MEP Tower BOQ-sample

OFFICE TOWER TOWER WORKS BILL No: 1 - ELECTRICAL WORK

Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATION Supply, install, test and commissioning Transformer comply to BS171 with final termination and all r elated accessories all in accordance with the drawings and specification. Transformers A

Transformer - 1 (1.5MVA, 22KV/0.4KV)

No

B


No

C


No

D


No

E


No

F


No

G


No

H


No

Supply, install, test and commissioning of Air circuit breaker complete with all necessary supports and connections; all in accordance with the drawings and specification. Air Circuit Breaker (ACB) for Transformers J

ACB - 1

No

K

ACB - 2

No

L

ACB - 4

No

M

ACB - 5

No

N

ACB - 7

No

P

ACB - 8

No

Q

ACB - 9

No

R

ACB - 10

No

Carried to Collection

MEP Tower BOQ-sample.xls - ELECTRICAL WORK

Page 1 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Main circuits Supply, install, test and commissioning bus bars including hangers, elbows, flanges, extensions, fire barriers, flunged end etc., complete with all necessary accessories; all in accordance with drawings and specification. Bus bar system TPN cast resin insulated copper bus bar with integral earth low impedance sandwich insulated type, related supports and final termination. Busbars A

800A bus bar

m

B

1000A bus bar

m

C

1250A bus bar

m

D

2500A bus bar

m

E

Allow for third party supervision, inspection and certification of busbars including thermography scanning tests

Item

Tap off units (IP54) with final termination as per drawings and specification Tap Off Units F

100A TPN MCCB 40KA

No

G

250A TPN MCCB 40KA

No

Supply and installation of chimney for the following areas as shown on the drawings and specification. Chimney H

Pump room at 31 level

I te m

UPS Supply, install, test and commissioning UPS comply to BS5490 (IP22) complete with all supports, earth continuity strip and all related accessories; all in accordance with the drawings and specification Uninterrupted power supply J

UPS for Obstruction Obstructi on light - 10KVA

No



Page 2 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Main circuits Supply, install, test and commissioning bus bars including hangers, elbows, flanges, extensions, fire barriers, flunged end etc., complete with all necessary accessories; all in accordance with drawings and specification. Bus bar system TPN cast resin insulated copper bus bar with integral earth low impedance sandwich insulated type, related supports and final termination. Busbars A

800A bus bar

m

B

1000A bus bar

m

C

1250A bus bar

m

D

2500A bus bar

m

E

Allow for third party supervision, inspection and certification of busbars including thermography scanning tests

Item

Tap off units (IP54) with final termination as per drawings and specification Tap Off Units F

100A TPN MCCB 40KA

No

G

250A TPN MCCB 40KA

No

Supply and installation of chimney for the following areas as shown on the drawings and specification. Chimney H

Pump room at 31 level

I te m

UPS Supply, install, test and commissioning UPS comply to BS5490 (IP22) complete with all supports, earth continuity strip and all related accessories; all in accordance with the drawings and specification Uninterrupted power supply J

UPS for Obstruction Obstructi on light - 10KVA

No



Page 2 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Distribution System Supply, Supply, install, testing, commissioning of LV Main distribution board complete with circuit breakers, capacitor bank with with harmonic filtration, KWHR meter, Interlock, CT meter; all in compliance with BSEN 60 4391 Form - 4 construction as per per drawings and specification. Low Voltage Main Distribution System A

LV MSB - 7

No

B

LV MSB - 8

No

C

LV MSB - 9

No

D

LV MSB - 10

No

E

EMSB - 2

No

Supply, install, test and commissioning of sub main distribution boards comply with BS5486, complete with circuit breakers; all in accordance with the drawings and specification. Sub - Main Distribution Board F

SB-1-0-7

No

G

SB-1-0-8

No

H

SB-1-0-9

No

J

SB-1-0-10

No

K

SB-1-0-11

No

L

SB-1-0-12

No

M

SB-1-0-13

No

N

SB-1-0-14

No

P

SB-1-0-15

No

Q

SB-1-0-16

No

R

SB-1-0-17

No

S

SB-1-0-18

No



Page 3 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Distribution System (Cont'd) A

SB-2-0-19

No

B

SB-2-0-20

No

C

SB-2-0-21

No

D

SB-2-0-22

No

E

SB-2-0-23

No

F

SB-2-0-24

No

G

SB-2-0-25

No

H

SB-2-0-26

No

J

SB-2-0-27

No

K

SB-2-0-28

No

L

SB-2-0-29

No

M

SB-2-0-30

No

N

SB-7-0-31

No

P

SB-7-0-32

No

Q

SB-7-0-33

No

R

SB-7-0-34

No

S

SB-7-0-35

No

T

SB-7-0-36

No

U

SB-7-0-37

No

V

SB-7-0-38

No

W

SB-7-0-39

No

X

SB-7-0-40

No

Y

SB-7-0-41

No

Z

SB-7-0-42

No



Page 4 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED


SB-7-0-43

No

B

SB-7-0-44

No

C

SB-7-0-45

No

D

SB-7-0-46

No

E

SB-8-0-47

No

F

SB-8-0-48

No

G

SB-8-0-49

No

H

SB-8-0-50

No

J

SB-8-0-51

No

K

SB-8-0-52

No

L

SB-8-0-53

No

M

SB-8-0-54

No

N

SB-8-0-55

No

P

SB-8-0-56

No

Q

SB-8-0-57

No

R

SB-8-0-58

No

S

SB-8-0-59

No

T

ESB-31-L

No

U

ESB-31-P

No

V

ESB-1-0-31-LIFT.1

No

W

ESB-1-0-31-LIFT.2

No

X

ESB-2-0-60-LIFT.1

No

Y

ESB-2-0-60-LIFT.2

No

Z

ESB-2-0-60-LIFT.3

No



Page 5 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Distribution System (Cont'd) Supply, install, test and commissioning the distribution boards complete with circuit breakers; all in accordance with the drawings and specification. Distribution Boards A

DB-EXTERNAL -1 W/P

No

B

DB-EXTERNAL -2 W/P

No

C

DB-EXTERNAL -3 W/P

No

D

DB-EXTERNAL -4 W/P

No

E

DB-5-0-7

No

F

DB-5-0-7-EXT

No

G

DB-5-0-9

No

H

DB-5-0-9-EXT

No

J

DB-5-0-11

No

K

DB-5-0-11-EXT

No

L

DB-5-0-13

No

M

DB-5-0-13-EXT

No

N

DB-5-0-15

No

P

DB-5-0-15-EXT

No

Q

DB-5-0-17

No

R

DB-5-0-17-EXT

No

S

DB-5-0-19

No

T

DB-5-0-19-EXT

No

U

DB-5-0-21

No

V

DB-5-0-21-EXT

No



Page 6 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED


DB-5-0-23

No

B

DB-5-0-23-EXT

No

C

DB-5-0-25

No

D

DB-5-0-25-EXT

No

E

DB-5-0-27

No

F

DB-5-0-27-EXT

No

G

DB-5-0-29

No

H

DB-5-0-29-EXT

No

J

DB-7-31-1

No

K

DB-7-31-2

No

L

DB-10-0-32

No

M

DB-10-0-32-EXT

No

N

DB-10-0-34

No

P

DB-10-0-34-EXT

No

Q

DB-10-0-36

No

R

DB-10-0-36-EXT

No

S

DB-10-0-38

No

T

DB-10-0-38-EXT

No

U

DB-10-0-40

No

V

DB-10-0-40-EXT

No

W

DB-10-0-42

No

X

DB-10-0-42-EXT

No



Page 7 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED


DB-10-0-44

No

B

DB-10-0-44-EXT

No

C

DB-10-0-46

No

D

DB-10-0-46-EXT

No

E

DB-10-0-48

No

F

DB-10-0-48-EXT

No

G

DB-10-0-50

No

H

DB-10-0-50-EXT

No

J

DB-10-0-52

No

K

DB-10-0-52-EXT

No

L

DB-10-0-54

No

M

DB-10-0-54-EXT

No

N

DB-10-0-56

No

P

DB-10-0-56-EXT

No

Q

DB-10-0-58

No

R

DB-10-0-58-EXT

No

S

DB - 8-O-59 - 1

No

T

DB-8-59-KITCHEN

No

U

DB-8-59-EXT.1

No

V

DB-8-59-EXT.2

No

W

DB-10-0-60

No

X

DB-10-0-60-EXT

No



Page 8 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Distribution System (Cont'd) Supply, Install, test and commissioning the motor control center complete with circuit breakers; all in accordance with the drawings and specification. Motor Control Center A

MCP-2-0-31-FIRE PUMP

No

B

MCP-0-7-1

No

C

MCP-0-8-1

No

D

MCP-0-9-1

No

E

MCP-0-10-1

No

F

MCP-0-11-1

No

G

MCP-0-12-1

No

H

MCP-0-13-1

No

J

MCP-0-14-1

No

K

MCP-0-15-1

No

L

MCP-0-16-1

No

M

MCP-0-17-1

No

N

MCP-0-18-1

No

P

MCP-0-19-1

No

Q

MCP-0-20-1

No

R

MCP-0-21-1

No

S

MCP-0-22-1

No

T

MCP-0-23-1

No

U

MCP-0-24-1

No

V

MCP-0-25-1

No



Page 9 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED


MCP-0-26-1

No

B

MCP-0-27-1

No

C

MCP-0-28-1

No

D

MCP-0-29-1

No

E

MCP-0-30-1

No

F

MCP-0-31-1

No

G

MCP-0-31-2

No

H

MCP-0-31-3

No

J

MCC-0-31-1

No

K

MCC-0-31-2

No

L

MCC-0-31-3

No

M

MCP-0-32-1

No

N

MCP-0-33-1

No

P

MCP-0-34-1

No

Q

MCP-0-35-1

No

R

MCP-0-36-1

No

S

MCP-0-37-1

No

T

MCP-0-38-1

No

U

MCP-0-39-1

No

V

MCP-0-40-1

No

W

MCP-0-41-1

No

X

MCP-0-42-1

No

Y

MCP-0-43-1

No

Z

MCP-0-44-1

No



Page 10 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Distribution System (Cont'd) MCP-0-45-1

No

A

MCP-0-46-1

No

B

MCP-0-47-1

No

C

MCP-0-48-1

No

D

MCP-0-49-1

No

E

MCP-0-50-1

No

F

MCP-0-51-1

No

G

MCP-0-52-1

No

H

MCP-0-53-1

No

J

MCP-0-54-1

No

K

MCP-0-55-1

No

L

MCP-0-56-1

No

M

MCP-0-57-1

No

N

MCP-0-58

No

P

MCP-0-58-1

No

Q

MCP-0-58-2

No

R

MCP-0-58-3

No

S

MCC-0-58-1

No

T

MCC-0-58-2

No

U

MCC-0-58-3

No

V

MCP-0-59-1

No

W

MCP-0-60-1

No

X

Allow for miscellaneous control wiring related to other equipments / systems

Item



Page 11 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd)

Power Cable Supply, install, test and commissioning of power cable installation including lugs, glands, terminations and cable ties; all in accordance with the drawings and specification. A

4 sqmm /4C PVC/PVC+4sqmm /1C CPC

m

B


m

C

6X6 sqmm /1C PVC/PVC+6sqmm /1C CPC

m

D


m

E


m

F


m

G

25 sqmm /4C PVC/PVC + 16 sqmm/1C CPC

m

H

25 sqmm /4C XLPE/PVC+ 16sqmm /1C CPC

m

J


m

K


m

L

6X25 sqmm /1C XLPE/PVC+16sqmm /1C CPC

m

M


m

N

70 sqmm /4C XLPE/PVC+35 sqmm /1C CPC

m

P

4 x 70 sqmm /1C XLPE/PVC+ 35sqmm /1C CPC

m

Q


m

R

4 x 95 sqmm /1C XLPE/PVC+ 50 sqmm /1C CPC

m

S


m

T


m

U

4 x 120 sqmm /1C XLPE/PVC+70sqmm /1C CPC

m

V


m

W

8 x 630 sqmm/1C XLPE/PVC+2 x 300 sqmm /1C CPC

m



Page 12 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Power Cable (Fire rated ) Supply, install, test and commissioning power cables including termination to and from, glands, cable ties, lugs and related installation accessories; all in accordance with the drawings and specification. A

6 sqmm /4C Fire Rated Cable+6 sqmm /1C CPC

m

B

16 sqmm /4C Fire Rated Cable+16sqmm /1C CPC

m

C


m

D


m

E

F

G

H

J

4 x 95 sqmm /1C Fire Rated Cable+50 sqmm /1C CPC

4 x 150 sqmm/1C Fire Rated Cable+95 sqmm /1C CPC

8 x 300 sqmm/1C Fire Rated Cable+2 x 150 sqmm /1C CPC

4 x 400 sqmm /IC Fire Rated Cable+150 sqmm /1C CPC

4 x 500 sqmm/1C Fire Rated Cable+300 sqmm /1C CPC

m

m

m

m

m



Page 13 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Disconnect switches Supply, install Isolators (IP65) complete with supports, lugs and other related accessories; all in accordance with drawings and specification. Isolators A

16A, TPN Isolator

No

B

16A, TPN Isolator (Weather proof)

No

C

16A, TPN Isolator (Explosion proof)

No

Containment Supply and install GI cable tray / Ladder comply with BS4678 and complete accessoires, supports, earth continuity strip etc., all in accordance with the drawings and specification. Cable Tray D

100mm HD GI Cable Tray

m

E


m

F


m

G


m

H

600 X 100mm HD GI Cable Tray

m

J

800 X 100mm HD GI Cable Tray

m

Cable Ladder K

2 X 1000mm HD GI Cable Ladder

m

Supply and install GI conduit complete with accessoires, supports, earth continuity strip etc., all in accordance with the drawings and specification. G.I Conduit L

40mm Dia GI conduit

m

M

50mm Dia GI conduit

m



Page 14 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Small Power System Supply, install and test all associated works of power outlets comply with BS1363 including permanent wiring system and using Logic range finish to the respective system as per specification. Power outlets (Logic range) A

13A, 220V, 1 gang switched socket outlet

No

B

13A, 220V, 1 Gang switched socket outlet (W/P - IP65)

No

C

13A, 220V, 1 Gang switched socket outlet (for emergency portable lighting)

No

D

E

F

13A, 220V, 1 Gang switched socket outlet (for Hand dryer) 13A, 220V, 2 gang switched socket outlet (one gang mounted at high level / above ceiling)

No

No

15A, switched fused connection unit mounted above ceiling

No

G

20A, 3P, socket outlet

No

H

20A, 3P, socket outlet (W/P)

No

J

20A, 3P, socket outlet (explosion proof)

No

Supply, install and test all associated works of power outlets with permanent wiring system using Metal clad finish to the respective system as per drawings and specification. Power outlets (Metal clad range) K

13A, 220V, 2 Gang switched socket outlet

No



Page 15 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Lighting system Supply and install the following lighting system comply with BS88, 1273 & 1461 includes fittings, ceiling rose, heat resistant flexible cable, lamps, electronic control gear, suspension, connection to permanent wiring system; all in accordance with the drawings and specification. General Lighting A

Type F1

No

B

Type F1 (W/P)

No

C

Type F2

No

D

Type F3

No

E

Type F3 EP

No

F

Type F9 (W/P)

No

G

Type 'O'

No

H

Medium intensity red light type C high intensity white light type A

No

Medium intensity red light type C

No

J



Page 16 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Interior Decorative Lighting A

Type DL2

No

B

Type DL9

No

C

Type PR1

No

D

Type PR2

No

E

LED 1

m

F

Type COL1

m

G

Type FL14

No

H

Type FL21

No

J

Type FL28

No

K

Exit light

No

Switches Supply, install lighting switches comply to BS36376 with permanent wiring using Logic range finish to the respective lighting system as per drawings and specification. Lighting Switches (Logic range) L

10A, 1 gang, 1way DP light switch

No

M

10A, 1 gang, 1way SP light switch

No



Page 17 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Distribution System (Cont'd) Emergency Distribution System Supply, install, testing and commissioning the distribution boards complete with circuit breakers, final connection; all in accordance with the drawings and specification. Emergency Distribution Board A

EDB-1-0-7-L

No

B

EDB-1-0-8-P

No

C

EDB-1-0-9-L

No

D

EDB-1-0-10-P

No

E

EDB-1-0-11-L

No

F

EDB-1-0-12-P

No

G

EDB-1-0-13-L

No

H

EDB-1-0-14-P

No

J

EDB-1-0-15-L

No

K

EDB-1-0-16-P

No

L

EDB-1-0-17-L

No

M

EDB-1-0-18-P

No

N

EDB-1-0-19-L

No

P

EDB-1-0-20-P

No

Q

EDB-1-0-21-L

No

R

EDB-1-0-22-P

No

S

EDB-1-0-23-L

No

T

EDB-1-0-24-P

No

U

EDB-1-0-25-L

No



Page 18 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED


EDB-1-0-26-P

No

B

EDB-1-0-27-L

No

C

EDB-1-0-28-P

No

D

EDB-1-0-29-L

No

E

EDB-1-0-30-P

No

F

EDB-2-0-31-P

No

G

EDB-2-0-32-L

No

H

EDB-2-0-33-P

No

J

EDB-2-0-34-L

No

K

EDB-2-0-35-P

No

L

EDB-2-0-36-L

No

M

EDB-2-0-37-P

No

N

EDB-2-0-38-L

No

P

EDB-2-0-39-P

No

Q

EDB-2-0-40-L

No

R

EDB-2-0-41-P

No

S

EDB-2-0-42-L

No

T

EDB-2-0-43-P

No

U

EDB-2-0-44-L

No

V

EDB-2-0-45-P

No

W

EDB-2-0-46-L

No



Page 19 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED


EDB-2-0-47-P

No

B

EDB-2-0-48-L

No

C

EDB-2-0-49-P

No

D

EDB-2-0-50-L

No

E

EDB-2-0-51-P

No

F

EDB-2-0-52-L

No

G

EDB-2-0-53-P

No

H

EDB-2-0-54-L

No

J

EDB-2-0-55-P

No

K

EDB-2-0-56-L

No

L

EDB-2-0-57-P

No

M

EDB-2-0-58-L

No

N

EDB-2-0-59-P

No

P

EDB-2-0-60-L

No

Emergency lighting Supply and install the following emergency lighting system includes ceiling rose, heat resistant flexible cable, lamps, control gear, suspension, final connection , connection to permanent wiring system; all in accordance with the drawings and specification. Q

Type E1

No

R

Type E2

No

S

Type E3

No

T

Type E3 (W/P)

No

U

Type E4

No

V

Type E5

No

W

Type EB

No



Page 20 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) LOW CURRENT SYSTEM (Voice / Data system) Point wiring including permanent wiring system as per the approval from local authority; all in accordance with drawings and specification. A

Single gang RJ-45 outlet for voice

No

B

Single gang RJ-45 outlet for data

No

Accessories Supply, installation of accessories as per the drawings and specification. C

Single gang RJ-45 outlet for voive

No

D

Single gang RJ-45 outlet for data

No

Equipments Cabinet / Accessories Supply, install, test and commissioning of Telephone and data complete system provided approval from local authority; all in accordance with drawings and specification. E

Optical network unit

No

F

Fiber terminal box (FTB)

No

G

Patch panel c/w Optical converter (PP)

No

H

Patch panel - 5 pairs

No

J

Patch panel - 20 pairs

No

K

Stand alone type 19" equipment cabinet

No

L

Allow for supply and installtion of MDF, patch panels and all related cabinets, and installation accessories.

Item



Page 21 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Voice and Data System (Cont'd) Structured Cabling Supply and install structure cabling complete with all terminations; all in accordance with the drawings and specificaiton. A

B

4 x 24mm single core, 62.5um GI TIA/EIA 568-N-3 standard FIBER OPTIC cable

m

CAT6 UTP cable

m

Containment Supply and install GI cable tray complete with accessoires, supports, earth continuity strip etc., all in accordance with the drawings and specification. Cable Tray C

200mm HD G.I. cable tray

m

D

2 x 600mm HD G.I. cable tray

m

E

800mm HD G.I. cable tray

m



Page 22 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) SECURITY SYSTEM Supply, install, test and commissioning of closed circuit television system c/w permanent wiring system and other ancillaries; all in accordance with drawings and specification, but not necessarily limitted to the following; Closed Circuit Television System A

CCTV camera - Pan / Tilt / Zoom type, dome type

No

B

CCTV camera - Pan / Tilt type, dome type installation

No

C

Terminal control unit (TCU)

No

Supply, install, test and commissioning of Access & Guard tour monitoring system c/w containment, wiring and other ancillaries; all in accordance with drawings and specification. Guard Tour Monitoring System D

Guard tour (GT)

No



Page 23 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) PUBLIC ADDRESS & BACKGROUND MUSIC SYSTEM Supply, install, test and commissioning of public address & background music system c/w permanent wiring system and other ancillaries; all in accordance with drawings and specification. A

Box speaker

No

B

Box speaker (Explotion proof)

No

C

Ceiling mounted loud speaker (surface type)

No

D

Column loud speaker

No

E

Column loud speaker (W/P)

No

F

Terminal box

No

G

Overriding relay

No



Page 24 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) ANALOGUE ADDRESSIBLE FIRE ALARM SYSTEM Supply, install, test and commissioning the complete fire alarm system in compliance with BS5839 and local authorities (Abdudhabi for code and civil defence approval) including containment, cabling and other ancillaries; all in accordance with the drawings and specification. A

Addressable analogue smoke detector (concealed)

No

B

Addressable analogue duct smoke detector (concealed)

No

C

Addressable analogue heat detector with electronic sounder base (concealed).

No

D

Addressable analogue break glass unit

No

E

Addressable analogue sounder unit

No

F

Indicator lamp

No

G

Flow switch

No

H

Gas detector

No

J

Monitored stop valve

No

K

L

Addressable analogue fire alarm sub main control panel

No No

Addressable analogue annunciator panel Containment Supply and install GI cable tray complete with accessoires, supports, earth continuity strip etc., all in accordance with the drawin s and specification. Cable Tray

M

200mm GI cable tray

m

Fire Telephone Intercom System Supply, install, test and commissioning the complete fire intercom system in compliance with local authorities all including permanent wiring system and other ancillaries; all in accordance with the drawings and specification. N

Fire intercom unit with jack

No



Page 25 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) EARTHING SYSTEM Supply, install, test and commissioning and maintain complete earthing system including equipontential and supplementary bonding, complete with all tapes, test links and cross bonding conductors; all in accordance with the drawings and specification. A

1C x 70mm2 Cu/PVC earth cable

m

B

Main earth bars (30mm x 5mm)

No

C

40 x 10mm Cu Earth terminal at LV panel 7 to LV 10 & SB 2

No

D

25 x 8mm Cu Earth terminal at LV room (31st Floor)

m

E

Allow for metal projection earting including masts, aerials, air condutor units, handrails, external metallic duct works and all mechanical equipments.

Item

LIGHTNING PROTECTION SYSTEM Supply, install, test and commissioning and maintain complete lightning protection system comply with BS 6651 including equipontential and supplementary bonding, complete with all tapes, test links and cross bonding conductors; all in accordance with the drawings and specification. F

25mm x 3mm Aluminium tape on roof

m

G

Earth bonding to reinforcement

No



Page 26 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) SUNDRY / GENERAL ITEMS A

B

C

D

E

F

G

Allow for permits, fees, inspection associated with the electrical installation by utility and statutory authorities

Item

Allow for testing and commissioning and production of test certificates all in accordance with specification.

Item

Allow for all identification labels, plates, charts and identification of cable, trays, switches and the like all in accordance with specification

Item

Allow for preparing schedule of manufacturers recommended tools and spare parts for each piece of equipment.

Item

Allow for fire stopping in accordance with the drawings specification and local authorities requirements,

Item

Allow for instructing selected employer's personnel on all aspects of the operation of systems and equipment

Item

Allow for the provision of operating / maintenance manuals Item

H

J

Allow for providing shop, co-ordination and "as-built" drawings

Item

Allow for mock-up installation of Electrical accessories such as light fittings, switches, sockets etc., at Lift lobby, toilet & office area as per specification section 2 and drawings. Item

K

L

Option for contractor to provide two (2) years maintenance to all electrical systems.

Item

The contractor shall list here other items not included above but included in the Specifications and/or drawings and necessary for the complete and satisfactory completion of this section of the Works. Such items shall be deemed to be included unless specified. Item

………………………………………….



Page 27 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Collection from

Page 01 Page 02 Page 03 Page 04 Page 05 Page 06 Page 07 Page 08 Page 09 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20

AED

CARRIED FORWARD


Page 28 of 81


Project Item Ref

Item Description

Unit

Rate

Amount in AED

ELECTRICAL INSTALLATIONS (Cont'd) Collection

Brought forward Page 28 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27

AED

CARRIED TO SUMMARY


Page 29 of 81

OFFICE TOWER TOWER WORKS BILL No: 2 - MECHANICAL WORK

Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS DOMESTIC COLD WATER SYSTEM Water Meters A

Water meters for individual operation including gate valves, non return valve, union couplings including hangers, stariner, supports and accessories; all in accordance with the drawings and specification.

No

Cold Water Pipe Works Cold water pipe using polypropylene pipe works including fitting, hangers, supports and related accessories; all in accordance with the detailed drawings and specification. For raw water B

15mm Diameter

m

C

20mm Diameter

m

D

25mm Diameter

m

E

32mm Diameter

m

F

40mm Diameter

m

G

50mm Diameter

m

H

65mm Diameter

m

J

80mm Diameter

m

K

100mm Diameter

m


MEP Tower BOQ-sample.xls - MECHANICAL WORK

Page 30 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Domestic Cold Water System (Cont'd) For filtered water A

15mm Diameter

m

B

20mm Diameter

m

C

25mm Diameter

m

D

32mm Diameter

m

E

50mm Diameter

m

F

65mm Diameter

m

G

80mm Diameter

m

Cold water transfer pipe using high density polypropylene pipe works including fitting, hangers, supports and related accessories; all in accordance with the detailed drawings and specification. Cold water transfer pipe H

100mm Diameter

m

J

150mm Diameter

m

Boosted cold water supply K

40mm Diameter

m

L

50mm Diameter

m

M

65mm Diameter

m



Page 31 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Accessories / Fittings Supply, install accessories / fittings using polypropylene pipe fittings with thermal fusion joints in connection with piping; all in accordance with drawings and specificaiton. Bends A

65mm Diameter

No

B

80mm Diameter

No

C

100mm Diameter

No

D

150mm Diameter

No

Couplers (PPR) E

65mm Diameter

No

F

80mm Diameter

No

G

100mm Diameter

No

Couplers (HDPE) H

65mm Diameter

No

J

100mm Diameter

No

K

150mm Diameter

No

Pex pipe with flexible hose and other r elated accessories all in accordance with the drawings and specification. Pex pipe L

15mm Diameter

m

M

20mm Diameter

m



Page 32 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Domestic Cold Water System (Cont'd) Interior hose bib shall be brass body complete with shutt off valves in stainless steel box as per specification. Hose bib A

15mm Diameter

No

B

20mm Diameter

No

Install sanitaryware mixers complete with all related accessories and final connection, angle valve, flexible connection, support etc.; all in accordance with the drawings and specification. Sanitaryware mixers C

Wash basin mixer

No

D

Water closet hand sprayor

No

E

Urinal mixer

No

F

Kitchen sink

No

G

Janitor sink

No



Page 33 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS Valves Supply and install valves including all related accessories and supports; all in accordance with the drawings and specification. Gate valve shall be copper alloy body comply to BS5154 A

15mm Diameter

No

B

20mm Diameter

No

C

25mm Diameter

No

D

32mm Diameter

No

E

40mm Diameter

No

Gate valve shall be iron body comply to BS5154 F

50mm Diameter

No

G

65mm Diameter

No

H

80mm Diameter

No

J

100mm Diameter

No

K

150mm Diameter

No

Float valve shall be of bronze body compy to BS1212. L

80mm Diameter

No

M

100mm Diameter

No

Foot valve N

80mm Diameter

No



Page 34 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS Valves (Cont'd) Check valve shall be DZR brass body A

20mm Diameter

No

B

50mm Diameter

No

C

100mm Diameter

No

Blanked off connection with Isolating valve D

25mm Diameter

No

E

32mm Diameter

No

F

40mm Diameter

No

Pressure reducing valve station Supply and installation of pressure reducing valve station complete with all related accessories and final connection; all in accordance with the drawings and specification. For Raw water G

65mm Diameter

No

H

80mm Diameter

No

J

100mm Diameter

No

For Filter water K

25mm Diameter

No

L

32mm Diameter

No

M

50mm Diameter

No

N

65mm Diameter

No



Page 35 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS Water Storage Tank Supply, install test and commissioning multimedia water tank including water filter with water multimedia filters, activated carbon, filter AG with overflow discharge connection, drain valves, internal piping and supports all in accordance with the drawings and specification. Multimedia water filter tank A

MMF-0-31-1 & 2 (1.3 - 8.6 bars)

No

B

MMF-0-58-1 & 2 (1.3 - 8.6 bars)

No

Supply, install test and commissioning water tank using Fiber glass reinforced plastic (FRP) including overflow discharge connection, drain with valves, vent pipe and internal piping; all in accordance with the drawings and specification Insulated filter water tank C

30m3 capacity water tank

No

Raw type water tank D E

F

60m3 water tank

No

125m3 water tank (80m3 for fire & 45m3 for domestic)

240m3 water tank (150m3 for fire & 90m3 for domestic)

No

No



Page 36 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Pumps for Water Supply Installations. Pumps complete with starter control panel, wiring, connecting pipes, valves, pressure vessel, VSD, non return valves, strainer, flexible connection, pressure gauges, puddle flange, anti-vibration isolators & starters etc.; all in accordance with relevant drawings and specification. A

B

C

D

E

Domestic water transfer pump set - DTP-O-31-1 to 3 (2 duty,1 standby) pump with standard accessories 7.5l/s @ 1260kpa head

Set

Domestic water transfer pump set - DTP-O-31-4 & 5 (1 duty,1 standby) pump with standard accessories 5l/s @ 150kpa head

Set

Domestic water transfer pump set - DTP-O-58-1 & 2 (2 duty,1 standby) pump with standard accessories 5l/s @ 150kpa head each

Set

Water booster pump set- DBP-O-58-1&2 (1duty, 1standby) pump with standard accessories 1.3l/s @ 300kpa head with 1 no of hydro pnematic tank

Set

Water booster pump set- DBP-O-58-3 & 4 (1duty, 1standby) pump with standard accessories 2.8l/s @ 300kpa head with 1 no of hydro pheumatic tank.

Set

Heat exchanger pumps Supply, install, test and commissioning heat exchanger pumps with all related valves and final connection; all in accordance with the drawings and specification. F

HE-0-31-1 & 2 (4l/s @ 220Kpa)

Set

G

HE-0-58-3 & 4 (4l/s @ 220Kpa)

Set



Page 37 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) SANITARY DRAINAGE Above ground drainage pipe to uPVC pipe comply as BS5255, BS4514 and fittings including supports, brackets, hangers; all in accordance with the drawings and specification. Above Ground Pipes A

32mm Diameter

m

B

40mm Diameter

m

C

50mm Diameter

m

D

80mm Diameter

m

E

100mm Diameter

m

F

150mm Diameter

m

G

200mm Diameter

m

Kitchen waste pipe shall be cast iron hubless pipe including supports, brackets, hangers; all in accordance with the drawings and specification. H

100mm Diameter

m

J

150mm Diameter

m

Install sanitarywares complete with all related fittings, flexible and final support etc.; all in accordance with the drawings and specification. Sanitaryware Installation K

Wash basin mixer

No

L

Water closet hand sprayor

No

M

Urinal mixer

No

N

Kitchen sink

No

P

Janitor sink

No



Page 38 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fittings Supply and installation of drainage fittings using cast iron hubless including connection to pipe lines comply to CSA B70 with all related accessories; all in accordance with the drawings and specification. Bends / Elbows A

80mm Diameter

No

B

100mm Diameter

No

C

150mm Diameter

No

D

200mm Diameter

No

Tees / Reducers E

80 x 80 x 80mm

No

F

100 x 100 x 80mm

No

G

100 x 100 x 100mm

No

H

150 x 150 x 100mm

No

J

150 x 150 x 150mm

No

K

200 x 200 x 200mm

No

Reducers L

150 x 100mm

No

Couplers M

80mm Diameter

No

N

100mm Diameter

No

P

150mm Diameter

No

Q

200mm Diameter

No



Page 39 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Sanitary Drainage (Cont'd) Drainage accessories Sanitary drainage accessories complete with strainers and all related accessories; all in accordance with the drawings and specification. Floor drains are stainless steel with cover A

80mm Diameter

No

B

100mm Diameter

No

Floor traps are hopper top with heavy duty hinged stainless steel cover & frame. C

50mm Diameter

No

Velocity breaker D

80mm Diameter

No

E

100mm Diameter

No

F

150mm Diameter

No

G

200mm Diameter

No

Rodding Eye H

80mm Diameter

No

J

100mm Diameter

No

K

150mm Diameter

No

L

200mm Diameter

No

Vent cowl M

100mm Diameter

No

N

200mm Diameter

No



Page 40 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Rain Water Pipe Works Rain water pipe using Polypropylene of high density polyethylene pipe inclduing supports, brackets, hangers; all in accordance with the detailed drawings and specification. Pipe works A

50mm Diameter

m

B

100mm Diameter

m

C

150mm Diameter

m

D

200mm Diameter

m

Fittings Supply and installation of rain water pipe fittings using polypropylene pipe fitting thermal fusion joint with all related accessories; all in accordance with the drawings and specification. Bends E

100mm Diameter

No

F

150mm Diameter

No

G

200mm Diameter

No

Tees / Reducers H

100 x 100 x 50mm

No

J

150 x 150 x 50mm

No

K

150 x 150 x 150mm

No

L

200 x 200 x 50mm

No

M

200 x 200 x 100mm

No

N

200 x 200 x 200mm

No



Page 41 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Rain water pipe fittings (Cont'd) Couplers A

100mm Diameter

No

B

150mm Diameter

No

C

200mm Diameter

No

Rodding Eye D

100mm Diameter

No

E

150mm Diameter

No

F

200mm Diameter

No

Planter drain G

50mm Diameter

No

Rain water outlet / Roof drain Final connection & testing and commissioning to rain water pipe / roof drain incoordination with the rain water contractor. H

100mm Diameter

No

J

150mm Diameter

No



Page 42 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) FIRE FIGHTING SYSTEM Sprinkler Pipes Fire fighting system pipe work with hot dip galvanized steel comply to ASTM A 53 grade A & B for wet risers, sprinkler risers including Abudhabi local defence approval and civil defence approvals etc. with pipe and fittings, suitable for working pressure; all in accordance with the detailed drawings and specification. A

25mm Diameter

m

B

32mm Diameter

m

C

40mm Diameter

m

D

50mm Diameter

m

E

65mm Diameter

m

F

80mm Diameter

m

G

100mm Diameter

m

H

100mm Diameter (Drain pipe)

m

J

150mm Diameter

m

K

200mm Diameter

m

L

250mm Diameter

m



Page 43 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) Fittings Supply, install pipe fittings all in accordance with the drawings and specification Bends A

100mm Diameter

No

B

150mm Diameter

No

Tees / Reducers C

65 x 50 x 25mm

No

D

65 x 50 x 32mm

No

E

65 x 50 x 40mm

No

F

65 x 50 x 50mm

No

G

65 x 65 x 25mm

No

H

65 x 65 x 32mm

No

J

65 x 65 x 40mm

No

K

65 x 65 x 50mm

No

L

80 x 50 x 40mm

No

M

80 x 65 x 25mm

No

N

80 x 65 x 32mm

No

P

80 x 65 x 40mm

No

Q

80 x 65 x 50mm

No

R

80 x 80 x 25mm

No

S

80 x 80 x 32mm

No

T

80 x 80 x 40mm

No

U

80 x 80 x 50mm

No



Page 44 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) A

100 x 80 x 25mm

No

B

100 x 80 x 32mm

No

C

100 x 80 x 40mm

No

D

100 x 80 x 50mm

No

E

100 x 80 x 80mm

No

F

100 x 100 x 25mm

No

G

100 x 100 x 32mm

No

H

100 x 100 x 40mm

No

J

100 x 100 x 50mm

No

K

100 x 100 x 80mm

No

L

100 x 100 x 100mm

No

M

100 x 100 x 150mm

No

N

150 x 100 x 32mm

No

P

150 x 100 x 40mm

No

Q

150 x 150 x 25mm

No

R

150 x 150 x 50mm

No

S

150 x 150 x 65mm

No

T

150 x 150 x 100mm

No

U

150 x 150 x 150mm

No

V

200 x 150 x 150mm

No

W

200 x 200 x 150mm

No



Page 45 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) Sprinkler head quick response accessories Sprinkler heads shall be of NFPA 13 and UL listed A

Exposed sprinkler head

No

B

Concealed sprinkler head

No

C

Royal flush sprinkler head

No

D

Cut-off sprinkler head

No



Page 46 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) Valves and Accessories Supply, install valves and accessories with all supports, with Iron gate bronze trim, rising stem, outside and yoke and victaulic coupling etc., all in compliance with NFPA and civil defence and shall be UL listed; all in accordance with the drawings and specification. Zone control Valve A

Flow switch

No

Motorized stop valve B

150mm Diameter

No

Gate valve C

32mm Diameter

No

D

100mm Diameter

No

E

150mm Diameter

No

F

200mm Diameter

No

Automatic air relief valve G

100mm Diameter

No

H

150mm Diameter

No

J

200mm Diameter

No

Sprinkler control valve K

32mm Diameter

No

L

100mm Diameter

No

M

150mm Diameter

No

N

200mm Diameter

No

P

250mm Diameter

No



Page 47 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) Valves A

200mm Diameter (Isolating valve)

No

B

200mm Diameter (Throtting valve)

No

Strainer C

200mm Diameter

No

D

FLV

No

Supply, install pressure reducing station and accessories with all supports and PRV pressure gauge, strainer, double regulating valve etc., all in accordance with the drawings and specification. Pressure reducing station E

100mm Diameter

No

F

150mm Diameter

No



Page 48 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) Accessories A

Wet riser landing valve, 150mm Diameter

No

B

Drain off valve, 100mm Diameter

No

C

Drain off valve, 150mm Diameter

No

D

Capped for tenant fitout

No

Fire Extinguisher E

CO2 fire extinguisher capacity - 5Kg

No

F

Dry powder fire extinguisher capacity - 4Kg

No

Fire hose cabinet

Fire hose cabinet includes landing valve with PRV, 40mm Dia, 40m length hose shut-off type nozzle, set of portable dry powder and CO2 fire extinguishers, automatic hose reel with lock shield valve, PRV (typical) with stainless steel back box and architrave suitable for surface mounting; all in accordance with the drawings and specification

G

Internal fire hose cabinet

No

H

External fire hose cabinet with extinguisher

No



Page 49 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Fire Fighting System (Cont'd) Fire Pump Set Fire pump set complete with all piping, control panel inter connections, controls, emergency stop push button, and related accessories; all in accordance with NFPA standard, detailed drawings and specification. A

B

C

D

Fire electric pump (FWP-O-31-1), flow 63l/s, head 2050kpa, 2950rpm, 245KW (duty pump)

No

Fire disel pump (FWP-O-31-2), flow 63l/s, head 2050kpa, 2950rpm, (standby pump)

No

Fire Jockey pump (FWP-O-31-1), flow 1.2l/s, head 2100kpa, 1450rpm, 5.5kw.

No

Allow for other miscellaneous work in connection with other systems

Item



Page 50 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Clean Agent Fire Suppression System (FM200) Supply, Install, test and commissioning clean agent fire suppression system complete with piping, control valve, cylinders including all necessary fittings, supports, all related accessories and fixing supports in compliance with NFPA and civil defence approval; all in accordance with the detailed drawings and specification. A

LV room at 31st floor level

Item

B

Allow for other miscellaneous work in connection with other systems

Item



Page 51 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HEATING AND VENTILATION AIR CONDITIONING SYSTEM Duct Work Supply, install, test and commissioning galvanized steel (1.2mm thick) comply with DW/142 & 144 and SMACNA standard complete including supply of necessary supports, accoustic linings & tubing vanes, flexible connection, access doors and accessories; all in accordance with the drawings and specification A

Fresh air duct

m2

B

Supply air duct

m

C

Return air duct

m

D

Exhaust duct

m

E

Toilet exhaust air duct

m

F

Stair pressurization duct

m

G

Flexible duct - 250mm Dia

m

2

2

2

2

2

Supply, install non inflamable layer of fiberglass filament reinforced aluminium foil-backed blanket including all necessary fixing material; all in accordance with the drawings and specification 2

H

Fresh air duct

m

J

Supply air duct

m

K

Return air duct

m2

L

Exhaust duct

m2

M

Toilet exhaust air duct

m

N

Stair pressurization duct

m

2

2

2



Page 52 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Supply, install, test and commissioning galvanized steel (1.6mm thick) comply with DW/142 & 144 and SMACNA standard complete including supply of necessary supports, accoustic linings & tubing vanes, flexible connection, access doors and accessories; all in accordance with the drawings and specification. 2

A

Fresh air duct (fire rated)

m

B

Supply air duct (fire rated)

m

C

Smoke exhaust duct

m

D

stair case pressurization duct (fire rated)

m

E

Kitchen exhaust air duct

m

2

2

2

2

Supply, install non inflamable layer of fiberglass filament reinforced aluminium foil-backed blanket including all necessary fixing material; all in accordance with the drawings and specification. F

Fresh air duct (fire rated)

m2

G

Supply air duct (fire rated)

m2

H

Smoke exhaust duct

m2

J

stair case pressurization duct (fire rated)

m

K

Kitchen exhaust air duct

m

2

2



Page 53 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Fan coil units Supply and install, testing and commissioning of fan coil units with air vent, drain valve, test point, valves, gauges, flexible connections, motorized ON/OFF valves, thermostat, drain pan and r elated installation accessories; all in accordance with drawings and specification FCU's A

FCU-0-7 to 30-1

No

B

FCU-0-31-1

No

C

FCU-0-32 to 57-1

No

D

FCU-0-58-1

No

E

FCU-0-59-1

No

F

FCU-0-59-2

No

G

FCU-0-59-3

No

H

FCU-0-59-4

No

J

FCU-0-59-5

No

K

FCU-0-59-6

No

L

FCU-0-59-7

No

M

FCU-0-59-8

No

N

FCU-0-59-9

No

P

FCU-0-59-10

No

Q

FCU-0-59-11

No



Page 54 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Split Units Supply and install, testing and commissioning of Split units complete with outdoor units, air vent, drain valve, test point, flexible connections, thermostat, drain pan and related installation accessories; all in accordance with drawings and specification. A

IU/OU-O-31-1

No

B

IU/OU-O-31-2

No

C

IU/OU-O-31-3

No

D

IU/OU-O-60-1

No

E

IU/OU-O-60-2

No

F

IU/OU-O-60-3

No

Air handling units Supply, install, test and commissioning of Air handling units including manual air vent, test points, valves, flexible connection, motiorized modulation valve and themometer, drain pan, viberation isolator and related installation accessories; all in accordance with the drawings and specification. AHU's G

AHU-O-7 to 29-1

No

H

AHU-O-7 to 29-2

No

J

AHU-O-30-1

No

K

AHU-O-30-2

No

L

AHU-O-31-1

No

M

AHU-O-31-2

No

N

AHU-O-31-3

No

P

AHU-O-31-4

No

Q

AHU-O-31-5

No



Page 55 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Air handling units (Cont'd) A

AHU-O-31-6

No

B

AHU-O-31-7

No

C

AHU(HR)-O-31-1

No

D

AHU(HR)-O-31-2

No

E

AHU-O-32-1

No

F

AHU-O-32-2

No

G

AHU-O-33 to 56-1

No

H

AHU-O-33 to 56-2

No

J

AHU-O-57-1

No

K

AHU-O-57-2

No

L

AHU-O-58-1

No

M

AHU-O-58-2

No

N

AHU-O-58-3

No

P

AHU-O-58-4

No

Q

AHU-O-58-5

No

R

AHU(HR)-O-58-1

No

S

AHU-O-60-1

No

T

AHU-O-60-2

No

U

AHU-O-60-3

No



Page 56 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Pre-cool air handling units Supply, install, test and commissioning of pre-cool air handling units including manual air vent, test points, valves, flexible connection, motiorized modulation valve and themometer, drain pan, viberation isolator and related installation accessories; all in accordance with the drawings and specification. A

PAHU-O-31-1

No

B

PAHU-O-31-2

No

C

PAHU-O-31-3

No

D

PAHU-O-31-4

No

E

PAHU-O-31-5

No

F

PAHU-O-58-1

No

G

PAHU-O-58-2

No

H

PAHU-O-58-3

No



Page 57 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Fans Supply, install, test and commissioning fans complete with silencer, bell mouth, wire mesh; all in accordance with the drawings and specification. Extract air fan A

EAF-O-31-1

No

B

EAF-O-31-2

No

C

EAF-O-58-1

No

D

EAF-O-58-2

No

Toilet Extract fan E

TEAF-O-31-1

No

F

TEAF-O-31-2

No

G

TEAF-O-58-1

No

Supply air fan H

SAF-O-31-1

No

J

SAF-O-31-2

No

K

SAF-O-31-3

No

L

SAF-O-31-4

No

M

SAF-O-58-1

No

N

SAF-O-58-2

No

P

SAF-O-58-3

No

Q

SAF-O-58-4

No

Smoke extract fan R

SEF-O-31-1

No

S

SEF-O-31-2

No

T

SEF-O-58-1

No

U

SEF-O-58-2

No Carried to Collection


Page 58 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Stair case pressurization fan Supply, install, test and commissioning stair pressurization fan all in accordance with civil defence approval complete with silencer, bellmouth, wire mesh; all in accordance with the detailed drawings and specification. A

SPF-O-31-1

No

B

SPF-O-31-2

No

C

SPF-O-31-3

No

D

SPF-O-31-4

No

E

SPF-O-58-1

No

F

SPF-O-58-2

No

G

SPF-O-58-3

No

H

SPF-O-58-4

No

Variable air volume J

VAV-O-7 to 30-1 (250x200)

No

K

VAV-O-7 to 30-2 (300x250)

No

L

VAV-O-7 to 30-3 (350x300)

No

M

VAV-O-32 to 57-1 (250x200)

No

N

VAV-O-32 to 57-2 (300x250)

No

P

VAV-O-32 to 57-3 (350x300)

No

Q

VAV-O-58-1 (250x200)

No

R

VAV-O-58-2 (250x200)

No



Page 59 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Grills Supply and Installation of duct grills comply with BS5750 and BS476 complete with installation accessories; all in accordance with the drawings and specification. Supply grille (Double deflection) A

200 x 200mm

No

B

400 x 200mm

No

C

900 x 350mm

No

D

1000 x 500mm

No

Supply grille (Fixed blade) E

250 x 200mm

No

F

500 x 750mm

No

G

1000 x 500mm

No

H

1250 x 1750mm

No

Eggcrate grille J

125 x 125 mm

No

K

150 x 150 mm

No

L

200 x 200 mm

No

M

450 x 450 mm

No

N

1000 x 350 mm

No

P

1250 x 400 mm

No

Q

1500 x 500 mm

No

R

2400 x 900 mm

No



Page 60 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Diffuser Supply, install test and commissioning the supply and return air diffusers with dampers and of aluminium construction and related installation accessories; all in accordance with the schedule and specification.

Supply air diffuser with four way throw, square louvered A

450 x 450mm

No

1200mm length and 25mm each slot linear diffuser B

One slot diffuser

No

C

Three slot diffuser

No

Return air intake louvres D

4000 x 425mm

No

Dampers Supply, install, test and commissioning dampers consist of Galvanized steel complete with all related supports and accessories; all inaccordance with detailed drawings and specification Volume control dampers E

150 x 150mm

No

F

200 x 200mm

No

G

250 x 200 mm

No

H

300 x 300mm

No

J

500 x 500mm

No

K

500 x 750mm

No

L

1700 x 1000mm

No

M

200mm dia

No



Page 61 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Dampers Supply, install, test and commissioning dampers consist of Galvanized steel complete with all related supports and accessories; all inaccordance with detailed drawings and specification Fire dampers A

125 x 125 mm

No

B

150 x 100mm

No

C

200 x 200 mm

No

D

250 x 200 mm

No

E

300 x 250 mm

No

F

350 x 300 mm

No

G

400 x 200 mm

No

H

450 x 450mm

No

J

800 x 500 mm

No

K

1000 x 500 mm

No

L

1500 x 400 mm

No

M

1900 x 1100 mm

No

N

2000 x 1000 mm

No

P

2400 x 500 mm

No

Q

2500 x 1250 mm

No

R

2500 x 1500 mm

No



Page 62 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Motorized damper A

300 x 300 mm

No

B

500 x 500 mm

No

C

800 x 500 mm

No

D

1000 x 450 mm

No

E

1000 x 500 mm

No

F

1200 x 1000 mm

No

G

1250 x 450 mm

No

H

1500 x 400 mm

No

J

1500 x 1250 mm

No

K

1600 x 1100 mm

No

L

1700 x 1000 mm

No

M

1750 x 1250 mm

No

N

2000 x 800 mm

No

P

2000 x 1000 mm

No

Q

2400 x 500 mm

No

R

2500 x 1500 mm

No



Page 63 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Motorized fire smoke damper A

1000 x 300 mm

No

B

1100 x 900 mm

No

C

1700 x 350 mm

No

D

2000 x 800 mm

No

E

2750 x 1250 mm

No

Sound Attenuator / Silencer of stainless steel construction F

3475 x 525mm

No

Constant air volume G

Constant air volume box (1200 l/s)

No

H


No

J


No

K


No

Duct detector Supply and installation of duct smoke detectors complete with all related accessories; all in accordance with the drawings and specification L

Duct smoke detector

No



Page 64 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Chilled Water Pipe Work Supply, install, test and commissioning chilled water pipe work, schedule 40, black mild steel pipe to BS 1387 : 1985 complete with finishes, jacketing, fittings, test points, supports, hangers and related accessories; all in accordance with the drawings and specification. Piping to BS1387 steel heavy grade black, screwed threads A

25mm Diameter

m

B

32mm Diameter

m

C

40mm Diameter

m

D

50mm Diameter

m

Piping to BS1387 steel heavy grade black, welded joints, bevelled ends. E

65mm Diameter

m

F

80mm Diameter

m

G

100mm Diameter

m

H

125mm Diameter

m

J

150mm Diameter

m

K

200mm Diameter

m

L

250mm Diameter

m

M

300mm Diameter

m

N

350mm Diameter

m

P

400mm Diameter

m

Q

450mm Diameter

m



Page 65 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Chilled water pipe work insulation Supply, install, test and commissioning chilled water pipe work insulation complete with phenolic foam including finishes and fastening, vapour barriers, sheating, adhesives and related accessories; all in accordance with the drawings and specification. A

450mm Diameter

m

Fittings Supply and install chilled water pipe fittings comply with BS143 and BS1246 including flanged welded to black steel and related accessories; all in accordance with the drawings and specification. Bends B

65mm Diameter

No

C

80mm Diameter

No

D

100mm Diameter

No

E

125mm Diameter

No

F

150mm Diameter

No

G

200mm Diameter

No

H

250mm Diameter

No

J

450mm Diameter

No



Page 66 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Tee / Reducers A

80 x 80 x 65mm

No

B

80 x 80 x 50mm

No

C

100 x 65 x 65mm

No

D

125 x 80 x 65mm

No

E

125 x 80 x 100mm

No

F

150 x 150 x 65mm

No

G

150 x 80 x 80mm

No

H

150 x 150 x 65mm

No

J

100 x 80 x 50mm

No

K

100 x 100 x 40mm

No

L

100 x 100 x 80mm

No

M

150 x 150 x 25mm

No

N

150 x 150 x 40mm

No

P

150 x 150 x 50mm

No

Q

150 x 150 x 65mm

No

R

150 x 150 x 80mm

No

S

150 x 150 x 125mm

No

T

150 x 150 x 150mm

No

U

200 x 150 x 150mm

No

V

200 x 200 x 125mm

No

W

200 x 200 x 150mm

No

X

250 x 250 x 200mm

No

Y

450 x 450 x 150mm

No

Z

450 x 450 x 200mm

No



Page 67 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Reducers A

100 x 80mm

No

B

80 x 40mm

No

C

80 x 50mm

No

D

200 x 80mm

No

E

200 x 125mm

No

F

250 x 80mm

No

G

250 x 100mm

No

H

250 x 125mm

No

J

250 x 200mm

No

Coupling K

65mm dia

No

L

80mm dia

No

M

100mm dia

No

N

125mm dia

No

P

150mm dia

No

Q

200mm dia

No

R

250mm dia

No

S

300mm dia

No

T

350mm dia

No

U

400mm dia

No

V

450mm dia

No



Page 68 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Condensate drain pipe Supply and install condensate drain pipe with insulation comply with BS2871 complete with all related accessories and supports; all in accordance with the drawings and specification. Copper pipe A

15mm Diameter

m

B

25mm Diameter

m

C

32mm Diameter

m

uPVC pipe D

100mm Diameter

m

E

Allow for condensate drain insulation which necessary to prevent condensation

m

Fittings Supply and install condensate drain pipe fittings uPVC and all related accessories; all in accordance with the drawings and specification. Couplings F

100mm Diameter

No

Tee / Reducers G

100 x 100 x 25mm

No

H

100 x 100 x 32mm

No



Page 69 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Valves and Accessories Supply, install valves and accessories with all supports, fixing and fittings; all in accordance with the detailed drawings and specification. Isolating Valves shall be bronze body comply with BS 5154 A

40mm Diameter

No

Isolating Valves shall be cast iron body comply with BS5150 B

100mm Diameter

No

C

250mm Diameter

No

Automatic air vent shall be bronze type D

32mm Diameter

No

450mm Diameter at 31st floor level E

Butterfly valve

No

F

Isolating valve

No

G

Temerature gauge

No

H

Pressure gauge

No

J

Y - Strainer

No



Page 70 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Plate heat exchanger Supply, install liquid plate exchanger comply with ASHRAE, NEC standards and complete with necessary connection piping, valves, gauges, thermometers, strainers and accessories i ncluding supports, controls as per detailed drawings, schedule and specification. A

HE - O - 31 - 1 (3050KW)

No

B

HE - O - 31 - 2 (3050KW)

No

C

HE - O - 31 - 3 (3050KW)

No

D

HE - O - 31 - 4 (302KW)

No

E

HE - O - 31 - 5 (302KW)

No

F

HE - O - 58 - 1 (302KW)

No

G

HE - O - 58 - 2 (302KW)

No

Heat Recovery Pump Supply and installation of the heat recovery pumps complete with all necessary supports, compounents and accessories etc., all in accordance with the drawings and specification. H

HRP-O-31-1 of 4.5l/s @ 200kpa head

No

J


No

K


No



Page 71 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) HVAC system (Cont'd) Chilled water pumps Supply, install, test and commissioning chilled water pumps complete with control panel valves, instruments, gauges, strainers etc., all in accordance accordance with the drawings and specification. Secondary chilled water pump of 89l/s @ 350kPa head at 31st floor level A

SCHW P-O-31-1 (Duty)

No

B

SCHW P-O-31-2 (Duty)

No

C

SCHW P-O-31-3 (Standby)

No


MEP Tower BOQ-sample.xls BOQ-sample.xls - MECHANICAL WORK

Page 72 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) GAS Installation NOTE: The LPG gas distribution network including fittings and accessories shall be in accordance with standard specificaiton The contractor is to include with in his pipe work rates for pipe-fittings and for providing tee connections with a standard intervals and end caps; all in accordance with the drawings and specificaiton. Pipes & fittings Supply and installation of Copper gas pipe including supply and installation of fittings. A

100mm Diameter

m

Gate valve shall be iron body comply with BS5154 B

100mm Diameter

No

Meters C

Gas meter

No

Blanked off connection with Isolating valve D

100mm Diameter

No

Accessories / Fittings Supply and installation of accessories / fittings all in accordance witih the drawings and specification. Bends E

150mm Diameter

No

Couplers F

100mm Diameter

No



Page 73 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Building Management System Supply, install permanent wiring system complete with termination and all related accessories; all in accordance with the schedule, drawings and specification. Containment and cabling Electrical A

MSB & EMSB

No

B

SD & ESB

No

C

MCP & MCC

No

D

DB & EDB

No

Control panels E

Sub alarm panel

No

Pumps F

Transfer water pumps

No

G

Booster pump

No

H

Fire fighting pump

No

J

Chilled water pumps

No

K

Heat recovery pumps

No

L

Plate heat exchanger

No

M

Water tank

No

N

Cold water meter

No

P

Gas system meter

No



Page 74 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Building Management System (Cont'd) HVAC system A

Exhaust air fan

No

B

Toilet extract fans

No

C

Supply air fans

No

D

Smoke extract fans

No

E

Constant volume box

No

F

Staircase pressurization fans

No

G

Variable air volume units

No

H

AHU's

No

J

PAHU's

No

K

FCU's

No



Page 75 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Building Management System (cont'd) Supply, install accessories as per the BMS point schedule complete with testing and commissioning of the system and all related accessories; all in accordance with the drawings and specification. Accessories / Equipments Electrical A

MSB & EMSB

No

B

SD & ESB

No

C

MCP & MCC

No

D

DB & EDB

No

Control panels E

Sub alarm panel

No

Pumps F

Transfer water pumps

No

G

Booster pump

No

H

Fire fighting pump

No

J

Chilled water pumps

No

K

Heat recovery pumps

No

L

Plate heat exchanger

No

M

Water tank

No

N

Cold water meter

No

P

Gas system meter

No



Page 76 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Building Management System (Cont'd) HVAC system A

Exhaust air fan

No

B

Toilet extract fans

No

C

Supply air fans

No

D

Smoke extract fans

No

E

Constant volume box

No

F

Staircase pressurization fans

No

G

Variable air volume units

No

H

AHU's

No

J

PAHU's

No

K

FCU's

No

HVAC system Equipments L

Remote programmable unit

M

Allow for soft ware, f ield sensors, actuators, net controller, Management station central equipment and all related accessories etc., all in accordance with the specification and drawings.

No

Item



Page 77 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) SUNDRY / GENERAL ITEMS A

B

C

D

E

F

G

H

J

K

Allow for permits, fees, inspection associated with the electrical installation by utility and statutory authorities

Item

Allow for testing and commissioning and production of third party test certificates

Item

Allow for all identification labels, plates, charts and identification of plant, equipment, pipes and the like all in accordance with specification

Item

Allow for preparing schedule of manufacturers recommended tools and spare parts for each piece of equipment.

Item

Allow for fire stopping in accordance with the drawings specification and local authorities requirements,

Item

Allow for instructing selected employer's personnel on all aspects of the operation of systems and equipment

Item

Allow for the provision of operating / maintenance manuals

Item

Allow for providing shop, co-ordination and "as-built" drawings

Item

Option for contractor to provide two (2) years maintenance to all electrical systems.

Item

The contractor shall list here other items not included above but included in the Specifications and/or drawings and necessary for the complete and satisfactory completion of this section of the Works. Such items shall be deemed to be included unless specified.

Item

………………………………………….



Page 78 of 81

AED


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Collection

Page 01 Page 02 Page 03 Page 04 Page 05 Page 06 Page 07 Page 08 Page 09 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25

AED

CARRIED FORWARD


Page 79 of 81


Project Item Ref

Item Description

Unit

Rate

Amount in AED

MECHANICAL INSTALLATIONS (Cont'd) Collection

Brought forward Page 50 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48 Page 49

AED

CARRIED TO SUMMARY


Page 80 of 81

MEP Tower BOQ-sample

Recommend Documents