To Check Major alarm Allip: acl=a2; This command shows mains power failure, tre faults,Outage e.t.c To check critical alarm Allip: acl=a1; this command shows low fuel, Common alarms, if is Gen set ON, AC alarms, rectifier alarms e.t.c To check Minor alarm Allip: acl=a3; RXMFP: MO=RXOCF-tgno; this shows battery backup also cf status RXMOP: MOTY=RXOTG; this printout all sites corresponding their TG RXCDP: MO=RXOTG-TGNO; shows status of site (if the site is up shows configured s tatus and if the site is down shows blocked status) To check the tg frequency type -
rxcdp:mo=r rxcdp:mo=rxotgxotg-tgno. tgno.; ; tgno- transceive transceiver r group number number
To check in which sector or channel group the tg is present -
rxmop:mo=rxotrx-17-2;
To print site name - rxmop:mo=rxotg-tgno.; To check frequency of the cell -
rlcfp:cell=cellno.;
To active unused cell -
rlstc:cell=cellno,chgr=0 or 1,state=halted; rlstc:cell=cellno,chgr=0 or 1,state=active;
To check for traffic in the sector -
rlcrp:cell=cellno.;
To change handover relations -
rlmfc:cell=cellno,mbcchno=mbcchno,listtype=listtype;
listtype can be active & idle mbcchno=frequency number -
rlmfp:cell=cellno;
cell measurement frequencies To load software remotely -
rxpli:mo=rxotg-tgno,uc;
To check if loading of s/w is over -
rxmsp:mo=rxocf-tgno;
To check cell ID of the cell -
rxtcp:mo=rxotg-tgno;
Cell printing -
rlcrp:cell=all;
Reseting the site -
rxbli:mo=rxocf-tgno,force; rxble:mo=rxocf-tgno;
To know the DIP no of the site -
rxapp:mo=rxotg-tgno; ntcop:snt=all; or ntcop=etm2-tgno;
To check if there is any signaling link down in the MSCs - c7ltp:ls=all;
If there is restoring then the signaling is not working
To check CGI if defined correctly -
mgcep:cell=cellID;
To change CGI -
1. Halt cell rlstc:cell=cellID,chgr=0 or 1,state=halted; 2. rldec:cell=cellID,cgi=640-05-9-cellID; 3. Activate cell rlstc:cell=cellID,chgr=0 or 1,state=active;
To check E1 for sites in the BSC -
dtstp:dip=all;
To check which cell are in extended range -
rldep:cell=all,xrange;
To check which cells are set in OL/UL -
rldgp:cell=cellno; rlcfp:cell=cellno.;
To delete a sector 1st block the trx i.e. rxbli:mo=rxotrx-30-4,subord,force; 2nd put trx out of service i.e. rxese:mo=rxotrx-30-4,subord; 3rd rxmoe:mo=rxots-30-4-0&&-7; rxmoe:mo=rxotx-30-4;
rxmoe:mo=rxorx-30-4; rxmoe:mo=rxotrx-30-4;
4th rlstc:cell=cellno,state=halted,chgr=0 or 1; rxtce:mo=rxotg-30,cell=cellno,chgr=0 or 1; rlsle:cell=cellno,perm; rldee:cell=cellno; To check if the cell is active or halted -
rlstp:cell=cellno;
To get TG number -
rxtcp:moty=rxotg,cell=cellno;
To check the TS -
rxmsp:moty=rxots;
To check which faulty code comes from a faulty tre -
rxmfp:mo=rxotx-tgno-trxno;
To lock a sector -
rlstc:cell=cellno,state=halted;
To unlock a sector -
rlstc:cell=cellno,state=active;
Upgrading a sector
CELL 2684
CHGR 0 2685
0
2686
0
END
SCTYPE
SDCCH 1
SDCCHAC 0
TN 2
CBCH NO
HSN 39
HOP OFF
DCHNO 665
RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT CONFIGURATION DATA MO RXORX-30-0 RXORX-30-4 RXORX-30-8
RESULT CONFIG CONFIG CONFIG
ARFCN HOP HOP HOP
MISMATCH NONE NONE NONE
MO RXOTS-30-0-0 RXOTS-30-0-1 RXOTS-30-0-2 RXOTS-30-0-3 RXOTS-30-0-4 RXOTS-30-0-5 RXOTS-30-0-6 RXOTS-30-0-7 RXOTS-30-4-0 RXOTS-30-4-1 RXOTS-30-4-2 RXOTS-30-4-3 RXOTS-30-4-4 RXOTS-30-4-5 RXOTS-30-4-6 RXOTS-30-4-7 RXOTS-30-8-0 RXOTS-30-8-1 RXOTS-30-8-2 RXOTS-30-8-3 RXOTS-30-8-4 RXOTS-30-8-5 RXOTS-30-8-6 RXOTS-30-8-7
RESULT CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG CONFIG
ARFCN 665 665 665 665 665 665 665 665 701 701 701 701 701 701 701 701 710 710 710 710 710 710 710 710
TXAD 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
TN 0 2 7 6 5 4 3 1 0 2 7 6 5 4 3 1 0 2 7 6 5 4 3 1
MO RXOTX-30-0 RXOTX-30-4 RXOTX-30-8
RESULT CONFIG CONFIG CONFIG
ARFCN 665 701 710
TXAD 2 1 0
BSPWR 45 45 45
BPC 4500 4498 4482 4470 4467 4465 4463 4462 4505 4504 4491 4489 4488 4484 4480 4469 4493 4495 4497 4486 4481 4468 4466 4464
CHCOMB BCCH SDCCH8 TCH TCH TCH TCH TCH TCH BCCH SDCCH8 TCH TCH TCH TCH TCH TCH BCCH SDCCH8 TCH TCH TCH TCH TCH TCH
OFFS 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
C0F YES YES YES
MISMATCH NONE NONE NONE
64K NO NO NO NO NO NO NO NO NO NO NO
TEI
END
DCP 19
RBLT2-596 RBLT2-597 RBLT2-598 RBLT2-599 RBLT2-600 RBLT2-601 RBLT2-602
20 21 22 23 24 25 26
APUSAGE MPLEX16 MPLEX16 MPLEX16 MPLEX16 UNDEF CONC CONC UNDEF UNDEF UNDEF UNDEF
APSTATE SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA IDLE CF/TRXC SIGNAL TRXC SIGNAL IDLE IDLE IDLE IDLE
61 4
0
8
XRA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO
ICM ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
RBLT2-603 RBLT2-604
27 28
RBLT2-605
29
RBLT2-606
30
RBLT2-607
31
UNDEF MPLEX16 MPLEX16 MPLEX32 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16 MPLEX16
IDLE SPEECH/DATA SPEECH/DATA IDLE SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA SPEECH/DATA
NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO
END
CELL 2684
CHGR ALL
SWVERREPL DEFAULT
TEI 0 SWVERDLD B1922R002U
SIG CONC SWVERACT B1922R002U
DCP1 128 DCP2 129 130
END
EXECUTED
RESULT ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED
END
STATE NOOP PREOP PREOP PREOP PREOP PREOP PREOP PREOP PREOP PREOP PREOP
RESULT EXECUTED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED ORDERED
END Changing frequency of a TRX in cell rlcfp:cell=3082;
! u get the existing frequency(ies) in cell 3082 !
suppose you want to remove freq= 109 and put 90 insted, you will have to end that freq. eg. 109 ! rlstc:cell=3082,state=halted; rlcfe:cell= cell=3082,dhno= 109;
rlcfi:cell=3082,dhno=90;
! adding freq. 90 in a mentioned cell!
rlstc=cell=3082,state=active;
activate !! and check !!.
Cell Dynamic HR allocation Data rldhp:cell=cellno; This command will show the values of DTHAMR( Dynamic Threshold Half rate Adaptive Multi Rate) and DTHANMR (Dynamic Threshold Half rat e Non Adaptive Multi Rate)
Cell Adaptive Logical Channel configuration rlacp:cell=cellno; If ACSTATE= ON, then there is a dynamic SDCCH in the cell Cell General Packet Radio Service Data -rlgsp:cell=cellno; This shows the value of FPDCH in the cell To check neighbour relation of the cell -rlnrp:cell=cellno; To print all neighbours of the cell
Cell Locating Hierarchical Data -rllhp:cell=cellno; To get the Layer Threshold ( LAYERTHR) value OF A CELL
To Check Major alarm Allip: acl=a2; This command shows mains power failure, tre faults,Outage e.t.c To check critical alarm Allip: acl=a1; this command shows low fuel, Common alarms, if is Gen set ON, AC alarms, rectifier alarms e.t.c To check Minor alarm Allip: acl=a3; RXMFP: MO=RXOCF-tgno; this shows battery backup also cf status RXMOP: MOTY=RXOTG; this printout all sites corresponding their TG RXCDP: MO=RXOTG-TGNO; shows status of site (if the site is up shows configured s tatus and if the site is down shows blocked status)
