Perhitungan Piping system Kapal Ikan FV HIDAYATFull description
Berisi panduan cara melakukan hidrostatis tes untuk sistem perpipaan
Full description
MS for Underground Piping
Piping Tie in Procedure Rev A
piping notesFull description
Book on PipingFull description
piping
Piping
Book on Piping
Descripción completa
Book on PipingDescripción completa
Book on PipingFull description
Descripción: Piping
INTRODUCTION Day One Piping Systems Friction Losses Flow Rate limitation Ashrae & Carrier Guide Line Acceptable Practices Pipe Sizing Head Losses Calculation Case Practice
Day 2
Pumps Performance Curves Power consumption & Efficiency Curve Pump Laws Pumps & System Curve
NPSHR & NPSHA Pump Selection Pumps Arrangements & their performance Curve Case Studies
WATER PIPING SYSTEM Open System In this system, the water flows thru heat exchanger and then exposed to atmosphere. such as in Cooling tower and air washer.
Closed system In this system, the water flow is not exposed to the atmosphere at any point. But some times contains an expansion tank that is open to the atmosphere but water area exposed is insignificant. Such as Chilled water system
Closed Water Piping System Parallel Piping System Reverse return piping Reverse return header with direct return risers Direct return piping
Compound Piping system (Primary & Secondary System)
Reverse Return Piping
Reverse Return Headers with Direct Return Risers
Direct Return Water Piping
Primary & Secondary Piping
FRICTION LOSSES When water flows in a pipe, friction is produced by the rubbing of water particles against each other and against the wall of the pipe. This friction produced by the flowing water causes a loss in pressure, which is called Friction Loss. The Friction losses depends upon: Water velocity Interior surface roughness Pipe length Pipe diameter
Flow Rate Limitation Services Erosion Noise Installation Cost Operating Cost All above limit Maximum and minimum velocities in piping system.
Recommended Water Velocities Based on Services Pump Discharge
8-12 FPS
Pump Suction
4-7 FPS
Header
4-15 FPS
Riser
3-10 FPS
Drain Line
4-7 FPS
General Service
5-10 FPS
City Water
3-7 FPS
Erosion Erosion in water piping system is the impingement on inside surface of pipe of rapidly moving water containing air bubbles, sand and other solid matter. Due to this impingement, pipes gets eroded over a period of time if Recommended velocity not maintained in piping systems.
MAXIMUM WATER VELOCITY TO MINIMIZE EROSION Normal Operation
Velocity Range
1500 Hrs/Year
15 FPS
2000 “
14 FPS
3000 “
13 FPS
4000 “
12 FPS
6000 “
10 FPS
8000 “
8 FPS
Noise Generation Velocity-dependent noise in piping systems results from any or all of four sources: Turbulence Cavitation Release of entrained air Water hammer
In investigations of flow-related Noise, Marseille, Ball and Webster and Rogers reported that velocities on the order of 10 to 17 fps lie within the range of allowable noise levels for residential and commercial buildings.
Ashrae Recommendations For Hydronic System Friction Loss Rate should be taken as 1 to
4 Feet/100 feet of Pipe Eq.Length. A Value of 2.5 Feet/100 Feet is the mean to which most systems are designed. For 2 Inch and below pipes, Velocity limit is 4 FPS. For above pipes, FLR limit is 4 Feet/100 Feet. And As per Carrier Guide Line FLR is 8-10 feet /100 feet and velocity limit 10 FPS.
PIPE SIZING CRITERIA Water Flow Based on Cooling load on respective AHU /FCU/BCU Can be calculated as: Tonnage X 24 Flow In GPM= --------------------------------Temperature difference
Friction Loss Rate / Velocity Limitation specified by consultant or ASHRAE.
Pipe Sizing Method Step -1 Make a layout sketch showing individual AHU,FCU and BCU on Master layout plan.
Step - 2 Mark selected /design flow on individual AHU, FCU and BCU.
Step - 3 Review layout sketch w.r.t. space available , other services,economy and consultant concurrence. Conclude layout.
Pipe Sizing Method…….. Step -4 Starting from most remote terminal working towards the pump, Mark the Cumulative flow in mains and branch circuits.
Step -6 Select pipe size for required Flow and as per selected Friction Loss Rate from Friction chart for respective application. Re-check Chart water velocity with recommended velocity. If within limit.Selection is ok. Repeat
for other flow requirements.
Friction Loss Rate Vs Flow Charts -
Sch. 40 pipes
Head Loss & Calculation It is the total loss of pressure energy due to friction/resistance offered by Pipes & Fittings in the piping system The Head Loss is equal to the Total Frictional Losses in highest resistant circuit of piping system. To Calculate Head Loss, Calculate the Total Frictional Losses of pipes of fittings of equipments
Valve & Fitting Losses Valves & Fitting cause pressure losses greater than those caused by the pipe alone. Fitting Losses are frequently expressed in Equivalent length of pipe, It can be expressed as per following equation h = K x V2/2g h- Head/Pressure loss in Feet K - Geometry & Size dependent loss coefficient V - Average velocity of water g - Gravitational force as 32.20
K Factors-Screwed Fittings
K Factors-Flanged Fittings
Fitting Losses in Equivalent Length of Pipe
Valves Losses in Eq. Length of Pipes
System Friction Losses Relation between Flow & Head Losses for a system: 1.85 -1.9 H2/H1 = (Q2/Q1) Q1& Q2 = Flows H1 & H2=Head Losses
Water Piping Diversity
When the air conditioning load is determined for each exposure of a building, it is assumed that the exposure is at peak load. Since the sun load is at a maximum on one exposure at a time, not all of the units on all the exposures require maximum water flow at the same time to handle the cooling load. Units on the same exposure normally require maximum flow at the same time; units on the adjoining or opposite exposures do not. Therefore, if the individual units are automatically controlled to vary the water quantity, the system water quantity actually required during normal operation is less than the total water quantity required for the peak design conditions for all the exposures.
Diversity Application The principle of diversity allows the
engineer to evaluate and calculate the reduced water quantity. For applying diversity two conditions must be satisfied: The
water flow to the units must he automatically controlled to compensate for varying loads. Diversity may only be applied to piping that supplies units on more than one exposure.
Diversity Application
•Calculate Accumulated Flow in exposure. •Find Out Ratio of Accumulated flow to Total Pump Flow. •Apply this ratio to diversity Charts and obtain diversity factor for the particular section.
Diversity Application
A Sample Project
A schematic chilled water piping layout is enclosed for a G+4 Building. Please size the pipes for individual branch and headers. Calculate the total friction losses. Select the Pumps: Option 1- With single pumps operation Option 2- With two pumps in operation