Antenna Test 3 cmds go together
Transciever Test
Runs Test Prints test results Deletes test report
ZUBS:BTS=bts,TRX=trx; ZUBP:TR:BTS=bts,TRX=trx; ZUBD:TR:BTS=bts,TRX=trx;
Link Link Link
TRX Top layer info for BCF Output BCF network configuration Output BCF and TRX parameters
ZEEI:BCF=bcf; (Also shows Lac ID & CI Cell ID) ZERO:BCF=bcf;
Link Link
ZEEI:BTS=bts; (Also shows Lac ID & CI Cell ID) ZERO:BTS=bts; (ET Must match info in ZEEI cmd)
Link Link
Top layer info for BTS Output BTS network configuration Output BTS and TRX Parameters
Lock / Unlock Trx Lock (FHO Forces Handover) Trx Unlock Block TRX sub time slot Unlock TRX sub time slot
ZERS:BTS=bts,TRX=trx,:L:FHO; ZERS:BTS=bts,TRX=trx:U; ZERS:BTS=bts,TRX=trx,CH=ch:L; ZERS:BTS=bts,TRX=trx,CH=ch:U;
Test 3 cmds go together
Runs Test Prints test results Deletes test report 3 cmds go together
Runs Test Prints test results - Verifies Voice path on TRX Deletes test report
Transciever Test ZUBS:BTS=bts,TRX=trx; ZUBP:TR:BTS=bts,TRX=trx; ZUBD:TR:BTS=bts,TRX=trx;
Link Link Link
Abis Loop Test ZUBK:TEST:BTS=bts,TRX=trx; ZUBP:AL:BTS=bts,TRX=trx; ZUBD:AL:BTS=bts,TRX=trx;
Link Link Link
ZERO:BCF=bcf; ZERO:BTS=bts; ZEQV:BTS=bts:GENA=Y; ZEQV:BTS=bts:GENA=N; ZEQO:BTS=bts:GPRS; BTS MUST BE BLOCKED BEFORE COMMAND WILL EXECUTE
Link Link
GPRS Output BCF and TRX parameters Output BTS and TRX Parameters Enable GPRS for sector Disables GPRS for sector Check a BTS' GPRS parameters Change BTS GPRS parameters Change "dedicated" GPRS capacity for sector Change "default" GPRS capacity for sector
ZEQV:BTS=bts:CDED=xx; ZEQV:BTS=bts:CDEF=xx;
TRXSIG TRXSIG information
ZERO:BTS=bts,TRX=trx;
Link
Interrogate TRX D-channel working state Block working state of TRX LAPD Restore LAPD RESTORES LAPD
ZDTI:NAME=trxsig; ZDTC:NAME=trxsig:BL; ZDTC:NAME=trxsig:WO; ZDTC:trxsig:P,WO;
Link
ZEEL;
Link
ZDSB; ZDSE:trxsig:BSCU,x:0,x:16,xx-xx,xx; ZDSE:
:BCSU,:,:,,;
Link
Parameters Output TRX Radio Timeslots on BSC
ADD TRXSIG will need to be done first Check if TRXSIG already exists
Create TRXSIG link_name index sapi tei rate t1_tsl sub_tsl
> > > > > > >
TRX add to existing BTS
Name of the LapD link Index of the BCSU controlling the link Service access point identifier > 62 for OMUSIG, 0 fro TRXSIG Terminal end point identifier > 1 for OMU link & TRX number for TRXSIG (ie 1,3 & 5) Bit rate of the link > 16 for OMU, 16 for TRX T1 & the time slot used by the link Starting bit of sub timeslot in the T1 frame ZERC:BTS=bts,TRX=trx:GTRX=Y:FREQ=freq,TSC=tsc,PCMTSL=xxx:DNAME=trxsig:SIGN=0,LEVD=-83,FRT=0,CH0=SDCCH;
The information below will need to be gathered first.
BTS# > TRX # > FREQ - ARFN > TSC (Training sequence code) > PCMTSL - PCM and time slot > DNAME > SIGN > LEVD > FRT > CH0 > CH TYPE "each of the eight time slot need to have a type assigned, default in tchf".
BTS TRX Channel must be same TSC as existing TRX in that sector. First of the two ABIS traffic time slots used by the TRX. (example.. T3703) "bcf-37, trx-3" Same as TRXSIG =0 - 83 =0 MBCCHC for first radio in BTS. (combined MBCCH & SDCCH)
>
MBCCHC is used for the first TRX of a BTS.
>
SDCCH may be used for second timelot on first TRX of a BTS.
Link to steps for building a TRX Delete TRX ZERD: Talks to FXC card Remote Session
ZQUS:
Link
BTS Top layer info for BCF Output BCF network configuration Output BCF and TRX Parameters
Top layer info for BTS Output BTS network configuration Output BTS and TRX parameters BTS Identification Parameters
Lock / Unlock Lock Unlock
Barring BTS for Testing Activates Barring Deactivates Barring
Alarms Active alarms on BSC xx=1 - 248 on BSF Cancel alarm History y=year m=month Alarm history back to midnight for all BCF's Alarm history back to midnight For one BCF Output blocked BTS alarms Block BTS alarm Unblock BTS alarm
>
ADD Create BTS CI= BAND= NCC= BCC= MCC= MNC= LAC= HOP= UHOP =
> > > > > > > > >
TRXSIG Shows LapD for TRX Checks TRXSIG Interrogate TRX D-channel Block working state of TRX LAPD Unlock/Restore LAPD Which Dchan have been created & Parameters Interrogates memory blocks for LapD
OMUSIG Status OMUsig
Block OMUsig Restore OMUsig Interrogates memory blocks for LapD
Parameters Power control parameters BTS Identification parameters Misc Parameters Output Handover control parameters Modify Miscelaneous BTS Parameters
> >
LAC ID / Cell ID / RF Chan Display BTS Work Load Output Mobile allocation frequency list Display cell broadcast messages Display Messages
GPRS Output BCF and TRX parameters Output BTS and TRX Parameters Enable GPRS for sector Disables GPRS for sector Check a BTS' GPRS parameters Change BTS GPRS parameters Change "dedicated" GPRS capacity for sector Change "default" GPRS capacity for sector
Adjacent cell info Adjacent cell parameters Adjacent cell data
TESTING Synchronize BCCH for terminating test call Start call status request Start originating test call Start BCCH field strength measurement Start receiver sensitivity measurement Interrupt test Start Transciever test Print single test report Delete test repot Build a BTS
ZEEI:BCF=bcf; (Also shows Lac ID & CI Cell ID) ZERO:BCF=bcf;
Link Link
ZEEI:BTS=bts; ZERO:BTS=bts; (ET Must match info in ZEEI cmd) ZEQO:ALL;
Link Link
ZEQS:BTS=bts:L; ZEQS:BTS=bts:U; ZEQF:BTS=bts,BAR=N; ZEQF:BTS=bts,BAR=Y; ZEOL; ZEOL:bcf; ZEOR:; ZEOH:yyyy-mm-dd,00-00-00:BCF=xx; ZEOH; ZEOH:,:BCF=bcf; ZEOE; ZEOB:; ZEOU:;
Link
Link
ZEQC:BCF=, BTS=,:CI=,BAND=:NCC=, BCC=:MCC=,MNC=, LAC=:HOP=,UHOP=N; Cell Identity must be the same as BTS number used. frequency band of cell…. GSM=900mhz. DCS= 1800 mhz. DSC19=1900 mhz. Network color code BTS color code Mobile country code 310 in the U.S. Mobile Network Code (Use ZEFO command on existing site) Location area code identifies all BCF within the BSS. "Frequency hopping mode" >No No ZERO:BTS=bcf; ZDSB; or ZDSB:NAME=trxsig:; ZDTI:NAME=trxsig; ZDTC:NAME=trxsig:BL; ZDTC:NAME=trxsig:WO; ZDSB:::PCM=et; ZDFD:OMU:054C,record#; ZDTI; shows record # for LapD to use with command
Link Link Link
ZDTI:NAME=omusig;
Link
Link
ZDTI:NAME=omusig:BL; ZDTI:NAME=omusig:WO; ZDFD:OMU:054C,record#; ZEUO:BTS=bts; ZEQO:BTS=bts; ZEQO:BTS=bts:MIS; ZEHO;BTS=bts;
ZDTI; shows record # for LapD to use with command
(LAC CODE AND CI INFO)
Link Link Link Link
ZEQM:BTS=bts:RDIV=Y; (Enables GPRS to a sector.) ZEQM:BTS=bts:RDIV=N; (Disables GPRS for a sector.)
ZECL;
Link
ZEBI;
Link
ZECP;
Link
ZERO:BCF=bcf; ZERO:BTS=bcf; ZEQV:BTS=bts:GENA=Y; ZEQV:BTS=bts:GENA=N; ZEQO:BTS=bts:GPRS; BTS MUST BE BLOCKED BEFORE COMMAND WILL EXECUTE ZEQV:BTS=bts:CDED=xx; ZEQV:BTS=bts:CDEF=xx; ZEAO:BTS=bts; ZEAT; Equipment not installed at site to do this testing ZUBE ZUBF ZUBG ZUBH ZUBJ ZUBN ZUBS ZUBP ZUBD
Link
Link Link
BCF Top layer info for BCF Output BCF network configuration Output transceiver parameters on BCF Active alarms on BSC Status OMUsig BCF Parameters Lists existing software builds for BCF in BSC Lists SW configuration of BCF Interrogates LapD channel info
Top layer info for BTS Output BTS network configuration Output transceiver parameters on BTS
Reset / Lock / Unlock OMU Reset BCF Lock Unlock
OMUSIG (LAPD) Status OMUsig Block OMUsig Restore OMUsig Shows parameters for OMUSIG Interrogates memory blocks for LapD
Create OMUSIG Choosing a BSCU to assign OMUSIG to Link to change OMUSIG or TRXSIG after BCF has already been built
Alarms Active alarms on BSC xx=1 - 248 on BSC Cancel alarm History y=year m=month Alarm history back to Midnight For all BCF's Alarm history back to Midnight For one BCF Output blocked alarms
Parameters Output transceiver parameters on BCF Output maintenance mode parameters BCF Parameters
Interrogates BCF Interrogates all BCF's Interrogates one BCF
LAC ID to BCF
Software Software configuration Software Package contents List existing BCF software packages List BCF software handling system activities
Checks Adjacent Cell Data List
HW database configuration
List HW Databse Configuration of BCF
Link To Steps For Sectorizing A BCF Link To Steps For Rehoming A BCF Service Terminal Abis Monitoring (OMUSIG) TRXSIG Monitoring
Channel Mapping Build A BSF
ZEEI:BCF=bcf; (Also shows Lac ID & CI Cell ID) ZERO:BCF=bcf; ZEOL:bcf; ZDTI:NAME=omusig; ZEFO:bcf; ZEWL; ZEWO:bcf; ZDSB;
Link Link
ZEEI:BTS=bts; ZERO:BTS=bts; (ET Must match info in ZEEI cmd)
Link Link
ZEFR:bcf:OMU; ZEFS:bcf:L; (Drops Calls) ZEFS:bcf:U; ZDTI:NAME=omusig; ZDTI:NAME=omusig:BL; ZDTI:NAME=omusig:WO; ZDSB:NAME=omusig; ZDFD:OMU:054C,record#;
Link
ZDTI; shows record # for LapD to use with command
ZDSE:omusig:BCSU,x:62,1:16; ZEEI::BCSU; (Out of the list, choose the BSCU with the least loading) ter BCF has already been built
Link
ZEOL; ZEOL:bcf; ZEOR:xx ZEOH:yyyy-mm-dd,00-00-00:BCF=bcf; ZEOH; ZEOH:,:BCF=bcf; ZEOE;
Link
ZERO:BCF=bcf;
Link
ZEMO:bcf; (xx=BCF)
Link
ZEFO:bcf; (xx=BCF)
Link
ZDTI;
Link
ZDTI:NAME=omusig;
Link
ZEQO:LAC=lac_id,CI=cell_id;
ZEWO:bcf; ZEWP:ID=xx_xx_x; (ID=Build ID obtained with ZEWL CMD) ZEWL; ZEWI:bcf; (xx=BCF)
Link Link Link Link
ZEAT;
Link
ZEVO:bcf:;
Link
ectorizing A BCF
ehoming A BCF ABM_BXSX TGM_BXSX RPHASGSX
( ABIS Telecom Monitoring ) ( BCF Phase Monitoring)
A bis ABIS FUNCTION Signaling between BSC & BTS 16 Kbps is used for operational configurations Signaling protocol LapD for BSC to BCF communication OMUSIG for 2nd generation equipment BCFSIG for 3rd generation equipment Signaling protocol LapD for BSC to TRX for TRXSIG
Top Layer Info For ABIS Output transceiver parameters on BCF Output transceiver parameters on BTS
ZERO:BCF=bcf; ZERO:BTS=bts;
Interrogate TRX LAPD Info - TRXSIG
ZDTI:trxsig;
Status OMUsig
ZDTI:NAME=omusig;
Lap D BTS OMUSIG
Block Restore
TRXSIG
Block Restore
BC=BCF ZDTC:omusig:BL; ZDTC:omusig:WO; T=TRX ZDTC:trxsig:BL; ZDTC:trxsig:WO;
Add Building A-bis interface
Parameters ABIS route info and working state ZNET;
Alarms
Service Terminal Abis Monitoring (OMUSIG) TRXSIG Monitoring
ABM_BXSX TGM_BXSX
( ABIS O & M Monitor) ( ABIS Telecom Monitor )
Link Link
Link
Examples bcf=100 input bc100 bcf=99 input bc099 Examples trx=1,bcf=99 input t9901 trx=1,bcf=100 input t1001
O & M Monitor) S Telecom Monitor )
Link
T1 Top Layer Info for T1 Output BCF network configuration LAPD status Interrogate D-CHANNEL STATE Output statistical disturbances on circuit
Interrogate PCM service state
LOCK / UNLOCK LapD Block LAPD Restore LAPD
T1 Test Output statistical disturbances on circuit
Interrogate PCM service state Interrogate D-CHANNEL STATE Interrogate D-CHANNEL STATE
RESET ET TIMERS
Cross reference ET to get BCF info
OMUSIG & Parameters Cross reference ET to get BCF info
Loop FXC Card
ZEEI:BCF=bcf; This will gives LAPD information to run the below command ZDTI:NAME=omusig; Shows working state and time slot information. (OMUSIG) ZDTI:NAME=trxsig; ZYMO:ET,et; Error Free Seconds (EFS0 should equal 100%) Remote / Local ZYEF:ET,et; (et=PCM #) ZDTC:NAME=omusig:BL; ZDTC:NAME=omusig:WO;
ZEEI:BCF=bcf; This will give ET information to run the below command ZYMO:ET,et; Error Free Seconds (EFS0 should equal 100%) Remote / Local ZYEF:ET,et; (et=PCM #) ZDTI:NAME=trxsig; ZDTI:NAME=omusig; ZUSC:ET,et:TE,FCD; (Forces ET in test state) should see an "execution started" reply. ZUSC:ET,et:SE; Take ET to (separate/out of use) state. ZUSC:ET,et:SE; SAME COMMAND AGAIN takes ET to "Separate/Out of use state". To get ET back in service run commands in order as below ZUSC:ET,et:SE; ZUSC:ET,et:TE; ZUSC:ET,et:WO; Now run the ZYMO:ET,et; and the ET timers should be reset (100%)with no errors if the span is clean. ZDSB:::PCM=et; (USE the ET number for PCM) This will tell you which site this ET belongs to. ZDSB:NAME=omusig; ZDSB:::PCM=et; (USE the ET number for PCM) This will tell you which site this ET belongs to.
Link Link
Link Link
Link
Link
BSC TOP LEVEL INFORMATION ON BSC Shows C-NUM and name of BSC All BSC related alarms A-Interface / A-bis signaling Interface Signalling Link Status - Should be AV-EX Operating states of all Units in BSC Status all BCF's in BSC Local IP to BSC
ZQNI; ZAHO; ZNET; ZNEL; ZUSI:ALL; ZEEI; ZQRI:OMU;
SS7 Through Connections
ZWGO;
Link Link
Block Units in BSC OMU (Operation and maintenance unit)
>
Interrogate state Change state Test unit Restart unit
MCMU (Marker and Cell
Central supervision
ZUSI:OMU; ZUSC:OMU: ZUDU:OMU: ZUSU:OMU; Management Unit)
>
Interrogate state Change state Test unit Restart unit Shows BCF's connected to MCMU Shows BTS's connected to MCMU
BCSU (Base station controller signaling unit)
Link
Conn & Rls all connections
ZUSI:MCMU; Link ZUSC:MCMU: ZUDU:MCMU: ZUSU:MCMU; ZDFB:MCMU,0:639000C; Link ZDFB:MCMU,0:6390004; Link >
Interrogate state Change state Test unit Restart unit BSCU Alarm history to midnight Working state of all BSC cards. Clears flags under ZUSI; Shows created trxs, links & tchs under BCSU's
CLSU (Clock & Sync Unit)
Link
>
Interrogate state Change state Test unit Restart unit
1 BCSU handles 16 TRX's
ZUSI:BCSU,x; ZUSC:BCSU,x: ZUDU:BCSU,x; ZUSU:BCSU,x; ZAHP:BCSU,x; ZUSI; ZUST:BCSU,x ZEEI::BCSU;
Link
Link Link
Generates clock signals
ZUSI:CLS,x; ZUSC:CLS,x: ZUDU:CLS,x; ZUSU:CLS,x;
Link
OMUSIG (LAPD) Interrogate D-Channel working state Status OMUsig Block OMUsig Changes to working state Parameters for TRXSIG / OMUSIG
ZDTI; ZDTI:NAME=omusig; Link ZDTI:NAME=omusig:BL; ZDTI:NAME=omusig:WO; ZDSB:NAME=omusig;
LAP D TC Output transcoder PCM info / SS7 Connection ZWGO;
Link
Counters Inquire and output counters Output counters Show description of the counters Reset the counters
ZTVI ZTVO ZTVS ZTVR
Parameters Outputs General BSC Parameters Output BSC parameters Status of optional features of BSC BSC alarm parameters Output timer parameters A-Interface signaling Shows Date & Time Gateway IP Local IP to BSC Outputs BSSAP & SCCP INFO SS7 Through connections Output TRX Radio Timeslots on BSC Interrogate Services Interrogate circuits/circuit groups
ZEEM: ZEEO; ZWOO; ZEOO; ZEGO; ZNET; ZDCD; ZQRL; ZQRI:OMU; ZNHI; ZWGO; ZEEL; ZNPI; ZRCI:GSW;
Link
Link
Alarms Lists alarms currently on BTS List alarm history All BSC related alarms Alarms from aall cp units (OMU, MCMU & BCSU's) Alarm history for BSC Clears alarms x=(1-min, 2-maj, 3-crit) Block paticular BTS alarms in Bsc Lists blocked BTS alarms Checks blocked cell sites Output blocked BSC alarms Block BSC alarm Unblock BSC alarm BSC alarm parameters
ZEOL; ZEOH:,:BCF=bcf; ZAHO; ZAHO:COMP; ZAHP:::yyyy-mm-dd; ZACA; ZEOL::CLS=ALx; ZEOB:xxxx; ZEOE; ZEEL:BL; ZABO; ZABB:; ZABU:: ZEOO;
Link
BCF Status all BCF's in BSC Status one paticular BCF Show all blocked time slots in BSC Shows busy timeslots "Calls up"
ZEEI; ZEEI:BCF=bcf; ZEEL:BL; ZEEL;
Service Terminal Entering Service Terminal Mass Memory Handling Package handling ABIS O & M Monitoring ABIS Telecom Monitoring
Change Delivery
Building a BSC Service Terminal
ZDDS; MASHANGX.IMG PACKETGX.IMG ABM_BXSX TGM_BXSX
Outputs BSSAP & SCCP INFO - MSC Connection ZNHI; Shows Working states of I/O ZISI:,OMU:ALL; Looks at plug in units for the entire BSC ZWTI:P; Top Level GB Conection Info Output The Network Service Virtual Connection Data ZFWO:BCSU=0&&8; Interrogating Frame Relay Bearer Channel Data (Tunnel to SGSN)ZFUI; Show info on ET's in Group switch (ERATES=Gb, SC7PRB=tcsm)ZWIP:GSW:et;
Unit Funtions MB (Message Bus)
>
Interrogate state Change state Test unit Restart unit
ET
(Exchange Terminal)
Physical connection between CP's
ZUSI:MB,x; ZUSC:MB,x: ZUDU:MB,x; ZUSU:MB,x; >
ZUSI:ET,et; ZUSC:ET,et: ZUDU:ET,et; ZUSU:ET,et; ZYMO:ET,et; ZWUC:
CLAB (Clock & Alarm Buffer)
Synchronization for BSC
Interrogate state Change state Test unit Restart unit
SBUS
Link
T1 Termination
Interrogate state Change state Test unit Restart unit (Restarts two ET ports) Output ET statistical counters Defines ET >
>
Link
ZUSI:CLAB,x; ZUSC:CLAB,x: ZUDU:CLAB,x; ZUSU:CLAB,x;
Link
ZUSI:SBUS,x; ZUSC:SBUS,x: ZUDU:SBUS,x; ZUSU:SBUS,x;
Link
ZDTI; ZDSB; ZERO:BTS=bts,TRX=trx; ZDTI:NAME=trxsig; ZDTC:NAME=trxsig:BL;
Link Link Link Link
(Supervision Buffer)
Interrogate state Change state Test unit Restart unit
TRXSIG (LapD BTS) Interrogate D-Channel working state Parameters for TRXSIG / OMUSIG TRXSIG information Interrogate TRX D-channel Block working state of TRX LAPD
Restore LAPD Which Dchan have been created & Parameters
ZDTC:NAME=trxsig:WO; ZDSB:::PCM=et;
Link
BSC LINKS Outputs links from BSC to SGSN CLNS Object data Links, LAN and x.25 CLNS SS7 THROUGH CONNECTIONS Interrogate BSC D-channel Link set data Interrogate Network item states Interrogate signalling link set data
ZFWO:BCSU=0&&8; ZQEI; ZQLI; ZWGO; ZDSI; ZNET; ZNSI:link_set_name;
Link Link Link
ZEHO:BTS=bts;
Link
ZEWO; ZEWP: ZEWL; ZEWI; ZWQO:CR; ZWQO:RUN;
Link
Handovers output handover info
Software Software configuration Software Package contents List existing BCF software packages List BCF software handling system activities Output created SW packages in BSC Output SW packages running in CP units
Signaling Links Link Status - Should be AV-EX Interrogate signaling link event logs Empty signaling link event logs Interrogate signaling route states Interrogate signaling route set states Interrogate signaling link set states Interrogate network item states Interrogate signaling point load sharing Interrogate subsystem data of signaling points Interrogate Broadcast status of SCCP signaling points Interrogate SCCP state Interrogate SCCP data of signaling points Interrogate SCCP subsystem data state Interrogate SCCP subsystem distribution data Interrogate signaling point data Interrogate STP access Interrogate prohibited STP messages TESTING
ZNEL; ZOLL ZOLE ZNVI ZNER ZNES ZNET ZNEO ZNFJ ZOBI ZNGI ZNFI ZNHI ZNHJ ZNRI ZNRS ZNEP
Link Link
Test signaling data link Interrogate signaling data link test result
ZNLT ZNLO
Routing Interrogate route Interrogate status of SCCP signalling points Interrogate local status of SCCP subsystems
ZRRI ZOBI; ZOBL;
Display cell broadcast messages ZECP;
I/O Shows Working states of I/O
ZISI:,OMU:all;
UNIT FUNCTION
>
OMU FUNCTION Local user Interface NMS Connection Fault Collection Recovery Activation Diagnostic Activation No Redundancy MB FUNTION Physical connection between the CP Units Controlled by MB interfaces on CP Units
MCMU FUNCTION Controls & Supervises Group Switch Connects & releases all connections Contains all system config data Contains master copies of distributed files
ET FUNCTION Electrical sync & adaptation of PCM B8ZS Coding & Decoding Insert alarm bits in outgoing direction Produces the PCM frame structure No redundancy BCSU FUNCTION Handles 16 TRX's Handles SS7 signaling between BSC & MSC Handles LapD signaling between BSC & BTS's
CLAB FUNCTION Distributes basic timing signals Alarm Buffer CLSU FUNCTION Generates clock signals for MSC & BSC
GPRS Top Level Info on GPRS Output BCF and TRX parameters Output BTS and TRX Parameters Network Service Virtual Connection Parameters - Shows NSEI's Interrogating Frame Relay Bearer Channel Data (Tunnel to SGSN) Output Routing Areas Enable GPRS for sector Disables GPRS for sector Check a BTS' GPRS parameters Change BTS GPRS parameters Change "dedicated" GPRS capacity for sector Change "default" GPRS capacity for sector
Gb links Towards SGSN Output The Network Service Virtual Connection Data Interrogating Frame Relay Bearer Channel Data (Tunnel to SGSN) Creates Tunnel to SGSN Lock Unlock Show info on ET's in Group switch (ERATES=Gb, SC7PRB=transcoder)
Parameters Interrogate Local Bearer Channel Signaling Parameters
Barring / Unbarring GPRS Checks to see if Barring is enabled or disabled Enable Barring on BTS Disable Barring on BTS
Service Terminal
ZERO:BCF=bcf; ZERO:BTS=bts; ZWFO:BCSU=0&&-8; ZFUI; ZEBP; ZEQV:BTS=bts:GENA=Y; ZEQV:BTS=bts:GENA=N; ZEQO:BTS=bts:GPRS; BTS MUST BE BLOCKED BEFORE COMMAND WILL EXECUTE ZEQV:BTS=bts:CDED=xx; ZEQV:BTS=bts:CDEF=xx;
ZFWO:BCSU=0&&8; ZFUI; ZFUC: ZFWS:NSVCI=(name_network_service_id):L; ZFWS:NSVCI=(name_network_service_id):U;
Link
Link Link
ZWIP:GSW; ZFNO;
ZEQO:BTS=bts:CEL; ZEQF:BTS=bts,GBAR=y; ZEQF:BTS=bts,GBAR=N; ZDDS:
Link
A ter FUNCTION Signaling between TCSM & BSC Signaling protocol CCS7 between the MSC & BSC Protocol LapD TCSM - BSC for TCSM alarm reporting and control
Parameters A-Interface signaling Interface Traffic Channel Circuit Group Name
Change Traffic Channel State Changes from working to blocked et-pcm xyzChanges from Blocked to NOT-IN-USE
LAP D TC Output transcoder PCM info
> > > >
ZNET; ZRCI:GSW; ?
Link
ZCEC:ETPCM=et-pcm,CRCT=x-y&&-z:BL; BSC ET connected to MSC (ie. 32, 40, 48, 56) TC A Interface connection, 1 through 4 for full rate The lowest number timeslot in that circuit Highest numbered timeslot in that circuit ZCEC:ETPCM=et-pcm,CRCT=x-y&&-z:NU;
ZWGO;
Link
TCSM TCSM Funtion Compresses 64 kbps channels to 16 kbps channels towards the BSC Uncompresses 16 kbps channels to 64 kbps channels towards the MSC Speech activity detection Framing and sync of the vocoder block
Top Level Info SS7 Through Connections Looks at plug in unit for TCSM's Checks working state of TCSM unit Checks LapD for TCSM - Internal LapD between TCSM & OMU Interrogate Internal & external LapD connections
Locking / Unlocking Transcoder
Logging into TCSM from BSC xx=number of TCSM, 32,40,48,56,64,72 Closes session to TCSM
Parameters Output transcoder PCM info - SS7 Through Connections Interrogate Internal & external LapD connections Configuration of TCSM plug-in-units
Alarms TCSM alarm printout
Synchronization Sync output for TCSM to MSC direction
Restart Restart ET plug in unit Restart TCSM unit
Diagnostics Set TCSM to test state To start diagnostics Display diagnostic results Set TCSM back to working state
Echo Cancellation
Output Echo cancellation in each timeslot Set Echo cancellation to all timeslots on EFR codec Set Eecho cancellation to all timeslots on FR codec Building Transcoders in BSC Layout of cabinet and link
ZDDT:TCSM,xx; User ID: EXPERT Password: SYSTEM Now you are in local user interface in transcoder. Commands are only 3 letters long and if you don't know, what the command is completely, after second letter type ? and third letter. e.g. For alarms in TCSM you use command ZAI If you didn't know third letter I, you could have typed ?I and you get instructions, how to complete the command. Here are some useful commands and short description: ZAI ZLS *** should be something as follows if pcm's connected and working*** **INPUT ***PCM-1 ***PCM-2 ***PCM-3 ***PCM-4 ***PCM-5 ***PCM-6 ***PCM-7 ***EXT ZGT ZUP:ET,x ZUU Diagnostics for the TCSM2A unit ZUC:TE ZCC:TOTAL To start diagnostics ZCO ZUC:WO REMEMBER TO CLOSE YOUR SESSION TO TCSM BY, ZX-COMMAND EVERY TIME YOU LOG OUT !!!!
wards the BSC towards the MSC
ZWGO; ZWTI:P:TCSM,tcsm_#; ZUSI:TCSM,xx; Checks working state of TCSM unit ZDTF:TCSM,tcsm:OMU; ( From Main Level) ZDFS:TCSM:OMU; ZUSC:TCSM,index:TE,FCD;
TE-EX
ZUSC:TCSM,index:SE
(Separated OUT OF USE SE-OU)
ZUSC:TCSM,index:SE
(Separated NO HARDWARE SE-NH)
ZDDT:TCSM,tcsm_#; ZX Username:EXPERT Password: SYSTEM
ZWGO; ( From main level command) ZDFS:TCSM:OMU; ZGT; ZAI;
ZLS;
ZUP:ET,et; ZUU
ZUC:TE ZCC:TOTAL ZCO ZUC:WO
Link
ZRC:1:10 ZRU:ALL:EFR=ON; ZRU:ALL:FR=ON;
(xx=number of TCSM, 32, 40, 48, 56, 63 or 72)
hat the command is completely,
you get instructions, how to complete the command.
TCSM alarm print out Synchronization output for TCSM to MSC direction.
STATE
USED INPUT PRIORITY
USED CONNECTED CONNECTED DISCONNECTED DISCONNECTED DISCONNECTED DISCONNECTED DISCONNECTED
* 10
Shows the configuration of TCSM plug-in units. Restart ET plug-in unit. Restart TCSM unit
Set TCSM to test state Display diagnostics results Set TCSM back to working state ZX-COMMAND EVERY TIME YOU LOG OUT !!!!
7 6 5 4 3
(x= unit number, 0, 1 or 2
USED INPUT PRIORITY***
9 8
(x= unit number, 0, 1 or 2)
A Interface FUNCTION Between MSC & TC Signaling protocol CCS7 between MSC & BSC TDMA frame for sending signals intended for various users on the same radio frequency in different time slots
Top Level Info on A Interface Status Checks status of A-Interface Trunks towards MSC Checks LapD towards Transcoder > towards OMU
Blocks / Unblocks Trunks Blocks A-Interface trunks towards MSC Unblocks A-Interface trunks towards MSC
Parameters A-Interface signaling Interface Outputs BSSAP & SCCP INFO Building the A-Interface
ZCEL:NCGR=name_circuit_group; ZRCI:SEA=1:TYPE=CCS:PRINT=5; ZDTF:TCSM,tcsm:;
ZCEC:ETPCM=et,CRCT=pcm_ckt-xx&&-yy:BL; ZCEC:ETPCM=et,CRCT=pcm_ckt-xx&&-yy:WO;
ZNET; ZNHI;
Link
COMMAND LIST ZA
ALARM SYSTEM ADMINISTRATION
ZA
B
ZA
C
ZA
E
ZA
H
ZA
L
ZA
O
ZA
P
ZA
R
ZA
T
BLOCKED ALARMS HANDLING COMMANDS B BLOCK ALARM U UNBLOCK ALARMS O OUTPUT BLOCKED ALARMS ALARM CANCELLING COMMANDS C CANCEL ACCORDING TO CONSECUTIVE NUMBER A CANCEL ACCORDING TO ALARM NUMBER ERROR RATIO COUNTER HANDLING COMMANDS M MODIFY ERROR RATIO COUNTER BASE VALUE O OUTPUT ERROR RATIO COUNTER VALUES ALARM HISTORY HANDLING COMMANDS O PRINT ALARMS CURRENTLY ON P PRINT ALARM HISTORY LAMP PANEL HANDLING COMMANDS D DISPLAY STATE OF ALARM OUTPUTS O DISPLAY UPDATING OF ALARM OUTPUTS FROM LOCAL SYSTEM L DISPLAY UPDATING OF ALARM OUTPUTS INTO LOCAL SYSTEM U SET UPDATING OF ALARM OUTPUTS S SET STATE OF ALARM OUTPUTS ALARM OPERATING INSTRUCTION HANDLING COMMANDS A ADD OPERATING INSTRUCTIONS C CHANGE OPERATING INSTRUCTIONS D DELETE OPERATING INSTRUCTIONS L LIST OPERATING INSTRUCTIONS ALARM PARAMETERS HANDLING COMMANDS M MODIFY ALARM PARAMETERS O OUTPUT ALARM PARAMETERS ALARM PARAMETERS HANDLING COMMANDS A ADD SUPPORTING/PREVENTING RULE D DELETE SUPPORTING/PREVENTING RULE M MODIFY SUPPORTING RULE O OUTPUT SUPPORTING/PREVENTING RULES R RESTORE SUPPORTING/PREVENTING RULE ALARM PRINTING HANDLING COMMANDS B BLOCK ALARM CLASS PRINTING U UNBLOCK ALARM CLASS PRINTING O OUTPUT PRINTING STATES S SET ALARM PRINTING TIMES D DISPLAY ALARM PRINTING TIMES C CHANGE ALARM PRINTING PARAMETERS L OUTPUT ALARM PRINTING PARAMETERS
ZC
ROUTING STATE ADMINISTRATION
ZC
E
ZC
I
CIRCUIT STATE HANDLING COMMANDS C CHANGE EXTERNAL CIRCUIT STATE P CLEAR PHONE CALL T CALL CONNECTION INFORMATION L LIST EXTERNAL CIRCUIT STATE INTERNAL ROUTING STATE COMMANDS
ZC
R
M MODIFY INTERNAL CIRCUIT OR CIRCUIT GROUP STATE I INTERROGATE INTERNAL CIRCUIT OR CIRCUIT GROUP STATE C MODIFY INTERNAL ROUTE STATE L INTERROGATE INTERNAL ROUTE STATE CIRCUIT GROUP AND ROUTE STATE COMMANDS M MODIFY EXTERNAL CIRCUIT GROUP STATE I INTERROGATE EXTERNAL CIRCUIT GROUP STATE C MODIFY EXTERNAL ROUTE STATE L INTERROGATE EXTERNAL ROUTE STATE
ZD
SYSTEM SUPPORT AND COMMUNICATION
ZD
B
ZD
C
ZD
D
ZD
E
DATABASE HANDLING COMMANDS F LIST DATABASE FILES B BUILD DIRECTORY E DISPLAY DATABASE FILL RATIO L LIST DATABASES C COPY DATABASE TO DISK P PREVENT UPDATING OF DATABASE IN MEMORY OR TO DISK Q MAKE QUERIES TO DATABASE R RESUME UPDATING OF DATABASE IN MEMORY OR TO DISK S DISPLAY DATABASE STATE T PREVENT OR RESUME DATABASE REMOTE COPY UPDATING M COPY DATABASE FROM DISK TO UNIT OR REFRESH SUBDATABASE O SAVE DATABASE LOG TO DISK X EMPTY DATABASE DISK UPDATING LOG Y SET DATABASE CONSISTENCY D DISPLAY DISK UPDATING SYSTEM STATE W COPY DATABASE FROM DISK TO DISK V CHECK INTEGRITY CLOCK HANDLING COMMANDS D DISPLAY DATE, TIME AND TIME ZONE C CHECK DATE AND TIME S SET DATE, TIME AND SUMMER TIME A ADJUST TIME T CHANGE TO STANDARD/SUMMER TIME E SET TIMEZONE REMOTE DEBUGGER SESSION COMMANDS S START REMOTE SESSION E EXECUTE DEBUGGER COMMAND T START REMOTE PREPROCESSOR SESSION X EXECUTE PREPROCESSOR DEBUGGER COMMAND FILE CONVERSION HANDLING COMMANDS C CREATE MEMORY FILE ON DISK OR MEMORY E EXECUTE PROGRAM M COPY MEMORY FILE ON DISK OR MEMORY S UPDATE MEMORY FILE CHECKSUMS AND BITMAP ON DISK I INTERROGATE FILE ATTRIBUTES ON DISK U CHECK FILE SYSTEM INTEGRITY ON DISK V COMPARE TWO FILES SYSTEMS ON DISK P DISPLAY FILE DIMENSIONING PARAMETERS Y INTERROGATE/CHANGE ENVIRONMENT SETTINGS F MODIFY MEMORY FILE HEADER ON DISK
ZD
F
ZD
M
ZD
O
ZD
P
ZD
R
ZD
S
R DISPLAY REPORT FILE OF CONVERSIONS X DISPLAY PROGRESS OF CONVERSIONS MEMORY FILE HANDLING COMMANDS D DISPLAY FILE OR RECORDS S SUBSTITUTE RECORDS OR SUBRECORDS R MODIFY RESERVATION STATES OF RECORDS B LIST RESERVATION STATES OF RECORDS L LIST FILE INFORMATION C COPY FILE OR FILES TO DISK M COPY FILE OR FILES TO MEMORY F COMPARE FILES INTERROGATION OF LAPD AND SBUS STATISTICS METERS COMMANDS F INTERROGATE TRANSMITTED AND RECEIVED FRAMES AND OCTETS I INTERROGATE MISCELLANEOUS STATISTICAL COUNTERS Q INTERROGATE Q.921 ERROR COUNTERS N INTERROGATE OCCASIONAL VALUES OF LINK SET METERS T INTERROGATE OCCASIONAL VALUES OF TERMINAL METERS U INTERROGATE OCCASIONAL VALUES OF FUNCTIONAL UNIT METERS L INTERROGATE LAPD EVENT LOGS E EMPTY LAPD EVENT LOGS V INTERROGATE SBUS COUNTERS OPERATING SYSTEM SUPERVISION AND STATISTICS HANDLING COMMANDS M MODIFY SUPERVISION PARAMETERS P DISPLAY PERMANENT SUPERVISION PARAMETERS T DISPLAY CURRENT SUPERVISION PARAMETERS OF UNIT C MODIFY OPERATING SYSTEM ERROR COUNTER SUPERVISION PARAMETERS E DISPLAY OPERATING SYSTEM ERROR COUNTER SUPERVISION PARAMETERS I INTERROGATE SUPERVISION RESULT H CREATE PROCESSOR TIME USAGE MEASUREMENT R CREATE MEMORY USAGE MEASUREMENT F CREATE FAMILY RESOURCE USAGE MEASUREMENT D DELETE MEASUREMENT G CHANGE STATE OF MEASUREMENT V DISPLAY DEFINED MEASUREMENTS W CREATE PASSIVE WARMING MEASUREMENT O INTERROGATE PASSIVE WARMING STATUS PREPROCESSOR MEMORY HANDLING COMMANDS D DISPLAY MEMORY OF PREPROCESSOR S SUBSTITUTE MEMORY OF PREPROCESSOR F FILL MEMORY WITH GIVEN DATA I INPUT DATA FROM PORT Y DISPLAY BID / PID OF CHORUS-TYPE PREPROCESSOR P DISPLAY CID / PID OF PECTUS-TYPE PREPROCESSOR X DISPLAY CID / PID / MID OF PREPROCESSOR SYNCHRONIZATION UNIT HANDLING COMMANDS M SET OPERATING MODE C CREATE SYNCHRONIZATION INPUTS D DELETE SYNCHRONIZATION INPUTS I INTERROGATE SYNCHRONIZATION UNITS S SELECT SPECIAL FUNCTIONS O SELECT OSCILLATOR HANDLING FUNCTIONS PRIMARY RATE ACCESS D-CHANNEL DATA HANDLING COMMANDS
ZD
T
ZD
U
ZD
V
C CREATE D-CHANNEL LINK SET D DELETE D-CHANNEL LINK SET I INTERROGATE D-CHANNEL LINK SET DATA E CREATE BASE STATION CONTROLLER D-CHANNEL L CREATE BSC LOGICAL UNIT D-CHANNEL B INTERROGATE BASE STATION CONTROLLER D-CHANNEL DATA F INTERROGATE D-CHANNEL DATA OF FUNCTIONAL UNIT PRIMARY RATE ACCESS D-CHANNEL STATE MANAGEMENT COMMANDS C MODIFY D-CHANNEL WORKING STATE I INTERROGATE D-CHANNEL WORKING STATE T MODIFY D-CHANNEL WORKING STATE OF FUNCTIONAL UNIT F INTERROGATE D-CHANNEL WORKING STATE OF FUNCTIONAL UNIT DISK UPDATE HANDLING COMMANDS P PREVENT FILE UPDATES TO DISK R RESUME FILE UPDATES TO DISK D DISPLAY DISK UPDATE STATE Q DISPLAY DISK UPDATE QUEUE STATE DISK LOG HANDLER PROGRAM COMMANDS C CREATE NEW SUBLOG FILE E CLOSE SUBLOG FILE R RESIZE LOGFILE M MODIFY LOG FILTERING SETTINGS D DELETE SUBLOG FILE F CLEAR SUBLOG FILE I INTERROGATE LOG FILTERING SETTINGS G DISPLAY LOG DIRECTORY L DISPLAY LOG DATA P DISPLAY LOG SETTINGS T DISPLAY LOG STATISTICS
ZE
CELLULAR RADIO NETWORK ADMINISTRATION
ZE
A
ZE
B
ZE
C
ADJACENT CELL HANDLING IN BSC COMMANDS C CREATE ADJACENT CELL PARAMETERS D DELETE ADJACENT CELL PARAMETERS M MODIFY ADJACENT CELL PARAMETERS X MODIFY C/I HANDOVER PARAMETERS O OUTPUT ADJACENT CELL PARAMETERS T CHECK ADJACENT CELL DATA BCCH AND MOBILE ALLOCATION FREQUENCY LIST AND RA HANDLING COMMANDS C CREATE BCCH FREQUENCY LIST D DELETE BCCH FREQUENCY LIST M MODIFY BCCH FREQUENCY LIST O OUTPUT BCCH FREQUENCY LIST(S) E CREATE MOBILE ALLOCATION FREQUENCY LIST R DELETE MOBILE ALLOCATION FREQUENCY LIST T MODIFY MOBILE ALLOCATION FREQUENCY LIST I OUTPUT MOBILE ALLOCATION FREQUENCY LIST(S) F CREATE ROUTING AREA G DELETE ROUTING AREA H MODIFY ROUTING AREA P OUTPUT ROUTING AREA(S) SMS CELL BROADCAST HANDLING COMMANDS
ZE
E
ZE
F
ZE
G
ZE
H
ZE
M
ZE
O
P DISPLAY MESSAGE(S) L DISPLAY BTS WORK LOAD BASE STATION CONTROLLER HANDLING COMMANDS M MODIFY GENERAL BASE STATION CONTROLLER PARAMETERS N MODIFY RADIO NETWORK SUPERVISION PARAMETERS Q MODIFY MISCELLANEOUS PARAMETERS U MODIFY DYNAMIC HOTSPOT PARAMETERS T MODIFY PRIORITY LEVEL TO SUBSCRIBER TYPE RELATION R PREPARE DATABASE FOR DOWNLOADING OF BACKGROUND DATA G CONTROL ACTIVATION OF BACKGROUND DATA O OUTPUT BASE STATION CONTROLLER PARAMETERS I OUTPUT RADIO NETWORK CONFIGURATION L OUTPUT TRX RADIO TIME SLOTS P OUTPUT BACKGROUND DATA ACTIVATION STATES BASE CONTROL FUNCTION HANDLING COMMANDS C CREATE BASE CONTROL FUNCTION D DELETE BASE CONTROL FUNCTION M MODIFY BASE CONTROL FUNCTION PARAMETERS O OUTPUT BASE CONTROL FUNCTION PARAMETERS S CHANGE BASE CONTROL FUNCTION ADMINISTRATIVE STATE T SET BASE CONTROL FUNCTION OUTPUTS X SET BASE CONTROL FUNCTION EXTERNAL INPUT PARAMETERS R RESET BASE CONTROL FUNCTION E MODIFY EXTERNAL INPUT AND OUTPUT TEXT P OUTPUT EXTERNAL INPUT AND OUTPUT TEXTS GSM TIMER AND BSC PARAMETERS HANDLING COMMANDS O OUTPUT TIMERS/PARAMETERS T MODIFY TIMER P MODIFY PARAMETERS HANDOVER CONTROL PARAMETERS HANDLING COMMANDS C CREATE HANDOVER CONTROL PARAMETERS G MODIFY GENERAL PARAMETERS A MODIFY AVERAGING PARAMETERS S MODIFY SIGNAL STRENGTH THRESHOLD PARAMETERS Q MODIFY SIGNAL QUALITY THRESHOLD PARAMETERS I MODIFY SIGNAL INTERFERENCE THRESHOLD PARAMETERS D MODIFY SIGNAL INTERFERENCE THRESHOLD PARAMETERS N MODIFY PARAMETERS RELATED TO ADJACENT CEL X MODIFY C/I HANDOVER PARAMETERS Y MODIFY INTELLIGENT UNDERLAY-OVERLAY PARAMETERS P MODIFY MS SPEED PARAMETERS O OUTPUT HANDOVER CONTROL PARAMETERS BASE CONTROL FUNCTION MAINTENANCE MODE HANDLING COMMANDS B BLOCK BASE CONTROL FUNCTION ALARM HANDLING U UNBLOCK BASE CONTROL FUNCTION ALARM HANDLING E LIST BASE CONTROL FUNCTIONS ON MAINTENANCE MODE M MODIFY MAINTENANCE MODE PARAMETERS O OUTPUT MAINTENANCE MODE PARAMETERS BASE TRANSCEIVER STATION ALARMS HANDLING COMMANDS B BLOCK ALARM U UNBLOCK ALARM E LIST BLOCKED ALARMS
ZE
Q
ZE
R
ZE
S
ZE
T
ZE
U
ZE
V
C CHANGE ALARM CLASS M MODIFY ALARM PARAMETERS O OUTPUT ALARM PARAMETERS R CANCEL ALARM H LIST ALARM HISTORY L LIST ALARMS CURRENTLY ON BASE TRANSCEIVER STATION HANDLING IN BSC COMMANDS C CREATE BTS D DELETE BTS A MODIFY MOBILE ALLOCATION FREQUENCY LIST USAGE PARAMETERS B MODIFY BCCH FREQUENCY LIST USAGE PARAMETERS E MODIFY BTS IDENTIFICATION PARAMETERS F MODIFY CELL ACCESS PARAMETERS G MODIFY RADIO LINK CONTROL DL PARAMETERS H MODIFY QUEUEING PARAMETERS J MODIFY CCH CONFIGURATION PARAMETERS K MODIFY INTERFERENCE AVERAGING PARAMETERS M MODIFY MISCELLANEOUS PARAMETERS T MODIFY TRUNK RESERVATION PARAMETERS V MODIFY GPRS PARAMETERS X MODIFY DATA SERVICE PARAMETERS Q CHECK IUO INTERFERING CELLS O OUTPUT BTS PARAMETERS U CHANGE SEGMENT OF BTS S CHANGE BTS ADMINISTRATIVE STATE TRANSCEIVER DATA HANDLING COMMANDS C CREATE TRANSCEIVER D DELETE TRANSCEIVER M MODIFY TRANSCEIVER AND RADIO TIME SLOT PARAMETERS T MODIFY TRANSCEIVER BINARY OUTPUTS Y MODIFY TRANSCEIVER UNDERLAY-OVERLAY PARAMETERS O OUTPUT TRANSCEIVER PARAMETERS S CHANGE TRANSCEIVER AND RADIO TIME SLOT STATE ABIS INTERFACE CONFIGURATION COMMANDS TRUNK RESERVATION DECISION TABLE HANDLING COMMANDS C CREATE DECISION THRESHOLD TABLE D DELETE DECISION THRESHOLD TABLE M MODIFY DECISION THRESHOLD PARAMETERS O OUTPUT DECISION THRESHOLD PARAMETERS POWER CONTROL PARAMETER HANDLING COMMANDS C CREATE POWER CONTROL PARAMETERS G MODIFY GENERAL PARAMETERS A MODIFY AVERAGING PARAMETERS M MODIFY DATA SERVICE PARAMETERS Q MODIFY SIGNAL QUALITY THRESHOLD PARAMETERS S MODIFY SIGNAL STRENGTH THRESHOLD PARAMETERS O OUTPUT POWER CONTROL PARAMETERS BCF HW DATABASE HANDLING COMMANDS C CREATE BCF HW DATABASE D DELETE BCF HW DATABASE A ATTACH HW DATABASE TO BCF
E V S T L O U R ZE
W
ZE
X
ZE
Y
DETACH HW DATABASE FROM BCF ACTIVATE BCF HW DATABASE REPLACE HW DATABASE LIST BCFs ATTACHED TO SAME HW DATABASE LIST EXISTING BCF HW DATABASES LIST HW DATABASE CONFIGURATION OF BCF UPLOAD HW DATABASE FILE(S) ERASE BCF NON-VOLATILE MEMORY
BCF SOFTWARE HANDLING COMMANDS C CREATE BCF SOFTWARE BUILD D DELETE BCF SOFTWARE BUILD A ATTACH SOFTWARE BUILD TO BCF E DETACH SOFTWARE BUILD FROM BCF V ACTIVATE BCF SOFTWARE BUILD H CHANGE STATUSES OF TWO BCF SOFTWARE BUILDS S SET OR REMOVE INITIAL SOFTWARE BUILD I LIST BCF SOFTWARE HANDLING SYSTEM ACTIVITIES L LIST EXISTING BCF SOFTWARE BUILDS O LIST SOFTWARE CONFIGURATION OF BCF P LIST BCF SOFTWARE BUILD CONTENTS POSITION BASED SERVICES HANDLING COMMANDS N MODIFY SMLC PARAMETERS Q OUTPUT SMLC PARAMETERS C CREATE LCS ELEMENT D DELETE LCS ELEMENT M MODIFY LCS ELEMENT PARAMETERS O OUTPUT LCS ELEMENT PARAMETERS A CREATE LMU AREA R DELETE LMU AREA B MODIFY LMU AREA PARAMETERS I OUTPUT LMU AREA PARAMETERS E CREATE RIT TRANSFER TABLE F DELETE RIT TRANSFER TABLE G MODIFY RIT TRANSFER TABLE PARAMETERS P OUTPUT RIT TRANSFER TABLE PARAMETERS H CREATE REPEATER K DELETE REPEATER T MODIFY REPEATER PARAMETERS L OUTPUT REPEATER PARAMETERS HUNTING ORDER HANDLING COMMANDS I INTERROGATE SPEECH CODEC POOL LIST(S M MODIFY SPEECH CODEC POOL LIST R RESTORE SPEECH CODEC DEFAULT LISTS
ZF
FRAME RELAY ADMINISTRATION
ZF
N
ZF
U
FRAME RELAY NODE PARAMETER HANDLING COMMANDS S MODIFY LOCAL BEARER CHANNEL SIGNALLING PARAMETERS O INTERROGATE LOCAL BEARER CHANNEL SIGNALLING PARAMETERS FRAME RELAY BEARER CHANNEL HANDLING C CREATE FRAME RELAY BEARER CHANNEL M MODIFY FRAME RELAY BEARER CHANNEL DATA
ZF
W
D DELETE FRAME RELAY BEARER CHANNEL I INTERROGATE FRAME RELAY BEARER CHANNEL DATA NETWORK SERVICE VIRTUAL CONNECTION HANDLING COMMANDS C CREATE NETWORK SERVICE VIRTUAL CONNECTION D DELETE NETWORK SERVICE VIRTUAL CONNECTION M MODIFY NETWORK SERVICE VIRTUAL CONNECTION S CHANGE THE STATE OF NETWORK SERVICE VIRTUAL CONNECTION O OUTPUT THE NETWORK SERVICE VIRTUAL CONNECTION DATA
ZI
I/O SYSTEM ADMINISTRATION
ZI
A
ZI
B
ZI
C
ZI
D
ZI
E
MMI SYSTEM AUTHORITY HANDLING COMMANDS A CREATE OR MODIFY PROFILE R DELETE PROFILE H CREATE USER ID D DELETE USER ID E ATTACH PROFILE TO USER ID OR TERMINAL G CHANGE OWN PASSWORD S CHANGE PASSWORD OF OTHER USER ID F CHANGE SERVICE TERMINAL PASSWORD Q RESET LOGIN DELAYS X MODIFY MML SESSION TIME LIMIT K CHANGE ENCRYPTION METHOD M CHANGE COMMAND DEFINITIONS I INTERROGATE USER IDS, TERMINALS AND PROFILES T INTERROGATE COMMAND DEFINITIONS L INTERROGATE ALLOWED COMMANDS B BLOCK/UNBLOCK COMMAND O INTERROGATE BLOCKED COMMANDS I/O FILE BACKUP COMMANDS B COPY BYTES FROM STATISTICAL TAPE TO HARD DISK C COPY MASS MEMORY FILES D DELETE LAST FILE SET OF CTU F MOVE DATA FROM DISK BUFFER OF CTU P DUMP DATA FROM TAPE R RESTORE DATA FROM TAPE TO LOGICAL FILE T TYPE FILE X DISPLAY CONTENTS OF TAPE COMMAND CALENDAR HANDLING COMMANDS I ADD NEW COMMAND CALENDAR TASK M MODIFY COMMAND CALENDAR TASK D DELETE COMMAND CALENDAR TASK L LIST CALENDAR T TEST COMMAND CALENDAR TASK EXECUTION B BLOCK OR UNBLOCK COMMAND CALENDAR TASK S STOP COMMAND FILE EXECUTION DISK COMMAND FILE EXECUTION COMMAND COMMANDS E EXECUTE COMMAND FILE S STOP COMMAND FILE EXECUTION L LIST COMMAND FILE X EXECUTE REMOTE COMMAND DISK FILE OPERATIONS COMMANDS E EDIT DISK FILE
ZI
F
ZI
G
ZI
I
ZI
M
ZI
O
ZI
P
ZI
Q
VIRTUAL DATA STORING DEVICE HANDLING COMMANDS S SET DISK FILE STATUS A SET DISK ALARM LIMITS F DEFINE FILE AND STORING RELATED PARAMETERS N INITIALIZE VDS DEVICE T DEFINE TIME CONTROL FOR CHANGING DISK FILES M MODIFY FTAM ATTRIBUTES H DEFINE CONTROL FILE HANDLING Q DEFINE Q3 TRANSFER UP READY PARAMETERS C COPY DATA FILES O DISPLAY CONTROL FILES P DISPLAY FILE STATUS MAP I INTERROGATE DISK FILE INFORMATION MML COMMAND LOG HANDLING COMMANDS O DISPLAY MML COMMAND LOG K CLOSE MML COMMAND LOG FILE I/O CONFIGURATION HANDLING COMMANDS D DISPLAY INFORMATION OF GIVEN LOGICAL FILE S CHANGE OBJECT CONNECTED TO LOGICAL FILE L LIST LOGICAL FILES CONNECTED TO GIVEN OBJECT C CHANGE OBJECT TO ANOTHER IN ALL LOGICAL FILES F CREATE LOGICAL FILE P CREATE SPARE LOGICAL FILE R REMOVE LOGICAL FILE I LINK PHYSICAL DISK FILE TO LOGICAL FILE G CHANGE SIGNALLED PROCESS MAGNETIC TAPE HANDLING P PREMARK MAGNETIC TAPE O OPEN FILE ON MAGNETIC TAPE C CLOSE FILE ON MAGNETIC TAPE R RELEASE MAGNETIC TAPE D DISPLAY STATUS OF UNIT(S) AND TAPE(S) T CHANGE MAGNETIC TAPE F REOPEN FILE ON MAGNETIC TAPE I IDENTIFY TAPE AND RESERVE UNIT S SET TAPE TYPE E RESET TAPE UNIT M MODIFY/INTERROGATE TAPE CODING NETWORK USER AUTHORITY DATA HANDLING COMMANDS A ADD USER PROFILE M ADD USER ACCESS RIGHTS R REMOVE USER ACCESS RIGHTS E INTERROGATE NETWORK ELEMENT USERS I INTERROGATE USER PROFILE BATCH COPY HANDLING COMMANDS I INTERROGATE GENERAL COPY TASK INFORMATION P DISPLAY DETAILED COPY TASK LOG S START BACKUP COPY TASK T TERMINATE ONGOING COPY TASK X DISPLAY BACKUP COPIES ON REMOVABLE DISK DISK OPTIMIZATION CONTROL COMMANDS C CONFIGURE THE DISK CACHE
S DISPLAY CACHE STATISTICS V HANDLE DISK WRITE VERIFICATION SECURITY REPORTING HANDLING COMMANDS M MODIFY CRITICAL LIMITS R RESET LONG TERM COUNTERS T SET COUNTER REPORT OUTPUT TIME I INTERROGATE COUNTER REPORT OUTPUT PARAMETERS O DISPLAY DETAILED REPORT P PRINT COUNTER REPORT I/O DEVICE WORKING STATE COMMANDS C CHANGE I/O DEVICE STATE I INTERROGATE I/O DEVICE INFO L LIST I/O DEVICES IN SPECIFIED STATE M MODIFY SPARE DEVICE OF I/O DEVICE K MODIFY/INTERROGATE SCSI ADDRESS OF MTU F CHANGE FUNCTIONAL MODE OF CTU TERMINAL PARAMETERS HANDLING COMMANDS I INTERROGATE TERMINAL PARAMETERS M MODIFY TERMINAL PARAMETERS F SET TERMINAL OPERATION MODE DISK FILE AND DIRECTORY HANDLING B HANDLE BAD BLOCKS C CREATE FILE D DELETE FILE E EMPTY FILE F INTERROGATE/CHANGE DEFAULT VERSION I INITIALIZE DISK K INITIALIZE DIRECTORY L CREATE DIRECTORY M DELETE DIRECTORY N RENAME FILE P PACK DISK Q INTERROGATE/MODIFY DISK CONFIGURATION S SET FILE ATTRIBUTES X DISPLAY DIRECTORY Y INTERROGATE/CHANGE DEFAULT SETTINGS DISK FILE COMPRESSION HANDLING MML COMMANDS F COMPRESS FILE(S) TO ZIP ARCHIVE X EXTRACT FILE(S) FROM ZIP ARCHIVE L LIST CONTENTS OF ZIP ARCHIVE C COMPRESS FILE TO GZIP ARCHIVE E EXTRACT FILE FROM GZIP ARCHIVE I LIST CONTENTS OF GZIP ARCHIVE(S)
ZI
R
ZI
S
ZI
T
ZI
W
ZI
X
ZN
SS7 NETWORK ADMINISTRATION
ZN
A
GLOBAL TITLE RESULT HANDLING COMMANDS A CREATE GLOBAL TITLE MODIFICATION DATA C CREATE TRANSLATION RESULT D DELETE TRANSLATION RESULT I INTERROGATE TRANSLATION RESULTS M MODIFY TRANSLATION RESULT R DELETE GLOBAL TITLE MODIFICATION DATA
ZN
B
ZN
C
ZN
E
ZN
F
ZN
G
ZN
H
ZN
L
S MODIFY GLOBAL TITLE MODIFICATION DATA X INTERROGATE GLOBAL TITLE MODIFICATION DATA SCCP GLOBAL TITLE ANALYSIS HANDLING COMMANDS C CREATE OR ADD ANALYSIS D DELETE OR REMOVE ANALYSIS I INTERROGATE OR SEARCH ANALYSIS J INTERROGATE ROOTS OF ANALYSIS TREES SIGNALLING LINK DATA HANDLING COMMANDS COMMANDS C CREATE SIGNALLING LINK M MODIFY SIGNALLING LINK D DELETE SIGNALLING LINK I INTERROGATE SIGNALLING LINK DATA L CHANGE PARAMETER SET O EXCHANGE PARAMETER SET OF SIGNALLING LINKS SIGNALLING NETWORK STATE INTERROGATION COMMANDS R INTERROGATE SIGNALLING ROUTE SET STATES S INTERROGATE SIGNALLING LINK SET STATES L INTERROGATE SIGNALLING LINK STATES T INTERROGATE NETWORK ITEM STATES O INTERROGATE SIGNALLING POINT LOAD SHARING P INTERROGATE PROHIBITED STP MESSAGES J RUN SIGNALLING ROUTING TEST SCCP DATA HANDLING COMMANDS D DEFINE SCCP FOR SIGNALLING POINT E DEFINE SCCP FOR SIGNALLING POINTS WITH SUBSYSTEMS COPY R REMOVE SCCP FROM SIGNALLING POINTS A ADD REPLICATIVE SIGNALLING POINT S REMOVE REPLICATIVE SIGNALLING POINT B ADD SUBSYSTEMS TO SIGNALLING POINTS T REMOVE SUBSYSTEM FROM SIGNALLING POINTS C ADD REPLICATIVE SUBSYSTEM U REMOVE REPLICATIVE SUBSYSTEM I INTERROGATE SCCP DATA OF SIGNALLING POINTS J INTERROGATE SUBSYSTEMS DATA OF SIGNALLING POINTS L CHANGE SCCP SIGNALLING POINT PARAMETER SET M CHANGE SUBSYSTEM PARAMETER SET N EXCHANGE PARAMETER SET OF SCCP SIGNALLING POINT O EXCHANGE PARAMETER SET OF SUBSYSTEM P CHANGE SUBSYSTEM TEST STATUS SCCP STATE HANDLING COMMANDS C CHANGE SCCP STATE D CHANGE REPLICATION STATE I INTERROGATE SCCP STATE SCCP SUBSYSTEM STATE HANDLING COMMANDS C CHANGE SUBSYSTEM STATE D CHANGE SUBSYSTEM REPLICATION STATE I INTERROGATE SUBSYSTEM STATE J INTERROGATE SUBSYSTEM DISTRIBUTION DATA SIGNALLING LINK STATE HANDLING COMMANDS C CHANGE SIGNALLING LINK STATE D DENY ACTIVATION OF SIGNALLING LINKS A ALLOW ACTIVATION OF SIGNALLING LINKS
ZN
M
ZN
N
ZN
O
ZN
P
ZN
R
ZN
S
I INTERROGATE SIGNALLING LINK STATES T TEST SIGNALLING DATA LINK O INTERROGATE SIGNALLING DATA LINK TEST J RUN SIGNALLING LINK ROUTING TEST CCS7 LEVEL 3 PARAMETERS HANDLING COMMANDS M MODIFY CCS7 LEVEL 3 PARAMETER I INTERROGATE CCS7 LEVEL 3 PARAMETERS C MODIFY CCS7 NETWORK SPECIFIC PARAMETER O INTERROGATE CCS7 NETWORK SPECIFIC PARAMETERS SIGNALLING ROUTE SET PARAMETER SET HANDLING COMMANDS C CREATE SIGNALLING ROUTE SET PARAMETER SET E COPY SIGNALLING ROUTE SET PARAMETER SET M MODIFY SIGNALLING ROUTE SET PARAMETER SET N CHANGE SIGNALLING ROUTE SET PARAMETER SET NAME D DELETE SIGNALLING ROUTE SET PARAMETER SET I INTERROGATING SIGNALLING ROUTE SET PARAMETER SETS SIGNALLING LINK PARAMETER SET HANDLING COMMANDS C CREATE SIGNALLING LINK PARAMETER SET E COPY SIGNALLING LINK PARAMETER SET M MODIFY SIGNALLING LINK PARAMETER SET N CHANGE SIGNALLING LINK PARAMETER SET NAME D DELETE SIGNALLING LINK PARAMETER SET I INTERROGATE SIGNALLING LINK PARAMETER SETS SERVICE INFORMATION DATA HANDLING COMMANDS C CREATE SERVICE M MODIFY SERVICE D DELETE SERVICE I INTERROGATE SERVICES U UPDATE STP-SERVICE SIGNALLING ROUTE SET DATA HANDLING COMMANDS P MODIFY OWN SIGNALLING POINT DATA C CREATE SIGNALLING ROUTE SET B MODIFY DATA OF SIGNALLING ROUTE SET D DELETE SIGNALLING ROUTE SET A ADD SIGNALLING ROUTE TO ROUTE SET R DELETE SIGNALLING ROUTE FROM ROUTE SET E CHANGE SIGNALLING ROUTE PRIORITY N CHANGE SIGNALLING POINT NAME I INTERROGATE SIGNALLING POINT DATA S CHANGE STP ACCESS T INTERROGATE STP ACCESS X EXCHANGE ADJACENT SIGNALLING POINT CODE V VERIFY OF MTP ROUTING DATA CHAINS F REPAIR OF MTP ROUTING DATA CHAINS SIGNALLING LINK SET DATA HANDLING COMMANDS C CREATE SIGNALLING LINK SET A ADD SIGNALLING LINK TO LINK SET R DELETE SIGNALLING LINK FROM LINK SET N CHANGE SIGNALLING LINK SET NAME S CHANGE SIGNALLING LINK CODE D DELETE SIGNALLING LINK SET I INTERROGATE SIGNALLING LINK SET DATA
T CHANGE SIGNALLING LINK TEST STATUS SIGNALLING ROUTE STATE HANDLING COMMANDS C CHANGE SIGNALLING ROUTE STATE D DENY ACTIVATION OF SIGNALLING ROUTE A ALLOW ACTIVATION OF SIGNALLING ROUTE I INTERROGATE SIGNALLING ROUTE STATES
ZN
V
ZO
SUPPLEMENTARY SS7 NETWORK ADMINISTRATION
ZO
B
ZO
C
ZO
D
ZO
I
ZO
L
ZO
M
SCCP BROADCAST STATUS HANDLING COMMANDS COMMANDS M MODIFY BROADCAST STATUS OF SCCP SIGNALLING POINTS I INTERROGATE BROADCAST STATUS OF SCCP SIGNALLING POINTS C MODIFY LOCAL BROADCAST STATUS OF SCCP SUBSYSTEMS L INTERROGATE LOCAL BROADCAST STATUS OF SCCP SUBSYSTEMS SCCP PARAMETER SET HANDLING COMMANDS C CREATE SCCP SIGNALLING POINT PARAMETER SET A CREATE SCCP SUBSYSTEM PARAMETER SET E COPY SCCP SIGNALLING POINT PARAMETER SET F COPY SCCP SUBSYSTEM PARAMETER SET M MODIFY SCCP SIGNALLING POINT PARAMETER SET N MODIFY SCCP SUBSYSTEM PARAMETER SET R CHANGE PARAMETER SET NAME D DELETE SCCP SIGNALLING POINT PARAMETER SET K DELETE SCCP SUBSYSTEM PARAMETER SET I INTERROGATE SCCP SIGNALLING POINT PARAMETER SETS J INTERROGATE SCCP SUBSYSTEM PARAMETER SETS H HELP TEXT FOR SCCP SIGNALLING POINT PARAMETERS L HELP TEXT FOR SCCP SUBSYSTEM PARAMETERS SCCP SCREENING HANDLING COMMANDS C COPY SCCP SCREENING DATA FROM MTP I INTERROGATE SCCP SCREENING DATA M MODIFY SCCP SCREENING S MODIFY SCCP SCREENING STATUS MANAGEMENT OF TRAFFIC MATRIX MEASUREMENT FOR MTP COMMANDS S DEFINE MAXIMUM COUNTS OF INDEXES I INTERROGATE MAXIMUM COUNTS OF INDEXES O CONNECT OP/DP INDEX TO SIGNALLING POINT E DELETE OP/DP INDEX D LIST ALL OP/DP INDEXES A DELETE ALL OP/DP INDEXES U CONNECT SI INDEX TO USER PART C DELETE SI INDEX P LIST ALL SI INDEXES L DELETE ALL SI INDEXES INTERROGATION OF SIGNALLING LINK STATISTICS METERS COMMANDS P INTERROGATE SIGNALLING LINK PERFORMANCE METERS A INTERROGATE SIGNALLING LINK AVAILABILITY METERS U INTERROGATE SIGNALLING LINK UTILIZATION METERS T INTERROGATE SIGNALLING LINK LOAD L INTERROGATE SIGNALLING LINK EVENT LOGS E EMPTY SIGNALLING LINK EVENT LOGS INTERROGATION OF AUXIALIARY MTP STATISTICS METERS COMMANDS Q INTERROGATE LEVEL 3 AUXILIARY METERS
ZO
N
ZO
S
ZO
T
T INTERROGATE SIGNALLING LINK TERMINAL METERS I INTERROGATE MTP LEVEL 2 METERS S INTERROGATE ATM BASED SIGNALLING LINK SAAL METERS INTERROGATION OF SIGNALLING NETWORK STATISTICS METERS COMMANDS A SIGNALLING LINK SET AND ROUTE SET AVAILABILITY METERS S SIGNALLING POINT STATUS METERS P SIF AND SIO METERS HANDLED WITH SP I SIF AND SIO METERS HANDLED WITH SIO T SIF, SIO AND MSU METERS HANDLED WITH OPC, DPC AND SIO E EMPTY SIGNALLING POINT EVENT LOGS L INTERROGATE SIGNALLING POINT EVENT LOGS STATES OF SS7 STATISTICS COMMANDS A ACTIVATE SS7 STATISTICS AND REPORTS D DEACTIVATE SS7 STATISTICS AND REPORTS E INTERROGATE REPORTING STATUS OF SCCP SUBSYSTEMS F MODIFY REPORTING STATUS OF SCCP SUBSYSTEMS I INTERROGATE STATES OF SS7 STATISTICS J INTERROGATE REPORTING STATUS OF SIGNALLING LINKS K INTERROGATE REPORTING STATUS OF SIGNALLING POINTS L MODIFY REPORTING STATUS OF SIGNALLING LINKS M MODIFY SS7 MEASUREMENT REPORT PARAMETERS N MODIFY REPORTING STATUS OF SIGNALLING POINTS R INTERROGATE SS7 MEASUREMENT REPORT PARAMETERS G MODIFY STATES OF INTERVAL LOG REPORTS Q INTERROGATE STATES OF INTERVAL LOG REPORTS INTERROGATION OF SCCP AND TC STATISTICS METERS COMMANDS N SCCP SIGNALLING POINT METERS S SCCP SUBSYSTEM METERS J SCCP SUBSYSTEM METERS OF SIGNALLING POINT A SCCP LOCAL SUBSYSTEM AVAILABILITY METERS I INTERROGATE SCCP SINGLE METERS G INTERROGATE SCCP SEGMENTATION AND REASSEMBLY ERROR METERS Q SCCP QUALITY OF SERVICE METERS E EMPTY SCCP OR TC EVENT LOG O INTERROGATE SCCP SIGNALLING POINT EVENT LOG L INTERROGATE SCCP SUBSYSTEM EVENT LOG R INTERROGATE SCCP MESSAGE HANDLING FAILURE LOG U INTERROGATE TC UTILIZATION METERS T INTERROGATE TC TRANSACTION METERS P INTERROGATE TC FAULT METERS F INTERROGATE TC EVENT LOG
ZQ
O&M NETWORK ADMINISTRATION
ZQ
B
NETWORK ADDRESS AND NSAP DATA HANDLING COMMANDS C CREATE NETWORK ADDRESS D DELETE NETWORK ADDRESS I INTERROGATE NETWORK ADDRESS DATA N CREATE NSAP M MODIFY NSAP DATA R DELETE NSAP T ATTACH NSAP TO NETWORK ADDRESS F DETACH NSAP FROM NETWORK ADDRESS
ZQ
C
ZQ
D
ZQ
E
ZQ
F
ZQ
G
ZQ
H
H SET DEFAULT VALUES FOR ISO DCC AND ISO 6253-ICD NSAP G CHANGE NSAP STATE L INTERROGATE NETWORK NSAP DATA PHYSICAL CHANNEL DATA HANDLING COMMANDS C CREATE PHYSICAL CHANNEL THROUGH DIGITAL TERMINAL S CREATE PHYSICAL CHANNEL THROUGH ANALOG TERMINAL M MODIFY PHYSICAL CHANNEL THROUGH DIGITAL TERMINAL U MODIFY PHYSICAL CHANNEL THROUGH ANALOG TERMINAL D DELETE PHYSICAL CHANNEL I INTERROGATE PHYSICAL CHANNEL DATA OSI ENVIRONMENT APPLICATION DATA HANDLING COMMANDS L CREATE LOCAL OSI APPLICATION R CREATE REMOTE OSI APPLICATION M MODIFY LOCAL OSI APPLICATION DATA H MODIFY REMOTE OSI APPLICATION DATA N MODIFY OSI APPLICATION NAME D DELETE OSI APPLICATION I INTERROGATE OSI APPLICATION DATA A ADD SERVICE PROFILE TO OSI APPLICATION C MODIFY SERVICE PROFILE OF OSI APPLICATION E DETACH SERVICE PROFILE FROM OSI APPLICATION T ATTACH SECONDARY SELECTOR GROUP TO OSI APPLICATION F DETACH OR MODIFY SECONDARY SELECTOR GROUP G CHANGE OSI APPLICATION STATE OSI ENVIRONMENT CONNECTIONLESS NETWORK SERVICE HANDLING COMMANDS C CREATE CLNS M MODIFY CLNS DATA A ADD MANUAL AREA ADDRESS TO CLNS R REMOVE MANUAL AREA ADDRESS FROM CLNS N MODIFY CLNS NAME F MODIFY CLNS PARAMETERS T RESTART CLNS G CHANGE CLNS STATE D DELETE CLNS H ACCEPT NEW CLNS I INTERROGATE CLNS DATA OSI FILE SERVICES A COPY FILE C CREATE FILE D DELETE FILE L LIST FILE DIRECTORY M MODIFY FILE ATTRIBUTES PHYSICAL CHANNEL GROUP DATA HANDLING COMMANDS C CREATE PHYSICAL CHANNEL GROUP A ADD PHYSICAL CHANNEL TO PHYSICAL CHANNEL GROUP R DELETE PHYSICAL CHANNEL FROM PHYSICAL CHANNEL GROUP N CHANGE PHYSICAL CHANNEL GROUP NAME M CHANGE PHYSICAL CHANNEL DATA D DELETE PHYSICAL CHANNEL GROUP I INTERROGATE PHYSICAL CHANNEL GROUP DATA ETHERNET TERMINAL DATA HANDLING COMMANDS C CREATE ETHERNET TERMINAL DATA
ZQ
L
ZQ
N
ZQ
Q
ZQ
R
ZQ
S
ZQ
T
M MODIFY ETHERNET TERMINAL DATA D DELETE ETHERNET TERMINAL DATA I INTERROGATE ETHERNET TERMINAL DATA OSI ENVIRONMENT LINKAGE HANDLING COMMANDS C CREATE X.25 LINKAGE L CREATE BROADCAST LINKAGE M MODIFY X.25 LINKAGE DATA R MODIFY BROADCAST LINKAGE G CHANGE LINKAGE STATE F MODIFY LINKAGE PARAMETERS D DELETE LINKAGE I INTERROGATE LINKAGE DATA A ADD MANUAL ES ADJACENCY TO LINKAGE E REMOVE MANUAL ES ADJACENCY FROM LINKAGE P INTERROGATE LINKAGE ADJACENCY INFORMATION O&M NETWORK HANDLING A ADD NEW O&M CONNECTION C CHANGE WORKING STATE OF O&M CHANNEL D DELETE O&M CONNECTION I INTERROGATE O&M NETWORK CONFIGURATION M MODIFY O&M CONNECTION N INTERROGATE OCCASIONAL VALUES OF O&M CHANNEL METERS S DISPLAY MML SESSIONS ACCESS CONTROL DATA HANDLING COMMANDS C ADD SNPA TO OSI ACCESS CONTROL LIST M MODIFY OSI ACCESS CONTROL METHOD D DELETE SNPA FROM OSI ACCESS CONTROL LIST I INTERROGATE OSI ACCESS CONTROL DATA TCP/IP STACK DATA HANDLING COMMANDS N CONFIGURE NETWORK INTERFACE G REMOVE NETWORK INTERFACE W FORCE INTERFACE SWITCHOVER I INTERROGATE NETWORK INTERFACE IP ADRESSES T CONFIGURE TCP/IP PARAMETERS H INTERROGATE TCP/IP PARAMETERS C CREATE STATIC ROUTE D DELETE STATIC ROUTE L INTERROGATE STATIC ROUTES K CONFIGURE DNS PARAMETERS J INTERROGATE DNS PARAMETERS R RESET TCP/IP NETWORK COMMUNICATIONS ENVIRONMENT F DISTRIBUTE CONFIGURATION FILE X TEST HOST REACHABILITY (PING) S INTERROGATE NETWORK STATUS PHYSICAL CHANNEL STATE HANDLING C CHANGE PHYSICAL CHANNEL STATE I INTERROGATE PHYSICAL CHANNEL STATES ANALOG TERMINAL DATA HANDLING COMMANDS C CREATE ANALOG TERMINAL DATA M MODIFY ANALOG TERMINAL DATA D DELETE ANALOG TERMINAL DATA I INTERROGATE ANALOG TERMINAL DATA
ZQ
U
BSS TRANSMISSION EQUIPMENT HANDLING COMMANDS S START REMOTE SESSION E EXECUTE REMOTE COMMAND A ADD EQUIPMENT DATA D DELETE EQUIPMENT DATA M MODIFY EQUIPMENT DATA P DISPLAY EQUIPMENT DATA F HANDLE EQUIPMENT COLLECTION AND CHECKSUM POLLING B ADD OBJECT TO TRANSMISSION MEASUREMENT R REMOVE OBJECT FROM TRANSMISSION MEASUREMENT I INTERROGATE TRANSMISSION MEASUREMENT OBJECTS C CREATE TRANSMISSION EQUIPMENT SOFTWARE BUILD G DELETE TRANSMISSION EQUIPMENT SOFTWARE BUILD T ATTACH EQUIPMENT TO SOFTWARE BUILD U DETACH EQUIPMENT FROM SOFTWARE BUILD H HANDLE SOFTWARE BUILD DATA L LIST SOFTWARE BUILD DATA VIRTUAL TERMINAL COMMUNICATION COMMANDS C CONNECT I INTERROGATE PAD PARAMETERS M MODIFY PAD PARAMETERS P DISPLAY CONNECTION INFORMATION D DISCONNECT Q1 INTERFACE HANDLING COMMANDS C CREATE SERVICE CHANNEL D DELETE SERVICE CHANNEL M MODIFY SERVICE CHANNEL CONFIGURATION S SET SERVICE CHANNEL STATE I INTERROGATE SERVICE CHANNEL CONFIGURATION A ADD EQUIPMENT TO SERVICE CHANNEL R REMOVE EQUIPMENT FROM SERVICE CHANNEL G CHANGE EQUIPMENT INFORMATION F MODIFY BTS Q1 BUS PARAMETER L LIST EQUIPMENT X25 CONFIGURATION PARAMETERS HANDLING COMMANDS C CREATE X25 CONFIGURATION PARAMETER SET DATA M MODIFY X25 CONFIGURATION PARAMETER SET DATA F ADD AND REMOVE X25 INTERFACE FACILITIES D DELETE X25 CONFIGURATION PARAMETER SET DATA I INTERROGATE X25 CONFIGURATION PARAMETERS
ZQ
V
ZQ
W
ZQ
X
ZR
ROUTING ADMINISTRATION
ZR
B
ZR
C
SEMIPERMANENT BROADBAND CONNECTIONS HANDLING A CREATE BROADBAND CONNECTION B CREATE POINT-TO-MULTIPOINT BROADBAND CONNECTION I INTERROGATE SEMIPERMANENT BROADBAND CONNECTIONS M MODIFY POINT-TO-MULTIPOINT BROADBAND CONNECTION P DELETE BROADBAND CONNECTION R DELETE POINT-TO-MULTIPOINT BROADBAND CONNECTION X UPDATE BOOKED TIME CIRCUIT GROUP HANDLING COMMANDS C CREATE CIRCUIT GROUP
A ADD CIRCUITS TO CIRCUIT GROUP N MODIFY CIRCUIT GROUP M MODIFY ADDITIONAL CIRCUIT GROUP PARAMETERS I INTERROGATE CIRCUIT GROUP R REMOVE CIRCUITS FROM CIRCUIT GROUP D DELETE CIRCUIT GROUP ROUTE HANDLING COMMANDS C CREATE ROUTE A ADD CIRCUIT GROUP M MODIFY ROUTE D DELETE ROUTE / CIRCUIT GROUP I INTERROGATE ROUTE
ZR
R
ZT
TRAFFIC ADMINISTRATION
ZT
P
ZT
V
GSM MEASUREMENT HANDLING COMMANDS M MODIFY GSM MEASUREMENT CHARACTERISTICS I INTERROGATE GSM MEASUREMENT S START GSM MEASUREMENT E STOP GSM MEASUREMENT BSC MEASUREMENTS COUNTERS INQUIRY COMMANDS I INQUIRE AND OUTPUT COUNTERS O OUTPUT COUNTERS S SHOW DESCRIPTION OF THE COUNTERS R RESET THE COUNTERS
ZU
UNIT ADMINISTRATION
ZU
B
ZU
C
ZU
D
SINGLE RADIO NETWORK TEST HANDLING COMMANDS E SYNCHRONIZE BCCH FOR TERMINATING TEST CALL F START CALL STATUS REQUEST G START ORIGINATING TEST CALL H START BCCH FIELD STRENGTH MEASUREMENT J START RECEIVER SENSITIVITY MEASUREMENT K HANDLE ABIS LOOP TEST L LIST ACTIVE ABIS LOOP TESTS N INTERRUPT TEST R START ANTENNA TEST S START TRANSCEIVER TEST P PRINT TEST REPORT D DELETE TEST REPORT SCHEDULED RADIO NETWORK TEST HANDLING COMMANDS C CREATE SCHEDULED TEST D DELETE SCHEDULED TEST I INTERROGATE SCHEDULED TEST M MODIFY SCHEDULED TEST FUNCTIONAL PARAMETERS S CHANGE SCHEDULED TEST STATE T MODIFY TIME PARAMETERS OF SCHEDULED TEST V HANDLE THRESHOLD PARAMETERS DIAGNOSTICS HANDLING COMMANDS U START UNIT TEST/PARTIAL UNIT TEST D START I/O DEVICE TEST H OUTPUT DIAGNOSTIC REPORT HISTORY I INTERROGATE PARTIAL UNIT TESTS L LIST FAULTY UNITS/PROCESSOR UNITS
ZU
S
Q INTERROGATE CURRENT TESTS S STOP CURRENT TEST WORKING STATE AND RESTART HANDLING COMMANDS C CHANGE UNIT STATE T CHANGE UNIT INFO W WARM UP SPARE UNIT I INTERROGATE UNIT STATE L LIST UNITS IN SPECIFIED STATE OR INFO U RESTART UNIT S RESTART SYSTEM
ZW
SYSTEM CONFIGURATION ADMINISTRATION
ZW
A
ZW
B
ZW
G
ZW
I
ZW
K
ZW
N
WIRED ALARM CONNECTIONS HANDLING COMMANDS O OPEN ALARM CONNECTION C CLOSE ALARM CONNECTION I OPEN ALARM INPUT D CLOSE ALARM INPUT X MODIFY ALARM INPUT PARAMETERS P PRINT OPEN CONNECTIONS/INPUTS A CREATE EXTERNAL ALARM M MODIFY EXTERNAL ALARM PARAMETERS R REMOVE EXTERNAL ALARM T PRINT EXTERNAL ALARMS E TEST CARTRIDGE ALARMS COMPUTER CONFIGURATION HANDLING COMMANDS A ADD MESSAGE BUS ADDRESS M MODIFY MESSAGE BUS ADDRESS R REMOVE MESSAGE BUS ADDRESS E DELIVER DATA TO ALL COMPUTERS I INTERROGATE COMPUTER CONFIGURATION TRANSCODER CONFIGURATION COMMANDS C CREATE TRANSCODER PCM D DELETE TRANSCODER PCM M MODIFY TRANSCODER PCM O OUTPUT TRANSCODER PCM INFORMATION S SET NUMBER OF THROUGH CONNECTED CHANNELS A ADD THROUGH CONNECTED CHANNEL R REMOVE THROUGH CONNECTED CHANNEL F FETCH THROUGH CONNECTIONS FROM TRANSCODER I INTERROGATE ROUTINE TEST INFORMATION T MODIFY ROUTINE TEST DATA AND PARAMETERS INTERNAL PCM CIRCUITS CONFIGURATION COMMANDS P INTERROGATE PCM CIRCUITS OF IDENTIFIED SWITCH L INTERROGATE PCM CIRCUITS OF IDENTIFIED COMPUTER OR PROGRAM BLOCK SOFTWARE PACKAGE FALLBACK HANDLING COMMANDS S START FALLBACK COPYING Q QUIT FALLBACK COPYING I INTERROGATE FALLBACK COPYING P DISPLAY FALLBACK LOGFILE CHANGE DELIVERY HANDLING COMMANDS A ADD CHANGE DELIVERY D DELETE CHANGE DELIVERY
ZW
O
ZW
Q
ZW
R
ZW
S
ZW
T
ZW
U
ZW
X
H LIST CHANGE DELIVERY HISTORY I INTERROGATE CHANGE DELIVERY J UPDATE PACKAGE IDENTIFIER PARAMETER HANDLING COMMANDS C CHANGE PARAMETER VALUE I INTERROGATE PARAMETER VALUE A ACTIVATE/DEACTIVATE OPTIONAL FEATURE S OUTPUT FEATURES ACTIVATION STATUS SOFTWARE PACKAGE ADMINISTRATION COMMANDS B VERIFY SOFTWARE PACKAGE C CREATE SOFTWARE PACKAGE D DELETE SOFTWARE PACKAGE H LIST SOFTWARE PACKAGE CHANGE HISTORY L LIST SOFTWARE PACKAGE CONTENTS M COMPARE SOFTWARE PACKAGES O SHOW SOFTWARE PACKAGE INFORMATION V INTERROGATE MODULE VERSION LOADED IN UNIT SOFTWARE PACKAGE DEPLOYMENT HANDLING COMMANDS A ADD UNITS TO TRIAL CONFIGURATION R REMOVE UNIT FROM TRIAL CONFIGURATION D DESTROY TRIAL CONFIGURATION S CUTOVER TO NEW SOFTWARE PACKAGE O RETURN TO OLD SOFTWARE PACKAGE C COMPLETE NEW CONFIGURATION SOFTWARE PACKAGE STATUS HANDLING COMMANDS D SELECT DEFAULT SOFTWARE PACKAGE C CHANGE STATUS OF TWO SOFTWARE PACKAGES S SWITCH ACTIVE PACKAGE IN DIRECTORY A ALLOW AUTOMATIC RETURN TO SPARE PACKAGE B DENY AUTOMATIC RETURN TO SPARE PACKAGE R ROLLBACK STATUSES OF CREATED PACKAGES I INTERROGATE AUTOMATIC RETURN SETTINGS EQUIPMENT MANAGEMENT COMMANDS J CREATE RACK OR CABINET K DELETE RACK OR CABINET C CREATE CARTRIDGE D DELETE CARTRIDGE U CREATE UNIT V DELETE UNIT P CREATE PLUG-IN UNIT Q DELETE PLUG-IN UNIT F CREATE FUNCTION G DELETE FUNCTION I INTERROGATE INFORMATION L LIST EQUIPMENT IN CSV-FORMAT UNIT CONNECTIONS HANDLING COMMANDS C CONNECT FUNCTIONAL UNIT D DISCONNECT FUNCTIONAL UNIT SOFTWARE CONFIGURATION RESOURCE HANDLING COMMANDS E RESERVE OPERATION RESOURCES I RELEASE RESOURCE RESERVATION F INTERROGATE RESOURCES
P
DISPLAY OPERATION EXECUTION CONDITION
ZY
SYSTEM SUPERVISION
ZY
E
ZY
I
ZY
M
EXCHANGE TERMINAL SUPERVISION HANDLING COMMANDS M MODIFY ET PARAMETERS O OUTPUT ET PARAMETERS A MODIFY ALARM LIMITS P OUTPUT ALARM LIMITS S MODIFY STATISTICS COUNTERS LIMITS L OUTPUT STATISTICS COUNTERS LIMITS U MODIFY SLIP LIMITS R OUTPUT SLIP LIMITS G MODIFY T1 FUNCTIONAL MODES H OUTPUT T1 FUNCTIONAL MODES F INTERROGATE PCM SERVICE STATE V3 INTERFACE LOOPBACK HANDLING COMMANDS C CREATE LOOPBACK(S) R REMOVE LOOPBACK(S) I INTERROGATE LOOPBACK(S) PCM STATISTICS: MEASUREMENT AND OUTPUT COMMANDS C CANCEL TEMPORARY MEASUREMENT O OUTPUT STATISTICAL DISTURBANCES ON ONE CIRCUIT P OUTPUT MEASUREMENT PERIOD PARAMETERS S START TEMPORARY MEASUREMENT
BABELEGIVCG1
MSC Trace Calls LAC ID TABLE VLRMTC SGSN Link Routing
Logging For GPRS 1. Capture the PCU logs while the fault is active a. Determine to which BCSU the BTS which is experiencing the fault is connected to. To do this first verify if the fault is indeed on that specific BTS by using the ZEEI:BTS=; repeatedly and see if the timeslots are indeed appearing and disappearing. b. After having verified the that BTS is indeed having the fault use the ZEQO:BTS=:GPRS; to determine the NSEI to which the BTS is connected to. c. Use the ZFWO:NSEI=; to determine which BCSU the BTS is connected to for GPRS. The is d. After having determined the BCSU number from step c start a remote service terminal session to the BCSU: ZDDS:BCSU,; e. In the service terminal session start a remote session to the PCU: ZRS:3,90BE; example: for BCSU -1 ZRS:31,90BE f. Load the LGLVST command: dxfload -n LGLVSTSX -d -u 0 -o /bin/setlog.gz g. Set new loglevel for DAM programblock setlog dam 2
h. Exit the service terminal session by first typing 'exit' then type 'ZE' i. Define the log file j. Set logfile parameters ZDVM:CRIERR&INF&TES::BCSU,:PCU,4; k. Give following command after GP RTSL channels starts to go on/off (DO NOT FORGET TO CAPTURE THE LOGS TO A TEXT FILE. THIS LOGFILE NEEDS TO BE SENT TO NOKIA) ZDVL:BEG:CONT::::INT:BCSU,; l. Delete the sublog file with the ZDVD:; m. Stop the loging in the PCU by doing the following commands: ZDDS:BCSU,; ZRS:3,90BE; setlog dam 0
exit ZE 2. Capture the BSC connections: a. Determine the working MCMU ZUSI:MCMU; b. Start are remote service terminal session to the WO-EX MCMU ZDDS:MCMU,; Where - the index of the WO-EX MCMU found in step a. c. Load the FCHECK program ZL:1 ZLE:1,FCHECKGX; Z1CA; <===========Capture the output of this command and send it to Nokia d. Exit the service terminal session ZE
FILE HANDLING TOP LEVEL COMMANDS Looks at active Software Package on Winchestor drives Changes Default Software Package - Restarts BSC Rollback Packages FB>BU BU>NW NW>UT Switch Active Package In Directory Change Status Of Two Software Packages Changes software package into FB
FLOPPY DRIVE UNIT Listing Directories & Files on Floppy Displays contents on Floppy
Creating Directories & Subdirectories on Floppy Creates Directory on Floppy Create sub-directories on Floppy
Deleting Directories & files from Floppy Deleting File from Floppy Deleting Directories on Floppy
Moving Files on Floppy Sets source as Floppy drive Sets Destination as Winchester system & B/U drives Copies Source to Destination
DAT TAPE DRIVE UNIT Status Hard drives Status drives
Listing Directories & Files on Dat tape Displays fileset path & files Shows directory structure
Creating Directories & Subdirectories on Dat tape Creating Directory on Dat Tape Creating Subdirectory on Dat Tape
Deleting Directories & Files from Dat tape Deleting File from Dat Tape Deleting Directories from Dat Tape
Moving Directories & Files on Dat tape These 3 commands work together
Sets source copy Sets Destination - copies dat tape root to hardrive root in OMU Copies from selected source to selected destination
WINCHESTER HARD DRIVES IN OMU Listing Directories & Files on Hard drives Tape Lists Directories on B/U Winchester drive Lists Directories on System Winchester drive Lists Directories on System & b/u Winchester drives Views subdirectories on System Drive
Creating Directories & Subdirectories on Hard drives Creates Directory on Winchester drives Create sub-directories on Winchester drives
Deleting Directories & Files from Hard Drives Deleting Directory from Hard drive Deleting Files from Hard Drive
Moving Directories & Files on Dat tape Winchester drives to Dat Copy from selected source to selected Destination
Service Terminal Enter service terminal Link for copying in Service terminal Mass Memory Handling
Service Terminal Enter service terminal Link for copying in Service terminal
ZWQO:CR; ZWSD:package_name; or ZWSD:STAT=state; ZWSR; ZWSS:NAME=active_pckg_name; or ZWSS:STAT=; ZWSC:,:WDU,index:WO-BU; ZWQC:NAME=volume_name,DIRE=directory_name,STAT=FB;
ZIWX:,:F0,NODEF::%,%,; ZIWL:,:F0,NODEF::default_directory,FF,2,:; (FF for Default Directory) ZIWL:,:F0,NODEF:volume:directory_name,900,2,:; ( 900 for sub-directory) ZIWD:,:F0,NODEF:subdirectory:filename; ZIWM:,:F0,NODEF:directory:subdirectory:; ZIWY:S:SYSTEM=bsc,UNIT=OMU,PATH=/,DRIVE=FDU-N0; ZIWY:D:SYSTEM=bsc,UNIT=OMU,PATH=/root_dir/subdirectory,DRIVE=WDU-SB; ZIBC;
ZISI:,:WDU,drive#:; ZIBX:,,CTU,ctu:fileset_name,:; ZIBX:CTU,ctu,;
ZIWL: ZIWL: ZIWD:,:CTU-1,NODEF:subdirectory:filename; ZIWM:,:CTU-1,NODEF:directory:subdirectory:;
ZIWY:S:SYSTEM=bsc_name,UNIT=OMU,PATH=/,DRIVE=CTU-N1; ZIWY:D:SYSTEM=bsc_name,UNIT=OMU,PATH=/; ZIBC:,,,,,,,,,DIR:SSN=directory_name,SYSTEM=All,UNIT=ALL; SSN - Souce Set Name (Copying from tape)
DSN - Destination Set Name (Copying to tape)
ZIWX:,:WB,NODEF::%,%; ZIWX:,:WS,NODEF::%,%; ZIWX:,:WSB,NODEF::%,%; ZIWX:,:WS,NODEF:directory,:%,%:;
ZIWL:,:WSB,NODEF::default_directory,FF,2,:; (FF for Default Directory) ZIWL:,:WSB,NODEF:volume:directory_name,900,2,:; ( 900 for sub-directory) ZIWM ZIWD:,:WSB:NODEF:directory:file,file_extension; ZIWY:S:SYSTEM=bsc_name,UNIT=OMU,PATH=/; ZIWY:D:SYSTEM=bsc_name,UNIT=OMU,PATH=/,DRIVE=CTU-N1; ZIBC:,,,,,,,,,DIR:SSN=directory_name,SYSTEM=All,UNIT=ALL; ZDDS; MASHANGX.IMG ( Mass Memory Handling) PACKETGX.IMG (
ZDDS;
Backups
Link to RECOVERY PROCESS - Recovering from FallBack on Dat tape to Winchester Hard Drives **Com
Making a backup copy of the BSC software build to DAT tape.
Step 1 Make a fall back copy of the active package. This command will show you the packages that currently exist in your BSC. ZWQO:CR; Delete the oldest FB copy in the BSC with this command. ZWQD:NAME=fb_name:DIRE,PRINTS; MAFILE - when there is 1 active folder & 2 packages DIRE - U Create the new FB copy with this command. ZWKS:MODE=FULL,NAME=FBmmddyy,DIRE=FBmmddyy; Interrogate the status of the FB with this command. Once complete continue to step 2. ZWKI; Step 2 Recording to DAT tape. This command sets the destination. ZIWY:D:SYSTEM=fb_name,UNIT=OMU,PATH=/,DRIVE=CTU-N1; This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/FBmmddyy/BLCODE,DRIVE=WDU-S; This command copies to DAT. ZIBC:,,,,,,,,,DIR:DSN=BLCODE; This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/FBmmddyy/LFILES,DRIVE=WDU-S; This command copies to DAT. ZIBC:,,,,,,,,,DIR:DSN=LFILES; This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/FBmmddyy/MMDIRE,DRIVE=WDU-S; This command copies to DAT. ZIBC:,,,,,,,,,DIR:DSN=MMDIRE; This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/FBmmddyy/SCMANA,DRIVE=WDU-S; This command copies to DAT. ZIBC:,,,,,,,,,DIR:DSN=SCMANA; This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/FBmmddyy/ASWDIR,DRIVE=WDU-S; This command copies to DAT. ZIBC:,,,,,,,,,DIR:DSN=ASWDIR;
Shortcut for copying This command copies to dat the Directories BLCODE, LFILES, MMDIRE but does not copy SCMANA. SCMANA
ZIPS:"OMU",WDU-S,/FBweekly,,:"OMU",CTU-1,,,FBweekly:DIR=INC,ISD=Y:APP=ALL; This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/FBmmddyy/SCMANA,DRIVE=WDU-S; This command copies to DAT. ZIBC:,,,,,,,,,DIR:DSN=SCMANA; Step 3 Checking your work. This command sets the source. ZIWY:S:SYSTEM=fb_name,UNIT=OMU,PATH=/,DRIVE=CTU-N1; This command displays what you copied to DAT. ZIBX:CTU,1; Move commands ZWSS ZWSC ZWSD
Backup back to BSC
Link to recover from backup
SOMAFI COMMANDS
er Hard Drives **Complete System Fail**
2 packages DIRE - Used to delete package
SCMANA. SCMANA still needs to be copied over.
