ISO 128
1
ISO 128 ISO 128 is an international standard (ISO), about the general principles of presentation in technical drawings, more [1]
specific the graphical representation of objects on technical drawings.
Overview Since 2003 the ISO 128 standard contains twelve parts, which had been initiated between 1996 and 2003. It starts with a summary of the general rules for the execution of technical drawings, as well as presenting the structure. Further it describes basic conventions for lines, views, cuts and Sections, and different types of engineering drawings, such for mechanical engineering and construction in architectural, civil engineering, shipbuilding etc. It is applicable to both manual and computer-based drawings, but it is not applicable to three-dimensional CAD [1]
models.
The ISO 128 replaced the previous DIN 6 standard about drawings, projections and views, which was first published in 1922, and later updated in 1950 and 1968. The ISO 128 itself was first published published in 1982, contained 15 pages and "specified the general principles of presentation to be applied to technical drawings following the orthographic [2]
projection methods".
Several parts of this standard have been updated by individual parts and eventually the last
parts and the whole standard as a whole has been withdrawn by the ISO in 2001.
Composition of the ISO 128 The 12 parts of the ISO 128 standard are: • ISO 128128-1:2 1:2003 003.. Techni Technical cal draw drawing ingss —General principles of presentation —Part 1: Introduction and index • ISO 128128-20: 20:199 1996 6 Techni Technical cal draw drawing ingss — —General principles of presentation —Part 20: Basic conventions for lines
—General principles of presentation —Part 21: Preparation of lines by CAD • ISO 128128-21: 21:199 1997 7 Techni Technical cal draw drawing ingss — systems • ISO 128128-22: 22:199 1999 9 Techni Technical cal draw drawing ingss — —General principles of presentation —Part 22: Basic conventions and applications for leader lines and reference lines
—General principles of presentation —Part 23: Lines on construction • ISO 128128-23: 23:199 1999 9 Techni Technical cal draw drawing ingss — drawings
—General principles of presentation —Part 24: Lines on mechanical • ISO 128128-24: 24:199 1999 9 Techni Technical cal draw drawing ingss — engineering drawings • ISO 128128-25: 25:199 1999 9 Techni Technical cal draw drawing ingss — —General principles of presentation —Part 25: Lines on shipbuilding drawings • ISO 128128-30: 30:200 2001 1 Techni Technical cal draw drawing ingss — —General principles of presentation —Part 30: Basic conventions for views
—General principles of presentation —Part 34: Views on mechanical • ISO 128128-34: 34:200 2001 1 Techni Technical cal draw drawing ingss — engineering drawings • ISO 128128-40: 40:200 2001 1 Techni Technical cal draw drawing ingss — —General principles of presentation —Part 40: Basic conventions for cuts and sections
—General principles of presentation —Part 44: Sections on mechanical • ISO 128128-44: 44:200 2001 1 Techni Technical cal draw drawing ingss — engineering drawings
—General principles of presentation —Part 50: Basic conventions for • ISO 128128-50: 50:200 2001 1 Techni Technical cal draw drawing ingss — representing areas on cuts and sections • ISO/TS ISO/TS 128-71:2 128-71:2010 010 Techni Technical cal product product documentat documentation ion —General principles of presentation presentation —Part 71: Simplified representation representation for mechanical engineering drawings
ISO 128
2
Other ISO standard related to technical drawing • ISO 216 216 paper paper sizes sizes,, e.g. e.g. the the A4 paper size • ISO 406 406:19 :1987 87 Tech Technic nical al draw drawing ingss —Tolerancing of linear and angular dimensions
—Dimensioning and tolerancing • ISO 1660 1660:19 :1987 87 Techn Technic ical al drawi drawings ngs — of profiles
—Conventional representation • ISO 2203 2203:19 :1973 73 Techn Technic ical al drawi drawings ngs — representation of gears • ISO 3040 3040:19 :1990 90 Techn Technic ical al drawi drawings ngs — —Dimensioning and tolerancing -- Cones • ISO 3098/1:1 3098/1:1974 974 Technic Technical al Drawing Drawing - Letteri Lettering ng - Part I: I: Currentl Currently y Used Characters • ISO 4172:1991 4172:1991 Techni Technical cal drawing drawingss -- Construc Construction tion drawin drawings gs -Drawings for the assembly of prefabricated structures • ISO 5261 5261:19 :1995 95 Techn Technic ical al drawi drawings ngs — representation of —Simplified representation bars and profile sections
A size chart illustrating the ISO A series
—Scales • ISO 5455 5455:19 :1979 79 Techn Technic ical al drawi drawings ngs —
described in ISO 216.
• ISO 5456 5456 Technica Technicall drawings drawings -- Projec Projection tion methods methods • ISO 5456 5456-1: -1:199 1996 6 Techni Technical cal draw drawing ingss —Projection methods —Part 1: Synopsis • ISO 5456 5456-2: -2:199 1996 6 Techni Technical cal draw drawing ingss —Projection methods —Part 2: Orthographic representations representations • ISO 5456 5456-3: -3:199 1996 6 Techni Technical cal draw drawing ingss —Projection methods —Part 3: Axonometric representations representations • ISO 5456 5456-4: -4:199 1996 6 Techni Technical cal draw drawing ingss —Projection methods —Part 4: Central projection • ISO 5457:1999 5457:1999 Technica Technicall product documen documentati tation on -- Sizes and layout layout of drawing drawing sheets • ISO 5459:1981 Technical drawings --- Geometrical Geometrical tolerancing tolerancing -- Datums and datum-systems datum-systems for geometrical tolerances • ISO 5845 5845-1: -1:199 1995 5 Techni Technical cal draw drawing ingss — representation of the assembly of parts with fasteners —Part 1: —Simplified representation General principles • ISO 6410 6410-1: -1:199 1993 3 Techni Technical cal draw drawing ingss — —Screw threads and threaded parts —Part 1: General conventions
—Simplified representation • ISO 6411 6411:19 :1982 82 Techn Technic ical al drawi drawings ngs — representation of centre holes • ISO 6412 6412-1: -1:198 1989 9 Techni Technical cal draw drawing ingss — —Simplified representation of pipelines -- Part 1: General rules and orthogonal representation representation
—Representation • ISO 6413 6413:19 :1988 88 Techn Technic ical al drawi drawings ngs — Representation of splines and serrations • ISO 6414:1 6414:1982 982 Techni Technical cal drawings drawings for for glassw glassware are
—Requirements for microcopying • ISO 6428 6428:19 :1982 82 Techn Technic ical al drawi drawings ngs — • ISO 6433:19 6433:1981 81 Technic Technical al drawing drawingss -- Item Item refer references ences • ISO 7200 7200:19 :1984 84 Techn Technic ical al drawi drawings ngs — Title blocks
—Symbols for geometrical tolerancing -- Proportions and dimensions • ISO 7083 7083:19 :1983 83 Techn Technic ical al drawi drawings ngs — • ISO 7437:1990 Technical drawings --- Construction Construction drawings drawings -- General rules for execution of production production drawings for prefabricated structural components • ISO 7518:1983 Technical drawings --- Construction Construction drawings drawings -- Simplified representation representation of demolition and rebuilding • ISO 7519:1991 Technical Technical drawings drawings -- Construction Construction drawings drawings -- General principles principles of presentation for general arrangement and assembly drawings
—Fundamental tolerancing principle • ISO 8015 8015:19 :1985 85 Techn Technic ical al drawi drawings ngs — • ISO 8048:1984 Technical Technical drawings drawings -- Construction Construction drawings drawings -- Representation Representation of views, views, sections sections and cuts
ISO 128
• ISO 8560:1986 Technical Technical drawings drawings -- Construction Construction drawings drawings -- Representation Representation of modular modular sizes, lines and grids
—Construction —Representation • ISO 8560 8560:19 :1986 86 Techn Technic ical al drawi drawings ngs — Construction drawings — Representation of modular sizes, lines and grids • ISO 8826 8826-1: -1:198 1989 9 Techni Technical cal draw drawing ingss — —Rolling bearings —Part 1: General simplified representation
—Rolling bearings —Part 2: Detailed simplified representation • ISO 8826 8826-2: -2:199 1994 4 Techni Technical cal draw drawing ingss — • ISO 9222 9222-1: -1:198 1989 9 Techni Technical cal draw drawing ingss — —Seals for dynamic application —Part 1: General simplified representation
—Seals for dynamic application —Part 2: Detailed simplified representation • ISO 9222 9222-2: -2:198 1989 9 Techni Technical cal draw drawing ingss — —Draughting film with polyester base —Part 1: • ISO 9958-1: 9958-1:1992 1992 Draught Draughting ing media media for for technica technicall drawings drawings — Requirements and marking
—Natural tracing paper • ISO 9961:19 9961:1992 92 Draught Draughting ing media media for for techni technical cal drawi drawings ngs — • ISO 1020910209-1:199 1:1992 2 Technic Technical al product product documenta documentation tion —Vocabulary —Part 1: Terms relating to technical drawings: general and types of drawings
—Tolerancing of orientation and location —Projected tolerance zone • ISO 1057 10578:1 8:1992 992 Tech Technic nical al drawi drawings ngs — • ISO 1057 10579:1 9:1993 993 Tech Technic nical al drawi drawings ngs — —Dimensioning and tolerancing —Non-rigid parts • ISO 13567 is an intern internatio ational nal Computer Computer-aid -aided ed design design (CAD) layer layer standar standard. d. • ISO 1371 13715:2 5:2000 000 Tech Technic nical al drawi drawings ngs — —Edges of undefined shape —Vocabulary and indications
—Simplified representation • ISO 1578 15786:2 6:2008 008 Tech Technic nical al drawi drawings ngs — representation and dimensioning of holes
References [1] ISO 128-1:2 128-1:2003 003 Abstrac Abstractt (http:/ (http:/ / www.iso. www. iso.org/ org/ iso/ iso/ iso_catalogue/ iso_catalogue/ catalogue_tc/ catalogue_tc/ catalogue_detail.htm?csnumber=3 catalogue_detail.htm?csnumber=32462). 2462). Accessed 1 March 2009. [2] ISO ISO 128 128 (http (http:/ :/ / www.techstreet. www. techstreet.com/ com/ cgi-bin/ cgi-bin/ detail?product_id=23666) detail?product_id=23666) techstreet.com, 2009.)
3
Article Sources and Contributors
4
Article Sources and Contributors ISO 128 Source: http://en.wikipedia.org/w/index http://en.wikipedia.org/w/index.php?oldid=480346013 .php?oldid=480346013 R'n'B, Sobreira, Squids and Chips, Woohookitty, 3 anonymous edits
Contributors:
Amakuru, Davehi1, J04n, JamesAM, Jncraton, John of Reading, Lilac Soul, M-le-m ot-dit, Mdd, Nihiltres,
Image Sources, Licenses and Contributors Image:A size illustration.svg illustration.svg Source: http://en.wikipedia.org/w/ind http://en.wikipedia.org/w/index.php?title=File:A_size_illustrati ex.php?title=File:A_size_illustration.svg on.svg Bromskloss, Haytham abulela, Nagy, Pallbo, Sven, WikipediaMaster, 9 anonymous edits
License Creative Commons Attribution-Share Alike 3.0 Unported //creativecommons.org/licenses/by-sa/3.0/
License:
Creative Commons Attribution-ShareAlike 3.0 Unported
Contributors: