264962145 3G SWAP Guideline

Network Modernization and Swap Planning Process Version 4.1

Page 2 of 49

DOCUMENT DESCRIPTION Title and version Reference Target Group Technology and SW release Related Service Items Service Item number Author Date Approver

Network Modernization and Swap Planning Process for BSS and RAN Radio Network Planning 2G, 2.5G, 3G

Karri Sunila 23.2.2009 Ville Salomaa / Eric Kroon / Pekka Ranta

CHANGE RECORD This section provides a history of changes made to this document VERSION

DATE

EDITED BY

SECTION/S

COMMENTS

3.1 4.0

23.2.2009 27.6.2011

Karri Sunila Lasse Vuokko

ALL ALL

4.1

24.10.2011

Lasse Vuokko

3.2, 3.4, 4.4, 5.1

NSN update Combined 2G and 3G swap planning documentation as one. General update. Added Site configuration plan section. Minor other updates.

Copyright © Nokia Solutions and Networks. This material, including documentation and any related computer programs, is protected by copyright controlled by Nokia Solutions and Networks. All rights are reserved. Copying, including reproducing, storing, adapting or translating, any or all of this material requires the prior written consent of Nokia Solutions and Networks. This material also contains confidential information which may not be disclosed to others without the prior written consent of Nokia Solutions and Networks.

Page 3 of 49

Table of Contents 1.

Scope.................................................................................................

2.

Introduction.........................................................................................

3.

Setup modernize project.....................................................................

3.1 3.2 3.3 3.4

Multivendor integration tests............................................................................................ Site configuration plan..................................................................................................... Swap strategy and roll-out plan....................................................................................... Project acceptance KPIs and drive test methods.............................................................

4.

Setup methods and tools....................................................................

4.1 4.2 4.3 4.4 4.4.1 4.4.2 4.4.3 4.4.4 4.4.5 4.5 4.5.1 4.5.2 4.6 4.7

Area information.............................................................................................................. Site visits – Technical Site Survey................................................................................... Radio network parameter planning.................................................................................. Create adjacency change procedure............................................................................. Adjacency creation tool................................................................................................. Define strategy for CI/LAC mapping during swap.......................................................... Data flow for creation of adjacencies............................................................................. Neighbour consistency check........................................................................................ Deletion of unused foreign objects................................................................................ Dataflow and schedule for swap.................................................................................... Data flow for creation of the network............................................................................. Consistency check of created WBTSs........................................................................... Deployment of the base station..................................................................................... Other system updates...................................................................................................

5.

Pre-modernize performance.............................................................16

5.1 5.2

Pre-swap network verification (drive test)...................................................................... Pre-swap KPI collection.................................................................................................

6.

Prepare databuilds............................................................................18

6.1 6.2

Master plan.................................................................................................................... Daily swap plan.............................................................................................................

7.

Prepare modernize BTS...................................................................19

7.1 7.2 7.3 7.4 7.5

Network creation........................................................................................................... Consistency check......................................................................................................... Foreign BTS – other vendor cells.................................................................................. Customer parameter translation.................................................................................... Check parameter settings in OSS.................................................................................

8.

Integrate...........................................................................................21

8.1 8.2

Radio network parameter implementation..................................................................... Adjacency handling.......................................................................................................

Page 4 of 49

8.3 8.3.1 8.3.2 8.4 8.4.1 8.5

Adjacency handling methods......................................................................................... Method - Create double adjacency lists......................................................................... Method - Delete and create adjacencies directly........................................................... Adjacency update preparation procedure...................................................................... Deletion of non-used adjacencies.................................................................................. Swap site verification.....................................................................................................

9.

Post Modernize.................................................................................25

9.1 9.1.1 9.1.2 9.2

Radio network performance monitoring during swap..................................................... Recommended Reporting Suite reports......................................................................... Handover performance - Neighbour relations................................................................ Post-swap network verification (drive test)....................................................................

10.

BSS specific considerations for swap...............................................27

10.1 10.2 10.3 10.4 10.4.1 10.4.2

Multilayer network.......................................................................................................... Combined Handovers.................................................................................................... 2G parameter cross-checks before swap...................................................................... Setup OSS performance monitoring.............................................................................. Standard 2G measurements.......................................................................................... Other 2G measurements...............................................................................................

11.

RAN specific considerations for swap..............................................31

12.

Multivendor parameter and KPI/counter mapping............................32

12.1 12.2 12.3

BSS KPI and parameter mapping references................................................................ RAN KPI and parameter mapping references............................................................... NSN default parameters................................................................................................

13.

Reference material from past projects..............................................34

13.1 13.2

BSS swap projects........................................................................................................ RAN swap projects........................................................................................................

Appendices...................................................................................................38 Appendix A – Templates for Technical Site Survey Summary (TSSR) and site verification drive test................................................................................................................................ Appendix B – Example of a master plan for 2G and 3G.................................................................. Appendix C – Standard configurations for a 2G swap..................................................................... Appendix D – Antenna conversion..................................................................................................

Page 5 of 49

Scope The scope of this document is to explain BSS or RAN swap procedure and preparation activities from the network planning point of view. Swap (multi vendor swap or network modernization) is replacing old or other vendor network equipment with new equipment. Optimization which is often done after swapping the equipment is a different project and is not described in details in this document. This document supports Flexi modernization cases and RG20/RU20 software level.

Introduction This document contains description of the network planning activities during the NSN BSS or RAN SWAP. This document is prepared based on the experiences derived from different SWAP projects in which NSN network is modernized or other vendor is replaced with NSN equipment. The network swap mainly consists of three main stages: 

Pre-swap activities



During swap activities



Post-swap activities.

From network planning perspective activities for a swap project at high level are presented in a figure below. The mandatory radio network planning activities are illustrated in the figure with solid drawn lines and they are required to be carried out for the whole SWAP area. Radio Network Parameter Planning and Implementation

Performance Monitoring

Radio Network Verification 1

Radio Network Optimisation (Optional)

Radio Network Verification 2

Radio Network Planning (Optional) Transmission Planning (Optional)

Figure 1. Overview of main network planning activities

Flow diagram in Figure 2 illustrates the main steps within a swap project. Steps 1-3 consists of pre-swap preparations, steps 4-6 consists of swap execution and phase 7 consists of post-swap activities. Each of these main activities are considered in separate chapters in this document.

Page 6 of 49

Figure 2. Flow diagram of a swap or modernization project

Setup modernize project There are simultaneous tasks to be done before the actual swap. The following steps are required for preparations of the network swap / modernization.

1.1 Multivendor integration tests In case of a vendor swap multivendor integration tests should be conducted in the customer’s network. The level of the tests should be decided based on the need for interoperability. If there is also a future need for interoperability in customer’s network then the target should be that all problems will get solved. On the other hand if there is only temporary need for interoperability then it might be enough to check if the functions such as handovers are working or not.

1.2 Site configuration plan Site configuration plan defines mappings from existing site configuration to a new configuration including number of TRX and carriers, baseband capacity, transmission configuration, and planned features that affect site capacity. Configuration mapping for TRX and carriers is usually one-to-one, unless capacity expansion is done together with the swap. Adding new TRX or carrier will impact RF or neighbor plan and this needs to be taken into account during the swap. If number of TRX or carriers is reduced, the cell capacity dimensioning should be verified based on earlier traffic to make sure there will be no RF blocking after the swap. For 3G site baseband capacity need to be considered. A mapping from existing baseband capacity to required new capacity can be derived if enough information is available, otherwise the baseband requirements have to be determined based on dimensioning. The baseband capacity requirements depend on amount of traffic, number of HSPA users, number and type of HSDPA and HSUPA schedulers, and also on some network parameters such as initial and maximum bitrates, release timers, ... Correspondingly in 2G use and allocation of SDCCH, GPRS/EDGE, AMR, and half rate need to be mapped from the existing setup to the new configuration.

Page 7 of 49

In vendor swap the requirements for site transmission may change. It need to be confirmed that the available transmission is sufficient for the new site, or if transmission need to be upgraded. Upgrades are likely to be required especially if site capacity is expanded during the swap. If any changes are made to the RF chain of the site, the impact of the changes should be analyzed by link budget calculations to understand the impact to site coverage area. The coverage impacting changes include changes in cell powers (maximum power, BCCH power, CPICH power), use and type of combiners, cabling, antennas, receiver sensitivity, use of MHA, and use of RRH.

1.3 Swap strategy and roll-out plan A roll-out plan defining what is swapped, when, and where need to be clearly defined before start of the project. Preferably the network elements should be swapped so that one continuous area is swapped at a time. This reduces potential problems due to inter-operability and also eases performance verification (OSS KPIs and drive tests). A roll-out plan could progress as in example in Figure 3. The roll-out plan can later be extended as a master plan which is followed throughout the project. All the actions causing breaks to service should be scheduled for non-busy time of the day. Week1

Day1

Day4

Day5

Week2

Day2

Day3

Week3

Figure 3, Example of a roll-out plan

It should also be agreed if any other network modifications are allowed during the swap or if the network is frozen for the swap period. If other modifications are allowed it should be taken care of that how these modifications are included to the swap process in order to avoid data inconsistency. If any KPI affecting network changes are made during the swap period that are not directly part of the swap, it should be agreed with the customer how potential impact to the swap acceptance KPIs is handled.

Page 8 of 49

1.4 Project acceptance KPIs and drive test methods Before starting a swap project it has to be defined how the project acceptance should be done. • Based on stats from the network (aggregations must be defined) • Based on drive tests Pre-swap KPIs including network statistics and drive tests should be collected before any actions have been done. KPI mapping between vendors should be confirmed and agreed before the swap project. In case of a vendor swap it is recommended to verify that the acceptance KPI formulas are as similar as possible and that the exact counter pegging within the KPI is similar. Other vendor counters may be triggering earlier or later than NSN counterpart, and be pegged to a different message or instance. Due to this some failure cases may be included in one KPI but not in the another KPI and cause a delta between the KPI value between two vendors. Since counter triggering points between vendors can be different all KPIs will not be 100% comparable. This should be mentioned before the swap and when required, new KPI threshold should be defined based on available information. Note that KPIs may also be RAN/BSS release specific. References to multivendor KPI mapping can be found from chapters and 1.33. If KPI criteria are not fulfilled, optimization must be done. How to perform optimization after swap should be defined with customer before the project. It may not be suitable to have same acceptance KPIs for all areas. If customer is requesting a long list of KPIs to cover all functionalities of the network in detailed level it is recommended to define a smaller area which is measured more deeply and if the results are acceptable then other areas do not need to have all KPIs but only generic system performance KPIs. Drive tests should also be limited in order to reduce the expenses. Measurement routes and methods need to be defined for acceptance and additional drive tests will be performed only if there are problems with network performance. Drive test setup need to be agreed before any testing is started. In this phase at least following should be defined • Tests to be performed (voice calls, data calls, locked to 2G or 3G, dual mode) • Availability of test number and type of calls (MTC/MOC, mobile to mobile or PLMN) • Required number and length of the calls • Data testing (only downlink or also uplink, FTP file size) • Use of scanner

Page 9 of 49

Setup methods and tools 1.5 Area information The purpose is to get familiar with the swap area. Inputs required from customer regarding the demographic distribution of the areas like commercial area, residential area, industrial areas, and main business centers.

1.6 Site visits – Technical Site Survey Technical site survey (TSS) needs to be done for each of the site to be swapped. The purpose of the TSS is to do a site audit and verify the information provided by the customer and to verify that the new equipment could be installed. This task will be performed by Network Implementation. The following site information is checked and recorded during TSS: 

Location (site co-ordinates)



Azimuth



Antenna tilt (Mechanical/Electrical)



Antenna type



Number of antennas



Height of the antennas



Site type (green field, rooftop, etc.)



Feeder type and length.



Combiners (By-pass, RTC, Wide Band Combiners 2:1, bias-T, …)



MHA configuration, if used



Availability of installation space



Power supply and battery backup



Physical access to the site



Site alert systems

Changes can be done if required. An example instructions for TSS for a GSM swap are described in Appendix A.

Page 10 of 49

1.7 Radio network parameter planning In order to ensure a safe swap with a high quality, a SWAP principle will be defined. The main purpose of defining the swap principle is to define whenever CI or LAC is needed to change during the swap and also how to handle the adjacencies during SWAP. In order to ensure an efficient and consistent radio network parameter planning process during a SWAP, NSN will use NetAct Plan Editor, which is especially designed for mass modification of the network. Optimized NSN specific default parameter sets for the different networks and environments in the SWAP area will be defined on basis of the customer’s default parameter sets for the old vendor network. References to other vendor’s parameter mapping to NSN can be found in chapters Error: Reference source not found and Error: Reference source not found. Fully one-to-one parameter mapping is not possible for all vendors, since available tunable parameters and their effects vary. If customer has any specific tuned parameter sets that cannot be mapped 100% to NSN network, these should be known and discussed with the customer before swap project to avoid negative surprises. The parameter setting for each cell is then generated by the parameter planning application on basis of the planned default parameter sets and the cell specific settings. In order to ensure that the swap is performed as smoothly as possible, it is recommended to prepare and download most of the radio parameters to the involved BTSs and BSCs/RNCs before the actual hardware is swapped. This is also to make sure that nothing changes during the swap. Also adjacency relations need to be maintained during the swap.

1.8 Create adjacency change procedure Adjacency handling is one of the most critical tasks in a swap project. In order to be able to maintain the normal handover traffic and possibility between all cells during the swap an intelligent procedure for defining and updating adjacencies must be defined. In case of a network modernization, all adjacencies can be copied as they are from the old site. A vendor swap instead may be complicated due to adjacency handling. Intra-system adjacencies need to be updated always when a neighbouring site has been swapped. Also inter-system (2G->3G and 3G->2G) adjacencies need to be updated both ways to the newly swapped cells. Most efficient way to do this is to prepare a specific macro or script (Adjacency creation tool, see 1.8.1) which can retrieve all neighbour relations for requested cell and also create input files with updated adjacency definitions for all the needed OSSs. If it is not possible to use vendor specific input files then Excel can be used and adjacencies are created manually. Some vendors allow more neighbours to be defined than NSN. In such case, use OSS HO statistics to choose the most important neighbours and make sure that those are implemented to the new NSN cells. Some post-swap optimisation for the neighbours may also be needed. Strategy how adjacencies are handled during the swap and adjacency handling responsibilities need to be agreed.

Page 11 of 49

1.8.1

Adjacency creation tool

Adjacency handling can be done manually or automatically during a swap. Manual adjacency handling is very resource demanding and the possibility of mistakes is high. Automatically adjacency handling by using a tool is the less resource demanding and the possibility of making a mistake is very low, if the tool is configured properly and the input is correct. Pay close attention to one-way neighbours if any defined. An example of a procedure for automatically adjacency handling is shown in Figure 4 and Figure 5. Outer Outer definition definition to to MSC's

Adjacency Plan Operators DB

Adjacency Tool

Adjacencies to be added in old Vendors OSS

Adjacencies to added in NSN

Download Adjacencies OSS

Master MasterPlan Plan Produce list of Foreign objects to be deleted NSN & Vendor 2

Update Swap Swop status in swap swop plan

Physical swap SWAP

Figure 4, An example of a procedure for automatic adjacency handling

Part of the adjacency definitions will be to the other vendors’ base stations and there is a need for creation of foreign objects in both OSS systems of old and new vendors’. Since network is under heavy modifications at the areas where vendor borders are located the procedure for adjacency handling is important for successful swap project.

Page 12 of 49

Old Vendor Area

NSN Area

F_B2

B2

F_A1

A1 F_C1 F_B2 C1 A1 is swapped to A2

B2

A2

NSN Area

F_C1 Old Vendor Area

F_A2

F_C1 F_B2

C1 C1 is swapped to C2 NSN Area B2

A2

C2

Figure 5, Illustration of the use of foreign cells during the swap

Adjacency creation tool should be able to do the following tasks: • Import existing pre-swap adjacency definitions for cell to be swapped including also incoming adjacencies • Create updated adjacency definitions according to changes that are made for swapped cells ie. updated BSC/RNC, carrier, LAC… • Create import files with updated adjacencies for all the vendors that are involved Sometimes it is not possible to create these updated import files directly for other vendors’ OSSs. In that case the format of the adjacency files should be agreed to ease the processing of the adjacencies.

Page 13 of 49

1.8.2 mapping during swap

Define strategy for CI/LAC

In order to select the most suitable strategy for handling of CI/LAC during the swap, following methods are evaluated: • New CI, same LAC • Same CI, new LAC • Same CI, same LAC • New CI, new LAC In the case of same CI and new LAC, the geographical LAC area can remain the same and only the numerical value changes. Often this is the easiest solution for swap, some other advantages of this are    

Easy planning with one LAC mapping rule All ‘new’ cells can be defined in both BSC/RNC and MSC before the actual swap All new adjacencies can be defined before the actual swap if neighbour list length allows Easy fallback possible in case of any problems

In every case where changes are made it should be taken care of that RAC, URA and SAC values are also updated accordingly as needed. Easy fallback possibility in case the new NSN BTS does not function properly should be ensured.

1.8.3 adjacencies

Data flow for creation of

Based on the roll-out plan from regions intra- and inter-system adjacency (Neighbouring Cells) data will be given to Implementation (OSS) in vendor specific input files. The data can be downloaded to the network from OSS before physical swap if double adjacencies are used. If all swapped adjacencies are to be deleted and recreated during the swap then adjacencies cannot be uploaded to the network beforehand but in any case they need to be delivered to Implementation (OSS) prior to the actual swap for verifications. Following neighbour updates are required:    

Update NSN intra-system neighbours to include swapped site as internal site, not external Update other vendors intra-system neighbours to include the swapped site as external site, not internal Add all inter-system neighbours to the new site as they were in the old site Update incoming inter-system neighbours to point correctly to the new site

One day before the actual swap all old adjacencies related to swapped cells should be queried from the OSSs. The order of the BTS swaps has to be known and for each individual swap there should be separate plans for deleting old adjacencies and creating new updated adjacencies. This task should be done with scripts (Adjacency creation tool, see section 1.8.1) that are able to read the adjacency data, prepare the modifications as specified and create input files for all systems that are involved.

Page 14 of 49

1.8.4

Neighbour consistency check

A log file taken during updating of adjacent cell data should be provided to planning for checking of errors. The OSS dump should be provided also after the successful physical swap for further consistency check and creation of new neighbours.

1.8.5 objects

Deletion of unused foreign

After a successful physical swap a list of foreign objects will be provided from Network Planning to Implementation. The foreign objects that are swapped should be deleted from the network, and it should be confirmed that no adjacencies anymore point to those foreign objects. If any such adjacencies remain, they should be corrected to point to the new site.

1.9 Dataflow and schedule for swap To allow an easy implementation of all network elements a good interface between the Radio Network Planning group (responsible for the parameter definition), the Network Operations group (responsible for the implementation of the parameters in the network) and the Roll Out Services groups (responsible for installation etc. of equipment on site) needs to be established.

-2 Weeks

-1 Week

Database provided to implementation

Creation of the Network in RNCs/BSCs

Dump from OSS downloaded and database transferred to NWP Plan Edit

Start of the physical swap

Database provided to implementation

Post-swap actions

Time Figure 6, Timeline for network creation

In principle the dataflow between the groups can be simplified as the following illustration shows:

Page 15 of 49

Figure 7, Dataflows for swap project

1.9.1 network

Data flow for creation of the

The NSN site database is prepared according to the swap sites information from customer’s OSS dump. Reference BTSs will be created in the RNCs/BSCs with recommended set of BTS parameters from planning, prior to creation of actual BTSs. The swap BTSs will be created in the

Page 16 of 49

NSN network by a macro or by using Plan Editor as per the information provided by Planning with reference to the default reference BTSs. • The Element IDs will be decided for implementation • OSS upload to be done after creation of all BTSs in the RNCs/BSCs Time Frame: It is recommended that all network elements be created in the OSS at least 2 weeks before the physical swap

1.9.2 WBTSs

Consistency check of created

After the upload of network data, Implementation (OSS) should provide network dump to planning for consistency check of the created BTSs, excluding adjacency plan as it will be implemented later. Time Frame: It is recommended to provide OSS dump to Network Planning at least one week before of physical swap.

1.10

Deployment of the base station

Actual deployment of the new base station is done following the standard procedures of the customer. Site documentation, hardware tests and measurements are performed as required.

1.11

Other system updates

There might be other external systems that are using cell parameter info and needs to be updated during the swap. Customer is responsible for these updates but it is good to include all needed actions to swap plan. Here are few examples of other external systems that would require actions during the swap: • Home Zone Billing –functionality • Area based KPI systems • Customer complaint / Error reporting systems • Business intelligence systems Updates are performed based on the information of actual swap times in master plan for swap (see 1.14).

Pre-modernize performance Before any swap actions are carried out, the previous performance of the network need to be recorded. This performance level will give a reference point for post-swap performance.

Page 17 of 49

1.12

Pre-swap network verification (drive test)

Prior to the SWAP, a network verification drive test will be carried out to evaluate the quality of the existing radio network. The drive test is intended to serve as reference for verification of the performance of the radio network after the SWAP has been completed. A test route, covering all relevant BTS's in the SWAP area and its border areas, is agreed between the customer and NSN. In the drive test NSN will be following the roads defined in the drive test cluster definition by the customer. After the pre-swap drive verify that the drive test data has good quality and enough data samples (e.g. number of calls, handovers, data throughput about what is expected, no failures due to test system...) and that all agreed test have been completed. A good pre-swap drive test is crucial for reference purposes since it cannot be repeated after the network swap has started.

1.13

Pre-swap KPI collection

Agree with customer which KPIs should be followed and monitored. Especially when a multivendor SWAP is done a proper KPI matching should be found prior to the project start. References to multivendor KPI mapping can be found from chapters and 1.33. Following KPIs are useful to follow before and after the swap. These could be found from RAN/BSS reporting suite system program report: For 2G: • TCH availability ratio • SDCCH performance • Voice call performance • Handover performance • (E)GPRS setup performance • (E)GPRS data volume and throughput • UL/DL RxQuality For 3G: • Cell Availability • RRC Performance • RAB AMR Performance • RAB UDI Performance • RAB PS Performance • Packet Call Performance • SHO Performance • HSDPA Performance • HSDPA Data Volume • HSDPA Serving Cell Change • HSUPA Performance • HSUPA Serving Cell Change Make sure to collect enough KPI history data from the swap area. Collect also BTS and cell level data to see if certain cell was performing poorly already before the swap. After swap it is important to check that traffic has not reduced and performance has not degraded. It needs to be highlighted that comparing the results between different vendor’s

Page 18 of 49

statistics is difficult due to differences in the way the counters are pegged. The pre- and postswap results could presented at cluster and cell level. Traffic related KPIs could be: For 2G: • SDCCH seizure attempts • TCH requests for a new call • UL/DL TBF allocations • Call time (voice) • (E)GPRS data volume • Total number of voice drops For 3G: • RRC Attempts • RRC Non Reg Attempts • RAB RT attempts • Call time (voice) • RAB NRT attempts • HSDPA selections • HSDPA data volume • HSUPA selections • Total number of voice drops Results are compared against pre-swap results with proper mapping as in pre-swap evaluation.

Prepare databuilds An approved method for BTS naming and sector number versus direction should be defined ahead of the project. Allocation of IDs and names such as SITE, BTS, CELL, TRX, LAPD, and BCF IDs and names should follow a predefined system. Depending on system, not all of the above mentioned IDs are required. Being able to build a good overview of the network by element IDs and name definitions will also ease the operation of the network. Usually same naming and ID allocation method that the customer has used before can be used. If changes are made, they should be clearly agreed with the customers to avoid misunderstandings.

1.14

Master plan

A master plan is used as the key reference for Network Planning in the swap. The master plan is created based on input from the operator. Information needed is site name, sector name, direction, system, and TRX configuration. A very important aspect in a swap is to have a common master plan. The master plan can contain all BTS in the swap area (existing and new BTS during the swap) and the corresponding configurations (existing and extensions). The master plan can also be used as an input for the adjacency handling. The master plan can also contain the BTS specific RF parameters that need to be implemented.

Page 19 of 49

All the needed parameters for BTS commission should be contained in the master plan. A list of mandatory parameters can be collected from the document ‘Commissioning Flexi Multiradio BTS’ which is part of the document ‘Nokia Solutions and Networks WCDMA RAN, Rel. RU20, Operating Documentation’ for 3G or document ‘GSM/EDGE BSS, Rel. RG20(BSS), Operating Documentation’ for 2G. The documents can be downloaded from references 1 and 2. Simplified examples of master plan for 2G and 3G are presented in Appendix B. The master plan can also provide information for Logistics, Roll-out plan, ET-plan (transmission plan) and for the Site creation process in Plan Editor (Access database). It is recommended that not only sites that are on air at the moment of swap are included in to the master plan, but also new sites coming to air during the swap period can be included. New sites can be treated as sites to be swapped and the data preparation (cell parameters and adjacencies) of those sites can be done together with the data preparation for the sites to be swapped. This will reduce overlapping work and also ease change management during the swap.

1.15

Daily swap plan

Based on the cluster information available the daily swap plan is prepared by Implementation. The daily swap plan should follow the roll-out plan. Regional project managers will provide this information to Network Planning and to the customer one week prior to the physical swap. Required data builds can then be prepared for sites according to the plan and agreed adjacency change procedure.

Prepare modernize BTS 1.16

Network creation

Before the swap can start the network needs to be created in the RNCs/BSCs. The Master plan is used as an input to generate the data needed for the creation of all network objects. The database will be provided to implementation as an Excel sheet using an agreed format, for example similar as in Figure 8. RNC_id WBTS_id 22 123

Cell_id

WBTS_Name Cell_name NameW NameW1

BSC_id BCF_id BTS_id BTS_Name Cell_Type LAC xxx

xxx

Xxxxxxx

1,2, 3 or 4

CI

xxx xxxxx

LAC Sector_id 1265 1 NCC

BCC ARFCN x

x

xxx

Carrier 10658

… …

Ch_Type BCCH, SDCCH ,TCH

Figure 8, Examples of site data for network creation

The cell creation will then start in the RNCs/BSCs. Creation will be done based on the data provided in the Excel sheet and according to the appropriate parameter templates depending on the cell type and mapping of the parameters (see 1.19). The actual site creation can be done with MML macros, after which BSC/RNC upload is done and rest of the parameters are

Page 20 of 49

implemented with PlanEditor. Alternatively the whole process can be done with Plan Editor and OSS CM tools. This database should be provided at least 2 weeks prior to the first physical swap.

1.17

Consistency check

Once the cells have been created in the RNCs/BSCs, a download of all the network elements from OSS will be done. This download will be integrated to the Master Plan using Plan Editor transfer facility and the data will then be checked and any inconsistency or missing information detected. Information about parameter assessment can be found from reference 3.

1.18

Foreign BTS – other vendor cells

In order to define out-going adjacencies from the swap area, foreign objects need to be defined in the OSS. The foreign objects needed in the OSS are found by identifying the adjacencies pointing out of the swap area to the cells of the other vendor. All cells to be swapped needs to be defined as foreign (the old vendor cells), in order to be able to perform a handover between the two systems during the swap period. Also adjacencies out of the swap area to other non-NSN area need to be defined as foreign neighbours. Foreign objects can be created automatically when downloading new adjacencies (When an adjacency contains information different from any cell defined in the actual OSS, OSS will automatically create a foreign object for that adjacency relation). Disadvantage of this method is that the created foreign objects are identified only by the CI and LAC. The advantage of this method is that it is fast and requires no extra work. It is also possible to create all foreign cells before the download of the adjacencies. The advantage of this method is that it is possible to identify the foreign cells by proper cell names. The disadvantage is that the method requires more manual work to type in all the foreign objects unless scripts are used to do it.

1.19

Customer parameter translation

Customer parameter translation process is done from the OSS dump, as they may not have default parameter settings for all cells. All cell specific parameters (cell ID, LAC, ..) are derived from the dump and used for preparing the swap database and default parameter sets for different types of cells.

Page 21 of 49

Old vendor default

NSN Default

Translation Process

NSN Global Experience

NSN Default definition

Figure 9, Principle of customer parameter translations

Note! One-to-one parameter mapping is not possible for all vendors. If customer has any specific tuned parameter sets that cannot be mapped 100% to NSN network, these should be known and discussed with the customer before swap project to avoid negative surprises.

1.20

Check parameter settings in OSS

Although the parameter transfer is implemented by RNC/BSC Engineers according to the default parameters set and cell specific parameters provided by the Network planning group with a Macro (Automated Process), it is recommended to cross-check the "ACTUAL" parameter settings in OSS before the real swap from the OSS after uploading of database from RNCs. Based on the daily swap plan the right sites can be checked. In case of problems in the created parameters, corrections are needed and can be requested to Implementation before the physical swap.

Integrate 1.21

Radio network parameter implementation

The radio network parameters will be implemented in the sites created in the RNCs/BSCs from 



A macro application running from the RNC/BSC MML with reference to pre-defined reference BTSs. Once the sites are created, OSS upload will be done for updating OSS database. This OSS database will be used for Parameter Planning Application (Plan Editor) for further modifications to the BTSs and RNCs/BSCs via OSS. The whole process can be done with OSS CM tools and Plan Editor. This is the recommended way and requires also less steps.

After the final parameters are planned with Plan Editor, the radio network parameters will be downloaded to the network via OSS. More about Plan Editor can be found from the reference 3.

Page 22 of 49

1.22

Adjacency handling

Adjacency handling is one of the most critical tasks in a swap. In order to be able to maintain the normal handover traffic and possibility between all cells during a swap an intelligent procedure for defining adjacencies must be defined. Input to the adjacency-handling tool is the adjacency plan and the master plan. The tool must produce an adjacency list for NSN and one for the old vendor. Adjacencies to NSN can be imported to OSS by using the "Planning File Transfer". Plan Editor is very suitable for generating this planning file. Since Plan Editor is based on an Access database, all tables needed to create the adjacencies can be imported to that database. Remember to update also inter-system adjacencies both ways. Outer definitions for MSC are very important if the swap is spread over several MSCs. It is a MSC supplier related item, when outer definitions in MSCs need to be updated. More information about neighbour planning can be read from the references 5-7.

1.23

Adjacency handling methods

There are two main methods for handling adjacencies during the swap: One is to create simultaneously adjacencies to/from old and new cells so that adjacencies do not need to be modified during the actual swap of a site. This method is not suitable for cases where adjacency lists are close to full because every adjacency should be doubled. Second possibility is to modify adjacencies immediately before and after the actual swap in such a way that all old adjacencies are transferred to new cell as they were before swap. The requirement for this method is well functioning methods for adjacency imports, deletions and creations. It is also possible to create common updated adjacency plan for all the cells that are to be swapped in near future like next night. The risk of this method is that if one of the swaps failures there is not easy way of doing rollback for the adjacencies of that site. These two methods for adjacency handling are discussed deeper in following paragraphs.

1.23.1 adjacency lists

Method - Create double

This method is suitable when the adjacency lists in the network are short and can be easily limited to 16 or under adjacencies per system. During swap you have to create a double handover list. To make such a double entry the maximum allowed neighbours per BTS is 16 (since the maximum is 32). Since the swap is performed as a one to one swap, the neighbour relations will be doubled during the swap. The new cells are assigned new LACs and CIs. The neighbours of the old vendor cells will be added to the neighbour list of new NSN cells. After the swap of the old vendor cell the neighbour relations should be deleted in old vendor RNCs but at the same time the new swapped cells

Page 23 of 49

should be added as a neighbour to its neighbouring cells. The principle of the neighbour relation swap is shown in figure below. Old vendor CELL

Old vendor

Old vendor CELL

CELL TO swap

NSN CELL New LAC & CI Figure 10, Neighbor relation swap

Since some cells have more than 16 adjacency relations, all adjacency relations cannot be implemented before the swap, but they will be added and deleted in small blocks. One block will contain the adjacency relations to be added or deleted for e.g. the next 2 days of the swap period. In Rural areas it is normally possible to add all adjacency relations before the swap (Adjacency swap period e.g. 5 days), but in urban areas the maximum of 32 measurement frequencies might be exceeded in some cells, especially in dual band or multi-layer areas. The adjacency relations to be added or deleted in the following swap period are handled by an adjacency tool developed by NSN especially for a swap project. One solution of adjacency handling during swap is to collect HO stats before swap and take the 16 cells where most of handovers have been done and temporary delete the rest of the neighbours. This way the degradation of quality is been minimized. The deleted neighbours should then be recreated after the swap. In case of a 2G swap, it should be noted that to be able to implement double adjacency relations in the systems (NSN and old vendor) before the swap, BSIC of the new cell must be changed. It is not possible to have 2 measurement frequencies with the same BSIC in the adjacency list. BSIC consist of NCC + BCC. There are two methods to change BSIC; either NCC or BCC. For example, NSN will change temporarily the NCC value and will fall back to the old once the swap is complete.

1.23.2 adjacencies directly

Method - Delete and create

If adjacency lists are full or close to full this method should be used. Before each swap all related adjacencies are deleted and new adjacencies are created for the new NSN cell as they were for swapped old cell. The advantage of this method is that all the results are final and the risk of errors due to temporary solutions is avoided. This method is also more flexible for the adjacency changes because adjacency exports are performed close to actual swap. The disadvantages are that the downtimes of the sites might be a bit longer due to adjacency updates depending on the performance of the OSSs that are involved. This method also requires good scripts that will generate adjacency input files for all systems.

Page 24 of 49

Figure 11, Simplified example of adjacency update procedure

1.24

Adjacency update preparation procedure

The procedure for preparing the adjacencies for the next period is resumed in this section. 1. Update Master plan (Last period=Swapped & check that all sites in the next period have the right planned swap date) 2. If needed, update Adjacency table from operators database 3. Run adjacency tool 4. Make outer lists for MSCs (optional) 5. Provide operator with adjacency information for the next period to be created in the old vendors' and inter-system OSSs 6. Delete all foreign adjacencies in OSS pointing to the sites that were swapped during the last period 7. Export the ADJACENT_CELL table using Plan Editor 8. Import adjacency file to OSS and Upload adjacencies to RNCs /BSCs

1.24.1 adjacencies

Deletion of non-used

Non-used adjacencies to e.g. old cells that have been swapped, can be easily deleted, by deleting the corresponding foreign objects of the old cells. This will clean up the adjacency plan after the swap. This applies to the method where double adjacencies are used. In other methods there should not be adjacency leftovers. Note! It is recommended to change the identification of the foreign cells after the swap (e.g. change CI/LAC or Cell name of swapped foreign object). This will make the network easier to operate from OSS.

Page 25 of 49

1.25

Swap site verification

Immediately after the physical swap of the site, drive test shall be performed. A quick drive test is done to verify the implementation of the correct RNP parameters. The drive test will ensure that handovers between the cells are working properly, sectors are not swapped, and that call set-up success rate and drop call rate meets the criteria agreed for the swap project. If any performance problems are found, troubleshooting for the particular cell or site will be performed using Reporting Suite Reports or other suitable tools. All the swapped sites are individually checked for problems related to: • CSSR • HO / SHO, preferably handovers to neighbouring foreign cells should be inluded • Coverage • Total cross feeders between the sectors • Partial cross feeders between the sectors The data for each swap site is recorded as a log file as well as saved as required by customer. Any found problems are forwarded to the BTS group for rectification. After problem solving has been confirmed by the BTS engineer the cells/sites are verified again. See also cluster tuning WI, reference 8. Example of 2G drive test template is in Appendix A.

Post Modernize 1.26

Radio network performance monitoring during swap

The purpose of this activity is to detect and correct any unintentional hardware or parameter deficiencies at the earliest possible time. In this way any temporary decrease in network quality is minimized. It is recommended to keep problem record during swap. All the problems encountered will be written down and will be solved with customer as soon as possible. However some performance degradation is expected at border of the swapped and old cells. This is due to multiple reasons such as:   

Inter-vendor SHO/HO success rate can be lower than intra-vendor At swap border number of location are updates increase. In 2G this may cause SDCCH blocking, as the cells are not dimensioned for LAC border. Using dynamic SDCCH allocation should minimize the impact Continuous adjacency updates due to the swap activity

General information about network KPI analysis can be found from reference 9.

1.26.1 Suite reports

Recommended Reporting

Page 26 of 49

KPI statistics from the OSS are used during the swap for evaluation of the basic performance of each cell. Some selected KPI's and criteria are defined in order to detect any unexpected hardware problems or wrong parameter settings. KPI statistics can also be used to evaluate the general area performance during the swap. It is recommended to use Benchmarking KPI during the swap. Needs for KPI analysis / Drive test analysis are always contract and project specific. Example of 2G KPIs are presented below. Official benchmarking KPI can be found from Jump portal, reference 10. KPI

Formula

Threshold (%)

SDCCH access probability

Csf_1

> 98,5

SDCCH real blocking

Blck_5a

< 1.0

TCH call blocking, before DR

Blck_8i

< 2.0

TCH drop call(dropped conversation) %

Dcr_5a

< 2.0

Total handover failure ratio

Hfr_2a

< 10,0

In case any of the KPI degradation, investigations should be started to see if the history of the cell performance was fine. In case performance degeneration is not caused by hardware or parameter problems, but by the network plan, the cell in question is transferred to post-swap optimization process. During the swap close KPI monitoring is needed with daily or hourly statistics, depending on the schedule and agreement with the customer. Immediately after swap following Reporting Suite reports should be checked for all new cells for any unexpected performance changes or degradation. The reports and details can be found from reference 11. For 2G: • RS_001: 2G System program • RS_ 063: parameter audit – to ensure that database is downloaded to the network correctly • RS_153: handover adjacent cell stats – to check that Handovers are occurring to the defined neighbors • RS_211/216/213: BTS/Cell doctor, in case of expected problems – Cell Specific • RS_206/209 For 3G: • RSRAN000: System Program • RSRAN073: Service/Session Accessibility Analysis • RSRAN079: Service/Session Retainability Analysis • RSRAN028: Soft Handover Performance • RSRAN046: SHO Adjacencies • RSRAN045: ISHO Adjacencies • RSRAN092: HSPA Overview

Page 27 of 49

1.26.2 Neighbour relations

Handover performance -

If any degradation is observed in handover performance (intra- of inter-system), following Reporting Suite reports will help to identify if there is a certain adjacencies causing the problem. For 2G: • RS_153: Adjacencies having high HO failure ratio • RS_154: HO attempt case distribution by cells For 3G: • RSRAN044: IFHO Adjacencies • RSRAN045: ISHO Adjacencies • RSRAN046: SHO Adjacencies To improve HO performance of the cells first the neighbours should be reviewed for any neighbour parameter mismatches. The best way for finding missing neighbours is to analyze the drive test logs. If detected set reporting feature is enabled in 3G, missing neighbours can also be found from OSS statistics.

1.27

Post-swap network verification (drive test)

A second Radio Network Verification will be carried out after the swap has been completed, i.e. at a time, when the network is operational. Aim to carrying out the second set of drive tests under similar traffic conditions as before, route, weekday and time of the day for the tests should be similar to those of the first verification. Measurements and KPI results for both of the drive tests will be compared and evaluated in details.

BSS specific considerations for swap 1.28

Multilayer network

If the network to be swapped is dual band, from the OSS dump the dual band strategy can be found or alternatively discussing with the customer. Based on the strategy the parameters can be modified. In NSN dual band strategy, (traffic reason or Umbrella) HO feature is used to push the traffic between 900 & 1800 layers as well as between Macro and Micro cells. The feature with the recommended settings is discussed next.

Page 28 of 49

1.29

Combined Handovers

Figure 12 Principle of multilayer network and different handover between layers

The handover to the upper layer will be triggered by a standard Rx Level Ho (Either DL or UL). That means as soon as the level of the lower layer gets below the defined minimum (for e.g. -90 /-87 dBm) a handover to the upper layer will take place. In parallel a quality handover (due to bad quality or interference) to the upper layer will be possible as well. Between the cells of the same layer a power budget, level or quality handover is possible. Counter for each adjacent 1800/micro cell 900 / Macro cell’s parameters

+2

measurement above rxLevMinCell

for each adjacent micro cell:

-1

otherwise

• fastMovingThreshold • rxLevMinCell • hoLevelUmbrella

=

10

=

= -102 dBm

Fast Moving Threshold ( For ex : 10 )

= - 75 dBm HO based on “HO Umbrella Level” allowed

Figure 13 Example of multilayer network parameterization

Multi-layer Handovers & Parameters

Page 29 of 49

Figure 14 Example of multilayer network parameterization

1.30

2G parameter cross-checks before swap

Following cross-checks are recommended before the actual swap to make sure correct planned parameters are implemented to the network. 

Reporting Suite: Default parameter audit report (063) (all cells)



Cross-checks



-

SDCCH configuration (some small and large configuration cells)

-

The default SDCCH configurations

-

CI/ BCC/NCC/LAC (check if new NCC/LAC is used)

-

Number of TRX's & respective Frequencies

-

HO definitions and settings:

-

Outgoing relation on new cells

-

Incinomg relations on new cells (same OSS)

-

Incoming relations on new cells (from other OSS's : other vendor)

Inputs -

Daily Swap plan

Page 30 of 49



-

Parameter Dump

-

RS_211 Report (Reporting Suite)

Outputs -

1.31

NetAct Plan Editor export file incase of parameter modification

Setup OSS performance monitoring

For performance monitoring different measurements should be set-up in OSS in an optimized way such that OSS load remains under control. The standard measurements to be set-up in OSS are as follows.

1.31.1

Standard 2G measurements

Following are the standard measurements that should be enabled in the BSC during swap for performance monitoring. Measurement time is depending on the load of BSC, it is recommended to collect as much as possible without any risk of BSC overload.

NSN Measurement Set 1 Item

Time (AVP)

1.1 1.2 1.3 1.4 1.5

1 hour 1 hour 1 hour 1 hour 2 hours

1.6 1.7

1 hour 3 hours

1.8

When

Activity, name

Type

OSS table

Each day:

_traf _resavail _resacc _ho _powerctrl

Traffic Resource Availability Resource Access Handover Power Control

p_nbsc_traffic p_nbsc_res_avail p_nbsc_res_access p_nbsc_ho p_nbsc_power

Each day:

_ClearCode _undefadjcell

BSC Clear Code Undefined Adjacent

p_nbsc_service p_nbsc_undef_adj_cell

2 hours

21:30-00:00 Each day:

_AdjCell

Cell Handover Adjacent Cell

p_nbsc_ho_adj

1.9

1 hour

8:00-10:00 & 21:00-23:00 Mon-Sun:

_RxLev

RxLev

p_nbsc_rx_statistics

1.10

1 hour

08:00-09:00 & 21:00-22:00 Mon-Sun:

_LinkBal

Link Balance

p_nbsc_link_balance

1.12

1 hour

08:00-09:00 & 21:00-22:00 Mon-Sun:

_TimingAdv

Timing Advance

p_nbsc_timing_advance

8:00-10:00 &21:00-23:00

08:00-09:00 & 21:00-22:00

The measurements with an averaging period (AVP) of 1 hour are running every day from 00:00 until 24:00 except else is specified.

1.31.2

Other 2G measurements

Page 31 of 49

Some other types of measurements are available. These will mainly be used for trouble shooting purposes and analysis of problems occurred during SWAP. They will be programmed by OSS on demand of the NSN optimization group in order to check the infected network elements. The number of extra measurements will be kept minimal: 20 measurements, in order not to overload the OSS. Other raw measurements.

2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9

Name

Type

OSS-table

_load _avail _OSI1 _OSI2 _OSI3 _OSI4 _cc _ccpm _trx_avail

Load Availability OSI level 1 OSI level 2 OSI level 3 OSI level 4 BSC Clear Code Measurements BSC Clear Code Measurements PM Resource availability per BSC

P_nbsc_load P_nbsc_avail P_nbsc_osi1 P_nbsc_osi2 P_nbsc_osi3 P_nbsc_osi4 P_nbsc_cc P_nbsc_cc_pm P_nbsc_trx_avail

RAN specific considerations for swap If the swap is between two vendors the soft handovers between different vendors can be problematic. When cells are having same carrier frequency and soft handover is not possible there is a high risk of increased interference and call drops at the cell borders. In such case it is highly recommended that during the swap there would be a separate carrier for new cells. If it is not possible to use other carrier frequency during the swap it should be taken care that cells are swapped in such clusters that there will not be inter-vendor cell borders in critical locations. If swapped cells are allocated with a different carrier frequency, inter-frequency handovers (IFHO) have to be enabled with suitable parameters at both vendor’s network to allow full mobility. If IFHO is not possible, ISHO (handover to GSM) can be used to prevent call drop at inter-vendor coverage border. These options are presented in a diagram in Figure 15. In network modernization case there should be no problems with SHO.

Page 32 of 49

Figure 15. Flow diagram for deciding inter-vendor handover strategy during swap.

Multivendor parameter and KPI/counter mapping In a swap project where other vendor is replaced with NSN equipment mapping for network configuration parameters and OSS performance monitoring KPIs will be needed. Usually target is to have one-to-one swap with same features and parameters before and after swap. New features are then enabled after swap is completed and acceptance KPIs are met. Fully similar mapping is usually not possible due to implementation and parameter differences between the vendors. Therefore target is to have as close mapping as possible. It should be discussed with the customer that there may be some differences in some of the functionality. Also available counters and their pegging to network events differ between different vendors. This causes some uncertainty to the OSS statistics when counter based performance delta between old and new network is measured. Due to the counter differences it is recommended to use only some high level KPIs such as setup success rates and drop rates from OSS as acceptance KPIs, since they are usually quite well defined in all vendors’ networks implementation. More detailed and specific KPIs may not measure exactly same events and they difference in the KPI values may wrongly be thought to be due to the network performance. To overcome the uncertainties in OSS bases KPIs in a vendor swap, drive test KPIs should always be collected and they should have the heaviest weight in the new network performance evaluation and comparison to the earlier performance.

Page 33 of 49

References to available KPI and parameter mapping between NSN and other vendors are collected to the following paragraphs.

1.32

BSS KPI and parameter mapping references

All multivendor related mapping references are collected to Multivendor folder in IMS-sharenet: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/410911135 NPO CaMgmt GERAN Modernization folder is located to https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/403811279 Ericsson to NSN BSS KPI and parameter mapping tables can be found from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D431032683 https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D427793484 Huawei to NSN BSS KPI and parameter mapping tables can be found from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D426649378 https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D429739169 For other vendor mappings please see Multivendor folder in IMS and references to past projects in Chapter .

1.33

RAN KPI and parameter mapping references

All multivendor related mapping references are collected to Multivendor folder in IMS-sharenet: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/410911135 NPO CaMgmt WCDMA Modernization folder is located to https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/400096872 Ericsson to NSN RAN KPI mapping tables can be found from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D425759283 Huawei to NSN RAN KPI and parameter mapping tables can be found from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D425332910

Page 34 of 49

https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D426651601 For other vendor mappings please see Multivendor folder in IMS and references to past projects in Chapter .

1.34

NSN default parameters

NSN BSS parameter dictionary with default parameters can be found from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D428454034 NSN RAN parameter dictionary with default parameters can be found from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D419165584 and NPO recommended parameters for RAN optimization from https://sharenetims.inside.nokiasolutionsandnetworks.com/livelink/livelink/overview/D419150667 NSN counter and parameter definitions are also included in the BSS/RAN Operation documents available from NOLS in pdf or NED format, see references 1 and 2. All network parameters with default values in Excel or other formats can also be downloaded from PDDB http://pddb.inside.nokiasolutionsandnetworks.com/pddb/login.do

Reference material from past projects Swap support folder https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/382179624 contains links to nearly all IMS material related to network modernization and swaps. General IMS folder for swap and modernization lessons learnt documents https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/382928792 Pre-sales information for several swap and modernization cases can be found from https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/369416358 Links to project material and lessons learnt slides of some past projects are in following chapters.

Page 35 of 49

1.35

BSS swap projects

Ericsson to NSN swaps: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/412585060 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/412571763 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D419716426 ALU to NSN swap: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D358950572 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D372590825 Nortel to NSN swaps: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/428093661 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/428068933 Motorola to NSN swaps: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D412551394 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D419697334 Ex-Siemens to NSN modernizations: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D427716508 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D420125396 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Overview/D383496707 For GEMINI project references, see https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/417140320

1.36

RAN swap projects

NEC to NSN swap: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/414789669 ALU to NSN swap: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/397985561

Page 36 of 49

References 1. NOLS / WCDMA RAN Operation document https://online.portal.nokiasolutionsandnetworks.com/pic/com/nsn/extranet/pic/controller/productin foview/pivdocumentation.do?productId=urn:nsn.com:mxpdm:133-001958 2. NOLS / GSM/EDGE BSS Operation document https://online.portal.nokiasolutionsandnetworks.com/pic/com/nsn/extranet/pic/controller/productinfoview/pi vdocumentation.do?productId=urn:nsn.com:mxpdm:133-001870 3. UTRAN and GERAN Parameter assessment and consistency check WI https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/D364148491 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/380101296 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/400432089 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/377623846 4. NetAct Plan Editor https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/390002169 5. UTRAN neighbour planning WI https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/393715157 6. UTRAN Neighbour assessment WI https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Download/380115223 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/397937092 7. Geran frequency and neighbour planning WI https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/392365775 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/394291362 8. UTRAN and GERAN Cluster tuning & acceptance guideline https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/D368977093 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/396547922 9. UTRAN and GERAN Performance analysis WI https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/374963768 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/390757710 https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/398160832

Page 37 of 49

10. Jump portal http://nop-i.nokiasolutionsandnetworks.com 11. Reporting suite reports http://nop-i.nokiasolutionsandnetworks.com/reportmanager/htmlset.php?set=437&co=1&m=1&se=1 http://nop-i.nokiasolutionsandnetworks.com/reportmanager/htmlset.php?set=503&co=1&m=1&se=1

Page 38 of 49

Appendices Appendix A – Templates for Technical Site Survey Summary (TSSR) and site verification drive test

TSSR Template

Drive Test Template

Page 39 of 49

Appendix B – Example of a master plan for 2G and 3G Table 1, Master plan database fields (2G)

Page 40 of 49

Database Field

Description

BSC_Name BSC_id Site_id

Unique key for collocated 900 and 1800 sectors on the same site or for all sectors on the same site

BCF_Name BCF_id BTS_Name BTS_id

BTS_id that will be generated during the creation

Direction

Antenna Direction

Direction_Adj

Antenna direction used in the NETACT adjacency tool

Sector

Sector number

System

GSM900 or GSM1800

Status

Is BTS on air

Max_Config

Maximum of TRXs in the actual sector

TRX_onair

The number of TRX on air in the integration

TRX_installed

Number of TRX's installed

Config

e.g. 3+4+2

On_air

Is sector on air or not

Planned_SWAP Date Actual_SWAP Date SWAPped

YES / NO

Foreigns_removed

YES /NO

CI

Cell ID

BCCHtype

MBCCH/MBCCHC/MBCCB

SDCCH

Number of full SDCCH timeslots

LAC_old

Old vendor network LAC_id

LAC_new

New LAC_id

NCC_old

Old vendor network NCC

NCC_new

New NCC (used temporary during the SWAP)

BCC

Same BCC as old vendor network

BCCH

BCCH frequency

Hopping

Hopping ON, OFF

HSN

Hopping sequence number

HYS

Cell re-selection hysterisis

REO

Cell re-selection offset

Page 41 of 49

Page 42 of 49

Table 2, Master plan database fields (3G) Database Field Site Name WBTS id Old RNC id New RNC id WCEL id TRS IP address Subnet Mask BTS IP address RNC IP address HSPA

External equipment IP addresses Transmission type Transmission setting parameters Carriers in use Config On_air Planned_swap Date Actual_swap Date swapped Foreigns_removed RF-Parameters … TRS-Parameters …

Description Site Name (old and new are same) Old system RNC id (and name if needed) New system RNC id (and name if needed)

Enable /Disable Columns for IP-addresses of remote electrical tilt, battery backup unit, location measurement unit, etc… Number of E1s or other specifiications Columns as needed

Live status Date Date when confirmed Yes/No, status changed after succesful swap Yes/No, status changed after database deletions Tx powers, handover parameter sets, etc...

Other Cell-, WBTS-, and Site-specific parameters as needed …

…

Page 43 of 49

Appendix C – Standard configurations for a 2G swap Introduction Following is a brief description explaining the standard antenna and TRX configurations that can be used during the customer's network swap with Flexi EDGE BTS.

Purpose The purpose of this document is to explain the possible configurations for the antenna line if the existing site configuration involves Radio Tunable Combiners (RTC) that can combine up to 5 TRXs. Changing from RTC to WBC combiners (2-way) can lead to different antenna and feeders requirements. The following are standard configurations, which will help in the assessment of additional feeders and cables.

Standard Flexi EDGE BTS configurations For more information about Flexi EDGE BTS and configurations, please see link to Flexi BTS documentation: https://sharenet-ims.inside.nokiasolutionsandnetworks.com/Open/375107768

Combining By-pass, 2way RX diversity, 2TRX /Cell

Flexi EDGE BTS configuration

Page 44 of 49

2-way wideband combining, 2-way RX diversity, 4TRX/cell

Flexi EDGE BTS configuration

4-way wideband combining, 2-way RX diversity, 8TRX/cell

Flexi EDGE BTS configuration

Page 45 of 49

Examples of antenna configuration conversions for SWAP: CASE I: Three Vertical Polar antennas in sector and 4 or less TRXs Existing : Before SWAP

Antenna configuration before swap

After : SWAP

Antenna configuration after swap Note : Disconnect the TX antenna for the SWAP to NSN

Page 46 of 49

CASE II: Three vertical pole antennas and more than 6 TRXs in the sector Existing : Before SWAP

Antenna configuration before swap

After : SWAP Replace the three vertical pole antennas with two cross-polar antennas about 1m apart.

Antenna configuration after swap Note : In case of Urban environment, the two X-Polar antennas need only be 1m apart.

Page 47 of 49

CASE III: Five or more TRXs in the sector and one cross-polar antenna Existing : Before SWAP

Antenna configuration before swap

After : SWAP to NSN

Antenna configuration after swap Note :  If the SWAP NSN configuration is 5/6 TRXS three feeders are required per sector.  If the SWAP NSN configuration is 7/8 TRXs four feeders are required per sector.  The existing cross-polar will be taken out and replaced by two new X-Polar Antennas

Page 48 of 49

CASE IV: More than four TRXs for G900 or more than four TRXs for 1800 and one dual band cross polar antenna per sector. Existing : Before SWAP

Antenna configuration before swap

After : SWAP to NSN

Antenna configuration after swap

Note : 

This configuration is good for up to 8 TRXs for G900 and G1800 per sector.



Existing dual band antenna will be taken out and replaced by two new Kathrein dual band antennas.

Page 49 of 49

Appendix D – Antenna conversion If the customer is using different types of antennas in there network e.g. Algon, Celwave, ADC., NSN is proposing to use only Kathrein antennas for SWAP, expansion and new sites. Attached is a file where some other antenna types are related to their Kathrein equivalent antennas. This correlation of antennas is based on the general antenna characteristics e.g. gain, horizontal and vertical beam width, and polarization. Only some 900 and 1800 MHz band antennas are included in the list.

Antenna_Specs