Ericsson Command line:
**** RNC IPs ******
RNC Name
IP Address
UFSD212E_RNC_ZIAT WN_1
10.226.176. 196
UKHI210E_RNC_BAR Q_1
10.226.245. 4
UKHI211E_RNC_BAR Q_2
10.226.245. 5
UMUL213E_RNC_MLT RX_1
10.226.176. 212
RNC Level Commands Command
Description
lst m3ua
Displays M3ua Association status with MSS/MGW and SGSN. Also shows Operational state, Admin state of M3ua links of RNC.
lst mtp3
Displays MTP3b links [Backup signaling] Admin state, Operational state in RNC
lst sccp
Displays SCCP links Admin state, Operational State in RNC.
strt
Displays Total no. of available Cells, available sites, Unlocked cells in RNCs and Iub interfaces
st ranap
Displays RNC's connectivity status with CS and PS Core over A interface.
Nodeb, UtranCell Level Commands Command lst 'Nodeb name'
Description Displays all Utrancells under Nodeb along with their Admin and Operational States
st UtranCell='UtranC ell Name'
Displays current Admin , Operational state of a specific UtranCell
get ‘UtranCell Name’ uarfcndl
Displays DL frequency of a specific UtranCell
get ‘UtranCell Name’ uarfcnul
Displays UL frequency of a specific UtranCell
get 0
Displays NodeB type and other properties of Nodeb being used in RNC
********* CELL********** rlstp: cell=all;------------cell status rlgsp: cell=FSD0301A; Cell----Status of GPRS rlgap: cell=FSD0301A;------channel group allocation for the cell rlcfp: cell=FSD0301A; Cell----Show MA Group FP of Cell rlcfp: cell=FSD0301B; rlncp: cell=FSD0301B; Cell---Show internal Neighbours of cell rlnrp-----------All nei of cell rldep: cell=FSD0301B; Cell----- info LAC CID BCCH rlcrp:cell=HWY4705A; Cell resources rlstp:cell=all ,state=halted; rlslp:cell=RUR8101A; //gives info of underlaid / overlaid signalling channels raclp; RLNCP: CELL=CHO8031A; -------------- To check Neighbors of cell *********TRX************ rxtcp:moty=rxotg;==============TGs against all sites rxtcp:moty=rxotg,cell=KBR3514A; //(Show TG of Cell) rxmsp: mo=RXOTRX-142-0&&-11; //(Show Status of TRX's on TG) rxmsp: mo=RXOTG-22,subord; //(Show Status of TS's on TRX) rxmop: mo=RXOMCTR-22-1, morel; //(Show TRX mapped on MCTRX) rxmop: mo=RXOTRX-220-0&&-11; //(Show mapping of TRX on cells) rxmop: mo=RXOTX-21-0&&-11; //(Show mapping of TRX on cells, along with BAND) RXMOP:MO=RXOmctr-220-0&&-11, morel; // to check mctr of site RXMOP:MO=RXOTX-220-0&&-11; //to check power of mctr RLCPP:CELL=RUR1432A; rxmfp:mo=rxocf-273; //(Show Hardware of sites) rxasp:mo=rxotg-142;------alarm on specific tg rxasp:moty=rxotg;------------------alarms on all down TGs and their sites code
c7spp:sp=all; //to check OPC-DPC ioexp; //to check identity of BSC allip; BSC---- Alarms rripp:ipaddr=all; BSC-------IP of BSC rrapp:apl=ips; BSC------Voice sPEECH App IP's rrapp:apl=AIP; BSC----- a INTERFACE ips rrasp:rp=all;
//to check traffic on A-interface (AoIP)
*********M3LNKS****** m3rsp:dest=all; // (Status of M3LNKS) M3asp; // (Status of M3Lnks) m3rsp:dest=all; // (Display the status of M3UA links)
**********SCTPLNKs******* ihclp:epid=all,said=all; // (Displays the IP connectivity of SCTP links between BSC and MGW) ******* BSC *********** rripp:ipaddr=all; BSC-------IP of BSC rrapp:apl=ips;
BSC------Voice sPEECH App IP's
rrapp:apl=AIP;
BSC----- a INTERFACE ips
**********GB********** rrinp:nsei=all; // (shows IP connectivity of GB link) rrbvp:nsei=all; // (shows GB BVC status on the cell level) rrapp:apl=gbi; // (GB App IP's) ***********RP*********** rrrsp:rp=all; // Show status of all RP's raasp; // Show all EPB and RP's mapped on them exrpp:rp=all; //Show all RP's of Exchange along with PIU's exemp:rp=all,em=all; //Show all RP's and sub RP's of Exchange //(details of the blocks running on the EPB and EvoET ******************************************************** rxtcp:moty=rxotg,cell=BRW8368A; rxtcp:moty=rxotg,cell=JHG8416B; rxtcp:moty=rxotg,cell=JHG8416C;
rxmsp: mo=RXOTRX-311-0&&-11;-----trx cell wise RRSCP:SCGR=186;----------abis status against specific tg NTCOP:SNT=ETM4-0; DTQUP:DIP=1302SD; dtstp:dip=103sd; rrscp:scgr=46;--------status of abis against site (Status of E-1)
***** 3G ************* st UtranCEll=U2HGW04512A [ To check UtranCell status] lst U2KHI53282 [To check site current status.] get U2KHI07573A uarfcndl [DL Frequency CHeck] get U2KHI07573A uarfcnul [UL Frequency Check] get 0 [To check nodeB type and other info] st cell=U2KHI04622A [To check Cell state]
********* To check DIP Status**************
How to check DIP status?
rrscp:scgr=TG-#
SCGR SC DEV 217 0
DEV1 ETM4-7681
7680 +1 = 7681 ETM4
NUMDEV DCP STATE REASON 31
1 FLT
H'0001 0000
ntcop:snt=all;
5103SD ETM4-7680&&-7711
240
dtstp:dip=5103sd;
DIP
TYPE
STATE LOOP TSLOTL DIPEND FAULT
5103SD IEX
ABL
SECTION
AIS
ABL= Automatic Blocked WO= Working
***** DIP Status of All ******* ntcop:snt=all;
dtstp:dip=2300sd;
BSC LEVEL Command
Description
rrmbp:msc=all;
To get the name of MSC/MGW to which BSC is connected to
M3ASP;
To print M3UA status data for all defined SCTP associations of BSC
C7spp:sp=all;
To get OPC/DPC values of BSC
allip:acl=a1,alcat=ext/b ts;
To get all EXTERNAL alarms of BSC
allip:alcat=sw_dev;
To get all Internal Alarms of BSC
allip:acl=a1;
To check all active alarms at BSC with Severity CRITICAL
allip:acl=a2;
To check all active alarms at BSC with Severity MAJOR
allip:acl=a3;
To check all active alarms at BSC with Severity MINOR
rldep:cell=all
To get the list of all the sites in the BSC
BTS LEVEL Command rxtcp:moty=rxotg,cell=CELLNAME;(Get TG Value)rrscp:scgr=TG#
Description To check Abis state of a Site
rlcfp:cell=cellname;
To check the Frequency of a site
rlchp:cell=cellname;
To check if Hopping is enabled at a site or not
rlgsp:cell=cellname
To check if GPRS is enabled at site or not
rxtcp:moty=rxotg,cell=cellname;(get TG value)rxmsp:mo=rxocf-TG No,subord;
To check the Traffic Status at Site
rxbli:mo=rxocf-TG /CF #,subord,force;
To LOCK the Site
rxble:mo=rxocf-TG /CF #,subord;
To UNLOCK the Site
rxbli:mo=rxotrx-TG /CF #trx.No.,subord,force;
To LOCK a Radio in a Cell
rxble:mo=rxotrx-TG /CF #-trx.No.,subord;
To UNLOCK a Radio in a Cell
rxcdp:mo=rxotg-27(TG VALUE),details;
To get the Total no. of TRX of site.
rxmsp:mo=rxotrx-395-5;(TRX #)
To get status of a TRX. For more than 1 TRXs, use && operator
Ericsson Command Handling
Command Name
Description
ioexp;
Prints complete name of BSc
C7spp:sp=all;
Prints BSC's OPC/DPC data
allip;
Prints all alarms appearing on BSC
rrrsp:rp=all;
Prints all CTH, GPH configured on BSC
raasp;
Displays Boards, their slot configurations, CTH, GPH allocation etc.
exrnp:rp=all;
Prints RPs, their status, Magazine no and slot no.
dpwsp;
Prints CP working state.
rlcrp:cell=all;
Prints all cells connected to the BSC
Prints all cell's detailed description data (BCCH, CGI, LAC, rldep:cell=all; BSIC information etc.) rripp:ipaddr= all;
Prints all ip parameters of an IP device.
m3asp;
Prints M3UA status for SCTP association of BSC
rrinp:nsei=all ;
The NS parameters for all NSEIs are printed along with remote IP end point data and local IP end point data.
rrapp:ipaddr =all;
This parameter prints the Internet Protocol (IP) application
rlstp:cell=all;
Prints current status of all cells of BSC
rlstp:cell=all, state=active;
Prints all cells of BSC which are currently Active
rlstp:cell=all, state=halted;
Prints all cells of BSC which are currently Down.
Command
Description
rrmbp:msc=all;
Command prints all MSC data defined in BSC along with MSC design identifier.
rxmsp:mo=rxotg-4;
Prints current status of TG.
rxmsp:mo=rxotg-4,subord;
Prints current status of TG, all TRX under this TG and TS of TG.
caclp;
Prints local time stamp from system, cane be used with parameter '
c7spp:sp=all;
Prints SP data, OPC/DPC,BSC Name, MSC Name etc
rlcfp:cell=hwy1273a;
Prints Cell Frequency Data for one, several or all internal cells.
rldep:cell=hwy1273c;
Prints Cell description Data, Cell System Type,Xrange Cell info,Extern info,LAC info
rlstp:cell=all,state=halted/ active
Prints all internal cells with state designated
rxasp:moty=rxotrx;
Prints all alarm situations currently outstanding in BSC, All OML Fault
rxasp:moty=rxotg;
prints all kind of faults at TRX level in BSC
dtstp:dip=all,state=wo/AB L/MBL;
Prints Digital Path State [DIP] of all PCM
rxmop:mo=rxotg-162;
Prints all administration related data of TG and Site version
rxmfp:mo=rxotrx-226-1;
Huawei Command Line
LST M3DE, Shows Destination Entity list connected with NE. LST SCTP , signaling, M3UA LNKS. Shows all Signalling IPs. LST IPROUTE, shows all IPs of BSCs towards MSS/MGW/SGSN LST IPPATH LST NSVLlocal, Shows BSC IP for PS service LST NSVLRemote, Shows Remote end for PS Service lst devip, Shows Logical IP Address of BSC
