. One of the major benefits expected from incorporating CNTs in polymers is an increase in both the electrical and thermal properties of polymers. The electrical characteristic of interest in polymers is percolation threshold . For CNTs/ epoxy system a very low percolation threshold of below 1 per cent is reported. Likewise, the electrical conductivity of CNTs/PMMA composites is reported to increase by about nine times with the add ition of 5-8 per cent CNTs. While the polystyrene is insulating, the films doped with MWNTs are conducting (conductivity 7.1 ´ 10 -2 Ohm -1cm -1 ). Electrical conductivity 31 of 0.5 per cent MWNT/PFA is 1.3 ´ 10 -2 Ohm1cm -1 . 2.2.3 Nanofiber-reinforce d Composites
Carbon nanofibers (CNF) are a unique form of vapourgrown carbon fibres that fill the gap in physical properties between conventiona l car bon fibres ( 510 µm) and carbon nanotubes (110 nm). The reduced diameter of nanofiber pro vides a larger surfa ce a rea with s urf ace functiona litie s in the fiber 55 . Typically CNF are not concentric cylinders; the length of the fibre can be varied from about 100 µm to several cm, and the diameter is of the order of 100 200 nm with an average aspect ratio greater than 100. The most common structure of CNF is the truncated cones, but there are wide ranges of morphologies (cone, stacked coins, etc). CNF have the morphology where these are hollow at the centre (much like a MWNT) and have a larger diameter than MWNT but the individual layers are not arranged in concentric tubes. 2.2.3.1
Properties and Applications
Tandon and Ran 56 enhanced the thermomechanical properties of conventional aerospace carbon fibre-reinforced
(IM7) composites using carbon nanofiber. They manufactured IM7/CNF matrix unidirectional laminate aerospace structures using the filament-winding technique. Glasgow and Tibbetts 57 oxidised the surface of carbon nanofiber to improve the tensile behaviour in PP composites. Lafdi and cowork ers 58 showed improved flexural strength and modulus in epoxy based composites with oxidised nanofibres. Finegan and Tibbetts 59 incorporated CNF in a PP with improved strength and stiffness. Thermal transport across bonded radiator panels is important wher e the rmally-condu ctive adhesives play an important role. Electrically-conductive bonded joints are needed in spacecraft to eliminate the build up of static charge on the structure due to the impingement of charged particles. Gibson 60, et al . modified the epoxy-based adhesives formulated with silver-coated and uncoated vapour-grown carbon nanofibers for several aerospace applications such as electrical conductivity, thermal transport, and mechanical properties. But they concluded that it does not help to remove the waste heat 60 . Lao54 , et al . used CNF, clay platelets, and sili ca nanoparticles to find the relat ionship between the flamm ability and mechanical properties of nylon-11. They achieved a combination of enhanced mechanical and flammability properties in clay platelets and CNF. In their analysis, clay-based nanocomposites showed better flammability, while the CNF-based nanocomposites showed better mechanical properties. 2.2.4 Inorganic Particle-reinf orced Composites
Nanoparticles are often defined as partic les of < 100 nm in diameter 61 . Nanometer-sized particles have been made from different organicinorganic particles and these impart improved properties to composite materials 51. Different particles have been used to prepare polymer/inorganic particle nanocompo sites, inclu ding: Metals ( Al , Fe , Au , Ag , etc.) Metal oxides ( ZnO , Al 2 O3 , CaCO 3 , TiO 2, etc.) Nonmetal oxide ( SiO 2) 52 Other ( SiC ) The selection of nanoparticles depends on the desired thermal, mechanical, and electrical properties of the nanocomposites. For example, Al nanoparticles are often selected due to their high conductivity; calcium carbonate ( CaCO 3) particles are chosen because of their low cost and silicon carbide (SiC) nanoparticles are used because of their high hardness, corrosion resistance, and strength 53 . 2.2.4.1
Properties and Applications
Polymer/inorganic particle-based nanocomposites have shown significant improvement in mechanical, thermal, and electrical properties. For example, in nylon-6 filled with 5 Wt % 50 nm silica nanoparticles, an increase in tensile strength by 15 per cent, strain-to-failure by 150 pe r ce nt , Young s mo du lu s by 23 pe r ce nt an d im pa ct strength by 78 per cent were reported 62 . Jiang, 63 et al . investigated ABS (acrylonitrile butadiene styrene) reinforced with both microsized and nanosized calcium carbonate pa rt ic le s th ro ug h me lt co mp ou nd in g. It wa s fo un d th at 555
DEF SCI J, VOL. 60, NO. 5, SEPTEMBER 2010
the ABS/micron-sized particle composites had higher Youngs modulus but lower tensile and impact strengths than neat ABS. However, the ABS/nano-sized particle composites increased the Youngs modulus as well as impact strength. Ma 65 , et al . showed an improvement in electrical properties of polyethylene nanocomposites by in tr od uc in g f un ct io na l g ro up s a t TiO 2 nanoparticles. Zhang and Singh 67 improved the fracture toughness of nominally brittle polyester resin systems by incorporating Al 2O 3 (15 nm). An Al 2 O 3 particle has been found to be effective in improving the dielectric cons tant of a polymer in other studies 64 also. Koo 48-50, et al . used AEROSIL (silicon dioxide, 740 nm) silica nanoparticles to process different nanocomposites with different resin systems (phenolic, epoxy, cyanate ester) for high-temperature applications. Recently, creep tests were performed on TiO 2 /PA6,6 nanocompo sites by Zhang and Yang 47 . Poor creep resistance and dimensional stability have been improved by adding TiO 2 in polyamide 6,6 thermoplastic composites. Chisholm 55 , et al . investigated micro- and nano-sized SiC in an epoxy matrix system. In their study, an equal amount of loading, nanoparticle infusion brings superior thermal and mechanical properties than microsized pa rt ic le -b as ed co mp os it es . 3.
NANOCOMPOSITESDEFENCE APPLICATIONS
In materials technology, there are relatively few examples of nanocomposites developed specifically for defence applications. 3.1 High Performance Fibre/Fabrics
The first attempt to produce nanotubes resulted in very small quantities of tangled nanotubes, which however has created interest in these materials as non-oriented mats. Further developments had led to the development of techniques for spinning nanotubes into fibres in a polymer matrix, which is of special interest for mechanical and electronic fabric applications 69,70 . By infiltrating nanotube mats or woven fibres with a polymer, continuous sheets or films of a nanocomposite can be produced 71,72 . The nanotubes will contribute to mechanical properties (strength and stiffness) of the film as well as to electrical conductivity. The production of polymer fibres was until recently limited to extruding fibres of relatively large (micrometer diameter) sizes. Recently, an elctrospinning technique 73, 74 has been shown to be effective to produce pure polymer and polymer nanocomposite fibres with diameters in the range of 200 nm to 300 nm. More interesting is, in electrospun nanocomposite fibres, the nanoparticles were found to be highly aligned. This is likely to significantly effect the optical and mechanical properties, although no results were reported. For non-woven fabrics to achieve electrical conductivity, a simple and flexible method has been reported, where the non-woven mat was exposed to a high intensity light source (e.g., from a flash tube), whic h resulted in immediate 556
joining of fibres at cross-over points of contact. Using a mask, fibres can be joined in any desired pattern 73 . Such materials may find wide applications in defence as electrically conductive fabrics, sensors, electromagnetic shielding, microwave absorption, electrical energy storage (capacitors), actuators, and materials for micro UAVs. 3.2 Ballistic Protection
The reports of ballistic testing of PNCs are very few and this may be due to secrecy associated with such materials and lack of suitable nanocomposite materials. For light protection (body armour and vehicle liners) woven materials such as Kevlar are commonly used. It is likely that electrospun nanofibres, spun CNTs could be useful in such applications. There are few reports of the promising application of nanocomposites in body armour. Shear thickening fluids 74-77 consist of a fluid containing a dispersion of particles and this fluid stiffens and resists deformation if sheared rapidly by a n exter nal force . Repo rts from the U S Ar my Rese arch Laboratory indicate promising results when combining inorganic nanoparticles (of silica) in polyethylene glycol. When this shear thickening fluid is impregnated into conventional Kevlar, the ability of the material to absorb energy is greatly improved. In one example, the ballistic perfo rmance (in terms of absorb ed energy) was more than doubled so that four layers of Kevlar impregnated with the shear thickening fluid absorbed as much energy as would have been absorbed by 10 layers without the shear thickening fluid. This will lead to a more flexible armour with reduced weight. Such materials find applications for body/personal armour where flexibility of movemen t is required besides protection against blunt weapons (stones, sticks and bars) for arms and legs. 3.3 Microwave Absorbers
Nanocomposites as microwave absorbers are receiving much attention. Nguyen and Diaz 78 have reported a method to synthesize polypyrrole nanocomposites containing iron oxides ( g and a), tin oxide, tungsten oxide and titanium dioxide. Pyrrole containing a dispersion of nanoparticle metal oxides was polymerised in situ and the magnetic properties reported. The electrical conductivity and dielectric losses can be tu ned by va ry ing th e co ncen trat ion an d or ient atio n of the nanotubes additions. Glatowski 72 , et al . have been awarded a patent in this area, covering a wide range of thermoplastic and thermosetting matrices containing oriented nanotubes. Only a few weight per cent of nanotubes need be added to the polymer to achieve useful properties. Efforts have been made to utilise CNTs for developing economical microwave (in the range 8 GHz to 24 GHz) absorbers 103,104 . These materials have wide applications in electrical energy storage (condensers) integrated into load-carrying structures for UAVs, high strength CNTs po lymer fibres fo r ener gy ab sorp tion , electr omag ne tic shielding, etc.
KURAHATTI, et al.: DEFENCE APPLICATIONS OF POLYMER NANOCOMPOSITES
3.4 Refractive Index Tuning
In many optical applications such as telecommunications and optical computing, polymer optical fibres are very attractive to adjust the refractive index of the connecting optical fibre (due to ease of mass production and low cost). This can be done by the addition of nanoparticles with various refractive indices to the polymer. Bohm 79, et al . reported additions of nanoparticle zirconia, alumina, and silica to poly (methyl methacrylate) and they were able to adjust the refractive index over a sufficient range. Levels up to 10 Wt % loading were reported. Tuning the refractive index of surface coatings is important in signature management. Damage resistance (abrasion and scratching) of the fibre is likely to be improved by addition of ceramic nanoparticles.
when exposed to ã-radiation. This unexpected stability was attributed to two effects arising from nanoparticles additions. Firstly, flake-like clay particles act in a passive
mode to shield the polymer from radiation and secondly, nanoparticles act as active sink for broken polymer chains, which are grafted onto the nanoparticles surfaces. Recently Charati 97 , et al . revealed a method for manufacturing conductive composites. They first sonicated an organic polymer precursor (e.g., poly(arylene ether)) with SWNTs in an ultrasonicator to disperse the SWNTs and then polymerised the organic polymer precursor using shear and elongational forces. They claimed that in this way, at least a portion of the CNTs could be functionalised either at the side wall or hemispherical ends.
3.5 Solid Lubricants
3.8 Ultraviolet Irradiation Resistance
It is possible to produce inorganic fullerene-like (IF) nanoparticles of tungsten sulphide (WS 2), which have a characteristic structure like a hollow onion. Rapoport 80 , et al . have reported that by adding small quantities of WS 2 nanoparticles (about 100 nm dia) to two polymer matrices: epoxy and polyacetal, it was poss ible to reduce coefficient of dry friction between polymer and a steel disc to less than half in both the cases. If a simple lubricant was present, friction coefficient was further reduced significantly. Fracture toughness of the epoxy was also improved. These lubricants may be used for rotating and sliding bearings.
Common polymers are not stable under ultraviolet irradiation and will begin to degrade after few weeks. Strength and fracture toughness are drastically reduced and the polymer b ecomes brittle. Jiang 84 , et al . studied the effect of modifying the epoxy matrix by adding nanoparticles of titanium dioxide to epoxy/carbon fibre composite. They found that resistance to degradation by ultraviolet irradiation could be reduced by approximately half and mechanical properties (measured by interlaminar shear strength) could be imp roved by 80 per cent.
3.6 Porous Nanocomposites
The additions of nanoparticles can serve to improve the foaming properties of a polymer as reported by Siripurapu81, et al . who used additions of silica nanoparticles to act as nucleation sites for nanopore formation using carbon dioxide as a blowing agent. A disadvantage of porous polymer foams (e.g., polyu ret hane) is their lar ge surfaceto-volume ratios, which increase the rate of heat and gas release in case of fire. By introducing nanoparticles with a flake-like morphology, the rate of burning can be significantly reduced. Nanoporous polyurethane is being considered for automotive seat applications. Other applications include shock-absorbing materials, and acoustic absorbents, etc. 3.7 Electrostatic Charge Dissipation in Space Environment
Dissipation of static charge on spacecraft is a severe problem, which requires a material with not only sufficient electrical conductivity but also must be stable to the space environment (intense ultraviolet radiation, charged particle irradiation, atomic oxygen, rapid and severe temperature changes). Smith 82 , et al . working at NASA reported that the conductivity sufficient to eliminate static discharge could be achieved in a polyimide nanocomposite containing as little as 0.03 Wt % CNTs. Resistance to radiation of a styrene-butadiene-styrene/ clay nanoparticles nanocomposite has been investigated by Zhang83, et al . The nanocomposite w as virtually unaffected
3.9 Fire Retardation
Polymers have poor fire resistance. If ignited, most polymer s will burn quickly, rel easing large quantit ies of heat, toxic gases, and soot. Polymers containing a few weight per cent of nanoparticle clays have greatly improved fire resistance as reported by Gilman 85 , et al . The thermal pro perties of the PN C are improve d, melting an d dripp ing are delayed, and rate of burning is greatly reduced (by more than half). The presence of flake-like clay nanoparticles reduces the diffusion of polymer decomposition volatiles (the fuel) to the burning surface and reduces diffusion of air into the polymer. Further, addition of clay nanoparticles improves mechanical properties significantly. Similar improvements were noted in polypropylene/CNTs nanocomposites. High thermal conductivity of CNTs might increase heat input into polymer and enhance rate of burning. However, Kashawagi 86 , et al . contradict this observation in CNTs. Examples of applications include reduction of fire risk in enclosed spaces in vehicles, submarines, aeroplanes, and ships. 3.10 Corrosion Protection
Corrosion protection of metals and alloys is normally achieved by a surface coatings which must resist both mechanical damage (scratching, impact, abrasion) and chemical attack (salts, acids and bases, solvents). It should also not be damaged (cracked) by having a coefficient of thermal expansion greatly different from the metal to be protected. PNCs have improved scratch and abrasion resistance, due to their higher hardness combined with improved elastic 557
DEF SCI J, VOL. 60, NO. 5, SEPTEMBER 2010
modulus. Gentle and Baney 87 reported preliminary experiments using a silica-reinforced silicone nanocomposite coating deposited to protect aluminium surfaces and electronic circuits. A significant improvement during salt fog testing was obtained with survival rates improved by up to 100 times 87 . Corrosion protection in aerospace (at normal or low temperatures, not suitable above 150 °C) and corrosion protection of electronic circuits demand such materials. 3.11 Signature Reduction
This is a field which is surrounded in secrecy. Dynamically tuneable camouflage materials would be an invaluable aid to defence operations, allowing personnel and equipment to achieve a highly visible or totally concealed presence depending on the situation. DeLongchamp and Hammond report a high-contrast electrochromatic nanocomposite ba se d on po ly (e th yl en ei mi ne ) an d Pr us si an Bl ue nanoparticles87. It is claimed that a fully switchable reflective tri-colour space coating has been produced. This material has obvious applications in dynamically tuneable camouflage in the visual spectrum. 3.12 Diffusion Barriers
Food packaging is dependent on preventing diffusion of gases and odours in airtight packets. Many tetra-pack and similar liquid containers consist of several layers, including a layer of aluminium as an impervious barrier to prevent carbon dioxide or oxygen spoiling the contents. The US Army is field-testing individual ready-to-eat food portions packaged in a nanocompo site container 108 . The food is claimed to remain fresh for three years. A lso linked to barrier properties are fire resistance and corrosion protection of nanocomposites. Food containers, fuel containers, gastight containers which are presently made of rubber or similar elastomers. 3.13 Sensors Kong99 , et al . demonstrated chemical sensors based
on individual SWNTs. They found that electrical resistance of a semiconducting SWNT changed dramatically upon exposure to gas molecules such as NO 2 or NH 3. The existing electrical sensor materials including carbon black polymer composites operate at high temperatures for substantial sensitivity whereas the sensors based on SWNT exhibited a fast response and higher sensitivity at room temperature. Ajayan 100 , et al . developed a controlled method of producing free-standing nanotube-polymer composite films that can be used to form nanosensor, which contains at least one conductive channel comprising an array of aligned CNTs embedded in a matrix (e.g., poly (dimethylsiloxane)). This material can be used to determine a real time physical condition of a material, such as that of an airplane wing or chassis while the airplane is in flight 87 . Such materials may be used for detection and identification of toxic gase s such as chemical warfare agents, flammable gases, solvent vapours, etc., touch sensors for interaction between operators and machines. 558
3.14 Actuators
Nanocomposite-based actuators have r educed p ower requirements and linear motion directly. Koerner 109 , et al . dispersed a small amount (<5 vol per cent) CNTs in a polyurethane thermoplastic polymer (Morthane) and found that the resultant nanocomposite could store (and release when required) 50 per cent more strain energy than the unreinforced polymer. The addition of CNTs allowed indirect (infrared) or direct (Joule heating) activation. Compared to conventional additives (e.g. carbon black), considerable lower additions of CNTs was required. Existing shape memory polymers are insufficiently strong (low recovery stress) to find wider application. By adding a mechanical restrain in the form of inert silicon carbide nanoparticles to a commercial shape memory polymer, Gall 88 , et al . were able to increase the recovery stress by 50 per cent, without degrading other properties. Courty 101 , et al. reported a novel actuator response driven by an electric field due to the presence of MWNTs in nematic elastomer, polysiloxane. They produced a composite material with embedded and aligned CNTs with an effective dielectric anisotropy, many orders of magnitude higher than in the usual liquid crystals. Ounaies 102 , et al . developed technique for making actuating composite materials with polarisable moieties (e.g., polyimide) and CNTs. UAVs, especially microUAVs, may demand such actuators. 4.
PRACTICAL EXAMPLES AND DEVELOPMENTS
With regards to coatings and camouflage, BASF polymer researchers 89 are looking into nanoparticles with highly branched polyisocyanates. These coatings will offer superior abrasion resistance, anti-reflection, tailored refractive indices, prote cti on from corro sio n, and self- cle ani ng surfac es. Al l these properties are of immense interest to the defence arena. Toyota started using nanoco mposites in their bumpers making them 60 per cent lighter and twice as resistant to denting and scratching. Likewise, the Chevrolet Impala makes use of polypropylene side body mouldings reinforced with montmorillonite. These novel nanomaterials save on weight but enhance the hardness. Oxonica, are commercialising cerium oxide to improve the combustion efficiency. Savings in fuel use, storage are a vital asset in military scenarios. Kodak is producing organic light emitting diodes (OLED), colour screens (made of nanostructured polymer films) for use in car stereos and cell phones. In medical field, Angstro Medica has produced a nanoparticluate-based synthetic bone (Human bone is made of calcium and phosphate composite called H ydroxyapatite). By manipulating calcium and phosphate at the molecular level, the firm has created a patented material that is identical in structure and composition to a natural bone. I n addition, the combination of nanotechnology and genomics will lead to the development of new vaccines and treatments for genetically-based illnesses. M/s. Smith & Nephew markets an anti-microbial dressing covered with nanocrystalline silver. The nanocrystalline coating of silver rapidly kills
KURAHATTI, et al.: DEFENCE APPLICATIONS OF POLYMER NANOCOMPOSITES
a broad spectrum of bacteria in as little as 30 min. Nanocubes made of organometallic network materials, currently being analysed by BASF researchers, could prove a suitable storage medium for hydrogen. Their three-dimensional lattice structure has numerous pores and channels, making nanocubes an ideal storage medium. 5.
INDIAN SCENARIO
India has initiated focused efforts on nanotechnology only in 2001, i.e., 5-7 years after countries like USA, EU, Japan, Korea, and Taiwan started their own programmes. The application-oriented research in India in the last few years has focused primarily on energy, environment, and health-related areas. The invention of flow-induced electrical response in CNTs has direct relevance in biological and biomedical applications90. Indian Institute of Science (IISc) has transferred the exclusive rights of this technology to an American start-up to commercialise the gas-flow sensors. Nanocrystalline gold triangles developed by a group at National Chemical Laboratory (NCL), Pune has been shown to be useful for cancer treatment by hyperthermia, where irradiation of the cancer cells is carried out by infra-red radiation 91 . These materials are used in insulin delivery for advanced diabetics. A research Group at Banaras Hindu University, has developed a novel method to produce a membrane out of CNTs for treating contaminated drinking water 92 . Eureka Forbes, in collaboration with IIT Madras, Chennai; has come out with a nanosilver-based water filter for the removal of dissolved pesticides in drinking water 93 . International Advanced Research Centre Powder Metallurgy and New Materials (ARCI), Hyderabad has the synthesis facilities to produce a wide range of metallic, ceramic and cermet nanopowders in large quantities. ARCI has developed the low-cost nanosilver-coated ceramic candle for disinfection of drinking water 94 . It has developed the lightening arresters based on ZnO microcrystalline powders 95 . Though, the speed of scientic research has increased considerably over the years 96 in terms of number of quality publications in technical journals, India still lags behind countries like Korea, China, and Taiwan, leave alone the leading countries like USA, Japan, and Europe. In application development and commercialisation of nanomaterials-based technologies, India is far behind even when compared to countries like Singapore. Both the government and industry need to ramp up their eorts in this area dramatically and immediately. 6.
CONCLUSIONS
It may well be predicted that PNCs in the mid- and longer-term will pervade all aspects of life, similar to the way plastics did in the last century. Clearly a diverse range of sectors such as aerospace, automotive, packaging, solar cells, electrical and electronic goods, household goods etc. will profit substantially from a new rang e of materials. In the short term (<5 years), the co mmercial impact may include inkjet markets, nanoparticles in cosmetics, and
automotive applications such as body moldings, engine covers and catalytic converts, batteries, computer chips. In the medium-term (<10 years), memory devices, biosensors for diagnostics, advances in lighting are all possible. The time-scale for automotive, aerospace, bio-nanotechnology is a long-term prospect (>15 years). To create macroscale materials, many issues surrounding the incorporation of nanotubes into a matrix, strategies for property improvement and the mechanisms responsible for those property improvements still remain critical. Since only a moderate success has been made over the last 20 years, researchers must continue to investigate strategies to optimise the fabrication of nanotube-enabled materials to achieve improved mechanical and transport properties. Defence needs to do a dedicated effort in areas such as signature management. Two major thrust areas in defence are nanocomposites to be used in heavily integrated multifunctional materials for UAVs and materials that enhance functionality and survivability of the individual soldier. ACKNOWLEDGEMENTS
Mr R.V. Kurahatti is thankful to Dr K.U. Bhasker Rao, Director DMSRDE for permitting to conduct p art of PhD research work in DMSRDE. Dr Nirbhay Singh, Dr A.V. Ramesh Kumar and Saurabh Srivastava are thankful to Dr K.U. Bhasker Rao, Director, DMSRDE for his help and encouragement. REFERENCES
1.
2. 3.
4. 5.
6. 7. 8.
Drzal, L.T.; Rich, M.J. & Koenig, M.F. Adhesion of graphite fibers to epoxy matrices: II. The effect of fiber finish. Journa l o f A dhesio n , 1983, 16 (2), 133152. Dresselhaus, M.S.; Dresselhaus, G.; Sugihara, K.; Spain, I.L. & Goldberg, H.A. Graphite fibers and filaments. Springer-Verlag, New York, USA, 1988. Usuki, A.; Kawasumi, M.; Kojima, Y.; Okada, A.; Kurauchi, T. & Kamigaito, O.J. Synthesis and structure of smectic clay/poly(methylmethacrylate) and clay/polystyrene nanocomposite via in situ intercalative polymerisation. Mate r. Res., 1993, 8 (5), 1174-178. Schmidt, D.; Shah D. & Giannelis, E.P. New advances in polymer/layered silicate nanocomposites. Curr. Opi. Solid State Mater. Sci. , 2002, 6 (3), 205-12. Alexandre, M. & Dubois, P. Polymer-layered silicate nanocomposites: preparation, properties and uses of a new class of materials. Mater. Sci. Engg. Rep. , 2000, 28 , 1-63. Scott, M.A.; Carrado, K.A. & Dutta, P.K. Handbook of layered materials, 2004. Ray, S.S. & Okamoto, M. Polymer/layered silicate nanocomposites: A review from preparation to processing. Progre ss Poly. Sc i. , 2003, 28, 1539-641. Shen, J.W.; Chen, X.M. & Huang, W.Y. Structure and electrical properties of grafted polypropylene/graphite nanocomposites prepared by solution intercalation. J. Appl. Pol y. Sc i. , 2003, 88 , 1864-869. 559
DEF SCI J, VOL. 60, NO. 5, SEPTEMBER 2010
9. 10. 11. 12. 13.
14.
15.
16.
17.
18.
19. 20. 21. 22. 23.
24.
560
Chung, D.D.L. Low-density graphite-polymer electrical conductors. US Patent No. 04704231, 1984. Chung, D.D.L. Composites of in-situ exfoliated graphite. US Patent No. 4946892, 1990. Wang, Y.S.; OGurkis, M.A. & Lindt, J.T. Electrical pro per ties of exfoliated-graphite fil led pol yet hyl ene composites. Polymer Com posit es, 1986, 7 (5), 349-54. Foy, J.V. & Lindt, J.T. Electrical properties of exfoliatedgraphite filled polyester based composites. Polymer Composites, 1987, 8 (6), 419-26 Celzerd, A.; McRae, E.; Mareche, J.F.; Furdin, G.; Dufort M. & Deleuze, C. Composites based on micron-sized exfoliated graphite particle: electrical conduction, critical exponents, and anisotropy. J. Phy. Chem. Solids , 1996, 57 (6-8), 715-18. Kawasumi, M.; Hasegawa, N.; Kato, M.; Usuki, A. & Okada, A. Preparation and mechanical properties of pol ypr opy len e-c lay hyb rid s. Macrom ole cules , 1997, 30(20) 6333-338. Kornmann, X.; Lindberg, H. & Berglund, L.A. Synthesis of epoxy-clay nanocomposites: Influence of the nature of the clay on structure. Pol yme r , 2001, 42 (4), 1303310. Kornmann, X.; Lindberg, H. & Berglund, L.A. Synthesis of epoxy-clay nanocomposites. Influence of the nature of the curing agent on structure. Polymer , 2001, 42(10), 4493-499. Becker, O.; Cheng, Y.B.; Varley, R.J. & Simon, G.P. Layered silicate nanocomposites based on various high functionality epoxy resins: the influence of cure temperature on morphology, mechanical properties, and free volume. Macromolec ules , 2003, 36(5), 1616625. Dennis, H.R.; Hunter, D.L.; Chang, D.; Kim, S.; White, J.L.; Cho, J.W. & Paul, D.R. Effect of melt processing conditions on the extent of exfoliation in organoclay bas ed nanocomposites. Poly mer , 2001, 42 (23), 9513522. Okada, A. & Usuki, A. The chemistry of polymer-clay hybrids. Mater. Sci. Eng., C: Bi omimetic Mater., Sens. and Syst., 1995, 3(2), 109-15. Lan, T.; Kaviratna, P.D. & Pinnavaia, T.J. Mechanism of clay tactoid exfoliation in epoxy-clay nanocomposites. Chem. Mat er. , 1995, 7 (11), 2144-150. Lan, T.; Kaviratna, P.D. & Pinnavaia, T.J. On the nature of polyimide-clay hybrid composites. Chem. Mater., 1994, 6(5), 573-75. Lan, T. & Pinnavaia, T.J. Clay-reinforced epoxy nanocomposites. Chem. Mater., 1994, 6(12), 2216-219. Vaia, R.A.; Jandt, Klaus, D.; Edward, J. K. & Giannelis, E.P. Microstructural evolution of melt intercalated po ly me r or ga ni ca ll y mo di fi ed la ye re d si li ca te s nanocomposites. Chem. Mater., 1996, 8(11), 2628635. Vaia, R.A.; Ishii, H. & Giannelis, E.P. Synthesis and properties of two-dimensional nanostructures by direct intercalation of polymer melts in layered silicates. Chem. Mate r. , 1993, 5 (12), 1694-696.
25. Iijima, S. Helical microtubules of graphitic carbon. Nature, 1991, 354 , 56. 26. Bacon, R. Growth, structure, and properties of graphite whiskers. J. Appl. Phys., 1960, 31 (2), 283-90. 27. Ebbesen, T.W. Carbon nanotubes: Preparation and pro per tie s. CRC Press , Boca Rat on, FL, 1997. 28. Ajayan, P.M. & Ebbesen, T.W. Nanometre-size tubes of carbon. Rep . Prog. Phys. , 1997, 60 (10), 1025-062. 29. Iijima, S. & Ichihashi, T. Single-shell carbon nanotubes of 1-nm diameter. Nat ure , 1993, 363 , 603-05. 30. Bethune, D.S.; Klang, C.H.; de Vries, M.S.; Gorman, G.; Savoy, R.; Vazquez, J. & Beyers, R. Cobalt-catalysed growth of carbon nanotubes with single-atomic-layer walls. Nature, 1993 , 363 , 605-07. 31. Mintmire, J.W.; Dunlap, B.I. & Carter, C.T. Are fullerene tubules metallic? Phys. Rev. Lett., 1992, 68 (5), 631-34. 32. Hamada, N.; Sawada, S. & Oshiyama, A. New onedimensional conductors: Graphitic microtubules. Phys. Rev. Lett., 1992 , 68 (10), 1579-581. 33. Carroll, D.L.; Redlich, P.; Ajayan, P.M.; Charlier, J.C.; Blase, X.; De Vita, A. & Car, R. Electronic structure and localized states at carbon nanotube tips. Phys. Rev. Lett ., 1997, 78 (14), 2811-814. 34. Kroto, H.W.; Heath, J.R.; OBrien, S.C.; Curl, S.C. & Smalley, R.E. C60: Buckminsterfullerene. Nature , 1985, 318 , 162. 35. Manias, E.; Chen, H.; Krishnamoorti, R.; Genzer, J.; Kramer, E.J. & Giannelis, E.P. Intercalation kinetics of long polymers in 2 nm confinements. Macromolecules , 2000, 33(21), 7955-966. 36. Ellis, T.S. & DAngelo, J.S. Thermal and mechanical properties of polypro pylene nanocomposites. J. App l. Poly m. Sci., 2002, 90 (6), 1639-647. 37. Hasegawa, N.; Kawasumi, M.; Kato, M.; Usuki, A. & Okada, A. Preparation and mechanical properties of polypropylene-clay hybrids using a maleic anhydridemodified polypropylene oligomer. J. Appl. Polym. , 1998, 67(1), 87-92 . 38. Becker, C.; Krug, H. & Schmidt, H. Tailoring of thermomechanical properties of thermoplastic nanocomposites by surface modification of nanoscale silica particles. In Proceedings of Materials Research Society Symposium, 1996, 435 , pp. 237. 39. Safadi, B.; Andrews, R. & Grulke, E.A. Multiwalled carbon nanotube polymer composites: Synthesis and characterization of thin films. J. Appl y. P oly m. Sci ., 2002, 84(14), 2660-669. 40. Watts, P.C.P.; Hsu, W.K.; Chen, G.Z.; Fray, D.J.; Kroto, H.W. & Walton, D.R.M. A low resistance boron-doped carbon nanotube-polystyrene composite. J. Mater. Chem., 2001, 11, 2482. 41. Biercuk, M.J.; Laguno, M.C.; Radosavijevic, M.; Hyun, J.K.; Johnson, A. T. & Fischer, J.E. Carbon nanotube composites for thermal management. Apply. Phys. Lett ., 2002, 80(15), 2767-69. 42. Benoit, J.M., Corraze, B. & Chauvet, O. Localization, coulomb interactions, and electrical heating in single-
KURAHATTI, et al.: DEFENCE APPLICATIONS OF POLYMER NANOCOMPOSITES
43. 44.
45.
46.
47. 48.
49.
50.
51.
52. 53.
54.
55.
56.
57.
wall carbon nanotubes/polymer composites. Phys. Rev. B, 2002, 65(24), 241405-09R. Blanchet, G.B.; Fincher, C.R. & Gao, F. Polyaniline nanotube composites: A high-resolution printable conductor. Appl. P hys . Lett ., 2003, 82(8), 1290-292. Yu, M.F.; Files, B.S.; Sivaram, A. & Rodney, R.S. tensile loading of ropes of single wall carbon nanotubes and their mechanical properties. Phys. Rev. Lett., 2000, 84(24), 5552-555. Yu, M.F.; Lourie, O.; Dyer, M.J.; Moloni, K.; Kelly, T.F. & Ruoff, R. S. Stren gth and breakin g mechanism of multiwalled carbon nanotubes under tensile load. Science , 2000, 287 , 637-40. Wagner, H.D.; Lourie, O.; Feldman, Y. & Tenne, R. Stress-induced fragmentation of multiwall carbon nanotubes in a polymer matrix. Appl. Phys. Lett., 1998, 72(2), 18890. Zhang, Z. and Yang, J.L. Creep resistant polymeric nanocomposites. Polyme r , 2004, 45, 3481-485. Koo, J.H.; Pilato, L.A. & Wissler, G.E. Polymer nanostructured materials for propulsion systems. In Proceedings of AIAA-2005-3606, 41st AIAA/ASME/SAE/ ASEE Joint Propulsion Conference & Exhibit, 1013 July 2005, Tucson, AZ, 2005. Koo, J.H.; Stretz, J.; Weispfenning, Z.; Luo, P. & Wootan, W. Nanocomposite rocket ablative materials: Subscale ablation test. In Proceedings of SAMPE Symposium, Long Beach, California, May 2004. Koo, J.H.; Pilato, L.A.; Wissler, G.; Lee, A.; Abusafieh, A. & Weispfenning, J. Epoxy nanocomposites for carbon fiber reinforced polymer matrix composites. In Proceedings of SAMPE Symposium, Covina, CA, 2005. Tang, J.; Wang, Y.; Liu, H.; Xia, Y. & Schneider, B. Effect of processing on morphological structure of polyacrylonitrile matrix nano- ZnO composites. J. Appl. Poly. Sci., 2003, 90 (4), 1053-057. Zheng, Y.P.; Zheng Y. & Ning, R.C. Effects of nanoparticles SiO 2 on the performance of nanocomposites. Mater ials Letters, 2003, 57 (19), 2940944. Hussain, F.; Hojjati, M.; Okamoto, M. & Gorga, R.E. Review article: Polymer-matrix nanocomposites, processing, manufacturing, and application: An overvie w. J. Comp. Mater., 2006, 40 (17), 1511-575. Lao, S.; Ho, W.; Ngyuen, K. & Koo, J.H. Flammabiltiy, mechanical, and thermal properties of polyamide nanocomposites. In Proceedings of SAMPE 2005, Seattle, WA, 2 005. Krishnan, Jayaraman; Kataki, M.; Yanzhong, Zhang; Xiumei, Mo. & Ramakrishna, S . Recent advances in polymer nanofibers. J. Nanos ci. Nanotech., 2004, 4(12), 52-65. Tandon, G.P. & Ran, Y. Influence of vapor-grown carbon nanofibers on thermomechanical properties of graphiteepoxy composites. In Proceedings of the 17 th Annual Technical Conference ASC, 2002. Glasgow, D.G. and Tibbetts, G.G. Surface treatment of carbon nanofibers for improved composite mechanical
58. 59.
60.
61.
62.
63.
64.
65.
66.
67. 68. 69.
70.
71. 72.
properties. In Proceedings of SAMPE 2004, Longbeach, CA, 2004. Lafdi, K. Carbon foam for thermal management. In Proceedings of SAMPE 2003, Dayton, OH, 2003. Finegan, C.; Tibbetts, G.G.; Glasgow, D.G.; Ting, J.M. & Lake, M.L. Surface treatments for improving the mechanical properties of carbon nanofiber/thermoplastic composites. J. Mater. Sci., 2003, 38 (16), 3485-490. Gibson, T.; Rice, B.; Ragland, W.; Silverman, E.M.; Peng, H. & Strong, K.L. Formulation and evaluation of carbon nanofiber-based conductive adhesives. In Proceedings of SAMPE 2005, Long Beach, CA, 1-5 May 2005. Wagner, H. D.; Lourie, O.; Feldmana, Y. & Tenne, R. Stress-induced fragmentation of multwall carbon nanotubes in a polymer matrix. Appl. Phys. Lett ., 1998, 72(2), 18890. Ou, Y.; Yang, F. & Yu, Z. A new conception on the toughness of nylon 6/silica nanocomposite prepared via in situ polymerization. J. Polym. Sci., Part B: Polym. Phys ., 1998, 36 (5), 789-95. Jiang, L.; Lam, Y.C.; Tam, K.C.; Chua, T.H.; Sim, G.W. & Ang, L.S. Strengthening acrylonitrile-butadiene-styrene (ABS) with nanosized and micronsized calcium carbonate. Polyme r , 2005, 46(10), 243-252. Lopez, L.; Song, B.M.K. & Hahn, H.T. The effect of particle size in alumina nanocomposites. In Proceedings of 14th Conference of ICCM, San Diego, CA, 14-18 July 2003. Ma, D.; Hugener, T.A.; Siegel, R.W.; Christerson, A.; Martensson, E.; Önneby, C. & Schadler, L.S. Influence of nanoparticle surface modification on the electrical be ha vi or of po ly et hy le ne na no co mp os it es . Nanote chnology, 2005, 16 (6), 724-31. Chisholm, N.; Mahfuz, H.; Rangari, V.K.; Ashfaq, A. & Jeelani, S. Fabrication and mechanical characterization of carbon/SiC-epoxy nanocomposites. J. Compo. Struc. , 2005, 67(1), 115-24. Singh, R.P. & Zhang, M. Reinforcement of unsaturated polyester by aluminum and aluminum oxide nanollers. Mate rials Le tte rs, 2004, 58 (3-4), 408-412. Xu, W.B.; Ge, M.L. & He, P. Nonisothermal crystallization kinetics of polypropylene/montmorillonite nanocomposites. J. Polym. Sci . P t B : P olym. Phys., 2002, 40 (5), 408. Haggenmueller, R.; Gommans, H.H.; Rinzler, A.G.; Fischer, J.E. & Winey, K.I. Aligned single-wall carbon nanotubes in composites by melt processing methods. Chem. Phy. Lett. , 2000, 330 (3-4), 219-25. Haggenmueller, R.; Zhou, W.; Fischer, J.E. & Winey, K.I. Mechanical and structural investigation of highly aligned single-walled carbon nanotubes in polymer composites. J. Nanosc i. Nanote chn o., 2003 , 3, 105. Baughman, R.H.; Zakhidov, A.A. & de Heer, W.A. Carbon nanotubesThe route towards applications. Science, 2002, 297 , 787-92. Glatkowski, P.; Mack, P.; Conroy, J.; Piche, J.W. & Winsor, P. Electromagnetic shielding comprising nanotubes. 561
DEF SCI J, VOL. 60, NO. 5, SEPTEMBER 2010
73. 74.
75. 76.
77.
78. 79.
80.
81. 82.
83.
84. 85. 86.
87.
562
US Patent No. 6265466, 2001. Huang, J Kaner, RB, Flash welding of conducting polymer nanofibres. Nat ure Materi als , 2004, 3 (11), 783-86. Linda, S. Schadler. Polymer-based and polymer-filled nanocomposites. In Na no co mp os it e sc ie nc e an d technology, edited by P. M. Ajayan; L. S. Schadler & P. V. Braun. WILEY-VCH Verlag GmbH Co. KGaA, Weinheim, 2003. pp. 77-1 53. Lee, Y.S. & Wagner, N.J. Dynamic properties of shear thickening colloidal suspensions. Rhe ologic a Act a, 2003, 42(3), 199-208. Lee, Y.S.; Wetzel, E.D.; Egres Jr., R.G. & Wagner, N.J. Advanced body armor utilizing shear thickening fluids. In Proceedings of the 23rd Army Science Conference 2002. Orlando, FL, 2-5 December 2002. Lee, Y.S.; Wetzel, E.D. & Wagner, N.J. The Ballistic impact characteristics of Kevlar®Woven fabrics impregnated with a colloidal shear thickening fluid. J. Ma ter. Sci . , 2003, 38 (13), 2825-833. Nguyen, T. & Diaz, A.F. Novel method for the preparation of magnetic nanoparticles in a polypyrrole powder. Adv anced Mater ial s, 1994, 6 (11), 858-60. Bohm, J.; Haubelt, J.; Henzi, P.; Litfin, K. & Hanemann, T. Tuning the Refractive Index of Polymers for Polymer Waveguides Using Nanoscaled Ceramics or Organic Dyes. Adv. Engg. Mater., 2004, 6(1-2), 52-57. Rapoport, L.; Nepomnyashchy, O.; Verdyan, A.; PopowitzBiro, R.; Volovik, R.; Ittah, B. & Tenne, R. Polymer Nan ocomposites with Fuller ene-like Soli d Lubrican t. Adv. Engg. M ater., 2004, 6(1-2), 44-48. Siripurapu, S.; DeSimone, J.M.; Khan, S.A. & Spontak, R.J. Low-temperature, surface-mediated foaming of polymer films. Advanced Materials, 2004, 16 (12), 989-94. Watson, K.A.; Smith Jr., J.G. & Connell, J.W. Space durable polyimide/nanocomposite films for electrostatic charge mitigation. In Science for the Advancement of Materials and Process Engineering Proceedings , 2003, 48 , 1145. Zhang, W.; Zeng, J.; Liu, L. & Fang, Y. A novel property of styrenebutadienestyrene/clay nanocomposites: Radiation resistance. J. Mat er. Chem., 2004, 14, 20913. Jiang, L.; He, S. & Yang, D. Resistance to vacuum ultraviolet irradiation of nano- TiO2 modified carbon/ epoxy composites. J. Mater. Res., 2003, 18(3), 654-58. Gilman, J.W.; Kashiwagi, T. & Lichtenhan, J.D. nanocomposites: a revolutionary new flame retardant approach. SAMPE Journal , 1997, 33 (4), 40-6. Kashiwagi, T.; Grulke, E.; Hilding, J.; Groth, K.; Harris, R.; Butler, K.; Shields, J.; Kharchenko, S. & Douglas, J. Thermal and flammability properties of polypropylene/ carbon nanotube nanocompoaites. Polymer , 2004, 45(12), 4227-239. Gentle, T.E. & Baney, R.H. Silica/silicone nanocomposite films: A new concept in corrosion protection. In Proceeding of Materials Research Society Symposium, 1992, 274, pp. 115-19.
88. Gall, K.; Dunn, M.L.; Liu, Y.; Finch, D.; Lake, M. & Munshi, N.A. Shape memory polymer nano composites. Act a Mate ria lia , 2002, 50 (20), 5115-126. 89. EI-Fatatry, A. Defence applications. In Nanotechnology Aerospace Applications . RTO-EN-AVT-129, 2005, pp. 5-15-6. 90. Ghosh, S.; Sood, A.K. & Kumar, N. Carbon nanotube flow sensors. Science, 2003, 299 (5609), 1042-044. 91. Shankar, S.S.; Rai, A.; Ankamwar, B.; Singh, A.; Ahmad, A. & Sastry, M. Biological synthesis of triangular gold nanoprisms. Nature Ma teri als, 2004, 3 (7), 482-88. 92. Srivastava, A.; Srivastava, O.N.; Talapatra, S.; Vajtai, R. & Ajayan, P.M. Carbon nanotube filters. Nature Materials , 2004, 3(9), 610-14. 93. Sreekumaran Nair, A.; Tom, Renjis T. & Pradeep, T. Detection and extraction of endosulfan by metal nanoparticles. J. Env iro n. Monit. , 2003, 5 , 363-65, 94. Karuppiah, Murugan. & Tata, Narasinga Rao. A process for the preparation of nanosilver and nanosilver-coated ceramic powders. Report No. 2786/DEL/2005, 26 December 2008. 95. Kaliyan, Hembram; Vijay, R.; Srinivasa Rao, Y. & Tata, Nar asi nga Rao . D oped nanoc rys tal lin e ZnO powders for non-linear resistor applications by spray pyrolysis method. J. N anosci . Na notech nol., 2009, 9(7), 4376382. 96. Sundararajan, G. & Tata Narasinga Rao. Commercial Prospects for Nanomaterials in India. J. Indi. Ins t. Sci., 2009, 89 (1), 35-41. 97. Charati, S.G.; Dhara, D.; Elkovitch, M.; Ghosh, S.; Mutha, N.; Raj ago pal an, S. & Shaikh, A.A.: US Pat ent No. 20067026432, 2006. 98. Hidefumi, H. & Toomasu, E. Method for purifying carbon-nanotube. Patent No. JP6228824, 1994. 99. Kong, J.; Franklin, N.R.; Zhou, C.; Chapline, M.G.; Peng, S.; Cho, K. & Dai, H. Nanotube molecular wires as chemical sensors. Science, 2000, 287 , 622-25. 100. Ajayan, P.; Lahiff, E.; Stryjek, P.; Ryu, C.Y. & Curran S. Embedded nanotube array sensor and method of making a nanotube polymer composite. Patent No. WO04053464A1, 2004. 101. Courty, S.; Mine, J.; Tajbakhsh, A.R. & Terentjev, E.M. Nematic ela sto mers with ali gne d car bon nanot ubes: New electromechanical actuators. Europhys. Lett ., 2003, 64(5), 654-660. 102. Ounaies, Z.; Park, C.; Harrison, J.S.; Holloway, N.M. & Draughon, G.K. Sensing/actuating materials made from carbon nanotube polymer composites and methods for making same. US Patent No. 2006084752, 2006. 103. Sharon, Maheshwar, Pradhan, D.; Zaharia, R. & Puri, V. J. A pplication of carbon nanomaterial as a microwave absorber. J. Nanosci . Nanote chnol ., 2005, 5(12), 211720. 104. Bai, X.D.; Zhong, D.Y.; Zhang, G.Y.; Ma, X.C.; Liu, S.; Wang, E.G .; Chen, Y. & Shaw, D.T. Hydrogen stora ge in carbon nitride nanobells. Appl . Phy. Lett ., 2001, 79(10), 1552-554.
KURAHATTI, et al.: DEFENCE APPLICATIONS OF POLYMER NANOCOMPOSITES
105. Nanotechnology aerospace applications. In RTO Lecture Series, EN-AVT-129, May 2005. 106. Hasegawa, N.; Okamoto, H.; Kato, M. & Usuki, A. Preparation and mechanical properties of polypropyleneclay hybrids based on modified polypropylene and organophilic clay. J. Appl. Polym. Sc i., 2000, 78 (11), 1918-922. 107. Lan, T. & Pinnavaia, T.J. Clay-reinforced epoxy
nanocomposites. Chem. Mate r., 1994, 6(12), 2216-219. 108. Savage, S.J. Defence applications of nanocomposite materials. FOI-Swedesh Defence Research Agency, User Report No. FOI-R-1524-SE, December 2004. 109. Koerner, H.; Price, G.; Pearce, N.A.; Alexander, M. & Vaia, R.A. Remotely actuated polymer nanocompositesstress-recovery of carbon-nanotube-filled thermoplastic elastomers. Nat ure Mat erial s , 2004, 3(2), 115-34.
Contributors Mr R.V. Kurahatti obtained his ME
(Production Technology) from Visvesvaraya Technological Univ ersity, Belgaum in 1999. Presently, he is working as Senior Lecturer in Basaveshwar Engineering College, Bagalkot (Karnataka) and pursuing PhD in the Dept of Metallurgical and Materials Engineering, National Institute of Technology Karnataka, Surathkal. Dr A.O. Surendranathan obtained his
PhD from Mangalore University, Karnataka in 1994. Presently, he is working as Professor in National Institute of Technology Karnataka, Surathkal. His research areas are superplasticity, batteries, corrosion, powder metallurgy, electroplating, welding, heat treatment, pol ymers, comp osites and nano technology. Dr S.A. Kori obtained his PhD from
IIT, Kharagpur in 2000. He joined as teaching faculty in Basaveshwar Engineering College Bagalkot in 1987. Presently, he is Registrar (Evaluation) in Visvesvaraya Technological University, Belgaum. He has published 25 research papers in international journals and 60 papers in international and national conference pr oc eedi ng s. He ha s r ecei ve d Uni ve rs it y G rant s C om mi ssio n fellowship of Indo-Hungarian faculty exchange programme in 2005.
Dr Nirbhay Singh obtained his MTech
and PhD from IIT, Kanpur. Presently, he is working as Scientist G (Additional Director) in DMSRDE (DRDO) Kanp ur. His research areas are metallic corrosion and its prevention, fatigue and fracture studies of metallic and non-metallic materials, failure analysis of aircraft components, polymer nanocomposites. He has published 70 papers in national and international jo ur nals /c on fere nces. Dr A.V. Ramesh Kumar obtained his
MSc (Physical Chemistry) from School of Chemistry, Andhra University and PhD (Applied Chemistry) from Kanpur University. He joined DMSRDE, Kanpur as Scientist C and work ed there ti ll May 2009 and currently is posted in Naval Physical and Oce anographic Laboratory (NPOL), Kochi. He has filed 4 patents and published 4 technical reports. Mr Saurabh Srivastava obtained his
BTech (Mechanical Engineering) from Institute of Engineering and Technology, Lucknow. He worked with M/s L&T before jo in in g DR DO as Sc ie nt is t. Cu rr en tl y, he is working as Scientist C in DMSRDE, Kanpur.
563