SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM SPECIFICATION
CONTENTS
Section
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12 13.
Scope Basis Additional Requirements Table Table 1, Plates Table 2, Pipes Table 3, Tubes Table 4, Forging Table 5, Castings Table 6, Bolts and Nuts Table 7, Bars and Shapes Table 8, Piping Fittings Table 9, Nonferrous Materials
1. SCOPE This specification lists the Japanese Standard (JIS, JPI),British Standard (BS), and Deutshe Industrie Normen (DIN) substitutes for ASTM Specifications relating to materials for plates, pipes, tubes, forging, castings, bolts and nuts, bars and shapes, piping fittings, and nonferrous materials, in general use. 2. BASIS These substitutes are not necessarily identical to the ASTM Specifications, but are equal in terms of alloy content and have a nearly equal or higher ultimate tensile strength; exceptions to this are underlined. 3. ADDITIONAL REQUIREMENTS The requirements of the ASTM Specifications not covered by the substitute specifications are noted in the Tables, with footnotes given on Section 4. 4. TABLE Substitute materials are shown in the following Tables 1 to 9.
STANDARD SPECIFICATION Table 1 PLATE ASTM A-36 Structural Steel
JIS
BS
DIN
G 3101 SS400 G 3105 SM400A
4360 Gr 40A (1) 4360 Gr 438 (1)
17100 St44-2 17100 St44-3
A-131 Structural Steel for Ships Gr A Gr B Gr CS Gr D Gr E
G 3106 SM400A G 3106 SM400B G 3105 SM400CN G 3105 SM400C (2) G 3105 SM40OCN
4360-40B 4360-40B 4360-40E 4360-40E 4360-40E
17100 St44-3 ---------
A-167 Stainless arid Heat-Resisting Chromium,-Nickel Steel Plate, Sheet, and Strip Type 302 Type 304
G 4304 SUS302 (3) G 4304 SUS304 (3)
17440/1 X10CrNiS189 17440/1 X5CrNi1810
Type 304L
G 4304 SUS304L (3)
Type 310S
G 4304 SUS310S (3)
Type 316
G 4304 SUS316 (3)
Type 316L
G 4304 SUS316L (3)
Type 321
G 4304 SUS321 (3)
Type 347
G 4304 SUS347 (3)
--1449-304S31 1501-304S15 1501-304S12 1449-304S11 1501-310S24 1449-310S24 1501-316S16 1449-316S31 1501-316S12 1449-316S11 1501-321S12 1449-321S31 1501-347S17 1449-347S31
17440/1 X2CrNi1911 ----17440/1 X5CrNiMo17122 17440/1 X2CrNiMo17132 17440/1 X6CrNiTi1810 17440/1 X6CrNiNb1810
Note (1): Specify mechanical properties, test and inspection in accordance with ASTM. Note (2): Plates over 1-3/8 Inches (35 m-n) in thickness shall be normalized. Note (3): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G 4307, respectively.
STANDARD SPECIFICATION
ASTM A-176 Stainless and Heat Resisting Chromium Steel Plate, Sheet, And Strip Type 403
JIS
G 4304 SUS403 (1)
Type 405
G 4304 SUS405 (1)
Type 410 Type 4105
BS
DIN
G 4304 SUS410 (1) G 4304 SUS410S (1)
14-09-403 S17 S2) 1501-403 S17 l2) 1449-405 S17 1501-405 S17 1449-410 S21 ---
----17440/1 X6CrAl13 --17440/1 X10Cr13 17440/1 X6Cr13
G 3127 SL2N255 G 3127 SL3N255 G 3127 SL3N275 G 3127 SL3N440
--1501-503 -----
----17280 10Ni14 ---
G 3103 S64SOM
---
Gr B Gr C
G 3103 SB48M ---
-----
SEL 16 Mo5 17155 15 Mo3 SEL 16 Mo5 ---
A-240 Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels Type 304 Type 304H Type 304L Type 316
G 4304 SUS304 (1) --G 4304 SUS304L (1) G 4304 SUS316 (1)
1501-304S15 1501-304S49 1501-304S12 1501-316S16
Type 316H Type 316L
--G 4304 SUS316L (1)
1501-316S49 1501-316S12
Type 317 Type 317L
G 4304 SUS317 (1) G 4304 SUS317L (1)
---
A-203 Pressure Vessel Plates, Alloy Steel, Nickel Gr A Gr D Gr E Gr F A-204 Pressure Vessel Plates, Alloy Steel, Molybdenum Gr A
Note (1): Note (2):
17440/1 X5CrNi1810 --17440/1 X2CrNi1911 17440/1 X5CrNiMo17122 --17440/1 X2CrNiMo17132 17440/1 X2CrHiMo18164
For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307, respectively. Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
STANDARD SPECIFICATION ASTM Type 321 Type 321H Type 347 Type 347H Type 405 Type 410 Type 410S Type 430 A-263 Corrosion-Resisting Chromium Steel-Clad Plate, Sheet, and Strip
JIS G 4304 SUS321 (1) --G 4304 SUS347 (1) --G 4304 SUS405 (1) G 4304 SUS410 (1) G 4304 SUS410S (1) G 4304 SUS430 (1)
BS 1501-321S12 1501-321S49 1501-3-07S17 1501-347S49 1501-405S17 -------
DIN 17440/1 X6CrNiTi1810 --17440/1 X6CrNiNb1810 --17440/1 X6CrAl13 17440/1 X10Cr13 17440/1 X6Cr13 17440/1 X6Cr17
G 3601 (2)
---
17440/1
G 3601 (2)
3740 (2)
17440/1
G 3602 (2)
---
17743 NiCu30Fe
G 3101 SS330 G 3101 55330 G 3101 SS400 G 3101 SS400
4360 Gr 40A/B/C 4360 Gr 40A/B/C 4360 Gr 40D 4360 Gr 43A/B/C/D
17100 St33 17100 St33 17100 St44-2 17100 St44-2
A-264 Stainless Chromic-Nickel SteelClad Plate, Sheet, and Strip A-265 Nickel and Nickel-Base Alloy-Clad Steel Plate A-283 Low and Intermediate Tensile Strength Carbon Steel Plates, Shapes, and Bars Gr A Gr B Gr C Gr D
Note (1): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307, respectively. Note (2): Specify mechanical properties, test and inspection in accordance with ASTM.
STANDARD SPECIFICATION
ASTM A-285 Pressure Vessel Plates, Carbon Steel, Low-and Intermediate-Tensile Strength Gr A & B Gr C
JIS
BS
DIN
--G 3103 S8410
1501-151 Gr 360 1501-151 Gr 430
17155 H I 17155 H II
A-299 Pressure Vessel Plates, Carbon Steel, Manganese Silicon G 3115 SPV355
---
17102 StE355
A-302 Pressure Vessel Plates, Alloy Steel Manganese-Molybderalm and Manganese-HolybdenumNickel Gr A Gr B Gr C Gr D
G 3119 SBV1A G 3119 SBV1B G 3119 SBV2 G 3119 SBV3
---------
---------
A-387 Pressure Vessel Plates, Alloy Steel Chromium-Molybdenum Gr 2 Class 1 Gr 11 Class 1 Class 2 Gr 12 Class 1 Class 2 Gr 21 Class 1 Gr 22 Class 1 Class 2 Gr 5 Class 1 Class 2 Gr 9 Class 1 Class 2
G 4109 SCMV1 G 4109 SCMV3 G 4109 SCMV3 G 4109 SCMV2 G 4109 SCMV2 G 4109 SCMV5 G 4109 SCMV4 G 4109 SCMV4 G 4109 SCMV6 G 4109 SCMV6 -----
--1501-621 1501-621 1501-620 1501-620 --1501-622 Gr 515 1501-622 Gr 515 ---------
-----
ASTM A-442 Pressure Vessel Plates, Carbon Steel, Improved Transition Properties Gr 55
JIS
---
Gr 60
G 3115 SPV235
BS
1501-151 Gr 400 1501-161 Gr 400 1501-224 Gr 400 1501-151 Gr 430 1501-161 Gr 430 1501-224 Gr 430
A-516 Pressure Vessel Plates, Carbon Steel, for Moderate and Lower Temperature Service Gr 55
DIN
SEW 680 TTSt41N
---
-
---
Gr 60
G 3118 SGV410
Gr 65 Gr 70
G 3118 SGV450 G 3118 SGV480
Note (1):
17155 13CrMo44 ----17155 10CrMo910 --SEW590 12CrMo195 -------
1501-161 Gr 400 1501-224 Gr 400 1501-161 Gr 430 1501-224 Gr 430 1501-224 Gr 460 1501-224 Gr 490
17155 H I 17155 H II 17155 17Mn4 17155 19Mn6
Recognize lacer minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
STANDARD SPECIFICATION Note (1): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM. Note (2): Specify mechanical properties, test and inspection in accordance with ASTM.
ASTM A-533 I Pressure Vessel Plates,Alloy Steel Quenched and Tempered Manganese- Molybdenum and Manganese- Molybdenum Nickel
JIS
BS
Type A Class 1 Class 2 Type B Class 1 Class 2 Type C Class 1 Class 2
G 3120 SQV1A G 3120 SQV1B G 3120 SQV2A G 3120 SQV2B G 3120 SQV3A G 3120 SQV3B
-------------
A-537 Pressure Vessel Plates, HeatTreated, Carbon-ManganeseSilicon Steel Class 1
G 3115 SPV355N
Class 2
G 3115 SPV450Q
1501-224 Gr 490 (1) ---
DIN
-------------
17155 19Mn6 17102 StE355 ---
A-570 Steel, Sheet and Strip, Carbon, Hot-Rolled, Structural Quality. Gr 30 Gr 33 Gr 36 Gr 40 Gr 45 Gr 50
G 3101 SS330 G 3101 SS400 G 3101 SS400 G 3101 SS400(1) G 3101 SS490 G 3101 SS490(1)
1449-HR 34/20 (1) 1449-HR 37/23 1449-KR 37/23 1449-HR 43/25 1449-HR 43/25 (1) 1449-HR 50/35
17100 St33 17100 St44-2 17100 St44-2 17100 St44-2 17100 St52-3 17100 St52-3
A-611 Steel, Sheet, Carbon, Cold-Rolled Structural Quality Gr B Gr C Gr D
G 3141 SPCC (2) G 3141 SPCC (2) G 3141 SPCC (2)
-------
--1623.1 St12 ---
STANDARD SPECIFICATION Note (1): Specify Impact Test requirement per ASTM. Note (2): Recognize lager minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
ASTM A-652 Pressure Vessel Plates, Carbon Manganese, for Moderate and Lower Temperature Service Gr A Gr B Gr C
JIS
G 3126 SLA235 (1) G 3126 SLA325 (1)(2) G 3126 SLA360 (1)
BS
-------
DIN
--17102 EStE315 17102 EStE355
STANDARD SPECIFICATION Table 2 PIPE Note (1): Specify carbon, manganese, or silicon contents to accordance with ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
ASTM A-53 Pipe, Steel, Black and Hot-Dipped Zinc-Coated Welded and Seamless
JIS
Type F Gr A
G 3452 SGP G 3454 STPG370
Gr B
G 3454 STPG410
BS
DIN
1387 3601 ERW360 S360 3601 ERW410 S410
1615 St33 1626 St37.0 1629 St37.0 1626 St44.0 1629 St44.0
3602 HFS360 3602 CFS360 3602 HFS410 3602 CFS410 3602 HFS460 3602 CFS460
17175 St35.8
A-106 Seamless Carbon Steel Pipe for High-Temperature Service Gr A
G 3456 STPT370
Gr B
G 3.455 STPT410
Gr C
G 3456 STPT480
17175 St45.8 17175 St45.8
A-134 Pipe, Steel, Electric-Fusion (Arc)Welded (Size NPS 16 and over) Material A 283 Gr A – D
G 3457 STPY400
A 285 Gr A – C A 570 Gr 30 – 40 A 36
G 3457 STPY400(1) G 3457 STPY400 (1)(2) G 3457 STPY400
3602 SAW410 3601 SAW410 ----3602 SAW410 3601 SAW410
------
STANDARD SPECIFICATION Note (1):
Specify electric resistance-welding.
Note (2):
Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM. Specify carbon, manganese, or silicon contents in accordance with ASTM.
Note (3):
ASTM A-135 Electric-Resistance-Welded Steel Pipe Gr A Gr B
JIS
BS
DIN
G 3454 STPG370 (1) G 3454 STPG410 (1)
3601 ERW360 3601 ERW410
1626 St37.0 1626 St44.0 .
G 3457 STPY400 (2)(3)
3602 SAW410 (2) 3601 SAW410 (2)
---
A 570 Gr 30-45
G 357 STPY400 (2)(3)
---
A 570 Gr 50
---
3602 SAW 410 (2) 3601 SAW 410 (2) 3502 SAW 460 (2)
TP 304 (18Cr-8Ni) TP 304H (18Cr-8Ni) TP 304L (18Cr-8Ni) TP 309 (23Cr-12Ni) TP 310 (25Cr-20Ni) TP 316 (16Cr-12Ni-21Mo)
G 3459 SUS304TP G 3459 SUS304HTP G 3459 SUS304LTP G 3459 SUS309STP G 3459 SUS310STP G 3459 SUS316TP
3605-304S18,S25 3605-304S59 3605-304S14,S22 ----3605-316S18,S26
TP 316H (16Cr-12Ni-2Mo) TP 316L (16Cr-12Ni-2Mo)
G 3459 SUS316HTP G 3459 SUS316LTP
3605-316S59 3605-316S14,S22
TP 321 (18Cr-10Ni-Ti) TP 321H (l8Cr-12Ni-Ti) TP 347 (18Cr-10Ni-Cb)
G 3459 SUS321TP G 3459 SUS321HTP G 3459 SUS347TP
3605-321S18,S22 3605-321S59 3605-347S18,S17
TP 347H (18Cr-10Ni-Cb)
G 3459 SUS347H TP
3605-347S59
17457/58 X5CrNi1810 --17457/58 X2CrNi1911 ----17457/58 X5CrNiMo17122 17459E X6CrNiMo1713 17457/58 X2CrNiMo17132 17457/58 X6CrNiTi1810 SEW470 X12CrNiTi189 17457/58 X6CrNiNb1810 ---
A-139 Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and over) Gr A – E A-211 Spiral-Welded Steel or Iron Pipe
A-312 Seamless and Welded Austenitic Stainless Steel Pipe
STANDARD SPECIFICATION Note (1):Recognize Lower minimum tensile or yield strengths of the underlined substitute materials in design consideration or specify minimum tensile and yield strengths per ASTM. Note (2):VdTuv-Werkstoftblatt
ASTM A-333 Seamless and Welded Steel Pipe for Low-Temperature Service
JIS
Gr 1
G 3460 STPL380
Gr 3 (3-1/2Ni)
G 3460 STPL450
Gr 6
---
Gr 8 (9Ni)
G 3460 STPL690
BS
DIN
3603-CFS410 LT50 3603-HFS410 LT50 3603-ERW410 LT50 3603-CEW410 LT50 3603-HFS503 LT100 3603-CFS503 LT100 3603-CFS410 LT50 3603-HFS410 LT50 3603-ERW410 LT50 3603-CEW410 LT50 3603-HFS509 LT196 3603-CFS509 LT196
17173 TTSt35N 17174 TTSt35N
17175 15Mo5 Wbl 007/2 12CrMo195 (2)
17173 l0Ni14 SEW680 TTSt45N
17173 X8Ni9
A-335 Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
Gr P1 (C-1/2Mo) Gr P5 (5Cr-1/2Mo)
G 3458 STPA12 G 3458 STPA25
--3604 CFS625 (1)
Gr P9 (9Cr-1Mo)
G 3458 STPA26
3604 HFS625 (1) 3604-CFS629-470 (1)
Gr P11 (1-1/4Cr-1/2Mo)
G 3458 STPA23
Gr P12 (1Cr-1/2Mo)
G 3458 STPA22
Gr P22 (2-1/4Cr-1Mo)
G 3458 STPA24
3604 CF5621 3604 HFS621 3604 CFS620-460 (1) 3604 HFS620-460 (1) 3604 CFS622 3604 HFS622
Wbl 109 X12CrMo91 (2) 17175 13CrMo44 17175 13CrMo44 17175 l0CrMo910
STANDARD SPECIFICATION Note (1): Specify seamless.
ASTM A-358 Electric-Fusion-welded Austenitic Chromium-Nickel Alloy Steel Pipe For High-Temperature Service
Grade 304 304L 316 316L 321 347
Material A240, Type 304 A240, Type 304L A240, Type 316 A240, Type 316L A240, Type 321 A240, Type 347
JIS
BS
DIN
G 3468 SUS304TPY G 3468 SUS304LTPY G 3468 SUS316TPY G 3468 SUS316LTPY G 3468 SUS321TPY G 3468 SUS347TPY
3605 LWHT 304S18 3605 LWHT 304S14 3505 LWHT 316S18 3605 LWHT 316S14 3605 LWHT 321S18 3605 LWHT 347S18
17457 17457 17457 17457 17457 17457
X5CrNi1810 X2CrNi1911 X5CrNiMo17122 X2CrNiMo17132 X6CrNiTi1810 X6CrNiNb1810
A-376 Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service TP 304 (18Cr-8Ni)
G 3459 SUS304TP (1)
3605-304S18
TP 304H (18Cr-8Ni) TP 316 (16Cr-12Ni-2Mo) TP 316H (16Cr-12Ni-2Mo)
G 3459 SUS304HTP (1) G 3459 SUS316TP (1) G 3459 SUS316HTP (1)
3605-304S59 3605-316S18 3605-316S59
TP 321 (18Cr-10Ni-Ti) TP 321H (18Cr-10Ni-Ti) TP 347 (18Cr-10Ni-Cb) TP 347H (18Cr-10Ni-Cb)
G 3459 SUS321TP (1) G 3459 SUS321HTP (1) G 3459 SUS347TP (1) G 3459 SUS347HTP (1)
3605-321S18 3605-321S59 3605-347S18 3605-347S59
17459 X6CrNi1811 E --17458 X5CrNiMo17122 17459 X6CrNiMo1713 E 17458 X6CrNiTi810 --17458 X6CrNiNb1810 ---
G 3468 SUS304TPY G 3463 SUS304LTPY G 3468 SUS316TPY G 3468 SUS316LTPY G 3468 SUS321TPY G 3468 SUS347TPY
-------------
17457 17457 17457 17457 17457 17457
A-409 Welded Large Diameter Austenitic Steel Pipe for Corrosive or High Temperature Service TP 304 (18Cr-8Ni) TP 304L TP 316 (16Cr-12Ni-2Mo) TP 316L TP 321 (18Cr-10Ni-Ti) TP 347 (18Cr-10Ni-Cb)
X5CrNi810 X2CrNi1911 X5CrNiMo17122 X2CrNiMo17132 X6CrNiTi1810 X6CrN iNb1810
STANDARD SPECIFICATION Note (i): Specify electric resistance-welding. Note (2): Maximum carbon content shall be 0.15%. Note (3): Specify Impact Test requirement per ASTM.
ASTM A-524 Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures Gr 1 Gr 11
JIS/JPI
BS
DIN
---
---
SEW680 TTSt41 ---
G 3454 STPG370 (1)(2)
---
1626 St37.0
JPI-SB42 JPI-SB46 JPI-SB49 JPI-SLA24B (3) JPI-SLA33B (3) ----JPI-SPV24 --JPI-SL3N28
---------------------
---------------------
A-587 Electric-Welded Low-Carbon Steel Pipe for the Chemical Industry
A-671 Electric-Fusion-Welded Steel pipe for Atmospheric and Lower Temperatures Grade CA55 CB60 CB70 CB70 CC60 CC65 CD70 CE55 CE60 CF70 CF71 CK75
Material A285 Gr C A515 Gr 60 A515 Gr 65 A515 Gr 70 A516 Gr 60 A516 Gr 65 A537 CL 1 A442 Gr 55 A442 Gr 60 A203 Gr B A203 Gr E A299
STANDARD SPECIFICATION Note (1): Specify Impact Test requirement per ASTM. Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
ASTM A-672 Electric-Fusion-Welded Steel Pipe for High- Pressure Service at Moderate Temperature
Grade A55 B55 B60 B65 B70 C55 C60 C65 C70 D70 E55 E60 L65 L70 L75 N75
Material A285 Gr C A515 Gr 55 A515 Gr 60 A515 Gr 65 A515 Gr 70 A516 Gr 55 A516 Gr 60 A516 Gr 65 A516 Gr 70 A537 CL 1 A442 Gr 55 A442 Gr 60 A204 Gr A A204 Gr B A204 Gr C A299
JIS/JPI
JPI-SB42 --JPI-SB42 JPI-SB46 JPI-SB49 --JPI-SLA24B (1) JPI-SLA33B (1) ------JPI-SPV24 JPI-SB46M JPI-SB49M (2) -----
BS
DIN
---------------------------
---------------------------
-----
-----
STANDARD SPECIFICATION
ASTM/API A-691 Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High- Pressure Service at High Temperatures Grade Material CM-65 A204 Gr A CM-70 A204 Gr B CM-75 A204 Gr C CMSH-70 A537 CL 1 CMS-75 A299 ½ Cr A337 Gr 2 CL 1 1 Cr A387 Gr 12 CL 1 1-1/4 Cr A387 Gr 11 CL1 2-1/4 Cr A387 Gr 22 CL1 5 Cr A387 Gr 5 CL 1 API 5L Line Pipe Gr A25 Gr A
JIS/JPI
DIN
JPI-SB46M JPI-SB49M --------JPI-SCMV2 JPI-SCMV3 JPI-SCMV4 JPI-SCMV6
---------------------
--------_------------
63452 SGP 63454 STPG370
1387 3601 ERW 360 3601 S 360 3601 ERW 430 (1) 3601 S 430 (1) 3601 SAW 430 (1) 6327 Part 1-8 (1) ---------------------
--17172 StE210.7
Gr B
63454 STPG410
Gr X42 Gr X46 Gr X52 Gr X56 Gr X60 Gr X65 Gr X70 -------
--------------63455 STS370 63455 STS410 63455 STS480
Note (1):
BS
17172 StE240.7
17172 StE290.7 17172 StE320.7 17172 StE360.7 17172 StE385.7 17172 StE415.7 17172 StE445.7TM 17172 StE480.7TM 1630 St37.4 1630 St44.4 1630 St52.4
Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
Table 3 TUBES ASTM A-161 Seamless Low-Carbon and Carbon Molybdenum Steel Still Tubes for Refinery Service Low Carbon Steel
Gr T1
JIS
BS
DIN
G 3461 ST340 (1) (2)
3059 HFS320 (2) 3059 CFS320 (2)
17175 St35.8
G 3462 STBA12 (1)(2)(3) G 3467 STFA12 (2)
---
17175 15Mo5
3059 ERW320 (3) 3059 CEW320 (3) 3059 ERW360 3059 CEW360 (3) 3059 ERW440 (3) 3059 CEW440 (3)
17177 St37.8
A-178 Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler Tubes Gr A
G 3461 STB340 (40
Gr C
G 3461 STB410 (4)
Gr D
---
17177 St42.8 ---
A-179 Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes G 3461 STB340 (1)(5)(6)
3606 CFS 320 3059 S1 360 (5)(6)
Note (1): Specify seamless. Note (2): Maximum hardness shall be as follows: Item Hot rolled tubes Cold drawn tubes
Note (3): Specify killed steel. Note (4): Specify electric resistance-welding. Note (5): Specify cold drawn. Note (6): Maximum hardness shall be Rockwell B72.
Carbon Steel HB 137 HB 125
17175 St35.8
STANDARD SPECIFICATION
ASTM A-192 Seamless Carbon Steel Boiler Tubes for High- Pressure Service
JIS
BS
DIN
G 3-061 STB340 (1)(2)
3059 HFS 320 (2) 3059 CFS 320 (2) 3059 S1 360 (2) 3059 S2 360 (2)
17175 St35.8
Gr T5 Gr T9
G 3462 STBA25 (3)(4) G 3462 STBA26 (3)(5)
Wbl 007/2 12CrMio195 (6) Wbl 109 X12CrMo91 (6)
Gr T11 Gr T22
G 3462 STBA23 (3)(4) G 3462 STBA24 (3)(4)
3606 CFS 625 3059 S1 629-470 (3)(5) 3059 S2 629-470 (3)(5) 3606 CFS621 3606 CFS622 3059 S1 622-440 (3)(4) 3059 S2 622-440 (3)(4)
A-199 Seamless Cold-Drawn Intermediate Alloy-Steel Heat-Exchenger and Condenser Tubes
17175 13CrMo44 17175 10CrMo910
A-200 Seamless Intermediate Alloy-Steel Still Tubs for Refinery Service Gr T5 Gr T7 Gr T9
Gr T11 Gr T22
G 3462 STBA25 (4) G 3467 STFA25 (4) --G 3462 STBA26 (5) G 3467 STFA26 (5)
G 3462 STBA23 (4) G 3467 STFA23 (4) G 3462 STBA24 (4) G 3467 STFA24 (4)
Note (1): Specify seamless. Note (2): Maximum hardness shall be Rockwell 677. Note (3): Specify cold drawn. Note (4): Maximum hardness shall be Rockwell 885. Note (5): Maximum hardness shall be Rockwell B89. Note (6): VdTuv-Herkstoftblatt
3604 CFS625 (4) 3604 HFS625 (4) --3604 CFS629-470 (5) 3604 HFS629-470 (5) 3059 S1 629-470 (5) 3059 S2 629-470 (5) 3604 CFS621 (4) 3604 HES621 (4) 3059 S1 622-440 (4) 3604 CFS622 (4) 3604 HFS622 (4)
Wbl 007/2 12CrMo195 (6) --Wbl 109 X12CrMo91 (6)
17175 13CrMo44 17175 10CrMo910
STANDARD SPECIFICATION
ASTM A-209 Seamless Carbon-Molybdenum Alloy-Steel Boiler and Super Heater Tubes
JIS
Gr T1
G 3462 STBA12 (1)(2)
Gr Tla
G 3462 STBA13 (1)(3)
Gr Tlb
---
A-210 Seamless Medium-Carbon Steel Boiler and Super heater Tubes Gr A1
BS
DIN
3059 S1 243 (2) 3059 S2 243 (2) 3059 S1 243 (3) 3059 S2 243 (3) ---
17175 15Mo5 --17175 15Mo5 ~ ---
G 3461 STB410 (1)(4)
3059 S1 440 S2 440 (4)
17175 St45.8
Gr T 5
G 3462 STBA25 (5)
3606 CFS 625
Gr T 11 Gr T 12
G 3462 STBA23 (5) G 3462 STBA22 (1)(5)
Gr T 22
G 3462 STBA24 (5)
Gr TP 304 Gr TP 3D4H Gr TP 304L Gr TP 310 Gr TP 316 Gr TP 316H Gr TP 316L Gr TP 321 Gr TP 321H Gr TP 347 Gr TP 347H
G 3463 SUS304 TB (1)(6) G 3463 SUS304H T8 (1)(6) G 3463 SUS304L TB (1)(6) G 3463 SUS310S TB (1)(6) G 3463 SUS316 TB (1)(6) G 3463 SUS316H TB(1)(6) G 3463 SUS316L TB (1)(6) G 3463 SUS321 TB (1)(6) G 3463 SUS321H TB(1)(6) G 3463 SUS347 TB (1)(6) G 3463 SUS347H TB(1)(6)
3606 CFS 621 3506 CFS 620 3059 S1/S2 620 (5) 3606 CFS 622 3059 S1/S2622440/490(5) 3606 CFS 304S25 3059 CFS304S59 (6) 3606 CFS304S22 --3606 CFS316S25 3059 CFS316S59 (6) 3606 CFS316S29 3606 CF5321S22 3059 CFS321S59 (6) 3606 CFS347S17 3059 CFS347S59 (6)
Wbl 007/2 12CrMo195 (7) 17175 13CrMo44 17175 13CrMo44
A-213 Seamless Ferritic and Austenitic Alloy-Steel Boiler, Super heater and Heat-Exchanger Tubes
Note (1): Specify seamless. Note (2): Maximum hardness shall be Rockwell B90. Note (3): Maximum hardness shall be Rockwell B81. Note (4): Maximum hardness shall be Rockwell B79. Note (5): Maximum hardness shall be Rockwell B85. Note (6): Maximum hardness shall be Rockwell B90. Note (7): VdTuv-Werkstoftblatt
17175 10CrMo910
17458 X5CrNi1810 --17458 X2CrNi1911 --17458 X5CrNiMo17122 17459E X6CrNiMo1713 17458 X2CrNiMo17132 17458 X6CrNiTi1810 --17458 X6CrNiNb1810 ---
STANDARD SPECIFICATION
ASTM A-214 Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes
JIS
BS
DIN
G 3461 STB340 (1)(2)
3606 ERW 320 3059 ERW 320 (2) 3059 CEW 320 (2) 3059 ERW 360 (2) 3059 CEW 360 (2)
17177 St37.8
G 3461 STB340 (1)(2)
3059 ERW320 (2) 3059 CEW320 (2) 3059 ERW360 (2) 3059 CEW360 (2)
17177 St37.8
G 3463 SUS304 TB (3) G 3463 SUS304H TB (3) G 3463 SUS304L TB (3) G 3463 SUS309S TB (3) G 3463 SUS310S TB (3) G 3463 SUS316 TB (3) G 3463 SUS316H TB (3) G 3463 SUS316L TB (3) G 3463 SUS321 TB (3) G 3463 SUS321H TB (3) G 3463 SUS347 TB (3) G 3463 SUS347H TB (3)
--3059-ERW304S59 (3) --------3059-ERW316S59 (3) ----3059 ERW321S59 (3) --3059-ERW347S59 (3)
17457 X5CrNi1810 --17457 X2CrNi1911 ----17457 X5CrNiMo17122
A-226 Electric-Resistance-Welded Carbon Steal Boiler and Superheater Tubes for High-Pressure Service
A-249 Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condense; Tubes TP 304 TP 304H TP 304L TP 309 TP 310 TP 316 TP 316H TP 316L TP 321 TP 321H TP 347 TP 347H
Note (1): Specify electric resistance-welding. Note (2): Maximum hardness shall be Rockwell B72. Note (3): Maximum hardness shall be Rockwell B90.
17457 X2CrNiMo17132 17457 X6CrNiTi1810 --17457 X6CrNiNb1810 ---
STANDARD SPECIFICATION
ASTM A-268 Seamless and Welded Ferritic Stainless Steel Tubing for General Service TP 410 TP 430
G 3463 SUS410 TB (1) G 3463 SUS430 TB (2)
-----
-----
A-269 Seamless and Welded Austenitic Stainless Steel Tubing for General Service TP 304 TP 304L TP 316 TP 316L TP 321 TP 347
G 3463 SUS304 TB (2) G 3463 SUS304L TB (2) G 3463 SUS316 TB (2) G 3463 SUS316L TB (2) G 3463 SUS321 TB (2) G 3463 SUS347 TB (2)
3605-304S18,S25 (2) 3605-304S14,S22 (2) 3605-316S18,S26 (2) 3605-316S14,S22 (2) 3605-321S18,S22 (2) 3605-347S18,S17 (2)
-------------
G 3463 SUS304 TB (2)(3) G 3467 SUS304 TF (2) G 3463 SUS304H TB (2)(3) G 3467 SUS304H TF (2) G 3463 SUS316 TB (2)(3) G 3467 SUS316 TF (2) G 3463 SUS316 HTB (2)(3) G 3467 SUS316 HTF (2) G 3463 SUS321 TB (2)(3) G 3467 SUS321 TF (2) G 3463 SUS32114 TB (2)(3)
3605-304S18 (2)
17459E X6CrNi1811
3605-304S59 (2) 3059-CFS304S59 (2) 3605-316S18 (4)
---
3605-316S59 (4) 3059-316S59 (4) 3605-321S18 (2)
17459E X6rNiMo1713
3605-321S59 Gr 1010 (2) 3059-CFS321S59 Gr 1010(2) 3605-347S18 (2)
---
3605-347S59 (2) 3059-CFS347S59 (2)
-----
A-271 Seamless Austenitic Chromium Nickel Steal Still Tubes for Refinery Service TP 304 TP 304H TP 316 TP 316H TP 321 TP 321H
JIS
G 3467 SUS321H TF (2) TP 347 TP 347H
G 3463 SUS347 TB (2)(3) G 3467 SUS347 TF (2) G 3463 SUS347H TB (2)(3) G 3467 SUS347H TF (2)
Note (1): Maximum hardness shall be Rockwell B95. Note (2): Maximum hardness shall be Rockwell B90. Note (3): Specify seamless. Note (4): Maximum carbon content shall be 0.21%
BS
DIN
17458 X5CrNiMo17122
17458 X6CrNiTi1810
17458 X6CrNiNb1810
STANDARD SPECIFICATION
ASTM A334 Seamless and Welded Carbon And Alloy-Steel Tubes for Low-Temperature Service Gr 1
JIS
G 3464 STBL380 (1)
Gr 3
G 3464 STBL450 (2)
Gr 6
---
Gr 8
G 3464 STBL690 (2)
Note (1): Maximum hardness shall be Rockwell B85. Note (2): Maximum hardness shall be Rockwell B90.
BS
3603 CEW410 LT50 (1) 3603 CFS410 LT50 (1) 3603 ERW410 LT50 (1) 3603 HFS410 LT50 (1) 3603 CFS503 LT100 (2) 3603 HFS503 LT100 (2) 3603 CEW410 LT50 (2) 3603 CFS410 LT50 (2) 3603 ERW410 LT50 (2) 3603 HFS4110 LT50 (2) 3603 CFS509 LT196 (2) 3603 HFS509 LT196 (2)
DIN
17173 T7St35N 17174 TTSt35N
17173 10Ni14 SEW680 TTSt45N
17173 X8Ni9
STANDARD SPECIFICATION Table 4 FORGINGS
ASTM A-105 Forging, Carbon Steel, For Piping Components
JIS
BS
G 3202 SFVC2A
1503-221-490
---
A-181 Forging, Carbon Steel, for General - Purpose Piping Class 60 Class 70
G 3202 SFVC1 G 3202 SFVC2A
1503-221-430 1503-221-490
17200 C22N ---
A-182 Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High –Temperature Service F1 (C-1/2Mo) FS (5Cr-1/2Mo) F9 (9Cr-1Mo)
G 3203 SFVAF1 G 3203 SFAF58 G 3203 SFVAF9
1503-245-420 (1) 1503-625-520 ---
F11 (1-1/4Cr-I/2Mo) F12 (1Cr-1/2Mo) F21 (3Cr-1Mo) F22 (2-1/4Cr-1Mo) F304 (18Cr-8Ni) F304H (18Cr-8Ni) F304L (18Cr-8Ni) F316 (16Cr-12Ni-2Mo) F316H (16Cr-12Ni-2Mo) F316L (16Cr-12Ni-2Mo) F321 (18Cr-10Ni-Ti) F321H (18Cr-10Ni-Ti) F347 (18Cr-10Ni-Cb) F347H (18Cr-10Ni-Cb)
G 3203 SFVAF11A G 3203 SFVAF12 G 3203 SFVAF21B G 3203 SFVAF22B G 3214 SUS304 G 3214 SUS304H G 3214 SUSF304L G 3214 SUSF316 G 3214 SUSF316H G 3214 SUS316L G 3214 SUS321 G 3214 SUSF321H G 3214 SUSF347 G 3214 SUSF347H
1503-621-460 1503-620-540 --1503-622-560 1503-304S31 1503-304S51 1503-304S11 1503-316S31 or 33 1503-316S51 1503-316S11 or 13 1503-321S31 1503-321S51-510 1503-347S31 1503-347S51
VdTuv201 16Mo5 VdTuv1207 12CrMo195 W.St.Nr17386 X12CrMo910 SEW550 16CrMo44 SEW550 13CrMo44 --SEW550 10CrMo9I0 17440 X5CrNi1810 --17440 X2CrNi1911 17440 X5CrNiMo17122 --17440 X2CrNiMo17132 17440 X6CrNiTi1810 --17440 X6CrNiNb1810 ---
Note (1):
DIN
Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
STANDARD SPECIFICATION
ASTM A-226 Forging, Carbon Steel, for Pressure Vessel Component
JIS
BS
DIN
Class 1 Class 2 Class 4
G 3202 SFVC1 G 3202 SFVC2A G 3202 SFVC2B
1503-221-430 1503-221-490
17200 C22N ---
A-336 Steel Forging, Alloy, for Pressure and High- Temperature Parts
Refer to A-182
Refer to A-182
Refer to A-182
LF1 LF2
G 3205 SFL1 G 3205 SFL2
SEW680 TTSt41 SEW680 TTStE36
LF3 (3-1/2Ni)
G 3205 SFL3
1503-221-430 (1) 1640 WPLO 1503-221-490 (1) 1640 WPL3 1503-503-490 (1)
A-350 Forging, Carbon and Low-Alloy Steel, Requiring Notch Toughness Testing for Piping Component
17280 10Ni14
A-508 Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forging for Pressure Vessel Class 1 Class 2 Class 3
G 3202 SFVC2B G 3204 SFVQ2A G 3204 SFVQ1A
-------
--SEW640 22NiMoCr37 SEW640 20MrMoNi55
G 3202 SFVC2B G 3204 SFVQ2A G 3204 SFVQ1A
1503-221-490 (1)(2) -----
-------
A-541 Steel Forging, Carbon and Alloy Quenched and Tempered, for Pressure Vessel Component Class 1 Class 2 Class 3
Note (1): Specify Impact Test requirement per ASTM. Note (2): Specify heat treatment and mechanical properties per ASTM.
STANDARD SPECIFICATION Table 5 CASTINGS
ASTM A-27 Steel Castings, Carbon, for General Application Gr 60-30 Gr 65-35 Gr 70-36
JIS
BS
DIN
G 5101 SC410 (1) G 5101 SC450 (1) G 5101 SC480 (1)
3100 Steel A1 --3100 Steel A2
1681 GS-38 (2) 1681 GS-45 1681 GS-52
Gr 32510 Gr 35018
G 5702 FCM3340 G 5702 FCM3360
6681 B35-12 ---
1692 GTS-35-10 1692 GTS-35-10 (2)
A-48 Gray Iron Castings Class 20 Class 25 Class 30 Class 35 Class 40 Class 45 Class 50 Class 55 Class 60
G 5501 FC150 G 5501 FC200 G 5501 FC200 (2) G 5501 F 250 G 5501 FC300 G 5501 FC300 (2) G 5501 FC350 -----
1452 Gr 150 1452 Gr 180 1452 Gr 220 1452 Gr 260 1452 Gr 300 1452 Gr 300 (2) 1452 Gr 350 1452 Gr 400 ---
1691 GG-15 1691 GG-20 1691 GG-20 (2) 1691 GG-25 1691 GG-30 1691 GG-30 (2) 1691 GG-35 ---
G 5501 FC200 G 5501 FC250 G 5501 FC300
1452 Gr 180 1452 Gr 260 1452 Gr 300
1691 GG-15 1691 GG-25 1691 GG-30
A-47 Ferrltic Malleable Iron Castings
A-126 Gray Iron Castings for Valves Flanges and Pipe Fittings Class A Class 6 Class C
Note (1): Specify carbon, manganese, or silicon contents in accordance with ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
STANDARD SPECIFICATION
ASTM A-216 Steel Castings, Carbon, Suitable for Fusion Welding, For High-Temperature Service WCA WCB WCC
JIS
BS
DIN
G 5151 SCPH1 (1) G 5151 SCPH2 (1) ---
1504-161 Gr 430 1504-161 Gr 480 1504-161 Gr 540 (2)(3)
17245 GS-C25 17245 GS-C25 ---
A-217 Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service WC1 (C-1/2Mo) WC6 (1-1/4Cr-1/2Mo) WC9 (2-1/4Cr-1Mo) C5 (Cr-1/2Ho) C12 (9Cr-1Mo)
G 5151 SCPH11 (1) G 5151 SCPH21 (1) G 5151 SCPH32 (1) G 5151 SCPH61 (1) ---
1504-245 1504-621 1504-622 1504-625 1504-629
17245 GS-22Mo4 17245 GG-17CrMo55 17245 CS-19CrMo910 SEW 595 GS-2CrMo195 SEW 595 GS-2CrMo101
G 5122 SCH2 G 5122 SCH11 G 5122 SCH17 G 5122 SCH12 G 5122 SCH13 G 5122 SCH18 G 5122 SCH22 or 21 G 5122 SCH19 G 5122 SCH15 G 5122 SCH20
----3100-309C40 3100-302C35 3100-309C30 --3100-310C40 3100-311C11 3100-330C12 3100-331C60
---------------------
A-297 Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application Gr HC Gr HD Gr HE Gr HF Gr HH Gr HI Gr HK Gr HN Gr HT Gr HU
Note (1):Test and inspect the product in accordance with ASTH, except for the chemical analysis and mechanical properties of the steel. Note (2): Specify carbon, manganese, or silicon contents in accordance with ASTM. Note (3): Specify elongation in accordance with ASTM.
STANDARD SPECIFICATION
ASTM A-338 Malleable Iron Flanges, Pipe Fittings, and Valve Parts for Railroad, Marine, and Other Heavy Duty Service at Temperatures up to 650°F (345°C)
JIS
A-351 Steel Castings, Austenitic, for High-Temperature Service Gr CF3 (18Cr-8Ni)
G 5121 SCS19A (1)
Gr CF3A (18Cr-8Ni) Gr CF3M (17Cr-10Ni-2Mo)
--G 5121 SCS16A (1)
Gr CF8 (18Cr-8Ni)
G 5121 SCS13A (1)
Gr CF8A (18Cr-8Ni) Gr CF8C (20Cr-10Ni-Cb)
--G 5121 SCS21 (1)
Gr CF8M (18Cr-10Ni-2Mo)
G 5121 SCS14A (1)
Gr CH10 (25Cr-13Ni) Gr CH20 (25Cr-13Ni) Gr CK20 (25Cr-20Ni) Gr CN7M (28Ni-20Cr2Mo-3Cb) Gr HK40 (25Cr-20Ni)
G 5121 SCS17 (1)(2) G 5121 SCS17 (1)(3) G 5121 SCS18 (1) G 5121 SCS23 (1) G 5122 SCH22 (1)
BS
1504-304C12 (2) 3100-304C12 (2) --1504-316C12 (2) 3100-316C12 (2) 1504-304C15 3100-304C15 --1504-347C17 3100-347C17 1504-316C16 3100-316C16 --3100-309C30 --1504-332C11 1504-310C40 3100-310C40
DIN
------17445 G-X6CrNi189 _-17445 G-X5CrNiNb189 17445 G-X6CrNiMo1810 -----------
Note (1): Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the steel. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM. Note (3): Specify mechanical properties, test and inspection in accordance with ASTM.
STANDARD SPECIFICATION
ASTM A-352 Steel Castings, Ferritic and Martensitic, for PressureContaining Parts Suitable for Low-Temperature Service LCB LC1 (C-1/2Mo)
JIS
G 5152 SCPL1 (1) G 5152 SCPL11 (1)
LC2 (2-1/2Ni) LC3 (3-1/2Ni)
G 5152 SCPL21 (1) G 5152 SCPL31 (1)
LC9
---
BS
DIN
1504-161 Gr 480 LT40 1504-245 LT50 3100-BL1 --1504-503 LT60 3100-BL2 ---
SEW685 GS-CK24 ---
88243, APPENDIX-1 FCD-S
2789 Gr 420/12 (2)
---
G 5122 SCH13 (3)
3100-309C32
---
-------
3071-NAI 3071-NA2 (4) 3071-NA3
-------
--SEW685 GS-10Ni14 ---
A-395 Ferritic Ductile Iron PressureRetaining Castings for Use at Elevated Temperatures
A-447 Steel Castings, Chromium-Nickel -Iron Alloy Castings (25-12 Class) for High-Temperature Service
A-494 Casting, Nickel and Nickel Alloy M-35-1 M-30H M-25S
Note (1): Test and inspect the product in accordance with ASTH, except for the chemical analysis and mechanical properties of the steel. Note (2): Specify ferritizing heat treatment, chemical requirement and mechanical properties, except for tensile and yield strengths. Note (3): Specify mechanical properties, test and inspection in accordance with ASTM Note (4): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.
STANDARD SPECIFICATION
ASTM A-536 Ductile Iron Castings Gr 60-40-18 Gr 65-45-12 Gr 80-55-06 Gr 100-70-03
JIS
BS
DIN
G 5502 FCD450 (1) G 5502 FCD500 (1) G 5502 FCD600 (1) G 5502 FCD700 (1)
2789 Gr 420/12 2789 Gr 500/7 2789 Gr 600/3 (2) 2789 Gr 700/2 (2)
--1693 GGG-50 1693 GGG-60 1693 GGG-70
A-743 Castings, Iron-Chromium, Iron-Chromium Nickel, Nickel Base, Corrosion Resistant, for General Application Gr CA-15 Gr CA-40
G 5121 SCS1 (3) G 5121 SCS2 (3)
17445 G-X20Cr14 ---
Gr CF-3
G 5121 SCS19A (3)
Gr CF-3M
G 5121 SCS16A (3)
Gr CF-8
G 5121 SCS13A (3)
Gr CF-8C Gr CF-8M
G 5121 SCS21 (3) G 5121 SCS14A (3)
Gr CF-20 Gr CH-20 Gr CK-20 Gr CN-7M
G 5121 SCS12 (3) G 5121 SCS17 (3) G 5121 SCS18 (3) G 5121 SCS23 (3)
3100-410C21 (2) 1504-420C29 3100-420C29 1504-344C12 3100-304C12 1504-316C12 3100-316C12 1504-304C15 3100-304C15 1504-347C17 1504-316C16 3100-316C16 --3100-309C30 --1504-332C11
----17445 G-X6CrNi189 17445 G-X5CrNiNb189 17445 G-X6CrNiMo1810 ---------
Note (1): Specify elongation in accordance with ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM. Note (3): Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the steel.
STANDARD SPECIFICATION Table 6 BOLTS AND NUTS
ASTM A-193 Alloy-Steel and Stainless Steel Bolting Materials for High Temperature Service Gr B5 (5Cr) Gr B6 (12Cr) Gr B7 (Cr-Mo)
JIS
BS
DIN
G 4107 SNB5 G 4303 SUS410 G 4107 SNB7
--1506-410S21-772 1506-630-860
Gr B7M (Cr-0.2Mo)
G 4107 SNB7 (1)
1506-630-690
Gr B8 CL 1 (304 sol.trt.) CL 4 (304 str.hd.) Gr B8C CL 1 (347 sol.trt.) CL 2 (347 str.hd.) Gr B8M CL 1 (316 sol.trt.) CL 2 (316 str.hd.) Gr B8T CL 1 (321 sol.trt.) CL 2 (321 str.hd.) Gr B16 (Cr - Mo - V)
G 4303 SUS304 (2)
1506-304S31
--1654 X10Cr13 17200 42CrMo4 17240 24CrMo5 (3) 17200 42CrMo4 17240 24CrMo5 (3) 17440 X5CrNi1810
G 4303 SUS347 (2)
1506-347S31
17440 X6CrNiNb1810
G 4303 SUS316 (2)
1506-316S31
17440 X5CrNiMo17122
G 4303 SUS321 (2)
1506-321S31
17440 X6CrNiMTi1810
G 4107 SNB16
1506-670-860
17240 40CrMoV47
A-194 Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High-Temperature Service Gr 2H
G 4051 S45C (3)
1506-162
Gr 4 (C-Mo) Gr 6 (12Cr) Gr 8 (304) Gr 8MA (316)
-G 4303 SUS410 (3) G 4303 SUS304 (2) G 4303 Sus316 (2)
--1506-410S21-770 1506-304S31 1506-316S31
17240 C35 1654 Cq45 17240 24CrMo5 1654 X10Cr13 17440 X5CrNi1810 17440 X5CrNiMo17122
G 3101 SS400 (4)
4190-Gr 4,6
A-307 Carbon Steel Externally Threaded Standard Fasteners Gr B
G 4051 S25C (4)
17100 St44.2 17100 St44.3 17200 CK25 1654 Cq22
Note (1): Specify heat treatment and mechanical properties per ASTM. Note (2): Specify ASTH dimensional requirements, tolerances and inspection. Note (3): Specify mechanical properties, test and inspection in accordance with ASTM. Note (4):Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the steel.
STANDARD SPECIFICATION
ASTM A-320 Alloy Steel Bolting Materials for Low Temperature Service Gr L7 (Cr-Mo)
JIS
BS
G 4107 SNB7 (1)
1506-630-860
Gr L43 (Ni-Cr-Mo) Gr B8 (304 str.hd.) Gr B8C (347 str.hd.)
G 4103 SNCM439 G 4303 SUS304 (2) G 4303 SUS347 (2)
Gr B8T (321 str.hd.)
G 4303 SUS321 (2)
Gr B8M (316 str.hd.)
G 4303 SUS316 (2)
--1506-304S31 1506-347S31 970-347S31 1506-321S31 970-321S31 1506-316S31 970-316S31
DIN
17200 42CrMo4 17240 24CrMo5 --17440 X5CrNi1810 17440 X6CrNiNb1810 17440 X6CrNiTi1810 17440 X5CrNiMo17I22
A-325 High-Strength Bolts for Structure Steel Joints G 4051 S33C
3139
1654 Cq35
-----
-----
---
---
---
---
---
---
---
A-354 Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners Gr BC Gr BD A-453 Bolting Materials, High-Temperature , 50 to 120 KSI (345 to 827 Mpa) Yield Strength, with Expansion Coefficients Comparable to Austenitic Steels Gr 660 Class A & B (14Cr-24Ni) Gr 651 Class A & B (19Cr-9Ni)
Note (1): Specify Impact Test requirement per ASTM. Note (2): Specify ASTM dimensional requirements, tolerances and inspection.
STANDARD SPECIFICATION Table 7 BARS AND SHAPES
ASTM A-276 Stainless and Heat-Resisting Steel Bars and Shapes Type 420
JIS
BS
DIN
G4303 J1
970-420S37
17440 X20Cr13
Gr 1020 Gr 1025 Gr 1030 Gr 1035 Gr 1040 Gr 1045
G4051 S20C G4051 S25C G4051 S30C G4051 S35C G4051 S40C G4051 S45C
-------------
17200 CK22 17200 CK25 17200 CK30 17200 CK35 17200 CK40 17200 CK45
A-615 Deformed and Plain Billet-Steel Bars for Concrete Reinforcement Gr 40 Gr 60
G3112 SD295 G3112 SD390 (1)
Gr 250 (1) Gr 460/425 (1)
-488 BSt420S
Gr 45 Gr 50 Gr 55
G3101 SS330 G3101SS330 (1) G3101 SS400
Gr 40A (1) Gr 40A (1) Gr 40A (1)
Gr 60
G3101 SS400 (1)
Gr 43A
Gr 65 Gr 70 Gr 75 Gr 80
G3101 SS490 G3101 SS490 G3101 SS540 G3101 SS540 (1)
Gr 50A (1) Gr 55C or 50A (1) Gr 55C or 50A (1) Gr 55C (1)
17100 St33 17100 St33 17100 St44-2 17100 St44-3 17100 St44-2 17100 St44-3 17100 St52-3 17100 St52-3 -----
A-576 Steel Bars, Carbon, Hot-Wrought Special Quality
A-675 Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties
Note (1):
Recognize loser minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
STANDARD SPECIFICATION
Table 8 PIPING FITTINGS ASTM A-234 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and Elevated Temperatures WPB WPC WP1 (C-1/2Mo) WP5 (5Cr-1/2Mo) WP9 (9Cr-1/2Mo) WP11 (1-1/4Cr-1/2Mo) WP12 (1Cr-1/2Mo) WP22 (2-1/4Cr-1Mo)
A-403 Wrought Austenitic Stainless Steel Piping Fittings WP 304 (18Cr-8Ni) WP 304H(18Cr-8Ni) WP 304L (18Cr-8Ni) WP 316 (16Cr-12Ni-2Mo) WP 316H (16Cr-12Ni-2Mo) WP 316L (16Cr-12Ni-2Mo) WP 321 (18Cr-10Ni-Ti) WP 321H (18Cr-10Ni-Ti) WP 347 (18Cr-10Ni-Cb) WP 347H (18Cr-10Ni-Cb)
JIS
B 2312 PT410 6 2313 PT410W B 2312 PT480 B 2313 PT480W B 2312 PA12 B 2313 PA12W B 2312 PA25 B 2313 PA25W 8 2312 PA26 B 2313 PA-96W B 2312 PA23 B 2313 PA23W B 2312 PA22 B 2313 PA22W B 2312 PA24 8 2313 PA24W
B2312 SUS304 B2313 SUS304W B2312 SUS304H B2312 SUS304L B2313 SUS304LW B2312 SUS316 B2313 SUS316W B2312 SUS316H B2312 SUS316L B2313 SUS316LW B2312 SUS321 B2313 SUS321W B2312 SUS321H B2312 SUS347 B2313 SUS347W B2312 SUS347H
BS
DIN
1640 WPB
---
---
---
1640 WP1
---
1640 WP5
---
---
---
1640 WP11
---
---
---
1640 WP22
---
1640-WP304
---
--1640-WP304L
-----
1640-WP316
---
--1640-WP316L
-----
1640-WP321
---
--1640-WP347
-----
---
---
STANDARD SPECIFICATION
JIS A-420 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low Temperature Service WL3 (3-1/2Ni) WL6 WL8 (9Ni)
B 2312 PL450 B 2313 PL450W B 2312 PL380 B 2313 PL38OW B 2312 PL690
BS
DIN
1640-WPL3
---
1640-WPL0
---
---
---
STANDARD SPECIFICATION
Table 9 NONFERROUS MATERIALS ASTM
JIS
BS
DIN
PIPE B-42 Seamless Copper Pipe, Standards Sizes
H3300 C1020
2871-C103
1787 OF-Cu
B-43 Seamless Red Brass Pipe, Standard Sizes
H3300 C4430
---
17671 CuZn15
H4552 NCUT
3074
---
H4630 TTP28 H4630 TTP35 H4630 TTP49 ---
---------
17850 Ti1 17850 Ti2 17850 Ti3
G4903 NCF 800TP G4903 HCF 800HTP G4903 NCF 825TP
-------
-------
H3300 C7060 H3300 C7150
2871-CN102 2871-CN107
17664 CuNi10Fe1Mn 17664 CuNi30Mn1Fe
B-165 Nickel-Copper Alloy Seamless Pipe and Tube N04400 B-167 Nickel-Chromium-Iron Alloys Seamless Pipe and Tubes N06600
G4903 NCF600TP
B-337 Seamless and Welded Titanium and Titanium Alloy pipe Gr 1 Gr 2 Gr 3 Gr 7 B-407 Nickel-Iron-Chromium. Alloy Seamless Pipe and Tube N08800 N08810
B-466 Seamless Copper-Nickel Pipe and Tube C70600 C71500
STANDARD SPECIFICATION
ASTM B-467 Welded Copper-Nickel Pipe
JIS
BS
DIN
C70600 C71500
H3320 C7060 H3320 C7150
2871-CN102 2871-CN107
17664 CuNi10Fe1Mn 17664 CuNi30Mn1Fe
CASTINGS B-61 Steam or Valve Bronze Castings
H5111 BC7
1400-LG4
---
H5111 BC6
1400-LG2
1705 G-CuSn5ZnPb
B-62 Composition Bronze or Ounce Metal Castings
][® Austenitic stainless steel USA, Japan AISI grade
JIS grade
201
SUS 201
Europe UNS designation
S 201 00
EN / DIN numerical designation
EN / DIN symbolical designation
1.4372
X12CrMnNiN17-7-5
(EN)
QMS 5 202
SUS 202
S 202 00 S 209 10 S 215 00 S 245 65
219 301
X4CrNiMn21-9-6 SUS 301
S 301 00
302
SUS 302
S 302 00
1.4319
303
SUS 303
S 303 00
1.4305
(EN)
1.4301
(EN)
X6CrNi18-10
301 L
1.4310
(EN)
X10CrNi18-8
1.4318
(EN)
X2CrNiN18-7 X10CrNi18-9 X8CrNiS18-9
SUS 303 Cu SUS 303 HS2 SUS 303 HS3 303 Se
SUS 303 Se
S 303 23
304
SUS 304
S 304 00
X10CrNiS18-9
304 Cu
SUS XM 7
S 304 30
304 L
SUS 304 L
S 304 03
1.4306
(EN)
X2CrNi19-11
304 L
SUS 304 L
S 304 03
1.4307
(EN)
X2CrNi18-9
S 304 09
1.4948
S 304 15
1.4891
S 304 15
1.4818
SUS 304 ELC 304 H
SUS 304 H
X8CrNi19-10
SUS 304 Cu1 SUS 304 Cu2
304 N
SUS 304 N1
S 304 51
X5CrNiN18-10
SUS 304 N2 304 LN
SUS 304 LN
S 304 53
1.4311
(EN)
X2CrNiN18-10
S 305 00
1.4303
(EN)
X8CrNi18-12
S 306 00
1.4361
(EN)
X1CrNiSi18-15-4
SUS 304 MF 305
SUS 305 SUS 305 J1
F 46
S 306 15 308 309
S 309 00
1.4828
309
S 309 00
1.4829
X15CrNi23-13
309 S
SUS 309 S
S 309 08
1.4828
X15CrNiSi20-12
309 S
SUS 309 S
S 309 08
1.4833
X6CrNi22-13
309 S
SUS 309 S
X12CrNi23-13
S 309 08
1.4833
309 H
S 309 09
1.4833
309 Cb
S 309 40
www.weisz.com
Steel grades equivalence tables
Pág. 1
][® Austenitic stainless steel USA, Japan AISI grade
Europe
JIS grade
UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
310
1.4841
X15CrNiSi25-20
310
1.4845
X12CrNi25-20
309 HCb
S 309 41
SUS 310 ELC 310 L 310 L
1.4335
(EN)
X1CrNi25-21
1.4466
(EN)
X1CrNiMoN25-22-2
310 S
SUS 310 S
S 310 08
1.4842
310 S
SUS 310 S
S 310 08
1.4845
310 H
S 310 09
1.4845
310 Cb
S 310 40
310 HCb
S 310 41
310 HCbN
S 310 42
X6CrNi25-20 (EN)
X8CrNi25-21
310 SCB
F44
S 310 50
1.4465
X1CrNiMoN25-25-2
S 310 50
1.4466
(EN)
X1CrNiMoN25-22-2
S 312 54
1.4547
(EN)
X1CrNiMoCuN20-18-7 X5CrNiMo17-12-2
314
SUS 314
S 314 00
1.4841
316
SUS 316
S 316 00
1.4401
(EN)
316
SUS 316
S 316 00
1.4436
(EN)
X3CrNiMo17-13-3
S 316 40
1.4580
(EN)
X6CrNiMoNb17-12-2
316 Cb
X15CrNiSi25-20
316 F
SUS 316 F
S 316 20
1.4427
X6CrNiMoS18-11
316 L
SUS 316 L
S 316 03
1.4404
316 L
SUS 316 L
S 316 03
1.4406
316 L
SUS 316 L
S 316 03
1.4432
(EN)
X2CrNiMo17-12-3
316 L
SUS 316 L
S 316 03
1.4435
(EN)
X2CrNiMo18-14-3
316 L
SUS 316 L
S 316 03
1.4441
X6CrNiMo17-11
316 H
SUS 316 H
S 319 09
1.4919
X6CrNiMo17-12
S 316 51
(EN)
X2CrNiMo17-12-2 X2CrNiMoN17-11-2
SUS 316 J1 SUS 316 J1L 316 N
1.4406
(EN)
X2CrNiMoN17-11-2
316 LS
SUS 316 N
1.4436
(EN)
X3CrNiMo17-13-3
316 LS
1.4435
(EN)
X2CrNiMo18-14-3
316 LN
SUS 316 LN
S 316 53
1.4406
316 LN
SUS 316 LN
S 316 53
1.4429
316 LN
SUS 316 LN
S 316 53
1.3952
316 LN
SUS 316 LN
S 316 53
1.4910
316 Ti
SUS 316 Ti
S 316 35
1.4571
316 Ti
SUS 316 Ti
S 316 35
1.4573
317
SUS 317
S 317 00
X2CrNiMoN17-11-2 (EN)
X2CrNiMoN17-13-3 X2CrNiMoN18-14-3
316 S (EN)
X6CrNiMoTi17-12-2 X10CrNiMoTi17-13-3
SUS 317 J1
www.weisz.com
Steel grades equivalence tables
Pág. 2
][® Austenitic stainless steel USA, Japan AISI grade
JIS grade
317 L
SUS 317 L
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
S 317 03
1.4438
(EN)
X2CrNiMo18-15-4
317 L
S 317 03
1.4434
(EN)
X2CrNiMoN18-12-4
317 LM
S 317 25
317 LN
S 317 53
1.4439
(EN)
X2CrNiMoN17-13-5
317 LMN
S 317 26
1.4439
(EN)
X2CrNiMoN17-13-5
F 48
S 317 26
1.4439
(EN)
X2CrNiMoN17-13-5
(EN)
X6CrNiTi18-10
318 319 319 L 321
SUS 321
S 321 00
1.4541
321
SUS 321
S 321 00
1.4878
X12CrNiTi18-9
321 H
SUS 321 H
S 321 09
1.4878
X12CrNiTi18-9
321 H
SUS 321 H
S 321 09
1.4941
X7CrNiTi18-11
S 326 15 S 326 54 327
1.4821 S 327 50 S 328 03
333 S 332 28 347
SUS 347
S 347 00
1.4550
347 H
SUS 347 H
S 347 09
1.4961
348
S 348 00
1.4878
348 H
S 348 09
(EN)
X6CrNiNb18-10 X6CrNiNb18-12
347 HFG
S 353 15 926
1.4835 1.4529
21-6-9
S219 04
22-13-5
S 209 10
(EN)
X1NiCrMoCuN25-20-7
1.3964
X2CrNiMnMoNNb21-16-5-3
S 209 10
1.3964
X2CrNiMnMoNNb21-16-5-3
S 209 10
1.3974
X2CrNiMnMoNNb23-17-6-3
16-8-2H XM-10
S 219 00
XM-11
S 219 04
XM-15
S 381 00 SUS XM 15J1
XM-17
S 216 00
XM-18
S 216 03
XM-19 XM-19
SUS XM 19
XM-21
S 304 52
XM-29
S 240 00
XM-31
S 214 00
www.weisz.com
Steel grades equivalence tables
Pág. 3
][® Austenitic stainless steel USA, Japan AISI grade
JIS grade
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
1.4371
(EN)
X2CrMnNiN17-7-5
1.4373
(EN)
X12CrMnNiN18-9-5
1.4537
(EN)
X1CrNiMoCuN25-25-5
1.4577
X5CrNiMoTi25-25
1.4848 X6CrNiCu18-10-4Kd
High temperature austenitic stainless steel USA, Japan AISI grade
Alloy 286
www.weisz.com
JIS grade
Europe UNS designation
S 662 86
EN / DIN numerical designation
EN / DIN symbolical designation
1.4980
X5NiCrTi26-15
1.4961
X8CrNiNb16-3
1.4981
X8CrNiMoNb16-16
1.4988
X8CrNiMoVNb16-13
Steel grades equivalence tables
Pág. 4
][® Ferritic stainless steel USA, Japan AISI grade
JIS grade
405
SUS 405
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
S 409 00
1.4512
(EN)
X2CrTi12
S 410 08
1.4516
(EN)
X6CrNiTi12
1.4016
(EN)
X6Cr17
S 405 00
409 409 L SUS 410 LC 410 S 410 Ti
SUS 410 Ti
418 429
SUS 429
S 429 00
430
SUS 430
S 430 00
430 F
SUS 430 F
S 430 20
430 Cb
S 430 40
430 Ti
SUS 430 Ti
S 430 35
430 Ti
SUS 430 Ti
S 430 36
434
SUS 434
S 434 00
436
1.4511
X3CrNb17
1.4113
X6CrMo17-1
1.4536
439
(EN)
X3CrTi17
1.4509
(EN)
X2CrTiNb18
(EN)
X2CrMoTi18-2
S 430 35
1.4510
440 A
S 440 00
1.4522
440 B
S 440 00
439 L
441 442 443
SUS 443
S 443 00
444
QS 192
S 444 00
1.4521
446
SUH 446
S 446 00
1.4749
X18CrN28
455 490 501 XM-15 QS 25T XM-27
QS 261
XM-33
S 446 27 S 446 26
18-2
QS 192
S 444 00
1.4521
(EN)
X2CrMoTi18-2
19-3
QS 192
S 444 00
1.4521
(EN)
X2CrMoTi18-2
25-4-4
S 446 35
26-3-3
S 446 60
29-4
S 447 00
29-4C
S 447 35
29-4-2
S 448 00
P9
S 504 00 S 890 40 S 890 25
www.weisz.com
Steel grades equivalence tables
Pág. 5
][® Ferritic stainless steel USA, Japan AISI grade
Europe
JIS grade
UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
S 890 26 1.4000
(EN)
X6Cr13
1.4002
(EN)
X6CrAl13
1.4003
(EN)
X2CrNi12
1.4017
(EN)
X6CrNi17-1
1.4024
X15Cr13
1.4505 1.4506 1.4513
(EN)
X2CrMoTi17-1
1.4520
(EN)
X2CrTi17
1.4526
(EN)
X6CrMoNb17-1
1.4575 1.4590
(EN)
X2CrNbZr17
1.4592
(EN)
X2CrMoTi29-4
1.4605
(EN)
X2CrAlTi18-2
1.4724 Y 4L SIC 8 SIC 9 SIC 10 SIC 12
Heat resistant ferritic stainless steel USA, Japan AISI grade
www.weisz.com
JIS grade
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
1.4713
X10CrAl7
1.4742
X10CrAl18
1.4781
X10CrAl24
Steel grades equivalence tables
Pág. 6
][® Duplex (ferritic / austenitic) stainless steel USA, Japan AISI grade
JIS grade
2205
QS 2205
Europe UNS designation
S 318 03
EN / DIN numerical designation
EN / DIN symbolical designation
1.4462
(EN)
X2CrNiMon22-5-3
1.4462
(EN)
X2CrNiMoN22-5-3
(EN)
X2CrNiMoN25-7-4
(EN)
X2CrNiMoCuN25-6-3
2205
S 322 05
2304
S 323 04
2506
S 312 60
2507
S 327 50
1.4410
S 325 50
1.4460
S 325 50
1.4507
S 312 00
1.4460
S 318 03
1.4462
(EN)
X2CrNiMoN22-5-3
1.4410
(EN)
X2CrNiMoN25-7-4
1.4501
(EN)
X2CrNiMoCuWN25-7-4
2550 2550
QSA 2505
F 50 F 51
QS 2205
F 51
S 322 05
F 52
S 329 50
F 53
S 327 50
F 54
S 327 40
F 55
S 327 60
X3CrNiMoN27-5-2
S 312 54 QS 1905
S 315 00
1.4417
X2CrNiMoSi19-5
S 317 60 329
SUS 329 J1
S 329 00
SUS 329 J2L 4462 1.4362
(EN)
X2CrNiN23-4
S 392 74
www.weisz.com
Steel grades equivalence tables
Pág. 7
][® Martensitic stainless steel USA, Japan AISI grade
JIS grade
403
SUS 403
410
SUS 410
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
S 410 00
1.4006
(EN)
X12Cr13
S 410 08
1.4006
(EN)
X12Cr13
S 410 50
1.4030
S 415 00
1.4313
(EN)
X3CrNiMo13-4
S 420 00
1.4021
(EN)
X20Cr13
S 420 10
1.4021
(EN)
X20Cr13
S 420 00
1.4028
(EN)
X30Cr13
S 403 00 S 408 00
414 SUS 410 J1 410 S F6NM 416
SUS 416
S 416 00
SUS 416 HS2 SUS 416 L 416Se 420 420
SUS 420 J1 SUS 420 J2 SUS 420 J2C SUS 420 J2L
420 F
SUS 420 F
F3NM
S 420 20 S 424 00
1.4320
X2CrNiMo13-4
SUS 429 J1 431
SUS 431
440 A 440 C
S 431 00 S 440 00
SUS 440 C
S 440 04
SUS 440 F XM 12
S 155 00
1.4545
X5CrNiCuNb15-5-4
1.4031
(EN)
X39Cr13
1.4034
(EN)
X46Cr13
1.4116
(EN)
X50CrMoV15
1.4122
(EN)
X39CrMo17-1
1.4418
(EN)
X4CrNiMo16-5-1
1.4922
X20CrMoV12-1
1.4935
X20CrMoWV12-1
QD 51 QPD 5 Y 2L Y 2LF
www.weisz.com
Steel grades equivalence tables
Pág. 8
][® High temperature martensitic stainless steel USA, Japan AISI grade
JIS grade
Europe UNS designation
F 91
EN / DIN numerical designation
EN / DIN symbolical designation
1.4903
X10CrMoVNb9-1
1.4913
X19CrMoVNbN11-1
1.4922
X20CrMoV12-1
Antimagnetic stainless steel USA, Japan AISI grade
JIS grade
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
1.3951
X2CrNiMoN22-15
QMR 1L QMR 2L QMR 3L QMR 4L QMR 5L
www.weisz.com
Steel grades equivalence tables
Pág. 9
][® Precipitation hardening stainless steel USA, Japan AISI grade
Europe
JIS grade
UNS designation
630 631
S 174 00 SUS 631
EN / DIN numerical designation
EN / DIN symbolical designation
1.4532
(EN)
X8CrNiMoAl15-7-2
1.4542
(EN)
X5CrNiCuNb16-4
1.4568
(EN)
X7CrNiAl17-7
S 177 00
16-6 PH AM 350 AM 355 Alloy 15-5 PH Alloy 17-4 PH Alloy 17-7 PH Alloy 718 USS Stainless W
High molybdenum alloy USA, Japan AISI grade
Europe
JIS grade
UNS designation
Alloy 29-4
EN / DIN numerical designation
EN / DIN symbolical designation
S 447 35
Alloy 29-4-2 Alloy 254 SMO
S 312 54
1.4547
(EN)
X1CrNiMoCuN20-18-7
Alloy 256 MO
N 08 926
1.4529
(EN)
X1NiCrMoCuN25-20-7
Alloy 654 SMO
S 326 54
1.4652
N 08 904
1.4539
(EN)
X1NiCrMoCu25-20-5
Alloy 904 L
QS 2025 MC
Alloy 1925 HMO
N 08 925
Alloy C-276
N 10 276
Alloy C-1008 Alloy C-1010 Alloy F 49
S 345 65 QS 2025 MT
1.4565
X3CrNiMnMoNbN23-17-5-3
N 08 320 1.4583
X6CrNiMoN18-12 X1NiCrMoCuN20-18-7
www.weisz.com
Steel grades equivalence tables
Pág. 10
][® High nickel alloy USA, Japan AISI grade
JIS grade
Europe UNS designation
QS 20 Cb3
N 08 020
QS 2830
N 08 028
EN / DIN numerical designation
EN / DIN symbolical designation
1.4563
X1NiCrMoCu31-27-4
(EN)
N 08 310 N 05 500
2.4375
Alloy B2
N 10 665
Alloy C4
N 06 455
Alloy CP Gr2
R 50 400
Alloy C22
N 06 022
2.4602
2.4610
N 06 059
2.4605
Alloy C-276
QA C276
N 10 276
2.4819
Alloy G
QA G
N 06 007 N 06 617
Alloy G-3
QA G3
Alloy G-30
2.4663
N 06 985 N 06 030
Alloy K-500 Alloy L-605
R 30 605
Alloy HX Alloy MP35N Alloy X
QA X
N 06 002
Alloy X-750 Alloy 6AC Alloy 6XN
N 08 367
Alloy 20 Alloy 25 Alloy 31
N 08 031
1.4562
Alloy 41XX Alloy 42 Alloy 43XX Alloy 52 Alloy 59
N 06 059
Alloy 188 Alloy 205 Alloy 220 Alloy 222 Alloy 230 Alloy 253 RMA Alloy 400
QA 400
N 04 400
2.4360
NiCu30
Alloy 600
NCF 600
N 06 600
2.4816
NiCr15Fe
Alloy 600
NCF 600
N 06 600
2.4640
NiCr15Fe
Alloy 601
NCF 601
N 06 601
2.4851
NiCr23Fe
Alloy 556
www.weisz.com
Steel grades equivalence tables
Pág. 11
][® High nickel alloy USA, Japan AISI grade
JIS grade
Europe UNS designation
Alloy 602
EN / DIN symbolical designation
2.4633
Alloy 622 Alloy 625
EN / DIN numerical designation
N 06 622 QA 625
N 06 625
2.4856
N 06 690
2.4642
NiCr29Fe
N 07 718
2.4668
NiCr19NbMo
N 08 800
1.4558
X2NiCrAlTi32-20
Alloy 686 Alloy 690 JS 700
QS 2025 M
Alloy 718 Alloy 800
NCF 800
Alloy 800
N 08 700
N 08 800
1.4958
X5NiCrAlTi31-20
Alloy 800
NCF 800
N 08 800
1.4876
X10NiCrAlTi32-20
Alloy 800 H
NCF 800 H
N 08 810
1.4958
X8NiCrAlTi32-21
N 08 811
1.4959
X8NiCrAlTi32-21
N 08 825
2.4858
NiCr21Mo
CuNi10Fe
Alloy 800 HT Alloy 825
NCF 825
N 08 840 Alloy 902 Cupronickel 10
C 706 00
2.0872
Cupronickel 30
C 715 00
2.0882
CuNi30Mn1Fe
1.4864
X12NiCrSi36-16
Alloy 330
1.4877 2.4973
NiCr19CoMo
High temperature alloy USA, Japan AISI grade
JIS grade
Europe UNS designation
Alloy A 286
S 662 86
Alloy MP-35N
R 30 035
Alloy X 750
N 07 750
Alloy 102
N 06 102
Alloy 253MA or F45
S 308 15
Alloy 330
N 08 330
Alloy 333
N 06 333
Alloy 617
N 06 617
www.weisz.com
EN / DIN numerical designation
EN / DIN symbolical designation
1.4835
Steel grades equivalence tables
Pág. 12
][® Metals USA, Japan AISI grade
JIS grade
Europe UNS designation
EN / DIN numerical designation
EN / DIN symbolical designation
Titanium 3Al 2.5V Titanium Beta C Titanium Gr 1
3.7025
Titanium Gr 2
3.7035
Titanium Gr 3
3.7055
Titanium Gr 4 Titanium Gr 7
3.7235
Titanium Gr 11
3.7225
Titanium Cr 12 Titanium T40 Titanium T40 Gr2 Zircaloy 1 Zircaloy 2 Zirconium Zirconium 2.5Nb Hafnium Copper Nickel 200
Ni 200
N 02 200
2.4060
Nickel 201
Ni 201
N 02 201
2.4061
Nickel 200
N 02 200
2.4066
Nickel 201
N 02 201
2.4068
Nickel 270
www.weisz.com
Steel grades equivalence tables
Pág. 13
MARYLAND METRICS Technical Data Chart
A short general listing of popular materials
International Material Grade Comparison Table
The standards that correspond with DIN Material Numbers can only be compared approximately. The use of these equivalents has to be evaluated on a case-by-case basis.
Steel Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
Plain Steel, Cast Steel, Free-Machining Steel 1.0332
St14
1008
1.1121
Ck10
1010
1.0721
10S20
1108
1.0401
C15
1015
CC12
080M15
C15C16
1350
F.111
1.0402
C22
1020
CC20
050A20
C20C21
1450
F.112
1.1141
Ck15
1015
XC12
080M15
C16
1370
C15K
1.0036
USt37-3
CC10
14491CR
1447
040A10
1264
S10C
210M15 S15C S15C
FE37BFU
1.0715
9SMn28
1213
S250
1.0718
9SMnPb28
12L3
S250Pb
230M07
CF9SMn28
1912
11SMn28
SUM22
CF9SMnPb28
1914
11SMnPb28
SUM22L
1.0501
C35
1035
CC35
060A35
C35
1550
F.113
S35C
1.0503
C45
1045
CC45
080M46
C45
1650
F.114
S45C
1.1158
Ck25
1025
XC25
070M25
C25
S25C
1.1183
Cf35
1035
XC38TS
060A35
C36
1572
1.1191
Ck45
1045
XC42
080M46
C45
1672
1.1213
Cf53
1050
XC48TS
060A52
C53
1674
1.5415
15Mo3
ASTMA204GrA
15D3
1501-240
16Mo3KW
2912
1.5423
16Mo5
4520
1503-245-420
16Mo5
1.0050
St50-2
1.7242
16CrMo 4
1.7337
16CrMo 4 4
1.7362
12CrMo 19 5
1.0060
St60-2
1.0535
C55
S35C C45K
S50C 16Mo3 16Mo5
FE50 18CrMo4
S45C
SB450M SM50YA
18CrMo4
A387Gr.12Cl.
A18CrMo45KW Z10CD5.05
3606-625
16CrMo205 FE60-2
1055
070M55
C55
SM570 1655
S55C
1.0601
C60
1060
CC55
080A62
C60
1.1203
Ck55
1055
XC55
070M55
C50
1.1221
Ck60
1060
XC60
080A62
C60
1.1545
C1051
C100KU
SK3
1.1545
C105W1
C100KU
SK3
1.0070
St70-2
FE70-2
1.7238
49CrMo4
1.7561
42CrV6
1.7701
51CrMoV4
51CDV4
S60C C55K 1678
S55C S58C
51CrMoV4
Low-Alloy Steel, Cast Steel, Free-Machining Steel 1.2067
100Cr6
L3
Y100C6
BL3
1.2210
115CrV3
L2
100C3
107CrV3KU
1.2241
51CrV4
1.2419
105WCr6
105WC13
10WCr6
2140
100Cr6
SUJ2
105WCr5
SKS31
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
1.2419
105WCr6
1.2542
45WCrV7
S1
1.2550
60WCrV7
S1
55WC20
1.2713
55NiCrMoV6
L6
55NCDV7
1.2721
50NiCr13
1.2762
75CrMoNiW67
1.2762
75CrMoNiW67
1.2842
90MnCrV8
1.3505 1.5622 1.5732
14NiCr10
3415
14NC11
1.5752
14NiCr14
3415;3310
12NC15
655M13
1.6511
36CrNiMo4
9840
40NCD3
816M40
38NiCrM04(KB)
1.6523
21NiCrMo2
8620
20NCD2
805M20
20NiCrMo2
1.6546
40NiCrMo22
8740
1.6582
35CrNiMo6
4340
105WC13
107WCr5KU BS1
Japan JIS SKS31
45WCrV8KU
2710
58WCr9KU
~2710
45WCrSi8 F.520.S
SKH1;SKT4
~2550
O2
90MV8
BO2
88MnV8KU
100Cr6
52100
100C6
534A99
100Cr6
14Ni6
ASTMA350LF5
16N6
1.6587
17CrNiMo6
1.6657
14NiCrMo34
1.7033
34Cr4
5132
1.7035
41Cr4
1.7045
42Cr4
1.7131
16MnCr5
35NCD6 18NCD6
2258 15Ni6
16NiCr11
15NiCr11
SNC415(H) SNC815(H)
311-TYPE7
40NiCrM02(KB)
817M40
35NiCrMo6(KB)
2506
33NiCrMo4
SNCM447
20NiCrMo2
SNCM220(H)
40NiCrMo2 2541
820A16 832M13
SUJ2
14Ni6
SNCM240 SNCM447
14NiCrMo13 15NiCrMo13
14NiCrMo131
32C4
530A32
34Cr4(KB)
35Cr4
SCR430(H)
5140
42C4
530M40
5140
42C4TS
530A40
41Cr4
2245
42Cr4 42Cr4
SCR440(H) SCr440
5115
16MC5
(527M20)
16MnCr5
2511
16MnCr5
SCR415
1.7176
55Cr3
5155
55C3
527A60
1.7218
25CrMo4
4130
25CD4
1717CDS110
25CrMo4(KB)
2225
55Cr3
SM420;SCM430
SUP9(A)
1.7220
34CrMo4
4137;4135
35CD4
708A37
35CrMo4
2234
34CrMo4
SCM432;SCCRM3
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
Plain Steel, Cast Steel, Free-Machining Steel 1.0332
St14
1008
1.1121
Ck10
1010
1.0721
10S20
1108
1.0401
C15
1015
CC12
080M15
C15C16
1350
F.111
S15C
1.0402
C22
1020
CC20
050A20
C20C21
1450
F.112
S20C,S22C
1.1141
Ck15
1015
XC12
080M15
C16
1370
C15K
S15C
1.0036
USt37-3
CC10
14491CR
1447
040A10
1264
S10C
210M15
FE37BFU
1.0715
9SMn28
1213
S250
1.0718
9SMnPb28
12L3
S250Pb
230M07
CF9SMn28
1912
11SMn28
SUM22
CF9SMnPb28
1914
11SMnPb28
SUM22L
1.0501
C35
1035
CC35
060A35
C35
1550
F.113
S35C
1.0503
C45
1045
CC45
080M46
C45
1650
F.114
S45C
1.1158
Ck25
1025
XC25
070M25
C25
S25C
1.1183
Cf35
1035
XC38TS
060A35
C36
1572
1.1191
Ck45
1045
XC42
080M46
C45
1672
1.1213
Cf53
1050
XC48TS
060A52
C53
1674
S35C C45K
S45C S50C
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
1.5415
15Mo3
ASTMA204GrA
15D3
1501-240
16Mo3KW
2912
16Mo3
1.5423
16Mo5
4520
1503-245-420
16Mo5
1.0050
St50-2
1.7242
16CrMo 4
1.7337
16CrMo 4 4
1.7362
12CrMo 19 5
1.0060
St60-2
1.0535
C55
16Mo5
FE50 18CrMo4
SB450M SM50YA
18CrMo4
A387Gr.12Cl.
A18CrMo45KW Z10CD5.05
3606-625
16CrMo205 FE60-2
1055
070M55
C55
SM570 1655
S55C
1.0601
C60
1060
CC55
080A62
C60
1.1203
Ck55
1055
XC55
070M55
C50
1.1221
Ck60
1060
XC60
080A62
C60
1.1545
C1051
C100KU
SK3
1.1545
C105W1
C100KU
SK3
1.0070
St70-2
FE70-2
1.7238
49CrMo4
1.7561
42CrV6
1.7701
51CrMoV4
51CDV4
S60C C55K 1678
S55C S58C
51CrMoV4
Low-Alloy Steel, Cast Steel, Free-Machining Steel 1.2067
100Cr6
L3
Y100C6
BL3
100Cr6
1.2210
115CrV3
L2
100C3
1.2241
51CrV4
1.2419
105WCr6
105WC13
10WCr6
1.2419
105WCr6
105WC13
107WCr5KU
1.2542
45WCrV7
S1
1.2550
60WCrV7
S1
55WC20
1.2713
55NiCrMoV6
L6
55NCDV7
1.2721
50NiCr13
1.2762
75CrMoNiW67
1.2762
75CrMoNiW67
1.2842
90MnCrV8
1.3505 1.5622 1.5732
14NiCr10
3415
14NC11
1.5752
14NiCr14
3415;3310
12NC15
655M13
1.6511
36CrNiMo4
9840
40NCD3
816M40
38NiCrM04(KB)
1.6523
21NiCrMo2
8620
20NCD2
805M20
20NiCrMo2
1.6546
40NiCrMo22
8740
1.6582
35CrNiMo6
4340
SUJ2
107CrV3KU
BS1
2140
105WCr5
SKS31 SKS31
45WCrV8KU
2710
58WCr9KU
~2710
45WCrSi8 F.520.S
SKH1;SKT4
~2550
O2
90MV8
BO2
88MnV8KU
100Cr6
52100
100C6
534A99
100Cr6
14Ni6
ASTMA350LF5
16N6
1.6587
17CrNiMo6
1.6657
14NiCrMo34
1.7033
34Cr4
5132
1.7035
41Cr4
1.7045
42Cr4
1.7131
16MnCr5
35NCD6 18NCD6
2258 15Ni6
16NiCr11
15NiCr11
SNC415(H) SNC815(H)
311-TYPE7
40NiCrM02(KB)
817M40
35NiCrMo6(KB)
2506
33NiCrMo4
SNCM447
20NiCrMo2
SNCM220(H)
40NiCrMo2 2541
820A16 832M13
SUJ2
14Ni6
SNCM240 SNCM447
14NiCrMo13 15NiCrMo13
14NiCrMo131
32C4
530A32
34Cr4(KB)
35Cr4
SCR430(H)
5140
42C4
530M40
5140
42C4TS
530A40
41Cr4
2245
42Cr4 42Cr4
SCR440(H) SCr440
5115
16MC5
(527M20)
16MnCr5
2511
16MnCr5
SCR415
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
Japan
1.7176
55Cr3
5155
55C3
527A60
1.7218
25CrMo4
4130
25CD4
1717CDS110
25CrMo4(KB)
2225
55Cr3
SM420;SCM430
1.7220
34CrMo4
4137;4135
35CD4
708A37
35CrMo4
2234
34CrMo4
SCM432;SCCRM3
JIS SUP9(A)
Plain Steel, Cast Steel, Free-Machining Steel 1.7223
41CrMo4
4140;4142
42CD4TS
708M40
41CrMo4
2244
42CrMo4
SCM440
1.7225
42CrMo4
4140
42CD4
708M40
42CrMo4
2244
42CrMo4
SCM440(H)
12CrMo4
SCM415(H)
ASTMA182
15CD3.5/4.5
1501-620-Gr27
14CrMo45
14CrMo45
SPVAF12
722M24
32CrMo12
2240
735A50
50CrV4
2230
735A50
51CrV4
2230
1.7262
15CrMo5
1.7335
13CrMo4 4
12CD4
1.7361
32CrMo12
1.7380
10CrMo9 10
1.7715
14MoV6 3
1.8159
50CrV4
6150
1.8159
50CrV4
6150
1.3501
100Cr2
E50100
100C2
1.5710
36NiCr6
3135
35NC6
1.5736
36NiCr10
3435
30NC11
1.5755
31NiCr14
SNC836
1.7733
24CrMoV55
1.7755
GS-45CrMoV104
1.8070
21CrMoV511
1.8509
41CrALMo7
1.8523
39CrMoV139
1.2311
40CrMnMo7
1.4882
X50CrMnNiNbN219
1.5864
35NiCr18
30CD12 ASTMA182F.22 SPV
2216
F.124.A
1501-622Gr31;45 1503-660-440 50CrV4
18NC13
13MoCrV6 51CrV4
SUP10 SUP10
640A35
SNC236 SNC631(H)
653M31
20CDV6
21CrMoV511 35NiCr9
SACM645
40CAD6,12
905M39
41CrAlMo7
897M39
36CrMoV12
2940
41CrAlMo7
X37CrMoV5
SKD6
2242
X40CrMoV5
SKD61
2312
X210CrW12
SKD2
X30WCrV9
SKD5
2310
X160CrMoV12
35CrMo8KU Z50CMNNb21.09
High-Alloy Steel, Cast Steel 1.2343
X38CrMoV51
H11
Z38CDV5
BH11
X37CrMoV51KU
1.2344
X40CrMoV51
H13
Z40CDV5
BH13
X40CrMoV511KU
1.2379
X155CrVMo121
D2
Z160CDV12
BD2
X155CrVMo121KU
1.2436
X210CrW12
X215CrW121KU
1.2581
X30WCrV93
1.2601
X 165CrMoV12
H21
1.2606
X37CrMoW 51
H12
1.5662
X8Ni9
ASTMA353
1.5680
12Ni19
2515
1.3202
S12-1-4-5
1.3207
S10-4-3-10
1.3243
S6-5-2-5
Z30WCV9
BH21
X30WCrV93KU X165CrMoW12KU
Z35CWDV5
BH12
X35CrMoW05KU
F.537
SKD62
1501.509; 50
X10Ni9
XBNi09
SL9N53
BT15
HS12-1-5-5
12-1-5-5
BT42
HS10-4-3-10
Z18N5 Z130WKCDV
T15
SKD11
KCV06-05-05-04-02
HS6-5-2-5
SKH57 2723
1.3246
S7-4-2-5
Z110WKCDV07-05-04
1.3247
S2-10-1-8
Z110DKCWV09-08-04
1.3249
S2-9-2-8
M42
1.3343
S6-5-2
M35
Z85WDCV
BM2
HS6-5-2-5
2722
403
Z6C13
403S17
X6Cr3
2301
BM42
6-5-2-5
HS7-4-2-5
7-4-2-5
M35
HS2-9-1-8
2-10-1-8
M41
BM34
SKH55 SKH51
2-9-2-8 SKH9; SKH51
Stainless Steel, Cast Steel 1.4000
X6Cr13
F.3110
SUS403
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
1.4001
X6Cr14
F.8401
410S, 429 SUS410
1.4002
X6CrAl13
405
Z8CA12
405S17
X6CrAl13
1.4006
(G-)X10Cr13
SUS410
Z10C13
410S21
X12Cr13
2302
F.3401
1.4016
X8Cr17
430
Z8C17
430S15
X8Cr17
2320
F.3113
1.4021
X20Cr13
420
Z20C13
420S37
X20Cr13
2303
Z20C13M
420C29
Japan
SUS405 SUS430 SUS420J1
1.4027
G-X20Cr14
1.4086
G-X120Cr29
1.4104
X12CrMoS17
430F
Z10CF17
441S29
X10CrS17
2383
1.4113
X6CrMo17
434
Z8CD1701
434S17
X8CrMo17
2325
1.4340
G-X40CrNi274
1.4417
X2CrNiMoSi195
1.4720
X20CrMo13
1.4724
X10CrA113
405
Z10C13
403S17
X10CrA112
F.311
SUS405
1.4742
X10CrA118
430
Z10CAS18
430S15
X8Cr17
F.3113
SUS430
1.4762
X10CrA124
446
Z10CAS24
1.4034
X46Cr13
1.4057
X20CrNi17
1.4125
X105CrMo17
SCS2
452C11
S31500
431
F.3117
SUS430F SUS434
2376
Z40CM
420S45
Z6CNi6.02
431S29
Z100CD17
X16Cr26
2322
X40Cr14
2304
X16CrNi16
2321
SUH446 F.3405 SUS431
X 105CrMo17
SUS440C
Stainless Steel and Cast Iron Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS SUS304
Austenitic Stainless Steel 1.4301
X5CrNi189
304
Z6CN18.09
304S15
X5CrNi1810
2332
F.3551
1.4310
X12CrNi177
301
Z12CN17.07
301S21
X2CrNi1807
2331
F.3517
1.4311
X2CrNiN1810
304LN
Z2CN18.10
304S62
X2CrNiN1810
2371
1.4312
G-X10CrNi188
Z10CN18.9M
302C25
1.4350
X5CrNi189
304
Z6CN18.09
304S31
X5CrNi1810
2332/2333
1.4362
X2CrNiN234
S32304
Z2CN23-04AZ
1.4401
X5CrNiMo17122
316
Z6CND17.11
316S16
X5CrNiMo1712
2347
1.4404
X2CrNiMo1810
316L
Z2CND17.12
316S12
X2CrNiMo1712
2343/2348/2553
SUS316
1.4410
G-X10CrNiMo189
1.4429
X2CrNiMoN17133
316LN
Z2CND17.13
316S63
X2CrNiMoN1713
2375
SUS316LN
1.4435
X2CrNiMo18143
316L
Z2CND17.12
316S13
X2CrNiMo1712
2353
SCS16
1.4436
X5CrNiMo17133
316
Z6CND18-12-03
316S33
X8CrNiMo1713
2343/2347
SUS316
1.4438
X2CrNiMo18164
317L
Z2CND19.15
317S12
X2CrNiMo1816
2367
SUS317L
1.4500
G-X7NiCrMoCuNb2520
1.4541
X10CrNiMoTi1810
321
Z6CNT18.10
321S12
X6CrNiTi1811
2337
F.3553F.3523
SUS321
1.4550
X10CrNiNb
347
Z6CNNb18.10
347S17
X6CrNiNb1811
2338
F.3552F.3524
SUS347
X6CrNiMoTi1712
2350
F.3535
SUS316TI
SUS301 SUS304LN
F.3551
2327 F.3543
SUS316
Z5CND20.12M
23NCDU25.20M
1.4552
G-X7CrNiNb189
Z4CNNb19.10M
347C17
1.4571
X10CrNiMoTi1810
316Ti
Z6NDT17.12
320S17
1.4583
X10CrNiMoNb1812
318
Z6CNDN1713B
1.4585
G-X7CrNiMoCuNb1818
1.4828
X15CrNiSi2012
X6CrNiMoNb X6CrNiMoTi1712
309
Z15CNS20.12
309S24
SUH309
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
Japan JIS
1.4845
X12CrNi2521
310S
Z12CN2520
310S24
X6CrNi2520
2361
F.331
SUH310; SUS310S
Austenitic/Ferritic Stainless Steel (Duplex) 1.4460
X8CrNiMo275
1.4462
X2CrNiMoN2253
S32900 Z2CND22-05-03
2324
1.4821
X20CrNiSi254
Z20CNS25.04
1.4823
G-X40CrNiSi274
SUS329J1
2977
Gray Cast Iron 0.6010
GG10
CLASS20
Ft10D
G10
110
0.6015
GG15
CLASS25
Ft15D
0.6020
GG20
CLASS30
Ft20D
0.6025
GG25
CLASS35
0.6030
GG30
0.6035 0.6040
FC100
GRADE150
G15
115
FG15
FC150
GRADE220
G20
120
FG20
FC200
Ft25D
GRADE260
G25
125
FG25
FC250
CLASS45
Ft30D
GRADE300
G30
130
FG30
FC300
GG35
CLASS50
Ft35D
GRADE350
G35
135
FG35
FC350
GG40
CLASS55
Ft40D
GRADE400
60-40-18
FCS400-12
SNG420/12
FGS370-17
SNG370/17
80-55-06
FGS500-7
SNG500/7
FGS600-3
SNG600/3
GGG60
0732-03
GGG60
FCD600
100-70-03
FGS700-2
SNG700/2
GGG70
0737-01
GGG70
FCD700
MB40-10
W410/4
GMB40
GTW40
GMB45
GTW45
140
FC400
Gray Cast Iron with Nodular Graphite 0.7033
GGG35.3
0.7040
GGG40
0.7043
GGG40.3
0.7050
GGG50
0.7060
GGG60
0.7070
GGG70
0717-15 GGG40
0717-02
FCD350 GGG40
0717-12 GGG50
0727-02
FCD400 FCD400
GGG50
FCD500
White malleable Cast Iron 0.8040
GTW-40
0.8045
GTW-45
0.8055
GTW-55
0.8065
GTW-65
0.8135
GTS-35
32510
0.8145
GTS-45
40010
0.8035
GTW-35
0.8155
GTS-55
0.8165 0.8170 Werkstoff
Germany
No.
DIN
3.0255
Al99.5
1000
3.3315
AlMg1
GTW55 GTW65 MN35-10
B340/12
810
P440/7
852
GTS35 GTS45
MB35-7
W340/3
GTW35
50005
MP50-5
P510/4
GTS-65
70003
MP60-3
P570/3
856
GTS65
GTS-70
90001
M870-2
P690/2
0862; 0864
GTS70
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
A59050C
L31/34/36
3.4345
AlZnMgCu0,5
AZ4GU/9051
L86
811-04
7050
854
GTS55
Non-Ferrous Materials Aluminium Alloys
3.1655
AlCuSiPb
3.1754
G-AlCu5Ni1,5
3.2373
G-AlSi9Mg
3.2381
G-AlSi10Mg
3.2382
GD-AlSi10Mg
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
3.2383
G-AlSi10Mg (Cu)
A360.2
LM9
4253
3.2383
GK-AlSi10Mg (Cu)
A360.2
LM9
4253
3.2581
G-AlSi12
A413.2
LM6
4261
3.2582
GD-AlSi12
A413.0
3.2583
G-AlSi12 (Cu)
A413.1
3.3561
G-AlMg5
GD-AlSi12
3.5101
G-MgZn4SE1Zr1
ZE41
3.5103
MgSE3Zn2Zr1
3.5106 3.5812
4247
A6061
LM20
4260
ADC12
A-SU 12
LN5
4252
AC4A
G-Z4TR
MAG5
EZ33
G-TR3Z2
MAG6
G-MgAg3SE2Zr1
QE22
G-Ag22,5
MAG12
G-MgAl8Zn1
AZ81
G-A9
MAG1
3.5912
G-MgAl9Zn1
AZ91
G-A9Z1
MAG7
2.1871
G-AlCu4TiMg
3.2371
G-AlSi7Mg
4218B
2.1090
G-CuSn7ZnPb
C93200
U-E7Z5Pb4
2.1096
G-CuSn5ZnPb
C83600
U-E5Pb5Z5
LG2
2.1098
G-CuSn2ZnPb
2.1176
G-CuPb10Sn
C93700
U-E10Pb10
LB2
2.1182
G-CuPb15Sn
C93800
U-Pb15E8
LB1
2.0240
CuZn15
C23000
CuZn15
CZ102
2.0265
CuZn30
C26000
CuZn30
CZ106
2.0321
CuZn37
C27200, C27700
CuZn36, CuZn37
CZ108
2.0592
G-CuZn35Al1
C86500
U-Z36N3
HTB1
2.0596
G-CuZn34Al2
C86200
U-Z36N3
HTB1
2.1188
G-CuPb20Sn
C94100
U-Pb20
2.1292
G-CuCrF35
C81500
Copper Alloys
C2700,C2720
LB5 CC1-FF
2.1293
CuCrZr
C18200
U-Cr0,8Zr
CC102
2.0966
CuAl10Ni5Fe4
C63000
U-A10N
Ca104
2.0975
G-CuAl10Ni
B-148-52
2.1050
G-CuSn10
C90700
2.1052
G-CuSn12
C90800
CT1 UE12P
Pb2
High-Temp Alloys Werkstoff
Germany
U.S.A.
France
Great Britain
US
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
US Trade Designation
SS
UNE
JIS
NA15
Incoloy 800
Super-Alloys Fe-based 1.4558
X2NiCrAlTi3220
N08800
1.4562
X1NiCrMoCu32287
N08031
1.4563
X1NiCrMoCuN31274
N08028
Z1NCDU31.27
1.4864
X12NiCrSi
330
Z12NCS35.16
1.4864
X12NiCrSi3616
N08330
Z12NCS35.16
1.4958
X5NiCrAlTi3120
1.4977
X40CoCrNi2020
Z42CNKDWNb
SUH330 NA17
SUH330
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
S66286
A-286
S41800
Greek Ascoloy
R30556
Haynes 556 (HS556)
R30155
N155
Super-Alloys Co-based R30188
Haynes 188
R30605
L605 (Haynes 25) MARM-302, 322, 509 Stellite 6, 21, 31
Super-alloys Ni-based 2.4360
NiCu30Fe
2.4610
NiMo16Cr16Ti
2.4630
NiCr20Ti
2.4642
NiCr29Fe
NU30
NA13
Monel 400 Hastelloy C-4
N06075
NC20T
HR5, 203-4
NC30Fe
Nimonic 75 Inconel 690
2.4810
G-NiMo30
N10276
2.4856
NiCr22Mo9Nb
N06625
NC22FeDNb
Hastelloy C
2.4858
NiCr21Mo
N08825
NC21FeDU
NA16
Incoloy 825
2.4375
NiCu30 Al
NU30AT
NA18
Monel K-500
2.4668
NiCr19FeNbMo
2.4669 2.4685 2.4694
NA21
Inconel 625
N07718
NC19FeNb
Inconel 718
NiCr15Fe7TiAl
N07750
NC15TNbA
Inconel X-750
G-NiMo28
N10001
Hastelloy B
NiCr16Fe7TiAl
N00751
Inconel 751
Titanium and titanium alloys 3.7025
Ti 1
3.7124
TiCu2
3.7195
TiAl3V2.5
R50250
2TA1 2TA21-24
3.7225
Ti1Pd
3.7115
TiAl5Sn2
R52250
3.7145
TiAl6Sn2Zr4Mo2Si
R54620
3.7165
TiAl6V4
R56400
3.7175
TiAl6V6Sn2
R56620
3.7185
TiAl4Mo4Sn2
TP1
T-A6V
TA10-13; TA28
TiAl6V4 Ti6V6Al2Sn
TA45-51; TA57
Hardened Materials Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
0.9620
G-X260NiCr42
Ni- Hard 2
Grade 2A
0512-00
0.9625
G-X330NiCr42
Ni- Hard 1
Grade 2B
0513-00
0.9630
G-X300CrNiSi952
Ni- Hard 4
0.9635
G-X300CrMo153
White Cast Iron
Hardened Cast Iron 0.9640
G-X300CrMoNi1521
Werkstoff
Germany
U.S.A.
France
Great Britain
Italy
Sweden
Spain
Japan
No.
DIN
AISI/SAE UNS
AFNOR
BS
UNI
SS
UNE
JIS
0.9645
G-X260CrMoNi2021
0.9650
G-X260Cr27
0.9655
G-X300CrMo271
0.9655
G-X300CrMo271
copyright 2010 maryland metrics
A532IIIA25%Cr
Grade 3D
A532IIIA25%Cr
Grade 3E
0466-00
Data courtesy of Kennametal
