La maggior parte - e non - dei comandi usati da terminale. La memorizzazione di tali comandi e la loro comprensione implica una preparazione di un certo livello...Full description
Full description
Descripción: It is a Dokument about Fortigate OS Command Line Interface
Command Line Interface for Datastage
Using the VPN Client Command-Line InterfaceFull description
Plant Design Management System Advanced Command Line Syntax, Synonyms & Construct SyntaxFull description
Plant Design Management System Advanced Command Line Syntax, Synonyms & Construct SyntaxFull description
LAUNCHING CLI INTERFACE ........................................ERROR! BOOKMARK NOT DEFINED.
IP-10 Quick Startup Guide
2
Doc Rev0.1
PROPRIETARY
Document Purpose
1.
The purpose of this document is to describe the basic configuration steps of IP-10 through the CLI interface radio link.
2.
Document Scope
This document describes the recommended initial steps in order to connect and manage IP-10 radio link through the CLI Interface. It includes the t he configuration steps of the following main sections:
3.
•
Connecting to IDU using default factory setup
•
Launching the hyper terminal
•
SW Upgrade
•
License key activation
•
Basic parameters configuration
Startup Configuration Steps
Basic configuration includes the following basic steps: 1. Complete physical physical HW installation of IDU, IF coax cable, RFU and and antenna as per installation instructions. 2. Connect PC to IDU and and Launch the Hyper Hyper terminal. 3. Upgrade IDU SW. 4. Load license key. 5. Configure radio link parameters. 6. Complete link commissioning.
IP-10 Quick Startup Guide
3
Doc Rev0.1
PROPRIETARY
Getting Started To log in to the CLI: 1. Power on your PC. 2. Make sure that your PC is connected to the management port on the front panel of the IP-10 unit. 3. For a first-time login, use the following: User: admin Password: admin Note: When using the Hyper Terminal, you should set the terminal speed (in your PC terminal Configuration) to 115200 kpbs. In addition, it is recommended to select the VT-100 terminal type and set the Terminal size to 24 rows, 80 columns.
SOME COMMAN COMMAND
IP-10:/> Name -Info -------------------------------------------------------------------------------ls list entities get get parameter set set parameter help help cd change directory exit exit CLI logout logout from CLI cli-ver cli version cls clear screen shell enter secondary shell write Write the current switch configuration into configuration file show-tree Show entity tree find Search for a string in the parameter's entity name and information fields lsp list entity parameters and commands
IP-10 Quick Startup Guide
4
Doc Rev0.1
PROPRIETARY
MAIN MANU IP-10:/> ls management - Management platform - Platform radio - Radio interfaces - Interfaces diagnostics - Diagnostics xml-interface - XML Interface
Management Command Line 1. Check the IP Address IP-10:/> get management/networking/ip-address/ip-address↵ 192.168.1.10
2. Change the IP Address IP-10:/> set management/networking/ip-add management/networking/ip-address/ip-address ress/ip-address 192.168.1.20 ↵ You may lose remote management connection to the unit if this value is changed i icorrectly. Are you sure? (Yes/no):yes ↵
3. Check Subnet Mask IP-10:/> get management/networking/ip-address/subnet-mask ↵ 255.255.255.0 4. Change Subnet Mask IP-10 :/> set management/networking/ip-add management/networking/ip-address/subnet-mask ress/subnet-mask 255.255.255.0↵
7.Check HW Address IP-10:/> get management/networking/ip-ad management/networking/ip-address/hw-addre dress/hw-address ss ↵ 00:0A:25:00:19:23 8.Check management port IP-10:/> get management/networking/numb management/networking/number-of-ports er-of-ports↵ 3 9. Create Management Port IP-10:/> set management/networking/numbe management/networking/number-of-ports r-of-ports 2 ↵
10. Check Vlan ID IP-10:/> get management/networking/vlan management/networking/vlan↵ 1 11. Create Vlan IP IP-10:/> set management/networking/vlan management/networking/vlan 2↵ 12. Check Management Type IP-10:/> get management/networking/type management/networking/type↵ in-band 13. Change Management Type IP-10:/> set management/networking/type management/networking/type out-of-band IP-10:/> set management/networking/type management/networking/type in-band 14. Check Management Capicity IP-10:/> get management/networking/capacity management/networking/capacity 2mbps
IP-10 Quick Startup Guide
6
Doc Rev0.1
PROPRIETARY
19. Set to Default Configuration IP-10:/> /management/mng-services/cfg-service/set-to /management/mng-services/cfg-service/set-to-default -default You are about to set the unit configuration to its default values. This operation will take effect only after a unit reset. Are you sure? (yes/no):no
22. Showing current Alarm IP-10:/> /management/mng-services/alarm/management/mng-services/alarm-service/alarm-curre service/alarm-current/show nt/show Date&Time
Severity AlarmName
Origin
Text
IP-10:/> get /management/mng-services/alarm/management/mng-services/alarm-service/alarm-curre service/alarm-current/most-severe nt/most-severe cleared 25. Check and update Date and Time IP-10:/> get management/mng-services/time-serv management/mng-services/time-service/time-and-date ice/time-and-date 27-11-2008,11:42:38 IP-10:/> set management/mng-services/time-service management/mng-services/time-service/time-and-date /time-and-date 27-112008,11:50:01
33.Protection Enable Disable IP-10:/> get platform/mate-idu/protection-admin platform/mate-idu/protection-admin disable IP-10:/> set set platform/mate-idu/protection-admin platform/mate-idu/protection-admin disable enable IP-10:/> set platform/mate-idu/protection-admin platform/mate-idu/protection-admin enable
IP-10 Quick Startup Guide
7
Doc Rev0.1
PROPRIETARY
35. Set TX/RX Frequency IP-10:/> get radio/rfu/tx-freq 14515000 IP-10:/> set radio/rfu/tx-freq 14515000 IP-10:/> get radio/rfu/rx-freq 14935000 IP-10:/> set radio/rfu/rx-freq 14935000
36. Mute TX IP-10:/> get radio/rfu/mute-tx disable IP-10:/> set radio/rfu/mute-tx disable enable IP-10:/> set radio/rfu/mute-tx enable 37. Check TX/RX LEVEL IP-10:/> get radio/rfu/tx-level-status radio/rfu/tx-level-status 22 IP-10:/> get radio/rfu/rx-level -39
38. Check RFU Serial ,Part No and Software IP-10:/> get radio/rfu/serial-number radio/rfu/serial-number FC527553 IP-10:/> get radio/rfu/part-number radio/rfu/part-number IP-10:/> get radio/rfu/software-version-num radio/rfu/software-version-number ber C1.64_B5 39.RFU RF LooPBack IP-10:/> get radio/rfu/rfu-rf-loopback radio/rfu/rfu-rf-loopback↵ off IP-10:/> set radio/rfu/rfu-rf-loopback radio/rfu/rfu-rf-loopback off on IP-10:/> set radio/rfu/rfu-rf-loopback radio/rfu/rfu-rf-loopback on ↵ 40.RFU IF LoopBack IP-10 Quick Startup Guide
8
Doc Rev0.1
PROPRIETARY
IP-10:/> get radio/rfic/if-loopback radio/rfic/if-loopback↵ Off IP-10:/> set radio/rfic/if-loopback off on IP-10:/> set radio/rfic/if-loopback on↵
