Oil + Air-Lubrication System for lubrication of spindles, linear guides, rack pinions, chains and assembly processes Product line:
Owner’s Manual - Containing Installation, Operation and Maintenance Instructions (Original installation instructions in accordance with ECMachinery Directive 2006/42/EC) 2006/42/EC)
Version 01
OLAxx-…
WARNING: Read this owner's manual before installing, operating or maintaining the product. Failure to follow the instructions and safety precautions in this owner’s manual could result in serious injury, death, or property damage. Keep for future reference.
blank page
blank page
Masthead
page 3
Masthead
Service
This owner’s manual - containing installation, operation and maintenance instructions complies with EC-Machinery Directive 2006/42/EC and is an integral part of the described product. It must be kept for future use.
If you have technical queries, please contact one of the following plants:
This owner’s manual - containing installation, operation and maintenance instructions was created in accordance with the valid standards and regulations on documentation, VDI 4500 and EN 292. © SKF Lubrication Systems Germany AG This documentation is protected by copyright. The photomechanical reproduction, copying, and distribution of this documentation or parts thereof by means of processes such as data processing, data carriers, and data networks is strictly prohibited without the express permission of SKF Lubrication Systems Germany AG. SKF Lubrication Systems Germany AG reserves the right to make content and technical changes.
SKF Lubrication Systems Germany AG Plant Berlin Motzener Straße 35/37 12277 Berlin Germany Tel. +49 (0)30 72002-0 Fax +49 (0)30 72002-111 Plant Hockenheim 2. Industriestraße 4 68766 Hockenheim Germany Tel. +49 (0)62 05 27-0 Fax +49 (0)62 05 27-101
[email protected] www.skf.com/schmierung
EN
Table of contents
page 4
EN
Table of contents Owner’s Manual - Containing Installation, Operation and Maintenance Instructions (Original installation instructions in accordance with EC-Machinery Directive 2006/42/EC) Masthead 3 Service 3 Table of contents 4 Information concerning the EC Declaration of Conformity and the EC Declaration of Incorporation 5 Safety information in owner’s manual 6 Meaning of symbols and corresponding information 6 1. Safety information 7 1.1 Intended use 7 1.2 Authorized personnel 7 1.3 Danger relating to electric current 8 1.4 Danger relating to system pressure 8 1.5 Danger relating to compressed air 8 1.6 Warranty and liability 8 2. Lubricants 9 2.1 General information 9 2.2 Selection of lubricants 9 2.3 Approved lubricants 10 2.4 Lubricants and the environment 10 2.5 Danger relating to lubricants 11
3. Design and function 12 3.1 General information 12 3.2 Principle of oil + air lubrication 12 3.3 Fields of application 12 3.4 Design 13 3.5 Description of components 14 3.6 Function 20 3.7 Models and designations 21 4. Installation instructions 22 4.1 Positioning and mounting 22 4.2 Mounting dimensions 23 4.3 Electrical connection 23 4.3.1 Electrical connection motor 23 4.3.2 Inductive loads 24 4.4 Control and monitoring 25 4.4.1 Oil + air lubrication systems without control unit 25 4.4.2 Oil + air lubrication systems with control unit 26 4.5 Compressed air line connection 27 4.6 Lubrication line connection 28 4.7 General information about laying of lubrication line 30
5. Transport, delivery and storage 5.1 Transport 5.2 Delivery 5.3 Storage 5.3.1 Storage of lubrication units 5.3.2 Storage of electronic and electrical devices 5.3.3 Storage - general information 6. Operation 6.1 General information 6.2 Commissioning 6.2.1 Setting-up mode 6.3 Lubricant delivery to bearing 6.4 Setting the lubricant flow rate 6.5 Setting the air flow rate 6.6 General notes 7. Shutdown 7.1 Temporary shutdown 7.2 Permanent shutdown 8. Maintenance 9. Faults 10. Technical data 10. Technical data (cont.)
31 31 31 31 31 31 31 32 32 32 33 33 36 39 40 41 41 41 42 43 45 46
Information concerning the EC Declaration of Conformity and the EC Declaration of Incorporation
page 5
EN
Information concerning the EC Declaration of Conformity and the EC Declaration of Incorporation For the product(s) designated below: Oil-Air Lubrication System
(d) Operation of the products on non-standard main voltage as well as nonobservance of installation instructions can affect the EMC properties and electrical safety.
Product line: OLAxx-… SKF herewith certifies that it conforms to the pertinent safety requirements set forth in the following Council Directive(s) for the harmonisation of the laws of the Member States... ) ) )
SKF further declares that the above mentioned product: )
Machinery Directive 2006/42/EC Low-voltage Directive 2006/95/EC Electromagnetic compatibility 2004/108/EC
Notes: (a) This declaration certifies conformity with the aforementioned directive(s), but does not contain any assurance of properties. (b) The safety instructions in the owner’s manual must be observed. (c) The certified product must not be started up until it is confirmed that the equipment, machinery, vehicle or the like in which the product was installed meets the provisions and requirements of the national directives to be applied. This is in particular important for the implementation of the Use of Work Directive.
)
is meant for integration into a machinery / for connection to other machinery according to the EC-Machinery Directive 2006/42/EC, Appendix II Part B. Starting up the product is not permissible until it is assured that the machinery, vehicle or the like in which the product was installed meets the provisions and requirements of the regulations set forth in the EC Directive 2006/42/EC. with reference to the EC Directive 97/23/EC concerning apparatus subjected to pressure, this product must only be used as intended and according to the Owner’s manual. Especially observe the following: Products of SKF Lubrication Systems Germany AG must not be used in conjunction with fluids, group I (hazardous fluids), according to the definition of article 2 paragraph 2 of the Directive 67/548/EC dtd. 27th June, 1967; and are not approved for application with such fluids.
None of the products manufactured by SKF Lubrication Systems Germany AG can be used with gases, liquefied gases, gases dissolved under pressure, steams or fluids that will reach a steam pressure of more than 0.5 bar above the normal atmospheric pressure (1013 mbar) in the permissible application temperature range. When used as intended, the products supplied by SKF Lubrication Systems Germany AG do not reach the limit values listed in the Article 3 par. 1, sections 1.1 to 1.3 and par. 2 of the Directive 97/23/EC. Therefore, they do not come under the requirements set forth in annex I of that Directive. They are not labelled with the CE mark with reference to the Directive 97/23/EC. They are classified by SKF Lubrication Systems Germany AG to come under Article 3 par. 3 of the Directive. The EC Declaration of Conformity and EC-Declaration of Incorporation is part of the product documentation. These documents are delivered with the product.
Safety information in owner’s manual
page 6
EN
Safety information in owner’s manual Meaning of symbols and corresponding information In this owner’s manual, the symbols and words shown on this page are meant to communicate a particular risk to persons, material assets, or the environment. Be sure all persons exposed to these risks read this manual. Keep it near the equipment for future reference. Hazard symbols Symbole
Instructions attached directly to the equipment, such as rotational direction arrows and fluid connection labes, must be followed. Replace such signs if they become illegible. ) )
Rotational direction arrow Fluid connection label
Note: Not every symbol and corresponding information described in the Safety Information is used in this owner’s manual. Keywords in safety informations and their meanings
Standard
Use
DIN 48442 W000
General risk of injury or damage
DIN 48442 W008
Keyword
Use
Danger!
Indicates a danger of injury to persons
Caution!
Voltage Notice!
DIN 48442 W026
Hot surface
DIN 48442 W028
Slip hazard
Read this Owner's Manual before installing, operating or maintaining the product. Failure to follow the instructions and safety precautions in this owner’s manual could result in serious injury, death, or property damage. Keep for future reference.
Indicates a danger of damage to property or the environment Indicates additional
Information symbols Symbol
Use Prompts you to take action
)
Indicates other issues, causes or circumstances Used for bulleted lists Provides additional information Prompts you to take action
1. Safety information
1. Safety information These instructions must be read and understood by all persons who are involved with the installation, operation, maintenance, and repair of the product. These instructions must be kept close to the equipment for future reference. Note that these installation instructions is an integral part of the product. It must be handed over to the new operator of the product if the product is sold. The described product was manufactured in accordance with all generally acknowledged regulations pertaining to technology, occupational safety, and accident prevention. However, dangers that can cause physical injury to persons or damage to other material assets might still occur during the use of the product. This product should only be operated if it has been installed in accordance with these instructions and is safe to operate. In particular, malfunctions that might affect the safety of the product must be rectified immediately. In addition to the information provided in the installation instructions, all generally applicable regulations on accident prevention and the environment must be observed.
page 7
1.1 Intended use All SKF Lubrication Systems Germany AG products must only be used for their intended purpose and in accordance with the specifications of the installation instructions for the product in question. The described product is for supplying centralized lubrication systems with lubricant and is intended for use in centralized lubrication systems. Any other use of this product constitutes improper use. Products of SKF Lubrication Systems Germany AG must not be used in conjunction with fluids, group I (hazardous fluids), according to the definition of article 2 paragraph 2 of the Directive 67/548/EC dtd. 27th June, 1967; and are not approved for application with such fluids. None of the products manufactured by SKF Lubrication Systems Germany AG can be used with gases, liquefied gases, gases dissolved under pressure, steams or fluids that will reach a steam pressure of more than 0.5 bar above the normal atmospheric pressure (1013 mbar) in the permissible application temperature range. Unless otherwise noted, products of SKF Lubrication Systems Germany AG must not be used in conjunction with explosive atmospheres according to the ATEX-Directice 94/9/EC.
EN
1.2 Authorized personnel The products described in the installation instructions may only be installed, operated, maintained, and repaired by qualified experts. Qualified experts are persons who have been trained, instructed, and familiarized with the end product into which the described product is installed. These persons are considered capable of such tasks due to their education, training, and experience with valid standards, conditions, accident prevention regulations, and installation measures. They should be able to carry out the required tasks and to recognize - and thus avoid - any dangers that might otherwise occur. A definition of what constitutes a qualified person and who are unqualified persons are stipulated in DIN VDE 0105 and IEC 364.
1. Safety information
1.3 Danger relating to electric current The electrical connection for the described product may only be established by qualified, instructed persons who have been authorized by the operator or owner to carry out this task. All local electrical operating conditions and regulations such as DIN and VDE must be observed. Improperly connected products can result in considerable damage to property and serious injury to persons. Danger! Working on products that have not been disconnected from the power supply can cause serious injury or death to persons. Installation, maintenance, and repair work may only be carried out by qualified experts on products that have been disconnected from the power supply. The supply voltage must be turned off before any product components are opened.
page 8
1.4 Danger relating to system pressure Danger! Centralized lubrication systems are under pressure when they are being operated. Such systems must therefore be depressurized before starting installation, maintenance, or repair work and before making any changes to the system.
1.5 Danger relating to compressed air Danger! The described product may be under pressure when it is being operated. The product must therefore be depressurized before starting installation, maintenance, or repair work and before making any changes to the system. The oil+air metering units are operated with compressed air.
EN
1.6 Warranty and liability SKF Lubrication Systems Germany AG assumes no warranty and liability if one of the following circumstance should occur: ) )
)
)
)
)
)
Not intended use Improper installation/disassembly or improper operation of the product Use of contaminated lubricants or lubricants which are not approved Improper maintenance or repairing of the product Using of unoriginal SKF Lubrication Systems Germany AG spare parts Making alterations or modifications to the product, which are not approved and signed by SKF Lubrication Systems Germany AG Non-observance of the advices about transport and storage
2. Lubricants
2. Lubricants 2.1 General information All SKF Lubrication Systems Germany AG products must only be used for their intended purpose and in accordance with the specifications of the installation instructions for the product in question. The intended use of this product is for the centralized lubrication/lubrication of bearings and wear points with lubricants. All physical limitations of use stipulated in the documentation of the product such as the owner’s manual, technical drawings and catalogues must be observed. Note that hazardous substances of any kind and in particular - the substances that are classed as hazardous in accordance with EC-Directive 67/548/EC Article 2, Paragraph 2 may only be inserted into and conveyed/distributed by centralized lubrication systems and components following consultation with SKF Lubrication Systems Germany AG and with the express written permission of the company. Products manufactured by SKF Lubrication Systems Germany AG are not approved for use in conjunction with gases, liquefied gases, gases dissolved under pressure, vapours, and fluids with a vapour pressure of more than 0.5 bar above normal atmospheric pressure (1013 mbar) at the maximum permitted temperature.
page 9 Should there be a need to use the product to convey media other than lubricants or hazardous substances, this must be discussed with SKF Lubrication Systems Germany AG first and the company must give express written permission. In the opinion of SKF Lubrication Systems Germany AG, lubricants constitute a design element that must be considered when selecting components and designing centralized lubrication systems. The lubrication properties of the lubricants in question must be considered.
2.2 Selection of lubricants You must observe the machinery manufacturer's information on the lubricants to be used in the machinery. Caution! The manufacturer of the bearing or machinery to be lubricated will specify the lubricant requirements for each point to be lubricated. You must make sure that the required quantity of lubricant is provided to the relevant lubricating point. If a lubricating point is insufficiently lubricated, the bearing may become damaged or jammed.
EN
While the machinery/bearing manufacturer usually specifies lubricants, it is the owner/operator (or maintenance person) who must finally select the appropriate lubricant, with the help of the lubricant supplier. When selecting a lubricant, the type of bearing/wear point, the stresses and strains to be expected during operation, and anticipated ambient conditions must be taken into account. All financial/economic aspects must also be considered. If required, SKF Lubrication Systems Germany AG can help customers to select suitable components for the conveyance of the selected lubricant and to plan and design their centralized lubrication system. If you have further questions, you can contact SKF Lubrication Systems Germany AG. We can test lubricants in our own laboratory to establish their suitability for conveyance (e.g. 'oil separation' behaviour) in centralized lubrication systems. You can request an overview of lubricant tests offered by SKF Lubrication Systems Germany AG from our Service department.
2. Lubricants
2.3 Approved lubricants Caution! Only lubricants that have been approved by SKF for use with the product may be used. Unsuitable lubricants can cause product malfunctions and damage to property. Caution! Different lubricants must not be mixed together. Doing so can cause damage and require extensive cleaning of the products/centralized lubrication system. To prevent confusion, we recommend that you attach information indicating the lubricant to be used on the lubricant reservoir. The described product can be operated with lubricants that comply with the specifications in the technical data. Note that some lubricants may have properties that lie within the permitted limit values and yet not be suitable for use in centralized lubrication systems for other reasons. For example, some synthetic lubricants are not compatible with elastomers.
page 10 Oils with a viscosity lower than shown in Table 1 should be avoided, as their load-carrying capacity may not be sufficient at high bearing loads, which may reduce bearing service life. Oils with solid additives cannot be used, as such oils may leave solid particle sediment within the oil circuit and thereby block the circuit's function. There is also a risk of solid particles creating a coating that critically reduces the bearing clearance. Table 1: Permitted oils Requirement Recommended oil purity class Recommended ISO VG grade Permitted additives Non-permitted additives
Values 13/10 (ISO 4406) or Class 4 (NAS 1638) 32 to 100 based on 40 °C EP additives Solids
EN
2.4 Lubricants and the environment Caution! Lubricants can contaminate the ground and watercourses. Lubricants must be used and disposed of properly. Country specific regulations and laws on the use and disposal of lubricants must be observed. Note that lubricants are harmful to the environment and flammable; their transportation, storage, and processing are subject to special precautionary measures. For specifications on transportation, storage, processing, and dangers to the use and the environment for the lubricant, refer to the material safety data sheet provided by or available from the lubricant manufacturer. You can ask the manufacturer of the lubricant for the material safety data sheet.
2. Lubricants
2.5 Danger relating to lubricants Danger! Centralized lubrication systems must be leak-tight. Leaking centralized lubrication systems can cause a slip hazard. When performing installation, maintenance, and repairs test the centralized lubrication system for leaks. Leaky parts of the centralized lubrication system or components of the lubrication equipment have to be sealed immediately. Leaking centralized lubrication systems or components of the lubrication equipment are a source of danger in relation to slip hazard and the risk of injury. These dangers can cause physical injury to persons or damage to other material assets. Lubricants are hazardous substance. Refer to safety precautions in the lubricant manufacturer's material safety data sheet. You can ask the manufacturer of the lubricant for the material safety data sheet.
page 11
EN
3. Design and function
3. Design and function 3.1 General information Oil + air lubrication systems are total-loss oil lubrication systems which are used in centralized lubrication to provide minimal quantity metering of oils. Oil + air lubrication systems are employed in a wide range of applications. Typical fields of application for oil + air lubrication systems are: ) ) ) ) )
)
Rolling bearing lubrication Linear guide lubrication Chain lubrication Rack and pinion lubrication Lubrication for cutting and non-cutting shaping Installation and process oiling
page 12
EN
3.2 Principle of oil + air lubrication
3.3 Fields of application
In oil + air lubrication, a continuous stream of air (compressed air) separates a volumetrically metered quantity of oil into a streak in a lubrication line and transports it along the pipe wall to the lubrication point. Metering can be performed by piston distributor, injection oiler, micropump, an oil + air metering unit, etc.
Oil + air lubrication systems provide a continuous, finely metered flow of oil which can be tailored to different operating conditions by selecting the metered quantity, setting the velocity of compressed air stream and changing the lubricating cycle sequence. An excellent use of oil + air lubrication is the lubrication of high-speed rolling bearings, for example in spindles for machine tools. Other applications include the lubrication of highspeed transport chain conveyors that do not support intermittent lubricant feeding due to their high rotating speed. In production processes for textile fibers, an oil + air lubrication system can be used to apply minimal quantities of lubricant (gripper lubrication).
The volumetrically metered quantity of oil is fed into the air stream in bursts and is transported by the air stream to the attached lubrication point line. A nearly continuous oil flow is generated by a lubrication point line that is at least 1 m long between the metering device and the entrance to the lubrication point. This oil flow exits the lubrication point line as fine oil droplets and is fed to the lubrication point. The oil droplets fed to the lubrication point lubricate the friction partners, while the compressed air is discharged into the surroundings nearly free of oil.
3. Design and function
3.4 Design An oil + air lubrication system can be subdivided into areas for oil supply/oil metering and compressed air supply. The oil can be metered and the compressed air admixed either by an oil + air metering unit (oil is metered and compressed air is admixed in one component) or using separate mixing valves that are combined with piston distributors, injection oilers or micropumps (oil is metered and the compressed air is admixed in separate components). The basic design of an oil + air lubrication system consists of the following components (Fig. 1): )
)
Compact unit with or without control unit (Fig. 1 shows compact unit without control unit) and with gear pump (1), lubricant reservoir (2), the valve set required for pressure relief and regulation, a pressure switch for electrical monitoring of oil pressure build-up, a pressure gauge (4) for visual monitoring of oil pressure build-up, and a fill level switch for fill level monitoring. Pressure control valve with pressure gauge (6) for compressed air control
page 13 )
Pressure switch (8) for monitoring of minimum air pressure
)
Oil + air metering unit (9) for metering oil and admixing compressed air
The components in the basic design are arranged on a mounting plate and supplied as a complete oil + air lubrication system. If necessary, additional components can optionally be integrated into the oil + air lubrication system, for example: )
)
)
)
)
Oil filters (with or without electrical contamination monitoring) Air filters (with or without electrical contamination monitoring) Additional pressure switches for lubricant and compressed air monitoring Flow sensors for monitoring lubricant transport in lubrication lines Flow sensors for monitoring lubricant transport (oil streak) in lubrication point lines
EN
For detailed information about the components installed in a special oil + air lubrication system, see the documentation of the oil + air lubrication system. If no documentation is available, you can request the documentation directly from SKF Lubrication Systems Germany AG.
3. Design and function
3.5 Description of components Figure 1 shows an oil + air lubrication system; Figures 2 and 3 show the various oil + air metering units. Figure 4 shows the hydraulic diagram of an oil + air lubrication system. Compact unit without control unit (1) The compact unit without control unit (1) consists of a gear pump, lubricant reservoir (2), the valve set required for pressure relief and regulation, a pressure switch for electrical monitoring of oil pressure build-up in the main lubricant line, a pressure gauge (4) for visual monitoring of oil pressure build-up in the main lubricant line, and a fill level switch for fill level monitoring. Compact units are available in model designs with or without a control unit. In the model design without a control unit, the compact unit (and thereby the lubrication interval) is controlled by the control unit of the machine that the oil + air lubrication system is mounted on. In the model design with a control unit, the compact unit is equipped with an electronic control unit that controls the compact unit (and thereby the lubrication interval).
page 14 Details on the function and operation of the compact unit and the electronic control unit can be found in the assembly instructions for the compact unit and the operating instructions for the electronic control unit which are included in the scope of delivery of the oil + air lubrication system.
EN
Compressed air control valve (6) The compressed air control valve (6) is used to set the air pressure of the compressed air fed to the oil + air metering unit and the lubrication point lines. The compressed air transports the oil streak on the inner wall of the lubrication point line, starting from the oil + air metering unit, through the lubrication point line and to the lubrication point. The compressed air must be fed uniformly to ensure constant transport of the oil streak, which ensures constant lubricant supply to the lubrication point. The air pressure is set manually and can be read directly on the integrated pressure gauge (7) on the compressed air control valve (6). An air filter with an integrated water separator can optionally be used. Figure 1. Design of an electrically driven oil + air lubrication system (schematic diagram, subject to change) 1 Compact unit without control unit 2 Lubricant reservoir 3 Filler socket 4 Oil pressure gauge 5 Compressed air connection 6 Compressed air control valve 7 Pressure gauge for compressed air supply 8 Pressure switch for minimum air pressure 9 Oil + air metering unit
3. Design and function
page 15
Figure 1: Design of an electrically driven oil + air lubrication system
Oil
Air
EN