AN2389 Application note An MCU-based low cost non-inverting buck-boost converter for battery chargers Introduction As the demand for rechargeable batteries increases, so does the demand for battery chargers. There are different kinds of design solutions available for implementing battery chargers. Some of them are dedicated hardware based solutions and some are microcontroller based solutions. In a microcontroller based solution, you have the flexibility of using the same hardware for charging different batteries and making only slight changes in the software. But there are still some challenges and one of the major challenges is to have a suitable input power supply available. Generally the Buck converter converter topology is used as a DC- DC converter to provide the controlled output power supply to the batteries. But in this case a problem may arise, for example, if you want to charge a 4.2V Li-ion batteries batter ies from a 5V supply due to the presence of the protection diode and other small drops across other components. This drop is generally about 1V which makes it very difficult to provide 4.2V to the Li-ion batteries using the buck converter topology. topology. This application note describes a simple technique for implementing a non-inverting buckboost converter which requires only one inductor. This converter is basically the result of cascading a Buck converter with a Boost converter. This converter can be controlled by two PWM signals from the microcontroller and can be used as a Buck converter or Boost converter whenever required. So this solution combined with the flexibility of the ST7 microcontroller can be used to charge a wide range of the batteries using the same hardware. The example used in this application note is specific to battery chargers but this DC-DC converter can be very useful for portable applications in general or any application which uses rechargeable batteries.
August 2007
Rev 1
1 / 16 www.st.com
Contents
AN2389
Contents 1
Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Theory of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
4
2.1
Buck-boost implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2
Buck converter implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3
Boost converter implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Selection of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1
Inductor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2
Capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application in battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.1
Theory of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2
Software flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5
Test environment and results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2/16
AN2389
1
Circuit diagram
Circuit diagram The diagram in Figure 1 shows the structure of the modified buck-boost converter. Figure 1.
Modified buck-boost converter PWM1
L
d2
P+ SW1
d1 VIN
PWM2
SW2
C VOUT
P-
3/16
Theory of operation
2
AN2389
Theory of operation You can use this converter as buck-boost converter, as a buck converter or as a boost converter by selecting different combinations of switches SW1 and SW2 driven by the PWM1 and PWM2 signals output by the ST7 microcontroller.
2.1
Buck-boost implementation This converter can be used as a non inverting buck-boost converter by selecting the operating mode from Table 1 which briefly describes the converter modes. .
Table 1.
Operating modes based on switch combinations
Phase
SW1 (PWM1)
SW2 (PWM2)
Operating modes
1
OFF
OFF
BUCK
2
OFF
ON
N/A
3
ON
OFF
BUCK-BOOST
4
ON
ON
BOOST
If we look at phase 2 in Table 1, here the switch SW1(PWM1) is OFF and switch SW2 (PWM2) is ON. This condition never occurs either in a buck converter or in boost converter. So you should always take care in your software that this condition must not happen. To avoid this, if we assume that initially both switches are in OFF condition then you should use the following guidelines to manage the PWM signals driving the two switches.
4/16
1.
Keep the frequency of both PWM signals the same, to better control when synchronizing the two PWM signals using the next three guidelines.
2.
The duty cycle D1 of control signal PWM1, must be greater than the duty cycle D2 of control signal PWM2.
3.
PWM1 should be enabled before the PWM2 signal.
4.
PWM1 should be disabled after the PWM2 signal.
AN2389
Theory of operation Figure 2.
Timing diagram for two PWM signals
Phase 3
PWM1
PWM2
Phase 4
Phase 1
Figure 2 shows a timing example for the two PWM signals based o n the above guidelines. Here phase 2 does not occur. –
If the duty cycles of the two PWM signals driving SW1(PWM1) and SW2 (PWM2) are D1 and D2 respectively and
–
if we exclude the saturation voltage of the switches from our calculation and
–
if the drop across the diodes is Vd1 and Vd2 respectively,
–
then the output voltage Vout is given by the following formula:
Vout = [ Vin * D1 - Vd1 * ( 1 - D1) ] / ( 1 - D2) - Vd2
As mentioned in [2], theoretically this converter works linear ly over a gain range of 0 - 200% of the input voltage.
5/16
Theory of operation
2.2
AN2389
Buck converter implementation If you keep SW2 always in OFF condition and drive SW1 (PWM1) with a PWM signal from the microcontroller then the circuit works like a buck converter, except that you have an additional diode drop Vd2 due to diode d2. Figure 3.
Buck converter implementation PWM1
L
d2
P+
d1 VIN
OFF
SW2
C VOUT
P-
If the duty cycle of the PWM signal driving SW1 (PWM1) is D1, the output voltage will be given by: Vout = Vin * D1 - Vd1 ( 1 - D1) - Vd2
6/16
AN2389
2.3
Theory of operation
Boost converter implementation Again if you keep switch SW1 (PWM1) always in ON condition and drive the Switch SW2 (PWM2) with a PWM signal generated by the microcontroller, then the combination works as a boost converter except that you have an additional free wheeling diode D1 which you can ignore. Figure 4.
Boost converter implementation ON
L
d2
P+ SW1
d1 VIN
PWM2
SW2
C VOUT
P-
If the input voltage is Vin, the duty cycle of the PWM signal driving PWM2 is D2 and the drop across the diode d2 is Vd2, then the output voltage Vout is given by: Vout = Vin / ( 1 - D2) - Vd2
7/16
Selection of components
3
AN2389
Selection of components The inductor and capacitor can be selected using the formulae given below.
3.1
Inductor selection The minimum value of the inductor can be selected by choosing the maximum of the values given by the following two formulae:
Lmin =
T * [ ( V in - Vsat1) * D1 - Vsat2 * D2 - Vout * (D1 - D2)]
(1)
2 * Iout
Lmin =
(2)
T * [ Vd1 + Vout] * ( 1 - D1) 2 * Iout
Here Vsat1 and Vsat2 are the saturation voltages of the two switches SW1 and SW2. Iout and Vout are the maximum output current and voltage respectively. Vd1 and Vd2 is the drop across diodes d1 and d2. The duty cycles of the PWM signals driving SW1 and SW2 are D1 and D2 respectively.
3.2
Capacitor selection The minimum of the capacitor value can be selected by using the following formula , assuming a variation in Vout of 1% or less Cmin =
100 * Iout * (1 - D1) * T
(3)
Vout
In practice, we take inductor and capacitor values that are larger than the values calculated using the above formulae.
8/16
AN2389
4
Application in battery charger
Application in battery charger We can use the modified non-inverting buck-boost converter in a combination of different modes as required by the application.
4.1
Theory of operation The DC-DC converter uses a combination of buck-boost converter and boost converter mode to charge the Li-ion battery. In case of Li-ion, the constant current constant voltage (CC CV) charging algorithm is used to charge the batter y. Here we have chosen the input voltage just enough to show the functionality of the converter in buck-boost mode and boost mode. Initially the converter works in Buck-Boost converter mode to charge the battery in constant current mode by keeping the duty cycle of PWM2 constant and varying the duty cycle of PWM1. As soon as there is an overflow condition for the duty cycle of PWM1. The converter switches from buck-boost converter mode to boost converter mode. And then duty cycle of PWM2 is varied to follow the algorithm while SW1 remains in ON condition. Following section shows the software flow chart for this combination.
9/16
Application in battery charger
4.2
AN2389
Software flowchart There are many ways in which you can control the operation of this circuit. An example algorithm which can be used for in Li-ion battery charger is given belowFigure 5.
Li-ion battery charger flowchart
INITIALIZE THE PWM SIGNALS WITH DUTY CYCLE D1 AND D2.
WORKS IN BUCK-BOOST MODE. KEEP D2 FIXED AND VARY D1 TO KEEP THE CURRENT CONSTANT.
IS THERE A OVERFLOW IN
No
D1? YES
WORKS IN BOOST MODE. KEEP SW1 ALWAYS ON AND VARY THE D2 TO CONTINUE THE ALGORITHM BY KEEP -ING THE CURRENT OR VOLTAGE CONSTANT AS REQUIRED.
END
10/16
AN2389
5
Test environment and results
Test environment and results We used this buck-boost converter in the universal battery charger evaluation board described in AN2390. Figure 6 below shows the general battery charger circuit using the non-inverting buck-boost converter circuit mentioned in this application note. For simplicity, this figure does not show all the connections. Figure 6.
General circuit-based battery charger PWM1
d2
L
P+ SW1 IBAT
d1
PWM2
SW2
VIN
C VOUT
Battery
VBAT
RS Sense resistor
P-
Here some results are shown for charging the Li-ion battery using this converter in buckboost mode. The above charger is is intended for charging a single Li-ion or two NiMH in series using a 5V supply input. Details on the implementation are given in AN2390 where you can find results for NiMH batteries as well as for a charger used simply in buck converter mode. Some parameter values are as follows: Vin = 5V, Iin (MAX) = 2A, Vsat1 = Vsat2 = 0.3V, Vd1 = Vd2 = 0.5V. and PWM frequency for both PWM1 and PWM2 = 16KHz. Also let’s say the maximum value of Vout = 5.5V and Iout = 1.2A and the maximum duty cycle of D1 is 95% and D2 is equal to 30%. Then using the formulas given in Section 3 : Lmin = 21 uH (from equation 1) or 10 uH (from equation 2). So we should choose a value larger than 21 uH. Cmin = 70uF (from equation 3). So we need to choose a value higher than 70 uF. In this example, L = 75 uH, C = 470 uF are taken, which are larger than the values calculated using the formulas hence will support the application. The following table shows some of the readings taken for different values of the duty cycles D1 and D2.
11/16
Test environment and results I
Table 2.
AN2389
Input vs output
Sl No
Vin (V)
Iin (A)
Vout (V)
Iout (A)
1
5
1.23
3.9
1.05
2
5
1.33
4.14
1.05
3
5
1.36
4.2
1.05
4
5
1.27
4.2
0.975
5
5
0.97
4.2
0.80
6
5
0.85
4.2
0.712
7
5
0.65
4.15
0.55
8
5
0.33
4.15
0.28
9
5
0.31
4.15
0.26
10
5
0.16
4.10
0.129
In above results, we have not added Vsat (0.3V), diode drop (0.5V) and the drop across the series resistor (connected to measure batter y current) as shown inFigure 6 to get the actual output voltage of the non-inverting buck-boost converter. For example it is given that Vout (battery voltage) = 4.2V, but the actual output voltage of the converter is equal to: Vout 4.2V (Battery Voltage Vbat) + 0.3V(Switch Drop Vsat1)+ 0.5V(Protection Diode Vd2)+ 0.4V (Drop across Sense resistor) = 5.4V. So we are able to achieve 5.4V from a 5V supply thus validating the concept.
12/16
AN2389
6
Conclusion
Conclusion This application note describes a simple but very useful technique for implementing a microcontroller controlled low cost non-inverting buck-boost converter. This converter can be used as a buck converter or as a boost converter or as a buck-boost converter. The example shows the application of this converter in a batter y charger. However it can also be used in other portable applications or any application getting its power from a rechargeable battery. Or you could use this technique to make a USB charger to charge Li-ion batteries or 3 or more NiMH Cells in series.
13/16
References
7
AN2389
References [1] AN2390: “A flexible universal battery charger”, STMicroelectronics [2] “A noninverting buck-boost converter with reduced components using a microcontroller” by Robert S. Weissbach and Kevin M. Torres, IEEE members.
14/16
AN2389
8
Revision history
Revision history Table 3.
Document revision history
Date
Revision
21-Aug-2007
1
Changes Initial release.
15/16
AN2389
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
16/16
