ASTM Plastics Standards - 2014/08/21 Designation Analytical Methods D494 - 11 D792 - 13 D1505 - 10 D1601 - 12 D1603 - 12 D1895 - 96(2010)e1 D1921 - 12 D2124 - 99(2011) D2238 - 92(2012)e1 D2857 - 95(2007) D3016 - 97(2010) D3124 - 98(2011) D3465 - 14 D3591 - 97(2011) D3594 - 93(2013) D3749 - 13 D4001 - 13 D4094 - 07 D4218 - 96(2008) D4275 - 09 D4443 - 13 D4526 - 12 D4603 - 03(2011)e1 D4754 - 11 D4883 - 08 D5017 - 96(2009)e1 D5225 - 14
D5226 - 98(2010)e1 D5227 - 13 D5296 - 11 D5477 - 11 D5507 - 99(2012) D5508 - 94a(2009)e1 D5576 - 00(2013) D5594 - 98(2012) D5630 - 13 D6042 - 09 D6247 - 10 D6248 - 98(2012)e1 D6474 - 12 D6645 - 01(2010) D6869 - 03(2011) D6953 - 11 D6980 - 12 D7083 - 04(2010)e1 D7132 - 14 D7134 - 05(2012) D7191 - 10 D7210 - 13 D7399 - 08 D7486 - 08(2013)e1 D7567 - 09 D7823 - 13
Cellular Materials - Plastics and Elastomers D1056 - 14 D1621 - 10 D1622 / D1622M - 14 D1623 - 09
D1667 - 05(2011) D1786 - 10 D2126 - 09 D2842 - 12 D3453 - 12 D3489 - 11 D3574 - 11 D3575 - 14 D3576 - 04(2010) D3676 - 13 D3748 - 14 D3768 - 11 D3769 - 10 D3851 - 07(2012) D4273 - 11 D4274 - 11 D4659 - 14 D4660 - 12 D4661 - 13 D4662 - 08(2011)e1 D4663 - 10 D4669 - 07(2013)e1 D4670 - 07(2012)e1 D4671 - 05(2010)e1 D4672 - 12 D4819 - 13 D4875 - 11 D4877 - 10 D4878 - 08 D4889 - 04(2011) D4890 - 13 D5155 - 10 D5523 - 10
D5629 - 11 D5672 - 09 D6099 - 13 D6226 - 10 D6342 - 12 D6437 - 05(2010)e1 D6576 - 13 D6979 - 13 D7133 - 11 D7252 - 06(2011)e1 D7253 - 06(2011)e1 D7487 - 13
Durability of Plastics D543 - 06 D570 - 98(2010)e1 D618 - 13 D1042 - 12 D1435 - 13 D1499 - 13 D1712 - 09(2014) D2565 - 99(2008) D3045 - 92(2010) D4329 - 13 D4364 - 13 D4459 - 12 D4674 - 02a(2010) D5870 - 11 D6360 - 07
Environmentally Degradable Plastics and Biobased Products
D3826 - 98(2013) D5071 - 06(2013) D5208 - 14 D5210 - 92(2007) D5272 - 08(2013) D5338 - 11 D5511 - 12 D5526 - 12 D5988 - 12 D6340 - 98(2007) D6400 - 12 D6691 - 09 D6866 - 12 D6868 - 11 D6954 - 04(2013) D7026 - 13 D7444 - 11 D7473 - 12 D7475 - 11
Executive D4968 - 09
Film, Sheeting, and Molded Products C1147 - 14 D882 - 12 D1004 - 13 D1204 - 14 D1239 - 14 D1593 - 13 D1709 - 09
D1894 - 14 D1922 - 09 D1938 - 08 D1998 - 13 D2103 - 10 D2463 - 10b D2561 - 12 D2578 - 09 D2582 - 09 D2659 - 11 D2673 - 09 D2684 - 10 D2732 - 08 D2838 - 09 D2911 - 10 D2923 - 13 D3354 - 11 D3420 - 08a D3981 - 09a D4204 - 12 D4272 - 14 D4321 - 09 D4397 - 10 D4635 - 08a D4801 - 08 D5047 - 09 D5419 - 09 D5946 - 09 D6287 - 09 D6988 - 13 D7192 - 10 D7310 - 11
Government/Industry Standardization D3892 - 93(2009) D4000 - 13 D5740 - 11 D6436 - 14
Mechanical Properties D256 - 10 D638 - 10 D695 - 10 D732 - 10 D747 - 10 D785 - 08 D790 - 10 D952 - 10 D953 - 10 D1043 - 10 D1044 - 13 D1708 - 13 D1822 - 13 D2583 - 13a D2990 - 09 D3763 - 10e1 D4065 - 12 D4092 - 07(2013) D4093 - 95(2010) D4440 - 08 D4473 - 08 D4508 - 10 D4812 - 11 D5023 - 07
D5024 - 07 D5026 - 06 D5045 - 99(2007)e1 D5083 - 10 D5279 - 13 D5418 - 07 D5420 - 10 D5592 - 94(2010) D5628 - 10 D5947 - 11 D6068 - 10 D6110 - 10 D6272 - 10 D6395 - 11 D7027 - 13 D7107 - 04(2010) D7774 - 12 D7791 - 12
Optical P roperties D542 - 14 D1003 - 13 D1746 - 09 D2457 - 13 D6290 - 13
Plastic Building Products D1494 - 12 D3678 - 97(2008)e1 D3679 - 13 D3841 - 97(2008)e1
D4068 - 09 D4226 - 11 D4477 - 09 D4495 - 12 D4551 - 12 D4726 - 09 D4756 - 13 D4803 - 10 D5206 - 13 D5319 - 12 D5926 - 11 D6777 - 02(2010)e1 D6864 - 11 D7082 - 04(2010) D7251 - 11 D7254 - 07 D7445 - 09 D7793 - 13 D7856 - 14
Plastic Lumber D6108 - 13 D6109 - 13 D6111 - 13a D6112 - 13 D6117 - 13e1 D6341 - 14 D6662 - 13 D7258 - 14 D7568 - 13
Recycled Plastics
D5577 - 94(2010)e1 D5814 - 10 D5991 - 09 D6265 - 09 D6288 - 09 D7209 - 06 D7611 / D7611M - 13
Reinforced Plastic Piping Systems and Chemical Equipment C581 - 03(2008)e1 C582 - 09 D2105 - 01(2014) D2143 - 00(2010) D2310 - 06(2012) D2517 - 06(2011) D2924 - 12 D2925 - 01(2007)e1 D2992 - 12 D2996 - 01(2007)e1 D2997 - 01(2007)e1 D3262 - 11 D3299 - 10 D3517 - 14 D3567 - 97(2011) D3681 - 12e1 D3753 - 12e1 D3754 - 14 D3839 - 14 D3840 - 14 D3982 - 08(2014) D4024 - 12
D4097 - 01(2010) D4161 - 14 D4167 - 97(2007) D4398 - 07 D5364 - 08e1 D5365 - 12 D5421 - 05(2010) D5677 - 05(2010) D5685 - 11 D5813 - 04(2012) D6041 - 11 D6783 - 05(2011)
Reinforced Thermosetting Plastics D2291 - 09 D2343 - 09 D2562 - 94(2008) D2563 - 08 D2584 - 11 D2734 - 09 D3647 - 09 D3846 - 08 D3914 - 02(2008) D3916 - 08 D3917 - 12 D3918 - 11 D4385 - 13 D4475 - 02(2008) D4476 / D4476M - 14 D5028 - 09 D5117 - 09 D7029 - 09
D7745 - 11
Specimen Preparation D955 - 08(2014) D957 - 12 D1896 / D1896M - 10 D3419 - 12 D3641 - 14 D4703 - 10a D5224 - 12 D6289 - 13
Terminology D883 - 12 D1600 - 14 D7711 - 11e1
Thermal Properties D635 - 10 D648 - 07 D696 - 08e1 D731 - 10 D746 - 13 D1238 - 13 D1525 - 09 D1790 - 08 D1929 - 13a D2843 - 10 D2863 - 13 D3014 - 11
D3123 - 09 D3364 - 99(2011) D3418 - 12e1 D3675 - 14 D3795 - 00a(2012) D3801 - 10 D3835 - 08 D3895 - 07 D4804 - 09 D4986 - 10 D5025 - 12 D5048 - 14 D5132 - 11 D5207 - 14 D5422 - 09 D5930 - 09 D7309 - 13
Thermoplastic Materials D706 - 09 D707 - 09 D787 - 12 D788 - 12 D789 - 07e1 D1045 - 14 D1203 - 10 D1243 - 95(2008) D1248 - 12 D1430 - 11 D1562 - 09 D1693 - 13 D1710 - 08
D1755 - 09 D1784 - 11 D1823 - 95(2009) D1824 - 95(2010) D2115 - 10 D2116 - 07(2012) D2222 - 13 D2287 - 12 D2383 - 14 D2396 - 94(2012) D2538 - 02(2010) D2581 - 09 D2647 - 10 D2765 - 11 D2839 - 10 D3012 - 13 D3030 - 11 D3159 - 10 D3222 - 05(2010) D3275 - 08(2013) D3291 - 11 D3294 - 09 D3295 - 06(2011) D3296 - 14 D3307 - 10 D3308 - 12 D3350 - 12e1 D3367 - 13 D3368 - 14 D3595 - 14 D3596 - 13 D3915 - 06 D3935 - 09
D3965 - 11 D4020 - 11 D4066 - 13 D4067 - 11 D4101 - 14 D4203 - 12 D4216 - 13 D4349 - 10 D4396 - 06 D4441 - 04(2010) D4549 - 11 D4591 - 07(2012) D4634 - 11a D4673 - 02(2008) D4745 - 11ae1 D4802 - 10 D4894 - 07(2012) D4895 - 10 D4969 - 07(2012) D4976 - 12a D5138 - 11 D5203 - 07 D5204 - 13 D5205 - 10 D5260 - 04(2010) D5336 - 09 D5436 - 13 D5491 - 08 D5492 - 10 D5575 - 07(2013) D5675 - 13 D5857 - 14 D5927 - 09
D5989 - 14a D5998 - 10 D6040 - 12 D6098 - 10 D6100 - 14 D6150 - 09 D6261 - 14 D6262 - 12 D6263 - 11 D6338 - 10 D6339 - 11 D6358 - 11 D6394 - 14 D6456 - 10 D6457 - 08(2013) D6585 - 11 D6712 - 01(2009) D6713 - 14 D6778 - 12 D6779 - 12a D6835 - 08(2014) D6865 - 11 D6867 - 03(2009) D7193 - 11 D7194 - 12 D7211 - 13 D7292 - 12 D7293 - 12 D7436 - 12 D7471 - 09(2014) D7472 - 09(2014) D7474 - 12
Thermosetting Materials D704 - 99(2012) D705 - 99(2012) D1201 - 13 D1636 - 13 D1763 - 00(2013) D3013 - 13 D4350 - 13 D5948 - 05(2012)
Title
Standard Test Method for Acetone Extraction of Phenolic Molded or Laminated Products Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement Standard Test Method for Density of Plastics by the Density-Gradient Technique Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers Standard Test Method for Carbon Black Content in Olefin Plastics Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1 Standard Practice for Dilute Solution Viscosity of Polymers Standard Practice for Use of Liquid Exclusion Chromatography Terms and Relationships Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry Standard Test Method for Purity of Monomeric Plasticizers by Gas Chromatography Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers Standard Test Method for Residual Vinyl Chloride Monomer in Poly(Vinyl Chloride) Resins by Gas Chromatographic Headspace Technique Standard Test Method for Determination of Weight-Average Molecular Weight of Polymers By Light Scattering Standard Test Method for Acid Content of Ethylene-Acrylic Acid Copolymers Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique Standard Test Method for Determination of Butylated Hydroxy Toluene (BHT) in Polymers of Ethylene and Ethylene–Vinyl Acetate (EVA) Copolymers By Gas Chromatogr Standard Test Method for Determining Residual Vinyl Chloride Monomer Content in PPB Range in Vinyl Chloride Homo- and Co-Polymers by Headspace Gas Chromatogr Standard Practice for Determination of Volatiles in Polymers by Static Headspace Gas Chromatography Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer Standard Test Method for Two-Sided Liquid Extraction of Plastic Materials Using FDA Migration Cell Standard Test Method for Density of Polyethylene by the Ultrasound Technique Standard Test Method for Determination of Linear Low Density Polyethylene (LLDPE) Composition by Carbon-13 Nuclear Magnetic Resonance Standard Test Method for Measuring Solution Viscosity of Polymers with a Differential Viscometer
Standard Practice for Dissolving Polymer Materials Standard Test Method for Measurement of Hexane Extractable Content of Polyolefins Standard Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by High Performance Size-Exclusion Chromatography Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR) Standard Test Method for Determination of Trace Organic Impurities in Monomer Grade Vinyl Chloride by Capillary Column/Multidimensional Gas Chromatography Standard Test Method for Determination of Residual Acrylonitrile Monomer in Styrene-Acrylonitrile Copolymer Resins and Nitrile-Butadiene Rubber by Headspace-Capill Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR) Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Ac etate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR) Standard Test Method for Ash Content in Plastics Standard Test Method for Determination of Phenolic Antioxidants and Erucamide Slip Additives in Polypropylene Homopolymer Formulations Using Liquid Chromatograp Standard Test Method for Determination of Elemental Content of Polyolefins by Wavelength Dispersive X-ray Fluorescence Spectrometry Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry Standard Test Method for Determining Molecular Weight Distribution and Molecular Weight Averages of Polyolefins by High Temperature Gel Permeation Chromatogra Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry Standard Test Method for Coulometric and Volumetric Determination of Moisture in Plastics Using the Karl Fischer Reaction (the Reaction of Iodine with Water) Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC) Standard Test Method for Determination of Moisture in Plastics by Loss in Weight Standard Practice for Determination of Monomeric Plasticizers in Poly (Vinyl Chloride) (PVC) by Gas Chromatography Standard Test Method for Determination of Retained Blowing Agent in Extruded Polystyrene Foam Standard Test Method for Molecular Mass Averages and Molecular Mass Distribution of Atactic Polystyrene by Matrix Assisted Laser Desorption/Ionization (MALDI)-Tim Standard Test Method for Determination of Moisture in Plastics by Relative Humidity Sensor Standard Practice for Extraction of Additives in Polyolefin Plastics Standard Test Method for Determination of the Amount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared Spectrophotometer (FTIR) Standard Test Method for Measurement of Fines and Dust Particles on Plastic Pellets by Wet Analysis Standard Test Method for Determining Gel Content in Crosslinked Ethylene Plastics Using Pressurized Liquid Extraction Standard Test Method for Determination of Low Level, Regulated Phthalates in Poly (Vinyl Chloride) Plastics by Thermal Desorption—Gas Chromatography/Mass Chroma
Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber Standard Test Method for Compressive Properties Of Rigid Cellular Plastics Standard Test Method for Apparent Density of Rigid Cellular Plastics Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics
Standard Specification for Flexible Cellular Materials - Poly (Vinyl Chloride) Foam (Closed-Cell) Standard Specification for Toluene Diisocyanate Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging Standard Test Method for Water Absorption of Rigid Cellular Plastics Standard Specification for Flexible Cellular Materials—Urethane for Furniture and Automotive Cushioning, Bedding, and Similar Applications Standard Test Methods for Microcellular Urethane Materials Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers Standard Test Method for Cell Size of Rigid Cellular Plastics Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay Standard Practice for Evaluating High-Density Rigid Cellular Plastics Standard Test Method for Microcellular Urethanes—Flexural Recovery Standard Test Method for Microcellular Urethanes--High Temperature Sag Standard Specification for Urethane Microcellular Shoe Soling Materials Standard Test Method for Polyurethane Raw Materials: Determination of Primary Hydroxyl Content of Polyether Polyols Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols Standard Test Methods for Polyurethane Raw Materials: Determination of Specific Gravity of Isocyanates Standard Test Methods for Polyurethane Raw Materials: Determination of the Isomer Content of Toluenediisocyanate Standard Test Methods for Polyurethane Raw Materials: Determination of Total Chlorine in Isocyanates Standard Test Methods for Polyurethane Raw Materials: Determination of Acid and Alkalinity Numbers of Polyols Standard Test Method for Polyurethane Raw Materials Determination of Hydrolyzable Chlorine of Isocyanates Standard Test Method for Polyurethane Raw Materials: Determination of Specific Gravity of Polyols Standard Test Method for Polyurethane Raw Materials: Determination of Suspended Matter In Polyols Standard Test Method for Polyurethane Raw Materials Determination of Unsaturation of Polyols Standard Test Method for Polyurethane Raw Materials: Determination of Water Content of Polyols Standard Specification for Flexible Cellular Materials Made From Polyolefin Plastics Standard Test Methods of Polyurethane Raw Materials: Determination of the Polymerized Ethylene Oxide Content of Polyether Polyols Standard Test Method for Polyurethane Raw Materials: Determination of APHA Color in Isocyanates Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA Color of Polyols Standard Test Methods for Polyurethane Raw Materials Determination of the Isocyanate Content of Aromatic Isocyanates Standard Test Method for Polyurethane Raw Materials Acidity by Argentometric Determination of Hydrolyzable Chlorine in Monomeric, Aromatic Isocyanates
Standard Test Method for Polyurethane Raw Materials Determination of Acidity in Low-Acidity Aromatic Isocyanates and Polyurethane Prepolymers Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm (1-in.) Deflection Technique Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Moderate to High Acidity Aromatic Isocyanates Standard Test Method for Open Cell Content of Rigid Cellular Plastics Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy Standard Test Method for Polyurethane Raw Materials: alkalinity in Low-Alkalinity Polyols (Determination of CPR values of Polyols) Standard Specification for Flexible Cellular Rubber Chemically Blown Standard Test Method for Polyurethane Raw Materials: Determination of Basicity in Polyols, Expressed as Percent Nitrogen Standard Test Method for Polyurethane Raw Materials: Instrumental Measurement of Tristimulus CIELAB Color and Yellowness Index of Liquids Standard Test Method for Polyurethane Raw Materials: Determination of Monomer and Isomers in Isocyanates Standard Test Method for Polyurethane Raw Materials: Determination of Acidity as Acid Number for Polyether Polyols Standard Practice for Polyurethane Raw Materials: Polyurethane Foam Cup Test
Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents Standard Test Method for Water Absorption of Plastics Standard Practice for Conditioning Plastics for Testing Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture Standard Practice for Outdoor Weathering of Plastics Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics Standard Practice for Resistance of Plastics to Sulfide Staining Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications Standard Practice for Heat Aging of Plastics Without Load Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to I ndoor Office Environments Standard Practice for Calculating Property Retention Index of Plastics Standard Practice for Enclosed Carbon-Arc Exposures of Plastics
Standard Practice for Determining Deg radation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus Standard Practice for Fluorescent Ultraviolet (UV) Exposure of Photodegradable Plastics Standard Test Method for Determining the Anaerobic Biodegradation of Plastic Materials in the Presence of Municipal Sewage Sludge Standard Practice for Outdoor Exposure Testing of Photodegradable Plastics Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in Soil Standard Test Methods for Determining Aerobic Biodegradation of Radiolabeled Plastic Materials in an Aqueous or Compost Environment Standard Specification for Labeling of Plastics Designed to be Aerobically Composted in Municipal or Industrial Facilities Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water I Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis Standard Specification for Labeling of End Items that Incorporate Plastics and Polymers as Coatings or Additives with Paper and Other Substrates Designed to be Aerobic Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation Standard Guide for Sampling and Reporting of Results for Determination of Biobased Content of Materials via Carbon Isotope Analysis Standard Practice for Heat and Humidity Aging of Oxidatively Degradable Plastics Standard Test Method for Weight Attrition of Plastic Materials in the Marine Environment by Open System Aquarium Incubations Standard Test Method for Determining the Aerobic Degradation and Anaerobic Biodegradation of Plastic Materials under Acc elerated Bioreactor Landfill Conditions
Standard Guide for Annual Review of Test Methods and Specifications for Plastics
Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics Standard Test Method for Tensile Properties of Thin Plastic Sheeting Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method Standard Specification for Polyethylene Upright Storage Tanks Standard Specification for Polyethylene Film and Sheeting Standard Test Method for Drop Impact Resistance of Blow-Molded Thermoplastic Containers Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting Standard Test Method for Column Crush Properties of Blown Thermoplastic Containers Standard Specification for Oriented Polypropylene Film Standard Test Method for Permeability of Thermoplastic Containers to Packaged Reagents or Proprietary Products Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting Standard Specification for Dimensions and Tolerances for Plastic Bottles Standard Test Method for Rigidity of Polyolefin Film and Sheeting Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method Standard Test Method for Pendulum Impact Resistance of Plastic Film Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications Standard Practice for Preparing Plastic Film Specimens for a Round-Robin Study Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop Standard Test Method for Package Yield of Plastic Film Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications Standard Specification for Polyethylene Films Made from Low-Density Polyethylene for General Use and Packaging Applications Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm [0.010 in.] and Greater Standard Specification for Polyethylene Terephthalate Film and Sheeting Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements Standard Practice for Cutting Film and Sheeting Test Specimens Standard Guide for Determination of Thickness of Plastic Film Test Specimens Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors Standard Guide for Defect Detection and Rating of Plastic Films Using Optical Sensors
Standard Practice for Packaging/Packing of Plastics Standard Classification System for Specifying Plastic Materials Standard Guide for Writing Material Standards in the Classification D4000 Format Standard Guide for Reporting Properties for Plastics and Thermoplastic Elastomers
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics Standard Test Method for Tensile Properties of Plastics Standard Test Method for Compressive Properties of Rigid Plastics Standard Test Method for Shear Strength of Plastics by Punch Tool Standard Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials Standard Test Method for Bearing Strength of Plastics Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures Standard Terminology for Plastics: Dynamic Mechanical Properties Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior Standard Test Method for Chip Impact Strength of Plastics Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam) Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) Standard Guide for Material Properties Needed in Engineering Design Using Plastics Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) Standard Test Methods for Physical Dimensions of Solid Plastics Specimens Standard Test Method for Determining J-R Curves of Plastic Materials Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending Standard Test Method for Flatwise Flexural Impact Resistance of Rigid Plastics Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine Standard Test Method for Creep Measurement of Self-Lubricating Bushings Standard Test Method for Flexural Fatigue Properties of Plastics Standard Test Method for Uniaxial Fatigue Properties of Plastics
Standard Test Method for Index of Refraction of Transparent Organic Plastics Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics Standard Test Method for Transparency of Plastic Sheeting Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics Standard Test Method for Color Determination of Plastic Pellets
Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
Standard Specification for Chlorinated Polyethylene (CPE) Sheeting f or Concealed Water-Containment Membrane Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit Standard Test Method for Impact Resistance of Poly(Vinyl Chloride) (PVC) Rigid Profiles by Means of a Falling Weight Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit Standard Test Method for Predicting Heat Buildup in PVC Building Products Standard Test Method for Windload Resistance of Rigid Plastic Siding Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems Standard Test Method for Relative Rigidity of Poly(Vinyl Chloride)(PVC) Siding Standard Specification for Color and Appearance Retention of Solid Colored Plastic Siding Products Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe Standard Specification for Color and Appearance Retention of Variegated Color Plastic Siding Products Standard Specification for Polypropylene (PP) Siding Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) Standard Specification for Insulated Vinyl Siding Standard Specification for Color and Appearance Retention of Solid and Variegated Color Plastic Siding Products using CIELab Color Space
Standard Test Method for Compressive Properties of Plastic Lumber and Shapes Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between –30 and 140°F (–34.4 and Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards Standard Specification for Polymeric Piles Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications
Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics Standard Practice for Determination of Contamination in Recycled Poly(Ethylene Terephthalate) (PET) Flakes and Chips Using a Plaque Test Standard Practice for Separation and Identification of Poly(Vinyl Chloride) (PVC) Contamination in Poly(Ethylene Terephthalate) (PET) Flake Standard Practice for Separation of Contaminants in Polymers Using an Extruder Filter T est Standard Practice for Separation and Washing of Recycled Plastics Prior to Testing Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe Standard Classification for Machine-Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings Standard Test Method for External Pressure Resistance of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Standard Test Method for Beam Deflection of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Under Full Bore Flow Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Standard Specification for Centrifugally Cast "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflec ted Condition Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and Wetwells Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals Standard Specification for Fiber-Reinforced Plastic Fans and Blowers Standard Test Method for Determining the Chemical Resistance of Fiberglass-Reinforced Thermosetting Resins by One-Side Panel Exposure Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced Plastic Chimney Liners with Coal-Fired Units Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Av iation Jet Turbine Fuel Lines Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings Standard Specification for Polymer Concrete Pipe
Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics Standard Practice for Classifying Visual Defects in Parts Molded from Reinforced Thermosetting Plastics Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts Standard Test Method for Ignition Loss of Cured Reinforced Resins Standard Test Methods for Void Content of Reinforced Plastics Standard Practice for Classifying Reinforced Plastic Pultruded Shapes According to Composition Standard Test Method for In-Plane Shear Strength of Reinforced Plastics Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes Standard Terminology Relating to Reinforced Plastic Pultruded Products Standard Practice for Classifying Visual Defects in Thermosetting Reinforced Plastic Pultruded Products Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock Standard Test Method for Determination of Reactivity of Unsaturated Polyesters and Vinyl Esters at 180.0F [82.2°C]
Standard Practice for Testing Pultruded Composites
Standard Test Method of Measuring Shrinkage f rom Mold Dimensions of Thermoplastics Standard Practice for Determining Surface Temperature of Molds for Plastics Standard Practice for Transfer Molding Test Specimens of T hermosetting Compounds Standard Practice for In-Line Screw-Injection Molding Test Specimens From Thermosetting Compounds Standard Practice for Injection Molding Test Specimens of T hermoplastic Molding and Extrusion Materials Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets Standard Practice for Compression Molding Test Specimens of Thermosetting Molding Compounds Standard Test Method for Measuring Shrinkage from Mold Dimensions of Molded Thermosetting Plastics
Standard Terminology Relating to Plastics Standard Terminology for Abbreviated Terms Relating to Plastics Standard Guide for Description of Polymer Pellet Defects
Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position Standard Test Method for Coefficient of Linear T hermal Expansion of Plastics Between −30°C and 30°C with a V itreous Silica Dilatometer Standard Test Method for Molding Index of Thermosetting Molding Powder Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer Standard Test Method for Vicat Softening Temperature of Plastics Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact Standard Test Method for Determining Ignition Temperature of Plastics Standard Test Method for Density of Smoke from the Burning or Dec omposition of Plastics Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position
Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry
Standard Classification System and Basis for Specifications f or Cellulose Acetate Molding and Extrusion Compounds Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds Standard Specification for Ethyl Cellulose Molding and E xtrusion Compounds Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds Standard Test Methods for Determination of Solution Viscosities of Polyamide (PA) Standard Test Methods for Sampling and T esting Plasticizers Used in Plastics Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes
Standard Specification for Poly(Vinyl Chloride) Resins Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds Standard Test Method for Apparent Viscosity of Plastisols and Organosols at High Shear Rates by Extrusion Viscometer Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates Standard Practice for Oven Heat Stability of Poly(Vinyl Chloride) Compositions Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials Standard Test Method for Methanol Extract of Vinyl Chloride Resins Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds Standard Practice for Testing Plasticizer Compatibility in Poly(Vinyl Chloride) (PVC) Compounds Under Humid Conditions Standard Test Methods for Powder-Mix Time of Poly(Vinyl Chloride) (PVC) Resins Using a Torque Rheometer Standard Practice for Fusion of Poly(Vinyl Chloride) (PVC) Compounds Using a Torque Rheometer Standard Specification for Polybutylene (PB) Plastics Molding and Extrusion Materials Standard Specification for Crosslinkable Ethylene Plastics Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride Resins Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials Standard Practice for Compatibility of Plasticizers in Poly(Vinyl Chloride) Plastics Under Compression Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing Standard Specification for FEP-Fluorocarbon Tube Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials Standard Specification for PTFE Resin Skived Tape Standard Specification for Polyethylene Plastics Pipe and Fittings Materials Standard Test Method for Plasticizer Sorption of Poly(Vinyl Chloride) Resins Under Applied Centrifugal Force Standard Specification for FEP-Fluorocarbon Sheet and Film Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film Standard Practice for Determination of Gels (Fisheyes) In General-Purpose Poly(Vinyl Chloride) (PVC) Resins Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Pressure Applicati Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material
Standard Classification System and Basis for Specifications f or Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials Standard Classification System for Nylon Injection and Extrusion Materials (PA) Standard Classification System for and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using AST Standard Specification for Polypropylene Injection and Extrusion Materials Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Appli Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Diff erential Scanning Calorimetry Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) Standard Classification System for Acrylonitrile-Butadiene-Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials Standard Specification for Filled Compounds of Polytetrafluoroethylene (PTFE) Molding and Extrusion Materials Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric Standard Specification for Polyethylene Plastics Molding and Extrusion Materials Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources Standard Classification System for Polyamide-Imide (PAI) Molding and E xtrusion Materials Standard Classification System for Polyetherimide (PEI) Materials Standard Classification for Chemical Resistance of Poly(Vinyl Chloride) (PVC) Homopolymer and Copolymer Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Com Standard Specification for Polyphthalamide (PPA) Injection Molding Materials Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes Standard Classification for Recycled Post-Consumer Polyethylene Film Sources for Molding and Extrusion Materials Standard Test Method for Determination of Xylene Solubles in Propylene Plastics Standard Classification System for Copolymers of V inylidene Fluoride (VDF) with Other Fluorinated Monomers Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology Standard Classification System for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods
Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA) Standard Specification for Molded Polyethylene Shipping and Storage Drums Standard Guide to Standard Test Methods for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape Standard Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC) Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM) Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPVs) Based on ASTM Standard Test Methods Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) I njection Molding and Extrusion Materials Using ISO Methods Standard Specification for Sulfone Plastics (SP) Standard Specification for Finished Parts Made from Polyimide Resin Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE) Standard Specification for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or T ape Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE) Standard Classification System and Basis for Specifications f or Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM& Standard Specification for Perfluoroalkoxy (PFA)-Fluoropolymer Tubing Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE) Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended f or General Use Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI) Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using I SO Protocol and Methodology Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents
Standard Specification for Melamine-Formaldehyde Molding Compounds Standard Specification for Urea-Formaldehyde Molding Compounds Standard Specification for Thermosetting Polyester Molding Compounds Standard Specification for Allyl Molding Compounds Standard Specification for Epoxy Resins Standard Specification for Epoxy Molding Compounds Standard Test Method for Corrosivity Index of Plastics and Fillers Standard Specification for Molding Compounds, Thermosetting
phy phy
ary Gas Chromatography (HS-CGC)
hy (LC)
hy
of Flight (TOF) Mass Spectrometry (MS)
tography
oculum lly Composted in Municipal or Industrial Facilities
60°C)
ns
