chapter 3

CHAPTER 3

METHODOLOGY

3.1 INTRODUCTION

In this project, to ensure that the project flow is developed smoothly, deep and systematic planning is needed to be taken. This chapter will give details and elaborates further regarding to the methods used to develop this project along with reasons of choosing such methods and tools. In this methodology chapter, it is focus on the flow chart, literature review, and experimental result for the first stage.

3.2 FLOW CHART OF METHODOLOGY

Each part of the procedure need to organize wisely in order to ensure the  project is running smoothly. smoothly. Therefore, the step and flow of this project can be representing by using the flowchart. ne of the advantages of via the flowchart is when there are any problems happen during this project, it possibly will be solve by refer to the flowchart. Thus, the procedure of development this project is represent by the flowch flowchart art method methodolo ology gy as shown shown in !igure !igure ".#.In ".#.In this this project project,, hardwa hardware re is important since it is the most important tools that are used on the development of this  project.

)T*(T

'iterature (eview

%ardware &esign

%ardware &evelopment

%ardware Testing

 + perating )atisfy E) (ecord (esult

-riting (eport

E+&

!igure ".#$ !low chart of project course

i

Literature Review

The literature review part will explain detail about the reference source and fact finding in an attempt to develop this project successfully.

ii

Harware De!i"#

This part is concerning detail about the list of euipment and devices including the schematic design of this project.

iii

Harware Deve$%&'e#t

*fter designing the project, the hardware is ready to be develops by following to the schematic design.

iv

Harware Te!ti#"

%ardware is reuired to be test after the project is fully develops. This is necessary to ensure the project is in good condition.

v

O&erati#" (ati!)*

perating satisfies is the process to ensure the hardware is running perfectly. If the hardware is good condition this project will proceed to the experimental part. If the hardware is not satisfied, the process will turn back to the hardware design.

vi

Re+%r Re!u$t

*fter the hardware testing is satisfy, the experimental of this project is run and the result will be record. Therefore, the report can be proceeding after the result is record.

3.2.1

F$%w C,art %) Fire Fi",ti#" R%-%t

)T*(T

&evice on

!lame sensor detect fire

*rduino send data to '/01+

'/01+ control motor 

E+&

LI(T OF COMPONENT U(ED

NAME *(&2I+ '/01+ %3678 9*TTE( #/4 ;25:E( &3 5T(

U(ED FOR   !( 3+T(' &E4I3E 3+T(' 5T(   !( 3++E3T -IT% &E4I3E )2::' :-E( &E4I3E 2)E& T 3++E3T 3I(32IT !( *33E'E(*TI+

3.3 LOC/ DIAGRAM

L298N

MOTOR

ARDUINO UNO R3

Flame Sensor

DEVICE

3.0 GANTT CHART

DISEMBE FEBRUAR R JANUARY    Y MARCH M M M M M M M M M M M M M M M M 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 Projec t Discus sion

Initia Pro!o sa

C"a!t er 1 C"a!t er 2

C"a!t er 3

Prese ntatio n

PreLiera!r e Re"ie# PrePro$lem Saeme n PreO$%e&i"e Pro$lem Saeme n O$%e&i"e S&o'e Liera!r e Re"ie# Me(o)ol o*+ Lis o, Com'one n Cir&!i Desi*n