Nokia SiteWizard 5.0 CD3.0 Product Description

SiteWizard_5_CD3.0 Nokia SiteWizard, Rel. 5 CD3.0, Product Documentation, v.1

Nokia SiteWizard Installation Instructions

DN05228246 Issue 8-4 13/03/2008

© Nokia Siemens Networks

1 (26)


The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2008. All rights reserved.

2 (26)


DN05228246 Issue 8-4 13/03/2008

Contents

Contents

DN05228246 Issue 8-4 13/03/2008

1

Introduction ............................................................................................5

2 2.1 2.1.1 2.2 2.3 2.4 2.4.1 2.4.2 2.5

Installation on Standalone PC...............................................................7 System Requirements for Installation.......................................................7 Operating System Requirements .............................................................7 Minimum Hardware requirements ............................................................7 Access Rights for Installation ...................................................................8 Installation Procedure...............................................................................8 Installation from CD-ROM ........................................................................8 Installation from NOLS ...........................................................................15 SiteWizard Installation Directory ............................................................16

3

Uninstallation Procedure.....................................................................17

4 4.1 4.1.1 4.2 4.3 4.3.1

Installation on NetAct Node Manager Server ....................................21 System Requirements for Installation.....................................................21 Operating System Requirements ...........................................................21 Minimum Hardware requirements ..........................................................21 User Access Level Control .....................................................................21 User Access Levels................................................................................21

5 5.1 5.2

Installation Troubleshooting ...............................................................24 Incorrect Privileges.................................................................................24 Windows Installer Error ..........................................................................24

6

Reference Information .........................................................................26


3 (26)


4 (26)


DN05228246 Issue 8-4 13/03/2008

Introduction

1

Introduction Nokia SiteWizard is an application package for the commissioning and maintenance of Nokia GSM/EDGE base stations. The SiteWizard Software package contains manager applications for the BTS and related transmission equipment on a BTS site. SiteWizard 5 CD3.0 contains the following managers: •

Flexi EDGE BTS Manager EP1.1

•

BTS Manager 5 CD3.0

•

BTS Hardware Configurator 5 CD3.0

•

UltraSite BTS Hub Manager C5

•

MetroHub Manager C5

•

RRI Manager C5

•

E1/T1 Manager C5

•

STM-1 Manager C5

•

FC STM-1 Manager C5

•

Bridge Manager C5

•

Hopper Manager C4.11

•

FlexiHub Manager 2.0

•

PSM Manager 4.07

•

LMU Manager 4.4

•

LMUB Manager 1.3

•

Nokia GCS R5.0

Nokia GCS (General Communication Service) is required for communication to Nokia equipment.

DN05228246 Issue 8-4 13/03/2008


5 (26)


LMU Manager, PSM Manager and LMUB Manager are provided within the Accessories folder. To install LMU, LMUB or PSM Manager, browse to the SiteWizard Accessories directory and run the desired application setup. For further information on SiteWizard 5 CD3.0 please refer to the SiteWizard 5 CD3.0 Product Description.

6 (26)


DN05228246 Issue 8-4 13/03/2008

Installation on Standalone PC

2

Installation on Standalone PC This section defines how to install SiteWizard 5 CD3.0 on a PC for local on-Site use. For instructions on how to install the SiteWizard applications on the NetAct Node Manager Server, please refer to the section Installation on the NetAct Node Manager Server.

2.1

System Requirements for Installation

2.1.1

Operating System Requirements The following Operating Systems (English Versions) are supported by SiteWizard 5 CD3.0 for local use:

2.2

DN05228246 Issue 8-4 13/03/2008

•

Microsoft Windows 2000

•

Microsoft Windows XP Professional Edition

Minimum Hardware requirements •

A Microsoft Windows compatible PC

•

Processor: Minimum recommended 500 MHz

•

Memory: 128 MB recommended or according to installed operating System (preferably the recommended amount)

•

Monitor: Minimum SVGA with 800x600 resolution (recommended 1024x768 resolution)

•

Hard disk: Recommended free Hard disk space 300 MB

•

Pointing device: Mouse, trackball, touch pad or equivalent

•

Keyboard


7 (26)


2.3

•

CD-ROM drive

•

9-pin serial port or USB port and USB-Serial converter for local connection

•

LMP cable for local connection

•

Microsoft Windows compatible printer (optional)

Access Rights for Installation For SiteWizard installation the user must be a member of the Administrator Group on the workstation. For use of the element managers it is sufficient if they are members of the Power users group. Users belonging to different domains are also able to use SiteWizard applications if their user ID is a member of power users group.

2.4

Installation Procedure

2.4.1

Installation from CD-ROM Insert the SiteWizard CD-ROM in the CD Drive of the PC. The installation program should start automatically when the CD-ROM is inserted in the CD-ROM drive. If it does not start, run Nokia SiteWizard 5 CD3.0.msi from the CD-ROM manually.

8 (26)


DN05228246 Issue 8-4 13/03/2008


1.

Welcome Screen

If not already done, exit all Windows applications and select Next.

DN05228246 Issue 8-4 13/03/2008


9 (26)


Figure 2.

License Agreement

If the terms of the License Agreement are acceptable select I accept the terms in the license agreement and then press Next otherwise select I do not accept the terms in the license agreement and then press Cancel.

10 (26)


DN05228246 Issue 8-4 13/03/2008


Figure 3.

Program Maintenance

The feature selection screen allows the user to select one of the following three tasks:

DN05228246 Issue 8-4 13/03/2008

1.

Install - If selected this feature will provide a list of applications for installation on the next screen.

2.

User Access Levels - If selected this feature enables the user Access Level Control for the BTS, LMUB and Transmission Element Managers. For further information on this feature refer to the section User Access Level Control.

3.

Remove - If selected this feature will provide a list of applications for uninstallation.


11 (26)


Figure 4.

Select applications for installation

Select the checkboxes for desired application/s. The Description and Space text on the right side and Installation path at the bottom, display the information about the highlighted (or last-clicked) application irrespective of the checkbox state i.e. whether it is selected or deselected. The Space button displays the required and available disk space on the PC to the user. SiteWizard detects the installation of GCS on the user's computer. The checkbox for GCS is by default enabled if GCS is either missing or needs an upgrade. If the user tries to deselect the GCS under these circumstances, the warning message will be displayed. However, the user can still proceed with the installation of other applications without GCS. The GCS checkbox is by default deselected if the same or newer version of GCS exists on the user's computer than provided by this

12 (26)


DN05228246 Issue 8-4 13/03/2008


SiteWizard release. The user can however select the checkbox and force the reinstallation of GCS if needed.

Figure 5.

Ready to Install

Confirm the installation by selecting Install.

DN05228246 Issue 8-4 13/03/2008


13 (26)


Figure 6.

14 (26)

Installing Applications


DN05228246 Issue 8-4 13/03/2008


Figure 7.

Installation Wizard Complete

Upon completion the user has an option to view the SiteWizard ReadMe file and Product Description. If you wish to view these, tick the check boxes and select Finish.

2.4.2

Installation from NOLS If you received the installation package as a compressed file (.zip), extract the zip file Contents into some temporary directory on your hard disk. Then run Nokia SiteWizard 5 CD3.0.msi from the directory. It is recommended not to delete the zip package in case later re-installation is required.

DN05228246 Issue 8-4 13/03/2008


15 (26)


Note The SiteWizard package is approximately 283MB.

2.5

SiteWizard Installation Directory The SiteWizard application files are installed in each application's own subfolder under C:\Program Files\Nokia. Note that PSM Manager is installed under C:\NokiaMgr parent folder. The start-up icon for each Element Manager is added into Start Æ Programs Æ Nokia Applications path. Note that GCS, Hopper Manager, FlexiHub Manager, LMU Manager, FlexiEDGE BTS Manager and LMUB Manager Icons are created under StartÆ Programs Æ Nokia path. There are no shortcuts created for STM-1 Manager and Bridge Manager as they cannot be run standalone.

16 (26)


DN05228246 Issue 8-4 13/03/2008

Uninstallation Procedure

3

Uninstallation Procedure To uninstall the individual Element Managers, select the option Remove from the Program Maintenance screen followed by selection of the applications to be removed. Uninstallation function does not uninstall GCS.

DN05228246 Issue 8-4 13/03/2008


17 (26)


Figure 8.

Remove SiteWizard Applications

To remove SiteWizard applications select the Remove option followed by Next. Note If you have saved some extra files (logs, configurations, etc.) to the Node Manager directory, those files and the directory will NOT be deleted. You need to remove them by yourself.

18 (26)


DN05228246 Issue 8-4 13/03/2008

Uninstallation Procedure

Figure 9.

Uninstallation Selection

To remove SiteWizard applications, select the applications from the list followed by Next. Note Only those applications installed on the PC will be displayed for removal.

DN05228246 Issue 8-4 13/03/2008


19 (26)


Figure 10.

Confirmation

Confirm the applications are to be removed by selecting Remove.

20 (26)


DN05228246 Issue 8-4 13/03/2008

Installation on NetAct Node Manager Server

4


4.1

System Requirements for Installation

4.1.1

Operating System Requirements The following Operating Systems (English Versions) are supported by the NetAct Node Manager Server:

4.2

•

Microsoft Windows 2000 Server Edition

•

Microsoft Windows 2003 Server Edition

Minimum Hardware requirements For details on the NetAct Node Manager Server hardware requirements refer to Node Manager Server Principles.

4.3

User Access Level Control

4.3.1

User Access Levels There are two access levels possible for various features and functionalities in the BTS, LMUB and ITN Transmission Element Managers when used remotely from the NetAct Node Manager Server: •

DN05228246 Issue 8-4 13/03/2008

Read Only (Basic user)


21 (26)


•

Full Access (Administrator)

With Read Only access level the user will only be able to view the properties of the node. The user will not be allowed to change the node properties. This is the restricted mode provided by the access control. With Full access level the user will be able to read and modify the node settings. By adding users to a user group named Nokia BTS_Admins users can have full access rights assigned. Users not being part of this user group will have read only access rights. Note The user group "Nokia BTS_Admins" is created when User Access Levels checkbox is ticked and the Next button is pressed in the Program Maintenance screen.

Figure 11.

22 (26)

Enabling of User Access Level Control feature


DN05228246 Issue 8-4 13/03/2008


If the user checks the tick-box User Access Levels at the time of SiteWizard installation then the user access level functionality is enabled and by administering the user group Nokia BTS_Admins full access or read only access rights can be assigned to individual users. If User Access Levels is not selected, the user access level functionality is disabled (by default, all users have read/write access). Note Access levels are enabled only for Remote Connection. In local connection this feature is disabled and the user has all the normal rights even if the registry key is present.

Note With Full Access there are certain restrictions to ensure the remote connection is not lost due to error. These restrictions include running of the Commissioning Wizard, Reset to Factory Settings and Restore Back-up Settings. The table below describes what actions are required for the User Access Level feature.

Table 1.

User Access Level Control

I wish all users to have restricted access (read only)

I wish some users to have restricted access (read only)

I wish all users to have full access (read/write)

1.

2.

Check the User Access Level tickbox at the time of SiteWizard Installation or Upgrade

1.

3.

Add the users who should have full access to the Nokia BTS_Admins Group

Check the User Access Level tickbox at the time of SiteWizard Installation or Upgrade

Do not check the User Access Levels tick-box at the time of SiteWizard Installation or Upgrade

For additional information about enabling, disabling or administering User Access level functionality refer to Nokia MetroHub Transmission Node Rel. C3 Managing Nokia MetroHub Software document.

DN05228246 Issue 8-4 13/03/2008


23 (26)


5

Installation Troubleshooting

5.1

Incorrect Privileges If the Installer of SiteWizard does not have Admin rights to the workstation the following error message will be displayed.

Figure 12.

5.2

Incorrect Privileges

Windows Installer Error SiteWizard 5 CD3.0 requires Windows Installer version 3.1 installed on the computer as prerequisite. Below is a link which may help in resolving common problems faced due to Windows Installer engine. http://support.installshield.com/kb/view.asp?pcode=ALL&articleid=Q1 07137

24 (26)


DN05228246 Issue 8-4 13/03/2008

Installation Troubleshooting

DN05228246 Issue 8-4 13/03/2008


25 (26)


6

Reference Information For more information on Windows Installer or latest Windows Installer downloads, refer to Microsoft support web pages. •

For further information on SiteWizard 5 CD3.0 DN04130437 SiteWizard 5 CD3.0 Product Description

•

For general information on the NetAct Node Manager Server DN03410658 Node Manager Server Principles

•

For information on administrative tasks in the Node Manager Server DN03535662 Administering Node Manager Server

•

For information on how to take backups in the Node Manager Server DN00301944 Node Manager Server backup in Taking Backups of the NetAct File Systems and Databases

•

For troubleshooting the Node Manager Server DN0519251 Troubleshooting Node Manager Server Problems

•

For information on the NetAct system security DN0567527 Managing NetAct System Security

•

For information on using General Communication Service (GCS) DN011794 GCS User Manual

•

For additional information about administering User Access level functionality DN0420769 Managing Nokia MetroHub Software

26 (26)


DN05228246 Issue 8-4 13/03/2008

Nokia SiteWizard 5.0 CD3.0 Product Description

Recommend Documents