Proceduri VAG COM

Proceduri VAG–COM - http://vwforum.promotor.ro

PROCEDURI VAG-COM

1


CUPRINS:

Activare Coming Home & Leaving Home ........................................................................... 3 Activare DRL(s) pe proiectoare la 50% din intensitate ........................................................ 4 Activarea funcţiei "cornering" pe proiectoare ....................................................................... 5 Activare Tempomat pe un nou ECU (DBW): ....................................................................... 5 Activare funcţie Staging (testare ace indicatoare la pornire) ................................................ 5 Activare Auto Rain Closing Windows and Sunroof ............................................................. 6 Activare roll up/down ............................................................................................................ 8 Adaptare chei ....................................................................................................................... 12 Afisarea vitezei pe ecranul Radio CD. ................................................................................ 19 Anularea diagnosticarii "eroare bec ars" pentru semnalizare ............................................. 20 Deschiderea pistoanelor pentru inlocuirea placutelor de frana pe spate ............................. 20 Descuiarea automata a masinii dupa scoaterea cheii din contact........................................ 20 Dezactivare avertizor sonor centură de siguranţă ............................................................... 21 Închiderea pistoanelor dupa inlocuirea placutelor de frana pe spate .................................. 22 Incuierea automata a uşilor dupa viteza de 15km/h ............................................................ 22 Închidere automata a geamurilor tinand apasat butonul doar 2 secunde ............................ 22 Lumini de poziţie faţă stil US (cu lămpile de semnalizare) ................................................ 24 Lumini de poziţie spate stil DONUTS (cu centrul stins): ................................................... 24 Modificare mile in kilometri (USA/Canada/Uk/Europa/Japan) ......................................... 24 Modificarea sunetului alarmei ............................................................................................. 25 Modificarea limbii pe afisajul display-ului ......................................................................... 26 Regenerarea filtrului de particule (DPF). ............................................................................ 26 Reglarea sensibilităţii direcţiei în funcţie de viteză ............................................................ 27 Testul catalizatorului ........................................................................................................... 28

2


Activare Coming Home & Leaving Home NOTA: NU este necesar ca masina voastra sa aiba faruri automate sau senzor de lumina pt a activa aceste functii! CODE [Select] [09 - Cent. Elect.] [07 - Coding] [Long Coding Helper] Byte 0: - bifati Bit 5 (Assistance Driving Light - Leaving Home active) - bifati Bit 7 (Coming-Home active) [Transfer Coding!] [Do It!] Modificare timpilor pt Coming Home & Leaving Home CODE [Select] [09 - Cent. Elect.] [10 - Adaptation] Channel 01: numarul de secunde care doriti ca coming home sa fie activ - de la 0 pana 120 Channel 02: numarul de secunde care doriti ca leaving home sa fie activ - de la 0 pana 120 [Test] [Save] [Done, Go Back] Asta e tot. Puteti incepe testarea noilor functii: - introduceti cheie in penultima pozitie a contactului (cea in care se aprind toti martori) - dupa cateva secunde, scoate cheia din respectiv pozitie - scoate de tot cheia din contact Pozitiile, faza scurta cat si stopurile ar trebui sa ramana aprinse. Iesiti din masina, inchideti usa soferului si inchideti masina din telecomanda. Luminile fata si stopurile spate ar trebuie sa se inchida dupa ce timpul specificat in Channel 01 a trecut. Dupa ce s-au inchis luminiile, deblocati masina din telecomanda si veti observa ca pozitia, faza scurta cati si stopurile spate vor porni. Ele vor ramane pornite pana cand unul din urmatoarele trei lucruri se va intampla: 1) Ati deschis usa soferului 3


2) Veti bloca masina din nou 3) Timpul specificat in Channel 02 a trecut. NOTA: Singura conditie ca functia Coming Home sa mearga, este sa lasati comutatorul de lumini pe pozitia faza scurta. Functia Leaving Home este independenta de aceasta conditie. Se poate activa pe octavia 2 chestia aia cu stinsul proiectoarelor cand dai faza lunga si Coming Home & Leaving Home scuze ca am postat in aria de passat dar nu am vazut(gasit) la octavia si mi-a spus un prieten la care am vazut astea activate ca aici a gasit despre aceste functii La passat asa este, asa ar trebui sa fie si la O2: [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 17: bifati Bit 5 (Front Fog lights deactivated with High Beam) [Transfer Coding!] [Do It!]

Activare DRL(s) pe proiectoare la 50% din intensitate CODE [Select] [09 - Central Electric] [07 - Coding] [Long Coding Helper] Byte 00: - bifati Bit 4 (Daytime Running Lights (North America)) Byte 17: - bifati Bit 4 (Daylight Running Light via Front Fog Lights) Byte 20:- in casuta DEC modificati valoare (in procente) in 50 [Transfer Coding!] [Do It!] Respectiva valoare inscrisa in casuta DEC poate fii modificata dupa bunul plac Nu merge decat pe proiectoare sau pe faza scurta . Asta din ce am vazut eu asa cu coada ochiului in VAG-COM . ! Daca frana de deget este apasata proiectoarele (acum DRL) se sting! Dupa ce decuplez frana de deget se aprind! Daytime Running Lamp sau Daylight Running Lamp adica lumini de zi 4


DRL Scandinavia = pozitii + proiectoare fata aprinse NON-STOP(stopurile spate nu sunt aprinse) DRL North America = proiectoarele fata sunt aprinse din momentul in care ai pornit motorul si ai dezactivat frana de mana, pana la activarea ei sau oprire motorului

Activarea funcţiei "cornering" pe proiectoare NOTA: Aceasta functie merge activata doar la masiniile produse DUPA iulie 2007! CODE [Select] [09 - Cent. Elect.] [10 - Coding] [Long Coding Helper] Byte 23: - bifati Bit2 (Internal Turn Light Control Algorithm active) - selectia la Bit-ul 3-4: 08 Turn Lights via Fog Lights [Transfer Coding!] [Do It!]

Activare Tempomat pe un nou ECU (DBW): Factory fresh ECU's often come with cruise control de-activated. [Select] [01 - Engine] [Login - 11] Enter 11463 to activate cruise control [Do It!] Installing a new ECU:

Activare funcţie Staging (testare ace indicatoare la pornire) (This is Not supported on all instrument clusters). Address 17 -- Instruments Adaptation 10 5


Select "Staging" from the drop down list Select "Active" from the drop down list Save the changes Done!

Activare Auto Rain Closing Windows and Sunroof An undocumented feature on the Golf MKV is automatic rain closing windows. The only requirement is having a RegenLichtSens (RainLightSensor) Operation of the system Rain closing activates only when the car has been locked. The windows and sunroof if fitted will close automatically after 24 hours. To activate the feature there are two steps, one is to enable the feature and one is to enable the menu if there is a full height MFD to give the option to enable or disable. If there is no full height MFD the system will still operate correctly but to enable or disable you will need to use Vagcom/VCDS. If the car is fitted with an alarm and the interior sensors these will need to be disabled by pressing the button on the B pillar before locking the car as operation of the sunroof and windows may activate the alarm. The wiper stalk may need to be in the automatic/intermittent position to operate. Step 1 – Enable Auto Rain Closing Open the Central Electronics Controller (09) and click on the “Coding” option. Click the drop down box and choose the RegenLichtSens (RainLightSensor)

6


Note the software coding (00)208933) (most cars have different codings) Convert to Hex (0)3 30 25 Add 4 to the left hand value Hex (0)7 30 25 Convert to Decimal (00)471077 and replace the old coding. If you’re unclear on the conversion steps see the Decimal to Hex and Hex to Decimal conversion guide. Step 2 – Enable Menu to Enable/Disable (optional) Open the Comfort System Controller (46)

7


In long coding change Byte 09 to Hex 02

Example 13 90 06 88 51 03 48 3F 2D 04 05 8F B0 08 0A 04 88 9C 00 to 13 90 06 88 51 03 48 3F 2D 02 05 8F B0 08 0A 04 88 9C 00 The menu will now give you the option to turn on or off the Rain Closing Feature. Testing To test wind down the windows and open sunroof if fitted, lock the car. Wait around 2 minutes and pour some water on the rain sensor (mounted on the glass behind the rear vision mirror) and after a short delay the windows and sunroof will close. Issues There are really no issues with enabling this feature. There have been a few reports of people getting a fault appearing in their Central Electronics Controller (09) from time to time “02071 – Local Databus- 004 – No Signal/Communication – Intermittent” but the system operates correctly and for some people depending on the revision of the RegenLichtSens where it just doesn’t operate. La mine: 46 Byte 9 110 Schimbat: 010 OLD 4091020051034E763006941570084F0E707C01 New 4091020051034E763002941570084F0E707C01

Activare roll up/down [Select] [46 - Central Conv.] [07 - Coding] 8


[Long Coding Helper] Byte 6: - bifat Bit 6 (Comfort function autom. closing) [Transfer Coding!] [Do It!] Procedura de mai sus nu a mers... am bifat ce a zis pronet dar nu a functionat. am salvat codul original asa ca oricand pot face backup, deci imi permit sa mai si gresesc. cine imi poate spune, in lista de mai jos (sursa openobd.org/passat 3c) ce biti ar trebui sa fie bifati si unde pt roll up/down si sunroof close din telecomanda? Select 46 (Comfort System) Long Coding -> Function 07 Byte 00 Bit 0 Selective Central Locking Byte 00 Bit 1 Central Locking w/o Safe-Function Byte 00 Bit 2 Central Locking w/o sensible Byte 00 Bit 3 Auto-Unlock (unlocking after removing key from ignition) Byte 00 Bit 4 Auto-Lock (autom. locking above 10 mph) ... unknown... Byte 06 Bit 0 Comfort function inactive Byte 06 Bit 1 Comfort function power windows/sunroof via door lock drivers door inactive Byte 06 Bit 2 Comfort function power windows/sunroof via door lock passengers door inactive Byte 06 Bit 3 Comfort function power windows/sunroof via door lock rear lid inactive Byte 06 Bit 4 Comfort function power windows/sunroof via power window switch in drivers door inactive Byte 06 Bit 5 Comfort function power windows/sunroof via remote control inactive Byte 06 Bit 6 Comfort function autom. closing Byte 06 Bit 7 Power windows/sunroof disabled after door opening Byte 07 Bit 0 Comfort opening power windows via door lock active Byte 07 Bit 1 Comfort opening power windows via power window switch active Byte 07 Bit 2 Comfort opening power windows via remote control active Byte 07 Bit 3 Comfort closing power windows via door lock active Byte 07 Bit 4 Comfort closing power windows via power window switch active Byte 07 Bit 5 Comfort closing power windows via remote control active Byte 07 Bit 6 Comfort function after authorized access only in a limited time Byte 07 Bit 7 not relevant/unused Byte 08 Bit 0 Comfort opening sunroof via door lock active Byte 08 Bit 1 Comfort opening sunroof via power window switch active Byte 08 Bit 2 Comfort opening sunroof via remote control active Byte 08 Bit 3 Comfort closing sunroof via door lock active Byte 08 Bit 4 Comfort closing sunroof via power window switch active 9


Byte 08 Bit 5 Comfort closing sunroof via remote control active Byte 08 Bit 6 not relevant/unused Byte 08 Bit 7 not relevant/unused ... unknown... Byte 10 Bit 0 Unlocking Confirmation (Blink) via Door Locks Byte 10 Bit 1 Unlocking Confirmation (Horn) via Door Locks Byte 10 Bit 2 Unlocking Confirmation (Blink) via Remote Control Byte 10 Bit 3 Unlocking Confirmation (Horn) via Remote Control Byte 10 Bit 4 Unlocking Confirmation (Blink) via Kessy Byte 10 Bit 5 Unlocking Confirmation (Horn) via Kessy Byte 10 Bit 6 not relevant/unused Byte 10 Bit 7 Adaptation of Horn Confirmation locked Byte 11 Bit 0 Locking Confirmation (Blink) via Door Locks Byte 11 Bit 1 Locking Confirmation (Horn) via Door Locks Byte 11 Bit 2 Locking Confirmation (Blink) via Remote Control Byte 11 Bit 3 Locking Confirmation (Horn) via Remote Control Byte 11 Bit 4 Locking Confirmation (Blink) via Kessy Byte 11 Bit 5 Locking Confirmation (Horn) via Kessy Byte 11 Bit 6 not relevant/unused Byte 11 Bit 7 not relevant/unused ... unknown... Byte 13 Bit 0 Remote control inactive Byte 13 Bit 1 Remote control with "Terminal 15 ON" inactive Byte 13 Bit 2 Remote control range limitation active Byte 13 Bit 3 Manual remote control lerning/unlearning active Byte 13 Bit 4 not relevant/unused Byte 13 Bit 5 not relevant/unused Byte 13 Bit 6 Activation Blink Signal (Anti-Theft-Warning System) Byte 13 Bit 7 Activation Horn Signal (Anti-Theft-Warning System) Byte 14 Bit 0 Doors (0 = 2-doors / 1 = 4-doors) Byte 14 Bit 1 Power windows front installed Byte 14 Bit 2 Power windows rear installed Byte 14 Bit 3 Central locking installed Byte 14 Bit 4 Model (0 = Left Hand Drive/ 1 = Right Hand Drive) Byte 14 Bit 5 not relevant/unused Byte 14 Bit 6 Synchronous mirror adjustment Byte 14 Bit 7 Mirror lowering with reverse gear (only with Memory Seats) Byte 15 Bit 0 Anti-theft system deactivated Byte 15 Bit 1 Anti-theft system disarming only via remote control or immobilizer Byte 15 Bit 2 not relevant/unused Byte 15 Bit 3 Anti-theft alarm delay (15 s) inactive (Thatcham) Byte 15 Bit 4 not relevant/unused 10


Byte 15 Bit 5 Anti-theft system passive arming Byte 15 Bit 6 Inclination Sensor installed Byte 15 Bit 7 Interior Monitoring installed Byte 16 Bit 0 not relevant/unused Byte 16 Bit 1 not relevant/unused Byte 16 Bit 2 not relevant/unused Byte 16 Bit 3 not relevant/unused Byte 16 Bit 4 Siren installed Byte 16 Bit 5 Siren Tone Type (0 = frequency modulated / 1 = intermittent) Byte 16 Bit 6 Siren Alarm Type (0 = 10 "tamper" alarms / 1 = 1 "tamper" alarm) Byte 16 Bit 7 not relevant/unused R: ai incercat? : Byte 08 Bit 0 Comfort opening sunroof via door lock active Byte 08 Bit 1 Comfort opening sunroof via power window switch active Byte 08 Bit 2 Comfort opening sunroof via remote control active Byte 08 Bit 3 Comfort closing sunroof via door lock active Byte 08 Bit 4 Comfort closing sunroof via power window switch active Byte 08 Bit 5 Comfort closing sunroof via remote control active iar acestia nebifati: Byte 06 Bit 0 Comfort function inactive Byte 06 Bit 1 Comfort function power windows/sunroof via door lock drivers door inactive Byte 06 Bit 2 Comfort function power windows/sunroof via door lock passengers door inactive Byte 06 Bit 3 Comfort function power windows/sunroof via door lock rear lid inactive Byte 06 Bit 4 Comfort function power windows/sunroof via power window switch in drivers door inactive Byte 06 Bit 5 Comfort function power windows/sunroof via remote control inactive nebifat Bifat

Byte 06 Bit 0 Comfort function inactive Byte 06 Bit 6 Comfort function autom. Closing

Deci 208933(dec) = 033025 (hex) adica: According the ross-tech wiki page this should be: 03 = Highway Lights + Rain Lights 30 = 48 % light sensor correction 25 = 37 % rain sensor correction 11


Deci pentru a functiona rain closing se adauga 4 la primul byte in hexa si iese 073025 (hex) care transformat in dec este: 471077. deci trebuie sa-l recodezi la soft coding cu 00471077. Bafta.

Adaptare chei Select] [17 - Instruments] [Login - 11] [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do It!] [Adaptation - 10] Enter 21 in "Channel Number" [Read] The "Stored Value" is the number of keys currently matched. Enter "new value" of 0 [Save] This clears out the old key-matchings. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys [Save] [Done, Go Back] [Close Controller, Go Back - 06] Switch ignition off and remove key Insert next key to ignition and switch ignition on again. The warning light for the Immobilizer will light up for ~2 seconds, then go out. Switch ignition off and remove key Repeat step 16 with each key until all keys have been matched IMMO II Determining IMMO-ID [Select] [25 - Immobilizer] 12


Look at the "Component" field. The 14-digit string in the Immo-ID. [Close Controller, Go Back – 06 Key Matching Prerequisites: You can match up to 8 keys. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. Battery voltage at least 12.0 V. [Select] [25 - Immobilizer] [Meas. Blocks - 08] Select Block 001. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner. [Done, Go Back] [Login - 11] There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!] [Adaptation - 10] Enter 01 in "Channel Number" (if not available use Channel 21). [Read] The "Stored Value" is the number of keys currently matched. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. The old keys are automatically beeing cleared. [Save] [Done, Go Back] [Close Controller, Go Back - 06] 13


Repeat the following steps until all keys have been matched: Switch ignition off and remove key. Insert next key to ignition and switch ignition on again. The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key. Note: The above steps after saving the adaptation, should not exceed 30/60 seconds! IMMO III - Immobilizer III Key Matching (Cluster) Determining IMMO-ID & VIN [Select] [17 - Instruments] Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID. [Close Controller, Go Back - 06] ---OR--[Select] [17 - Instruments] [Meas. Blocks - 08] Select Block 081. [Go!] The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.. [Done, Go Back] [Close Controller, Go Back - 06] Key Matching Prerequisites: All keys are either new or were adapted to this car (IMMO-ID) before. You can match up to 8 keys. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. Battery voltage at least 12.5 V. [Select] [17 - Instruments] [Meas. Blocks - 08] Select Block 022. 14


[Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner. Select Block 024. [Go!] Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes). If the lock times are NOT 0: Do NOT switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3. [Done, Go Back] [Login - 11] There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!] IMMO III - Immobilizer III Key Matching (Separate) Determining IMMO-ID & VIN [Select] [25 - Immobilizer] Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID. [Close Controller, Go Back - 06] ---OR--[Select] [25 - Immobilizer] [Meas. Blocks - 08] Select Block 081. 15


[Go!] The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.. [Done, Go Back] [Close Controller, Go Back - 06] Key Matching Prerequisites: All keys are either new or were adapted to this car (IMMO-ID) before. You can match up to 8 keys. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. Battery voltage at least 12.0 V. [Select] [25 - Immobilizer] [Meas. Blocks - 08] Select Block 001. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner. Select Block 003. [Go!] Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes). If the lock times are NOT 0: Do NOT switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3. [Done, Go Back] [Login - 11] There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] 16


VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!] [Adaptation - 10] Enter 01 in "Channel Number". [Read] The "Stored Value" is the number of keys currently matched. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. The old keys are automatically beeing cleared. [Save] [Done, Go Back] [Close Controller, Go Back - 06] Repeat the following steps until all keys have been matched: Switch ignition off and remove key. Insert next key to ignition and switch ignition on again. The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key. Note: The above steps after saving the adaptation, should not exceed 60 seconds! IMMO III - Immobilizer III Key Matching (Kessy) Determining IMMO-ID & VIN [Select] [05 - Acc/Start Auth.] [Meas. Blocks - 08] Select Block 081. [Go!] The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.. [Done, Go Back] [Close Controller, Go Back - 06] Key Matching Prerequisites: Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger. You can match up to 8 keys. All keys are either new or were adapted to this car (IMMO-ID) before. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. 17


If all Keys are new OR the first inserted Key is new, the Ignition will NOT switch ON with this key. Put the first Key into the ignition Lock, but do NOT switch ON the ignition. Press and Hold the Brake Pedal for 20 Seconds to wake up the Diagnostic Databus. [Select] [05 - Acc/Start Auth.] [Meas. Blocks - 08] Select Block 022. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner. Select Block 023. [Go!] Make sure the shown lock times in field 1, 2, 3 and 4 are 0 (each field represents a time in minutes). If the lock times are NOT 0: Do NOT switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-4. [Done, Go Back] [Sec. Access - 16] There are 2 possibilities how to enter a PIN, choose the one that applies for you 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!] [Adaptation - 10] Enter 21 in "Channel Number". [Read] The "Stored Value" is the number of keys currently matched. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. 18


The old keys are automatically being cleared. [Save] [Done, Go Back] [Close Controller, Go Back - 06] Switch Ignition OFF and remove Key, Steering Lock should engage. Insert first Key again and switch Ignition ON. The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key. Repeat the following steps until all keys have been matched: Switch Ignition OFF and remove Key, Steering Lock should engage. Insert next Key to Ignition and switch Ignition ON again. The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key. Note: The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!

Afisarea vitezei pe ecranul Radio CD. Daca setezi sa se vada viteza, nu se mai vede titlul melodiei sau postul de radio. CODE [Select] [56 - Radio] [10 - Adaptation] Channel 02: 0 = dezactivare / 1 = activare (afisarea vitezei in km/h pe display-ul radioului) [Test] [Save] [Done, Go Back] Dupa aceasta operatie se apasa butonul meniu (de la radio-CD) si in acelasi timp se apasa pe butonul de pornire (power). Dar pe ecranul climatronicului ? Se tine apasat pe ECON si in acelasi timp pe Recirculare sau celalat de langa recirculare, apoi in afisajul din stanga al cliamtronicului apar modulele ( 01, 02, 03.....)se invarte de roata climatorinic stanga pana se se ajunge la 19 iar in partea dreapta iti va afisa viteza in km... nu stiu ce inseamna celelate module doar 19 stiu ca e viteza.... 19


Anularea diagnosticarii "eroare bec ars" pentru semnalizare

(ATENŢIE! POATE AFECTA SIGURANŢA CIRCULAŢIEI!!!) CODE [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 18: - debifezi Bit 5 (Cold Diagnosis Turn Signals active) - debifezi Bit 7 (Cold Diagnosis Side Turn Signals active) [Transfer Coding!] [Do It!]

Deschiderea pistoanelor pentru inlocuirea placutelor de frana pe spate CODE [Select] [53 - Parking Brake] [04 - Basig Settings] Grup: 006 [Start!] Activating basic settings [CON/DEC/Next] (Aici etrierul se va deschide.) [Done, Go back!] Acum se pot inlocui placutele de frana

Descuiarea automata a masinii dupa scoaterea cheii din contact CODE [Select] [46 - Cent. Conv.] [10 - Adaptation] Channel 04: Auto Unlock after removing the key (1 = Activate / 2 = Deactivate) [Test] 20


[Save] [Done, Go Back] Optional se mai pot seta ca la inchiderea/deschiderea masinii sa se aprinda avariile sau sa se auda un clacson scurt Pt acestea, modificari si: QUOTE (Optional channels - flash blinkers or sound horn) Canalul 03 Auto Lock Canalul 04 Auto Unlock Channel 05: Unlock, horn sounds (1 = Activate / 2 = Deactivate) Channel 06: Lock, horn sounds( 1 = Activate / 2 = Deactivate) Channel 07: Unlock, turn signals flash (1 = Activate / 2 = Deactivate) Channel 08: Unlock, turn signals flash (1 = Activate / 2 = Deactivate)

Dezactivare avertizor sonor centură de siguranţă

(ATENŢIE! POATE AFECTA SIGURANŢA CIRCULAŢIEI!!!): Control Module Coding Select 17 (Instrument Cluster) Coding -> Function 07 00??x0x: Extra-Options +01 - Brake Pad Warning active +02 - Seatbelt Warning active +04 - Washer Fluid Warning active +16 - Sedan (Jetta) scazi 2 din 7 So if you wanted everything active.... 0023x0x where x is the value of the original coding, let's say it was set there from the factory. To remove seat belt warning, just subtract the 02.... so it would now be: 0021x0x 21


My stock coding: 0023203 With no seat belt chime: 0021203

Închiderea pistoanelor dupa inlocuirea placutelor de frana pe spate CODE [Select] [53 - Parking Brake] [04 - Basig Settings] Grup: 007 [Start!] Activating basic settings [CON/DEC/Next] (Aici etrierul se va inchide.) [Done, Go back!] Aici este invers, cel putin la mine. 007-deschidere etrieri 006-inchidere etrier

Incuierea automata a uşilor dupa viteza de 15km/h CODE [Select] [46 - Cent. Conv.] [10 - Adaptation] Channel 03: Auto Lock after 15km/h (1 = Activate / 2 = Deactivate) [Test] [Save] [Done, Go Back]

Închidere automata a geamurilor tinand apasat butonul doar 2 secunde CODE [Select] 22


[46 - Central Conv.] [07 - Coding] [Long Coding Helper] Byte 6: - bifati Bit 6 (Comfort function autom. closing) [Transfer Coding!] [Do It!] Click on each of the Byte numbers in step 3) and you'll see the selectable options below. - debifati bit "Comfort function power windows/sunroof via remote control inactive" - bifati bit "Comfort opening power windows via remote control active" - bifati bit "Comfort closing power windows via remote control active" - bifati bit "Closing sunroof via remote control active" [Transfer Coding!] [Do It!] Timer-ul pentru faruri cat sa stea aprinse il gasesti in adaptari in Central Electric [nu in long codding] -Activat ridicare automata geamuri( fara sa mai tii apasat pana ajung sus) Bifezi la centrala electrica CONFORT CLOSING ACTIVE Pentru ridicare geamuri tinand apasat butonul 2 secunde trebuie bifat : Comfort function automatic closing . Pt setarea timpilor ls CH/LH am intrat la adaptation, insa nu imi da voie sa schimb timpii... setez cat vreau eu dar cand dau save si ce mai e acolo se reseteaza valorile puse de mine.... Cat desprea restul setarilor...trebuie sa umblu iar cu vagcomul sa vad unde sunt...am stat o zi intreaga si m-am jucat pe acolo...si ce am gasit interesant am activat... O sa postez si procedura exacta... Oricum este in central electric si central convenience..... eu am luat la rand fiecare bit in parte si am vazut ce scrie pe acolo...si am activat ce m-a interesat Inchidere proiectoare cand dai flash sau faza lunga by Riddler CODE [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 17: bifati Bit 5 (Front Fog lights deactivated with High Beam) 23


[Transfer Coding!] [Do It!]

Lumini de poziţie faţă stil US (cu lămpile de semnalizare) Sa stea aprins becul de semnalizare din far, la o intensitate mai mica si atunci cand aprind pozitiile. Am inteles ca pe Golf 5/ jetta, modelul pentru America ,exista aceasta codare. Colegul Popilam stie mai multe. Central Electric / Long coding / Turn Signals As Parking Light xxx % . Setezi cat la % sa iti stea semnalele aprinse .... asa dai impresia ca bagheta este in totalitate aprinsa

Lumini de poziţie spate stil DONUTS (cu centrul stins): CODE [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 9: Debifati toate casutele sau modificati casuta DEC in cifra 0 (zero) [Transfer Coding!] [Do It!] stie cineva codul la care sa revin la stopurile standard (casuta DEC ca sa nu mai aiba cifra zero, trebuie inainte sa introduc un cod, ceva de genul: 00010100, nu mai stiu exact dar ceva de genu')

Modificare mile in kilometri (USA/Canada/Uk/Europa/Japan) Inainte de a face orice modificare notati-va valoarea existenta. Folosirea gresita a adaptarilor poate conduce la nefunctionalitatea motorului, asa ca orice modificare o faceti pe propriul risc ! [Select] [17 - Instruments] 24


Notati-va valoarea Soft coding. Ea reprezinta valoarea presetata si in cazul in care nu obtineti rezultatele asteptate puteti reveni la aceasta valoare. [Recode - 07] modificati valoarea din campul software coding dupa cum urmeaza: [Do It!] Urmariti digitii din cod (xxyzw). Al treilea digit din codarea software (..y..) reprezinta piata de destinatie si aduce urmatoarele modificari: 1 - "EU" ceasul in format 24 ore (modifica afisarea distantei parcurse in Kilometri la modelele dupa 2002) 2 - "USA" ceasul in format 12 ore (modifica afisarea distantei parcurse in mile) 3 - "Canada" ceasul in format 12 ore (modifica afisarea distantei parcurse in Kilometri la modelele dupa 2002) 4 - "UK" ceasul in format 24 ore (modifica afisarea distantei parcurse in mile) 5 – Japan 6 - Saudi Arabia 7 – Australia [Save]

Modificarea sunetului alarmei [Select] [46 - Cent. Conv.] [10 - Adaptation] Channel 10: Alarm Horn Aici alegi între biţii 0,1,2,3 care-ţi convine. [Save] [Done, Go Back] Sunt două feluri de tonalităţi grupate pe biţii 0 şi 2 (seamănă cât de cât a alarmă) şi pe biţii 1 şi 3 (piuie) şi dacă-mi amintesc bine, din cele două grupuri de sunete pe biţii 1 şi 3 se aude mai tare. Select] [46 - Cent. Conv.] [10 - Adaptation] 25


Channel 10: Alarm Horn -la mine este Channel 13: Alarm Horn la channel 10 e altceva am incercat si eu si nu merge sa schimb ......

Modificarea limbii pe afisajul display-ului CODE [Select] [17 - Instruments] [10 - Adaptation] Channel 02 : 00001 - German 00002 - English 00003 - French 00004 - Italian 00005 - Spanish 00006 - Portuguese 00007 - no text 00008 – Czech [Test] [Save] [Done, Go Back]

Regenerarea filtrului de particule (DPF). NOTA: Aceasta procedura se efectueaza NUMAI in cazul in care procedura descrisa in manualul de utilizare a autovehiculului nu functioneaza!! Testat pe motor de 2.0 TDI 140 cp., functioneaza cu Vag Com 805 sau 812.4 Contactul PUS, motorul pornit (IMG:style_emoticons/default/wink.gif) , apa peste 50 grade ( vezi temperatura in Measuring Blocks canalul 002 , campul nr 4) A se urmari valorile DPF in Measuring BLocks canalul 075 , casuta nr 3. În cazul în care valoarea de încărcare este de peste Specificaţii (din casuta numarul 2), atunci filtrul trebuie inlocuit, altfel poate crapa in timpul regenerarii. Consumatorii electrici si mecanici anexati motorului sa fie porniti (incalizre scaune, clima, lumini, etc, etc) 26


EGT-ul ( gazele de evacuare INAINTE DE TURBINA ) sa fie peste 700 °C inainte de a porni testul. CODE [Select] [01 - Engine] [Coding-II - 11] ( doar varianta 805 stie aceasta optiune ) • Activeaza Regenerarea prin introducerea codului 21295. [Do It!] [Meas. Blocks - 08] selecteaza Groups-canalele 070 and 075. [Go!] Semnificatii : Canal 070 casuta nr. 1: Regeneration Status (xxxxxxx1 = Normal Regeneration active, xxxxxx1x = Forced Regeneration active) Canal 070 casuta nr. 3: Regeneration Counter/Timer Durata Canal 075 casuta nr. .1: EGT inainte de turbina Canal 075 casuta nr. 2: EGT inainte de Particle Filter Canal 075 casuta nr.3: Incarcarea Particle Filter - Particle Filter Load Canal 075 casuta nr.4: EGT dupa Particle Filter Porniti si urmariti valorile mentionate mai sus. Se ruleaza masina cu 30-60 km/h - la 1500-2500 rot/min ,durata aprox. 15-20 Minute . Sofati pana cand Particle Filter Load devine cat mai aproape de valoarea 0% (dar in intervalul de timp mentionat). Daca valorea nu scade atunci conditiile de rulare nu sunt corespunzatoare cu datele de aici sau motorul tau are probleme mecanice sau electronice ( supape, tacheti, axa cu came, injectoare, compresie - sau debimetru, senzor apa, actuatori turbo/egr)

Reglarea sensibilităţii direcţiei în funcţie de viteză Este vreo procedura Vag-Com prin care se poate face ca la viteza mai mare de X km/h sa se intareasca volanul/directia? pt k mi se pare mult prea sensibil volanul de la 120km/h in sus. 27


Este asa ceva doar la sistemele de directie asistate electronic. Se ajusteaza undeva cu vagcom-ul pe o scara de la 0 la 6. Imi pare rau dar nu mai stiu exact procedura. Voi reveni cu informatii Select 44 (Steering Assist) --> 10 Adaptation Read channel 1. Lower numbers are harder steering, higher numbers are easier. Range is reported to be between 0 and 6. Dar cred ca este valabil doar pt auto din 2007 pana in present

Testul catalizatorului Pentru a face aceste teste intrati in modulul de control ptr motor.Blocurile 002,030,032 si 033 sunt facute in blocurile de masuratori( measuring blocks) in timp ce blocurile 036, 034 si 046 sunt facute in setarile de baza (basic settings).Varianta de test descrisa este ptr motoarele VR6 iar ptr motoarele 1.8T difera putin si anume ptr motoarele cu seria motor AWD, AWW se ridica turatia la 1800-2200 si se tine apasat constant.La varianta de motor AWP se apasa pedala de frana si se tine apasata si apoi se apasa pedala de acceleratie la "podea" si se tine astfel.Turatia motorului chiar la blana nu va creste peste 2000 ture( asa spun oamenii care au facut-o). BLOC 002 LOAD REGISTRATION verificati citirea MAF (mass air flow sensor) la relanti.Motorul trebuie sa fie la temperatura de regim si cu AC-ul oprit.Mergeti in blocul 002 si cititi valoarea in campul 4 ( field 4).Valoarea la relanti trebuie sa fie intre 1 si 25g/s.Daca este mai mica decat 1 g/s atunci este o scaparde aer fals in tubulatura de aer. BLOC 030 OXYGEN SENSOR REGULATION Mergeti in blocul 030.Field 1 este un numar din trei digitzi care indica starea senzorului de O2 pre-cat.Field 2 este pentru senzorul post-cat.Acest numar din trei spune daca incalzirea sensorului functioneaza si de asemeni daca sensorul functioneaza ca atare sau nu.Valoarea trebuie sa fluctueze intre 111(sensor incalzit)si 011 ( sensor neincalzit).Ultimele doua digit-uri pot fluctua intre 0 si 1 dar ar trebui sa fie predominant 1. BLOC 032 OXYGEN SENSOR CONTROL LEARNED VALUES Mergeti in blocul 032. Field 1 indica amestecul la relanti si Field 2 indica amestecul la sarcina partiala ( in mers de ex.)Valoarea tre sa fie intre -10% si +10%.Valoare negativa amestec bogat, valoare pozitiva - amestec sarac.Daca valoarea este la cca +25% ( valoarea superioara limita) atunci MAF sensor este terminat( gunoi).Daca valoarea este intre +10% si +25% atunci sensorul O2 pre-cat este terminat sau exista aer fals in galeria de admisie 28


sau MAF sensor este terminat.Valoarea in general ar trebui sa fie undeva la +1.6%, +1.8% ca toate sa fie OK. BLOC 033 PRE-CAT OXYGEN SENSOR CONTROL Mergeti in blocul 033.Valoarea data in Field 1 este reprezinta controlul sensorului O2 precat.Aceasta valoare trebuie sa fluctueze cel putin cu 2% in intervalul -10% si +10% BLOC 036 POST-CAT OXYGEN SENSOR CONTROL Mergeti in blocul 036( acest test trebuie facut in basic settings si nu in measuring blocks).Apasati si tineti asa pedala de frana ptr ca testul sa se autoinitieze.Turatia motorului ar trebui sa creasca la cca 1400rpm.In Field 1 este valoarea voltajului pe sensorul post-cat.Trebuie sa fluctueze usor intre 0 si 1V.Field 4 va spune de asemenea" TEST ON/OFF" inainte sau in timp ce testul ruleaza si de asemeni "B1-S2 OK" ( sensor bun) sau "B1-S2 NOT OK" ( sensor terminat) dupa ce testul s-a terminat.Ridicati piciorul de pe pedala de frana dupa ce testul s-a terminat. BLOC 034 AGING OF PRE-CAT OXYGEN SENSOR ( VARSTA SENSORULUI DE 02 PRE-CAT) Mergeti in blocul 034( testul trebuie facut in basic settings si nu in measuring blocks).Apasati si tineti asa pedala de frana.Turatia motorului ar trebui sa urce la cca 1400 rpm.In Field 1 este turatia motorului.In Field 2 este temperatura catalizatorului.Valoarea din Field 3 spune cat de imbatranit este sensorul O2.In Field 4 va aparea ca si in blocul 036 "test on/off" , "B1-S1 OK" sau B1-S1 NOT OK".Valoare care ne da gradul de imbatranire al sensorului trebuie sa fie deasupra de 0,80.Valoare ptr un sensor nou este 1.99.Valoarea scade odata cu varsta sensorului.Ridicati piciorul de pe pedala de frana dupa terminarea testului. BLOC 046 CATALYTIC CONVERTER ( VERIFICAREA CAT-ULUI DACA MAI E BUN SAU NU). Mergeti in blocul 046 ( testul trebuie facut in basic setting si nu in measuring blocks).TESTUL 034 TREBUIE FACUT IMEDIAT INAINTE DE ACEST TEST (046) ACESTA SA SE POATA AUTOINITIALIZA. Apasati si tinesi asa pedala de frana ptr ca testul cat-ului sa porneasca automat.( cat-ul trebuie sa se incinga la cca 400 grade C ca sa se obtina o citire exacta).Turatia motorului ( Field1) trebuie sa creasca la cca 1400 rpm.Field 2 este temperatura cat-ului.Aceasta de asemeni se va ridica in timpul testului.Field 3 arata capacitatea de conversie a catalizatorului ( starea lui).Daca cat-ul este bun atunci valoarea tre sa fie undeva sub 0.50 la terminarea testului.Field 4 va indica daca cat-ul mai este sau nu bun si anume "CAT B1 - OK" sau "CAT B1 - NOT OK".Ridicati piciorul de pe pedala de frana imediat ce testul se termina. Cum am spus la inceput aceasta este varianta de veruificare ptr un motor VR6.La 1.8T am dat detalii la inceputul paginii.Ptr motoarele de Europa, 1.4, 1.6 varianta de test ar trebui sa fie aproape la fel.Ramane doar sa intrebati la dealer sau la cine stie daca se apasa sau nu 29


pedala de frana in timpul testului sau daca se tureaza motorul la blana in timpul testului sau doar la 2000 rpm.In rest testul este la fel ptr toate. Ca ti-a iestit in 030 campul 2 110 si nu are fluctuatii din cate stiu eu senzorul nu da semne ca se incalzeste, dar se poate sa gresesc iar in legutura cu partea mea sa stii ca am plecat de la 200 si ceva de grade cu piciorul pe frana si a urcat pana la 392, am tinut cateva minute in jur de 2-3000 dar temperatura a scazut la 360 si ceva. Poate ar trebui sa umblu cu masina putin sa ridic temperatura. M-am documentat si am gasit ca 110 inseamna de la dreapta la stanga (1=ON, 0=OFF): prima cifra: "sensor heating", a doua cifra "sensor ready", a treia cifra "control active" Deci eu am la S2 control active OFF.

30

Proceduri VAG COM

Recommend Documents