TMDXSCBP6618X - Small Cell Base Station Platform Quick Start Guide DIP SW S4
DIP SW S1
DIP SW S3
JTAG Connector
Future Use AIF2 SFP-2 USB JTAG AIF2 SFP-1 Debug LEDs
FPGA LED 2 TCI6618 FPGA LED 1
DIP SW S2
C6A8167 Debug Ethernet UART Cable Jack
Backhaul Ethernet
LED 2
LED 3
LED 1
Reset Button Power DIN
J24 Connector
An ideal Partner in Your Growth w
w
w
.
a
z
c
o
m
.
i
t
The TMDXSCBP6618X includes:
TMDXSCBP6618X Power supply Power cord & Universal Adapter (USA, UK, Europe) Mini B USB cable for on-board JTAG emulation Ethernet cable UART cable (Audio Jack to DB-9) Documentation
Before starting: • • •
1
Check integrity of the packaging Open the package and check that all the parts listed above are present and undamaged Execute the steps described below
Set DIP SWITCH S1 in order to select USB JTAG or 20 pin connector JTAG (switch position 9) and if JTAG must be connected to TMX320C6A8167 or TMX320TCI6618X (switch position 2). The board supports only one JTAG chain at a time.
Switch S1: TMX320TCI6618X - USB JTAG
Switch S1: TMX320TCI6618X - 20 pin connector JTAG
Switch S1: TMX320C6A8167 - USB JTAG
Switch S1: TMX320C6A8167 - 20 pin connector JTAG
TMDXSCBP6618X
Quick Start Guide
2
Set DIP SWITCH S2 and S3 as shown in the figures below. TMX320C6A8167 will boot from NAND flash. For TMX320TCI6618X both configurations are described (“No boot” and “Network boot”).
Switch S2: NAND Boot (TMX320C6A8167)
3
Switch S3: No boot (TMX320TCI6618X)
Switch S3: Network boot (TMX320TCI6618X)
Set DIP SWITCH S4 as shown in the figure below to set standard JTAG mode. Other configurations are reserved for future use. If necessary, select endianness with a jumper on J24 connector, position 5-6 (close: BIG ENDIAN, open: LITTLE ENDIAN)
Switch S4: Standard JTAG
TMDXSCBP6618X
Connector J24: Endianess
Quick Start Guide
4 5 6 7
Connect the UART cable to the UART cable jack for console monitoring.
Connect the MINI-USB cable or 20-pin JTAG connector (as selected in Step 1) for on board embedded emulation.
Connect your PC (or Ethernet switch/router) to the Gigabit Ethernet port (RJ1) using the supplied Ethernet cable.
Connect the 12V DC power supply to power jack (J1). Warning: Power ON and Power OFF procedures require disconnection of Switching Power Supply. In order to reduce mechanical stress of the DIN connector J1, please leave it plugged together. To turn off the power, unplug the power cord from the Switching Power Supply (or disconnect the plug from the socket).
TMDXSCBP6618X
Quick Start Guide
Getting Started When the TMDXSCBP6618X is powered, it executes some procedures to load FPGA and check hardware functionalities. Looking at the LEDs during start-up phase you can verify that the start-up procedure is successfully completed. -
LED 1 (GREEN): this is the Power LED. When Power Supply is connected this LED must be switched ON.
-
LED 2 (RED): this LED blinks during board start-up phase, then it is turned OFF.
-
LED 3 (GREEN): this LED is turned ON after FPGA start-up phase completion. It shows that board is up and running.
-
Diagnostic LEDs: these LEDs are turned ON during start-up phase. They must be OFF after start-up completion.
-
FPGA LED 1: this LED (RED) blinks during FPGA programming phase, then it’s turned OFF if FPGA is successfully loaded.
-
FPGA LED 2: this LED (GREEN) shows FPGA status. It is turned ON after FPGA is successfully loaded.
TMDXSCBP6618X
Quick Start Guide
After this phase, TMX320C6A8167 Reset Code is executed by the Bootloader and the LINUX is loaded. If you are connected with the console cable, you can monitor software initialization. U-Boot 2010.06 (May 13 2011 - 21:23:58) TI8168-GP rev 1.0 ARM clk: 987MHz DDR clk: 398MHz DRAM: 2 GiB NAND: HW ECC Hamming Code selected 256 MiB
###### ## ## ## ###### ## ## ## ######
###### ## ## ## ## ## ## ## ######
######## ## ## ## ## ######## ## ## ## ## ########
######## ## ## ## ## ######## ## ## ##
Net: Detected MACID:64:7b:d4:6c:ca:9e Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 1 0 NAND read: device 0 offset 0x280000, size 0x440000 Skipping bad block 0x004a0000 4456448 bytes read: OK ## Booting kernel from Legacy Image at 81000000 ... Image Name: Arago/2.6.37-r0/tmdxscbp6618x Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1964096 Bytes = 1.9 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK
At the end of the procedure, Linux prompt should be available. Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.37 (a0875269@gtrgwdeb) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 Fri May 13 20:50:35 EDT 2011 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: tmdxscbp6618x bootconsole [earlycon0] enabled reserved size = 0 at 0 Memory policy: ECC disabled, Data cache writeback. . . . INIT: Entering runlevel: 5 Starting Starting Starting Starting
system message bus: dbus. telnet daemon. syslogd/klogd: done thttpd.
_____ | _ |___ ___ ___ ___ | | _| .'| . | . | |__|__|_| |__,|_ |___| |___|
_____ _ _ | _ |___ ___ |_|___ ___| |_ | __| _| . | | | -_| _| _| |__| |_| |___|_| |___|___|_| |___|
Arago Project http://arago-project.org tmdxscbp6618x ttyO0 Arago 2011.02 tmdxscbp6618x ttyO0 tmdxscbp6618x login:
TMDXSCBP6618X
Quick Start Guide
Online Documentation Most of the documentation on TMDXSCBP6618X is available online at the following link: http://www.azcom.it
Select Support menu and then TMDXSCBP6618X item.
TMDXSCBP6618X Information The link contains: -
User Guide Hardware details FPGA downloads TMX320TCI6618X & TMX320C6A8167 datasheets Frequently Asked Questions (FAQ)
Azcom Technology Address Azcom Technology s.r.l. Centro Direzionale Milanofiori Strada 6 - Palazzo N2 20089 Rozzano (MI) - Italy Tel. +39-02.82450311 Fax: +39 02 57512632 Web: www.azcom.it e-mail:
[email protected]
TMDXSCBP6618X
Quick Start Guide