JP33 Service Manual

JP-33 SERVICE MANUAL

Revision 5.03 Issue: 2004/04/01

Service Manual JP-33 Automatic Film Processor Maintenance and a nd Technical Technical Support S upport

Corporate: JUNGWON PRECISION IND. I ND. CO., LTD www.jpi.co.kr Woolim Wo olim e-Biz center #608,170-5, Kuro-3-dong, Kuro-gu, Seoul, Korea, 152-847 TEL : 82-2-2108-2580 FAX : 82-2-2108-1180

U.S. Office:

JPI AMERICA, INC www.jpiamerica.com 22-36 Harman Street, Ridgewood, NY 11385 TEL: 01-718-417-3020

-1-

Fax: 01-718-417-6641


This chapter provides instructions for cleaning and preventive maintenance of the JP33, and explains how users may keep the processor in optimal condition. Only experienced technicians should install the JP-33. The technicians who install the unit should review the JP-33 Instruction Manual before installation and should strictly follow all guidelines of the manual.

The technician should instruct and train all users to perform daily daily

and weekly maintenance and provide users with blank copies copies of maintenance maintenance records.

We

highly recommend that an experienced technician perform the monthly and annual maintenance.

A proper maintenance maintenance program will guarantee trouble free use with optimal

performance.

Use of Maintenance Record Use the maintenance record as a guideline and to log daily, weekly, monthly and annual maintenance performed. performed. The user must keep records records for technician evaluation. warranty will be void if maintenance is not performed properly. Do not use the original original maintenance record; record; copies should be made for for use.

-2-

The JP-33


Maintenance Record X-Ray Film Processor JP-33 m r e T

Check Item Clean feed tray

D

Clean film receiver

D

Clean Roller by cleaning film

D

Check Chemical Level

D

Check Hose Plumbing

D

Clean DEV Rack

W

Clean FIX Rack

W

Clean Wash Rack

W

Clean Wash Tank

W

Clean Drain Filter

W

Check Roller Damage or Scratch Check Roller Spring Tension Clean DEV, FIX, Wash Rack Clean DEV, FIX, Wash Tank & O/F Check Hose Clamp, Plumbing Check Lubricant Clean Valve of Pumps Check Worm & Drive Gear

X

Term Code: D – Daily, W – Weekly M – Monthly, Month ly, Y - Yearly Date of (J an, Feb, March, April, May, June, July, Aug, Oct, Sep, Nov, Dec,) Year Year 20____

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

W W M M M M Y Y

Please cross out each box when task is complete.

Do not use the the original maintenance record; record; extra copies should should be made for use. -

-

3


Maintenance Program

- Cleaning

Cleaning Cleaning is one one of the most important factors in the maintenance program.

It is very important for proper

operation. Stains or contamination on the unit from water or chemicals may cause damage and corrosion. It may also seriously affect the unit’s performance, which may deteriorate image quality.

Caution: Caution:

The temperature temperature of water used for cleaning the tanks should not be more than 129 ° F (54° C).

The technician cleaning the unit should follow the instructions provided in the service manual. Do not use any abrasive detergent or material to clean the unit.

Warning:

Only use neutral detergent detergent and soft lint-free material.

For safety purposes, purposes, unit should should be turned off off while performing performing maintenance and /or service

on mechanical and electrical parts (gear, shaft, PCB, pumps, etc.)

Daily Cleaning

The daily cleaning should be performed in accordance with the maintenance schedule.

1. Clean the feed tray A. Use a damp lint-free cloth to clean the film inlet and inside the feed tray. All chemical residues should be cleaned B. Make sure the surface is dry after cleaning, use a dry lint-free cloth if needed.


Maintenance Program

- Cleaning

Cleaning Cleaning is one one of the most important factors in the maintenance program.

It is very important for proper

operation. Stains or contamination on the unit from water or chemicals may cause damage and corrosion. It may also seriously affect the unit’s performance, which may deteriorate image quality.

Caution: Caution:

The temperature temperature of water used for cleaning the tanks should not be more than 129 ° F (54° C).

The technician cleaning the unit should follow the instructions provided in the service manual. Do not use any abrasive detergent or material to clean the unit.

Warning:

Only use neutral detergent detergent and soft lint-free material.

For safety purposes, purposes, unit should should be turned off off while performing performing maintenance and /or service

on mechanical and electrical parts (gear, shaft, PCB, pumps, etc.)

Daily Cleaning

The daily cleaning should be performed in accordance with the maintenance schedule.

1. Clean the feed tray A. Use a damp lint-free cloth to clean the film inlet and inside the feed tray. All chemical residues should be cleaned B. Make sure the surface is dry after cleaning, use a dry lint-free cloth if needed. Note: Be Note: Be careful not to touch the film sensor lever when cleaning the feed tray.

2. Cleaning the film receiver Apply a damp, lint-free cloth to clean the film receiver on the top cover. Make sure the surface is dry after cleaning; use a dry lint-free cloth if needed.

3. Clean roller with Cleaning-Film We recommend using 3~5 pieces of cleaning film. Continuously feed the cleaning film to get rid of any impurities (artifacts) on the rollers and film guides. This step is not mandatory if the weekly inspection is performed regularly or scratches are found on image. In the event there are scratches on the image, please refer to trouble shooting section 1.3.

-

-

4


Maintenance Program

- Cleaning

Weekly Cleaning Caution! When cleaning tanks and roller, do not use any abrasive material that can damage the surface.

Caution! When removing the rack assembly from from the unit, make sure the unit is turned turned off.

Do not spill

chemicals or water into other tanks or onto other parts of the unit, such as the control panel. In the event water or chemistry spills onto any electrical parts immediately dry the part using a dry lint-free cloth and a blow dryer.

1. Cleaning the DEV, FIX, WASH rack

Caution: When removing and cleaning racks, note that the worm wheel (gear) maybe lubricated with grease.

Avoid allowing grease grease to come in contact with clothing, rollers, gears gears or any other part of the

rack.

A. Carefully remove rack covers. B. Be careful not to spill chemicals while removing the DEV, DEV, FIX and WASH racks. C. Use a lint-free cloth to clean the rack and rack cover. If required, apply alcohol or a neutral detergent onto a soft sponge to remove foreign substances on the surface. The surface of each roller should be thoroughly cleaned out.

Note: Note: Soft materials like a sponge should be used to clean the roller. Do not use abrasive materials (scrubbing brush, etc.).

Abrasive material may damage damage the surface of rollers. Do not

apply too much pressure; it may damage the roller tension spring.

D. Check the rollers and the operational condition of each rack. Check the condition of film guides and make sure they are mounted properly.

2. Cleaning the wash tank A. The wash tank should be cleaned once a week. B. Open the wash drain valve to empty the wash tank. C. Use a soft sponge and/or soft scrubbing brush with lukewarm water to clean the base and walls inside the tank.

-

-

5


Maintenance Program

- Cleaning

3. Cleaning the drain filter of the DEV, FIX, WASH tanks A. In the event there is trouble with the drain filters in the tanks (clogging or obstructions by leftovers), problems with the circulation and replenishment of the chemicals may occur. occur. This may accelerate contamination of chemicals and can rapidly increase or decrease the temperature of the chemistry. B. Remove all the drain filters from tanks. C. Wash Wash residue and all foreign objects off by running the filter under lukewarm water. D. Make sure the filter mesh is not damaged. E. Install the cleaned drain filter back in its original location.

4. Place all parts and rack assemblies back securely in their original location.

-

-

6


Maintenance Program

- Cleaning

Monthly Cleaning All rack assemblies and tanks must be cleaned thoroughly thoroughly every month.

This procedure may take up to

two hours.

Caution! Make sure unit is turned off before performing monthly cleaning.

1. Clean the DEV, FIX, WASH racks A. Open the drain valve to remove the developer, fixer and water from tanks. B. Remove the racks from the unit and clean the racks. (Follow weekly cleaning procedure procedure on page 5) C. Remove all drain filters and rinse them with lukewarm water. D. Check the condition of each rack and rack side plates. Rotate rollers, by turning worm wheel (Gear) in one direction, to make sure rotation is smooth.

Note: Fixer Note: Fixer rack has a higher potential for damage than the developer rack. This originates from the chemical reaction of the fixer. Therefore, the conditions of the fixer rack (rollers, gears, guides, side plates and bushings) must be checked thoroughly and frequently. frequently.

2. Clean the DEV, FIX, WASH tanks and OVER FLOW line A. With racks out of the the tanks, close drain valves and pour lukewarm water into the tanks. brush clean the base and walls of each tank.

With a soft

Once finished, open drain valves to remove remove water.

B. Pour lukewarm water into the overflow hole to remove foreign substances. C. Once you have cleaned all the tanks, make sure to close the drain valves, fill each tank with lukewarm water then mount all the racks and turn the unit on. You should run the processor for approximately 15 minutes while you are checking the circulation of the water and the operation of each rack. D. Once this is complete drain the w ater and follows procedures for filling chemistry. (Page 10)

-

-

7


Maintenance Program

- Inspection

Preventative maintenance Daily Inspection 1. Check the tank levels Make sure that the chemistry inside the tanks is at at the appropriate appropriate level.

Also make sure to check the

level of the replenishment tanks.

2. Check the hoses and plumbing Check all hose and connections connections for leaks. leaks. immediately.

If there are any leaks contact your service center

Check each hose for kinks and make the appropriate adjustments to eliminate the kinks.

Weekly Inspection 1. Check the roller and film guide Check the surface of roller for any damage, scratch or pollutants. Check the film guide for any damage. Make sure all film guides are mounted firmly in their location. 2. Check the roller spring tension A. The spring tension supporting the roller is a very important part of the rack. B. The spring tension should firmly support the roller and it should not be loose. -

If the spring tension supporting the dryer exit rollers is loose, the film may not be guided out properly and may be lost inside the unit or Jam the unit.

-

If the spring tension supporting the squeegee rollers (rubber rollers) is loose, they will not squeeze (dry) the chemistry or water, which will affect the image quality.

-

The spring tension should not be be too hard. hard.

This will make it difficult for the racks racks to rotate

smoothly. In this case, the rack will jump and/or film will jam. -

The spring tension should be the same on both ends of the roller. If not, due to uneven tension the film may be guided off alignment and jam.

-

-

8


Maintenance Program

- Checking and Inspect

Monthly Inspection 1. Check the hoses, clamps and plumbing -Do not tighten the hose clamps too much. Clamps that are too tight may cut hose and cause leakage, which may result in damage to pumps and electrical components. -Check hose for kinks or cracks. 2. Check lubricated parts Remove old lubrication and apply new lubrication for appropriate parts in accordance with the oiling schedule.

A. Remove old lubricant Old lubricant should be removed before applying new fresh lubricant. The absorption of dust or other foreign substances on the old lubricant may cause unwanted friction. B. Cleaning Before applying new lubricant, use a brush to remove any foreign material or pollutant from the gears. C. Lubricating pointer Main drive shaft and Bracket

Oil/Teflon Oil/Teflon oil

Worm Gear, Drive Gear

Oil/Teflon oil

Main Motor Sprocket and Chain

Grease

Annual Inspection 1. Check the RPL. Pump Valve A. Unscrew the valve-fixing cap off the replenishment pump. B. Remove the valve from the pump to prevent damage. C. Soak the separated valve in warm water. Physically check the valve for pollutant. D. Carefully place the clean and checked valve back into the pump. Make sure the valve is positioned properly. properly. E. Screw the valve-fixing cap back onto pump. F. Handling of the valve of RPL pump should be in strict accordance with the above instructions and other instructions in this manual.

2. Check the worm drive and worm wheel (gear) A. The worm drive and worm wheel (gear) are critical parts of the transport system. are exposed to great pressure.

These two parts

Therefore, it is important to carefully examine the parts for wear

and tear. B. Carefully check the worm drive and worm wheel (gear) for wear and tear, and replace the part when needed.

-

-

9


Maintenance Program

- Change Chemical

When & How to Replace Chemicals Important: The chemistry’s condition is important important for proper film processing. contaminated chemistry will lead to poor poor images.

Exhausted and/or

Since the processor is used in the final stage of

generating an image, it is normally blamed for poor image quality, overlooking the chemistry. Before assuming the poor image quality is due to a processor problem we highly recommend that the chemistry be checked. 1. Generals When is to replace the Chemistry. : Refer to trouble shooting guide section 4, reasons for poor image quality. When there are no problems, chemistry should be replaced in accordance to the chemical manufacturer’s manufacturer’s guidelines.

2. Procedure for replacing the chemistry 1) Removing old chemistry. -

Before opening drain valves, make sure the drain hoses are inserted inside the tank or drain.

-

Remove all the racks (DEV, FIX, WASH). Be careful worm wheel (gear) is lubricated. DO NOT GET GET LUBRICANT LUBRICANT ON CLOTHING CLOTHING OR OTHER PARTS OF OF THE RACK. RACK. Open top cover  remove rack cover  open rack locks  remove DEV, FIX, WASH racks  be careful not to spill chemicals on the floor, on any electrical components and keep the chemicals away from the operator’s body and clothes.

-

Open drain valve to drain the old chemicals.

2) Waste disposal Disposal of waste should be performed in accordance to local rules and regulations.

-

-

10


Maintenance Program

- Change Chemical

3) Clean processor before adding new chemistry -

-

Cleaning tanks (Close drain valves) 

With lukewarm water rinse each tank.



Drain the used water by opening the drain valves.



Dry all tanks with a lint-free cloth



Close the drain valve after cleaning all the tanks.

Cleaning of rack submerge worm gear in water. water. Important: Do not submerge

Grease Grease from worm gear may loosen

and stick to other parts of rack, also when handling worm gear make sure to not get grease on other parts of rack.

Soak the three racks in water separately, separately, or clean each rack with running water while rotating the worm wheel (gear). Be careful not to damage the roller surface during cleaning.

-

Cleaning of replenishment tanks Wash out the tanks with lukewarm water. wat er. Make sure there are no foreign materials inside the tanks.

4) Prepare new chemicals

-Please follow chemical manufacturer’s manufacturer’s mixing process and guidelines. 5) Filling processor tanks

Important: To prevent cross contamination; make sure to add fixer before developer. Then with a damp lint-free cloth wipe clean developer developer tank. tank.

Make sure sure to clean any

fixer residue.

A.

Add fixer into the fixer tank by using the pitcher provided with the processor. processor. - Wash Wash out the measuring cup with running water. - Fill the fixer tank. - Pour about 2~2 1/2 pitchers into the tank. Make sure to fill the tank up to overflow level.

B.

Filling developer tank: make sure the tank is clean and the pitcher is thoroughly clean. To fill developer tank, follow the same method used to fill fi ll the fixer tank .

Be careful not to mix the developer and fixer when handling the chemicals. C.

Fill washer tank with water up to overflow level. -

-

11


Maintenance Program

- Change

6) Install replenishment tanks -

Place replenishment tanks in i n their proper location under the processor.

-

Connect hoses hoses or insert insert hoses into tanks.

-

Color codes of hoses used with the processor

Refer to color codes and picture to prevent error. error.



Red: Developer



Blue: Fixer



Clear: Washer Washer (Or Black six-foot si x-foot hose with ¾ i nch fittings).

7) Inspection Check all hoses and connections for leaks. Clean any spilled chemicals inside and outside the processor

8) Installation of racks and final testing. -

Install the cleaned rack in the marked location Make sure main worm gears are positioned properly on the worm drive. Lock racks into place

-

Cover all racks.

-

Turn the power on. Check the operation of the racks and make sure there are no unusual noise, leaks or odors.

-

Place top cover into position.

9) Check for proper operation by running one test film.

-

-

12


Technical Support This chapter provides technical supports for technical service personnel.

Part I. Trouble Shooting. -------------------------------------- page 14 Part II. Developer-Temperature Developer-Temperature calibration. ---------------- page 30 Part III. AC-Power voltage setting (220/240V). ----------- page ----------- page 31 Part IV. How to replace key parts. --------------------------- page 35 Part V. Location of Components ----------------------------- page 43 1. Location of Electrical Components 2. Location of Developer Rack Components 3. Location of Fixer Rack Components 4. Location of Washer/Dryer Rack Components 5. Location of the Main Drive Shaft Components Part VI. Electrical schematics ------------------------------- page 49 1. Block-Diagram of Electrical 2. Schematic Circuit Diagram 3. Microprocessor Sequence Seque nce Table Table Part VII. Part List --------------------------------------------- page 53

-

-

13


Technical Support

- Trouble Shooting

PART I -Trouble Shooting Please refer refer to this trouble-shooting trouble-shooting guide before contacting technical support. support. provides possible causes for the problems you are are experiencing. experienci ng.

This guide

Some simple checks or

minor adjustments on your part may eliminate the problems and restore proper operation. To resolve a problem you will need to check the trouble-shoo t rouble-shooting ting table of contents to find the problem or or related related problems. problems.

Once you have identified the problem problem you may may need to use

one or more of the provided provided solutions to eliminate the problem. problem.

In the event event you have tried

the remedies indicated but the problem is not solved; contact technical support as soon as possible.

Table of Contents 1. General problems 1-1. Cannot insert film, or unit does not activate when film is inserted. 1-2. Unit continues to operate as if film is being processed (non-stop). 1-3. Scratch or marking on film. a. White or black streaks parallel to film feed direction. b. Scratches or markings on the film that are perpendicular to film feed direction and are similar in size, distance and location. c. Scratches or markings on the film that are not similar in size, distance or location. 1-4. Film Jam or lost film in processor. 1-5. Chemistry is not replenishing. 1-6. Replenishing rate is too high or too low. 1-7. Unit continuously replenishes. 1-8. Film is not dry. dry. 1-9. During processing you hear squeaking.

2. Electrical problems 2-1.

Unit does not turn on.

2-2.

Circuit breaker continuously trips.

2-3.

Unstable operation, the unit repeatedly runs and stops.

2-4.

Display panel does not work.

2-5.

Buzzer is not working

2-6.

Main motor is not working.

2-7.

Developer displayed temperature not the same as actual temperature.

2-8.

Over or under supply of water.

2-9.

Dryer heater does not work.

2-10. DEV heater overheats.

-

-

14


Technical Support

- Trouble Shooting

3. Mechanical problems 3-1. The unit squeaks during operation. 3-2. Rack jumps and rattles. 3-3. Wrinkled film. 3-4. Film exits unit at an angle.

4. Poor image quality. 4-1.

High contrast.

4-2.

Low contrast.

4-3.

Film is milky.

4-4.

Film surface is spotty. spotty.

4-5.

Wet film.

4-6.

Dirty film.

4-7.

Film is sticking st icking in dryer.

4-8.

Film emulsion is coming off in developer.

4-9.

Increased base fog.

4-10.

Scratches or markings on film.

4-11.

Sandy film

4-12.

Developer turn dark

4-13.

Strong Ammonia smell from processor.

4-14.

Fixer color is milky.

-

-

15


Technical Support

- Trouble Shooting

Troubleshooting general problems 1-1. Problem Cannot insert film, or unit does not activate when film is inserted.

Check Film Sensor manually. manually.  

Film Sensor is located inside the Feed Tray. : It can easily be seen and accessed when feed tray cover is opened. Check the operation of the sensor by a dummy film inserting. : If the magnetic sensor is not working properly because of obstructions, sensor bar can not sensing (: up) or recovering position (: down).

You can repair a obstruction by sensor adjusting.

You check wiring by bellow diagram.

-

-

16


Technical Support

- Trouble Shooting

Check to see if main motor is operating.  Remove the top-cover and check if the motor is operating. : If motor is not functioning properly, properly, contact tech support. properly.  Check if DEV Rack is placed in tank properly. : Make sure worm wheel (gear) is resting properly and securely on worm drive. Index: instruction manual page 19 “4.6.3. Check installing installing the Rack.” Check if the tension spring supporting DEV Rack Roller is loose and rollers are running idle.  : Adjust the spring tension manually for proper operation.

If rollers are running idle because of the Tension Spring is loose, bend the T Tension ension Spring so that it will increase tension on the roller.

1.2 Problem Unit continues to operate as if film is being processed (non-stop). (non-stop). 

Control Panel displays “Feed-In” and the Feed Time continues to increases.



Main motor is on and unit continues to replenish chemistry.



Next film feed in indicator does not prompt.

Check Film Sensor manually.  Film Sensor is located under the Feed Tray. : It can be easily accessed when feed tray is retracted.  If the Sensor Lever is not returning to its original position and is stuck, a manual adjustment will have to be made. If the lever gets stuck on any part of the unit and does not return to its original position, manual adjustments will will have to be maid to avoid obstacles. Check if there is any chemical residue that is preventing the sensor from working properly. properly. To correct this problem, clean the lever and the area around the sensor with an alcohol or water dipped lint-free cloth, make sure not to bend lever out of shape. Note: In case version 2.0, Film Sensor is located inside the Feed-Tray You can see on this manual page 16th.

-

-

17


Technical Support

- Trouble Shooting

1.3 Problem Scratches or Markings on developed Film. A. There are white or black lines parallel to film feed direction. Check if the Film-Guide is contaminated, damaged or dislocated.  Clean the Film Guide or replace the damaged Film Guide.  Check if the Film Guide is bent. Make manual manual adjustments adjustments if necessary. necessary. Check if the film is being feed on an angle or is exiting on an angle.  Check if the user inserts the film on an angle? rollers are not too tight. If so, make manual manual adjustment  Make sure tension springs on the rollers  Make sure unit is level. B. There are scratches or markings on the film that are perpendicular to film feed direction and are similar in size, distance and location. Check if there is any damage or contamination on the surface of t he Roller. Roller. 

Clean and/or replace the Roller. Roller.

C. There are irregular scratches or markings. Check if there is any damage of contamination on the part of Feed Tray. Tray. 

Clean the Feed Tray.

Check if there was damage or contamination on the film before developing.  Inspect Film Cassette for contamination or damage.  Check if the damage arises during use of ID Printer. Printer.

1.4 Problem Film jammed or lost in processor. Check if the Rack is dislocated. 

Make sure unit Base and Unit are level.



Make sure racks are positioned properly in place.



Make sure worm wheel (gear) is resting properly and securely on worm drive.

Check Roller Tension Tension Springs. 

If the Tension Tension Springs are too loose or tight: 

Too loose: The film will not be guided properly.



Too tight: The film may not be able to go in between rollers

Film Guide is dislocated or transformed. Correct the location of the Film Guide by making manual adjustments

-

-

18


Technical Support

- Trouble Shooting

1.5 Problem A chemical is not replenishing. Air is in the pipe or hose. 

Remove air bubbles by opening the Drain Valve to release air.



Reduce the size of RPL Hose if it is to long.

RPL rate is to low 

Set RPL Time over 30 seconds. : In this case 100ml o f chemical is supplied for 30 seconds to develop a sheet of film.



Set RPL Time as over “00” in Setting Mode. : Replenishment is supplied automatically according to the size of film.

REVIEW REPLENISHMENT RATE CHART IN SECTION 1.6 OF TROUBLE SHOOTING GUIDE

Check and make sure there are no particles inside hoses and pipes 

Check the pipes connecting to replenishment tanks



Check if there is any alien substance or dried chemicals in the p ipe and hoses.

.

1.6 Problem Replenishment rate is too high or too low.

Adjust the replenishment rate. 

Set “RPL Time” Time” high/low in System Setting Mode.



The RPL is factory set at “00”: RPL “00” is for standard processing conditions.

JP-33 Film Processor is set-up to replenish Developer and Fixer according to the following chart. Please program the RPL time accordingly to required specifications for your applications.

Replenishment rate of DEV, FIX chemical (bases on 14” x17” film = 50sec loading time) Set RPL Time in sec.

RPL pump capacity (ml/sec.) Fixer Developer

00

10

20

30

40

60

100%

4.16 ml/sec

200ml

42ml

83ml

125ml

166ml

250ml

80%

3.33 ml/sec

160ml

33ml

67ml

100ml

133ml

200ml

Note: The IW IWAKI-bellows AKI-bellows type pumps used on the JP-33 has a mechanical cam adjustment screw. If your processing needs requires increasing the RPL, you can adjust the cam up to 100% of the pumps capacity.

-

-

19


Technical Support

- Trouble Shooting

1.7 Problem Chemicals are being supplied without stopping. Check the operation of the Film Detection Sensor. Sensor. 

Check feed sensor, sensor, refer to trouble shooting section 1.2 .

1.8 Problem Film is not drying Check if the Dryer air is warm or cold. 

If the dryer air is cold, then the dryer dryer heater is malfunctioning. malfunctioning.

Contact Technical Technical

support ASAP. ASAP. 

If the dryer air is warm, then the fixer may be exhausted or the washer is contaminated. Replace the fixer and/or cleaning water.



Check if dryer vents in the Dry Rack are aligned properly. properly.

1.9 Problem

During processing you hear squeaking Check for air bubbles in re-circulation pump or if the pump is empty. 

Check if there is sufficient chemical in the tank.



Drain the air bubbles. : How to drain air bubbles is described in trouble shooting section 1.5.

-

-

20


Technical Support

- Trouble Shooting

Troubleshooting for Electrical problems When dealing with electrical problems make sure to unplug unit from power supply. If the operator does not have professional knowledge in electricity, don’t investigate or take any actions other than described below. below.

2.1 Unit does not turn on. Are you receiving electricity? 

Power outage.



Check your circuit breaker. Please check and correct the Voltage Voltage for the processor  250V?  220V? 240V? 



The main fuse is blown. 

Replace the fuse.

Make sure to use use the proper fuse. (SPT 5x20. current rating 20A, Voltage Voltage

rating 250V) 

The location of the fuse and how to replace the fuse is located in the operation manual (Page 7/2.2.1)

2.2 -Circuit breakers continuously trips.

Check if there is electricity leakage or overload in the unit. 

Check if there is any leakage of chemical or water? Clean leaks dry with a blow dryer.



Check if there is a burning smell or burn marks in the unit.



Make sure the breaker is rated to handle all utilities connected to it.

Check if breaker switch is too old 

Connect the power plug to another power source.



Make sure your breaker switch is rated to produce the required power supply needed for the processor and any other devices on the same power power supply line.

-

-

21


Technical Support

- Trouble Shooting

2.3 -Unstable operation the unit turns on and off. : Or the display board blinks .

Check if there is a voltage or a current change?  Main power supplied may be lowered temporarily. Turn off the power for 2 or 3

minutes and resume operation.  If you use other equipment on the same power supply line, we highly recommend

contacting a professional electrician to make sure the breaker is rated to handle all your equipment needs.

Power can be cut temporarily because of the interference of the

other unit(s).

2.4 -Display panel does not work Open top cover and check the control panel. 

Check if there is any chemical or water on Control Panel, if so dry with a blow dryer.

properly.  Check control board connections; make sure they are plugged in properly.

2.5-Buzzer is not working Check if the film detection sensor is working properly.

REFER TO TO TROUBLE SHOOTING SHOOTING SECTION SECTION 1.2

2.6 -Main Motor is not working. Check if the feed sensor is working properly.

REFER TO TO TROUBLE SHOOTING SHOOTING SECTION SECTION 1.2

-

-

22


Technical Support

- Trouble Shooting

2.7 -Developer display temperature not the same as actual temperature. Are there volatile changes in environment (: room temperature)?

If temperature in dark room is unstable, wait until the temperature is stabilized and recheck it. Check the chemical circulation 

In the event there are air bubbles in the hoses or pumps  Refer to trouble shooting section 1.5.



Chemical is not circulated because of contamination and clogging of Drain Filter Clean Drain Filter.

2.8- Over or under supply of water Adjust the water supply.  Check the water pressure, reduce or increase pressure as needed. Check the operation of the Film Detection Sensor.

REFER TO TROUBLE SHOOTING SHOOTING SECTION SECTION 1.2 Check the operation of the Water Level Sensor.  Make sure the level sensor behind the Wash Rack moves freely.

Remove any particles affecting the float and clean it to ensure the float moves freely. if the Level Level Sensor Bracket Bracket is is securely in in place. place.  Check if in place it will not function properly.

-

-

23

If the sensor sensor is not securel securely y


Technical Support

- Trouble Shooting

2.9- Dry Heater does not work. Is there any change in voltage? SHOOTING SECTION SECTION 2.3  REFER TO TROUBLE SHOOTING Dry Heater is defective.  If the heater is malfunctioning due to dry heater temperature fuse or thermostat, contact

technical support to replace heater.

2.10- DEV Heater overheats. Check if there is sufficient DEV and FIX chemicals in the Tank. Tank.  Check the developer and fixer tanks levels and also check replenishment tank levels. Check if there is air in DEV and FIX pipes.

If there is air bubbles in a pipe, hose or pump the heater can overheat because of poor circulation. Turn off power supply and open the Drain Drai n Valve Valve to drain air.

-

-

24


Technical Support

- Trouble Shooting

Troubleshooting for Mechanical problems. 3.1 The unit squeaks during operation There is noise because of friction of Main Motor Power Delivery (Power Delivery Gear).

Apply lubricant or Vaseline Vaseline on the Worm or Drive Gear where noise is apparent

.

3.2 Rack jumps and rattles. The rack is not positioned properly in it’s location.

s ecurley..  Make sure the rack is positioned properly and securley  Make sure the worm wheel (gear) is resting on the worm drive properly.  We recommend that you remove rack and re-install it. If Dry Rack is not positioned properly, aline the rack and make sure to lock it in place.  Insert the Dry Rack securley in place and then make sure worm wheel is resting

properly on worm drive.  Make sure rack is locked into place.  Check to make sure the rack locks are not broken or bent. Make sure the rack is aligned ali gned properly.  Place the Rack on a flat surface and make sure the rack sits properly on the side

plates (Flush).  If the side plates are not completely flush with the surface apply presure to corners of

the rack to make proper adjustments.

-

-

25


Technical Support

- Trouble Shooting

3.3 Wrinkled film. Caused when film jams in racks.

i s bent or out of shape (: out of square). Refer to trouble shooting  Check if the rack is section 3.2

properly.  Make sure racks are positioned properly. If a film jam position is identified, make ajustments in film guides as needed or check roller spring tension. Check the tension of the roller spring. Refer to trouble shooting shooting section 1.4.

Check if Film is being inserted properly 

Film should be inserted properly without tilting.

-

-

26


Technical Support

- Trouble Shooting

Troubleshooting poor image quality. 4.1 High Contrast 1.

Developer has too little starter. starter.

2. Not enough water in the developer Mixture. 3.

The washer temperature is too hot causing thermal (heat) contamination increasing the developer temperature.

4.

Wash water is not circulating or not supplied.

5.

Expired and degraded film.

6.

Film has been exposed to high heat.

7.

Cassette is leaking light.

8.

Replenishment rate is too high.

9.

Developer Temperature Temperature is too high.

4.2 Low Contrast 1.

The developer has too much starter.

2.

Improperly mixed developer. developer.

3.

Developer is contaminated.

4.

Depleted fixer.

5.

Oxidized (rusted) developer. developer.

6.

Degraded or improperly stored film.

7.

Developer temperature is not set high enough.

8.

Depleted developer due to low replenishment rate.

9.

Re-circulation of the developer has stopped.

4.3 Film is milky 1.

Fixer is depleted.

2.

Film is not washed properly (Low water level in wash tank).

4.4 Film Surface is spotty 1.

The dryer rack vents are dirty.

2.

The developer roller rack tension may need adjustment.

3.

Check for damage on rollers.

4.

Check for defective roller mechanism.

-

-

27


Troubleshooting poor image quality. 4.5 Wet film 1.

The chemistry is mixed with too much hardener or too much water has been used.

2.

Developer contaminated.

3.

Fixer does not have hardener added to it.

4.

Depleted fixer.

5.

Developer level is to low. low.

6.

Low replenishment of developer or fixer.

7.

Developer temperature is to low.

8.

Fixer temperature is too high.

9.

Chemistry is not being re-circulated.

10. The water flow may not be sufficient, check for blockage of water supply. 11. Dryer temperature too low.

4.6 Dirty film 1.

Improperly mixed chemistry.

2.

Developer in the processor is contaminated.

3.

Fixer has depleted.

4.

The developer has been depleted.

5.

Developer filter may be dirty or clogged.

6.

Developer temperature not set properly. properly.

7.

Rollers are dirty.

8.

Chemistry is not re-circulating.

9.

Dryer temperature is too high.

4.7 Film is sticking in dryer 1.

The developer is exhausted.

2.

The fixer is missing hardener.

3.

The replenishment rate for the fixer is to low. low.

4.8 Film emulsion is coming off in developer 1.

The film emulsion is defective.

2.

The developer is exhausted.

3.

There is no hardener in chemistry.

4.

Replenishment rate is low. low.

-

-

28


Troubleshooting poor image quality. 4.9

Increased base fog 1.

Starter has not been added to the developer.

2.

Fixer level is too low.

3.

Fixer has contaminated developer. developer.

4.

Developer replenishment rate is too high.

5.

Developer temperature is too high.

6.

Processor rollers are worn or dirty.

7.

Film has not been properly stored.

4.10 Scratches or markings on film 1.

Film was packaged loosely and has been damaged.

2.

Film loading area may be dirty.

3.

Fixer maybe depleted.

4.

Developer under replenished.

5.

Developer level too low.

6.

Fixer and developer may have been improperly mixed

7.

For additional remedies refer to Trouble shooting section 1.3.

4.11 Sandy film 1.

Dry temperature to high

2.

Air vents in dryer rack are dirty.

4.12 Developer turns dark 1.

Excessive heat has been applied applied to the developer. developer.

2.

Developers oxidized, make sure stored developer is in an enclosed container. container.

4.13 Strong ammonia smell from processor 1.

Chemistry has been contaminated.

2.

Developer and fixer were mixed.

4.14 Fixer color is milky 1.

Fixer is old and need to be replaced.

2.

Fixer was exposed to excessive heat.

-

-

29

Make sure standby mode is functioning. functioning.


Technical Support

- Temperature Calibration

PART II Temperature calibration instruction WARNING: DO NOT TOUCH OR ATTEMPT TO ADJUST VR2! VR2 is used for calibrating the high and low temperature of the developer and the fixer heater (In factory).

1. Tools needed for calibration

2.

1)

Thermometer (Calibrated)

2)

Small screw driver

Calibrating display to actual developer temperature. A.

Make sure the DEV temperature sensor is connected properly.

B.

Measure the actual DEV temperature by placing thermometer in or near the tank replenishment inlet. This will give you the most accurate temperature.

C.

If the displayed temperature is not the same as the actual temperature, using the screwdriver adjust VR1 until the “actual temperature value” is displayed.

3.

Do not make make any adjustments adjustments to VR2.

Adjustments to VR2 will prompt an error. error.

-

-

30


Technical Support

- AC power voltage setting

Part III AC power voltage setting (220V or 240V) This revision adapt to after Jun 1. 2003. Version Version 5.01. Please check and correct correct the Voltage Voltage for the processor processor,, 250V? / 220V? / 240V? 1. New 1. New applicant Transformer: Transformer: see attachment Drawing 1 Before Change) AC In-Put: 110volt, 220volt After Change) AC In-Put: 220volt, 240volt JP-33 of 220voltage field area has dual AC input 220volt, 240volt. How can use? - If field AC-voltage is 210volt ~ 240volt: use 220V terminal - If field AC voltage is 240volt ~ 260volt: use 240V terminal

2. Method of Application Voltage: Voltage: see attachment Drawing 2 Set voltage Jump-wire on PCB “220volt” marking Jumpwire

Use for 220volt

Use for 240volt

Connect a wiring

Remove or cut-off a wiring. wiring .

“240volt” marking Jump-

Remove or cut-off a

wire

wiring

Connect a wiring

3. Changing method of voltage and discriminate terminal of transformer: see attachment drawing 1. You can see the printing of part-no or part-no or shielding by Plastic Case, this side terminal is for AC in-put.

4. Reference: 1) Transformer Structure 2) Wiring and Mounting on the main PCB

-

-

31


-

-

32


-

-

33


-

-

34


-

-

34


Technical Support

- How to replace key parts

Part IV How to replace key parts IMPORTANT! •

Before replacing any part make sure the unit is turned off.

When replacing

electrical parts we recommend that the unit is unplugged from power source. •

Before replacing hoses, replenishment pumps, re-circulation pumps, solenoid

valve or developer heater, make sure the chemistry and/or water are drained. Working under the processor with chemistry in tanks is very dangerous; chemistry may spill on technician’s clothing and may spill and damage electrical parts.


Technical Support

- How to replace key parts

Part IV How to replace key parts IMPORTANT! •

Before replacing any part make sure the unit is turned off.

When replacing

electrical parts we recommend that the unit is unplugged from power source. •

Before replacing hoses, replenishment pumps, re-circulation pumps, solenoid

valve or developer heater, make sure the chemistry and/or water are drained. Working under the processor with chemistry in tanks is very dangerous; chemistry may spill on technician’s clothing and may spill and damage electrical parts.

-

-

35


Technical Support

How to replace key parts

A. Replacing replenishment pump Developer and/or Fixer. NOTE: The developer and fixer replenishment pumps are identical in appearance and wiring. Identify the correct pump before before execution.

If the two two pumps are being replaced,

make sure to replace each pump separately (Remove and replace pump one and then work on pump two).

1. Make sure unit is turned off and chemistry is drained. 2. Remove hoses from pump nipple. Note: When removing hoses be careful c areful not to apply pressure pres sure on the nipple. Twist hose off carefully but firmly. 3. Disconnect the green wire with yellow stripe (Ground wire). 4. Identify the two screws holding the pump in place and remove them. 5. Disconnect the remaining wires. 6. Only when replacing Developer pump, pump , remove the (red/burgundy) cover from the new pump, then replace it with the cover of the old pump. pump fits properly in its original position.

This will insure the

When replacing fixer pump use the new

pump with the new cover. cover. Note:

When replacing developer pump you may need to unscrew the fixer

pump to have access to the developer pump wires. 7. To install the new pump attach the two (green) power wires to the brown and white wires (Alternative current) wiring position does not not matter. matter.

Place and screw pump pump

into position, make sure bare wires are not exposed and wires are placed snug in original position. 8. Connect the hoses securely:

There are directional arrows on the nipples; the

arrows are pointing pointing in the direction the fluid will flow. flow.

Please identify the exit

hose and entry hose and connect them to the corresponding nipple. 9. Make sure to strap any loose wires and check for leaks.

-

-

36


Technical Support


-

-

37


Technical Support


B. Replacing developer/fixer heater NOTE: The developer/fixer developer/fixer heater is an external external inline heater. heater. This single heater is heating both the developer and fixer. fixer.

Make sure both tanks are drained before

removing the heater. 1. Make sure unit is turned off and chemistry is drained. 2. Remove hoses from heater by unclamping them. a. There may still be chemistry in the heater and hoses; it is a good idea to have a bucket or pitcher available to drain chemistry into. b. Make sure to mark each hose position for installation. 3. Identify and remove the two screws holding the heater bracket in place. a. There is a ground wire (green wire with yellow stripe) that is held in place by one of the screws. b. Make sure to remember the heater position. 4. Identify and remove the two wires connected to the heater. heater. PCB and the other to the power.

One is connected to the

When cutting the wires cut as close to the heater as

possible to provide sufficient wiring for the new heater. heater. 5. Place the new heater in position, then place and screw the heater bracket into position. Make sure to connect the ground wire (green wire with yellow strip) to the screw closest to it. 6. Connect and clamp all the hoses onto the appropriate nipple.

You will need need 4 small

clamps. 7. Connect the two red wires.

Make sure exposed wire is covered. covered.

8. Make sure to strap any loose wires and check for leaks.

-

-

38


Technical Support


Version

Revise Note: Note: The picture of new developer heater adapt to after October 2003. DEV and FIX heating FIX heating pipe new version

-

-

39


Technical Support


C. Replacing re-circulation pumps

NOTE: The developer and fixer re-circulation pumps are identical in appearance and wiring.

Identify the correct pump before execution.

If the two pumps are being replaced,

make sure to replace each pump separately (Remove and replace pump one and then work on pump two).

1. Make sure unit is tuned off and the appropriate chemistry is drained. 2. Remove hoses from pump by unclamping them. a. There may still be chemistry in the pump and hoses; it is a good idea to have a bucket or pitcher available to drain chemistry into. b. Make sure to mark each hose position for installation. 3. Identify and remove the two screws holding the pump in place. a. Make sure to remember the pump position. 4. Identify and remove the two wires connected to the pump. PCB and the other to the power. power.

One is connected to the

When cutting the wires cut as close to the pump as

possible to provide sufficient wiring for the new pump. pump. 5. Place and screw the new pump into position. 6. Connect and clamp all the hoses on to the appropriate nipple. You will need 2 small clamps. 7. Connect the two power wires.

Make sure exposed exposed wire is covered.

8. Make sure to strap any loose wires and check for leaks.

-

-

40


Technical Support


D. Replacing developer temperature sensor 1. Make sure unit is tuned off and the appropriate chemistry is drained. Note: Note: The developer temperature sensor is located in line between the Developer heater and the processors processors developer inlet.

It is also covered by black insulation

to insulate the sensor from thermal leakage. 2. Cut straps and remove the black insulation.

Make sure not to damage damage

insulation. 3. Unclamp and disconnect sensor from hoses. 4. Go to the front of the unit and open PCB access bay. Pull PCB out and remove the developer temperature sensor wires. Ref. To the electrical block diagram for detailed wiring information. 5. Take new sensor and wire according to electrical circuit block diagram. 6. Attach the sensor back on to the hoses and clamp into place (Need two clamps). 7. Strap insulation back onto the sensor to prevent any thermal leakage. 8. Make sure to strap any loose wires and check for leaks.

-

-

41


Technical Support


E. Replacing dry heater Construction of Dry Heater

-

-

42


Technical Support Part V

Location of Components and Part List

Location of Components and Parts List

1. Location of Electrical Components 2. Location of Developer Rack Components 3. Location of Fixer Rack Components 4. Location of Washer, Washer, Dryer Rack Components 5. Location of the Main Drive Shaft Components

-

-

43


Technical Support

Location of Components

1. Location of Electrical Components (18)

(20)

(16)

(17)

(19)

No

Part Name

Part No.

Quantity

1

Main PCB Assembly

F63-23001

1

2

Terminal Block

F63-21016

1

3

Main Switch

F63-21013

1

4

Fuse

F63-21015

2

5

SSR for Dry Heater (:110volt only)

F63-21018

1

6

Main Motor

F63-21001

1

7

Condenser for Main Motor

F63-21001 con

1

8

Blower Fan Motor

F63-21002

1

9

Condenser for Blower

F63-21003

1

10

DEV Heater

F63-21006

1

11

Dry Heater ( located on upper side)

F63-21012

1

12

Circulation Pump

F63-21009

2

13

Solenoid Solen oid Valve for Water

F63-21010 F63-210 10

12

14

RPL Pump

F63-21005

2

15

Thermostat of DEV Heater Outer

F63-21022

1

16

Level Sensor for Wash

F63-00012

1

17

Temperature Sensor of DEV

F63-00010

1

18

Film Sensor (inside Feed-Tray)

F63-00013

2

19

Limit Switch for Film Sensor

F63-00008

1

20

Pilot Indicator of Film Loading

F63-00014

2

-

-

44


Technical Support


2. Location of Developer Rack Components

Right Side View

No

Left Side View

Part Name

Part No.

Quantity

1

DEV rack side plate R

F63-11027B

1

2

DEV rack side plate L

F63-11027A

1

3

Spring A & C (Large type)

F63-13004A & B

4

4

Film Guide B Small

F63-11021

4

5

Film Guide A Large

F63-11020

1

6

Roller Bushing

F63-11026

21

7

Snap Ring Type “E”

F63-14002

15

8

Gear Worm Wheel

F63-11025

1

9

Gear A

0.8” D-cut

F63-11022

8

10

Gear C

1.5” D-cut

F63-11024

1

11

Gear B

1.5” Idle

F63-11023

2

12

Roller Rubber

F63-13001

8

-

-

45


Technical Support


3. Location of Fixer Rack Components (14)

Right Side View No

Left Side View

Part Name

Part No.

Quantity

1

FIX rack side plate R

F63-11028B

1

2

FIX rack side plate L

F63-11028A

1

3


F63-13004A & B

4

4

Film Guide B Small

F63-11021

3

5

Film Guide A Large

F63-11020

1

6

Roller Bushing

F63-11026

21

7


F63-14002

15

8

Gear Worm Wheel

F63-11025

1

9

Gear A

0.8” D-cut

F63-11022

8

10

Gear C

1.5” D-cut

F63-11024

1

11

Gear B

1.5” Idle

F63-11023

2

12

Roller Rubber

F63-13001

5

13

Roller PVC

F63-13002

3

14

Film Guide of Crossover

F63-11031

1

-

-

46


Technical Support


4. Location of Washer, Dryer Rack Components

(17)

Right Side View No

Left Side View

Part Name

Part No.

Quantity

1

Wash rack side plate R

F63-11029B F63-11029B

1

2

Wash rack side plate L

F63-11029A

1

3


F63-13004A & B

2

4

Spring B & D (Small type)

F63-13005A & B

10

5

Film Guide B Small

F63-11021

1

6

Film Guide A Large

F63-11020

3

7

Roller Bushing

F63-11026

33

8


F63-14002

25

9

Gear Worm Wheel

F63-11025

1

10

Gear A

0.8” D-cut

F63-11022

14

11

Gear C

1.5” D-cut

F63-11024

1

12

Gear B

1.5” Idle

F63-11023

7

13

Roller Rubber

F63-13001

8

14

Roller PVC

F63-13002

4

15

Roller Phenol

F63-13003

2

16

Air Pipe for Dryer

F63-13019

4

17

Film Guide of Crossover

F63-11031

1

-

-

47


Technical Support


5. Location of Main Drive Shaft Components

No

Part Name

Part No.

Quantity

1

Sprocket of Main Drive Shaft

F63-14007B

1

2

Main Drive Shaft

F63-12001

1

3

Bracket of Min Drive Shaft

F63-11005

3

4

Gear Worm Wheel

F63-11025

3

5

Worm

F63-11006

3

6

Locker of DEV, FIX, WASH-racks

F63-13022

3

7

Bushing

F63-11026

3

-

-

48


Technical Support Part VI

- Electrical Schematic

Electrical schematics

Block-Diagram of Electrical Electrical Circuit Block-Diagram Block-Diagram

Electric Power -Voltage Checking (for AC Line)

-

-

49


Technical Support


2. Schematic Circuit Diagram

-

-

50


Technical Support


3. Microprocessor sequence table

  

      

    

      

  

  

  

  

  

  

       

 

        



      

 

 





   

  



   



    



  

 



 

   

 

        

 

  

-

-

51


Technical Support


                                     “

        

               

         ’   

            

    

         

                  “        ”             

          

                                      “     ”                             

                                                                                    

    

                … …

        ……           ……         

 

  –            

                    

  

          

    

-

-

52


Technical Support PART VII

- Parts List

JP-33 Parts List JP-33 Parts List for Assembly Section Issued: Jan. 01. 2005.

No

New P/N

1 2 3 4 5 6

F63-00001 F63-11001 F63-43002 F63-13018 F63-11004 F63-14004A F63-43004C

6 7

F63-00002 F63-11002 F63-43004

Description

Q'ty

Specification

Top Cover Assembly 1 1 1 1 3 1

HIPS 401AF, Grey color 10t 15 x 380, with Glue Tape Acryl w/silk print HIPS 401AF with Blue Painting SUS316 Rubber Sponge 20 x 30 x 5t

Bottom Base Rubber Sponge for Main-body Shield

1 1

HIPS 401AF, Grey color Rubber Sponge 10 x 380 x 5t

F63-11009 F63-12029C F63-14011F F63-12029B F63-14011F F63-14011A F63-12029D F63-14011A F63-12023 F63-14022 F63-14014

Bottom Nipple Assembly Nipple In A Large type Nipple of Tank Outlet DEV,FIX,WASH DEV,FIX,WASH Hose Band φ19.5, Ear Clamp Nipple of Tank Inlet T type (DEV, FIX) Hose Band φ19.5, Ear Clamp Hose Band φ12.8, Ear Clamp Nipple of Tank Inlet (WASH) Hose Band φ12.8, Ear Clamp Nipple of O/F (Water, DEV, Fix) O-ring A out φ26.5, in φ20 x 2.0t O-ring C φ24 x 2.4t

9 3 3 2 2 2 1 1 3 6 9

HIPS 401AF, Grey color SUS316 φ25 x 20, w/ Pipe φ16 SUS 316 SUS316 φ25 x 20, w/ Pipe φ16, φ8 SUS 316 SUS316 SUS316 φ25 x 20, with pipe φ8 SUS316 SUS316 φ30 x 50 EPDM rubber EPDM rubber

19 20 21

F63-12051 F63-12052 F63-12055

Supporting Bracket Assembly Bracket of Protect Torsion (L) Bracket of Protect Torsion (S) Bracket of WASH Rack Mounting

1 1 1

PVC 10 x 10 x 70 PVC 10 x 10 x 70 ABS 15 x 50 x 100

22 23 24 25 26 27 28

F63-00007 F63-11005 F63-12001 F63-11006 F63-14010 F63-14007B F63-14006 F63-14004D

Main Shaft Assembly Bracket of Main shaft Shaft A for Motor drive Warm Spring pin for Warm Sprocket B (inside hole Φ8) Wrench Bolt Hex M4 x 8 Screw PH Tapping 4 x 12

3 1 3 3 1 1 6

PBT Black SUS316 φ8 x 407 PBT Black SUS316 φ2.0 x 20 Type No.25 Tooth 19, M4 x 2 SUS316 SUS316

29 30 31 32 33 34

F63-00008 F63-21021 F63-12037 F63-43010 F63-22022 F63-22010 F63-14003

1 1 1 2 2 1

LDW-1002, Seo-Il Elec. ABS 30 x 30 x 10t Epoxy, Araldite 5minute Rapid UL, 3pie x 15 Teflon 0.26pie x 150, White SUS316

35

F63-23003

Film Sensor Limit Assembly Reed Switch for Film Sensor Limit Bracket of Film Sensor Limit Epoxy Glue Heat Tube Wire 0.26 white for Reed Switch Screw PH M3 x 12 Wiring Flexible wire w/Connector

1

14wires x 800 w/ Connectors

8 9 10 11 12 13 14 15 16 17 18

Top Cover Cushion Sponge for Top-Cover Shield LCD Window with Glue Button of Control Screw PH Tapping 3 x 10 Rubber Sponge of Door shield

Bottom Base Assembly

-

-53


36 37

38 39 40 41 42

43 44 45 46 47

48 49 50

51 52 53 54 55 56 57 58 59

60 61 62 63

64 65 66 67 68 69 70 71

F63-22010B F63-14017

Wire 1.25 White for Film Sensor Cable Mounted

2 1

Teflon φ1.25, UL ABS UL

F63-23001 F63-11013 F63-14004E F63-11014 F63-14004E

Main PCB Assembly Main PCB Assembly Case of Main PCB Screw PH Tapping 4 x 16 Cover of Main PCB Case Screw PH Tapping 4 x 16

1 1 2 1 2

PCB Parts List (ver. 5.0) HIPS 401AF, Grey color SUS316 HIPS 401AF, Grey color SUS316

F63-21016 F63-14004E F63-12044 F63-14004F F63-14004E

Terminal Block Assembly Terminal Block Screw PH Tapping 4 x 16 Cover of Terminal Block Screw PH M5 x 10 Screw PH Tapping 4 x 16

1 2 1 3 1

250VA 20A KH-6020 10P SUS316 PE Sheet 200 x 200 x 1.5t SUS316 SUS316

F63-32003A F63-14009B F63-43030

Drain Valve Assembly Drain Valve (Lab Cock Type) Hose φ12 x 200, 2m 2m (D (DEV,FIX,WASH) Cable Ties 140mm Black

3 3

Plastic φ10 x 3/8" Red-DEV,Blue-FIX,Cl ,Clean-WASH PVC UL

F63-11008 F63-11010 F63-11012 F63-14015 F63-14016 F63-14017 F63-12033A F63-12033C F63-14011A

Front Nipple Assembly Nipple Out B Small type Nipple In B Small type Nipple Nut B Small type O-ring D φ13 x 2.6t O-ring E φ15.5 x 2.4t Cable Mounted for Dummy Cover Nipple L type of Drain DEV,FIX,WASH DEV,FIX,WASH Nut of Front Nipple L Type Hose Band φ12.8, Ear Clamp

3 3 3 3 6 3 3 3 3

HIPS 401AF, Grey color HIPS 401AF, Grey color HIPS 401AF, Grey color EPDM rubber EPDM rubber ABS UL SUS316 φ16.5 x 40 PVC φ16.5 SUS316

F63-21005 F63-14004D F63-22004 F63-22013

RPL Pump Assembly RPL Pump for DEV, FIX Screw PH Tapping 4 x 12 Terminal of "O" type Wire 1.25 Green for RPL-Pump RPL-Pump Wiring

2 4 2 1

Iwaki KBR-3XBU3M SUS316 O type w/Insulation Cap Teflon 1.25pie, UL

F63-21010 F63-14018 F63-12025 F63-13014 F63-14004D F63-14004F F63-14011A F63-22012

Solenoid Valve Assembly Solenoid Valve for Water Nipple Φ12 "I" Type for Solenoid Nipple for Wash in-let Bracket for Solenoid Screw PH Tapping 4 x 12 Screw PH M5 x 10 Hose Band φ12.8, Ear Clamp Wire 1.25 Blue for Sol-Valve Wiring

1 1 1 1 8 2 1 1

110volt-Siebe, 220volt-PAKER 220volt-PAKER Bronze 220volt only SUS316 φ26 x 55 220volt only SUS316 SUS316 SUS316 Teflon 1.25pie, UL

2 2 4 4 2

Iwaki MD-10 SUS316 SUS 316 ABS 20 x 20 x 5t ABS φ20 x 50

1

Teflon φ1 x 450, Black

72 73 74 75 76

F63-21009 F63-14004E F63-14011F F63-12049 F63-12048

77

F63-22009

Circulation Pump Assembly Circulation Pump Screw PH Tapping 4 x 16 Hose Band φ19.5, Ear Clamp Spacer of CIR pump Bracket of CIR Hose Wring Wire 1.25 Violet for Level Sensor

-

-54

SUS316 1.6t 200 x 40,


F63-22015 F63-22011

Wire Yellow for Dry Heater Wiring Wire Green/Yellow for Ground

1 1

Teflon φ1.25, UL Teflon φ1.25, UL

F63-21002 F63-14004E F63-21003 F63-14004E F63-13007 F63-14003D F63-14004D F63-22018

Blower Fan Assembly Blower Fan Screw PH Tapping 4 x 16 Capacitor for Blower Fan Screw PH Tapping 4 x 16 Bracket for Blower Fan Screw PH M4 x 8 Screw PH Tapping 4 x 12 Wire 1.25 Brown for Blow-Fan Wiring

1 2 1 1 1 2 2 1

ebm G2E 108-AA 01-01 SUS316 450VA 1.5uF SUS316 SUS316 1.6t 72 X 90 SUS316 SUS316 Teflon 1.25pie, UL

F63-21001 F63-14004E F63-21001A F63-13006 F63-14004 F63-14007A F63-14006 F63-14008 F63-13006A F63-22016

Main Motor Assembly Main Motor w/ Capacitor Screw PH Tapping 4 x 16 Reducer for 60Hz Only Bracket of main motor Screw PH Tapping 4 x 20 Sprocket A (inside hole Φ10) Wrench Bolt Hex M4 x 8 Chain of Min motor Spacer of main motor bracket Wire 1.25 Orange for Main-Motor

1 1 1 1 4 1 1 1 4 1

15W 70 X 70 with Capacitor 1.2uF SUS316 STD 25:1, VS.18:1, 50Hz 18:1 SUS316 2.0t 100 x 150 SUS316 Type No.25 Tooth 19, Tapping M4 SUS316 Type No.25/ Length 271.5mm/ 42P SUS316 φ8 x 5.5t Teflon 1.25pie, UL

F63-21013 F63-21014 F63-21015 F63-22017 F63-22006

Switch of Main power Assembly Switch of Main power Fuse Holder Fuse Wire 1.25 Black for AC in-put Wiring Terminal of Clip Type Large

1 2 2 1 3

16A250V ACT125 250V 20A FEU 0031-1673 250V 8A, DIA 6.3 x 32mm Teflon 1.25pie, UL Terminal w/ insulation Tube

102 103

F63-11015 F63-32005

Bracket of Foot Bolt Assembly Bracket of Foot Bolt Foot Bolt

4 4

HIPS 401AF, Grey color w/Tap M12 X 40L w/Rubber foot

104 105 106 107 108 109 110 111 112 113 114

F63-00009 F63-21006 F63-21022 F63-12008 F63-12057 F63-12058 F63-12009 F63-13009 F63-14004E F63-43006 F63-14011A F63-22014

1 1 1 1 1 1 2 2 1 4 1

220V 900W with Thermostat 65N PW-65N SUS316 Pipe φ8 x 200 SUS316 Pipe φ8 x 50 with Tap M8 SUS316 Pipe φ8 x 40 with Tap M8 SUS 304 φ20 x100 with φ8 hole x2 SUS316 1.0t 40 x 140 SUS316 DC HCC 435 SUS 316 Teflon 1.25pie, UL

115 116 117 118 119

F63-00010 F63-21007 F63-12010 F63-43001 F63-43005 F63-14011A

1 1 1 1 2

PT-100 SUS316 Pipe φ8 x 70 10t 100 x 100 Sealing Tape SUS 316

120

F63-12015

2

SUS316 Pipe φ8 x 80,φ12 X 40

78 79

80 81 82 83 84 85 86 87

88 89 90 91 92 93 94 95 tp 96

97 98 99 100 101

Heater of DEV Assembly Heater of DEV, with Thermostat Thermostat Extra (DEV Heater Outer) Pipe for FIX Heating Pipe for DEV heating (L) Pipe for DEV heating (S) Stainless core (for Temp. Exchange)

Bracket for DEV Heater Screw PH Tapping 4 x 16 Silicon Compound for Heat-sink Hose Band φ12.8, Ear Clamp Wire 1.25 Red for DEV-Heater DEV-Heater Wiring DEV Sensor Assembly Sensor of DEV Temp. Pipe of DEV Sensor Sponge for DEV Sensor Teflon Tape for DEV Sensor Hose Band φ12.8, Ear Clamp Plumbing Nipple "T" for RPL coupling(DEV, FIX)

-

-55


F63-14011A F63-14011F

Hose Band φ12.8, Ear Clamp Hose Band φ19.5, Ear Clamp

4 2

SUS316 SUS 316

123 124 125 126

F63-21017 F63-13023 F63-14004D F63-13020

Power Cord Assembly Power cord w/Bushing Bracket of AC Cord Screw PH Tapping 4 x 12 Bracket for Main Body

1 1 2 1

AC250V 16A H05VV-F SUS316 1.5t 30 x 80 SUS316 SUS316 2.0t 30 x 380

127 128 129 130 131 132 133 134

F63-00011 F63-21012 F63-13011 F63-12026 F63-13011B F63-13012 F63-14004D F63-22008 F63-12019

Dry Heater Assembly Heater of Dry Case for Dry Heater Ground Pin for Dry ESD Net for Dry Heater case Bracket for Dry Heater Screw PH Tapping 4 x 12 Wire-Connection for Dry Heater Insulator for Dry Heater coil

1 1 1 1 1 6 2 1

1.0Kw w/thermostat, thermo-fuse SUS316 1.6t 85 x 340, 120 x 110 SUS 316 φ1.0 x 100 SUS316 Net Mash SUS316 1.6t 90 x 90 SUS316 UL, Yellow Cap Insulator Mica 1.0t 80 x 160 Dry Heater

135 136 137

F63-00012 F63-21011 F63-13010 F63-13004D

Sensor of Water level Assembly Sensor of Water level Bracket for Level Sensor Screw PH Tapping 4 x 12

1 1 1

Material PVC, DLF-103 SUS316 20 x 80 with painting SUS316

138 F63-11003 139 F63-12004 140 F63-12017 141 F63-23002 142 F63-14004C 143 F63-14004A 144 F63-14017 145 F63-43019 146 F63-12059 147 F63-12060

Control PCB Assembly Case of Control PCB Cover of Control PCB Stud of Control Cover PCB Assembly for Control Screw PH Tapping 4 x 10 Screw PH Tapping 3 x 10 Mount of Cable Rubber Sheet of Control Cover Bracket of Rubber Holder Plate of Control Case Inner

1 1 4 1 3 2 1 1 2 1

HIPS 401AF, Grey color ABS, Natural Acetyl φ5 x 10 PCB Assembly Parts List SUS316 SUS316 PVC w/  Tape Silicon Rubber ABS 2t x 5 x 50 PE Sheet 1.5t x 50 x 50

148 F63-12031 149 F63-12032 150 F63-14005B 151 F63-14004E

Rack Lock Assembly Locker of Rack Space of Rack Locker Plate Washer φ4 Screw PH Tapping 4 x 16

3 3 3 3

Plastic SUS316 φ6.1 x 7.1t SUS316 SUS316

152 153 154

F63-12021 F63-12011 F63-14004C

Drain Filter Assembly Cover Plate of Tank Inlet Hole Screw PH Tapping 4 x 10

3 3 6

SUS Bracket 2pcs w/ SUS Net ABS 3.0t 56 x 100 SUS316 Rack Locker Hole

Door Assembly

155 156 157 158 159 160 161 162 163 164

F63-00003 F63-11016 F63-11017 F63-11018 F63-11019 F63-12006 F63-12006B F63-12007 F63-14004B F63-43004C F63-12028

1 1 1 1 1 1 2 7 1 1

HIPS 401AF, Grey color HIPS 401AF, Grey color HIPS 401AF, Grey color HIPS 401AF with Blue painting SUS316 φ6 x 27.8 SUS316 φ6 x 27.8 Pipe SUS316 φ4 x 27.8 SUS316 5t 10 x 380 SUS316 361 x 30 x 13 x 1.0t

121 122

Door-Top Door-Bottom Door Hinge Door Decoration Hinge pin A (large) of Door Hinge Pipe (large) of Door Hinge pin B (small) of Door Screw PH Tapping 3 x 12 Rubber Sponge of Door shield Bracket of Door Shield -

-56


165 166

F63-43002B F63-43002C

Cushion Sponge of Top Inside Shield Cushion Sponge of Bottom Shield

1 2

Sponge 5 x 380 x 10t Sponge 10 x 120 x 10t

167 168 169 170 171 172 173 174

F63-00013 F63-21021 F63-12034 F63-23004 F63-12035 F63-12036 F63-43010 F63-22022 F63-22010

Film Sensor Assembly Reed Switch for Film Sensor Bracket of Film Sensor (Reed Switch) Magnetic for Sensor Rod Rod of Magnetic Pin of Magnetic Rod Epoxy Glue Heat Tube Wire 0.26 white for Reed Switch

2 2 2 2 2 1 4

LDW-1002, Seo-Il Elec. ABS 30 x 50 x 5t CYL 5pie x 3t SUS316 φ5 x 20 SUS316 φ1 x 30 Epoxy, Araldite 5minute Rapid UL, φ3 x 15 Teflon φ0.26 x 150, White

175 176 177 178 179 180

F63-00014 F63-21020 F63-12038 F63-43010 F63-22022 F63-22009 F63-22010

Pilot Indicator Assembly LED for Film Loading Pilot Lens of LED Epoxy Glue Heat Tube Wire 1.25 Violet for Level Sensor Wire 0.26 white for Reed Switch

2 2 1 4 2 2

Red Color, Long-Wave, φ3 Acryl Clean 10 x 10 x 10 Epoxy, Araldite 5minute Rapid UL, φ3 x 15 Teflon φ1 x 450, Black Teflon φ0.26 x 150, White

181 182

F63-23004 F63-23004A

Magnetic for Film Sensor Limit Sub Magnetic for Film Sensor Limit

1 1

CYL 5pie x 3t Square 2 x 6 x 10

183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202

F63-00004 F63-11027A F63-11027B F63-11020 F63-11021 F63-12003 F63-14003 F63-14005 F63-12002 F63-13001 F63-12005A F63-11026 F63-13004A F63-13004B F63-14004A F63-11025 F63-11022 F63-11023 F63-11024 F63-14001 F63-14002

203 204 205 206 207 208 209 210 211

F63-00005 F63-11028A F63-11028B F63-11020 F63-11021 F63-11031 F63-12003 F63-12003B F63-14003 F63-14005

Rack Assembly DEV rack assembly Rack side plate of DEV L Rack side plate of DEV R Film Guide A Large Film Guide B Small Shaft C for Film Guide, Spacer Screw PH M3 x 12 Spring washer M3 Shaft B for Rack Drive Roller-Rubber Stud for Idle Gear and rack mounting Bushing of Roller Spring A (in Large type) Spring C (out Large type) Screw PH Tapping 3 x 10 Gear worm Wheel Gear A of 0.8" D-cut Gear B of 1.5" Idle Gear-C of 1.5" D-cut Snap Ring type "C" Snap Ring type "E"

1 1 1 4 8 16 16 1 8 2 19 4 4 8 1 8 2 1 3 12

ABS w/glass 15%, Red color ABS w/glass 15%, Red color ABS Natural, Clean color ABS Natural, Clean color SUS316 φ6 x 376 SUS316 SUS316 SUS316 φ8 x 471.2 SUS316 w/Rubber SUS316 φ8 x 33.5 PBT Black SUS316 0.6t 20 x 65 SUS316 0.6t 20 x 65 SUS316 PBT Black PBT Black PBT Black PBT Black SUS316 φ7 SUS316 φ7

1 1 1 3 4 7 2 18 18

ABS w/glass 15%, Blue color ABS w/glass 15%, Blue color ABS Natural, Clean color ABS Natural, Clean color F62-5902 common SUS316 φ6 x 376 SUS316 φ6 x 375 SUS316 SUS316

FIX rack assembly Rack side plate FIX L Rack side plate FIX R Film Guide A Large Film Guide B Small Film Guide C for Fix, Wash Crossover

Shaft C for Film Guide, Spacer Shaft D for Film Guide C Screw PH M3 x 12 Spring washer M3 -

-57


212 F63-14005B 213 F63-12002 214 F63-13001 215 F63-13002 216 F63-12005A 217 F63-11026 218 F63-13004A 219 F63-13004B 220 F63-14004A 221 F63-11025 222 F63-11022 223 F63-11023 224 F63-11024 225 F63-14001 226 F63-14002

227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257

F63-00006 F63-11029A F63-11029B F63-11020 F63-11021 F63-11031 F63-12003 F63-12003B F63-14003 F63-14005 F63-14005B F63-12002 F63-13001 F63-13002 F63-13003 F63-12005 F63-12005A F63-11026 F63-13004A F63-13004B F63-13005A F63-13005B F63-11025 F63-11022 F63-11023 F63-11024 F63-14001 F63-14002 F63-13019 F63-11030 F63-12013 F63-12014 F63-13021

258 259 260

F63-14009A F63-14009B F63-14009C

261 F63-11026 262 F63-11022

Plate Washer φ4 Shaft B for Rack Drive Roller-Rubber Roller-PVC Stud for Idle Gear and rack mounting Bushing of Roller Spring A (in Large type) Spring C (out Large type) Screw PH Tapping 3 x 10 Gear worm Wheel Gear A of 0.8" D-cut Gear B of 1.5" Idle Gear-C of 1.5" D-cut Snap Ring type "C" Snap Ring type "E"

8 1 5 3 2 19 4 4 8 1 8 2 1 2 12

SUS316 SUS316 φ8 x 471.2 SUS316 w/Rubber SUS316 w/PVC SUS316 φ8 x 33.5 PBT Black SUS316 0.5t 20 x 65 SUS316 0.5t 20 x 65 SUS316 PBT Black PBT Black PBT Black PBT Black SUS316 φ7 SUS316 φ7

1 1 3 2 4 8 2 24 12 8 1 8 4 2 6 2 31 2 2 10 10 1 14 7 1 8 18 4 2 1 1 1

ABS w/glass 15%, Black color ABS w/glass 15%, Black color ABS Natural, Clean color ABS Natural, Clean color F62-5902, common SUS316 φ6 x 376 SUS316 φ6 x 375 SUS316 SUS316 SUS316 SUS316 φ8 x 471.2 SUS316 w/Rubber SUS316 w/PVC SUS316 w/Phenol SUS316 φ8 x 26 SUS316 φ8 x 33.5 PBT Black SUS316 0.5t 20 x 65 SUS316 0.5t 20 x 65 SUS316 0.5t 20 x 45 SUS316 0.5t 20 x 45 PBT Black PBT Black PBT Black PBT Black SUS316 φ7 SUS316 φ7 ABS Molding, Grey Color PBT Black Plastic SUS316 1.6t 376 x 80 Plastic 1.6t 376 x 115 Plastic 0.6t 376 x 210

Wash rack assembly Rack side plate Wash L Rack side plate Wash R Film Guide A Large Film Guide B Small Film Guide C for Fix, Wash Crossover

Shaft C for Film Guide, Spacer Shaft D for Film Guide C Screw PH M3 x 12 Spring washer M3 Plate Washer φ4 Shaft B for Rack Drive Roller-rubber Roller-PVC Roller-phenol Stud for Idle Gear Stud for Idle Gear and rack mounting Bushing of Roller Spring A (in Large type) Spring C (out Large type) Spring B (in Small type) Spring D (out Small type) Gear worm Wheel Gear A of 0.8" D-cut Gear B of 1.5" Idle Gear-C of 1.5" D-cut Snap Ring type "C" Snap Ring type "E" Air pipe for Dryer Pusher dry roller Inner cover A for Dryer Inner cover B for Dryer Inner Case of Dryer

1 1 1

Hoses Diameter-In Diameter-In φ8.0 Hoses Diameter-In Diameter-In φ12.0 Hoses Diameter-In Diameter-In φ16.0 Spare Parts Pack in Beaker Bushing of Roller Gear A of 0.8" D-cut

-

Silicon Red, Blue, Clean Silicon Red, Blue Silicon Red, Blue, Clean

5 2 -58

PBT Black PBT Black


263 264 265 266 267 268

269 270 271 272

273 274 275 276 277 278 279 280 281 282

F63-11023 F63-11024 F63-11025 F63-14011D F63-14011E F63-14001

1 1 1 3 6 12

Gear B of 1.5" Idle Gear-C of 1.5" D-cut Gear worm Wheel Hose Band φ12.8, Worm Drive Clamp Hose Band φ22.6, Worm Drive Clamp

Snap Ring type "C"

F63-12012 F63-14009C F63-14009C F63-14021

Hoses Kit in DEV Chemical Tank RPL Pipe with Hose Red, Blue Drain Hose Red, Blue, Clean O/F Hose Red, Blue, Clean Hose Assembly for Water In-let

F63-13016 F63-12016 F63-13015 F63-12016 F63-32006 F63-43008 F63-31002 F63-12053 F63-32001 F63-32004

Accessory in FIX Chemical Tank Rack cover for DEV Handle of Rack cover Rack cover for FIX Handle of Rack cover Floater of chemical tanks Beaker I/Manual Bracket Bar for Feed-Tray Under Shield Tank of DEV, FIX RPL Stand Table w/ Foot Bolt

PBT Black PBT Black PBT Black SUS 316, for Accessory SUS 316, for Accessory SUS316 φ7

2 SUS316 φ8 x380, Hose φ8.0 x1m 3 Hose φ16 x 2meter 3 Hose φ16 x 2meter 1 Hose φ15 x 2m, Female coupling

1 1 1 1 2

PVC 2.0t 200 x400 " " Bending PVC φ10 x 15 PVC 2.0t 200 x400 " " Bending PVC φ10 x 15 Polycarbonate 150 x 380

1 Printing 1 ABS 5 x 5 x 350 2 25liter with φ8.5 Hole 1 Aluminum profile w/die-casting

Parts Balance for Optional Requirements

1 2 3 4 5 6 7

AC Voltage 110volt Requirements F63-12043 F63-12043 Bracket of 110V Sol-Valve F63-14018 Nipple Φ12 "I" Type for Solenoid F63-12025 Nipple for Wash in-let F63-13014 Bracket for Solenoid F63-14021B Hose for Water In-let 110V F63-14021 Hose Assembly for Water In-let F63-21018 SSR AC Drive Type (110volt only)

1 -1 -1 -1 1 -1 1

SUS316 60 x 60 x 2t Bronze 220volt only SUS316 φ26 x 55 220volt only

1 2 2 4 3 5 6 7 8 9

1 inch Air-Gap Requirements F63-12061 Bracket of 1" Gap Nipple F63-12062 Bracket of 1" Gap Hose F63-11007A Nipple Out A Large for 1" Gap F63-11008A Nipple Out B Small type for 1" Gap F63-11009A Nipple In A Large type for 1" Gap F63-14016 O-ring E φ15.5 x 2.4t F63-14009A Hose of 1" Air-Gap, Clean F63-11009 Nipple In A Large type F63-12011 Cover of Tank RPL Hole F63-14004C Screw PH Tapping 4 x 10

1 1 1 1 1 1 1 -1 -1 -1

ABS 2t x 20 x 20 ABS 15 x 15 x 15 HIPS 401AF, Grey color HIPS 401AF, Grey color HIPS 401AF, Grey color EPDM rubber Silicon Red, Blue, Clean HIPS 401AF, Grey color/ with Tap ABS 3.0t 56 x 100 SUS316 Rack Locker Hole Covering

1 2

Desk-Top Requirements F63-12047 Sub Bracket of Desk-Top A F63-12047B Sub Bracket of Desk-Top B

1 2 3

Main-Motor Variable Speed Requirements F63-21019 Main Motor (Variable Speed) w/ Gear, Capacitor F63-21019A Variable Speed Controller F63-21001 Main Motor w/ Capacitor

3 1

-

-59

SUS316 1.6t 200 x 40,

Hose φ15 x 2m with Female coupling Hose φ15 x 2m with Female coupling AC input to AC output, 40A rating

PVC φ30 x 40t PVC φ30 x 40t with Slot

1 15W 70 X 70 with Capacitor 1.2uF, VS Sensor 1 Rating 15watt, w/mounting bracket -1 15W 70 X 70 with Capacitor 1.2uF


1 2 3 4 5 6 7 8 9

Wash RPL Pump Type (Close Loop) F63-21005 RPL Pump for Wash F63-13024 Bracket of Water RPL F63-21010 Solenoid Valve for Water F63-14018 Nipple Φ12 "I" Type for Solenoid F63-12025 Nipple for Wash in-let F63-13014 Bracket for Solenoid F63-14004D Screw PH Tapping 4 x 12 F63-14004F Screw PH M5 x 10 F63-14011A Hose Band φ12.8, Ear Clamp

-

-60

1 1 -1 -1 -1 -1 -8 -2 -1

Iwaki KBR-3XBU3M SUS316 1.5t 80 x 150 110volt – Siebe, 220volt - PAKER Bronze 220volt only SUS316 φ26 x 55 220volt only SUS316 1.6t 200 x 40

SUS316 SUS316 SUS316

JP33 Service Manual

Recommend Documents