Commissioning of AN5116-06A Data Service (OLT)
Agenda • Preparation before configuration • Commissio Commissioning ning of data service
• VLAN configuration of OLT • Configuration of ONU port
• OLT QINQ domain function • OLT QINQ domain configuration
• OLT QINQ domain command line • Note
• FAQ
reparation Before Configuration 1. Configure management VLAN ANM2000 EMS works on the equipment only after management VLAN and IP configured
Connect the Console port
Configure management VLAN and IP
reparation Before Configuration Connect
the Console port
Use Hyper Terminal software: Enter 【Startup】→【Program】→ 【Accessary】 →【Communications】→【Hyper Terminal】 Connect serial port of PC and CONSOLE port of AN5116-06A with a serial-port cable.
reparation Before Configuration
Before the user enters the console, the system will check his identity.
The user should input right username and password. Configuring management VLAN requires the user to be in configuration mode. The default name and password of an administrator are GEPON, GEPON and EN, GEPON respectively.
reparation Before Configuration Configure management VLAN Type “cd service” after command prompt Admin# in configuration mode to get into directory of commands for VLAN management. To configure configur e management VLAN, use the following command: set manage vlan name
vid inputport [untagged|tagged] : VLAN ID ID of management VLAN, ranging between between 1 and 4085. : Port of the management VLAN. [untagged|tagged]: Specify port of this management VLAN is in Untagged mode or Tagged mode.
Example: set manage vlan name test vid 1000 inputport 19:4 untagged
reparation Before Configuration Configure management IP
set manage vlan name ip {}*1 : IP address of management VLAN, of it M referring to subnet mask bits. {}*1: Equipment gateway gat eway,, optional (The setting of gateway is necessary only when equipment and EMS fall within different net sections) Example: set manage vlan name test IP 10.18.250.3/16
reparation Before Configuration 2. ANM2000 Basic Configuration
Flow Chart
Log in ANM2000 and start basic system configuration
Enter Edit Mode Add Domain
Add System
Save and Enter Edit Mode Again
Add a Module
Detect Physical Configuration
Set Card Authorization
Time Calibration
End
Set SNMP Trap Receiver IP and Time Management
reparation Before Configuration Add Domain Right-click the blank at the Logical Tree tab in the browse tree pane, and then select Add Domain… in the shortcut menu to enter the Add Domain dialog box
reparation Before Configuration Add System
Management IP of equipment
reparation Before Configuration Add a Module Right click added system in the logical tree tab to show its context menu.
Click “Add Module” in the menu and a dialog box “Add Module” will pop up.
NOTE: Click “Save” button in the toolbar to save above configuration into the the database and enter Edit Mode again.
reparation Before Configuration Detect Physical Configuration
reparation Before Configuration Set Card Authorization
reparation Before Configuration Set SNMP Trap Receiver IP
IP address of EMS
Equipment uses trap receiver IP to report alarms to EMS
reparation Before Configuration Set Time Management
IP address of EMS
Set time management for time calibration
reparation Before Configuration Time Calibration Function of time calibration is to t o keep time of EMS server in agreement with that of the equipment
Commissioning of Data Service •
Preparation before commissioning ： Check whether the status indicator is ready; check ONU is registered or not.
•
ONU authentication. ONU is authenticated using MAC address whitelist.
•
Configuration of OLT VLAN. According to OLT OLT VLAN requirement, requirement, choose proper port and configure the VLAN table for OLT.
•
Configure ONU port parameters.
•
By clic clickin king g “FE “FE port port conf config igur urat atio ion” n”,, conf config igur ure e the the ONU ONU VLA VLAN N mode mode..
•
Configuration of OLT SVLAN. According to ONU configuration and OLT OLT requirement, requirement, configure the VLAN profile of OLT QINQ domain.
•
ONU binding：
Commissioning of Data Service •
Check the power supply (-48v DC:-40V~-57V), make a data service plan before powering on the system.
•
Make plans for data service, record ONU MAC address and authentication ID.
•
Make sure the power supply keep accordance with the requirement of equipment, make sure the voltage within standard range.
•
Check the status indicator of cards c ards Card works properly when ACT indicator of HSWA card, EC4B card, uplink card is on. Communication between ONU and EC4B has been established successfully succ essfully when LINK indicator of EC4B card is on.
•
Check the type of ONU Check the software version of cards Check the connection status of system. Check the connection between PON port and ONU. Check the connection of uplink cards. Check the connection between EMS and HSWA by serial port.
ONU Authentication (1) •Choose “config”, then “ONU authentication” -> “ONU physic_IDaddress physic_IDad dress Whitelist”
ONU Authentication (2) •
Click “Get Unauthorized ONU”.
ONU authentication (3) •
Choose Choo se cor corre resp spon ondi ding ng Slot Slot No No.. and and PON PON No. No., clic click k “Ge “Gett Unauthorized ONU”.
ONU authentication (4) •
Choose Choo se the these se O ONU NUs s and and cli click ck “OK “OK””. Then Then cli click ck “W “Wri rite te Device”,, after that ONU Authorized No. will be offered Device” automatically by system.
VLAN Configuration of OLT • Configuration interface 【HSWA】→ 【Config】 → 【Local
VLAN】
• Function Configure the parameters of interface on local end, including service name, type, interface No. and VLAN range, etc.
OLT VLAN Configuration
• Parameters introduction Service
name Customer can define a specific service name for convenience. Starting VLAN ID Start value of VID range:1-4085 VLAN ID end End value of VID range:1-4 range:1-4085 085 Interface ID (Uplink port ID or TRUNK ID) XFP:10G optical port SFP：1G optical port GE：10/100/1000M electric port Tag/Untag mode Define VLAN is tagged or untagged Service type Pre-define the type of service
ONU Port Configuration
• Function Configure
the data service of ONU side, such as CVLAN, SVLAN, etc.
• Configuration • Pleas Please e refer refer to “Com “Commis missio sionin ning g of AN511 AN5116 606A Data Service (ONU).PPT”
OLT QINQ Domain Function
• Function introduction
Multiple functions for VLAN tag, VLAN translation and VLAN add of upstream direction. Corresponding operation of VLAN for downstream direction can be executed, according to that of the upstream direction. Configuration for upstream and downstream data is enabled, based on which optional operation can be done according to pre-defined parameters. Operation for VLAN based on PON port and ONU is supported. COS remarking is supported.
OLT QINQ Domain Configuration •QINQ domain configuration interface 【HSWA】→ 【Config】 → 【QINQ】→
【OL OLT T QINQ Domain 】
1. Each domain has a certain name. 2. VLAN of four layers can be configured in each domain. But only the first two layers’ operation are supported currently. 3. Maximum 32 services can be configured in a single domain. 4. Maximum 1024 domain configuration can be supported currently.
OLT QINQ Domain Configuration •QINQ domain parameter introduction •Parameters
Serial
No.
Service
Maximum 32
type
Reserved for future use
Up/down
clause Define the feature of up/downstream packets layers’ VLAN domain ：Each layer’s VLAN can be configured according to customer’s requirement, of which only the first two layers’ are supported support ed currently. currently. Four
•
VLAN layer introduction ：
First layer VLAN– VLAN–It can be a CVLAN when upstream data from ONU with one layer’s VLAN, it can be a inner CLVAN when upstream data from ONU has two layers’ VLAN.
Second layer VLAN
It’s outer VLAN, namely SVLAN
OLT QINQ Domain Configuration •QINQ domain configuration interface •Each layer’s VLAN parameter
Nth layer’s VLAN of customer：Original VLAN of upstream direction from ONU. Nth layer’s VLAN COS：COS ID of Nth layer’s VLAN. Action：Action can be executed for Nth layer’s VLAN, including “add” and “transparent”.. “transparent” Tag identification：New TPID of Nth layer’s VLAN after the action. Priority：COS value of new VLAN after the action. New VID：VID of new VLAN after the action.
OLT QINQ Domain Configuration •PON attach interface 【EC4B】→ 【Config】 → 【PON
Attach/Detach Domain】
•
Binding for each PON port is enabled.
•
Each PON port can be bound to multiple domains.
•
Multi-cards can share one domain.
•
Domain should be either bound to OUN or PON port.
OLT QINQ Domain Configuration •ONU attach interface 【04ONU】→ 【Config】 → 【ONU
Attach/Detach Domain】
•
Multiple domains can be used for binding one ONU.
•
Binding of domain for multi-ONUs and multi-PON ports is enabled.
•
Note：The domain can’t be used for binding PON port of the line card if it has been bound for ONU under this line card.
OLT QINQ Domain Configuration Example Example 1: Use QINQ QINQ Domain to create CVLAN=100, SVLAN=1000 SVLAN=1000 Bind QINQ Domain to PON Port
OLT QINQ Domain Configuration Example Click
to add one Domain
OLT QINQ Domain Configuration Example Click
again in the right window to add one row
OLT QINQ Domain Configuration Example Set Up Clause: VLAN1(CVLAN)=100
OLT QINQ Domain Configuration Example Set Down Clause: VLAN2(SVLAN)=1000
OLT QINQ Domain Configuration Example Configure 1st Layer’s Parameters Set Old_CVLAN Low=100
OLT QINQ Domain Configuration Example Set Action: Transparent
OLT QINQ Domain Configuration Example Configure 2nd Layer’s Parameters Set Action: Add
OLT QINQ Domain Configuration Example Set New VID(SVLAN)=1000
OLT QINQ Domain Configuration Example Bind QINQ Domain to PON Port
OLT QINQ Domain Configuration Example Bind QINQ Domain to PON Port
OLT QINQ Domain Configuration Example Example 2: 2: Use QINQ Domain to create create 100 100≤ ≤CVLAN CVLAN≤ ≤200, SVLAN=1000 Bind QINQ Domain to PON Port
OLT QINQ Domain Configuration Example Click
to add one Domain
OLT QINQ Domain Configuration Example Click
again in the right window to add one row
OLT QINQ Domain Configuration Example Set Up Clause: 100 100≤ ≤VLAN1(CVLAN) VLAN1(CVLAN)≤ ≤200
OLT QINQ Domain Configuration Example Set Down Clause: VLAN2(SVLAN)=1000
OLT QINQ Domain Configuration Example Configure 1st Layer’s Parameters Set Old_CVLAN Low= blank
OLT QINQ Domain Configuration Example Set Action: Transparent
OLT QINQ Domain Configuration Example Configure 2nd Layer’s Parameters Set Action: Add
OLT QINQ Domain Configuration Example Set New VID(SVLAN)=1000
OLT QINQ Domain Configuration Example Bind QINQ Domain to PON Port
OLT QINQ Domain Configuration Example Bind QINQ Domain to PON Port
Note:
•
Maximum services of QINQ domain profiles should be less than 22 at each PON port.
•
N:1 transform can only be realized by attaching profile to ONU. PON port does not support N:1 transform unless through other indicators such as COS.
•
OLT QINQ domain requires that VLAN can be processed by downstream data only after MAC address has been learned by upstream data
•
Instead of supporting broadcast packets from downstream direction, OLT QINQ domain transmit the packets transparently to the users without processing VLAN.
FAQ •
Service Failure (FTTH ONU)
Check VLAN configuration of OLT and the correctness of SVLAN.
Check the correctness of QINQ domain profile parameters of OL OLT T and VLAN information.
Verify whether VLAN operation is effective by checking MAC address Verify table of equipment.
Check where service failure occurs by CLI
Thank You! FiberHome Technologies
