PLANO ELECTRICO BULLDOZER D9N CATERPILLAFull description
Full description
plano eléctrico motoniveladora 160K caterpillar
caterpillar excavadora 330lDescripción completa
Descripción: 777G
manual pala hidraulicaFull description
Manual Control Pala Hidraulica Pc5500 KomatsuFull description
INTERACTIVE SCHEMATIC Bookmarks
*This document is best viewed at a screen resolution of 1024 X 768. To set your screen resolution do the following: RIGHT CLICK on the DESKTOP. Select PROPERTIES. CLICK the SETTINGS TAB . MOVE THE SLIDER under SCREEN RESOLUTION until it shows 1024 X 768. CLICK OK to apply the resolution.
The Bookmarks panel will allow you to quickly navigate to points of interest.
EC-C2 EC-C3
*Due to different monitor sizes and PDF reader preferences there may be some variance in linked schematic locations
Click here to save a copy of this interactive schematic to your desktop
E-C60 E-C61
VIEW ALL CALLOUTS EC-C1
Click on any text that is BLUE BLUE and and underlined. These are hyperlinks that can be used to navigate the schematic and machine views.
When only one callout is showing on a machine view, clicking on this button will make all of the callouts visible. This button is located in the top right corner of every machine view page.
ELECTRICAL SYMBOLS
HOTKEYS (Keyboard Shortcuts)
BASIC HYDRAULIC COMPONENTSYMBOLS
T
FUNCTION
KEYS
Zoom In
“CTRL” / “+”
Zoom Out
“CTRL” / “-”
Fit to Page
“CTRL” / “0” (zero)
Hand Tool
“SPACEBAR” (hold down)
Find
“CTRL” / “F”
Search
“CTRL” / “SHIFT” / “F”
Pressure Switch
Temperature Switch
Level Switch
Flow Switch
Circuit Breaker
Click here to view the Schematic Symbols and Definitions page
Pump or Motor
Variability
Fluid Conditioner
Spring (Adjustable)
SCHEMATIC SYMBOLS AND DEFINITIONS VALVES
INTERNAL PASSAGEWAYS
ENVELOPES
Two Position
One Position
Three Position
PORTS
Two-way
Three-Way
FLOW IN ONE DIRECTION
FLOW ALLOWED IN EITHER DIRECTION
Infinite Positioning
Two Position
PARALLEL FLOW
PUMPS CROSS FLOW
Unidirectional
Three Position
BASIC HYDRAULIC COMPONENT SYMBOLS
FIXED DISPLACEMENT DISPLACEMENT
Pump or Motor
Variability
Fluid Conditioner
Spring (Adjustable)
Spring
Pressure Compensation
Control Valves
Line Restriction (Variable)
Restriction
Line Restriction (Fixed)
Line Restriction Variable and Pressure Compensated
2-Section Pump
Attachment
Pump: Variable and Pressure Compensated
Bidirectional
VARIABLE DISPLACEMENT NON- COMPENSATED
CYLINDERS
Four-Way
Unidirectional
Bidirectional
CONTROL A B
A B
P T
P T
Single Acting
FIXED DISPLACEMENT DISPLACEMENT
Shifted Position
Normal Position
MOTORS
Double Acting
Infinite Position
CHECK
ACCUMULATORS Basic Symbol
Spring Loaded
Shuttle
Unidirectional
Bidirectional
VARIABLE DISPLACEMENT NON- COMPENSATED
Pilot Controlled
Spring Loaded Gas Charged
Unidirectional
Bidirectional MAIN AUX.
PILOT CONTROL
ROTATING SHAFTS
RELEASED PRESSURE
Unidirectional
External Return
Internal Return
Bidirectional
REMOTE SUPPLY PRESSURE
Simplified
Complete
Internal Supply Pressure
Hydraulic Pneumatic Energy Triangles
COMBINATION CONTROLS LINES
Solenoid
Solenoid or Manual
Solenoid and Pilot
Solenoid and Pilot or Manual
Servo
Thermal
Detent
Crossing
MANUAL CONTROL
Push-pull Lever
Manual Shutoff
General Manual
MEASUREMENT
Joining
Pressure
Temperature
Flow
FLUID STORAGE RESERVOIRS
Push Button
Pedal
Spring
Vent Vented ed
Pres Pressu suri rize zed d
Retu Return rn Abov Above e Flui Fluid d Leve Levell
Retu Return rn Belo Below w Flui Fluid d Leve Levell
ELECTRICAL SYMBOLS
HYDRAULIC SYMBOLS - ELECTRICAL
M
G
T
Transducer (Fluid)
Transducer (Gas / Air)
Generator
Electric Motor
Pressure Switch
Pressure Switch (Adjustable)
Temperature Switch
Electrical Wire
Pressure Switch
Temperature Switch
BASIC ELECTRICAL COMPONENT SYMBOLS Fuse: A component in an electrical circuit that will open the circuit if too much current flows through it.
Level Switch
Flow Switch
Circuit Breaker
HARNESS AND WIRE SYMBOLS Wire, Cable, or Harness Assembly Identification: Includes Harness Identification Letters and Harness Connector Serialization Codes (see sample).
Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The circle indicates that the component has screw terminals and a wire can be disconnected from it. Switch (Normally Closed): A switch that will open at a specified specified point (temp, press, etc.). No circle indicates that the wire cannot be disconnected from the component.
1
Part Number: for Number: for Connector Plug
2
Ground (Wired): This indicates that the component is connected to a grounded wire. The grounded wire is fastened to the machine. Plug
Ground (Case): This indicates that the component component does not have a wire connected to ground. It is grounded by being fastened to the machine. Reed Switch: A Switch: A switch whose contacts are controlled controlled by a magnet. A magnet closes the contacts of
L-C12 3E-5179
AG-C4 111-7898
Receptacle Pin or Socket Number
Harness Identification Letter(s): (A, B, C, AA, AB, AC, ...) Harness Connector Serialization Code: The Code: The "C" stands for "Connector" and the number indicates which connector connector in the
UENR5436-02 January 2017
6015B Hydraulic Mining Shovel Electrical System LWN1-UP WSN1-UP
The connectors shown in this chart are for harness to harness connectors. Connectors that join a harness to a component are generally located at or near the component. See the Component Location Chart.