Management Case Study on Toyota Motors.Full description
Toyota case study solution
Case studyFull description
Case study, week 3,Full description
Case Study Toyotoa
engineering managementFull description
Case Study Toyota in China
ALOU Second Assignment
Full description
Case Study Financial ManagementFull description
PP 604 - International Management Case Study Q & AFull description
Study notes for MBA students, Cost and Quality Management.Full description
A Case Study of Quality Management on Rolls Royce
Assignment # 3 Eslsca 2017Full description
Case study answers on Operations Management by StevensonFull description
05 Intro ERP Using GBI Case Study MM[A4] en v2.01
Answers to the case questions Name: 吳菲樂 105363127 Case name: Quality Management !oyota !oyota Question 1: "# the s$eci#ication is such that no washer shoul% &e greater than 2'( milimeters) assuming that the thic*nesses are %istri&ute% normally) what #raction o# the out$ut is e+$ecte% to &e greater than this thic*ness, Answer: !he -raction that is e+$ecte% to &e greater than this thic*ness is 1,844098808. Question 2: "# there are an u$$er an% lower s$eci#ication) where the u$$er limit is 2'( an% the lower lower limit is 1'() what #raction o# the out$ut is e+$ecte% to &e out o# the $rocess, Answer: !he #raction to &e e+$ecte% to &e out o# the $rocess is 2,208517% Question 3: /hat is the C pk #or the $rocess , Answer: !he C pk #or the $rocess is 0,695689. Question (: /hat woul% &e the C pk #or the $rocess i# it were centere% &etween the s$eci#ication limits assume the $rocess stan%ar% %eiation is the same, Answer: !he the C pk #or the $rocess i# it were centere% &etween the s$eci#ication limits woul% &e 0,795073574. Question 5: /hat $ercentage o# out$ut woul% &e e+$ecte% to &e out o# tolerance i# the $rocess were centere%, Answer: !he $ercentage o# out$ut to &e e+$ecte% to &e out o# tolerance i# the $rocess were centere% is 1,706888% Question 6: et u$ X an% range control charts #or the current $rocess' Assume the o$erators will ta*e sam$les 10 washers at a time' Answer: ´
A2 =0.31 D3 =0.22 D4 =1.78 Lower limit X 41'761 Upper limit X 42'16( Lower limit R= 0.143 Upper limit R=1.157 Question 7: lot the %ata on your control charts' oes the current $rocess a$$ear to &e in control, Answer: ´
´
control c!rt "#$!r LL &"#$!r'#$!r UL
control c!rt
R LL R#$!r UL
Accor%ing to the control charts a&oe) the $rocess seems to &e in control) as the %ata is still con#ine% &etween the u$$er an% lower limits Question : "# the $rocess coul% &e im$roe% so that the stan%ar% %eiation were a&out only '10 milimeter) what woul% &e the &est that coul% &e e+$ecte% with the $rocesses relatie to #raction %e#ectie, Answer: "# the $rocess coul% &e im$roe% so that the stan%ar% %eiation were a&out only '10 milimeter) then %e &est that coul% &e e+$ecte% with the $rocesses relatie to #raction %e#ectie woul% &e 573 %e#ects in eery 1 &illion washers'