Huawei NodeB Data Configuration

Internal

NodeB Data Configuration V100R007

HUAWEI TECHNOLOGIES CO., LTD.

www.huawei.com

All rights reserved

 Upon completion of this course, you

will be able to:

 Master data configuration procedure with CME  Master procedure of NodeB data configuration


All rights reserved

Page 2

References  《WRAN CME User Guide》

 《BTS3812E&BTS3812A Initial Configuration Guide》  《DBS3800 Initial Configuration Guide》


All rights reserved

Page 3

Chapter 1 Data Configuration Overview Chapter 2 Configuring Physical Equipment Chapter 3 Configuring Transport

Chapter 4 Configuring Local Cell Chapter 5 Configuring Operation and Maintenance Channel


All rights reserved

Page 4

Data Configuration Overview Configuration Tool CME


All rights reserved

Page 5

CME for Initial Configuration in Network Commissioning Cell Radio Parameter templates

Planned Radio data

NodeB Templates

Wizards of the task focused

CME Script is downloaded and activated

RNC

RNS

RNS

RNC

NodeB

NodeB

RAN  RAN Initial Data Configuration

 Configuring data based on the RAN network planning

 Exporting configuration data files  Loading the files to the RNC and NodeB through LMTs HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 6

CME for Data Modification in Network Expansion Cell Radio Parameter templates

Planned Radio data

Wizards of the task focused Upload

CME Script is downloaded and activated

RNS RNC

NodeB Templates

RNS RNC

NodeB

NodeB

RAN  RAN Data Modification  Adding/deleting/modifying a RNC WRBS  Adding/deleting/modifying a NodeB  Adding/deleting/modifying a cell  Modifying algorithm setting for RNO HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 7

Data Configuration Overview Procedure of NodeB Data Configuration

Configuring NodeB Data

Configuring Physical Equipment

Configuring Local cell

Configuring Transport

Physical equipment must be configured first


All rights reserved

Page 8




All rights reserved

Page 9

Configuring Physical Equipment Procedure of Physical Equipment Configuration Physical Equipment Configuration

USED FOR 3812E&A

Create NodeB

USED FOR DBS3800

Add HBBU

Add NMPT

Add HBBI Add HULP/HDLP

Add HBOI

Add NMON Add NAOI/NDTI NEMU/GPS

Add NCMU

Add MRRU

Add UL BB Resource Group Add MTRU/MAFU

Add NPMU

Add MRRU Chain/Ring

A

Add NPSU

Add Battery

Add NPMU For MRRU

End HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 10

A

Add NPMU for MBBU

Configuring Physical Equipment  Creating NodeB

− Adding NodeB basic data

▪ The basic data includes NodeB name and some basic NodeB data such as clock reference source, transmission line type, IP address, time zone, and demodulation mode  Note

− A NodeB name must be unique in one RNS


All rights reserved

Page 11

Configuring Physical Equipment—BTS3812E/A  Adding Boards to Baseband Subrack

 Adding boards to the baseband subrack

− The board can be NMPT,NMON,HBBI,HBOI,HULP,HDLP,NDTI or NAOI board  Note

− You must configure NMPT first, and configure HBBI before configuring MTRU and MAFU. NMPT, HBBI/HBOI and NDTI/NAOI (alternative) are mandatory

H H H H H H

H H H H

N

N

N N N

N

N

B B U U U U

U U D D

M

M

D A U

M

C

B B L

L L L

L

L L L

P

P

T O T

O

C

I

I

P P P

P P P P

T

T

I

I

N

U

0

1

12

13 14

P

2

3

4

5


6

7

8

9

10

11

All rights reserved

I

15

16

Page 12

17

Configuring Physical Equipment —BTS3812E/A  Adding Boards to RF Subrack

− Adding boards to the RF subrack. The board can be MTRU or MAFU board  Note − MTRU and MAFU have a one-to-one relationship − You must add HBBI first before you are adding MTRU and MAFU

MAFU0

MAFU1

MAFU2

MAFU3

MAFU4

MAFU5

MTRU0

MTRU1

MTRU2

MTRU3

MTRU4

MTRU5


All rights reserved

Page 13

Configuring Physical Equipment —BTS3812E/A  Adding UL Baseband Resource Group

− Adding a UL baseband resource group and UL process units  Note − Each UL baseband resource group administrates up to six cells − Cells in the same frequency band shall be assigned in the same UL baseband resource group

H H H H H H

H H H H

N

N

N N N

N

N

B B U U U U

U U D D

M

M

D A U

M

C

B B L

L L L

L

L L L

P

P

T O T

O

C

I

I

P P P

P P P P

T

T

I

I

I

N

U

0

1

12

13 14

P

2

3

4

5


6

7

8

9

10

11

All rights reserved

15

Page 14

16

17

Configuring Physical Equipment —BTS3812E/A  Adding NPMU (only for BTS3812A)

−

Adding an NPMU and its PSU and batteries

 Adding NCMU (only for BTS3812A)

−

The NCMU is the temperature control unit of the

BTS3812A.  Configuring NEMU (only for BTS3812E)

−


The NEMU is a peripheral of the NodeB

All rights reserved

Page 15

Configuring Physical Equipment ----DBS3800

 Adding HBBU

− Adding an HBBU  Note

− You can add only one HBBU to a NodeB


All rights reserved

Page 16

Configuring Physical Equipment —DBS3800 Adding MRRU Chain/Ring

− Adding an MRRU chain or ring Chain

Note − The MRRU chain or ring is configured to the HBBU/HBOI CPRI ports

Ring

− Each HBBU/HBOI has three CPRI ports

Star

− The MRRU chain occupies one CPRI port, and the MRRU ring occupies two CPRI ports Adding MRRU

Note − For the data configuration of a distributed NodeB, each MRRU is considered as a subrack. The subrack number of an MRRU must be unique within the distributed NodeB system HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 17

Configuring Physical Equiment  Configuring GPS Receiver

− GPS receiver is a peripheral of the NodeB

Antenna

− It is used to locate UE Bracket

 Adding TMA

Jumper

− Adding a TMA TMA

Jumper

 Adding RET

− Adding a RET Feeder Jumper NodeB Cabinet


All rights reserved

Page 18




All rights reserved

Page 19

Chapter 3 Configuring Transport Sector 1 Configuring Transport over ATM Sector 2 Configuring Transport over IP


All rights reserved

Page 20

Configuring Transport over ATM Iub Interface protocol over ATM

NBAP NCP

Transport Network Layer

RACH FP

Radio Network Layer

CCP

FACH FP

User plane

Control Plane

CCP

Transport Network User Plane

Transport Network Control Plane


ALCAP

A SAAL UNI

C

B SAAL UNI

AAL2 PATH

ATM Physical Layer


All rights reserved

Page 21

Configuring Transport over ATM Iub Interface protocol Control Plane

NodeB

CCP 1~n NCP

User Plane

AAL2 PATH

NodeB

VBR-RT VBR-NRT

Iub data

AAL2Path

Adjnode

segmentation packing

AAL1

RNC

NCP or CCP or ALCAP or IPoA

CES

CBR

ALCAP

AAL2

AAL5

IMA/UNI/STM-1 VCI-101

VPI-10 VPI-10

ATM Cell

VCI-100 VCI-100

E1/T1/SDH(STM-1)

VCI-101

VPI-20 AAL Layer

ATM Layer


Physical Layer

All rights reserved

Page 22

RNC

Configuring Transport over ATM Procedure of Transport Configuration

Transport Configuration

Create NodeB

Add NAOI

Add NDTI/HBBU

Add IMA Group

Add Fractional ATM

Add UNI LINK

Add Time Slot Across

Add IMA Link

Add ALCAP

Add NCP/CCP/ IPoA Device

Add Treelink PVC

Add AAL2 Path

End HUAWEI TECHNOLOGIES CO., LTD.

Add STM-1 Link

All rights reserved

Page 23

Add CES (only3812E&A)

Configuring Transport over ATM  Configuring Physical Links at Transport Layer

− Adding the physical links to the NodeB for data transmission over Iub interface  Note

− An E1/T1 port can be configured to any of the following links for data transmission: ▪ UNI link ▪ Fractional ATM link ▪ IMA link ▪ CES link − An optical port can be configured to any of the following links for data transmission: ▪ STM-1 link HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 24

Configuring Transport over ATM  Physical Links Configuration

 Physical ports(BTS3812E&A) Board type

Port number

Work mode IMA,UNI,

E1/T1 port No.0

CES, Fractional ATM, Timeslot cross (connect with RNC)

E1/T1 port No.1 NDTI

IMA,UNI, CES, Fractional ATM

E1/T1 port No.2~3

IMA, UNI, Timeslot cross

(connect with lower level NodeB)

NAOI

E1/T1 port No.4~7

IMA,UNI

E1/T1 port No.0~3

CES

Optical port No.0~1

STM-1


All rights reserved

Page 25


 Physical ports(DBS3800) Board type

Port number

Work mode IMA,UNI,

E1/T1 port No.0

Fractional ATM, Timeslot cross (connect with RNC)

E1/T1 port No.1

IMA,UNI, Fractional ATM

HBBU E1/T1 port No.2~3

IMA, UNI,

Timeslot cross (connect with lower level NodeB)

E1/T1 port No.4~7


All rights reserved

IMA,UNI

Page 26


 Add an UNI link Header ATM cell

53 octets

ATM cell mapping field: 30 octets (TS1 - TS15 and TS17 - TS31) Header Header Header Header TS0 provides F3 OAM functions: Performance monitoring (CRC-4) Transmission of FERF and LOC Performance reporting Detection of loss of frame alignment

TS16: Reserved for signaling

256 bits/125 ls


All rights reserved

Page 27

Configuring Transport over ATM  Physical Links

Configuration  Add an IMA Group IMA group PHY

IMA group

Physical I ink #0 PHY


PHY

Original ATM cell stream µ¥ATMÐÅÔªÁ÷ from ATM layer

Recovered ATM cell stream to ATM layer


PHY

IMA virtual link


All rights reserved

Page 28


 Add an IMA link to an IMA group − IMA Link No. : defines the E1/T1 No. on the NDTI/HBBU IMA Frame 2

IMA Frame 1

... ATM

m-1

... ATM ATM

...

F

3

F

ICP2

2

1

0

ICP2 ATM

F

F

...

F

F

m-1

...

ATM

3

2

F

1

ICP1 ATM

0

m-1

... ATM ATM ICP2

F

ATM

Link 0 F ATM

3

...

ICP1 ATM ATM ATM ATM

ATM

... F

IMA Frame 0

2

ICP0 ATM

Filler cell

F


ATM

1 F

ICP0

0 F

... ATM ICP1 ATM ATM

ATM layer cell

ATM ICP0 ATM

ICP2 ICP cell in frame #2

All rights reserved

Link1

Link2

F

Time F

F

Page 29


 Adding a Fractional ATM Link − Bearing port No. : defines the E1/T1 No. on the NDTI ATM cell carrying Fractional ATM link NDTI E1 0/1 3G data

Fractional E1 slots available for ATM cell, others may be used by 2G BTS

BTS38XX NDTI

RNC Iub interface board Transport other information rather than ATM cell


All rights reserved

Page 30


 Adding a Timeslot Across Channel − Add the corresponding Fractional ATM link on NDTI/HBBU E1/T1 0 first ATM cell carrying 3G data Fractional ATM Link

Fractional E1/T1timeslots are used by Fractional ATM; other timeslots are used by timeslot across channel

NDTI No.0 E1/T1

BTS38XX NDTI

RNC Iub interface board Timeslot across channel

2G BTS data

timeslots available on NDTI No.2/3 E1/T1


2G BSC data

All rights reserved

Page 31


 Adding a CES Channel

− If NDTI is used, NDTI No.0/1 E1 is directly connected to 2G BTS − If NAOI is used, NAOI E1/T1 is directly connected to 2G BTS 3G data packed into ATM cell

E1/T1 timeslot data packed into ATM cell

E1/T1 timeslot data restored from ATM cell

ATM cell transport

BTS38XX NDTI/NAOI

RNC Iub interface board

E1/T1, some timeslots available

E1/T1, some timeslots available CES channel 2G BSC data

2G BTS data


All rights reserved

Page 32

Configuring Transport over ATM  Adding NCP

− Adding the NCP to the Iub interface

 Note − Only one NCP is configured to the NodeB

− Negotiated with the peer end RNC ▪ VPI and VCI of NCP ▪ Traffic over the NCP includes: Service type, Peak cell rate , Sustain cell rate


All rights reserved

Page 33

Configuring Transport over ATM  Adding CCP

− Adding a CCP to the Iub interface  Note

− One NodeB supports multiple CCPs − Negotiated with the peer end RNC ▪ CCP No. ▪ VPI and VCI of CCP ▪ Traffic over the CCP includes: Service type, Peak cell rate , Sustain cell rate


All rights reserved

Page 34

Configuring Transport over ATM  Adding ALCAP Node and link

− Adding the ALCAP node to the NodeB and an ALCAP link to the Iub interface  Note − One NodeB is configured with only one ALCAP link

− Negotiated with the peer end RNC ▪ ATM address of NodeB

▪ VPI and VCI of the ALCAP link ▪ Traffic over the ALCAP link includes :Service type, Peak cell rate , Sustain cell rate


All rights reserved

Page 35

Configuring Transport over ATM  Adding AAL2 Path

− Adding an AAL2 path to the Iub interface  Note − One NodeB may have multiple AAL2 paths − The number of paths can be calculated based on the traffic model over the Iub interface

− Negotiated with the peer end RNC ▪ AAL2 path ID

▪ VPI and VCI of the AAL2 path ▪ Traffic over the AAL2 path includes :Service type, Peak cell rate , Sustain cell rate


All rights reserved

Page 36

Configuring Transport over ATM  Adding Treelink PVC

− Adding a Treelink PVC to the lower level NodeB ▪ The Treelink PVC enables the NodeB to connect with its upper level node and lower level NodeB through different E1/T1 ports  Note − Optional for NodeB initial configuration

− Add Treelink PVCs to all the upper level NodeBs when the NodeB is cascaded with the other NodeBs − Negotiated with the lower level NodeB ▪ PVC to lower level NodeB − Negotiated with the upper level NodeB ▪ PVC to upper level NodeB


All rights reserved

Page 37

Configuring Transport over ATM Architecture of Treelink PVC AAL layer and higher layer

ATM physical layer bearer Transport Physical medium

AA RNC

E1/T1 or Optical fiber


TREELINK PVC

ATM layer (PVC)

ATM layer PVC


D BTS38XX(A)

A E1/T1 or Optical fiber

All rights reserved

Page 38

BTS38XX(B)

Configuring Transport over ATM VPI Planning for VP-only Switching Treelink PVC AAL layer and the higher layer

TREELINK PVC

ATM layer (PVC)



A

D

AA RNC

ATM layer PVC

E1/T1 or Optic fiber

BTS38XX (A)

VPI range: (6, 6)


E1/T1 or Optic fiber

BTS38XX (B)

VPI range: (7, 7)

All rights reserved

BTS38XX (C)

VPI range: (8, 8)

Page 39

Chapter 3 Configuring Transport Sector 1 Configuring Transport over ATM Sector 2 Configuring Transport over IP


All rights reserved

Page 40

Configuring Transport over IP Iub interface protocol over IP

NCP

Transport Network Layer

CCP

CCP



SCTP

UDP

IP

IP

Data Link Layer

Data Link Layer

A

C

Physical Layer


CPCH FP

NBAP

FACH FP

RACH FP

Radio Network Layer

USCH FP

User Plane

Control Plane

All rights reserved

Page 41

Configuring Transport over IP Start

Configure the PPP

Configure the PPPoE

Configure the MP

Configure the Ethernet IP

Configure the IP Route Configure the QoS NodeB (optional) Configure the NBAP 配置IP Route Configure the OM 配置IP Route Configure the IP path

End


All rights reserved

Page 42

Configuring Transport over IP  Configure the PPP, MP, PPPoE, and Ethernet IP

− In a single transport mode, configure one type of transport links. − In hybrid transport mode, configure E1 and FE transport links. ▪ For E1 links, configure PPP or MP. ▪ For FE links, configure PPPoE or Ethernet IP. PDH/SDH

NodeB

RNC

IP network

IP hybrid transmission


All rights reserved

Page 43

Configuring Transport over IP  Configure the IP route

 If the gateway type of the route is Ethernet, the next hop address and the gateway IP address must be in the same network segment  If the NodeB and RNC are in layer 2 networking

− The IP addresses of the FE ports on the NodeB and RNC should be in the same subnet  If the NodeB and RNC are in layer 3 networking − The next hop address is the IP address of the router that connects to the NodeB or the IP address of the port on a layer 3 switch.

 The destination address of packets has the corresponding route in the routing table.  The corresponding link layer address can be found only when the router specifies the next hop IP address (gateway).  Configure just one route to the same destination address. HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 44

Configuring Transport over IP  Configure the QoS

 To configure signaling and OM priorities  IP Quality of Service (QoS) is an IP network capability to provide specific services over the IP network that uses mutiple bottom-layer network technologies such as MP, FR, ATM, Ethernet, SDH, and MPLS  IP QoS supports the switching between the IP precedence and DSCP  The IP QoS configuration is flexible


All rights reserved

Page 45

Configuring Transport over IP  Configure the NBAP

 Configure destination IP address & local IP interface, port type and port number  The IP routes for destination addresses are available  Only one NCP can be configured

 Several CCPs can be configured  The destination IP address, local port number, and destination port number of the NCP/CCP on the same link should be different  When you choose one NCP/CCP on the NBAP tab page, the corresponding links are displayed in the middle part, and the corresponding routes are displayed in the lower part


All rights reserved

Page 46

Configuring Transport Based on IP  Configure the OM

 Ensure that the route from the LMT (or M2000) to the subnet is configured  Only one OM channel can be configured  If you choose an OM channel in the upper part of the OM tab page, the corresponding route is displayed in the lower part  The destination IP address of the OM channel is the IP address of the NodeB LMT or M2000


All rights reserved

Page 47

Configuring Transport over IP  Configure the IP path

 The IP routes for destination addresses are available

 The IP path does not have bandwidth limit. Therefore, to configure the IP path is to differentiate service priorities. When the HSDPA service is transmitted, configure two IP paths with different path IDs. The two paths correspond to R99 service and HSDPA service. There is no service priority at the NodeB side. Therefore, configure one IP path at the NodeB side  If you choose one path on the upper part of the IP path tab page, the corresponding links are displayed in the middle part and the corresponding route is displayed in the lower part


All rights reserved

Page 48

Chapter 1 Data Configuration Overview Chapter 2 Configuring Physical Equiment Chapter 3 Configuring Transport



All rights reserved

Page 49

Configuring Local Cell Procedure of Local Cell Configuration

Locall cell

Add Site


Add Local Cell

Add Sector

All rights reserved

Page 50

Configuring Local Cell 

Adding Site − Adding a site to the NodeB

 Note − A site number within one

NodeB must be unique.

 Adding Sector

− Adding a sector to the NodeB  Note − A sector number must be unique within one NodeB − Configuring a sector is mainly configuring the corresponding antenna and feeder system HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

Page 51

Configuring Local Cell 

Adding Local Cell

− Adding a local cell to the NodeB  Note − Local Cell ID must be unique within the same NodeB − Negotiated with the peer end RNC ▪ Local Cell ID ▪ Uplink Frequency

▪ Downlink Frequency


All rights reserved

Page 52

Chapter 1 Data Configuration Overview Chapter 2 Configuring Physical Equiment Chapter 3 Configuring Transport



All rights reserved

Page 53

Configuring Operation and Maintenance Channel  NodeB provides two modes of operation and

maintenance:  Near end operation and maintenance:  Far end operation and maintenance: IPoA Peer IP

NMPT Ethernet Port IP address

Subnet 4 RNC BAM IP

IPoA local IP SNTP Server Subnet 1

Subnet 3

Subnet 2

Subnet 5

RNC M2000

BTS3812E LMT1

LMT 2


All rights reserved

Page 54

Operation and Maintenance Channel Configuration IPoA maintenance configuration The route to LMT (IP4), SNTP Server, gateway: IP2

BTS3812E NMPT ETH IP

(A) (B)

Configure IPoA local IP: IP1

IP0

Lower level Node B

IP1

Configure IPoA local IP: IP6

IP: IP4

LocalBTS3812E IP5

(B) Configure networking PVC


(D) Configure the route to BTS3812E (IP1), gateway:IP3

IP2

IP3

IP6

The route to LMT(IP4) gateway:IP5

(C) Configure LMT Ethernet

IPoA peer IP: IP2

IP4 LMT

RNC

IPoA peer IP:IP5

All rights reserved

Configure the route to lower NodeB (IP6), gateway:IP3

Page 55

Configuring Operation and Maintenance Channel  Adding IPoA Device

− Configuring an IPoA maintenance channel to the NodeB ▪ Through the IPoA maintenance channel, you may log in to the NodeB remotely with the LMT or the M2000

 Note − You can add only one IPoA maintenance channel to a NodeB − Negotiated with the peer end RNC

▪ Local IP and Local IP Mask ▪ Peer IP and Peer IP Mask

▪ VPI/VCI ▪ Service Type


All rights reserved

Page 56

Thank You www.huawei.com

Huawei NodeB Data Configuration

Recommend Documents