User Manual for UV210C

Shenzhen Multi Co.,limited

www.multiflatbedprinter.com

[email protected]

The User Manual for A4 UV flatbed

Printer

Model:UV210C Thanks for purchasing our our A4 UV flatbed printer

UV210C.This user manual manual will guide you how to use it. Please

make sure you read and full understand this manual before your installation and using. Please keep this manual well for your reference in emergency. emergency.

Index Chapter 1 The package List Chapter 2 The A4 LED UV printer introduction Chapter 3 The preparation work before opening the machine Chapter 4 The preparation work before printing Chapter Chapte r 5 The detail Process Process of printing printing object object Chapter 6 The note matters and trouble shooting Chapter 7 The machine warranty Chapter 8 The machine specification

Chapter 1 Package List Please open the packing cases after receiving machine, clean up the protective film, check the machine whether there is any damage, and make an inventory according to the following packing list .

1. One unit A4 UV Printer 2 One CD of the printer driver (we can sent by email also) 3. The softdog ( the white USB key) for Acro RIP software 4. 6 pcs empty UV ink bottle and one waste ink bottle 5.The USB cable 6.The power line 7. The operation manual which will be sent via email 8.Other spare parts,such as sensor, syringes . (Please keep it for future using.)



[email protected]

Chapter 2 the A4 UV Flatbed Printer Introduction This machine is modified with EPSON L800/R330 print head, please use the EPSON L800/R330 printer driver and the compatible consumables. For the detailed specification, please refer to the printer’s instructions.

The front of the printer

The back of the printer

The control panel



[email protected]

Note: 1.Please put the uv bottles on the bottle bracket or same height place . 2.Please open the

printer cover

when you use the printer.Please close the uv window when

you ship the printer.

The spare parts introduction as following.



[email protected]

Chapter 3 The preparation work before Opening the machine 3.1 Add the water into the water cooling pump There is two solutions for installation the water cooling pump .Please check it as following. 3.1.1.Solution one is very easy,please check it following.

Open this cover

Put the water cooling pump like this and add the water into the tank about 90% fully water. When the light lamp on, please check whether there is water circulation. please check. It is very important . there should be water circulation when the led lamp work.

3.1.2.Solution two is a little complicated

,please check it following.

Open the cover

Take out the foam



[email protected]

Take out the water tank

Open the cover of the tank

Add the water into the tank about 90% fully

Closed the cover and cross placed it to ensure it does not leak the water

Take the tank back again and pay attention to the water in the tube whether is circulating when the machine carry out the printing task.



[email protected]

Notes : 1.Due to it is first time to use the printer, please check whether

there is water circulation when the machine

carry out the printing task . Please check following for checking whether there is water circulation. A. you can touch the water tube and feel the water is moving B. The indicator light will be on during the UV lamp is working

The indicator light will be on when the LED lamp is working

2. Please add the water when there is not enough water

in the water tank .

3.2. Install the CISS ( Damper ) For making your installation easier, we have install the damper for you ,what you need to do is insert the pipe into the ink bottles.

This is ink sac CISS

T

Insert the ink sac into the nozzle corresponding with the color label in the head cartridges one by one



[email protected]

Adjust the tube distance to ensure the print head can move back and forth smoothly

Please insert each pipeline to the corresponding ink bottle according to the label of the pipeline

Finish its installation. Please put the UV ink bottles onto the UV ink bottle bracket on the side of the printer and insert the waste ink pipe into waste ink bottle .

Notes: 1. Please feed the different color uv ink corresponding the color bottle . 2. Since uv white ink is very easy blocked,so please shake the white ink bottle everyday before using. 3. If you do not use the uv printer more than one week, please use the cleaning linquid to cleaning the printhead . 4. You can use both Y,K,M,C,LM,LC and Y,K,M,C,W,W ink type. If you use Y,K,M,C,W,W ink type, please put the W,W into the LM, LC place.

Chapter 4 The preparation work before printing 4.1 The machine self-checking The control panel is on the front of the machine .The power jacket is on the back of the machine . Please refer to following pictures .



[email protected]

Please pull the platform to the front position completely , then open the general power of the machine ,and then open the power of the printer , the printer will be in self-checking process. When do self-checking process, the printer power button will be green flash, print head

will move right and left .After self-checking ,the printer power button will keep in

long green light state . When the printer power button is in long green light state , the machine is in normal state (Sometimes if both the ink button and paper button is flash , please do not worry.It is normal situation .please close the power of printer and open the power again ) The

process of open the machine as following.

The platform will stay in

Open the power of the

the front completely

machine

Open the power of the printer, the printer will do the self-checking ,the indicator will green flash . After finishing self-checking, the indicator will be long green light state.

Note: Please do machine self-checking before it start working every day .

4.2 Install the printer driver Put the CD driver on the computer, and install it according to the hints. Use USB cable to c onnect computer and printer, the computer will identify the printer automatically. The computer will install the printer driver automatically and prompt "new hardware is ready to use"; at this time, the printer driver is installed well . If the computer can not install the driver automatically , please install the driver which will match with your computer system bit .

such as your computer is Win7 32 bit system , then you will chose the driver which compatible with Win7 32

if not , the driver won’t install it successfully .

Note: if the printer driver that we give that you can’t be installed successfully, you can to download it from epson website:www..epson.com or you contact us freely.

4.3 Fill ink into machine When use the printer in the first time, we need to do print head ink transmit .There is two methods .Please check it as following. 4.3.1 Method One : do power cleaning for head ink transmit as following. Open printer in your computer. Press CTRL+P to choose

Epson L800 printer click attribute ,choose

Maintenance in attribute . Click Print head cleaning ,Choose

，

power cleaning

in Maintenance



[email protected]

Click head cleaning

Choose

“

Power

cleaning ” Click Start

Do the print head cleaning 1-2 times , the ink will be sucked to tube automatically

When do the head cleaning, the ink flow into the tube quickly as well as observe whether it has waste ink flow into the waste ink bottle .

After the progress bar is refilled the full color , the head cleaning task finished

，

Note : The printer should be done the

power cleaning only under the following situation :

A. The first time to fill the ink for the machine , you can do the power cleaning for tube quickly. B. When the print head clog seriously , you can do the power cleaning .

making the ink flow into the print head and



[email protected]

4.3.2 Method two : print head ink transmitting from the waste ink pipe. Generally speaking , when you finished the print head cleaning , the ink will flow into the print head completely . If not ,you can try the following method to transmit ink into the print head easily. 1. Transmit the ink by syringe without needle as following.

1.take out the waste ink pipe from the waste ink bottle .

2.use syringe to suction ink from the waste ink pipe .when there is around 30ml ink in the syringe ,please put the waste ink pipe back to waste ink bottle .

2.After suction ink with syringe, we should do head cleaning 1-2 times to feed the print head with ink.

4.3.3 Method three: print head ink transmitting from ink sac. Generally speaking , when you finished the power cleaning , the ink will flow into the ink sac completely . If not ,you can try the following method to transmit ink into the ink sac easily .Before doing method two,please make sure the following. A、If the printer is already turn on, please turn off the power switch firstly. B、Turn on the total power when the print head cartridge don’t move. C、Turn off the total power immediately while the print head cartridge move out from the side. . D、 At this time, the print head cartridge is not lock, you can easily move it back and forth by hand Now let’s start method two as following. 1、Transmit the ink by hand with syringe as following.

Ink sac is inserted on the shower of the head, draw it up ,you can take it out.

Use syringe to suction ink as picture, the ink sac is full when you can see the ink in syringe , then insert the ink sac back



[email protected]

2.after suction ink to the ink sac, we should do head cleaning 1- 2 times to feed the print head with ink.

4.4 Do the nozzle checking We should print the nozzle check page to test whether the machine is ok. 1 ) Put one piece A4 paper on the right and front position of the platform , adjust the height of the platform by the knob, then push the platform to the rear position. Notes: 1.please make sure the printed product on the platform is very nearly to the “limit board”, around 2mm ,which means just can pass it,don’t let the printed product

touch the limit board.

2.Please make sure the platform is located in the rear position before printing .Tthe Platform work from behind, it will stop in the front position after finish printing. 2 ) Press CTRL+P to choose click print

Epson L800 printer click attribute ,choose Maintenance in attribute . Click Nozzle check and ，

in Maintenance

Click Nozzle Check

Click Print

3) To compare the printed nozzle checking line and the nozzle line in your computer as following picture Print the nozzle checking line, if every color line is complete, that means you can print the picture normally.

If the nozzle checking lines have broken line, please check the CISS whether it is installed correctly ,to check each color tube whether pump the full ink ,to check whether it has too much air in the tube ,after that , do the print head cleaning again until the line can print completely .

Note:

When the machine can be used normally, but there is broken nozzle checking line, please do the “ head


cleaning”,


[email protected]

do not need to use “ power cleaning “ to clean it .

Chapter 5 The detail process of the media printing via RIP software The Acro RIP software is convenient to adjust the printing position as well as it can adjust its printing ink volume according with customer’s request. It is very simply operation. The RIP is included by two parts, one is RIP driver (CD), the other is software dog(USB) . Due to this software is a direct drive and modify printer system core program, some security software and anti-virus software w ill protect the core program of software make the software can not be installed , so we need turn off the safety procedures and anti-virus program before installing the software .This Acro RIP 8.2 can be used for in windows XP, 2000,vista and windows 7, windows8,windows 10. Following it is the process of operation. Step1. Install the driver of the RIP software

(It will have the driver for RIP in our CD or we can send its driver via email )

we can give you one video reference

Step2 after finishing the installation, you can see two icons

.

Please kindly differ these two icons as following.

is used for light color product printing with M,Y,K,C,LM,LC ink type..

is used for dark color product printing with M,Y,K,C,W,W ink type..

Step3. Insert the RIP software dog

Following we will use

,then open the icon

for details setting.

or

in your desktop .

or



[email protected]

Step 4 Click file and then choice open to put the picture to the RIP software,and click the icon

in

,appear following.

“Printer”choose

EPSON

Stylus

Photo

R290

Service choose the L800 printer which is being used now, and the status display "printer ready" “ink resolution” should be set more than 1440* 1440 DPI If bidirectional printing is blurry, you can change to Unidirection Check Paper size : OFF “Port”

Other items please follow the left icon set, please pay attention to the red circle

Step5

Click the icon in the right of bottom

, click

, it will display following:

INK Chnnel: If there is white ink in the CISS, or there just have Y M C K, no other inks, you must choose the color pattern for “Y K W W M C” “ Ink Limit ” is allowed to adjust by yourself ,usually 50% is the same effect as without software If you find the print design of a single color slants deep or shallow, you can set up in a single color area

Step6 Click the icon in the right of botton

,click



[email protected] “Paper Size”mean the printer size , please set as

the red circle “Output Position” refers to the print position that the material printed on the platform, please remember the width and height of printing ,we will make this as origin of c oordinates

refers to the output frame size of the “Output Size” photo, we can make the input size big when printing the location map , so that we can fix the materials vertical “Copies”can be set according to your needing Scale：TUR Ｅ mean you can adjust the picture by its true scale, the picture is harmonious, if you choose FALSE, you can change the width and the height by yourself, but the picture will broaden and lengthen

Following is we

Take 5S Phone case as one example Output Position X (Width) it will be always 3 Y (Height) it will be always 2 (The number will be always keep the same with the number when you print the border line Output Position: 5S width will be 6 and the height is 12.6

Step 7 Because there is a distance between the UV light and the print head, the movement scope of the print head working is limited to whole printed scope .This will cause the images between this distance can not be UV light irradiation ,Which means can not be curing . So we must artificially expand the scope of print head movement .We need draw a vertical bar near the picture left side 3cm, do as the following picture (the operating sequence from 1 to 7)



[email protected]

,click

Step 8 : Click the icon in the right of bottom

White Layer Generation , pls choose it according with your request View the white layer , the picture will black during the area which will print the white ink

Step 9 : After the picture setup well, adjust the height of the platform ( it will be the suitable height which the platform does not touch the limited bar , keep about 2MM during the print head and platform ) , then pull the platform to the rear of the machine completely Step 10:

picture

After above steps finished , pls click icon

,click

,

it will show following



[email protected]

After the pop-up printing box, if you print dark material, please set print number 1 in “White Setting” set print number 0 in “Color Setting” ,then click , after finished 1 time white ink print, you can do the same settings if you want to print 2 time white ink

Step 11:

after white ink task finished, you can print color ink ,as followings

After the white ink task finished, you can do color ink print. please set print number 0 in” White Setting”, and set print number 1 in “Color Setting”, then , click if you print light material, please skip to step 4 and 5, directly to step 6 operation

Step 12 After click the print in the computer , the print head will start to print and the platform will move to front automatically , the power of the printer button will green and flash , finished the printing task , the platform will stop in the front completely , the power of printer will be keep green light .

Note:if you want to print emboss effect picture, you can set the parameter as following suggest : smooth effect,no striping on the picture ： DPI 2880*1440,ink amount 40% ， color is a litter light smooth effect,a little striping on the picture DPI is 2880*1440 ink amount 50% ， color is good smooth effect, no striping on the picture DPI 2880*2880 ,ink amount 50%，color is good

Note: High DPI, print picture is more good, less striping. High DPI need increase the ink amount. If customer need the whole picture print white ink uniform, you can set a pure color picture . Hollowed-out picture can realize the emboss effect more easily than the full color picture .



[email protected]

Chapter 6 Notable Matters and Common Problems 1.UV printer can print almost everything except T-shirt,you need do pre-coating first when print glass,metal etc. 2.After the machine use a while, you find the picture is not good, please print nozzle check and do head cleaning. 3.Ink bottle must on the position we appointed .too high or low position is not good ,it Will cause high pressure. the level of the ink must lower than the print head,otherwise the ink will leak out from the print head. the waste ink bottle should be checked at fixed period . 4.Special attention matters when printing A.Make sure the platform is located in the rear position before printing each time , let the machine be ready for printing. B.When the platform is in using process, do not drag, otherwise, it will can't normally print. C.The printer finish printing when there is no printing , t hen you can take out the material D.Make sure the flat surface of the print tray don’t touch the “Limit board” 5.Every time we only can release one print command, if the machine don’t print correctly, you need to cancel the print task and release the new print command. 6.Adjust the height of the platform. Different material has different thickness, we should adjust the height of the platform via the height adjustment knob.The best print quality is that the distance between the material and the head is 2mm, must avoid too high, otherwise it will damage print head ,not less than 3mm,too low position will affect the

image. We had helped you do the limited board before we send the

cargo out. It is the best height to be printed objects from the nozzle, when the print tray just can pass the limit board 7.You had better add sewing machine oil on the track that the print head move back and forth, in order to reduce resistance,otherwise it will happen flash red when start the machine ; What’s more,we should add oil on the track that the print tray go through, if the track resistance is big,the tray will not move, it will affect the print precision too. 8.Because the white ink is easy to precipitate, it is best for customer to shake the white ink for several minutes before using the machine everyday.If you don’t use the machine for a long time ,please shake the white ink for several minutes and suction the white ink from the ink sac again(the way please see “Suction Ink”),the ink that suction out can put back into the bottle and continue use,after suction the ink ,you should do head cleaning again. 9.The UV ink will curing when come across the UV- light, so please don’t lay the machine on the place where can be shined . 10.Attention of choosing picture. A.No matter the pictures from the Internet or the customer offer, you must determine the clarity of the picture,poor clarity will cause poor print quality. Generally speaking, we should provide more than 300dpi to get good quality . B.When we need to print pictures, it is best for us to design the picture the same size as material printed by PhotoShop (or AI), please don’t directly modify the size in the AcroRIP, otherwise the picture will widen or lengthen, the picture will be disproportionately. C.disproportionately you can study the PS on networkStudy website:http://www.duote.com/tech/photoshop/ NOTE: you just need do the strong cleaning in the following cases: 1).you can do strong cleaning when first time to use the machine , so that you can suction the ink to the pipe and print Head fast. 2).when the print head is a little clogging,you can do strong cleaning.



[email protected]

11.Check the water cooling pump regularly: UV LED is cooled by the water,please check whether there is

water is full every

month. 12.Ink reset . when the Ink light keep flash and computer reminds that there will be no ink,we need do ink reset.Please kindly note it is no relation with the actual ink amount, just have relation with chip count capacity,We can do ink reset when the Ink light flash advanced, also can do it when the light in long red state .All types of printer need to do ink reset on the market, it is not the machine’s problem, please don’t worry.Please use the ink reset software for ink reset. 13.Waste ink reset. when the Ink light and paper light flash one after one. we need do waste ink reset by software.

Chapter 7 The Machine warranty and specification 1. Due to the machine in the application must use a special ink, for print head only guarantee good condition When buying,After using the ink ,the nozzle blocking, pumps and accessories get corrosive , or the main board burned when cleaning nozzle in a wrong way, they are not within the scope of free warranty. 2.We provide one year warranty for all the electronic parts including the main board, driver board, control board, motor, etc. (Except for the man-made factors) But there is no warranty for wearing parts like ink pump, print head, and CISS since they are consumables. 3.After receiving the goods ,please read the user manual carefully ( so that you are familiar with the

product parts name ) then

we can communicate more easily when you come across problems. 4.If you do not know some details or you have some problems, please contact with us in time , do not dismantle the machine by yourself . if you dismantle it before contact with us , you will bear the risk of dismantle the machine.

Chapter 8 The machine specification Specification Printer Printing Technology Minimum drops:

quantity

6-color advanced MicroPiezo inkjet technology of

1.5 picoliter of 90 / per color inkjet hole slightly * 6 = 540 color spray holes

Print Resolution

User definable Up to 5760 x 1440 dpi

Print size

User definable up to A4: 21*30cm ，with led on :16*30cm

Print Speed Print Height Height adjustment

55 seconds/A4 of full-color photo 0-7.5cm Via one knob to adjustment

Warranty

Basically 1 year, extendable, see terms and condition of sales

Printer certification

CE ,FCC,RoHS certification

INK AND MEDIA Ink Type

Y/K/LC/LM/M/C (it just can print light materials when all the ink is color) Y/K/W/W/M/C (it can print light and dark materials when there have white ink)

Ink Consumption

15 ml per SQM printed area

Printing software

RIP software, Photoshop,Core1DARW,Illustrator

Automatic nozzle cleaning method Printer consumable

using computer automatic cleaning function "printer properties maintenance - nozzle cleaning" UV ink



[email protected]

PRINTER CONNECTIVITY Power supply Interface

AC220/110 v + 10, 50 hz ~ 60 hz,100W USB universal serial bus (USB) Hi-speed USB2.0

cooling system

Water cooling

Operating Systems

Windows® 2000, XP, Windows Vista™, Win7 ,Win8 7Macintosh® OS X 10.2.8, 10.3.9, 10.4.11, 10.5.x and 10.6.x

Operating Temperature

0 ° to 35 ° (50 ° to 95 ° F)

Operating Humidity

20% to 80%

WEIGHTS, DIMONSION Printer Dimensions Package dimensions Package include

60*46*35cm,30kgs 78*57*45cm ,38kgs ,wooden case Printer ,Driver CD ,USB cable, power cable,instructions

User Manual for UV210C

Recommend Documents