031110 031015
Section 5
Industrial & Marine Engines
Engine data Industrial diesels 12-series with EMS Contents Engine program.................................................................................................... 3 Standard equipment ............................................................................................. 3 Basic data ............................................................................................................. 4 Technical data and cooling equipment recommendation..................................... 6 DI12 54A, order ref. 10-70................................................................................ 6 DI12 56A, order ref. 10-71................................................................................ 8 DI12 56A, order ref. 10-72.............................................................................. 10 Basic dimensions DI12................................................................................................................. 12 Equipment list .................................................................................................... 14
Part No. 1 588 878
© Scania CV AB Sweden
Industrial & Marine Engines
2
Part No. 1 588 878
Industrial diesels 12-series with EMS
© Scania Industrial & Marine Engines
DHA Section 5.
031110
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 031015
Engine program 12 series engines with EMS for all-speed applications IFN, 2100 r/min
DI12 54A, order ref 10-70 1)
kW (hp)
243 (330)
DI12 56A, order ref 10-71
kW (hp)
272 (370)
DI12 56A, order ref 10-72 2)
kW (hp)
280 (381)
1)
Optimized for Clark´s 36000 transmission 2) Optimized for Clark´s 42000 transmission All engines comply with Stage 2 EURO exhaust emission regulations. Ratings IFN:
Intermittent service
Descriptions of ratings and other power information, see “General”
Standard equipment Unit injectors and EMS Coordinator Main Supply Box Fuel filter cartridge Turbo charger Air-to-water charge air cooler (DI engines). Oil cleaner Oil filter Oil cooler Alternator: 1-pole, 65A, 28 V, incl. relay and connection for tachometer, see “Equipment data” Starter: 1-pole, 6.7 kW, 24 V, see “Equipment data” Flywheel, see “Equipment data” Silumin flywheel housing, SAE1 flange, see “Equipment data” Front mounted engine brackets, see “Equipment data”. Mainly for transportation purposes Operator’s manual
031110
© Scania Industrial & Marine Engines
Part No. 1 588 878
3
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
Basic data General Configuration and number of cylinders Working principle Bore x stroke Displacement Compression ratio Firing order Piston speed at 1500 r/min at 1800 r/min Rotation, seen from flywheel end Moment of inertia with flywheel for 14” coupling Number of teeths on flywheel ring gear Weight approx., with fan but excl. oil and coolant
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 in-line . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 stroke mm . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 x 154 dm3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11,70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18:1 . . . . . . . . . . . . . . . . . . . . .1 - 5 - 3 - 6 - 2 - 4 m/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,70 m/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9,24 . . . . . . . . . . . . . . . . . . . . Counter clockwise kgm2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2,74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995
Lubrication system Oil capacity Oil consumption Oil change intervals Oil grade
Oil Pressure Normal Minimum permitted Oil temperature Maximum permitted Oil cleaner Filtration Oil filter for turbo charger Oil cooler
4
Part No. 1 588 878
dm3, min max g/kWh h
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 . . . . . . . . . . . . . . . . . . CE or CF acc. to API CCMC D5 Acea E3-96
bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6 bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0,7 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 . . . . . . . . . . . . . . . . . Paper and Centrifugal Micron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper . . . . . . . . . . . . . . . . .Water cooled/Full flow
© Scania Industrial & Marine Engines
031110
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
Injection system Type Governor Fuel filter
. . . . . . . . . . . . . . . Electronic Unit Injectors Scania Engine Management System (EMS) . . . . . . . . . . . . . . . . . . . Paper filter element
Cooling system dm3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 - 85 ..................................1 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Coolant volume, excl. radiator Coolant temperature Number of thermostats Opening temperature
Intake system Permissible pressure drop in intake system with cleaned or new filter Permissible pressure drop in intake system with blocked (dirty) filter
mmWc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 mmWc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
Electrical system, optional equipment Type Optional Starter, standard equipment Optional Alternator, standard equipment Optional
031110
. . . . . . . . . . . . . . . . . . . . . 1-pole, 24 V, DC . . . . . . . . . . . . . . . . . . . . . 2-pole, 24 V, DC . . . . . . . . . . . . . . . . . 1-pole, 24 V - 6.7 kW . . . . . . . . . . . . . . . . . 2-pole, 24 V - 6.7 kW . . . . . . . . . . . . . . . . . . . 1-pole, 28 V - 65 A . . . . . . . . . . . . . . . . . . . 2-pole, 28 V - 65 A . . . . . . . . . . . . . . . . . . . 1-pole, 28 V - 90 A
© Scania Industrial & Marine Engines
Part No. 1 588 878
5
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
Technical data and cooling equipment recommendation DI12 54A, order ref. 10-70 Engine speed, r/min
Rating acc. to
1200
1500
1800
2100
Gross power
kW (hp)
IFN
187 (254)
237 (322)
240 (326)
243 (330)
Gross torque
Nm (kpm)
IFN
1488 (152)
1509 (154)
1273 (130)
1105 (113)
195 (143)
193 (142)
193 (142)
222 (163)
3/4 load
199 (146)
199 (146)
194 (143)
229 (168)
1/2 load
199 (146)
205 (151)
205 (151)
241 (177)
102
129
137
179
to exhaust gas
130
165
164
205
to surrounding air
21
21
21
24
Spec. fuel consumption full load
g/kWh (g/hph)
Heat rejection to cooling water
kW
Air consumption
kg/min
14
22
25
30
Exhaust flow
kg/min
15
23
26
31
502
437
388
398
°C
Exhaust temperature
IFN, 2100 r/min Air-on temp. 35 °C
50 °C
m2
1.0
1.0
kg
55
55
dm /min
420
420
Puller
Puller
Radiator front area weight Coolant pump flow
3
Fan type Ø
mm
787
787
power losses
kW
21
21
1
1
1:1.08
1:1.08
m3/s
9.8
9.8
mm Wc
35
30
number of drive belts (poly-V) speed ratio Air flow free air flow pressure reserve
6
Part No. 1 588 878
© Scania Industrial & Marine Engines
031110
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
DI12 54A, order ref. 10-70 OUTPUT kW
280
380 hp 360
kW x 1.36 = hp
260 IFN 240
340 320 300
220
280 200 260 180
240 220
160 Max torque 1589 Nm/1400 r/min
TORQUE Nm Nm ---------- = kpm 9,81
1600
160 kpm
1400
140 IFN
1200 1000
120 100
IFN 220 SPECIFIC FUEL CONSUMPTION g/kWh g ⁄ kWh ------------------ = g ⁄ hph 1,36
031110
160 g/hph
210 150
200 190 1200
1400
1600
1800
© Scania Industrial & Marine Engines
2000
140 2200 r/min
Part No. 1 588 878
7
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
Technical data and cooling equipment recommendation DI12 56A, order ref. 10-71 Engine speed, r/min
Rating acc. to
1200
1500
1800
2100
Gross power
kW (hp)
IFN
200 (272)
272 (370)
272 (370)
272 (370)
Gross torque
Nm (kpm)
IFN
1592 (162)
1732 (177)
1443 (147)
1237 (126)
197 (145)
190 (140)
192 (141)
214 (157)
3/4 load
202 (149)
200 (147)
197 (145)
224 (165)
1/2 load
207 (152)
206 (151)
207 (152)
238 (175)
109
138
145
180
to exhaust gas
143
186
186
222
to surrounding air
23
24
23
26
Spec. fuel consumption full load
g/kWh (g/hph)
Heat rejection to cooling water
kW
Air consumption
kg/min
14
22
27
33
Exhaust flow
kg/min
15
23
28
34
549
464
401
393
°C
Exhaust temperature
IFN, 2100 r/min Air-on temp. 35 °C
50 °C
m2
1.0
1.0
kg
55
55
dm /min
420
420
Puller
Puller
Radiator front area weight Coolant pump flow
3
Fan type Ø
mm
787
787
power losses
kW
21
21
1
1
1:1.08
1:1.08
m3/s
9.8
9.8
mm Wc
35
30
number of drive belts (poly-V) speed ratio Air flow free air flow pressure reserve
8
Part No. 1 588 878
© Scania Industrial & Marine Engines
031110
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
DI12 56A, order ref. 10-71 OUTPUT kW
300 400 hp
kW x 1.36 = hp
IFN
280
380 360
260 340 240 320 300
220
280 200 260 180
240 Max torque 1780 Nm/1400 r/min
TORQUE Nm Nm ---------- = kpm 9,81
1800
180 kpm
1600
160
1400
IFN
1200
140 120
IFN
160 g/hph
210 SPECIFIC FUEL CONSUMPTION g/kWh g ⁄ kWh ------------------ = g ⁄ hph 1,36
031110
150
200
140
190 180 1200
1400
1600
1800
© Scania Industrial & Marine Engines
2000
2200 r/min
Part No. 1 588 878
9
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
Technical data and cooling equipment recommendation DI12 56A, order ref. 10-72 Engine speed, r/min
Rating acc. to
1200
1500
1800
2100
Gross power
kW (hp)
IFN
224 (305)
294 (400)
294 (400)
280 (381)
Gross torque
Nm (kpm)
IFN
1783 (182)
1872 (191)
1560 (159)
1273 (130)
200 (147)
193 (142)
196 (144)
217 (160)
3/4 load
201 (148)
199 (146)
195 (143)
223 (164)
1/2 load
205 (151)
204 (150)
205 (151)
237 (174)
127
155
163
198
to exhaust gas
160
206
210
240
to surrounding air
26
26
26
28
Spec. fuel consumption full load
g/kWh (g/hph)
Heat rejection to cooling water
kW
Air consumption
kg/min
15
23
28
33
Exhaust flow
kg/min
16
24
29
34
567
486
431
425
°C
Exhaust temperature
IFN, 2100 r/min Air-on temp. 35 °C
50 °C
m2
1.0
1.0
kg
55
55
dm /min
420
420
Puller
Puller
Radiator front area weight Coolant pump flow
3
Fan type Ø
mm
787
787
power losses
kW
21
21
1
1
1:1.08
1:1.08
m3/s
9.8
9.8
mm Wc
25
20
number of drive belts (poly-V) speed ratio Air flow free air flow pressure reserve
10
Part No. 1 588 878
© Scania Industrial & Marine Engines
031110
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 030401
DI12 56A, order ref. 10-72 OUTPUT kW
300 400 hp
kW x 1.36 = hp
280
380 IFN 360
260 340 240 320 300
220
280 200 260
2000 TORQUE Nm Nm ---------- = kpm 9,81
Max torque 1937 Nm/1400 r/min
190 kpm
1800
180
1600
160 IFN
1400 1200
120 IFN
220 SPECIFIC FUEL CONSUMPTION g/kWh g ⁄ kWh ------------------ = g ⁄ hph 1,36
031110
140
160 g/hph
210 150
200 190 1200
1400
1600
1800
© Scania Industrial & Marine Engines
2000
140 2200 r/min
Part No. 1 588 878
11
DHA Section 5.
Industrial diesels 12-series with EMS
Industrial & Marine Engines Latest modification date: 030401
Basic dimensions DI12 Function of xyz-coordinates is found in “Equipment data”. 1. Fuel inlet (Insert connection for plastic pipe Ø 12 mm)* 2. Fuel return (Insert connection for plastic pipe Ø 12 mm)* 3. Air intake (Ø 101.6 mm)
x ~ -783 y ~ -296 z ~ +414
x y z
-947 +293 +359
4. Exhaust outlet
x y z
-702 +293 +359
5. Oil filler*
x y z
-1077 -73 +676
x y z
-634 -58 -437
x y z
-1259 +365 +79
x y z
-1111 +278 +465
x y z
-1177 +287 +337
2
6. Oil dipstick* 7. Oil drain plug 8. Connection for engine speed sensor (2x) 9. Coolant inlet (pipe Ø 57 mm) 10. Coolant outlet (pipe Ø 57 mm) 11. Drain tap for coolant 12. Connection to expansion tank (pipe Ø 32 mm) 13. To cab heater inlet 14. From cab heater outlet 15. Oil pressure sensor 16. Connection for coolant temperature sensor/monitor (2 x M14x1.5)*
z-
z
z+
x ~ -325 y ~ -296 z ~ +103
15
1 7
8
4
x-
x
10
3
x+
5
12
14 9
x+
x
x-
11
16
6
*Further information in “Equipment data”.
z-
z
z+
13
y-
12
Part No. 1 588 878
© Scania Industrial & Marine Engines
y
y+
031110
DHA Section 5.
Industrial diesels 12-series with EMS
Industrial & Marine Engines
Latest modification date: 030401
Dimensional drawing DI12 252
779
399
1434 - 1456 depending on fan type
Drawing No. 1 520 626 This sketch is intended only as general sales information and must not be used for any installation purposes. See also “General” * The values for center of gravity applies for engines with standard equipment including coolant. Cooling equipment such as fan, fanring and protective grating are not included.
403
379
~ 210*
~ 0*
396
~ 610*
031110
© Scania Industrial & Marine Engines
360
Part No. 1 588 878
13
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
Latest modification date: 031107
Equipment list S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
10
ENGINE WITH STANDARD EQUIPMENT
Ref
Description
-70
DI12 54A DI12 56A DI12 56A
-71 -72
36
37
41
45
46
Drw No.
243 (330) 272 (370) 280 (380)
1 520 626 1 520 626 1 520 626
MAIN SUPPLY BOX -02 S Cable harness, length 2 meter -03 O Cable harness, length 8 meter -04 O Cable harness, length 12 meter
1 505 526 1 505 526 1 505 526
COORDINATOR -02 S With
1 505 545
THROTTLE CONTROL -30 S Without -31 O Accelerator position sensor + cable harness 2 meter -32 O Accelerator position sensor + cable harness 8 meter
1 364 185 1 364 185
FLYWHEEL -01 S For use with truck clutch -10 O SAE 14” -11 O For Clark 15/16”
Pilot hole Ø 62 mm Pilot hole Ø 80 mm Pilot hole Ø 52 mm
FLYWHEEL HOUSING -01 S Measurements according to SAE1
Material: Silumin
49 -01 -19 -21 -22 -25 -26 -27 -28
14
IFN, kW (hp)
ENGINE SUSPENSION S Front mounting brackets O Fixed suspension, low O Fixed suspension, power pack type O Fixed suspension, power pack type O Stiff rubber suspension, low O Stiff rubber suspension, low O Stiff rubber suspension, power pack type O Stiff rubber suspension, power pack type
Part No. 1 588 878
Front brackets only Front suspension only Front suspension only
© Scania Industrial & Marine Engines
1 402 380 (B) 1 390 317 (B) 1 521 690
1 403 464
1 402 865 1 402 865 1 402 865 1 402 865 1 402 865 1 402 865 1 402 865 1 402 865
031110
Industrial & Marine Engines
Industrial diesels 12-series with EMS
DHA Section 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
51
AIR CLEANER
Ref -01 -25 -45
Description
Drw No.
S Without O Light duty, with paper insert. Filter area 10.6 m2 O Medium duty, with paper insert and precleaner. Filter area 16 m2
For separate mounting
1 399 298
For separate mounting
1 399 298
51A SAFETY CARTRIDGE FOR AIR CLEANER -00 S Without -01 O Safety cartridge for medium duty air Only for 51-45 cleaner 55
56
1 399 298
TURBO CHARGER -02 S Side mounted turbo charger, low -21 O Side mounted turbo charger, high EXHAUST PIPE -00 S Without -11 O Pointing rearwards -21 O 90° bend
57 -00 -40 -41 -42 -43 -51 -52 -53 -54
58 -00 -31 -32 -33 -34 -36 -37
031110
1 403 464 1 405 277
With exhaust brake, req 55-02 Ø 114, adjustable direction.
1 424 506 1 424 507
EXHAUST FITTINGS, shipped loose O Without S Flange O Flange O Flange O Flange O Flange and compensator O Flange and compensator O Flange and compensator O Compensator for exhaust brake
Ø 89-102, not with 56-21 Ø 114, requires 56-21 Ø 130, requires 56-21 Ø 155, requires 56-21 Ø 114, requires 56-21 Ø 130, requires 56-21 Ø 155, requires 56-21 Requires 56-11
1 383 334 1 383 334 1 383 334 1 383 334 1 383 334 1 383 334 1 383 334 1 383 334
SILENCER, shipped loose S Without O Truck type with clamps O Truck type with flanges O Truck type with flanges O Truck type with flanges O Industrial type, with flanges O Industrial type, with flanges
Ø 115 Ø 115 Ø 130 Ø 155 Ø 130, straight outlet Ø 155, straight outlet
1 331 676 1 331 676 1 331 676 1 331 676 1 379 683 1 379 683
© Scania Industrial & Marine Engines
Part No. 1 588 878
15
Industrial & Marine Engines
Industrial diesels 12-series with EMS
DHA Section 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
60
OIL SUMP
Ref
Description
-05
S Deep front oil sump
-06
O Deep front oil sump
-07
O Low oil sump
Drw No.
Oil dipstick on left or right hand side. Drain plug on low left hand side. Oil dipstick on right hand side. Drain plug on low left hand side. Equipped for checking oil level with running engine. Oil dipstick on left or right hand side.
60A OIL DIPSTICK -01 S On right hand side (in oil sump) -02 O On left hand side in engine block. 61 -01 -02 -03 -03A
62 -01 -10 -11 -12
66
OIL DRAINING S With magnetic drain plug O With hand pump O With hand pump O With hand pump
CRANKSHAFT PULLEY -00 S Standard -14 O With 2 extra grooves
1 422 908
1 422 908
Not with 60-07
1 407 418 1 407 418
Not with 60A-02 or 60-07 Not with 60-07
1 403 464 1 407 419 1 407 419
Not with 60-07
Under Right hand side (delivered loose) Left hand side (delivered loose) With tap (delivered loose)
1 403 464 1 407 848 1 407 848 1 407 848
Ø 260 mm. For fan ratio 1:1,08 only
1 404 595
-15
O With 2 extra grooves
Ø 192 mm. For fan ratio 1:1,08 only
1 404 595
-16
O With 3 extra grooves O For poly-V belt
Ø 260 mm. Without fan only Ø 260 mm. For fan ratio 1:1,08 only
1 404 595 1 404 595
-17
16
OIL FILLER S In valve cover O On left hand side (in engine block) O In valve cover and on left hand side (in engine block), 1:st cyl O In valve cover and on left hand side (in engine block), 5:th cyl
1 422 908
Part No. 1 588 878
© Scania Industrial & Marine Engines
031110
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
72
FAN
Ref -01 -02 -03 -07 -08 -09 -10 -19 -20
75 -00 -21 -22 -25
Description
S O O O O O O O O
Without fan Prepared for fan Prepared for fan Puller Pusher Puller Pusher Puller Pusher
RADIATOR AND FAN COVER S Without O 0.75 m2 Not for DC engines O 0.75 m2 Not for DC engines O 1.0 m2
-26
O 1.0 m2
-35
O 1.2 m2 Not for DC engines O 1.2 m2 Not for DC engines
-36
Drw No.
75A LEVEL MONITOR -00 S Without -13 O Level monitor in expansion tank 76
80
Without radiator Ratio 1:1 Without radiator Ratio 1:1,08 Without radiator Ø 711 mm, ratio 1:1,08 Ø 711 mm, ratio 1:1,08 Ø 787 mm, ratio 1:1,08. Not with 92A Ø 787 mm, ratio 1:1,08. Not with 92A Ø 787 mm, ratio 1:1. Req alternator Ø 787 mm, ratio 1:1. Req alternator
1 385 758 1 385 757 1 385 760 1 385 759 1 385 760 1 385 759
With fan cover for fan Ø 711 mm
1 407 843
With fan cover for fan Ø 711 mm, frame and front grating With fan cover Not for fan Ø 711 mm With fan cover, frame and front grating. Not for fan Ø 711mm With fan cover, Not for fan Ø 711 mm and Ø 787 mm With fan cover, frame and front grating. Not for fan Ø 711 mm and Ø 787 mm
1 407 843
1-pole, with 75- only
FAN RING -00 S Without -21 O Fan ring with sealing -22 O As 76-21 but with protective grating STARTER -05 O Without -11 S 1-pole -14 O 2-pole
031110
1 407 843 1 407 844 1 413 544 1 413 545
1 342 316
1 407 485 1 407 485
6.7 kW 6.7 kW
© Scania Industrial & Marine Engines
1 413 727 1 413 727
Part No. 1 588 878
17
Industrial diesels 12-series with EMS
Industrial & Marine Engines
DHA Section 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
81
ALTERNATOR
Ref -03 -20 -22 -25
82
89
O S O O
Drw No.
Without 1-pole 2-pole 1-pole
65 A 65 A 100 A
INSTRUMENT PANEL -01 S With connector kit -40 O Panel, 2-pole -41 O Panel, 2-pole with cupboard
ENGINE HEATER -00 S Without -11 O 1100W / 220V, plug-in type -23 -24
90
Description
O 500W / 220V, external O 1500W / 220V, external
Req 80-, 81-
Approved for use in Sweden, Norway, Finland, Germany and Austria Approved for use in Sweden, Norway, Denmark, Finland, Germany, Austria, Switzerland, Iceland, Holland and Belgium
FRONT MOUNTED POWER TAKE-OFF Important! Max. total torque capacity for front end of crankshaft is 1200 Nm. Total torque demands for coupling and drive must never exceed this value. -00 S Without -20 O Stub shaft for connection of flexible For engine without fan only coupling Not with 66-15 or -17 Max torque 635 Nm
SIDE MOUNTED POWER TAKE-OFF -00 S Without -13 O 1,19 x engine speed -13A O Prepared for side mounted PTO
1 404 225 1 404 225 1 516 176
1 505 526 1 505 510 1 505 510 / 1 462 237
1 412 624 1 407 215 1 407 215
1 404 875
91
92
AIR COMPRESSOR -00 S Without -01 O 2-cylinder, liquid cooled, incl unloader valve
92A AC COMPRESSOR -00 S Without -01 O With 18
Part No. 1 588 878
SAE B, 2-hole, 13 teeth Note! see sect.7
1 405 720 1 376 355
Capacity 380 - 600 l/min at 2100 r/min. Air inlet not connected
1 520 638
Not with 72-09, -10
1 404 227
© Scania Industrial & Marine Engines
031110
Industrial & Marine Engines
Industrial diesels 12-series with EMS
DHA Section 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
93
HYDRAULIC PUMP
Ref -00 -12 -13
95
Description
Drw No.
S Without O Capacity: 16 l/min at 150 bar int., 25-30 bar cont. O Capacity: 22 l/min at 150 bar int., 25-30 bar cont.
PROTECTION COVERS -01 S Standard -04 O With covers for drive belts. -04 O With covers for drive belts.
98B CORRISION PROTECTION -00 S Without -01 O 10 litre corrosion inhibitor. 98C FUEL PRE-FILTER C-00 O Without fuel pre-filter
C-01 C-02
Without pressure reduction valve
1 404 226
Without pressure reduction valve
1 404 226
with 81- (alternator), Not with 72without 81- (alternator), Not with 72-
1 432 956 1 431 749
(mix water 90% with inhibitor 10%.)
Requires a pre-filter from an external manufacturer. If no filter is mounted, the engine warranty is not valid.
S Fuel pre-filter with water separator O Fuel pre-filter with water separator and heater
1 407 701 1 407 701
98P CONVERTER OIL COOLER -01 S Without -02 O Connection for converter 99 A-01 L-31 L-36 L-38 N-01 Q-31 Q-32 Q-33
031110
SPECIAL EQUIPMENT O Tool kit S Crankcase ventilation O Crankcase ventilation O Crankcase ventilation O Scania International Service O With parts catalogue x1 O With parts catalogue x2 O With parts catalogue x3
1 424 243
Open, direction downwards In valve cover, for external connection Internal ventilation
© Scania Industrial & Marine Engines
1 405 725 1 405 359
Part No. 1 588 878
19
Industrial & Marine Engines
Industrial diesels 12-series with EMS
DHA Section 5.
Ideas and opinions about this book? The ambition with this book is to give you all the information you may need working with Scania engines. However, there can be parts of this book that could be described in another way or some information you wish to be added. When you have suggestions for improvements, or you find faulty information, please copy this page, write down your opinions and send by telefax or mail to the adress below. Your remarks may help us to further improve the following editions. Thank you in advance for your co-operation
Sender: Suggestion / Remark:
Mail to
Scania CV AB Industrial and Marine Engines Dept. IMS S-151 87 Södertälje, Sweden
Telefax
Sales After sales
+46 - 8 55 38 29 93 (int) 08 55 38 29 93 (nat) +46 - 8 55 38 98 12(int) 08 55 38 98 12(nat)
Telephone +46 - 8 55 38 10 00 (int), 08 55 38 10 00 (nat) 20
Part No. 1 588 878
© Scania Industrial & Marine Engines
031110