CONTENTS
ROI-S04488-05PE November, 2005
7-38 GHz 4/8/17/34 MB DIGITAL MICROWAVE RADIO SYSTEM PASOLINK (1+0/1+1 SYSTEM)
MDP-[ ]MB-[ ] EQUIPMENT DESCRIPTION CONTENTS TITLE 1
PAGE
GENER GENERAL AL •••••• ••••••••• •••••• •••••• •••••• •••••• ••••• ••••• •••••• ••••• ••••• •••••• •••••• ••••• ••••• •••••• ••••• ••••• •••••• •••••• ••••• •• 1-1 1-1
1.1
Equipm Equipmen entt Compo Composit sitio ion••• n•••••• •••••• •••••• •••••• •••••• ••••• ••••• •••••• •••••• •••••• ••••• ••••• ••••• •• 1-5 1-5
1.2
Equip Equipme ment nt Perfor Performan mance•• ce••••• •••••• •••••• •••••• •••••• •••••• ••••• ••••• ••••• ••••• •••••• •••••• ••••• •• 1-10 1-10
2
FUNC FUNCTI TION ONAL AL OPERA OPERATIO TION•• N••••• •••••• •••••• •••••• •••••• ••••• ••••• •••••• ••••• ••••• •••••• ••••• ••••• ••••• 2-1 2-1
2.1 2.1
Tran Transm smit it Lin Line e Equa Equali liza zati tion on •••• •••••• •••• •••• •••• •••• •••• •••• •••• •••• •••• •••• •••• •••• •••• •••• •• 2-17 2-17
2.1.1 2.1.1
Bipola Bipolar-to r-to-Un -Unipo ipolar lar Code Code Convers Conversion ion •••• ••••••••• •••••••••• ••••••••• •••••• •• 2-17
2.1.2 2.1.2
Multipl Multiplexi exing ng •••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-17
2.1.3 2.1.3
Parallel Parallel-to -to-Ser -Serial ial Convers Conversion••• ion••••••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-17
2.2
Trans Transmi mitt Digi Digital tal Proce Process ssin ing g •••••• ••••••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• ••• 2-17
2.2.1 2.2.1
Multipl Multiplexi exing ng •••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-17
2.2.2 2.2.2
Scrambl Scrambling ing ••••• ••••••••• •••••••• •••••••• ••••••••• ••••••••• •••••••• ••••••••• ••••••••• ••••••••• •••••••••• ••••••••• •••••• •• 2-18
2.2.3 2.2.3
Parity Parity Check Check •••• •••••••• •••••••• ••••••••• •••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• ••••••••• ••••••••• •••••• •• 2-18
2.3
Modul Modulati ation on ••••• •••••••• •••••• ••••• ••••• •••••• •••••• ••••• ••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• ••••• •••• •• 2-18 2-18
2.3.1 2.3.1
Differe Differenti ntial al Encodi Encoding ng •••• ••••••••• ••••••••• •••••••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-18
2.3.2 2.3.2
4-Phase 4-Phase Shift Shift Keying Keying Modulat Modulation ion •••• ••••••••• •••••••••• ••••••••• •••••••• •••••••• •••• 2-19
2.3.3 2.3.3
Orderwi Orderwire re Signal Signal Modulat Modulation••••••• ion••••••••••• •••••••• •••••••• •••••••• •••••••• ••••••••• ••••• 2-20
2.4
Demo Demodu dula lati tion•• on••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• •••••• ••••• ••••• •••••• ••••• ••••• ••••• ••••• ••••• •• 2-20 2-20
2.4.1 2.4.1
EOW and Alarm Alarm Signal Signal Demodu Demodulati lation on •••• ••••••••• •••••••••• ••••••••• •••••• •• 2-20
2.4.2 2.4.2
Main Main Signal Signal Demodul Demodulati ation on ••••• •••••••••• •••••••••• ••••••••• ••••••••• ••••••••• •••••••• ••••••• ••• 2-21
2.4.3 2.4.3
Differe Differenti ntial al Decodi Decoding ng •••• ••••••••• ••••••••• •••••••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-21
2.5
Recei Receive ve Digit Digital al Proces Processi sing ng •••••• ••••••••• ••••• ••••• •••••• •••••• ••••• ••••• •••••• ••••• ••••• ••••• 2-22 2-22
2.5.1 2.5.1
Frame Frame Synchro Synchroniza nization tion •••• ••••••••• •••••••••• •••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-22 2-22
2.5.2 2.5.2
Descram Descrambli bling••••••• ng••••••••••• •••••••• •••••••• •••••••• •••••••• ••••••••• ••••••••• •••••••• •••••••• •••••••• •••••••• •••• 2-22
2.5.3
Demultiplexin Demultiplexing g •••••••••••••••••••••••••• ••••••••••••••••••••••••••••••••••••••• •••••••••••••••••••••••• ••••••••••• 2-22
CL-1
CONTENTS
ROI-S04488
TITLE
PAGE
2.6
Receive Line Equalization•••••••••••••••••••••••••••••••••••• 2-22
2.6.1
Demultiplexing •••••••••••••••••••••••••••••••••••••••••••••••••• 2-22
2.6.2
Unipolar-to-Bipolar Code Conversion •••••••••••••••••••• 2-22
2.7
Analog Service Channel Signal Transmission (Optional) ••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 2-23
2.7.1
ASC Transmit Side••••••••••••••••••••••••••••••••••••••••••••• 2-23
2.7.2
ASC Receive Side •••••••••••••••••••••••••••••••••••••••••••••• 2-23
2.8
9.6 K Digital Service Channel Transmission •••••••••••• 2-23
2.8.1
DSC Transmit Side••••••••••••••••••••••••••••••••••••••••••••• 2-24
2.8.2
DSC Receive Side •••••••••••••••••••••••••••••••••••••••••••••• 2-24
2.9
Alarm Signal Transmission•••••••••••••••••••••••••••••••••• 2-24
2.10
Wayside Signal Transmission (Optional) •••••••••••••••• 2-24
2.10.1 WS Transmit Side •••••••••••••••••••••••••••••••••••••••••••••• 2-24 2.10.2 WS Receive Side•••••••••••••••••••••••••••••••••••••••••••••••• 2-24 2.11
64 K Digital Service Channel Transmission••••••••••••• 2-25
2.11.1 Service Channel Transmission of G.703 Codirectional •••••••••••••••••••••••••••••••••••••••••••••••••••• 2-25 2.11.2 Service Channel Transmission of V.11 ••••••••••••••••••• 2-25 2.12
LAN Signal Transmission (Optional)•••••••••••••••••••••• 2-26
2.12.1 Transmit Side •••••••••••••••••••••••••••••••••••••••••••••••••••• 2-26 2.12.2 Receive Side ••••••••••••••••••••••••••••••••••••••••••••••••••••• 2-26 2.13 3
CL-2
Alarm and Control Functions ••••••••••••••••••••••••••••••• 2-27 OPERATION •••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 3-1
3.1
Interface Terminals and Jacks••••••••••••••••••••••••••••••• 3-1
3.2
Controls, Indicators and Test Jacks •••••••••••••••••••••• 3-29
3.2.1
75 ohms/120 ohms Impedance Switch ••••••••••••••••••• 3-34
3.3
Equipment Start-up and Shut-down••••••••••••••••••••••• 3-37
3.3.1
Start-up•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 3-37
3.3.2
Shut-down •••••••••••••••••••••••••••••••••••••••••••••••••••••••• 3-38
3.4
Equipment Setting and Monitoring •••••••••••••••••••••••• 3-39
3.4.1
Setting Procedure from LCT••••••••••••••••••••••••••••••••• 3-40
3.4.2
Alarm/Status Monitoring Procedure from LCT ••••••••• 3-62
3.4.3
Monitoring Voltage of the ODU ••••••••••••••••••••••••••••• 3-70
CONTENTS
ROI-S04488
TITLE 4
PAGE
MAINTENANCE•••••••••••••••••••••••••••••••••••••••••••••••••••••• 4-1
4.1
Precautions ••••••••••••••••••••••••••••••••••••••••••••••••••••••• 4-1
4.2
Maintenance Control from LCT •••••••••••••••••••••••••••••• 4-3
4.3
Test Equipment and Accessories•••••••••••••••••••••••••• 4-12
4.4
Periodic Maintenance ••••••••••••••••••••••••••••••••••••••••• 4-12
4.5
Corrective Maintenance •••••••••••••••••••••••••••••••••••••• 4-13
4.5.1
Fault Isolation Flow Chart•••••••••••••••••••••••••••••••••••• 4-13
4.5.2
Replacement••••••••••••••••••••••••••••••••••••••••••••••••••••• 4-19
4.5.3
Alignment••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 4-23
CL-3
CONTENTS
ROI-S04488
(This page is intentionally left blank.)
CL-4 4 pages
GENERAL
ROI-S04488
1. GENERAL This section provides information on the equipment composition and equipment performance of the MDP-( )MB-( ) Modulator-Demodulator (Indoor Unit (IDU)) equipment. This manual is applied to the F/W version 2.xx. The IDU has the following two types for each 1+0 and 1+1 systems. • Fixed bit rate type (for 4 × 2MB and optional 2 × 10/100 BASET(X)) • Free bit rate type (for 2/4/8/16 × 2MB and optional 2 × 10/100 BASE-T(X)) Front view of the IDUs are shown in Fig. 1-1, Fig. 1-2 (1/2) and Fig. 1-2 (2/2).
1-1
GENERAL
ROI-S04488
1.1 Equipment Composition The equipment composition is shown in Fig. 1-3 and Fig. 1-4.
1
4
BOTTOM LAYER 8
7
5 10
9
6 2
3
TOP LAYER
Note: The module 8 can not be mounted if module 5 and/or 7 are mounted.
Fig. 1-3 Component Module Arrangement for the IDU in 1+0 System (1/2)
1-5
GENERAL
ROI-S04488
MDP-[ ]MB-[ ] (IDU) *1 No.
H0091
MODULE NAME
REMARKS
H0091A/J H0091L H0091M H0091N H0091F/H/K H0091P 4x2MB 4x2MB 4x2MB 2/4/8x2MB 2/4/8/16x2MB 2/4/8/16x2MB H0092A/M/WMAIN BOARD
−
H0092D/N/X MAIN BOARD
−
−
−
−
−
−
−
−
−
−
−
−
− −
−
H2003A
MAIN BOARD
−
H2003B
MAIN BOARD
H2003D
MAIN BOARD
− −
H0093A
FRONT BOARD1
H0093G
FRONT BOARD1
H2004A
FRONT BOARD1
H2004B
FRONT BOARD1
H0095A
FRONT BOARD2
H0095D
FRONT BOARD2
X0581A/B
DC-DC CONV
H0174A
ASC INTFC
VF x 2 CH
H0175A
DSC INTFC
RS232/RS422 x 2 CH
H0176A
ALM INTFC
Cluster ALM x 2CH
H0172A
64K INTFC
G.703
H0173A
64K INTFC
V11
7
H0171A
WS INTFC
8
H0177A
SC LAN INTFC
H0098B
LAN INTFC
1
2
3 4 5
6
9 10
− −
− −
−
−
−
−
−
− −
− −
−
− −
− −
−
−
− −
−
−
−
−
− − −
−
75 ohms BNC
−
−
75 ohms BNC 75/120 ohms
−
−
−
75/120 ohms
2 MB x 1CH 2 M/80Kbps
−
−
10/100BASE-T(X) x 2CH
G5440B/F/G PM CARD
Serial
G8896B
Ether
PM CARD
Note:
: Mounted : Optional − : Not applicable *1 : H0091A/J/L/M H0091N H0091F/H/K/P
MDP-8MB-12A MDP-17MB-3A MDP-34MB-25C
Fig. 1-3 Component Module Arrangement for the IDU in 1+0 System (2/2)
1-6
GENERAL
ROI-S04488
U2 (MD Unit) U1 (SW Unit) U3 (MD Unit) IDU
1
3
2 MD Unit (U2/U3)
4
8
10
12
9 7 11
6
5 SW UNIT (U1)
Note: The module 12 can not be mounted if module 8 and/or 9 are mounted. Fig. 1-4 Component Module Arrangement for the IDU in 1+1 System (1/3)
1-7
GENERAL
ROI-S04488
MDP-[ ]MB-[ ] (IDU) *1 No.
H0161
UNIT/MODULE NAME
REMARKS
H0161A/J H0161L H0161M H0161N H0161F/H/K H0161P 4x2MB 4x2MB 4x2MB 2/4/8x2MB 2/4/8/16x2MB 2/4/8/16x2MB
U1
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
75 ohms BNC
−
−
75 ohms BNC
H01 64A/ D
SW UNI T
H0164C/E
SW UNIT
H0164F
SW UNIT
−
H0164G
SW UNIT
−
−
H0164H
SW UNIT
−
−
−
H0164J
SW UNIT
−
−
−
−
H0163A/E/G MD UNIT
−
−
−
−
−
−
−
−
−
−
−
−
−
−
H01 63D/ H
MD UNIT
− −
MD UNIT
−
H0163K
MD UNIT
−
−
−
H0163L
MD UNIT
−
−
−
−
H0163A/E/G MD UNIT
−
−
−
−
−
−
−
−
−
−
−
−
−
−
U2 H0163J
H01 63D/ H
MD UNIT
− −
MD UNIT
−
H0163K
MD UNIT
−
−
−
H0163L
MD UNIT
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
U3 H0163J
H0092H/P/U MAIN BOARD H0092K/R/V MAIN BOARD
− −
1 H2003D
MAIN BOARD
−
H2003E
MAIN BOARD
−
−
−
H2003F
MAIN BOARD
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
2 H0093B
FRONT BOARD1
3 X0581A/B
DC-DC CONV
H00 94B /H
SW BOARD
H0094D/J
SW BOARD
−
−
4 H2005A
SW BOARD
−
H2005B
SW BOARD
−
−
−
H2005C
SW BOARD
−
−
−
Note:
: Mounted : Optional − : Not applicable *1 : H0161A/J/L/M H0161N H0161F/H/K/P
−
−
MDP-8MB-13A MDP-17MB-4A MDP-34MB-26C
Fig. 1-4 Component Module Arrangement for the IDU in 1+1 System (2/3)
1-8
GENERAL
ROI-S04488
MDP-[ ]MB-[ ] (IDU) *1 No.
H0161
UNIT/MODULE NAME
REMARKS
H0161A/J H0161L H0161M H0161N H0161F/H/K H0161P 4x2MB 4x2MB 4x2MB 2/4/8x2MB 2/4/8/16x2MB 2/4/8/16x2MB
−
−
−
−
−
−
−
−
−
−
75 ohms BNC
−
−
75 ohms BNC
H0093C
FRONT BOARD1
H0093H
FRONT BOARD1
−
H2004C
FRONT BOARD1
−
−
H2004D
FRONT BOARD1
−
−
−
H0095A
FRONT BOARD2
−
−
−
−
H0095D
FRONT BOARD2
−
−
H0172A
64K INTFC
G.703
H0173A
64K INTFC
V11
8 H0171A
WS INTFC
5
6
7
9
10 11
−
−
−
75/120 ohms
−
−
−
75/120 ohms
2 MB x 1CH
H0174A
ASC INTFC
VF x 2 CH
H0175A
DSC INTFC
RS232/RS422 x 2 CH
H0176A
ALM INTFC
Cluster ALM x 2CH
H0098B
LAN INTFC
−
−
10/100BASE-T(X) x 2CH
G5440B/F/G PM CARD
Serial
G8896B
PM CARD
Ether
SC LAN INTFC
2 M/80Kbps
12 H0177A
Note:
: Mounted : Optional − : Not applicable *1 : H0161A/J/L/M H0161N H0161F/H/K/P
MDP-8MB-13A MDP-17MB-4A MDP-34MB-26C
Fig. 1-4 Component Module Arrangement for the IDU in 1+1 System (3/3)
1-9
GENERAL
ROI-S04488
1.2 Equipment Performance The performance characteristics of the IDU are listed in Table 1-1. Table 1-1 Performance Characteristics of IDU
Data signal interface (between IDU and DTE) Bit rate:
2.048 Mbps ±50 ppm (2 x 2 MB/4 x 2 MB/8 x2 MB/ 16 x 2 MB system)
Level:
Meets specification of ITU-T G.703.
Code format:
High Density Bipolar-3 (HDB-3)
Impedance:
120 ohms, balanced or 75 ohms, unbalanced
Modulation method:
4-phase shift keying (4 PSK) system
Demodulation method:
Quasi-coherent detection
IF signal interface (between IDU and ODU) Signal frequency TX:
850 MHz
RX:
70 MHz
Signal level IF output:
−5 dBm, nominal
IF input:
−15 to 0 dBm (at, RX IN), varies with cable length (maximum cable length (8D-FB): L = 300m)
Impedance:
50 ohms, unbalanced
Orderwire frequency Output:
450 kHz, amplitude modulation (AM)
Input:
468 kHz, AM
Power supply:
−43 V DC (through) at IF IN/OUT
Control/Monitor signal frequency:
10 MHz, amplitude shift keying (ASK) (at IF IN/OUT)
Analog service channel (ASC) signal interface (optional) Frequency:
0.3 to 3.4 kHz
Impedance:
600 ohms, balanced
1-10
GENERAL
ROI-S04488
Table 1-1 Performance Characteristics of IDU (Cont’d)
Digital service channel (DSC) signal interface Bit rate:
• 9.6 kbps (asynchronous) • 64 kbps (G.703/V.11) (optional)
Level:
RS-232, RS-422, RS-485 (TERM) or RS-485 (NON TERM) Meet specifications of ITU-T G.703/V.11 (64k) Note: Depending on combination of optional module, both ASC and DSC cannot be used simultaneously.
Way Side (WS) signal interface (optional in 16 x 2 MB system) Bit rate:
2.048 Mbps
Interface:
HDB-3 (ITU-T G.703)
Impedance:
75 ohms or 120 ohms (selectable)
Local Area Network (LAN) signal interface (optional) Standards Compliance
IEEE 802.3 (10 BASE-T), IEEE 802.3u (100 BASE-TX), IEEE 802.3x (Flow control)
Network Port
10 Mbps/100 Mbps and Full/Half duplex Auto negotiation or Fixed
Total Port
2 (Each port is separated)
Flow Control
802.3x (Full Duplex), Back pressure (Half Duplex)
Forwarding Mode
Store-and -Forward
Transmission Length
Category 5, Max. 100 m
Transmission Rate (Port 1 and Port 2)
2 Mbps to 32 Mbps (selectable, depends on the system)
House Keeping Alarm Input/Output (optional) Output (Form-C):
Rated Current 0.2 A Maximum Voltage 100 V (AC+DC)
Input (Photo coupler):
Open > 200 kohms Closed < 50 ohms
Service channel (SC) Local Area Network (LAN) signal interface (optional) Standards Compliance
IEEE 802.3 (10 BASE-T)
Network Port
10 Mbps Half duplex Fixed
Total Port
1
Forwarding Mode
Store-and -Forward
Transmission Length
Category 5, Max. 100 m
Transmission Rate
80Kbps (in 2/4/8 x 2 MB) or 2Mbps(in 16 x 2 MB)
1-11
GENERAL
ROI-S04488
Table 1-1 Performance Characteristics of IDU (Cont’d)
Dimensions:
482 wide x 44 high x 240 deep (mm) for 1+0 482 wide x 132 high x 240 deep (mm) for 1+1
Weight:
Approx. 4 kg (including all options) for 1+0 Approx. 11 kg (including all options) for 1+1
Relative Humidity:
Less than 90% at +50°C (Non-condensing)
Environmental temperature range Operation:
−5°C to +50°C
Storage:
−30°C to +70°C
1-12 12 pages
ROI-S04488
FUNCTIONAL OPERATION
2. FUNCTIONAL OPERATION This section describes functional operation of the transmit line equalization, transmit digital processing, modulation, demodulation, receive digital processing, receive line equalization, analog service channel signal transmission, 9.6k digital service channel transmission, alarm signal transmission, wayside signal transmission, 64k digital service channel transmission, LAN signal transmission, and alarm and control in that order for the IDU. The IDU provides four signal transmission systems; 2 x 2 MB, 4 x 2 MB, 8 x 2 MB and 16 x 2 MB in 1+0 and 1+1 configuration as shown in Fig 21 and Fig 2-2 Functional Block Diagram.
2-1
FUNCTIONAL OPERATION
(This page is intentionally left blank.)
2-2
ROI-S04488
FUNCTIONAL OPERATION
ROI-S04488
INTFC (CH1 - CH4)
INPUT LOSS 1-2 AIS RCVD 1-2 FE LB CTRL 1-4
2 x 2 MB SYSTEM
CH1 IN
TRANS
CH2 IN
TRANS
CH1 OUT
TRANS
CH2 OUT
TRANS
PLS MON
AIS DET
LOOPBACK CKT
MEM
B-U CONV
LOOPBACK CKT
MEM
U-B CONV
AIS CTRL
MEM
AIS CTRL
MEM
a
FE LB ANS 1-4
b P-S CONV
OUTPUT LOSS 1-2 4 x 2 MB SYSTEM
MUX
PLS MON
CLK MON
TX CLK LOSS
INPUT LOSS 3-4
TX FPLS
CH3 IN
TRANS
CH4 IN
TRANS
CH3 OUT
TRANS
CH4 OUT
TRANS
PLS MON
AIS DET
w
TX CLK
AIS RCVD 3-4
x
TIM GEN LOOPBACK CKT
MEM
B-U CONV
LOOPBACK CKT
MEM
U-B CONV
AIS CTRL
MEM
AIS CTRL
MEM
z i
j S-P CONV DEMUX RX CLK
u
RX FPLS
v
CLK MON
PLS MON RX CLK LOSS
AIS CTRL
y
F SYNC ALM
OUTPUT LOSS 1-2 OUTPUT LOSS 3-4 AIS RCVD 1-2 INPUT LOSS 1-2 AIS RCVD 3-4 INPUT LOSS 3-4 FE LB CTRL 1-4 FE LB ANS 1-4 NE LB ANS 1-4
8 x 2 MB SYSTEM
FE LB CTRL 1-4 NE LB CTRL 1-4
CH5 IN CH6 IN CH5 OUT CH6 OUT CH7 IN CH8 IN CH7 OUT CH8 OUT
t From/To FIG. 2-1 (2/3)
P-S CONV
SERIAL ALM
S-P CONV
SERIAL DATA
q
r
c d
(CH5 - CH8)
k l
(SAME AS ABOVE)
CH9 IN CH10 IN CH9 OUT CH10 OUT CH11 IN CH12 IN CH11 OUT CH12 OUT 16 x 2 MB SYSTEM
s
16M CLK
1/8
e f
(CH9 - CH12)
m n
(SAME AS ABOVE)
CH13 IN CH14 IN CH13 OUT CH14 OUT CH15 IN CH16 IN CH15 OUT CH16 OUT
g h
(CH13 - CH16)
o p
Fig. 2-1 Fun ctio nal Block Diagram of IDU (1/3)
2-3/4
FUNCTIONAL OPERATION
ROI-S04488
DPU a b c d e f g h
w x
MOD P-S CONV
D-A CONV
SCRB DIF ENC
MUX
DIG FIL
PARITY CHECK
4PH MOD
IF IN/OUT
D-A CONV
DATA UP
MOD
PLS MON
TX FPLS TX CLK
TIM GEN
PLS MON
PCM CODEC
MST CLK MON
VCO
z
EOW
VCO 450 kHz CPU CLK
INTERFACE
TX DPU ALM
TERMINAL
WS/SC LAN INTFC* WS
MOD ALM
q
E
SERIAL ALM
H BER ALM
y
D
MUX ALM 1-4
L BER ALM
s
C
B-U CONV U-B CONV
(RJ45) From/To FIG. 2-1 (1/3)
B
EOW MOD
43 V DC
−
EOW IN
IN/OUT
A
EOW DEM
EOW OUT
H
DATA DOWN
DEM
F SYNC ALM
P-S CONV
F
S-P CONV
G
From/To FIG. 2-1 (3/3)
F SYNC ALM BER ALM
AIS CTRL
MOD CW AIS CTRL OFF r
SERIAL DATA BER THRESHOLD FRAME ID LAN INTFC*
10BASE-T/ 100BASE-TX
v t u
PORT1 PORT2
Ethernet SW SPEED CONV
F SYNC ALM
H
RX FPLS BER ALM
16M CLK RX CLK
BER DET
i j k l m n o p
S-P CONV
TIM GEN
OW/DSC/ASC IN
ASC/DSC/ALM INTFC
DEM A-D CONV
F SYNC
DIF DEC
Note: * Optional.
4 PH DEM
DEMUX DSCRB
I
A-D CONV
70 MHz
A-D CONV/LEV CONV
OUT DSC/64K/ ASC/EOW
IN OUT
B-U CONV U-B CONV 64K/SC LAN INTFC*
INTERFACE TERMINAL
Fig. 2-1 Fun ctio nal Block Diagram of IDU (2/3)
2-5/6
FUNCTIONAL OPERATION
ROI-S04488
DPU a b c d e f g h
w x
MOD P-S CONV
D-A CONV
SCRB DIF ENC
MUX
DIG FIL
4PH MOD
PARITY CHECK
IF IN/OUT
D-A CONV
DATA UP
MOD
PLS MON
TX FPLS
TIM GEN
TX CLK
PLS MON
DEM
VCO
z
EOW
VCO 450 kHz
EOW IN
CPU CLK INTERFACE
TX DPU ALM
TERMINAL
WS/SC LAN INTFC* WS
MOD ALM
C D E
B-U CONV U-B CONV
IN/OUT
(RJ45) From/To FIG. 2-1 (1/3)
B
EOW MOD
43 V DC
−
EOW OUT
H
A
EOW DEM
MST CLK MON
PCM CODEC
DATA DOWN
MUX ALM 1-4
SERIAL ALM
q
L BER ALM H BER ALM F SYNC ALM
s
F
S-P CONV
G
From/To FIG. 2-1 (3/3)
F SYNC ALM BER ALM
AIS CTRL
y
P-S CONV
MOD CW AIS CTRL OFF SERIAL DATA
r
BER THRESHOLD FRAME ID LAN INTFC* PORT1
10BASE-T/ 100BASE-TX
PORT2
Ethernet SW SPEED CONV
F SYNC ALM
H
RX FPLS
v
BER ALM
16M CLK
t
RX CLK
u
BER DET
i j k l m n o p
TIM GEN
S-P CONV
OW/DSC/ASC IN
DEM A-D CONV
F SYNC
Note: * Optional.
4 PH DEM
DEMUX DIF DEC
DSCRB
I
A-D CONV
ASC/DSC/ALM INTFC
70 MHz
A-D CONV/LEV CONV
OUT DSC/64K/ ASC/EOW
IN
B-U CONV U-B CONV
OUT
64K/SC LAN INTFC* INTERFACE TERMINAL
Fig. 2-1 Fun ctio nal Block Diagram of IDU (2/3)
2-5/6
FUNCTIONAL OPERATION
ROI-S04488
TX PWR ALM RX LEV ALM S-P CONV
APC 1 ALM APC 2 ALM IF INPUT ALM ODU
INPUT LOSS 1-16 S-P CONV
TX CLK LOSS RX CLK LOSS OUTPUT LOSS 1-16 DEM ALM H BER ALM IDU
D
TX DPU ALM BER ALM
I H E
F SYNC ALM INTERFACE TERMINAL
MOD ALM
NO
From/To FIG. 2-1 (2/3)
F
RL4
DPU SERIAL FE LB CTRL 1-16 S-P CONV
NE LB CTRL 1-16 AIS CTRL 1-16
B
MAINT
NC
MOD CW
DPU SERIAL G
A
COM
DATA UP
MAINT
CPU
DATA DOWN
CPU ALM CPU RESET
C
CPU CLK NO
INTERFACE TERMINAL
INTERFACE TERMINAL
RL1
COM
TX ALM
NC
PM CARD*
LA PORT CPU
PHOTOCOUPLERs
HOUSEKEEPING INPUT
NMS/RA NO RL2
RELAYs
COM
RX ALM
NC
HOUSEKEEPING OUTPUT
NO RL3
Notes: 1. *Optional.
COM
BER ALM
NC
2. Four relay contacts are outputed from interface terminal (ALM/ALM AUX). Plural alarms can be applied to a single relay. The figure shows the default settings. Refer to paragraph 3.4 for changing the settings. 3. Refer to the table 3.1 Interface Terminals and Jacks for the details of pin assignment for the alarm signals. Fig. 2-1 Functi onal Blo ck Diagram of IDU in 1+0 System (3/3)
2-7/8
FUNCTIONAL OPERATION
ROI-S04488
TX PWR ALM
S-P CONV
RX LEV ALM APC 1 ALM APC 2 ALM IF INPUT ALM ODU
INPUT LOSS 1-16 S-P CONV
TX CLK LOSS RX CLK LOSS OUTPUT LOSS 1-16 DEM ALM H BER ALM IDU
D
TX DPU ALM BER ALM
I H E
F SYNC ALM INTERFACE TERMINAL
MOD ALM
NO
From/To FIG. 2-1 (2/3)
F
RL4
DPU SERIAL FE LB CTRL 1-16 S-P CONV
NE LB CTRL 1-16 AIS CTRL 1-16
B
MAINT
NC
MOD CW
DPU SERIAL G
A
COM
DATA UP
MAINT
CPU
DATA DOWN
CPU ALM CPU RESET
C
CPU CLK NO
INTERFACE TERMINAL
RL1
INTERFACE TERMINAL
COM
TX ALM
NC
PM CARD*
LA PORT CPU
HOUSEKEEPING INPUT
PHOTOCOUPLERs
NMS/RA NO RL2
COM
RX ALM
NC
HOUSEKEEPING OUTPUT
RELAYs
NO RL3
Notes: 1. *Optional.
COM
BER ALM
NC
2. Four relay contacts are outputed from interface terminal (ALM/ALM AUX). Plural alarms can be applied to a single relay. The figure shows the default settings. Refer to paragraph 3.4 for changing the settings. 3. Refer to the table 3.1 Interface Terminals and Jacks for the details of pin assignment for the alarm signals. Fig. 2-1 Functi onal Blo ck Diagram of IDU in 1+0 System (3/3)
2-7/8
FUNCTIONAL OPERATION
ROI-S04488
INTFC SECTION (CH1 - CH4)
INPUT LOSS 1-2 AIS RCVD 1-2 FE LB CTRL 1-4 CH1 IN
2 × 2 MB SYSTEM
CH2 IN
PLS MON
AIS DET
LOOPBACK CKT
MEM
B-U CONV
LOOPBACK CKT
MEM
U-B CONV
AIS CTRL
MEM
AIS CTRL
MEM
a
FE LB ANS 1-4
b P-S CONV
CH1 OUT
CH2 OUT OUTPUT LOSS 1-2
MUX
PLS MON
4 × 2 MB SYSTEM
TX CLK LOSS
INPUT LOSS 3-4
CLK MON TX FPLS TX CLK
AIS RCVD 3-4
CH3 IN
CH4 IN
CH3 OUT
PLS MON
AIS DET
LOOPBACK CKT
MEM
B-U CONV
LOOPBACK CKT
MEM
U-B CONV
AIS CTRL
MEM
AIS CTRL
MEM
x
i
j
S-P CONV DEMUX RX CLK RX FPLS
CH4 OUT
w
u v
CLK MON
PLS MON RX CLK LOSS
AIS CTRL F SYNC ALM 12M CLK
1/8 OUTPUT LOSS 1-2 OUTPUT LOSS 3-4 AIS RCVD 1-2 INPUT LOSS 1-2 AIS RCVD 3-4 INPUT LOSS 3-4 FE LB CTRL 1-4 FE LB ANS 1-4 NE LB ANS 1-4
8 × 2 MB SYSTEM
FE LB CTRL 1-4 NE LB CTRL 1-4
CH5 IN CH6 IN CH5 OUT CH6 OUT CH7 IN CH8 IN CH7 OUT CH8 OUT CH9 IN CH10 IN CH9 OUT CH10 OUT CH11 IN CH12 IN CH11 OUT CH12 OUT 16 × 2 MB SYSTEM
CH13 IN CH14 IN CH13 OUT CH14 OUT CH15 IN CH16 IN CH15 OUT CH16 OUT
y s t FROM/TO FIG. 2-2 (2/4)
P-S CONV
SERIAL ALM
S-P CONV
SERIAL DATA
INTFC SECTION (CH5 - CH8)
q
r
c d k l
(SAME AS ABOVE)
INTFC SECTION (CH9 - CH12)
e f m n
(SAME AS ABOVE)
INTFC SECTION (CH13 - CH16) (SAME AS ABOVE)
g h o p
Fig. 2-2 Functi onal Blo ck Diagram of IDU in 1+1 System (1/4)
2-9/10
FUNCTIONAL OPERATION
ROI-S04488
INTFC SECTION (CH1 - CH4)
INPUT LOSS 1-2 AIS RCVD 1-2 FE LB CTRL 1-4 PLS MON
LOOPBACK CKT
MEM
B-U CONV
LOOPBACK CKT
MEM
U-B CONV
AIS CTRL
MEM
AIS CTRL
MEM
CH1 IN
2 × 2 MB SYSTEM
CH2 IN
AIS DET
a
FE LB ANS 1-4
b P-S CONV
CH1 OUT
CH2 OUT OUTPUT LOSS 1-2
MUX
PLS MON
4 × 2 MB SYSTEM
CLK MON
TX CLK LOSS
INPUT LOSS 3-4
TX FPLS
PLS MON
LOOPBACK CKT
MEM
B-U CONV
LOOPBACK CKT
MEM
U-B CONV
AIS CTRL
MEM
AIS CTRL
MEM
CH3 IN
CH4 IN
CH3 OUT
AIS DET
w
TX CLK
AIS RCVD 3-4
x
i
j
S-P CONV DEMUX RX CLK
u
RX FPLS
CH4 OUT
v
CLK MON
PLS MON RX CLK LOSS
AIS CTRL
y
F SYNC ALM
FE LB CTRL 1-4 NE LB CTRL 1-4
CH5 IN CH6 IN CH5 OUT CH6 OUT CH7 IN CH8 IN CH7 OUT CH8 OUT
t FROM/TO FIG. 2-2 (2/4)
OUTPUT LOSS 1-2 OUTPUT LOSS 3-4 AIS RCVD 1-2 INPUT LOSS 1-2 AIS RCVD 3-4 INPUT LOSS 3-4 FE LB CTRL 1-4 FE LB ANS 1-4 NE LB ANS 1-4
8 × 2 MB SYSTEM
P-S CONV
SERIAL ALM
S-P CONV
SERIAL DATA
q
r
c d
INTFC SECTION (CH5 - CH8)
k l
(SAME AS ABOVE)
CH9 IN CH10 IN CH9 OUT CH10 OUT CH11 IN CH12 IN CH11 OUT CH12 OUT 16 × 2 MB SYSTEM
s
12M CLK
1/8
e f
INTFC SECTION (CH9 - CH12)
m n
(SAME AS ABOVE)
CH13 IN CH14 IN CH13 OUT CH14 OUT CH15 IN CH16 IN CH15 OUT CH16 OUT
g h
INTFC SECTION (CH13 - CH16)
o p
(SAME AS ABOVE)
Fig. 2-2 Functi onal Blo ck Diagram of IDU in 1+1 System (1/4)
2-9/10
FUNCTIONAL OPERATION
ROI-S04488
From/To FIG. 2-2 (4/4) TX CLK LOSS 2
SW UNIT No. 1 MD UNIT
1
DPU
a
H
b
H
c
MDP P-S CONV
SCRB PARITY CHECK
H
From/To FIG. 2-2 (1/4)
H
e
H
f
H
g
H
h
H
TX FPLS TX CLK
DIG FIL
D-A CONV
MPX IF IN/OUT
4 PH MOD
D-A CONV PLS MON
PLS MON
d
DIF ENC
MUX
MOD DEM
850 MHz VCO
TIM GEN
B
EOW DEM
MST CLK MON
PCM CODEC
DATA UP A DATA DOWN
EOW MOD
–43 V DC
CLK MON
450 kHz
CPU CLK C TX DPU ALM D MOD ALM E
w RX SW
From/To FIG. 2-2 (1/4)
x
g
SERIAL ALM
s
F SYNC ALM
y
AIS CTRL
MUX ALM 1-4 SERIAL ALM L BER ALM H BER ALM
P-S CONV
SYS ALM
From/To FIG. 2-2 (3/4) F
F SYNC ALM BER ALM MOD CW AIS CTRL OFF
H
EOW IN/OUT
BER THRESHOLD RX SW
PORT1
ETHERNET SW
PORT2
SPEED CONV
SYS CTRL
DEM ALM
LAN INTFC * 10 BASE-T 100 BASE-TX
S-P CONV
G
FRAME ID
F SYNC ALM
H
BER ALM
RX FPLS 12M CLK
SW
RX CLK
BER DET
S-P CONV
TIM GEN
A-D CONV
F SYNC
4 PH DEM
DEMUX DSCRB
k
I J
DEM
i j
H
DIF DEC
A-D CONV 70 MHz
l m From/To FIG. 2-2 (1/4)
n o
RX SW/ HL SW
p
No. 2 MD UNIT
IF IN/OUT DATA UP
v
DATA DOWN CPU CLK
t
TX DPU ALM u
MOD ALM SYS ALM
WS/SC LAN
CLK MON
SYS CTRL
WS/SC LAN INTFC * IN
B-U CONV/DPU
OUT (RJ45)
H
U-B CONV/DPU
DEM ALM SW
F SYNC ALM
OW/DSC/ASC ASC/DSC/ALM INTFC * IN
A-D CONV/ LEV CONV
OUT
DSC/64K/ ASC/EOW
BER ALM H
K L M N O
From/To FIG. 2-2 (3/4)
P Q
R S T
(SAME AS ABOVE)
64K/SC LAN INTFC * IN
B-U CONV/DPU
OUT
U-B CONV/DPU
H
RX SW
From FIG. 2-2 (4/4)
6
RX SW CONT
To RX SW
4
3
RX CLK LOSS From/To FIG. 2-2 (4/4)
Note: * Optional. Fig. 2-2 Functi onal Blo ck Diagram of IDU in 1+1 System (2/4)
2-11/12
FUNCTIONAL OPERATION
ROI-S04488
From/To FIG. 2-2 (4/4) TX CLK LOSS 2
SW UNIT No. 1 MD UNIT
1
DPU
a
H
b
H
c
MDP P-S CONV
SCRB PARITY CHECK
H
From/To FIG. 2-2 (1/4)
H
e
H
f
H
g
H
h
H
TX FPLS TX CLK
DIG FIL
D-A CONV
MPX IF IN/OUT
4 PH MOD
D-A CONV PLS MON
PLS MON
d
DIF ENC
MUX
MOD DEM
850 MHz VCO
TIM GEN
B
EOW DEM
MST CLK MON
PCM CODEC
DATA UP A DATA DOWN
EOW MOD
–43 V DC
CLK MON
450 kHz
CPU CLK C TX DPU ALM D MOD ALM E
w RX SW
From/To FIG. 2-2 (1/4)
x
g
SERIAL ALM
s
F SYNC ALM
y
AIS CTRL
MUX ALM 1-4 SERIAL ALM L BER ALM H BER ALM
P-S CONV
SYS ALM
From/To FIG. 2-2 (3/4) F
F SYNC ALM BER ALM MOD CW AIS CTRL OFF
H
EOW IN/OUT
S-P CONV
BER THRESHOLD RX SW
DEM ALM
LAN INTFC * 10 BASE-T 100 BASE-TX
PORT1
ETHERNET SW
PORT2
SPEED CONV
SYS CTRL
G
FRAME ID
F SYNC ALM
H
BER ALM
RX FPLS 12M CLK
SW
RX CLK
BER DET
S-P CONV
TIM GEN
A-D CONV
F SYNC
4 PH DEM
DEMUX DSCRB
k
I J
DEM
i j
H
DIF DEC
A-D CONV 70 MHz
l m From/To FIG. 2-2 (1/4)
n RX SW/ HL SW
o p
No. 2 MD UNIT
IF IN/OUT DATA UP
v
DATA DOWN CPU CLK
t
TX DPU ALM u
MOD ALM SYS ALM
WS/SC LAN
CLK MON
SYS CTRL
WS/SC LAN INTFC * IN
H
B-U CONV/DPU
OUT (RJ45)
U-B CONV/DPU
DEM ALM SW
F SYNC ALM
OW/DSC/ASC ASC/DSC/ALM INTFC * IN OUT
DSC/64K/ ASC/EOW
BER ALM H
A-D CONV/ LEV CONV
K L M N O
From/To FIG. 2-2 (3/4)
P Q
R S T
(SAME AS ABOVE)
64K/SC LAN INTFC * IN
B-U CONV/DPU
OUT
U-B CONV/DPU
H
RX SW
From FIG. 2-2 (4/4)
6
To RX SW
RX SW CONT
4
3
RX CLK LOSS From/To FIG. 2-2 (4/4)
Note: * Optional. Fig. 2-2 Functi onal Blo ck Diagram of IDU in 1+1 System (2/4)
2-11/12
FUNCTIONAL OPERATION
ROI-S04488
From/To FIG. 2-2 (4/4)
5
F
ALM CTRL (No. 1 CH)
TX SW CTRL
INTFC SERIAL
From/To FIG. 2-2 (2/4)
FE LB CTRL R 1-4 FE LB ANS R 1-4 INPUT LOSS 1-4 AIS RCVD 1-4 NE LB ANS 1-4 TX IN CLK LOSS S/P RX IN CLK LOSS OUTPUT LOSS 1-4 AIS SEND 1-4 DEM ALM L BER ALM H BER ALM
TX PWR ALM ODU SERIAL
P/S CONV
RX LEV ALM APC 1 ALM
S-P CONV
APC 2 ALM ODU
IF INPUT ALM
DPU SERIAL
INPUT LOSS 1-16 AIS RCVD 1-4
J I a
BER ALM F SYNC ALM
TX IN CLK LOSS DPU SERIAL
TX 1 ALM A B C D
RX IN CLK LOSS
S-P CONV
OUTPUT LOSS 1-16 DEM ALM
DATA UP
L BER ALM DATA DOWN
CPU
CPU CLK TX DPU ALM
H BER ALM
IDU
CPU ALM
From/To FIG. 2-2 (2/4) H E G b
DEM ALM MOD ALM FE LB CTRL 1-16
DPU SERIAL
MOD CW NE LB CTRL 1-16 AIS CTRL 1-16
S-P CONV
RX 1 ALM FE LB CTRL To FIG. 2-2 (1/4)
r
SERIAL DATA
P/S CONV
NE LB CTRL
RESET
To FIG. 2-2 (4/4)
MAINT
S/P CONV P/S CONV
MAIN BOARD 1 SERIAL
c
INTERFACE TERMINAL
LA PORT HOUSEKEEPING INPUT
PHOTOCOUPLERs
NMS/RA CPU From FIG. 2-2 (4/4)
5
From/To FIG. 2-2 (2/4)
P T S
TX SW CTRL RELAYs
d
RX 2 ALM From/To FIG. 2-2 (1/4)
f
HOUSEKEEPING OUTPUT
PM CARD*
TX 2 ALM
From/To FIG. 2-2 (2/4)
e
INTFC SERIAL BER ALM F SYNC ALM
K L M N R O Q r
DATA UP DATA DOWN CPU CLK TX DPU ALM DEM ALM MOD ALM DPU SERIAL
ALM CTRL (No. 2 CH) (SAME AS ABOVE)
ODU
IDU
SERIAL DATA MAINT
MAIN BOARD 2 SERIAL
Fig. 2-2 Functi onal Blo ck Diagram of IDU in 1+1 System (3/4)
2-13/14
FUNCTIONAL OPERATION
ROI-S04488
From/To FIG. 2-2 (4/4)
5
F
ALM CTRL (No. 1 CH)
TX SW CTRL
INTFC SERIAL
From/To FIG. 2-2 (2/4)
FE LB CTRL R 1-4 FE LB ANS R 1-4 INPUT LOSS 1-4 AIS RCVD 1-4 NE LB ANS 1-4 TX IN CLK LOSS S/P RX IN CLK LOSS OUTPUT LOSS 1-4 AIS SEND 1-4 DEM ALM L BER ALM H BER ALM
TX PWR ALM ODU SERIAL
P/S CONV
RX LEV ALM APC 1 ALM
S-P CONV
APC 2 ALM ODU
IF INPUT ALM
DPU SERIAL
INPUT LOSS 1-16 AIS RCVD 1-4
J I a
BER ALM F SYNC ALM
TX IN CLK LOSS DPU SERIAL
TX 1 ALM A B C D
RX IN CLK LOSS
S-P CONV
OUTPUT LOSS 1-16 DEM ALM
DATA UP
L BER ALM DATA DOWN
CPU
CPU CLK TX DPU ALM
H BER ALM
IDU
CPU ALM
From/To FIG. 2-2 (2/4) H E G b
DEM ALM MOD ALM FE LB CTRL 1-16
DPU SERIAL
MOD CW NE LB CTRL 1-16 AIS CTRL 1-16
S-P CONV
RX 1 ALM FE LB CTRL To FIG. 2-2 (1/4)
r
SERIAL DATA
P/S CONV
NE LB CTRL
MAINT
S/P CONV RESET
To FIG. 2-2 (4/4)
P/S CONV
MAIN BOARD 1 SERIAL
c
INTERFACE TERMINAL
LA PORT HOUSEKEEPING INPUT
PHOTOCOUPLERs
NMS/RA CPU From FIG. 2-2 (4/4)
5
From/To FIG. 2-2 (2/4)
P T S
TX SW CTRL RELAYs
d
HOUSEKEEPING OUTPUT
PM CARD*
TX 2 ALM
From/To FIG. 2-2 (2/4)
e
INTFC SERIAL BER ALM F SYNC ALM
RX 2 ALM
K L M N R O Q r
From/To FIG. 2-2 (1/4)
DATA UP DATA DOWN CPU CLK TX DPU ALM DEM ALM MOD ALM DPU SERIAL
ALM CTRL (No. 2 CH)
ODU
(SAME AS ABOVE)
IDU
SERIAL DATA MAINT
MAIN BOARD 2 SERIAL
f
Fig. 2-2 Functi onal Blo ck Diagram of IDU in 1+1 System (3/4)
2-13/14
FUNCTIONAL OPERATION
ROI-S04488
From/To FIG. 2-2 (2/4)
a
To FIG. 2-2 (3/4)
5 2
3
S/P
APC 11 ALM APC 12 ALM RX LEV 1 ALM OPR 1 ALM F ASYNC 1 ALM DEM 1 ALM BER 1 ALM
RX SW CTRL RX CLK LOSS 2
RX 2 ALM
S/P
From/To FIG. 2-2 (3/4)
ALM CTRL (COMMON)
TX ALM 1
TX SW CTRL LOGIC
TX OPR 1
MOD 2 ALM TX DPU 2 ALM TX PWR 2 ALM APC 21 ALM APC 22 ALM IF INPUT 2 ALM OPR 2 ALM
RX CLK LOSS 1
RX 1 ALM
6 4
MOD 1 ALM TX DPU 1 ALM TX PWR 1 ALM APC 11 ALM APC 12 ALM IF INPUT 1 ALM OPR 1 ALM
TX SW CTRL TX CLK LOSS 2
S/P
From/To FIG. 2-2 (2/4)
e
S/P
TX 2 ALM
From FIG. 2-2 (2/4)
b
TX CLK LOSS 1
TX 1 ALM
From FIG. 2-2 (2/4)
d
1
TX OPR 2
TX ALM 2 OPR REL No. 1 No. 2 AUX ALM TERMINAL
No. 1 I OPR SEL AUTO I No. 2
RX ALM 1 RX SW CTRL LOGIC
RX OPR 1
APC 21 ALM APC 22 ALM RX LEV 2 ALM OPR 2 ALM F ASYNC 2 ALM DEM 2 ALM BER 2 ALM
RX OPR 2
RX ALM 2
ALM TERMINAL
TX PWR 1 ALM APC 11 ALM APC 12 ALM IF INPUT 1 ALM INPUT LOSS 1-4 MUX ALM 1 c
MAIN BOARD 1 SERIAL
S/P
RL 1
RL 2
RX LEV 1 ALM OUTPUT LOSS 1-4 H BER 1 ALM
RL 3
FE LB CTRL 1-4 MOD 1 CW NE LB CTRL 1-4 AIS CTRL S 1-4
RL 4
TX PWR 2 ALM APC 21 ALM APC 22 ALM IF INPUT 1 ALM INPUT LOSS 1-4
RL 5
MUX ALM 2 f
MAIN BOARD 2 SERIAL
S/P
RL 6
RX LEV 1 ALM OUTPUT LOSS 1-4 H BER 1 ALM RL 7
Notes : 1.
Eight relay contacts are outputed from interface terminal (ALM TERMINAL). Plural alarms can be applied to a single relay. The figure shows the default settings. Refer to paragraph 3.4 for changing the settings.
REMOTE CTRL IN
FE LB CTRL 1-4 MOD 1 CW NE LB CTRL 1-4 AIS CTRL S 1-4
RL 8
NO COM NC NO COM NC NO COM NC NO COM NC
NO COM NC NO COM NC No.2 COM No.1 No.2 COM No.1
TX ALM 1
TX ALM 2
RX ALM 1
RX ALM 2
BER ALM
MAINT ALM
TX SW OPR
RX SW OPR
MAINT
2. Refer to the table 3.2 for Interface Terminals and Jacks for the details of pin assignment for the alarm signals.
Fig. 2-2 Functi onal Bloc k Diagram of IDU in 1+1 System (4/4)
2-15/16
FUNCTIONAL OPERATION
ROI-S04488
From/To FIG. 2-2 (2/4)
a
To FIG. 2-2 (3/4)
5 2
3
S/P
APC 11 ALM APC 12 ALM RX LEV 1 ALM OPR 1 ALM F ASYNC 1 ALM DEM 1 ALM BER 1 ALM
RX SW CTRL RX CLK LOSS 2
RX 2 ALM
S/P
From/To FIG. 2-2 (3/4)
ALM CTRL (COMMON)
TX ALM 1
TX SW CTRL LOGIC
TX OPR 1
MOD 2 ALM TX DPU 2 ALM TX PWR 2 ALM APC 21 ALM APC 22 ALM IF INPUT 2 ALM OPR 2 ALM
RX CLK LOSS 1
RX 1 ALM
6 4
MOD 1 ALM TX DPU 1 ALM TX PWR 1 ALM APC 11 ALM APC 12 ALM IF INPUT 1 ALM OPR 1 ALM
TX SW CTRL TX CLK LOSS 2
S/P
From/To FIG. 2-2 (2/4)
e
S/P
TX 2 ALM
From FIG. 2-2 (2/4)
b
TX CLK LOSS 1
TX 1 ALM
From FIG. 2-2 (2/4)
d
1
TX OPR 2
TX ALM 2 OPR REL No. 1 No. 2
No. 1 I OPR SEL AUTO I No. 2
AUX ALM TERMINAL RX ALM 1
RX SW CTRL LOGIC
RX OPR 1
APC 21 ALM APC 22 ALM RX LEV 2 ALM OPR 2 ALM F ASYNC 2 ALM DEM 2 ALM BER 2 ALM
RX OPR 2
RX ALM 2
ALM TERMINAL
TX PWR 1 ALM APC 11 ALM APC 12 ALM IF INPUT 1 ALM INPUT LOSS 1-4 MUX ALM 1 c
MAIN BOARD 1 SERIAL
S/P
RL 1
RL 2
RX LEV 1 ALM OUTPUT LOSS 1-4 H BER 1 ALM
RL 3
FE LB CTRL 1-4 MOD 1 CW NE LB CTRL 1-4 AIS CTRL S 1-4
RL 4
TX PWR 2 ALM APC 21 ALM APC 22 ALM IF INPUT 1 ALM INPUT LOSS 1-4
RL 5
MUX ALM 2 f
MAIN BOARD 2 SERIAL
S/P
RL 6
RX LEV 1 ALM OUTPUT LOSS 1-4 H BER 1 ALM RL 7
Notes : 1.
Eight relay contacts are outputed from interface terminal (ALM TERMINAL). Plural alarms can be applied to a single relay. The figure shows the default settings. Refer to paragraph 3.4 for changing the settings.
REMOTE CTRL IN
FE LB CTRL 1-4 MOD 1 CW NE LB CTRL 1-4 AIS CTRL S 1-4
RL 8
NO COM NC NO COM NC NO COM NC NO COM NC
NO COM NC NO COM NC No.2 COM No.1 No.2 COM No.1
TX ALM 1
TX ALM 2
RX ALM 1
RX ALM 2
BER ALM
MAINT ALM
TX SW OPR
RX SW OPR
MAINT
2. Refer to the table 3.2 for Interface Terminals and Jacks for the details of pin assignment for the alarm signals.
Fig. 2-2 Functi onal Bloc k Diagram of IDU in 1+1 System (4/4)
2-15/16
FUNCTIONAL OPERATION
ROI-S04488
2.1
Transmit Line Equalization This section describes the bipolar-to-unipolar multiplexing and parallel-to-serial conversion.
2.1.1
code
conversion,
Bipolar-to-Unipolar Code Conversion The signals applied to the TRAFFIC IN terminal are (*) 2.048 Mbps data streams in a bipolar pulse format of the high density bipolar-3 (HDB-3) code. Each bipolar-coded data stream is converted into an NRZ unipolar data stream. Note: *2 MB × 2 system: two 2 MB × 4 system: four 2 MB × 8 system: eight 2 MB × 16 system: sixteen
2.1.2
Multiplexing To obtain time slots for multiplexing, the 2.048 Mbps × N data streams are written in to a buffer memory and read out with radio section clock having a time gap. The data streams having a time gap are sent to a multiplexer
FUNCTIONAL OPERATION
ROI-S04488
2.1
Transmit Line Equalization This section describes the bipolar-to-unipolar multiplexing and parallel-to-serial conversion.
2.1.1
code
conversion,
Bipolar-to-Unipolar Code Conversion The signals applied to the TRAFFIC IN terminal are (*) 2.048 Mbps data streams in a bipolar pulse format of the high density bipolar-3 (HDB-3) code. Each bipolar-coded data stream is converted into an NRZ unipolar data stream. Note: *2 MB × 2 system: two 2 MB × 4 system: four 2 MB × 8 system: eight 2 MB × 16 system: sixteen
2.1.2
Multiplexing To obtain time slots for multiplexing, the 2.048 Mbps × N data streams are written in to a buffer memory and read out with radio section clock having a time gap. The data streams having a time gap are sent to a multiplexer (MUX) circuit, here, alarm information, AIS RCVD, loopback control/ answer, alarm/control signals and stuff information bits, etc. are inserted into the location of the time gap.
2.1.3
Parallel-to-Serial Conversion The signal streams which are formatted in radio frame, are fed to the DPU circuit.
2.2
Transmit Digital Processing This section describes the multiplexing, scrambling and parity check.
2.2.1
Multiplexing The data streams having a time gap are sent to the MUX in which frame pattern, multiframe pattern, analog service channel (ASC), digital service channel (DSC), WS, LAN data signals and parity check bits are inserted into the respective locations of the time gap. The multiplexed data streams are fed to the SCRB circuit.
2-17
FUNCTIONAL OPERATION
2.2.2
ROI-S04488
Scrambling To smooth the RF spectrum and to restore the clock at the receiving end, the multiplexed data streams are scrambled with the 12th (for 4 x 2 MB) or 14th (for 2 x 2 MB, 8 x 2 MB and 16 x 2 MB,) pseudo random pattern generated by the timing generator (TIM GEN) so that the transmission mark ratio is 1/2. Then the scrambled data stream is sent to the differential encoder (DIFF ENCOD).
2.2.3
Parity Check For detecting the bit error at the receiving end, the parity check bits are calculated and multiplexed into the radio frame signal streams.
2.3
Modulation This section describes the differential encoding, 4-phase shift keying modulation and orderwire signal modulation.
2.3.1
Differential Encoding In the 4-phase shift keying modulation system, the demodulator phase may not coincide with the modulation signal of the opposite transmitting end which give raise to phase ambiguity. To avoid this, an absolute reference phase is needed between the transmitting and receiving ends. As shown in Table 2-1, the two independent data streams fed from the SCRB circuit are represented as an arrangement of Gray-coded binary digits. The two-bit Gray-coded data streams are then converted into pulse streams in natural binary code for facilitating differential encoding. Table 2-1 Binary Combinations DECIMAL
2-18
GRAY CODE
NATURAL BINARY CODE
0
0
0
0
0
1
0
1
0
1
2
1
1
1
0
3
1
0
1
1
FUNCTIONAL OPERATION
ROI-S04488
Table 2-2 shows typical operation of the differential encoding circuit. Phases in the natural-binary-coded pulse streams are accumulated in quaternary notation at every time slot. The data streams thus encoded are reconverted into pulse streams in gray code and then sent to a driver. Table 2-2 Typical Operation of Differential Encoding Circuit TIME SLOT NATURALBINARYCODED DATA
0*
1
2
3
4
5
6
7
8
9
10
11 ...
Data 1
0
1
1
1
0
1
0
1
0
1
0 ...
Data 2
1
1
0
0
0
0
1
1
0
1
1 ...
Quaternary
1
3
2
2
0
2
1
3
0
3
1 ...
+ ENCODED DATA
+
′′′′′′′′′′′′′′′
+
+
+
Quaternary
0
1
0
2
0
0
2
3
2
2
1
2 ...
Data 1
0
0
0
1
0
0
1
1
1
1
0
1 ...
Data 2
0
1
0
0
0
0
0
1
0
0
1
0 ...
Note: * Operating process given above assumes that the initial time slot is 0.
2.3.2
4-Phase Shift Keying Modulation To permit 4-phase shift keying modulation, the encoded data streams are converted into two separate two-level baseband signals for the P and Q channels by the digital-to-analog converter (D-A CONV) on the MOD section according to the logical status (see Fig. 2-3). To limit the associated transmitter output power spectrum, the voltage spectrum of the two-level baseband signal is shaped by each low-pass filter. The filtered signals are applied to a 4-phase modulator (4PH MOD). To obtain an 850 MHz IF carriers for 4PH MOD, an 850 MHz carrier is generated by the 850 MHz voltage controlled oscillator (VCO), and is split into two for the P and Q channels. The 850 MHz carrier for the Q channel is phase-shifted by π /2 from the P channel. The MOD modulates each of the 850 MHz carriers with a related twolevel baseband signal, and combines the modulated 850 MHz signals on the P and Q channels to arrange a four-phase assignment as shown in Fig. 2-2. The obtained 850 MHz IF signal is filtered by a LPF for eliminating the out-of-band components, amplified up to the required level by an automatic gain control (AGC) amplifier and sent to the ODU. Then, it is combined with 450 kHz amplitude-modulated engineering orderwire (EOW) signal and 10 MHz amplitude shift keying (ASK)-modulated control signal.
2-19
FUNCTIONAL OPERATION
ROI-S04488
3π/2 STATUS
P CHANNEL
Q CHANNEL
1(0)
-L
-L
2(π/2)
-L
+L
3(π)
+L
+L
4(3π/2)
+L
-L
P +L
-L
0
π
+L
-L
Q
π/2
Fig. 2-3 PSK Modulation
2.3.3
Orderwire Signal Modulation To facilitate an EOW between the IDU and ODU, the EOW signal is amplitude-modulated with the 450 kHz carrier by the orderwire modulator (EOW MOD) on the MOD section. The modulated EOW signal is filtered to eliminate higher out-of-band noise, amplified up to the required level and combined with the 850 MHz IF signal through a band-pass filter (BPF). This eliminates lower out-of-band noise, receiving IF signal (70 MHz), and an arrester (ARSR) protecting the equipment from harmful voltages caused by lightning.
2.4
Demodulation This section describes the EOW and alarm signal demodulation, main signal demodulation and differential decoding.
2.4.1
EOW and Alarm Signal Demodulation The received (RX) signal from the ODU contains a 70 MHz IF signal, 468 kHz amplitude-modulated EOW signal and 10 MHz ASK-modulated alarm (ALM) signal. The RX signal is branched into two separate signals; One is sent to the DEM section through the BPF which eliminates the transmitting IF, EOW and ALM signals, and the other goes through a BPF which eliminates the 70 MHz IF signal. The orderwire demodulator (EOW DEM) demodulates the 468 kHz amplitude-modulated EOW signal. The demodulated 10 MHz ASK alarm signal is sent to the CPU for further processing.
2-20
FUNCTIONAL OPERATION
ROI-S04488
2.4.2
Main Signal Demodulation The incoming 70 MHz IF signal is amplified up to the required level by an AGC amplifier and split into two separate signals for the P and Q channels and then fed to the mixer. In addition to the 70 MHz IF signals, two carriers having a phase difference of π/2 produced by the carrier recovery circuit, which consists of a carrier synchronizer, a 70 MHz oscillator, and a carrier splitter (π/2), are applied to the decision circuit. In the decision circuit, each 70 MHz IF signal is coherent-detected with the related carrier to represent the original baseband signal corresponding to the phase assignment (see Fig. 2-4).
π/2
CARR 1
0
π
CARR 2 3π/2
DETECTED OUTPUT
INPUT PHASE
P CHANNEL
Q CHANNEL
0
-1
-1
π/2
-1
+1
π
+1
+1
3π/2
+1
-1
Note: −1 is replaced by logic 0 and +1 by logic 1.
Fig. 2-4 Demodulation
The clock oscillator circuit generates a 38.383 MHz clock for the analogto-digital converter (A-D CONV) circuits. In the A-D CONV, two 38.383 Mbps data streams are regenerated with 38.383 MHz clock. Then the two re-generated 38.383 data streams enter the differential decoding (DIFF DECOD) circuit.
2.4.3
Differential Decoding The process of differential decoding is the reverse of the differential encoding at the transmitting end. In the natural binary-coded pulse streams, the phase of the time slot leading one bit before an incoming time slot is subtracted in quaternary notation from that of the incoming time slot. The decoded 38.383 Mbps data streams are sent to the frame synchronizer and descramblers on the DPU section of the MAIN BOARD for receive digital processing.
2-21
FUNCTIONAL OPERATION
2.5
ROI-S04488
Receive Digital Processing This section describes the frame synchronization, descrambling and demultiplexing.
2.5.1
Frame Synchronization FS bits which are multiplexed at the transmitting end are detected and comparing to establish the frame synchronizer.
2.5.2
Descrambling To recover original data streams from received data streams, descrambling is performed by using the same frame pattern as the transmitting end.
2.5.3
Demultiplexing The two descrambled data streams enter the demultiplexer (DEMUX). The DEMUX circuit extracts the frame pattern, multiframe pattern, ASC and DSC signal bits, etc. from overhead bits with a clock produced at the TIM GEN.
2.6
Receive Line Equalization This section describes the demultiplexing and unipolar-to-bipolar code conversion.
2.6.1
Demultiplexing From received data streams, the alarm information, AIS RCVD, loopback control/answer and stuff information bits, etc. are extracted by the Demultiplexer (DEMUX) circuit. Then, 2.048 Mbps x N unipolar data/ CLK signals are fed to the next U/B CONV circuit.
2.6.2
Unipolar-to-Bipolar Code Conversion To provide the associated DTE with the original data stream in bipolar pulse format, the unipolar-coded 2.048 Mbps data streams are converted into 2.048 Mbps data streams in the specified bipolar pulse format (HDB3) by the U-B CONV circuit on the INTFC section.
2-22
FUNCTIONAL OPERATION
ROI-S04488
2.7
Analog Service Channel Signal Transmission (Optional) An analog service channel (ASC) transmission is performed in the ASC INTFC section, which provides the pulse code modulation codec (PCM CODEC) and PCM decodec (PCM DECOD) circuits. The ASC transmission is described in accordance with transmission side and receive side, respectively.
2.7.1
ASC Transmit Side An analog signal applied to the ASC IN terminal is passed on to PCM CODEC circuit. An analog signal is converted into a 80 kbps (approx.) digital signal at the PCM CODEC circuit by 10 kHz (approx.) timing pulse and 80 kHz (approx.) clock signal received from the MAIN BOARD. The converted digital signal is fed to the MAIN BOARD.
2.7.2
ASC Receive Side The 80 kbps (approx.) digital signal received from the MAIN BOARD is applied to the PCM DECOD circuit. This 80 kbps (approx.) bps digital signal is converted into an analog signal by the 10 kHz (approx.) timing pulse and 80 kHz (approx.) clock signal, and then the analog signal is fed to the ASC OUT terminal.
2.8
9.6 K Digital Service Channel Transmission The 9.6 K digital service channel (DSC) transmission is explained in the following section: TRANSMISSION CHANNEL DSC 1 and DSC 2− MAIN BOARD
2-23
FUNCTIONAL OPERATION
2.8.1
ROI-S04488
DSC Transmit Side The DSC signal received from DSC IN terminal is applied to level converter circuit. Here, the DSC signal is converted into 9.6 K transistortransistor logic (TTL) level in the level converter and fed to the digital processing unit (DPU) circuit on the MAIN BOARD. In the DPU circuit, 9.6 K (TTL) signal is converted into 40 kbps (approx.) with 40 kHz (approx.) clock produced at the MAIN BOARD, and fed to the opposite station.
2.8.2
DSC Receive Side The 40 kbps (approx.) extracted from DPU circuit on the MAIN BOARD is converted into 9.6 K (TTL) signal with 9.6 kHz clock. The 9.6 K (TTL) signal is converted into 9.6 K DSC si gnal in the level converter, and fed to the DSC OUT terminal.
2.9
Alarm Signal Transmission With optional ALM INTFC card, two channels cluster alarm transmission provides for external/internal alarm signal extension.
2.10 Wayside Signal Transmission (Optional) The wayside (WS) signal transmission is performed in the WS INTFC section.
2.10.1 WS Transmit Side The 2.048 Mbps bipolar signal applied through the WS IN terminal is fed to the bipolar-unipolar converter (B-U CONV) circuit, where it is converted into a NRZ unipolar signal. NRZ unipolar signal is codeconverted by the HDB-3 decoder. The code-converted 2.048 Mbps WS data signal is fed to the MAIN BOARD together with the clock.
2.10.2 WS Receive Side The process of RX side is the reverse of the process of the TX side. The 2.048 Mbps WS data signal and clock are applied to the HDB-3 encoder. In the HDB-3 encoder, 2.048 Mbps WS signal is code-converted and fed to unipolar-bipolar converter (U-B CONV). The 2.048 Mbps unipolar data signal is converted into the 2.048 Mbps bipolar data stream and fed to the WS OUT terminal.
2-24
FUNCTIONAL OPERATION
ROI-S04488
2.11 64 K Digital Service Channel Transmission Two types of transmission are provided for the service channel: codirectional transmission conforming to ITU-T G.703 and transmission conforming to V.11. Each transmission scheme corresponds to the type of 64K INTFC section.
2.11.1 Service Channel Transmission of G.703 Codirectional (a)
TX Side A 64 kbps bipolar signal is applied to the 64K INTFC section, t hen converted to a unipolar signal by the B-U CONV circuit. The unipolar signal is then code-converted with a decoder. The codeconverted signal is stuff-synchronized with 80 kHz (approx.) clock, then converted into a radio transmission format. After conversion, a 80 kbps (approx.) data signal is fed to the MAIN BOARD.
(b) RX Side The process of RX side is the reverse of the process of the TX side. A 80 kbps (approx.) data signal and the 80 kHz (approx.) clock signal from the MAIN BOARD are entered in the synchronizer circuit for the frame synchronization. The frame synchronized data signal is de-stuffed and converted into 64 kbps data signal. The resulting 64 kbps data signal is code-converted into G.703 signal with an encoder circuit, then converted again with the unipolar bipolar converter (U-B CONV) circuit into a 64 kbps bipolar data signal which is transmitted to the output terminal.
2.11.2 Service Channel Transmission of V.11 (a)
TX Side The 64 kbps (approx.) unipolar data signal and the 64 kHz (approx.) clock signal are entered into 64K INTFC section. The 64 kbps unipolar data signal undergoes stuff-synchronization with the 80 kHz (approx.) clock signal, then is converted into a format for the radio transmission and fed to the MAIN BOARD as a 80 kbps (approx.) data signal.
(b) RX Side The process of RX side is the reverse of the process of the TX side. The 80 kbps (approx.) unipolar data signal from the MAIN BOARD and the 80 kHz (approx.) clock signal are entered into 64K INTFC section. The data signal then is frame synchronized with the frame synchronizer circuit, then de-stuffed converted into a 64 kbps unipolar data signal with a 64 kHz clock signal, and is fed to the output terminal.
2-25
FUNCTIONAL OPERATION
ROI-S04488
2.12 LAN Signal Transmission (Optional) When the LAN INTFC module is used. The data signal for LAN (10BASE-T or 100BASE-TX) transmission is performed in the LAN INTFC module. Radio section throughput is selectable for each port. When 2 Mbps throughput is selected, ITU-T G.704 framing mode setting is available. When the SC LAN INTFC module is used. LAN Signal Transmission which used WS and the DSC transmission way (Optional).The data signal for LAN(10BASE-T) transmission is performed in the SC LAN INTFC module. A throughput is decided by data transmission capacity of equipment. When data transmission capacity is 16x2MB, it is set to about 2 Mbps, and it is set to about 80 kbps when other.
2.12.1 Transmit Side When the LAN INTFC module is used. The data signal applied through the LAN PORT1 and/or PORT2 terminals is fed to the LAN signal Switch Circuit which selects 10BASE-T or 100 BASE-TX. The data signal is converted to HDLC like frame for radio transmission and multiplexed with specified frame in the main data signal. When the SC LAN INTFC module is used. The data signal applied through the WS/SC LAN terminal. The data signal is converted to HDLC like frame for radio transmission and multiplexed with specified frame in the main data signal.
2.12.2 Receive Side When the LAN INTFC module is used. The data signal for LAN network is extracted from the main data signal. This data signal is performed HDLC like frame detection and fed to the LAN signal switch. The data signal from the LAN signal switch is output through the LAN PORT1 and/or PORT2 terminals. Note: The switching of data between PORT1 and PORT2 is not available. When the SC LAN INTFC module is used. The data signal for LAN network is extracted from the main data signal. This data signal is performed HDLC like frame detection and fed to the LAN signal switch. The data signal from the LAN signal switch is output through the WS/SC LAN terminal.
2-26
FUNCTIONAL OPERATION
ROI-S04488
2.13 Alarm and Control Functions Alarm and control functions of the IDU are described herein. Fault detection circuits are provided in the IDU, sending signals to give alarm indications and remote alarm reports (see Fig. 2-1, Fig. 2-2 and Table 2-3). The alarm signals initiated by detection circuits in the ODU are also sent to the IDU. Therefore, the total alarm indications for the IDU and ODU are provided by the IDU and ODU indicators on the IDU. When the equipment is operating normally, these indicators on the IDU stay unlit. When an abnormal condition occurs in the IDU (except power supply failure), the IDU indicator lights and a remote alarm report is made. The same applies for the ODU indicator. To monitor/control the alarm and status of IDU/ODU, PM CARD module communicates with pasolink network management system (PNMS) or pasolink network management terminal (PNMT) via RS-232C (19.2 kbps). The PM CARD (Pasolink Management Card) provides the following functions: • Communication with PNMS and PNMT • Communication with ALM CONT of the IDU • Communication with opposite PM CARD • Data collection of performance monitor • Forward input housekeeping alarm signals to PNMS or PNMT • Outputs of dry contact by control from PNMS or PNMT
2-27
FUNCTIONAL OPERATION
ROI-S04488
The PM CARD collects up to 300 items of events and performance information from IDU and ODU, and stores performance information for up to eight days. Notes in the Table 2-3 are as follows. Notes:*1. These alarms are initial value condition (for setting method, refer to paragraph 3.4.2 in this Section III). * 2. The alarm indication depends on system requirement (for setting method, refer to paragraph 3.4.2 in this Section III). * 3. The WS alarm indications can be inhibited. The WS alarm items are masked when the WS is not provided. 1. In an alarm condition, when the equipment is set to maintenance condition, the TX ALM, RX ALM and BER ALM for remote reporting are disabled. 2. When the IF cable between the IDU and ODU is electric short circuit condition or open condition, the IDU and ODU ALM LEDs are synchronously flashing.
2-28
FUNCTIONAL OPERATION
(This page is intentionally left blank.)
ROI-S04488
FUNCTIONAL OPERATION
(This page is intentionally left blank.)
2-30 30 pages
ROI-S04488
OPERATION
ROI-S04488
3. OPERATION This section provides instructions for operation of the IDU. Included is information on the interface terminals, interface jacks, controls, indicators, test jacks, equipment start-up and equipment shut-down.
3.1 Interface Terminals and Jacks The IDU has interface terminals and jacks to interconnect data signals, alarm, IF signals and line power with the associated equipment. These interface terminals and jacks are located on front of the equipment as shown in Fig. 3-1 and Fig. 3-2. The details of terminals and jacks for signal interface are described in Table 3-1 and Table 3-2. Caution: In back -to-back connection, the interface conditions of the PM CARD must be matched between two IDUs. Then, check the setting of the interface if it is RS-485 or RS-232C before connecting the cable. TRAFFIC IN/OUT (CH9 to CH16)
EOW 100M
IF IN/OUT
100M
PORT1 PORT2
CALL
PASOLINK ODU IDU
RESET PWR
MAINT
WS/SC LAN NMS LAN
FUSE (7.5A) +
−
TRAFFIC IN/OUT (CH1 to CH8)
ALM/AUX ALM
NMS/RA
OW/DSC/ASC
SELV
LA PORT
With LAN option TRAFFIC IN/OUT (CH9 to CH16)
EOW
IF IN/OUT
CALL
PASOLINK ODU IDU
RESET PWR
MAINT
WS/SC LAN NMS LAN
FUSE (7.5A) +
−
TRAFFIC IN/OUT (CH1 to CH8)
ALM/AUX ALM
NMS/RA
OW/DSC/ASC
SELV
LA PORT
Without LAN option TRAFFIC OUT
TRAFFIC IN IF IN/ OUT
CH1
CH2
CH3
CH4
CH1
CH2
CH3
EOW CH4
CALL
PASOLINK ODU IDU
RESET PWR
MAINT
SC LAN NMS LAN FUSE (7.5A)
+
−
TRAFFIC IN/OUT (CH1 to CH4)
ALM/AUX ALM
NMS/RA
OW/DSC/ASC
SELV
LA PORT
With BNC Interface Connector (For 4 CH)
TRAFFIC OUT
TRAFFIC IN IF IN/ OUT
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH1
CH2
CH3
CH4
CH5
EOW CH6
CH7
CH8
SC LAN NMS LAN
CALL
PASOLINK ODU IDU
RESET PWR
MAINT
FUSE (7.5A) +
−
TRAFFIC IN/OUT (CH1 to CH8)
ALM/AUX ALM
OW/DSC/ASC
NMS/RA
LA PORT
SELV
With BNC Interface Connector (For 8 CH) IDU Fig. 3-1 Front View of the IDU for Interface Connectors and Jacks in 1+0 System
3-1
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (1/12) Terminal
Description
IDU TRAFFIC IN/OUT (CH 1 to CH 8) (D-sub Connector, 37 Pins)
2.048 Mbps HDB-3 coded data input/output from/to D TE (CH 1 to CH 8), (Selectable 120-ohm, balanced/75-ohm, unbalanced)
Pins 1 (+) and 2 (−)
CH8 data input
Pins 3 (+) and 4 (−)
CH7 data input
Pins 6 (+) and 7 (−)
CH6 data input
Pins 8 (+) and 9 (−)
CH5 data input
Pins 11 (+) and 12 (−)
CH4 data input
Pins 13 (+) and 14 (−)
CH3 data input
Pins 16 (+) and 17 (−)
CH2 data input
Pins 18 (+) and 19 (−)
CH1 data input
Pins 20 (+) and 21 (−)
CH8 data output
Pins 22 (+) and 23 (−)
CH7 data output
Pins 25 (+) and 26 (−)
CH6 data output
Pins 27 (+) and 28 (−)
CH5 data output
Pins 29 (+) and 30 (−)
CH4 data output
Pins 31 (+) and 32 (−)
CH3 data output
Pins 34 (+) and 35 (−)
CH2 data output
Pins 36 (+) and 37 (−)
CH1 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN/OUT (CH 9 to CH 16) (D-sub Connector, 37 Pins)
2.048 Mbps HDB-3 coded data input/output from/to D TE (CH 9 to CH 16) (Selectable 120-ohm, balanced/75-ohm, unbalanced) (for 16 x 2 MB system only)
Pins 1 (+) and 2 (−)
CH16 data input
Pins 3 (+) and 4 (−)
CH15 data input
Pins 6 (+) and 7 (−)
CH14 data input
Pins 8 (+) and 9 (−)
CH13 data input
Pins 11 (+) and 12 (−)
CH12 data input
3-3
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (2/12) Terminal
Pins 13 (+) and 14 (−)
CH11 data input
Pins 16 (+) and 17 (−)
CH10 data input
Pins 18 (+) and 19 (−)
CH9 data input
Pins 20 (+) and 21 (−)
CH16 data output
Pins 22 (+) and 23 (−)
CH15 data output
Pins 25 (+) and 26 (−)
CH14 data output
Pins 27 (+) and 28 (−)
CH13 data output
Pins 29 (+) and 30 (−)
CH12 data output
Pins 31 (+) and 32 (−)
CH11 data output
Pins 34 (+) and 35 (−)
CH 10 data output
Pins 36 (+) and 37 (−)
CH 9 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN/OUT with BNC (CH 1 to CH 8) (D-sub Connector, 37 Pins)
3-4
Description
2.048 Mbps HDB-3 coded data input/output from/to D TE (CH 1 to CH 8) (for 2/4/8 x 2 MB system only) (Fixed 120ohm, balanced)
Pins 1 (+) and 2 (−)
CH8 data input
Pins 3 (+) and 4 (−)
CH7 data input
Pins 6 (+) and 7 (−)
CH6 data input
Pins 8 (+) and 9 (−)
CH5 data input
Pins 11 (+) and 12 (−)
CH4 data input
Pins 13 (+) and 14 (−)
CH3 data input
Pins 16 (+) and 17 (−)
CH2 data input
Pins 18 (+) and 19 (−)
CH1 data input
Pins 20 (+) and 21 (−)
CH8 data output
Pins 22 (+) and 23 (−)
CH7 data output
Pins 25 (+) and 26 (−)
CH6 data output
Pins 27 (+) and 28 (−)
CH5 data output
Pins 29 (+) and 30 (−)
CH4 data output
Pins 31 (+) and 32 (−)
CH3 data output
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (3/12) Terminal
Description
Pins 34 (+) and 35 (−)
CH2 data output
Pins 36 (+) and 37 (−)
CH1 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN 75 Ω (CH 1 to CH 8) (BNC, Female)
2.048 Mbps HDB3 coded data signal input from DTE (CH 1 to CH 8), (for 2/4/8 x 2 MB system only), (Fixed 75ohm, unbalanced)
CH1
BNC
CH1 data input
CH2
BNC
CH2 data input
CH3
BNC
CH3 data input
CH4
BNC
CH4 data input
CH5
BNC
CH5 data input
CH6
BNC
CH6 data input
CH7
BNC
CH7 data input
CH8
BNC
CH8 data input
TRAFFIC OUT 75 Ω (CH 1 to CH 8) (BNC, Female)
2.048 Mbps HDB3 coded data signal output to DTE (CH 1 to CH 8),(for 2/4/8 x 2 MB system only), (Fixed 75ohm, unbalanced)
CH1
BNC
CH1 data output
CH2
BNC
CH2 data output
CH3
BNC
CH3 data output
CH4
BNC
CH4 data output
CH5
BNC
CH5 data output
CH6
BNC
CH6 data output
CH7
BNC
CH7 data output
CH8
BNC
CH8 data output
3-5
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (4/12) Terminal
TRAFFIC IN/OUT with BNC (CH 1 to CH 4) (D-sub Connector, 37 Pins)
Description
2.048 Mbps HDB-3 coded data input/output from/to D TE (CH 1 to CH 4), (for 4 x 2 MB system only), (Fixed 120-ohm, balanced)
Pins 11 (+) and 12 (−)
CH4 data input
Pins 13 (+) and 14 (−)
CH3 data input
Pins 16 (+) and 17 (−)
CH2 data input
Pins 18 (+) and 19 (−)
CH1 data input
Pins 29 (+) and 30 (−)
CH4 data output
Pins 31 (+) and 32 (−)
CH3 data output
Pins 34 (+) and 35 (−)
CH2 data output
Pins 36 (+) and 37 (−)
CH1 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN 75 Ω (CH 1 to CH 4) (BNC, Female)
2.048 Mbps HDB3 coded data signal input from DTE (CH 1 to CH 4), (for 4 x 2 MB system only), (Fixed 75-ohm, unbalanced)
CH1
BNC
CH1 data input
CH2
BNC
CH2 data input
CH3
BNC
CH3 data input
CH4
BNC
CH4 data input
TRAFFIC OUT 75 Ω (CH 1 to CH 4) (BNC, Female)
2.048 Mbps HDB3 coded data signal output to DTE (CH 1 to CH 4), (for 4 x 2 MB system only), (Fixed 75-ohm, unbalanced),
CH1
BNC
CH1 data output
CH2
BNC
CH2 data output
CH3
BNC
CH3 data output
CH4
BNC
CH4 data output
3-6
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (5/12) Terminal
10/100BASE-T IN/OUT (Modular Connector RJ-45 8pins) (PORT1/PORT2)
Description
LAN signal input/output (optional) (MDI-X/MDI auto-sensing) MDI-X MDI
Pin 1
RD +
TD +
Pin 2
RD −
TD −
Pin 3
TD +
RD +
Pin 6
TD −
RD −
IF IN/OUT (N-P Connector)
TX IF signal output to ODU and RX IF signal input from ODU Caution: Do not connect other cables to this jack, because the −43 V DC power is superimposed on this jack. Danger: Do not touch the jack core before turning off power switch.
3-7
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (6/12) Terminal
Description
OW/DSC/ASC (D-sub Connector, 25 Pins)
Engineering orderwire (EOW), digital service channel (D SC), analog service channel (ASC) and ALARM signal input/ output
Pins 1 (+) and 2 (−)/
ASC1 input (VF) (optional), DSC 3 input (optional) or
Pins 1 and 2* 2
Alarm1*2 input (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 1 input (photocoupler) Normal signal in : Open Alarm signal in : Closed
Pins 3 (+) and 4 (−)/ Pins 3 and 4*
2
ASC2 input (VF) (optional), DSC 4 input (optional) or Alarm2*2 input (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 2 input (photocoupler) Normal signal in : Open Alarm signal in : Closed
Pins 5 (+) and 6 (−)
EOW input (VF)
Pins 7 (+) and 8 (−)
64 kHz clock input* 1
Pins 9 (+) and 10 (−)
DSC1 input (RS-232C, 64K (G.703)* 1 or 64K (V.11)* 1 )
Pins 11 (+) and 12 (−)
DSC2 input (RS-232C, RS-422 or RS-485)
Pins 14 (+) and 15 (−)/
ASC1 output (VF) (optional), DSC 3 output (optional) or
Pins 14 and 15*
2
Alarm1*2 output (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 1 output (relay contact) Normal signal out : Open Alarm signal out : Closed
Pins 16 (+) and 17 (−)/
ASC2 output (VF) (optional), DSC 4 output (optional) or
Pins 16 and 17* 2
Alarm2*2 output (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 2 output (relay contact) Normal signal out : Open Alarm signal out : Closed
3-8
Pins 18 (+) and 19 (−)
EOW output (VF)
Pins 20 (+) and 21 (−)
64 kHz clock output* 1
Pins 22 (+) and 23 (−)
DSC1 output (RS-232C, 64K (G.703)* 1 or 64K (V.11)* 1)
Pins 24 (+) and 25 (−)
DSC2 output (RS-232C, RS-422 or RS-485)
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (7/12) Terminal
Pin 13
Description
Ground Notes:1. *1 Optional 2. Both ASC and DSC 64K cannot be used simultaneously.
ALM/AUX ALM (D-sub Connector, 37 Pins) Pins 1 (COM), 2 (NO) and 3 (NC)
Alarm and transmission network surveillance auxiliary alarm input/output Transmitter alarm output* 3
Normal state Alarm state Pins 4 (COM), 5 (NO) and 6 (NC)
Between Pins 4 and 5 Open Closed
Between Pins 4 and 6 Closed Open
: :
BER alarm output when BER worse than 10 -6/10-5/10-4/10-3 (selectable)*3 Between Pins 20 and 21 Open Closed
Between Pins 20 and 22 Closed Open
Maintenance alarm output* 3 Between Pins 23 and 24 Normal state : Open Alarm state : Closed
Between Pins 23 and 25 Closed Open
Normal state Alarm state Pins 23 (COM), 24 (NO) and 25 (NC)
Between Pins 1 and 3 Closed Open
Receiver alarm output* 3
Normal state Alarm state Pins 20 (COM), 21 (NO) and 22 (NC)
: :
Between Pins 1 and 2 Open Closed
: :
Note:*3 The BER threshold values and alarm items are set in factory (default). To change the setting of alarm items by the PC, refer to Section 3.4.1 “Alarm Table” of this Manual. (Housekeeping alarm input through optional PM CARD.) Pin 7
Input 11
Pin 8 (G)
Input 12
Pin 9
Input 21
Pin 10 (G)
Input 22
3-9
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (8/12) Terminal
3-10
Description
Pin 11
Input 31
Pin 12 (G)
Input 32
Pin 13
Input 41
Pin 14 (G)
Input 42
Pin 15
Input 51
Pin 16 (G)
Input 52
Pin 17
Input 61
Pin 18 (G)
Input 62 (Housekeeping control output through optional PM CARD.)
Pin 26
Output 11
Pin 27
Output 12
Pin 28
Output 21
Pin 29
Output 22
Pin 30
Output 31
Pin 31
Output 32
Pin 32
Output 41
Pin 33
Output 42
Pin 19
Ground
Pins 34 and 35
Not Used Note: Input[ ] indicates the input of housekeeping alarm. The figure means that same order of tens makes the same pair e.g. 11/12 forms a pair. IDU side interface uses that of photo-coupler, the photo-coupler turns ON if pair elements contact with each other. Output[ ] indicates the output of housekeeping alarm. Figure means the same as in the Input. IDU side output uses the relay contact interface.
Pin 36
Input terminal of buzzer signal Note: In back-to-back station, the buzzer information transmits to the next station.
Pin 37
Output terminal of buzzer signal Note: In back-to-back station, the buzzer information transmits to the next station.
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (9/12) Terminal
NMS/RA (D-sub Connector, 15 Pins)
Description
Network management system (NMS) data input/output or remote access (RA) data input/output Note: When the PM CARD is not mounted on the equipment, this connector is used for Remote Access. PM CARD
RA
Pin 1
Party alarm management system (PAMS) TXD
RA TXD
Pin 2
EMS TXD/TXD+
RA GND
Pin 3
EMS RXD/TXD−
RA RXD
Pin 4
EMS TXDR
RA RTS
Pin 5
EMS TRS/RXD+
RA CTS
Pin 6
EMS CTS/RXD−
Pin 7
Ground
Pin 9
PAMS RXD
Pin 10
NMS TXD/TXD+
Pin 11
NMS RXD/TXD−
Pin 12
NMS TXDR
Pin 13
NMS RTS/RXD+
Pin 14
NMS CTS/RXD−
LA PORT (D-sub Connector, 15 pin)
Control/monitoring signal input/output from/to personal computer
Pin 1
TXD
Pin 3
RXD
Pin 4
RTS
Pin 5
CTS
Pin 11
LOCAL CTS
Pin 12
LOCAL RTS
Pin 13
LOCAL RXD
Pin 15
LOCAL TXD
Pins 2, 8 and 14
Ground
3-11
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (10/12) Terminal
NMS LAN (RJ45 8 pins)
Description
Network management station (PNMS) data input/output
Pin 1
LAN PNMS TX+
Pin 2
LAN PNMS TX−
Pin 3
LAN PNMS RX+
Pin 6
LAN PNMS RX−
WS /SC LAN (RJ45 8 pins)
Way side signal input/output For 120 ohms balanced interface
Pin 1
WS OUT (+)
Pin 2
WS OUT (−)
Pin 3
Reserved for SC LAN INTFC
Pin 4
WS IN (+)
Pin 5
WS IN (−)
Pin 6
Reserved for SC LAN INTFC
Pin 7
open
Pin 8
Frame ground (G) For 75 ohms unbalanced interface
3-12
Pin 1
WS OUT
Pin 2
Reserved for WS INTFC (120 ohms balance)
Pin 3
Reserved for SC LAN INTFC
Pin 4
WS IN
Pin 5
Reserved for WS INTFC (120 ohms balance)
Pin 6
Reserved for SC LAN INTFC
Pin 7
open
Pin 8
WS IN/OUT (G)
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (11/12) Terminal
Description
Do not connect any cable to the "Reserved" pins. Note: Available if WS INTFC is equipped. Disable when SC LAN INTFC is equipped. When WS signal is connected between two IDUs, perform wiring as follows.
IDU B WS/SC LAN (RJ45)
IDU A WS/SC LAN (RJ45) WS (120 ohms) 1 2 3 4 5 6 7 8
IDU B WS/SC LAN (RJ45)
IDU A WS/SC LAN (RJ45) WS (75 ohms) 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3-13
OPERATION
ROI-S04488
Table 3-1 Interface Terminals and Jacks in 1+0 system (12/12) Terminal
Description
WS /SC LAN (RJ45 8 pins)
DSC data for LAN
Pin 1
LAN DSC TX+
Pin 2
LAN DSC TX−
Pin 3
LAN DSC RX+
Pin 4
Reserved for WS INTFC
Pin 5
Reserved for WS INTFC
Pin 6
LAN DSC RX−
Pin 7
open
Pin 8
open Note: Available when SC LAN INTFC is equipped. Disabled when ALM INTFC, ASC INTFC, DSC INTFC 64K or WS INTFC (in case of 16x2MB) is used. Do not connect any cable to the "Reserved" pins. When SC LAN signal is connected between two IDUs, perform wiring as follows. IDU B WS/SC LAN (RJ45)
IDU A WS/SC LAN (RJ45) 1 2 3 4 5 6 7 8
SEL V (LINE IN) (Molex M5557-4R Connector, 4 Pins)
FG
3-14
SCLAN INTFC
1 2 3 4 5 6 7 8
−20 V to −60 V/+20 V to +60 V DC power input Note: The range of DC power input depends on system requirement.
Pin 1
0 V*4 (or +48 V* 5)
Pin 2
−48 V*4 (or 0 V* 5) Note: *4 −20 V to −60 V DC power input. *5 +20 V to +60 V DC power input. Frame ground
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (1/14) Terminal
TRAFFIC IN/OUT (CH 1 to CH 8) (D-sub Connector, 37 Pins)
Description
2.048 Mbps HDB3 coded data input/output from/to D TE (CH 1 to CH 8), (Selectable 120-ohm, balanced/75-ohm, unbalanced)
Pins 1 (+) and 2 (−)
CH8 data input
Pins 3 (+) and 4 (−)
CH7 data input
Pins 6 (+) and 7 (−)
CH6 data input
Pins 8 (+) and 9 (−)
CH5 data input
Pins 11 (+) and 12 (−)
CH4 data input
Pins 13 (+) and 14 (−)
CH3 data input
Pins 16 (+) and 17 (−)
CH2 data input
Pins 18 (+) and 19 (−)
CH1 data input
Pins 20 (+) and 21 (−)
CH8 data output
Pins 22 (+) and 23 (−)
CH7 data output
Pins 25 (+) and 26 (−)
CH6 data output
Pins 27 (+) and 28 (−)
CH5 data output
Pins 29 (+) and 30 (−)
CH4 data output
Pins 31 (+) and 32 (−)
CH3 data output
Pins 34 (+) and 35 (−)
CH2 data output
Pins 36 (+) and 37 (−)
CH1 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN/OUT (CH 9 to CH 16) (D-sub Connector, 37 Pins)
2.048 Mbps HDB3 coded data input/output from/to D TE (CH 9 to CH 16), (Selectable 120-ohm, balanced/75-ohm, unbalanced), (for 16 x 2 MB system only)
Pins 1 (+) and 2 (−)
CH16 data input
Pins 3 (+) and 4 (−)
CH15 data input
Pins 6 (+) and 7 (−)
CH14 data input
Pins 8 (+) and 9 (−)
CH13 data input
Pins 11 (+) and 12 (−)
CH12 data input
Pins 13 (+) and 14 (−)
CH11 data input
3-15
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (2/14) Terminal
Pins 16 (+) and 17 (−)
CH10 data input
Pins 18 (+) and 19 (−)
CH9 data input
Pins 20 (+) and 21 (−)
CH16 data output
Pins 22 (+) and 23 (−)
CH15 data output
Pins 25 (+) and 26 (−)
CH14 data output
Pins 27 (+) and 28 (−)
CH13 data output
Pins 29 (+) and 30 (−)
CH12 data output
Pins 31 (+) and 32 (−)
CH11 data output
Pins 34 (+) and 35 (−)
CH 10 data output
Pins 36 (+) and 37 (−)
CH 9 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN/OUT with BNC (CH 1 to CH 8) (D-sub Connector, 37 Pins)
3-16
Description
2.048 Mbps HDB-3 coded data input/output from/to DTE (CH 1 to CH 8), (for 2/4/8 x 2 MB system only), (Fixed 120ohm, balanced)
Pins 1 (+) and 2 (−)
CH8 data input
Pins 3 (+) and 4 (−)
CH7 data input
Pins 6 (+) and 7 (−)
CH6 data input
Pins 8 (+) and 9 (−)
CH5 data input
Pins 11 (+) and 12 (−)
CH4 data input
Pins 13 (+) and 14 (−)
CH3 data input
Pins 16 (+) and 17 (−)
CH2 data input
Pins 18 (+) and 19 (−)
CH1 data input
Pins 20 (+) and 21 (−)
CH8 data output
Pins 22 (+) and 23 (−)
CH7 data output
Pins 25 (+) and 26 (−)
CH6 data output
Pins 27 (+) and 28 (−)
CH5 data output
Pins 29 (+) and 30 (−)
CH4 data output
Pins 31 (+) and 32 (−)
CH3 data output
Pins 34 (+) and 35 (−)
CH2 data output
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (3/14) Terminal
Description
Pins 36 (+) and 37 (−)
CH1 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN 75 Ω (CH 1 to CH 8) (BNC, Female)
2.048 Mbps HDB3 coded data signal input from DTE (CH 1 to CH 8), (for 2/4/8 x 2 MB system only), (Fixed 75ohm, unbalanced)
CH1
BNC
CH1 data input
CH2
BNC
CH2 data input
CH3
BNC
CH3 data input
CH4
BNC
CH4 data input
CH5
BNC
CH5 data input
CH6
BNC
CH6 data input
CH7
BNC
CH7 data input
CH8
BNC
CH8 data input
TRAFFIC OUT 75 Ω (CH 1 to CH 8) (BNC, Female)
2.048 Mbps HDB3 coded data signal output to DTE (CH 1 to CH 8),(for 2/4/8 x 2 MB system only), (Fixed 75ohm, unbalanced)
CH1
BNC
CH1 data output
CH2
BNC
CH2 data output
CH3
BNC
CH3 data output
CH4
BNC
CH4 data output
CH5
BNC
CH5 data output
CH6
BNC
CH6 data output
CH7
BNC
CH7 data output
CH8
BNC
CH8 data output
3-17
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (4/14) Terminal
TRAFFIC IN/OUT with BNC (CH 1 to CH 4) (D-sub Connector, 37 Pins)
Description
2.048 Mbps HDB-3 coded data input/output from/to DTE (CH 1 to CH 4), (for 4 x 2 MB system only), (Fixed 120-ohm, balanced)
Pins 11 (+) and 12 (−)
CH4 data input
Pins 13 (+) and 14 (−)
CH3 data input
Pins 16 (+) and 17 (−)
CH2 data input
Pins 18 (+) and 19 (−)
CH1 data input
Pins 29 (+) and 30 (−)
CH4 data output
Pins 31 (+) and 32 (−)
CH3 data output
Pins 34 (+) and 35 (−)
CH2 data output
Pins 36 (+) and 37 (−)
CH1 data output
Pins 5,10,15,24 and 33
Ground
TRAFFIC IN 75 Ω (CH 1 to CH 4) (BNC, Female)
2.048 Mbps HDB3 coded data signal input from DTE (CH 1 to CH 4), (for 4 x 2 MB system only), (Fixed 75-ohm, unbalanced)
CH1
BNC
CH1 data input
CH2
BNC
CH2 data input
CH3
BNC
CH3 data input
CH4
BNC
CH4 data input
TRAFFIC OUT 75 Ω (CH 1 to CH 4) (BNC, Female)
2.048 Mbps HDB3 coded data signal output to DTE (CH 1 to CH 4), (for 4 x 2 MB system only), (Fixed 75-ohm, unbalanced),
CH1
BNC
CH1 data output
CH2
BNC
CH2 data output
CH3
BNC
CH3 data output
CH4
BNC
CH4 data output
10/100BASE-T IN/OUT (Modular Connector RJ-45 8pins) (PORT1/PORT2)
3-18
LAN signal input/output (optional) (MDI-X/MDI auto-sensing) MDI-X MDI
Pin 1
RD +
TD +
Pin 2
RD −
TD −
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (5/14) Terminal
Description
Pin 3
TD +
RD +
Pin 6
TD −
RD −
IF IN/OUT (N-P Connector)
TX IF signal output to ODU and RX IF signal input from ODU Caution: Do not connect other cables to this jack, because the −43 V DC power is superimposed on this jack. Danger: Do not touch the jack core before turning off power switch.
3-19
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (6/14) Terminal
Description
OW/DSC/ASC (D-sub Connector, 25 Pins)
Engineering orderwire (EOW), digital service channel (DS C), analog service channel (ASC) and ALARM signal input/output
Pins 1 (+) and 2 (−)/
ASC1 input (VF) (optional), DSC 3 input (optional) or
Pins 1 and 2* 2
Alarm1*2 input (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 1 input (photocoupler) Normal signal in : Open Alarm signal in : Closed
Pins 3 (+) and 4 (−)/ Pins 3 and 4*
2
ASC2 input (VF) (optional), DSC 4 input (optional) or Alarm2*2 input (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 2 input (photocoupler) Normal signal in : Open Alarm signal in : Closed
Pins 5 (+) and 6 (−)
EOW input (VF)
Pins 7 (+) and 8 (−)
64 kHz clock input*1
Pins 9 (+) and 10 (−)
DSC1 input (RS-232C, 64K (G.703)* 1 or 64K (V.11)* 1)
Pins 11 (+) and 12 (−)
DSC2 input (RS-232C, RS-422 or RS-485)
Pins 14 (+) and 15 (−)/
ASC1 output (VF) (optional), DSC 3 output (optional) or
Pins 14 and 15*
2
Alarm1*2 output (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 1 output (relay contact) Normal signal out : Open Alarm signal out : Closed
Pins 16 (+) and 17 (−)/
ASC2 output (VF) (optional), DSC 4 output (optional) or
Pins 16 and 17* 2
Alarm2*2 output (optional) Notes: 1. *2 Applies to the ALM INTFC module. 2. Cluster Alarm 2 output (relay contact) Normal signal out : Open Alarm signal out : Closed
3-20
Pins 18 (+) and 19 (−)
EOW output (VF)
Pins 20 (+) and 21 (−)
64 kHz clock output* 1
Pins 22 (+) and 23 (−)
DSC1 output (RS-232C, 64K (G.703)* 1 or 64K (V.11)* 1)
Pins 24 (+) and 25 (−)
DSC2 output (RS-232C, RS-422 or RS-485)
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (7/14) Terminal
Pin 13
Description
Ground Notes:1. *1 Optional 2. Both ASC and DSC 64K cannot be used simultaneously.
ALM (D-sub Connector, 37 Pins)
Alarm and answer signal input/output
Pins 1 (COM), 2 (NO) and 3 (NC)
No. 1 transmitter alarm output*3 Between Pins 1 and 2 Normal state : Open Alarm state : Closed
Between Pins 1 and 3 Closed Open
Pins 4 (COM), 5 (NO) and 6 (NC)
No. 2 transmitter alarm output*3 Between Pins 4 and 5 Normal state : Open Alarm state : Closed
Between Pins 4 and 6 Closed Open
Pins 7 (COM), 8 (NO) and 9 (NC)
No. 1 receiver alarm output*3 Between Pins 7 and 8 Normal state : Open Alarm state : Closed
Between Pins 7 and 9 Closed Open
Pins 10 (COM), 11 (NO) and 12 (NC)
No. 2 receiver alarm output*3 Between Pins 10 and 11 Normal state : Open Alarm state : Closed
Between Pins 10 and 12 Closed Open
Pins 14
Buzzer signal output Note: The terminal is used as an input terminal of buzzer signal for the back-to-back station.
Pins 15
Buzzer signal input Note: The terminal is used as an input terminal of buzzer signal for the back-to-back station.
Pins 20 (COM), 21 (NO) and 22 (NC)
BER alarm output when BER worse than 10-6/10-5/10-4/10-3 (selectable)*3
Normal state Alarm state
: :
Between Pins 20 and 21 Open Closed
Between Pins 20 and 22 Closed Open
3-21
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (8/14) Terminal
Description
Pins 23 (COM), 24 (NO) and 25 (NC)
Maintenance alarm output* 3 Between Pins 23 and 24 Normal state : Open Alarm state : Closed
Pins 26 (COM), 27 (No. 2) and 28 (No. 1)
Switching answer signal output for transmitter Between Between Pins 26 and 27 Pins 26 and 28 No. 1 CH selection : Open Closed No. 2 CH selection : Closed Open
Pins 29 (COM), 30 (No. 2) and 31 (No. 1)
Switching answer signal output for receiver Between Between Pins 29 and 30 Pins 29 and 31 No. 1 CH selection : Open Closed No. 2 CH selection : Closed Open
Between Pins 23 and 25 Closed Open
Note:*3 The BER threshold values and alarm items are set in factory (default). To change the setting of alarm items by the PC, refer to Section 3.4.1 "Alarm Table" of this Manual. AUX ALM (D-sub Connector, 25 Pins)
3-22
Transmission network surveillance auxiliary Note: When an optional PM CARD module is mounted, following input/output terminals (Pins 1 to 21) are used as housekeeping alarm/control interface.
Pin 1
Input 11
Pin 2 (G)
Input 12
Pin 3
Input 21
Pin 4 (G)
Input 22
Pin 5
Input 31
Pin 6 (G)
Input 32
Pin 7
Input 41
Pin 8 (G)
Input 42
Pin 9
Input 51
Pin 10 (G)
Input 52
Pin 11
Input 61
Pin 12 (G)
Input 62
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (9/14) Terminal
Description
Pin 13
Ground
Pin 14
Output 11
Pin 15
Output 12
Pin 16
Output 21
Pin 17
Output 22
Pin 18
Output 31
Pin 19
Output 32
Pin 20
Output 41
Pin 21
Output 42 Note: Input[ ] indicates the input of housekeeping alarm. The figure means that same order of tens makes the same pair e.g. 11/12 forms a pair. IDU side interface uses that of photo-coupler, the photo-coupler turns ON if pair elements contact with each other. Output[ ] indicates the output of housekeeping alarm. Figure means the same as in the Input. IDU side output uses the relay interface.
Pins 22 and 23
Remote switching control signal input for release
Pins 22 and 24
Remote switching control signal input for No. 1 channel No. 1 channel selection : closed
Pins 22 and 25
Remote switching control signal input for No. 2 channel No. 2 channel selection : closed
3-23
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (10/14) Terminal
NMS/RA (D-sub Connector, 15 Pins)
Network management system (NMS) data input/output or remote access (RA) data input/output Note: When the PM CARD is not mounted on the equipment, this connector is used for Remote Access. PM CARD
RA
Pin 1
Party alarm management system (PAMS) TXD
RA TXD
Pin 2
EMS TXD/TXD+
RA GND
Pin 3
EMS RXD/TXD−
RA RXD
Pin 4
EMS TXDR
RA RTS
Pin 5
EMS TRS/RXD+
RA CTS
Pin 6
EMS CTS/RXD−
Pin 7
Ground
Pin 9
PAMS RXD
Pin 10
NMS TXD/TXD+
Pin 11
NMS RXD/TXD−
Pin 12
NMS TXDR
Pin 13
NMS RTS/RXD+
Pin 14
NMS CTS/RXD−
LA PORT (No. 1) (D-sub Connector, 15 pin)
3-24
Description
Control/monitoring signal input/output from/to the personal computer for No. 1 channel
Pin 1
TXD
Pin 3
RXD
Pin 4
RTS
Pin 5
CTS
Pin 11
LOCAL CTS
Pin 12
LOCAL RTS
Pin 13
LOCAL RXD
Pin 15
LOCAL TXD
Pins 2, 8 and 14
Ground
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (11/14) Terminal
LA PORT (No. 2) (D-sub Connector, 15 pin)
Description
Control/monitoring signal input/output from/to the personal computer for No. 2 channel
Pin 1
TXD
Pin 3
RXD
Pin 4
RTS
Pin 5
CTS
Pin 11
LOCAL CTS
Pin 12
LOCAL RTS
Pin 13
LOCAL RXD
Pin 15
LOCAL TXD
Pins 2, 8 and 14
Ground
LA PORT (COMMON) (D-sub Connector, 15 pin)
Control/monitoring signal input/output from/to personal computer for both No. 1 and No. 2 channels
Pin 1
TXD
Pin 3
RXD
Pin 4
RTS
Pin 5
CTS
Pin 11
LOCAL CTS
Pin 12
LOCAL RTS
Pin 13
LOCAL RXD
Pin 15
LOCAL TXD
Pins 2, 8 and 14
Ground
NMS LAN (RJ45 8 pins)
Pasolink network management station (PNMS) data input/ output
Pin 1
LAN PNMS TX+
Pin 2
LAN PNMS TX−
Pin 3
LAN PNMS RX+
Pin 6
LAN PNMS RX−
3-25
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (12/14) Terminal
WS /SC LAN (RJ45 8 pins)
Description
Way side signal input/output For 120 ohms balanced interface
Pin 1
WS OUT (+)
Pin 2
WS OUT (−)
Pin 3
Reserved for SC LAN INTFC
Pin 4
WS IN (+)
Pin 5
WS IN (−)
Pin 6
Reserved for SC LAN INTFC
Pin 7
open
Pin 8
Frame ground (G) For 75 ohms unbalanced interface
3-26
Pin 1
WS OUT
Pin 2
Reserved for WS INTFC (120 ohms balance)
Pin 3
Reserved for SC LAN INTFC
Pin 4
WS IN
Pin 5
Reserved for WS INTFC (120 ohms balance)
Pin 6
Reserved for SC LAN INTFC
Pin 7
open
Pin 8
WS IN/OUT (G)
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (13/14) Terminal
Description
Do not connect any cable to the "Reserved" pins. Note: Available if WS INTFC is equipped. Disable when SC LAN INTFC is equipped. When WS signal is connected between two IDUs, perform wiring as follows.
IDU B WS/SC LAN (RJ45)
IDU A WS/SC LAN (RJ45) WS (120 ohms) 1 2 3 4 5 6 7 8
IDU B WS/SC LAN (RJ45)
IDU A WS/SC LAN (RJ45) WS (75 ohms) 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3-27
OPERATION
ROI-S04488
Table 3-2 Interface Terminals and Jacks of 1+1 System (14/14) Terminal
Description
WS /SC LAN (RJ45 8 pins)
DSC data for LAN
Pin 1
LAN DSC TX+
Pin 2
LAN DSC TX−
Pin 3
LAN DSC RX+
Pin 4
Reserved for WS INTFC
Pin 5
Reserved for WS INTFC
Pin 6
LAN DSC RX−
Pin 7
open
Pin 8
open Note: Available when SC LAN INTFC is equipped. Disabled when ALM INTFC, ASC INTFC, DSC INTFC 64K or WS INTFC (in case of 16x2MB) is used. Do not connect any cable to the "Reserved" pins. When SC LAN signal is connected between two IDUs, perform wiring as follows. IDU B WS/SC LAN (RJ45)
IDU A WS/SC LAN (RJ45) 1 2 3 4 5 6 7 8
SELV (LINE IN) (Molex M5557-4R Connector, 4 Pins)
SC LAN INTFC
-20 V to -60 V DC or +20 V to +60 V DC power input Note: The range of DC power input depends on system requirement.
Pin 1
0 V*4 (or +48 V* 5)
Pin 2
−48 V*4 (or 0 V*5) Note: *4
−20 V to −60 V DC power input.
5
+20 V to +60 V DC power input.
* FG
3-28
1 2 3 4 5 6 7 8
Frame ground
OPERATION
ROI-S04488
3.2 Controls, Indicators and Test Jacks The controls and indicators and test jacks on the IDU (see Fig. 3-3) are described as follows. IDU indicator Lights when: • Input data stream of CH ( ) from DTE is lost, • AIS (all “1”) signal of CH ( ) is received from DTE (selectable), • TX/RX clock synchronization is lost at the DPU section, • If a 2 MB is fed to a CH which is selected as "Not Used" (selectable), • If a 2 MB is fed to the WS CH after setting to "Not Used" (selectable), • AIS signal of CH ( ) is sent (depending on system requirement) (selectable), • Bipolar output pulse of CH ( ) is lost at the INTFC section, • Carrier synchronization is lost at the DEM section, • High bit error rate (High BER) is worse than preset value (1 x10-3) at the DPU section, • BER is worse than preset value at the DPU section (1x10-3, 1x10-4, 1x10-5 or 1x10-6, selectable), • Frame synchronization is lost at the DPU section, • ATPC MAX PWR alarm condition, • VCO synchronization is lost at the MOD section, • Output data stream or master clock signal is lost at the DPU(TX) section, ODU indicator Lights when: • Transmit RF power decreases 3 dB from normal at the ODU, • Receiver input level decreases by a preset value from squelch level at the ODU, • APC loop of local oscillator unlocks at the ODU or, • IF signal from the IDU is lost at the ODU,
3-29
OPERATION
ROI-S04488
MAINT indicator Lights when the following conditions are controlled by the PC: • Maintenance condition, • Loopback condition, • BER AIS condition, • MOD CW condition, • MUTE (TX output power) condition, PWR switch: Turns input DC power on or off. PWR indicator: Lights when equipment is in normal operation. RESET switch: RESET switch initiates the CPU operation. CALL switch: Transmits calling signal on engineering orderwire (EOW). buzzer in opposite station rings.
Then,
EOW jack: Gives access to EOW signal immediately when headset is connected. 100M indicator: Lights when 100 Mbps is selected in data speed of LAN interface. Goes out when 10 Mbps is selected in data speed of LAN interface. LINK/ACT indicator (Green): Lights when the IDU and associated equipment are linked. It blinks during data transmission. (LAN INTFC, SC LAN INTFC) COLX/DUPLEX indicator (Amber): Lights when : • The input/output LAN signal is in Full Duplex mode (LAN INTFC), • When the LAN signal in Half Duplex mode, a collision condition occurs.(LAN INTFC, SC LAN INTFC)
3-30
OPERATION
ROI-S04488
TX ALM 1 indicator (Only for 1+1 system): Lights when: • Transmitter RF output power decreases 3 dB from normal at the No. 1 channel ODU, • APC loop of the local oscillator unlocks or IF signal from the IDU is lost at the No. 1 channel ODU, • Output data stream or master clock signal is lost at the No. 1 channel DPU (TX), • VCO synchronization is lost at the No. 1 channel MOD, • If a 2 MB is fed to a CH which is selected as "Not Used" (selectable) at the No. 1 channel IDU, • If a 2 MB is fed to the WS CH after setting to "Not Used" (selectable) at the No. 1 channel IDU, • Communication between CPU of No. 1 channel ODU and CPU on the IDU is lost. TX ALM 2 indicator (Only for 1+1 system) Lights when: • Transmitter RF output power decreases 3 dB from normal at the No. 2 channel ODU, • APC loop of the local oscillator unlocks or IF signal from the IDU is lost at the No. 2 channel ODU, • Output data stream or master clock signal is lost at the No. 2 channel DPU (TX), • VCO synchronization is lost at the No. 2 channel MOD, • If a 2 MB is fed to a CH which is selected as "Not Used" (selectable) at the No. 2 channel IDU, • If a 2 MB is fed to the WS CH after setting to "Not Used" (selectable) at the No. 2 channel IDU, • Communication between CPU of No. 2 channel ODU and CPU on the IDU is lost.
3-31
OPERATION
ROI-S04488
RX ALM 1 indicator (Only for 1+1 system) Lights when: • Receiver input level decreases lower than a preset value from squelch level at the No. 1 channel ODU, • APC loop of the local oscillator unlocks at the No. 1 channel ODU, • IF signal is lost at the No. 1 channel DEM, • High BER is worse than preset value (1 × 10−3) at the DPU, • BER is worse than preset value at the No. 1 channel DPU (1 × 10−3, 1 × 10−4, 1 × 10−5 or 1 × 10−6 selectable), • Frame synchronization is lost at the No. 1 channel DPU, • Communication between CPU of No. 1 channel ODU and CPU of the IDU is lost. RX ALM 2 indicator (Only for 1+1 system) Lights when: • Receiver input level decreases lower than a preset value from squelch level at the No. 2 channel ODU, • APC loop of the local oscillator unlocks at the No. 2 channel ODU, • IF signal is lost at the No. 2 channel DEM, • High BER is worse than preset value (1 × 10−3) at the No. 2 channel DPU, • BER is worse than preset value at the No. 2 channel DPU (1 × 10−3, 1 × 10−4, 1 × 10−5 or 1 × 10−6 selectable), • Frame synchronization is lost at the No. 2 channel DPU, • Communication between CPU of No. 2 channel ODU and CPU of the IDU is lost. TX OPR 1 indicator (Only for 1+1 system): Lights when the modulator and transmitter of No. 1 channel are selected.
3-32
OPERATION
ROI-S04488
TX OPR 2 indicator (Only for 1+1 system): Lights when the modulator and transmitter of No. 2 channel are selected. RX OPR 1 indicator (Only for 1+1 system): Lights when the demodulator and receiver of No. 1 channel are selected. RX OPR 2 indicator (Only for 1+1 system): Lights when the demodulator and receiver of No. 2 channel are selected. OPR SEL No. 1-AUTO-No. 2 switch (Only for 1+1 system) Enables channel switching depending on the setting position in Maintenance conditions as follows: No. 1 : Manually select No. 1 channel AUTO : Automatic switchover control No. 2 : Manually select No. 2 channel Caution: Before the start of maintenance, including operation of the OPR SEL SW on the front panel of the equipment, select the equipment to maintenance mode using the LCT. After all operation for maintenance have been completed, perform MAINT OFF setting. EOW
CALL
PASOLINK ODU IDU
RESET PWR
IDU for 1+0
MAINT
NMS LAN
FUSE (7.5A) +
− NMS/RA
SELV
LA PORT
PASOLINK
FUSE (7.5A)
RESET PWR ODU IDU MAINT +
−
No. 1 CH MD UNIT
SELV
LA PORT EOW CALL
PASOLINK RESET OPR SEL No.1
MS LAN
OPR TX
ALM
RX
TX
SW UNIT
RX 1
− DSC/ASC
NMS/RA
LA PORT
2
IDU for 1+1
No.2
PASOLINK
FUSE (7.5A)
+
− LA PORT
No. 2 CH MD UNIT
RESET PWR ODU IDU MAINT
SELV
Fig. 3-3 Controls, Indicators and Test Jacks of the IDU
3-33
OPERATION
ROI-S04488
3.2.1 75 ohms/120 ohms Impedance Switch For the IDU listed in the following table, 75 ohms/unbalanced - 120 ohms /balanced impedance switching of 2 MB interface is applicable on the front board as shown in Fig. 3-4. Note: These switches are already set by factory setting according to customer requirement.
IDU System 1+0
3-34
1+1
H0091A/J/L/M
H0161A/J/L/M
4 x 2MB
H0091N
H0161N
2/4/8 x 2MB
H0091F/H/K/P
H0161F/H/K/P
2/4/8/16 x 2MB
OPERATION
ROI-S04488
(IDU) !
-43V OUTPUT
Power down IDU before disconnection or connection of Cable
FRONT
TOP VIEW
S3
S4
S1
S2
FRONT BOARD 2
S3
FRONT BOARD 1
IDU in 1+0 System
(SW UNIT)
FRONT TOP VIEW
S3
S4
S1
S2
FRONT BOARD 2
S3
FRONT BOARD 1
SW Unit in 1+1 System Fig. 3-4 75 ohm-120 ohm Impedance Setting (1/2)
3-35
OPERATION
ROI-S04488
Switching Function
Set Position
Remark
When the 75-ohm impedance is used, all switches are set to as follows: 75
CH9
CH12
CH13
75
CH16
75
S3
S4
75 S1
120
120
120 CH1
CH4
75
CH5
CH8
120
120
75 S2
120
Only S1 applies to H0091A, J, L, M/H0161A, J, L, M IDU (for 4×2 MB). S1 and S2 apply to H0091N/H0161N IDU (for 2/4/8×2MB). S1, S2, S3 and S4 apply to H0091F, H, K, P/H0161F, H, K, P IDU (for 2/4/8/16×2 MB).
When the 120-ohm impedance is used, all switches are set to as follows: 75
CH9
CH12
75
CH13
CH16
S3
Selection for 75/120 ohm impedance
Selected Position 75 S4
120
120 75
CH1
CH4
75
120 CH5
CH8
S1
120
120
120
When the 75-ohm impedance is used, two switches are set to as follows: S3
75 S2
WS signal interface impedance selection.
75
120
When the 120-ohm impedance is used, two switches are set to as follows: S3
75
120
Fig. 3-4 75 ohm-120 ohm Impedance Setting (2/2)
3-36
Selected Position
OPERATION
ROI-S04488
3.3 Equipment Start-up and Shut-down Procedure for equipment start-up and shut-down are described below. Warning: To prevent accidental IDU power switch lever movement, the power switch lever is locked. When set the power switch to on/off, it must be pulled out power switch lever knob to unlock the switch lever.
3.3.1 Start-up Caution: It is recommended that you connect the IDU to ODU after the TX/RX frequency and TX power control setting has been set on the IDU. This process is most important for the following ODUs that may be emitted TX power if you set the channel number to "0ch" which is not defined (excepting 13/26/38 GHz band) by the Radio Frequency Assignment. Code No. of Corresponding ODU: H0738 (7 GHz), H0739 (8 GHz), H0330 (13 GHz), H0331 (15GHz), H0332 (18GHz), H0333 (23 GHz), H0334 (26 GHz), H0335 (38 GHz) Test Equipment and Accessories Required
• Agilent 34401A Digital Multimeter (or equivalent) with Test Leads Step
1
Procedure
Check that the LINE IN voltage is between +20 V to +60 V/ −20 V to −60 V with the digital multimeter, before connecting the power connector to the IDU, Note: The range of DC power input depends on system requirement.
2
Turn on the POWER switch on the IDU (refer to Fig. 3-5), Note: In 1+ 1 system, When neither No.1 nor No.2 channel is working, first set the OPE SEL switch to the desired (No.1 or No.2) position and power on the selected MD Unit or set the OPE SEL switch to neutral (Auto) position and power on both MD units. When either No.1 or No.2 channel is working, perform MAINTE ON condition with the LCT, set the OPR SEL No.1-No.2 switch on the IDU to the working channel side, then, turn on the power switch of the not working channel.
3-37
OPERATION
ROI-S04488
3
Allow equipment to warm up for at least 30 minutes. EOW
PASOLINK ODU IDU
RESET PWR
FUSE (7.5A) +
− NMS/RA
SELV
LA PORT
No.1 Power Switch LINE IN Connector
PASOLINK
FUSE (7.5A)
RESET PWR ODU IDU MAINT +
−
OPR SEL No.1 - No.2 Switch
SELV
LA PORT EOW CALL
IDU for 1+1 System
Power Switch LINE IN Connector
MAINT
NMS LAN
IDU for 1+0 System
CALL
PASOLINK RESET OPR SEL No.1
MS LAN
OP R TX
A LM
RX
TX
RX 1
− DSC/ASC
NMS/RA
LA PORT
2 No.2
PASOLINK
FUSE (7.5A)
No.2 Power Switch LINE IN Connector
RESET PWR ODU IDU MAINT +
− SELV
LA PORT
Fig. 3-5 Front View of the IDU for Powering Up
3.3.2 Shut-down Step
Procedure
For 1+0 system 1
Turn off the POWER switch on the front of the IDU. For 1+1 system
1
Perform the setting for MAINT ON condition with the LCT,
2
Set the OPR SEL No.1 - No.2 switch to the channel position to be on-line,
3
Turn off the power switch on the channel of off-line. Note: In 1+1 system, before turn off the POWER switch of No.1 or No. 2 channel, perform MAINT ON condition with the LCT.
3-38
OPERATION
ROI-S04488
3.4 Equipment Setting and Monitoring Test Equipment and Accessories Required
• Personal Computer • RS-232C cable • Screw Driver The control of the IDU and ODU digital radio system can be carried out via the LA PORT or NMS/RA of the IDU. Connect a Personal Computer to the IDU with an RS-232C cable. The specifications of the required communication port condition of the personal computer are listed below. • Baud rate :
9600
• Data Length :
8
• Parity Check :
None
• Stop bit :
2
• Flow control:
None
• Emulation :
VT100 Video Terminal
• Transmission: HyperTerminal*: Send line ends with line feeds : Yes Local echo : No • Receiving:
CR : No Return on the right edge : Yes Force incoming data to 7-bit ASCII : No
Notes: 1. HyperTerminal : Microsoft * For Windows 95/98/Me/NT4.0/2000/XP 2. When Windows NT4.0 and HyperTerminal is used, “Program Download” function is not available. In this case, please use other terminal software. (e.g. TeraTerm Pro 2.3: http://hp.vector.co.jp/authors/VA002416/teraterm.html)
3-39
OPERATION
ROI-S04488
The pin assignment is shown in Fig. 3-6. The cable length of RS-232C between the personal computer and IDU equipment shall be less than 15 m. IDU SIDE LA PORT/NMS/RA CONNECTOR PIN SIGNAL No. NAME
PERSONAL COMPUTER SIDE SIGNAL NAME
PIN No.
GND
5
DTR
4
DSR
6
RTS
2
GND
7
5
CTS
CTS
8
4
RTS
TXD
3
3
RXD
RXD
2
1
TXD
D-SUB CONNECTOR (9 PIN)
(BLACK)
D-SUB CONNECTOR (15 PIN)
Interface Terminal (9 pin - 15 pin) Fig. 3-6 RS-232C Cable Pin Assignment
3.4.1 Setting Procedure from LCT The setting of each item for the IDU is performed by the PC as follows: Caution:
When login is not possible, check if settings of the communication format are proper.
Caution:
Do not turn on the power of the IDU leaving cable connection between the PC and RA PORT of the IDU.
Step
1
3-40
Procedure
Connect the personal computer (PC) to the LA PORT or NMS/ RA terminal of the IDU using an RS-232C cable as shown in Fig. 3-7,
OPERATION
ROI-S04488
EOW
RS-232C CABLE(BLACK)
CALL
PASOLINK ODU IDU
RESET PWR
MAINT
FUSE (7.5A) +
−
NMS/RA
SELV
LA PORT
IDU
PASOLINK
FUSE (7.5A)
RESET PWR ODU IDU MAINT +
− SELV
LA PORT
PERSONAL COMPUTER
EOW CALL
PASOLINK RESET OPR SEL No.1
OPR TX
ALM
RX
TX
RX 1
− NMS/RA
LA PORT
2 No.2
PASOLINK
FUSE (7.5A)
RESET PWR ODU IDU MAINT +
− SELV
LA PORT
IDU
Note: When the controlling or setting of own station are performed, connect the cable to the LA PORT. When the controlling or setting of opposite station are performed, connect the cable to the NMS/RA port. But, if the following cases are applied, the NMS/ RA terminal can not be used. • When the PM CARDs are mounted on Local and Remote equipment. • When BER is degraded. Fig. 3-7 Equipment and Monitoring Setup
Step
Procedure
Note: The keys, “0” to “9” are used for selection of the menu or entering values. “Enter” key is used for confirmation of entering values. “Esc” key is used for cancellation of entering values and display the higher rank menu. 2
Turn on the power on the PC. Then, start the communication software (e.g. HyperTerminal), Note: At the end of LCT operation log out from LCT menu by keying "99" and then exit from the communication software. In case if you have exit from the communication software without logging out from LCT, repeat connecting and disconnecting of the RS 232C cable once to reset.
3
Press the “CTRL” and “D” keys at the same time,
3-41
OPERATION
ROI-S04488
Step
Procedure
4
Enter the specified password from the keyboard and press the “Enter” key,
Passwor d
:
Note: When the PC is connected to the NMS/RA terminal to control the opposite station, enter password of the opposite station. 5
Press the “0” key and “Enter” key. Then, perform step 8. If the password should be changed, press the “1” key and “Enter” key,
Passwor d : ********* Change Passwor d? ( no: 0 / yes: 1) :
6
Enter the new password from the keyboard and press the “Enter” key,
Passwor d : ********* Change Passwor d? ( no: 0 / yes: 1) : 1 New Passwor d :
Note: For password, “0” to “9”, “A” to “Z” and “a” to “z” are available (31 letters maximum). 7
To confirm the password, re-enter the password from the keyboard and press the “Enter” key,
Passwor d : ********* Change Passwor d? ( no: 0/ yes: 1) : 1 New Passwor d : ********** New Passwor d ( Re- ent er ) : **********
8 1. 2. 3. 99.
Following menu item is displayed, Set t i ng Mai nt enanc e Moni t or i ng Exi t
Sel ect f unct i on No. :
3-42
OPERATION
ROI-S04488
Step
9
Procedure
Press the “1” key and “Enter” key, then, following setting menu is displayed,
Set t i ng 1. Bi t r at e ( 4×2MB) 2. AI S RCVD al ar m/ st at us ( st at us) 3. AI S SEND al ar m/ st at us ( st at us) 4. TX/ RX f r equency ( 5ch) 5. TX power c t r l ( 0dB) 6. Mai n channel usage 1- 16 ( used: UNNN NNNN #### ####) 7. BER al ar mt hr es hol d ( 10- 4) 8. Fr ame I D ( 0) 9. WS channel usage ( not used) 10. DSC 1 ( 232) 11. DSC 2 ( 232) 12. DEM i nver t ( of f ) 13. Al ar m t abl e 14. Next i t ems 00. Menu 99. Exi t Sel ec t i t em No. :
Notes: 1. In item No. 1, the required bit rate is indicated in the parenthesis ( ) on “Bit rate”. Bit rate 2 x 2MB / 4 x 2MB / 8 x 2MB / 16 x 2MB Changing the bit rate will cause temporary communication loss until the bit rate of the opposite site is changed. The buzzer may be issued until then. 16x2MB bit rate is not supported on MDP-17MB-3/4A. 2. In item No. 2 and item No. 3, setting for alarm indication of AIS RCVD/AIS SEND as follows, alarm: to include ALARM LED indication item, status: to exclude ALARM LED indication item. 3. In item No. 4, both channel numbers are indicated as No.1: *ch / No.2: *ch if twin path configuration is selected. 4. In item No. 5 shows in case of MTPC system, TX power ctrl (ATPC) *1 or TX power ctrl (No. 1: ATPC / No. 2: ATPC) *2 is indicated. In case of ATPC system, Note: *1 1+0 or Hot standby system. *2 Twin path system. 5. In item No. 6, following significant symbol letters are used to display the status for each channel. “#” : signifies E1 channel which is inhibited by the hardware restriction or LAN signal transmission.
3-43
OPERATION
ROI-S04488
Step
Procedure
“N” : signifies not used channel. “U” : signifies E1 channel which is used. 6. In item No. 10 and item No. 11, 232 (i.e. RS232C) is standard. 10
2.
Press the “2” key and “Enter” key, then, following item is displayed, AI S RCVD al ar m/ st at us ( st at us)
AI S RCVD al ar m/ st at us ( st at us: 0 / al ar m: 1) :
Note: When AIS RCVD “alarm” is selected, AIS RCVD condition will lit the IDU alarm LED. When AIS RCVD “status” is selected, AIS RCVD condition will not lit the IDU alarm LED. 11
Press either “0” or “1” key and “Enter” key for setting, if not, press the “Esc” key,
12
Press the “3” key and “Enter” key, then, following item is displayed,
3.
AI S SEND al ar m/ s t a t us / ( s t at us )
AI S SEND al ar m/ st at us ( st at us: 0 / al ar m: 1) :
Note: When AIS SEND “alarm” is selected, AIS SEND condition will lit the IDU alarm LED. When AIS SEND “status” is selected, AIS SEND condition will not lit the IDU alarm LED. 13
Press either “0” or “1” key and “Enter” key for setting, if not, press the “Esc” key,
14
Press the “4” key and “Enter” key, then, following item is displayed,
For 1+0 / HS System 4.
TX/ RX f r equency ( 5ch)
TX/ RX f r equency ( 0ch – 255ch) :
15
3-44
Enter the channel No. and press the “Enter” key, if not, press the “Esc” key,
OPERATION
ROI-S04488
Step
Procedure
For 1+1 Twin Path System 4. TX/ RX f r equency ( No. 1: 5ch / No. 2: 10ch) 1. 2. 00. 99.
No. 1 TX/ RX f r equency ( 5ch) No. 2 TX/ RX f r equency ( 10ch) Menu Exi t
Sel ec t i t em No.
16
1.
:
Press the “1” key and “Enter” key, then, following setting is displayed,
No. 1 TX/ RX f r equency ( 5ch)
No. 1 TX/ RX f r equency ( 0ch – 255ch) :
17
Enter the channel No. and press the “Enter” key, if not, press the “Esc” key,
18
Press the “2” key and “Enter” key, then, enter the channel number for No.2 and press the “Enter” key,
2.
No. 2 TX/ RX f r equency ( 10ch)
No. 2 TX/ RX f r equency ( 0ch – 255ch) :
19
Press twice the “Esc” key to go back to setting menu in step 9,
20
Press the “5” key and “Enter” key, then, following item is displayed,
5. TX power ct r l ( 0dB) 1. 2. 3. 4. 5. 00. 99.
ATPC/ MTPC MTPC TX power ATPC power r ange ODU ALM mode RX t hr eshol d Menu Exi t
( MTPC) ( 0dB) ( MAX : 0dB / MI N : - 30dB) ( hol d) ( - 60dBm)
3-45
OPERATION
ROI-S04488
Step
21
1.
Procedure
Press the “1” key and “Enter” key, then, following item is displayed, ATPC/ MTPC ( MTPC)
ATPC/ MTPC ( MTPC: 0 / ATPC: 1) :
22
2.
Press the “0” key and “Enter” key, when the “0” key is pressed to select MTPC TX power setting, press the “2” key and “Enter” key, the following appears, MTPC TX power ( 0dB)
MTPC TX power ( - 30dB t o 0dB) : - 0
23
Enter the MTPC TX power level for setting and press the “Enter” key, if not, press the “Esc” key,
24
When the “1” key is pressed to select ATPC TX power setting in step 21, press “3” key and “Enter” key to select ATPC TX power range setting, the following appears,
3.
ATPC TX power r ange( MAX : 0dB / MI N : - 30dB)
MAX power ( - 30 t o 0dB) : - 0 MI N power ( - 30 t o 0dB) : - 30
Notes: 1. The MAX power must be set to a value larger than MIN power, 2. When the TX power control mode is changed from MTPC to ATPC, if the MAX power is set to -30dB in MTPC, both MAX and MIN power may be set to -30dB. 25
3-46
Enter the ATPC TX power maximum level and minimum level and press the “Enter” key for setting, if not, press the “Esc” key,
OPERATION
ROI-S04488
Step
26
4.
Procedure
Press the “4” key and “Enter” key, then, following item is displayed, ODU ALMmode( hol d)
ODU ALM mode ( MAX: 0 / MI N: 1 / hol d: 2) :
Note:
Selecting control mode of the TX power. When ATPC control communication is interrupted, the TX power is controlled as follows. MAX: TX power is controlled to maximum level. MIN: TX power is controlled to minimum level. hold: TX power is controlled to keep current level.
27
Press any key and “Enter” key, to setting,
28
Press the “5” key and “Enter” key, then, following item is displayed,
5.
RX t hr eshol d( - 72dBm)
RX t hr eshol d ( - 80 t o - 30dBm) :
29
Enter any level from -80 to -30 and press the “Enter” key for setting,
30
Press twice the “Esc” key to go back to setting menu in step 9,
31
Press the “6” key and “Enter” key, then, following item is displayed,
6. Mai n channel usage 1- 16 ( 1: used 2: not used 5: not used 6: not used 9: N/ A 10: N/ A 13: N/ A 14: N/ A
3: not used 4: not used 7: not used 8: not used 11: N/ A 12: N/ A 15: N/ A 16: N/ A
Sel ect channel No. :
Notes: Set the channel for use with concerning the following basis. 1. Restricted E1 channels by hardware, which are indicated by “# ”on the Setting display. 2. E1 channels which are not available to use when 10/ 100BASE-T(X) LAN is assigned. (see Table 3-3 Applicable Traffic Channel) 3. Reserved E1 channels.
3-47
OPERATION
ROI-S04488
Step
32
Procedure
Enter the channel No. and press the “Enter” key to change the setting, following channel setting is displayed,
6. Mai n channel usage 1- 16 ( 1: used 2: not used 5: not used 6: not used 9: N/ A 10: N/ A 13: N/ A 14: N/ A
3: not used 4: not used 7: not used 8: not used 11: N/ A 12: N/ A 15: N/ A 16: N/ A
Sel ect channel No. : Channel 1 ( used: 0 / not used: 1) :
33
Press either “0” or “1” key and “Enter” key for setting, if not, press the “Esc” key,
34
Press the “6” key and “Enter” key, repeat step 31 to step 33 for each channel setting,
35
Press twice the “Esc” key to go back to setting menu in step 9,
36
Press the “7” key and “Enter” key, then, following item is displayed,
7.
BER al ar mt hr es hol d ( 10- 4)
BER al ar m t hr eshol d ( 10- 3: 0 / 10- 4: 1 / 10- 5: 2 / 10- 6: 3) :
Notes: 10-3 signifies 1 x 10-3. Default value is a 10-4. 37
Press any “0” to “3” key and “Enter” key for setting, if not, press the “Esc” key,
38
Press the “8” key and “Enter” key, then, following item is displayed,
8.
Fr ame I D ( 0)
I nput I D No. ( 0- 7) :
3-48
OPERATION
ROI-S04488
Step
39
Procedure
Press the desired frame ID number and “Enter” key for setting, if not, press the “Esc” key, Note: The frame ID number must be set to the same number with the opposite station as follows (factory setting status): • 2 x 2MB/4 x 2 MB : 0 • 8 x 2MB : 1 • 16 x 2MB : 2
40
9.
Press the “9” key and “Enter” key, then, following item is displayed, WS channel usage ( not used)
WS channel usage ( used: 0 / not used: 1) :
Note: When the WS INTFC (optional) module is not mounted, this item can not be selected. The WS transmission is applicable only in the 16 x 2MB system. 41
Press either “0” or “1” key and the “Enter” key for setting, if not, press the “Esc” key,
42
Press the “1”, “0” keys and “Enter” key, then, following item is displayed,
10. DSC 1 ( 232) DSC 1 ( 232: 0 / 64k: 1) :
43
Press the either “0” or “1” key and “Enter” key for setting, if not, press the “Esc” key, Note: 232 — RS-232C provides standard 64k — 64 kbps is applicable when optional 64K INTFC is provided.
44
Press the “1”, “1” keys and the “Enter” key, then, following item is displayed,
11. DSC 2 ( 232) DSC 2 ( 232: 0 / 422: 1 / 485( TERM) : 2 / 485( NON TERM) : 3) :
3-49
OPERATION
ROI-S04488
Step
45
Procedure
Press any “0” to “3” key and “Enter” key for setting, if not, press the “Esc” key, Note: 232 — RS-232C, 422 — RS-422, 485 (TERM)— RS-485 (Terminating), 485 (NON TERM)— RS-485 (Non-Terminating). RS485 is an exclusive interface linked to “M10” which is the product of NEC. When two or more IDU are connected to one M10, only one set is set as “TERM.” Others are set as “NON TERM.”
46
Press the “1”, “2” keys and press the “Enter” key, then, following item is displayed,
12. DEM i nver t ( of f ) DEM i nver t ( of f : 0 / on: 1)
:
Select on/off from following table according to the frequency band and shift frequency. Note: Default value is off. Frequency Band (ODU Code No.)
Shift Frequency
7G (H0738)
154 161 168 245 119 126 266 311.32 266
8G (H0739)
13G (H0330) 15 G (H0331)
308 315 420 490 728
Frequency Band (ODU Code No.)
Shift Frequency
DEM Invert
on on on on on on on off off
18 G (H0332)
off off off off off
26 G (H0334)
340 1008 1010 1092.5 1560 600 1008 1050 1200 1232 855 1008 700 1000 1260
off off off off off off off off off off off off off off off
DEM Invert
23 G (H0333)
38 G (H0335)
47
Press the “0” or “1” key and “Enter” key for setting, if not, press the “Esc” key,
48
Press the “1”, “3” keys and press the “Enter” key, then, following item is displayed, Note: The following display is for initial values. When the resetting of item is required, perform steps 50 to 57 for corresponding item.
3-50
OPERATION
ROI-S04488
Step
Procedure
For 1+0 System 13. Al ar m t abl e 1/ 2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Pr ess
For mC1 I NPUT L OSS OUT AI S RCVD AI S SEND OUTPUT LOSS LAN I NTFC ALM OUT WS I NPUT LOSS WS AI S RCVD WS AI S SEND WS OUTPUT LOSS TX CLK LOSS OUT FSYNC ALM HI GH BER ALM LOWBER ALM BER ALM any key t o cont i nue…
49
For mC2
For mC3
For mC4
OUT OUT
OUT
OUT
OUT
OUT
OUT
Press any key, then, following Alarm table 2/2 appears,
13. Al ar m t abl e 2/ 2 For mC1 OUT
For mC2
15. MOD ALM 16. DEM ALM 17. OPR ALM OUT 18. TX PWR ALM OUT 19. RX LEV ALM 20. APC1 AL M OUT 21. APC2 AL M OUT 22. I F I NPUT ALM OUT 23. MAI NT MASK Sel ect i t em No. ( 1- 23, 0: no change) :
For mC3
For mC4
MASK
MASK
OUT
OUT OUT
OUT OUT OUT
Notes: 1. Alarm table displayed on the LCT depends on system configuration. 2. C1 to C4 will appear on the ALM/AUX ALM terminals. C1: 1, 2 and 3 pins C2: 4, 5 and 6 pins C3: 20, 21 and 22 pins C4: 23, 24 and 25 pins 3. The items which are applied alarm output are indicated with “OUT” and not applied alarm output are indicated with “–”. 4. Selecting item No. changes depending on the mounted modules. 5. The outputs which are inhibited under maintenance conditions are indicated with "MASK".
3-51
OPERATION
ROI-S04488
Step
Procedure
For 1+1 System 12. Al ar mt abl e 1/ 3 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
I NPUT LOSS AI S RCVD AI S SEND OUTPUT LOSS LAN I NTFC ALM WS I NPUT LOSS WS AI S RCVD WS AI S SEND WS OUTPUT LOSS TX CLK LOSS 1 TX CLK LOSS 2 RX CLK LOSS 1 RX CLK LOSS 2
C1 OUT
C2 OUT
OUT
OUT
C3
C4
C5
C6
OUT OUT
OUT OUT
OUT
OUT
OUT
OUT
C1
C2
C4
C5
C6
C3 OUT
OUT
OUT
OUT
Pr ess any key t o cont i nue…
12. Al ar mt abl e 2/ 3 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27.
FSYNC ALM1 FSYNC ALM2 HI GH BER ALM 1 HI GH BER ALM 2 LOWBER ALM 1 LOWBER ALM 2 BER ALM1 BER ALM2 MOD ALM 1 MOD ALM 2 DEMALM1 DEMALM2 OPR ALM1 OPR ALM2
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
Pr ess any key t o cont i nue…
3-52
OUT
OUT
OUT OUT
OPERATION
ROI-S04488
Step
Procedure
12. Al ar mt abl e 3/ 3 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44.
TX PWR ALM 1 TX PWR ALM 2 RX LEV ALM 1 RX LEV ALM 2 APC1 ALM1 APC1 ALM2 APC2 ALM1 APC2 ALM2 I F I NPUT ALM1 I F I NPUT ALM2 MAI NT TX SEL 1 TX SEL 2 RX SEL 1 RX SEL 2 MDP CPU ALM 1 MDP CPU ALM 2
C1 OUT
OUT
OUT
C2
C3
C4
C5
C6
OUT
OUT
OUT
OUT
OUT
OUT
OUT MASK MASK MASK MASK MASK
OUT
OUT
OUT
OUT
OUT
Sel ect i t em No. ( 1- 44, 0: no change) :
Notes: 1. Alarm table displayed on the LCT depends on system configuration. 2. C1 to C6 will appear on the ALM terminals. C1: 1, 2 and 3 pins C2: 4, 5 and 6 pins C3: 7, 8 and 9 pins C4: 10, 11 and 12 pins C5: 20, 21 and 22 pins C6: 23, 24 and 25 pins 3. The items which are applied alarm output are indicated with “OUT” and not applied alarm output are indicated with “–”. 4. Selecting item No. changes depending on the mounted modules. 5. The outputs which are inhibited under maintenance conditions are indicated with "MASK". 50
Enter item No. and press the “Enter” key for setting, if not, press the “0” key and “Enter” key to go back to the Setting menu,
3-53
OPERATION
ROI-S04488
Step
51
Procedure
When press the “1” key and “Enter” key in previous step 50, following Form setting for Item No.1 is displayed, For 1+0 System
Sel ect i t em No. ( 1- 23, 0: no change) : 1 1.
I NPUT L OSS
For mC1 OUT
Sel ect For m C No. ( 1- 4)
For mC2
For mC3
For mC4
:
For 1+1 system Sel ect i t em No. ( 1- 43, 0: no change) : 1 1.
C1 OUT
I NPUT L OSS
C2 OUT
Sel ect For m C No. ( 1- 6)
C3
C4
C5
C6
:
52
Press any “1” to “4” (or “1” to “6” for 1+1) key for corresponding Form No. and “Enter” key,
53
When the “1” key and “Enter” key is pressed in previous step 52, following confirmation is displayed, For 1+0 System
Sel ect For m C No. ( 1- 4) 1.
I NPUT L OSS
:1
For mC1 OUT
For mC2
For mC3
For mC4
For m C1 ( out put - no: 0 / yes: 1) :
For 1+1 System Sel ect For m C No. ( 1- 6) 1.
I NPUT L OSS
:1 C1 OUT
For m C1 ( out put - no: 0/ yes : 1)
3-54
C2 OUT :
C3
C4
C5
C6
OPERATION
ROI-S04488
Step
Procedure
54
Press the “1” key and “Enter” key for setting, or press the “0” key and “Enter” key for cancel,
55
When pressed the “0” key and “Enter” key in previous step 54, following setting for other Form is displayed, For 1+0 System
For m C1 ( o ut put - no: 0/ yes : 1) 1.
I NPUT L OSS
:0
For mC1
For mC2
For mC3
For mC4
Ot her For m C sel ect ? ( no: 0 / For m C No. : 1- 4) :
For 1+1 System For m C1 ( out put - no: 0/ yes : 1) 1.
I NPUT L OSS
:0
C1
C2
C3
C4
C5
C6
Ot her For m C sel ect? ( no: 0/ For m C No. : 1- 6) :
56
Press any “1” to “4” (or “1” to “6” for 1+1) key for corresponding Form No. and “Enter” key for setting, or “0” key and “Enter” key for cancel, For 1+0 System
Ot her For m C sel ect ? ( no: 0 / For m C No. : 1- 4)
:0
Ot her i t em s el ec t ? ( no: 0 / i t em No. : 1- 23) :
For 1+1 System Ot her For m C sel ect ? ( no: 0/ For m C No. : 1- 6)
:0
Ot her i t em s el ec t ? ( no: 0/ i t em No. : 1- 44) :
57
Press the “2” key and “Enter” key. Repeat steps 52 to 56 for items of 2 to 23 (or 2 to 44 for 1+1) in step 48 for alarm setting, if not, press the “0” key and “Enter” key for cancel,
58
Press the “Esc” key, to go back to Setting menu,
59
On the Setting menu, press the “1”, “4” keys and press the “Enter” key, then, following “Next items” is dis played,
3-55
OPERATION
ROI-S04488
Step
Procedure
For 1+0 System 14. Next i t ems 1. 2. 00. 99.
LAN set t i ng Channel us age er r or ( r epor t ) Menu Exi t
Sel ec t i t em No. :
Note: When the LAN INTFC is not mounted, “LAN setting” is not displayed . Note: If bitrate is changed after a setup of LAN, the contents of a setting will be cleared and it will return to Not used. For 1+1 System 14. Next i t em 1. 2. 3. 00. 99.
Syst emconf i gur at i on ( Hot st andby) LAN set t i ng Channel us age er r or ( r epor t ) Menu Exi t
Sel ec t i t em No. :
60
1.
In 1+1 system, press the “1” key and “Enter” key, then, following “Syst em conf i gur at i on” is displayed,
Syst emconf i gur at i on ( Hot st andby)
Syst em conf i gur at i on ( 1+0 expandabl e : 0/ Hot st andby: 1/ Twi n pat h: 2) :
Notes: 1. When changing the system from Twinpath to Hot standby, hand over the setting parameter of No. 1 CH to No. 2 CH. 2. When changing the system from 1+0 to Twinpath or from Hot standby to Twinpath, first set the frequency of No.2 CH to 0ch and change the “System configuration” after 1sec. or later.
3-56
61
In 1+1 system, press the “0” key, “1” key or “2” key and “Enter” key,
62
Press the “1” key (or “2” key for 1+1) and “Enter” key on the, key, then, following item is displayed,
OPERATION
ROI-S04488
Step
Procedure
For 1+0 System 1.
LAN set t i ng 1. 2. 3. 00. 99.
Por t 1 s et t i ng ( 16M) Por t 2 s et t i ng ( 2M) FE l i nk down ( di s abl e) Menu Exi t
Sel ec t i t em No. :
For 1+1 System 2.
LAN Set t i ng 1. 2. 3. 00. 99.
Por t 1 s et t i ng ( 16M) Por t 2 s et t i ng ( 2M) FE l i nk down ( di s abl e) Menu Exi t
Sel ec t i t em No. :
Note: Setting of the LAN signal assignment for Port1 and Port2 is referred to Table 3-3. 63
1.
Press the “1” key for Port1 setting (or “2” key for Port2 setting) and “Enter” key, then, following Port1 setting items are displayed,
Por t 1 set t i ng 1. 2. 3. 4. 5. 6. 7. 00. 99.
Thr oughput Mode Fl ow ct r l Fr ami ng CAS CRC Col l i si on r epor t Menu Exi t
( 2M) ( AUTONEG( AUTO- MDI / MDI X) ( on) ( on) ( on) ( on) ( r epor t )
Sel ec t i t em No. :
Notes: 1. “ Framing ” is displayed only when the “Throughput ” bit rate is set to 2M. 2. “CAS ” and “CRC ” are “ Framing ” is set to “off”.
not
indicated
when
3-57
OPERATION
ROI-S04488
Table 3-3 Applicable Traffic Channel System
2 x 2MB
4 x 2MB
8 x 2MB
16 x 2MB
3-58
(10/100BASE-T) Port 1
Port 2
disable 2M 2M 4M disable 2M 2M 4M 4M 4M 8M disable 2M 2M 4M 4M 4M 8M 8M 8M 8M 16M
disable disable 2M disable disable disable 2M disable 2M 4M disable disable disable 2M disable 2M 4M disable 2M 4M 8M disable
disable
disable
2M
disable
2M
2M
4M
disable
4M
2M
4M 8M 8M 8M 8M 16M 16M 16M 16M 16M 32M
4M disable 2M 4M 8M disable 2M 4M 8M 16M disable
Applicable Traffic CH Number to use 2MB CH1, CH2 CH2 − − CH1, CH2, CH3, CH4 CH2, CH3, CH4 CH2, CH4 CH3, CH4 CH4 − − CH1, CH2, CH3, CH4, CH5, CH6, CH7, CH8 CH2, CH3, CH4, CH5, CH6, CH7, CH8 CH2, CH3, CH4, CH6, CH7, CH8 CH3, CH4, CH5, CH6, CH7, CH8 CH3, CH4, CH6, CH7, CH8 CH3, CH4, CH7, CH8 CH5, CH6, CH7, CH8 CH6, CH7, CH8 CH7, CH8 − − CH1, CH2, CH3, CH4, CH5, CH6, CH7, CH8, CH9, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH2, CH3, CH4, CH5, CH6, CH7, CH8, CH9, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH2, CH3, CH4, CH5, CH6, CH7, CH8, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH3, CH4, CH5, CH6, CH7, CH8, CH9, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH3, CH4, CH5, CH6, CH7, CH8, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH3, CH4, CH5, CH6, CH7, CH8, CH11, CH12, CH13, CH14, CH15, CH16 CH5, CH6, CH7, CH8, CH9, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH5, CH6, CH7, CH8, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH5, CH6, CH7, CH8, CH11, CH12, CH13, CH14, CH15, CH16 CH5, CH6, CH7, CH8, CH13, CH14, CH15, CH16 CH9, CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH10, CH11, CH12, CH13, CH14, CH15, CH16 CH11, CH12, CH13, CH14, CH15, CH16 CH13, CH14, CH15, CH16 − −
OPERATION
ROI-S04488
Step
Procedure
64
1.
Press the “1” key and “Enter” key, then, following item is displayed,
Thr oughput ( 2M)
Thr oughput ( di sabl e: 0 / 2M: 1 / 4M: 2 / 8M: 3 / 16M: 4 / 32M: 5) :
Notes: 1. The E1 channels are restricted depending on the throughput bit rate assignment of the LAN Port 1 and port 2. (see Table 3-3) 2. The throughput bit rate for the Port 2 must be set less than Port 1 or the same value with Port 1. (i.e. Port 1 < Port 2 are not applicable). (see Table 3-3) 3. Full bandwidth assignment of the throughput for Port 2 is not applicable. (e.g. Port 1: disable, Port 2: 4M in 2 x 2MB system) (see Table 3-3). 65
Press any “0” to “5” key and “Enter” key,
66
Press the “2” key and “Enter” key on the “ Por t 1 Set t i ng” menu, then, following menu is displayed,
2.
Mode
( AUTONEG( AUTO- MDI / MDI X)
Mode AUTONEG( AUTO- MDI / MDI X) : 0 10M- HALF( MDI ) : 1 / 10M- FULL( MDI ) : 2 100M- HALF( MDI ) : 3 / 100M- FULL( MDI ) : 4 10M- HALF( MDI X) : 5 / 10M- FULL( MDI X) : 6 100M- HALF( MDI X) : 7 / 100M- FULL( MDI X) : 8 Sel ec t i t em No. :
67
Press any “0” to “8” key of the desired mode and “Enter” key,
68
Press the “3” key and “Enter” key on the “ Por t 1 Set t i ng” menu, then, following item is displayed,
3.
Fl ow ct r l ( of f )
Fl ow ct r l
69
( of f : 0 / on: 1) :
Press the “0” or “1” key and “Enter” key for setting,
3-59
OPERATION
ROI-S04488
Step
70
4.
Procedure
When 2M is applied for throughput bit rate, press the “4” key and “Enter” key on the “ Por t 1 Set t i ng” menu, following item is displayed, Fr ami ng ( of f )
Frami ng ( of f : 0 / on: 1) :
71
Press the “0” or “1” key and “Enter” key for setting, Note: When “1” is selected, G.704 E1 formatting is applied to the LAN signal.
72
5.
Press the “5” key and “Enter” key on the “ Por t 1 set t i ng” menu, when “1” is selected for Framing on, following item is displayed, CAS ( on)
CAS ( of f : 0 / on: 1) :
Note: When “0” is selected, LAN data signal is multiplexed including the CAS channel area, but if “1” is selected, LAN data signal is multiplexed excluding the CAS channel area. 73
Press the “0” or “1” key and “Enter” key for setting,
74
Press the “6” key and “Enter” key on the “ Por t 1 set t i ng” menu, when “1” is selected for Framing on, then, following item is displayed,
6.
CRC ( on)
CRC ( of f : 0 / on: 1) :
75
Press the “0” or “1” key and “Enter” key for setting,
76
Press the “7” key and “Enter” key on the “ Por t 1 set t i ng” menu, the following item is displayed,
7.
Col l i si on r epor t ( r epor t )
Col l i s i on r epor t ( r epor t : 0 / not r epor t : 1) :
3-60
OPERATION
ROI-S04488
Step
Procedure
77
Press the “0” or “1” key and “Enter” key for setting, press the “Esc” key to go back to the LAN setting menu, then perform setting for Port2,
78
Press the “Esc” key to go back to the LAN setting menu, and press the “3” key and “Enter” key, then, following item is displayed,
3.
FE l i nk down ( di s abl e)
FE l i nk down (di sabl e: 0 / enabl e: 1) :
Note: The local LAN port is shut off by the radio system alarm or far-end LAN Link failure, when “enable” is selected. 79
Press the “0” or “1” key and “Enter” key,
80
Press twice the “Esc” key to go back to the Next items menu shown in step 59,
81
Press corresponding number key for “Channel usage error” item and “Enter” key, then, the following is displayed,
2.
Channel us age er r or ( r epor t )
Channel usage er r or ( r epor t : 0 / not r epor t : 1) :
82
Press the “0” or “1” key and “Enter” key for setting, Note: This setting is effected for both Main channel usage error and WS channel usage error.
83
Press the “9”, “9” key and press the “Enter” key to exit the LCT menu.
3-61
OPERATION
ROI-S04488
3.4.2 Alarm/Status Monitoring Procedure from LCT Alarm conditions are identified by the IDU indicator on the IDU. Also the working conditions of the IDU and ODU can be monitored by the PC, as follows: Step
Procedure
1
Connect the personal computer (PC) to the LA PORT of the IDU using an RS-232C cable as shown in Fig. 3-7,
2
Turn on the power on the PC. Then, start the communication software (e.g. HyperTerminal), Note: At the end of LCT operation log out from LCT menu by keying "99" and then exit from the communication software. In case if you have exit from the communication software without logging out from LCT, repeat connecting and disconnecting of the RS 232C cable once to reset.
3
Press the “CTRL” and “D” keys at the same time,
4
Enter the specified password from the keyboard and press the “Enter” key,
Passwor d
5
:
Press the “0” key and “Enter” key,
Passwor d : ******** Change Passwor d? ( no: 0 / yes: 1) :
6 1. 2. 3. 99.
Following menu items are displayed, Set t i ng Mai nt enanc e Moni t or i ng Exi t
Sel ect f unct i on No. :
7
3-62
Press the “3” key and “Enter” key, then, following menu is displayed,
OPERATION
ROI-S04488
Step
Procedure
For 1+0 System Moni t or i ng 1. Moni t or i ng vol t age 2. Moni t or i ng vol t age (cont i nuous mode) 3. Al ar m/ St at us 4. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
For 1+1 System Moni t or i ng 1. Moni t or i ng vol t age 2. Al ar m/ St at us 3. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
3-63
OPERATION
ROI-S04488
Step
Procedure
Alarm and Status 8
Press the “3” for 1+0 (or “2” for 1+1) key and “Enter” key, then, following alarm items are displayed, For 1+0 System
3.
Moni t or i ng of al ar m/ s t at us 1/ 2 I DU I NPUT LOSS 1- 16 ( al ar m: **** - - - CHANNEL USAGE ERROR 1- 16 ( al ar m: **** - - - AI S RCVD 1- 16 ( al ar m: - - - - - - - AI S SEND 1- 16 ( al ar m: **** - - - OUTPUT LOSS 1- 16 ( al ar m: - - - - - - - LAN I NTFC ALM ( al ar m: - ) WS I NPUT LOSS ( al ar m: - ) WS CHANNEL USAGE ERROR ( al ar m: - ) WS AI S RCVD ( al ar m: - ) WS AI S SEND ( al ar m: - ) WS OUTPUT LOSS ( al ar m: - ) TX CLK LOSS ( al ar m: - ) FSYNC ALM ( al ar m: * ) HI GH BER ALM ( al ar m: * ) LOWBER ALM ( al ar m: * ) BER ALM ( al ar m: * )
------------- - --
----) ----) ----) ----) ----)
Pr ess any key t o cont i nue …
Notes:
3-64
1. “*” : indicates alarm condition. 2. “–” : indicates normal condition. 3. Monitoring of alarm/status displayed on the LCT depend on system configuration. 4. CHANNEL USAGE ERROR 1-16 is displayed only when “Channel usage error” is selected to “report”. 5. WS CHANNEL USAGE ERROR is not displayed when “Channel usage error” is selected to “not report”.
OPERATION
ROI-S04488
Step
3.
Procedure
Moni t or i ng of al ar m/ s t at us 2/ 2 MOD ALM ( al ar m: - ) DEM ALM ( al ar m: *) OPR ALM ( al ar m: *) ODU TX PWR ALM RX LEV ALM APC1 ALM APC2 ALM I F I NPUT ALM MUTE TX/ RX FREQ CH
( al ( al ( al ( al ( al
ar m: - ) ar m: - ) ar m: - ) ar m: - ) ar m: - )
( of f ) ( 5ch)
Pr ess any key
Notes:
1. “*” : indicates alarm condition. 2. “–” : indicates normal condition. 3. “5ch” : RF channel number is displayed.
For 1+1 System 2.
Moni t or i ng of al ar m/ s t at us 1/ 2 I DU I NPUT LOSS 1- 16 ( al ar m: - - - - - - - CHANNEL USAGE ERROR 1- 16 ( al ar m: **** - - - AI S RCVD 1- 16 ( al ar m: - - - - - - - AI S SEND 1- 16 ( al ar m: - - - - - - - OUTPUT LOSS 1- 16 ( al ar m: - - - - - - - LAN I NTFC ALM ( al ar m: - ) WS I NPUT LOSS ( al ar m: - ) WS CHANNEL USAGE ERROR ( al arm: - ) WS AI S RCVD ( al ar m: - ) WS AI S SEND ( al ar m: - ) WS OUTPUT LOSS ( al ar m: - ) TX CLK LOSS( No. 1/ No. 2) ( al ar m: - / - ) RX CLK LOSS( No. 1/ No. 2) ( al ar m: - / - ) FSYNC ALM( No. 1/ No. 2) ( al ar m: - / - ) HI GH BER ALM( No. 1/ No. 2) ( al ar m: - / - ) LOWBER ALM( No. 1/ No. 2) ( al ar m: - / - ) BER ALM( No. 1/ No. 2) ( al ar m: - / - )
- -- ---------- - --
) ----) ----) ----) - -- - ) ****
Pr ess any key t o cont i nue …
3-65
OPERATION
ROI-S04488
Step
Procedure
Notes: 1. “∗” : indicates alarm condition. 2. “−” : indicates normal condition. 3. Monitoring of alarm/status displayed on the LCT depend on system configuration. 4. CHANNEL USAGE ERROR 1-16 is displayed only when “Channel usage error” is selected to “report”. 5. WS CHANNEL USAGE ERROR is not displayed when “Channel usage error” is selected to “not report” . 2.
Moni t or i ng of al ar m/ s t at us 2/ 2 MOD ALM( No. 1/ No. 2) ( al ar m: - / - ) DEM ALM( No. 1/ No. 2) ( al ar m: - / *) OPR ALM( No. 1/ No. 2) ( al ar m: - / *) MDP CPU AL M( No. 1/ No. 2) ( al ar m: - / *) ODU TX PWR ALM( No. 1/ No. 2) ( al ar m: - / - ) RX LEV ALM( No. 1/ No. 2) ( al ar m: - / - ) APC1 ALM( No. 1/ No. 2) ( al ar m: - / - ) APC2 ALM( No. 1/ No. 2) ( al ar m: - / - ) I F I NPUT ALM( No. 1/ No. 2) ( al ar m: - / - ) MUTE No. 1 MUTE No. 2 TX/ RX FREQ CH
( of f ) ( on) ( 5ch)
Pr ess any key
Notes: 1. “∗” indicates alarm condition. 2. “−” indicates normal condition. 3. “5 ch” indication shows setting channel number. The LCT display sample shows Hot standby system. In Twin path system, it is displayed as follows: TX/RX FREQ. CH No.1 (0 ch) TX/RX FREQ. CH No.2 (0 ch) 4. Monitoring of alarm/status displayed on the LCT depend on system configuration. 9
3-66
Press any key to go back to the Monitoring menu,
OPERATION
ROI-S04488
Step
Procedure
For 1+0 System Moni t or i ng 1. Moni t or i ng vol t age 2. Moni t or i ng vol t age (cont i nuous mode) 3. Al ar m/ St at us 4. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
For 1+1 System Moni t or i ng 1. Moni t or i ng vol t age 2. Al ar m/ St at us 3. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
10
Press “4” key (or “3” key for 1+1) and “Enter” key, then, following item is displayed, For 1+0 System
4.
I nvent or y 1/ 2 I DU Ser i al number Manuf act ur ed dat e Sof t war e ver s i on ( ROM/ RAM) Bi t r at e Opt i on modul e
123456 MAY/ 2003 1. 20/ 2. 32 16 x 2MB PM CARD LAN I NTFC WS I NTFC 64k I NTFC( G. 703) 64k I NTFC( V11) ASC I NTFC DSC I NTFC ALM I NTFC SC LAN I NTFC
Pr ess any key t o cont i nue …
Note:
Only the mounted modules are indicated as optional module.
3-67
OPERATION
ROI-S04488
Step
4.
Procedure
I nvent or y 2/ 2 ODU Ser i al number Manuf act ur ed dat a Sof t war e ver si on ( ROM/ RAM) Bi t r at e RF band Sub band St ar t f r equency Shi f t f r equency CH separ at i on
23456 J AN/ 2003 1. 04/ 1. 04 17/ 34MB 18GHz Low A 17876. 250 MHz 1010 MHz 1. 25 MHz
Pr ess any key
For 1+1 System 3. I nvent or y 1/ 4 I DU SWUNI T Ser i al number Manuf act ur ed dat e Sof t ware vers i on ( ROM/ RAM) Bi t r at e Opt i on panel
123456 OCT/ 2002 1. 20/ 2. 19 16 x 2MB PM CARD LAN I NTFC WS I NTFC 64k I NTFC( G. 703) 64k I NTFC( V. 11) ASC I NTFC DSC I NTFC ALM I NTFC SC LAN I NTFC
Pr ess any key t o cont i nue …
Note: Only the mounted modules are indicated as optional module. 3. I nvent or y 2/ 4 I DU No. 1 MD UNI T Ser i al number Manuf act ur ed dat e Sof t ware vers i on ( ROM/ RAM) No. 2 MD UNI T Ser i al number Manuf act ur ed dat e Sof t ware vers i on ( ROM/ RAM) Pr ess any key t o cont i nue …
3-68
123456 SEP/ 2002 1. 20/ 2. 32 123457 SEP/ 2002 1. 20/ 2. 32
OPERATION
ROI-S04488
Step
Procedure
3. I nvent or y 3/ 4 ODU No. 1 ODU Ser i al number Manuf act ur ed dat e Sof t war e ver si on ( ROM/ RAM) Bi t r at e RF band Sub band St ar t f r equency Shi f t f r equency CH separ at i on
456 J AN/ 2003 1. 04/ 1. 04 17/ 34MB 18GHz Hi gh A 18538. 750MHz 1010MHz 1. 25MHz
Pr ess any key t o cont i nue …
3. I nvent or y 4/ 4 ODU No. 2 ODU Ser i al number Manuf act ur ed dat e Sof t war e ver s i on ( ROM) Bi t r at e RF band Sub band St ar t f r equency Shi f t f r equency CH separ at i on
457 SEP/ 2002 1. 04 17/ 34MB 18GHz Hi gh A 18538. 750MHz 1010MHz 1. 25MHz
Pr ess any key
11
Press any key to go back to the Monitoring menu, then, press the “9”,“9” keys to exit the monitoring of the Pasolink.
Moni t or i ng 1. Moni t or i ng vol t age 2. Moni t or i ng vol t age (cont i nuous mode) 3. Al ar m/ St at us 4. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
3-69
OPERATION
ROI-S04488
3.4.3 Monitoring Voltage of the ODU The following items of the ODU can be monitored on the PC. • Transmitter output power • Received signal level The procedure is as follows: Step
Procedure
1
Connect the personal computer (PC) to the LA PORT of the IDU using an RS-232C cable as shown in Fig. 3-7,
2
Turn on the power on the PC. Then, start the communication software (e.g. HyperTerminal), Note: At the end of LCT operation log out from LCT menu by keying "99" and then exit from the communication software. In case if you have exit from the communication software without logging out from LCT, repeat connecting and disconnecting of the RS 232C cable once to reset.
3
Press the “CTRL” and “D” keys at the same time,
4
Enter the specified password from the keyboard and press the “Enter” key,
Passwor d
5
:
Press the “0” key and “Enter” key,
Passwor d : ******** Change Passwor d? ( no: 0 / yes: 1) :
6 1. 2. 3. 99.
Following menu items are displayed, Set t i ng Mai nt enanc e Moni t or i ng Exi t
Sel ect f unct i on No. :
3-70
OPERATION
ROI-S04488
Step
7
Procedure
Press the “3” key and “Enter” key, then, following menu is displayed, For 1+0 System
Moni t or i ng 1. Moni t or i ng vol t age 2. Moni t or i ng vol t age (cont i nuous mode) 3. Al ar m/ St at us 4. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
For 1+1 System Moni t or i ng 1. Moni t or i ng vol t age 2. Al ar m/ St at us 3. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
8
Press the “1” key and “Enter” key, then, following item is displayed, Note: In normal operation, the voltages indicated should be within the values as shown in table 3-4. (The allowable range of the meter reading is referred to Table 4-2 in Section II TRP Equipment Description, Maintenance.) For 1+0 System
1.
Moni t or i ng vol t age TX power RX l evel
: 4. 33V ( *1) : 3. 55V ( *1)
For 1+1 System 1.
Moni t or i ng vol t age TX power 1 RX l evel 1 TX power 2 RX l evel 2
: : : :
4. 33V 2. 98V 4. 33V 2. 18V
( *1) ( *1) ( *1) ( *1)
3-71
OPERATION
ROI-S04488
Step
Procedure
Note: *1 TX power is indicated in dB and RX level is in dBm in parenthesis with voltage depending on the ODU type. The TX power indicated in dB is a relative level to the nominal output power. 9
Press the “Esc” key to go back to the Monitoring menu, then, press the “9”, “9” keys to exit the monitoring of the Pasolink. For 1+0 System
Moni t or i ng 1. Moni t or i ng vol t age 2. Moni t or i ng vol t age (cont i nuous mode) 3. Al ar m/ St at us 4. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
For 1+1 System Moni t or i ng 1. Moni t or i ng vol t age 2. Al ar m/ St at us 3. I nvent or y 00. Menu 99. Exi t Sel ec t i t em No. :
3-72
OPERATION
ROI-S04488
Table 3-4 Meter Reading of IDU and ODU CHECK ITEM
ALLOWABLE RANGE
TX power
Depends on transmitter power and the ODU type • 0 to 4.1 V DC (for 7/8 GHz ODU)*1 • 0 to 4.6 V DC (for 13-38 GHz ODU)*2 • 0 to 4.6 V DC (for 7-38 GHz ODU)*3
RX level
Depends on received signal level and the ODU type • 0.2 to 4.2 V DC (for 7/8 GHz ODU)*1 • 0.2 to 4.5 V DC (for 13-38 GHz ODU)*2 • 0.8 to 4.4 V DC (for 7-38 GHz ODU)*3 Notes:
*1 The code number of corresponding 7/8 GHz ODUs are as follows. • G6583 • G6584 • G6585 • G6586 *2 The code number of corresponding 13-38 GHz ODUs are as follows. • G2924 • G3359 • G5380 • G5383 • G5384 • G6594 *3 The code number of corresponding 7-38 GHz ODUs are as follows. • H0330 • H0331 • H0332 • H0333 • H0334 • H0335 • H0738 • H0739
3-73
OPERATION
ROI-S04488
(This page is intentionally left blank.)
3-74 74 pages
MAINTENANCE
ROI-S04488
4. MAINTENANCE This section provides instructions for periodic maintenance and corrective maintenance of the IDU. Also included is information on precautions, test equipment and accessories.
4.1 Precautions The following maintenance.
precautions
must
be
carefully
observed
during
1. The −43 V DC power is superimposed on the centre conductor of the coaxial cable between the IDU and ODU. Connecting a measurement set directly may damage the test equipment and touching the coaxial cable core may cause electrical shock. So, power down IDU before disconnection or connection of cable. 2. To protect the internal circuits against electrostatic discharge, engineers are requested to wear a wrist band and connect it to the frame ground terminal (FG) for Electrostatic Discharge (ESD) before detaching the shield cover (see Fig. 4-1). 3. Before the start of maintenance, including operation of the OPR SEL SW on the front panel of the equipment, select the equipment to maintenance mode using the LCT. After all operation for maintenance have been completed, perform MAINT OFF setting. 4. Do not turn on the power of the IDU leaving cable connection between the PC and RA PORT of the IDU. 5. Replacing the IDU, if new IDU has a history to be used in other hop, the new IDU may has former frequency channel setting and may make the ODU to transmit in an undesired TX frequency. NEC recommend to set the frequency channel before connecting the ODU.
4-1
MAINTENANCE
ROI-S04488
IF IN/OUT
(IDU for 1+0 System)
Connect the wrist strap. (FG to be used as ESD)
IF IN/OUT
!
-43V OUTPUT
PowerdownIDU beforedisconnection orconnectionof Cable
TRAFFIC IN/OUT (CH9 to CH16)
(IDU for 1+1 System) TRAFFIC IN/OUT (CH1 to CH8)
IF IN/OUT
!
-43V OUTPUT
PowerdownIDU beforedisconnection orconnectionof Cable
Fig. 4-1 Location of the Frame Ground Terminal for ESD
(a)
Before beginning maintenance, notify the opposite station that maintenance is about to begin.
(b) After equipment start-up, allow the equipment to warm up for at least 30 minutes. (c)
After completing the maintenance operation, restore all connections to normal.
(d) In 1+1 system, to power ON the IDU, take the following steps. (1) When neither channel No.1 nor No.2 are working, first set the OPR SEL switch to the desired (No.1 or No.2) position and power on the selected MD unit or set the OPE SEL switch to neutral (Auto) position and power on both MD units. (2) When either channel No.1 or No.2 is working, set the OPR SEL No.1-No.2 switch on the IDU to the working channel side, then, turn on the power switch of the not working channel. (e)
During maintenance, the IDU is set to maintenance condition using a PC as described in 4.2 Maintenance Condition Setting:
Caution:
4-2
If login is not possible, check if settings of the communication format are proper.
MAINTENANCE
ROI-S04488
4.2 Maintenance Control from LCT Step
Procedure
1
Connect the PC to the LA PORT of the IDU using an RS-232C cable as shown in Fig. 3-7,
2
Turn on the power switch on the PC. Then, operate the communication software (e.g. HyperTerminal), Note: At the end of LCT operation log out from LCT menu by keying "99" and then exit from the communication software. In case if you have exit from the communication software without logging out from LCT, repeat connecting and disconnecting of the RS 232C cable once to reset.
3
Press the “CTRL” and “D” keys at the same time,
4
Enter the specified password from the keyboard, and press the “Enter” key,
Passwor d
5
:
Press the “0” key and “Enter” key,
Passwor d : ******** Change Passwor d? ( no: 0/ yes: 1) :
6 1. 2. 3. 99.
The following menu is then displayed, Set t i ng Mai nt enanc e Moni t or i ng Exi t
Sel ect f unct i on No.
7
:
Press the “2” key and “Enter” key, then, following item is displayed,
4-3
MAINTENANCE
ROI-S04488
Step
Procedure
For 1+0 System Mai nt enance 1. MAI NT 2. FE l oop back ct r l 1- 16 3.
NE l oop back ct r l 1- 16
4. 5. 6. 7. 00. 99.
BER ALM >> AI S CW Power mut e ATPC manual c t r l Menu Exi t
Sel ect i t em No.
( NORM) ( ct r l : *Z#( ans : *- - ( ct r l : *- #( ans : *- - ( on) ( of f ) ( of f ) ( of f )
- -- ----- -----
- -- ---- ------
- -- -) ----) --- -) ----)
-- ------ -----
-- ----- ------
-- -- ) ----) --- -) ----)
:
For 1+1 System
Mai nt enance 1. MAI NT 2. FE l oop back ct r l 1- 16 3.
NE l oop back ct r l 1- 16
4. 5. 6. 7. 8. 9. 10. 00. 99.
BER ALM >> AI S CW Power mut e 1 Power mut e 2 TX SWc t r l RX SWc t r l ATPC manual ct r l Menu Exi t
Sel ect i t em No.
( NORM) ( ct r l : *Z#( ans : *- - ( ct r l : *- #( ans : *- - ( on) ( of f ) ( of f ) ( on) ( AUTO) ( AUTO) ( of f )
:
Notes: 1. “-” indication signifies control off condition, 2. “*” indication signifies control on condition, 3. “#” signifies E1 channel which is inhibited by the hardware restriction or LAN signal transmission, 4. In case the FE loop back is applied from the opposite station, the “Z” is displayed, 5. The FE loopback control is unavailable if the channel is inhibited by “Not used” in Main channel usage. 6. Item ATPC manual ctrl is not displayed in MTPC mode.
4-4
MAINTENANCE
ROI-S04488
Step
8
1.
Procedure
Press the “1” key and “Enter” key, then, following item is displayed, MAI NT ( NORM)
MAI NT ( NORM: 0/ MAI NT: 1)
9
:1
Press the “1” key and “Enter” key, Then, the MAINT indicator on the IDU should light, For 1+0 System
Mai nt enance 1. MAI NT 2. FE l oop back ct r l 1- 16 3.
NE l oop back ct r l 1- 16
4. 5. 6. 7. 00. 99.
BER ALM >> AI S CW Power mut e ATPC manual c t r l Menu Exi t
Sel ect i t em No.
( MAI NT) ( ct r l : *Z#( ans : *- - ( ct r l : *- #( ans : *- - ( on) ( of f ) ( of f ) ( of f )
- -- ----- -----
- -- ---- ------
- -- -) ----) --- -) ----)
-- ------ -----
-- ----- ------
-- -- ) ----) --- -) ----)
:
For 1+1 System Mai nt enance 1. MAI NT 2. FE l oop back ct r l 1- 16 3.
NE l oop back ct r l 1- 16
4. 5. 6. 7. 8. 9. 10. 00. 99.
BER ALM >> AI S CW Power mut e 1 Power mut e 2 TX SWc t r l RX SWc t r l ATPC manual ct r l Menu Exi t
Sel ect i t em No.
( MAI NT) ( ct r l : *Z#( ans : *- - ( ct r l : *- #( ans : *- - ( on) ( of f ) ( of f ) ( on) ( AUTO) ( AUTO) ( of f )
:
4-5
MAINTENANCE
ROI-S04488
Step
10
2.
Procedure
Press the “2” key and “Enter” key in the Maintenance menu shown in step 9,
FE l oop back ct r l 1- 16 ( 1: on 2: of f 3: N/ A 4: of f 5: of f 6: of f 7: of f 8: of f 9: of f 10: of f 11: of f 12: of f 13: of f 14: of f 15: of f 16: of f )
Sel ect channel No. : 5
11
Press the “channel number you want to control” and “Enter” key, then, the following appears on the display, Note: The channel which is applied FE loop back from the opposite station, channel number can not be selected.
Sel ect channel No. : 5 Channel 5 ( of f : 0 / on: 1) :
3.
12
Press the “1” key for far-end loop back, if not, press the “0” key and “Enter” key, repeat step 14 for any channel sett ing,
13
Press the “3” key and “Enter” key in the Maintenance menu shown in step 9,
NE l oop bac k ct r l 1- 16 ( 1: on 2: of f 3: N/ A 4: of f 5: of f 6: of f 7: of f 8: of f 9: of f 10: of f 11: of f 12: of f 13: of f 14: of f 15: of f 16: of f )
Sel ect channel No. : 5
14
Press the “channel number you want to control” and “Enter” key, then, the following appears on the display,
Sel ect channel No. : 5 Channel 5 ( of f : 0 / on: 1) :
15
4-6
Press the “1” key for near-end loop back, if not, press the “0” key and “Enter” key, repeat step 14 for any channel setting,
MAINTENANCE
ROI-S04488
Step
16
4.
Procedure
Press the “4” key and “Enter” key in the Maintenance menu shown in step 9, BER ALM>> AI S ( of f )
BER ALM >> AI S
( of f : 0 / on: 1) :
17
Press the “1” key and “Enter” key for setting to include BER ALM for AIS, if not, press the “Esc” key,
18
Press the “5” key and “Enter” key in the Maintenance menu shown in step 9, For 1+0/ 1+1 Hot standby System
5.
CW( of f )
CW ( of f : 0 / on: 1) :
19
Press the “1” key and “Enter” key to apply unmodulated carrier signal transmission (used during test), if not, press the “Esc” key, For 1+1 Twin path System
5. 1. 2. 00. 99.
CW( No. 1: of f / No. 2: of f ) No. 1 CW( of f ) No. 2 CW( of f ) Menu Exi t
Sel ec t i t em No. :
20
Press the “1” key to select No.1 CW and “Enter” key,
Sel ect i t emNo.
:1
No. 1 CW ( of f : 0 / on: 1) :
21
Press the “1” key and “Enter” key to apply unmodulated carrier signal transmission (used during test), if not, press the “Esc” key,
22
Press the “2” key to select No.2 CW and “Enter” key, repeat step 21 for No.2 CW,
4-7
MAINTENANCE
ROI-S04488
Step
23
Procedure
Press the “6” key and “Enter” key in the Maintenance menu shown in step 9, For 1+0 System
6.
Power mut e ( of f )
Power mut e ( of f : 0 / on: 1) :
24
Press the “1” key and “Enter” key to mute TX power, if not, press the “Esc” key, For 1+1 System
25
Press the “6” key for No. 1CH or “7” key for No. 2CH and “Enter” key, then the following appears, For No. 1 CH ODU
6.
Power mut e 1 ( of f )
Power mut e ( of f : 0 / on: 1)
:
For No. 2 CH ODU 7.
Power mut e 2 ( of f )
Power mut e ( of f : 0 / on: 1)
26
Press the “1” key and “Enter” key to mute TX power, if not, press the “Esc” key,
27
Press the “8” key and “Enter” key for 1+1 Hot standby system, in the Maintenance menu shown in step 9
8.
TX SWc t r l ( AUTO)
TX SW ct r l ( AUTO: 0 / No. 1: 1 / No. 2: 2) :
28
4-8
Press the “1” key and “Enter” key for No.1 TX selection or the “2” key and “Enter” key for No.2 TX selection, if not, press the “Esc” key,
MAINTENANCE
ROI-S04488
Step
29
9.
Procedure
Press the “9” key and “Enter” key in the Maintenance menu shown in step 9, RX SWc t r l ( AUTO)
RX SW ct r l ( AUTO: 0 / No. 1: 1 / No. 2: 2) :
30
Press the “1” key and “Enter” key for No.1 RX selection or the “2” key and “Enter” key for No.2 RX selection, if not, press the “Esc” key,
31
Press the “7” key and “Enter” key for 1+0 system or “10” key and “Enter” key for 1+1 system, in the Maintenance menu shown in step 9,
For 1+0 /Hot standby System 10. ATPC manual ct r l ( of f ) ATPC manual ct r l ( of f : 0 / on: 1) :
32
Press the “1” key and “Enter” key for ATPC manual control, if not, press the “Esc” key,
ATPC manual ct r l ( of f : 0 / on: 1) : 1 ATPC cur r ent ( - 15dB) ATPC cur r ent ( - 30 t o 0dB) :
33
Enter attenuation value and “Enter” key,
For Twin path System 10. ATPC manual ctr l ( No. 1: of f / No. 2: of f ) 1. 2. 00. 99.
No. 1 ATPC manual ct r l ( of f ) No. 2 ATPC manual ct r l ( of f ) Menu Exi t
Sel ec t i t em No. :
4-9
MAINTENANCE
ROI-S04488
Step
34
1.
Procedure
Press the “1” key and “Enter” key for No.1 TX selection or the “2” key and “Enter” key for No.2 TX selection, if not, press the “Esc” key, No. 1 ATPC manual c t r l ( of f )
No. 1 ATPC manual ct r l ( of f : 0 / on: 1) :
2.
No. 2 ATPC manual c t r l ( of f )
No. 2 ATPC manual ct r l ( of f : 0 / on: 1) :
35
Press the “1” key and “Enter” key to ATPC manual control, if not, press the “Esc” key,
No. 1 ATPC manual ct r l ( of f : 0 / on: 1) : 1 ATPC cur r ent ( - 15dB) ATPC cur r ent ( - 30 t o 0dB) :
No. 2 ATPC manual ct r l ( of f : 0 / on: 1) : 1 ATPC cur r ent ( - 15dB) ATPC cur r ent ( - 30 t o 0dB) :
Note: 1. The MAX power must be set to a value larger than MIN power. 2. When the TX power control mode is changed from ATPC to MTPC, current value in ATPC is applied to the MTPC.
4-10
36
Enter attenuation value and “Enter” key,
37
Restore all setting items which are changed in maintenance in referring to step 4 to step 36,
MAINTENANCE
ROI-S04488
Step
Procedure
38
Press the “0” key and “Enter” key to reset status from maintenance to normal in step 8,
39
Then, MAINT indicator goes off, For 1+0 System
Mai nt enance 1. MAI NT 2. FE l oop back ct r l 1- 16 3.
NE l oop back ct r l 1- 16
4. 5. 6. 7. 00. 99.
BER ALM >> AI S CW Power mut e ATPC manual c t r l Menu Exi t
Sel ect i t em No.
( NORM) ( ct r l : *Z#( ans : *- - ( ct r l : *- #( ans : *- - ( on) ( of f ) ( of f ) ( of f )
- -- ----- -----
- -- ---- ------
- -- -) ----) --- -) ----)
-------------
-------------
----) ----) ----) ----)
:
For 1+1 System Mai nt enance 1. MAI NT 2. FE l oop back ct r l 1- 16 3.
NE l oop back ct r l 1- 16
4. 5. 6. 7. 8. 9. 10. 00. 99.
BER AI S ALM >> AI S CW Power mut e 1 Power mut e 2 TX SWc t r l RX SWc t r l ATPC manual ct r l Menu Exi t
Sel ect i t em No.
40
( NORM) ( ct r l : * Z#( ans : * - - ( ct r l : * - #( ans : * - - ( on) ( of f ) ( of f ) ( on) ( AUTO) ( AUTO) ( of f )
:
Press the “9”,“9” keys and press the “Enter” key to exit maintenance mode.
4-11
MAINTENANCE
ROI-S04488
4.3 Test Equipment and Accessories The test equipment and special accessories are required for system maintenance as described in Table 4-1. If recommended test equipment and accessories are not available, equivalents may be used. Table 4-1 Test Equipment and Accessories Required Test Equipment/Accessories
Digital Multimeter with Test Lest Leads
Type/Ordering Code
Agilent 34401A
Q’ty Req’d
1
Headset
———
1
Personal Computer
———
1
Screwdriver
———
1
4.4 Periodic Maintenance To ensure continued satisfactory operation of the equipment, perform the following maintenance procedure once a year. (a) Test Equipment and Accessories Required • Agilent 34401A Digital Multimeter with Test Leads • Screwdriver (b) Procedure Step
1
Procedure
Connect a digital multimeter to SELV (−) and SELV (+) terminals above the power cable input. Confirm that the meter indication is as described in Table 4-2, Table 4-2 Meter Reading Item
SELV (LINE IN)
Allowable Range
−20 to −60/+20 to +60 V DC
Note: The range of DC power input depends on system requirement.
4-12
MAINTENANCE
ROI-S04488
4.5 Corrective Maintenance Here, corrective maintenance in the field is described, and covers fault isolation, equipment replacement and alignment. When the equipment is faulty, it should be replaced with a spare. Replacement for the IDU is at the equipment-level in 1+0 system. Replacement for the IDU of 1+1 system is at panel-level (No.1, No.2 or SW unit) (see Fig. 4-2). During corrective maintenance, carefully observe the precautions given in paragraph 4.1 until alignment is completed.
4.5.1 Fault Isolation Flow Chart Alarm conditions are identified through: • Alarm LED (red) indication on the IDU or • Notification from external equipment During alarm conditions, red alarm LEDs on the IDU are lit except when there is a power supply failure. Faults can be isolated using the LED indicators on the front panel of the IDU. Table 4-4 provides information for isolating faults at a station. Connect the LCT to the equipment and check the equipment conditions in according with the flow chart are shown in Fig. 4-2 to Fig. 4-5. Refer to para. 3.4.2 for monitoring procedure using the LCT. Table 4-3 Fault Isolation by LED Indications on the IDU LED Indication
Fault Location
IDU ODU IDU/ODU (synchronous flashing) *
IDU ODU IF Cable between the IDU and ODU
Note *: When the IF cable between the IDU and ODU is e lectric short circuit condition or open condition, the IDU and ODU ALM LEDs are synchronously flashing. (If the TRP-( )G-5A ODU under Pasolink Mx mode is connected irregurarly, operation is not established with the ODU, a synchronous flashing condition will occur.)
4-13
M A I N T E N A N C E
4 -1 4
Table 4-4 Fault Isolation by LED Indications in 1+1 System LED INDICATION TX ALM 1
TX ALM 2
RX ALM 1
RX ALM 2
No. 1 IDU
No. 2 IDU
No. 1 ODU
No. 2 ODU
TX OPR 1
TX OPR 2
RX OPR 1
FAULT LOCATION
RX OPR 2
Modulator side of No. 1 CH MD unit of IDU Modulator side of No. 2 CH MD unit of IDU Demodulator side of No. 1 CH MD unit of IDU Demodulator side of No. 2 CH MD unit of IDU Transmitter side of No. 1 CH ODU Transmitter side of No. 2 CH ODU Receiver side of No. 1 CH ODU Receiver side of No. 2 CH ODU
SW unit of IDU
Note:
R O I S 0 4 4 8 8
LED indicators light. LED indicators light depending on the faulty condition.
MAINTENANCE
ROI-S04488
ODU TX Side Start
Is IF INPUT ALM issued? NO
YES
Is IF cable length within specified.
NO
Change the IF cable length or cable type to appropriate one.
NO
IF cable is poor conductor. Change the IF cable to new one.
YES
Is MOD ALM of IDU issued? YES
YES
Is IF INPUT ALM being issued? NO
IDU is failure. Replace the IDU with a spare.
ODU is failure. Replace the ODU with a spare.
MAINTENANCE
ROI-S04488
ODU TX Side Start
Is IF INPUT ALM issued?
YES
Is IF cable length within specified.
NO
Change the IF cable length or cable type to appropriate one.
NO
IF cable is poor conductor. Change the IF cable to new one.
YES
NO
Is MOD ALM of IDU issued? YES
YES
Is IF INPUT ALM being issued? NO
IDU is failure. Replace the IDU with a spare.
Is APC1 ALM or APC2 ALM issued?
YES
NO
Is setting of channel frequency assignment correct?
ODU is failure. Replace the ODU with a spare.
NO
Reset properly the channel frequency.
YES
ODU is failure. Replace the ODU with a spare.
Is TX PWR ALM issued?
YES
ODU is failure. Replace the ODU with a spare.
NO
Equipment is normal.
Fig. 4-2 ODU and TX ALM LEDs Lighting
4-15
MAINTENANCE
ROI-S04488
ODU RX Side Start
Is APC1 ALM or APC2 ALM issued?
YES
Is setting of channel frequency assignment correct?
NO
Reset properly the channel frequency.
NO
Check TX side of the ODU of the opposite site. Replace the ODU with a spare at the opposite site.
YES
NO
ODU is failure. Replace the ODU with a spare.
Is RX LEV ALM issued? NO
YES
Is operation of the ODU in the opposite site normal? YES
Is setting of channel frequency assignment correct?
NO
Reset properly the channel frequency.
YES
RX LEV MON voltage is less than 1 V?
YES
No failure of the equipment. Propagation problem.
NO
Equipment is normal.
The ODU is failure. Replace the ODU with a spare.
Fig. 4-3 ODU and RX ALM LEDs Lighting
4-16
MAINTENANCE
ROI-S04488
IDU TX Side Start
Is MOD ALM issued?
YES
The IDU is failure. Replace the IDU with a spare.
YES
The IDU is failure. Replace the IDU with a spare.
YES
The IDU is failure. Replace the IDU with a spare.
YES
The IDU is failure. Replace the IDU with a spare.
NO
Is TX DPU ALM issued? NO
Is TX CLK LOSS issued? NO
Is MUX ALM issued? NO
Is OPR ALM issued?
YES
Either IDU or ODU is failure. Try to replace the IDU or ODU with a spare.
NO
Is INPUT LOSS issued? NO
Equipment is normal.
YES
Is traffic interface cable connected properly? (Note *1)
NO
Correct the cable connection.
NO
Correct the impedance setting.
YES Is 75/120-ohm interface impedance set properly? YES
The IDU is failure. Replace the IDU with a spare.
Note *1: Check the interface cable as follows. (1) Cable is properly connected. (2) Cable length is within the specified. (3) It is conduct between cable ends.
Fig. 4-4 IDU and TX ALM LEDs Lighting
4-17
MAINTENANCE
ROI-S04488
IDU RX Side Start
Is DEM ALM issued?
YES
Is ODU operation normal?
NO
Check the RX side of the ODU.
NO
Set the Frame ID to the same number with the opposite IDU.
YES
NO
The IDU is failure. Replace the IDU with a spare.
Is FSYNC ALM issued?
YES
NO
Is BER ALM issued?
Is the Frame ID set to the same with the opposite IDU? YES
YES
No failure of the equipment. Propagation problem.
YES
The IDU is failure. Replace the IDU with a spare.
YES
The IDU is failure. Replace the IDU with a spare.
NO
Is RX CLK ALM issued? NO
Is OUTPUT LOSS issued? NO
Equipment is normal.
Fig. 4-5 IDU and RX ALM LEDs Lighting
4-18
MAINTENANCE
ROI-S04488
4.5.2 Replacement The Manufacturer does not recommend replacement of modules in the IDU (for 1+0 system) or Unit (for 1+1 system). Whenever a fault is identified on the IDU, the complete IDU equipment or Unit should be replaced with a spare. The faulty equipment is to be returned to the factory for repair. Whenever any unit fails in 1+1 system, replace only the unit that fails with a spare as described in procedures below. Caution: While the power supply is ON, do not remove/connect the power supply connector. Otherwise, the DC-DC CONV may fail. Caution: Before the start of maintenance, including operation of the OPR SEL SW on the front panel of the equipment, select the equipment to maintenance mode using the LCT. After all operation for maintenance have been completed, perform MAINT OFF setting. Caution: Do not disconnect IF cable between the IDU and the ODU in operating condition, if not, may damage the IDU and ODU. Do not remove/connect the IF cable with IDU power ON, turn IDU power OFF before remounting the IF cable. Caution: While the SW UNIT replacement is proceeding, the traffic is interrupted. Caution: It is recommended that you connect the IDU to ODU after the TX/RX frequency and TX power control setting has been set on the IDU. This process is most important for the following ODUs that may be emitted TX power if you set the channel number to "0ch" which is not defined (excepting 13/26/38 GHz band) by the Radio Frequency Assignment. Code No. of Corresponding ODU: H0738 (7 GHz), H0739 (8 GHz), H0330 (13 GHz), H0331 (15GHz), H0332 (18GHz), H0333 (23 GHz), H0334 (26 GHz), H0335 (38 GHz)
4-19
MAINTENANCE
ROI-S04488
Step
Procedure
No. 1 MD UNIT REPLACEMENT
Removing (see Fig. 4-6)
FIXTURE SCREW
Perform MAINT ON setting via the LCT,
2
Set the OPR SEL No. 1-No. 2 switch on the SW UNIT to No. 2,
3
Turn off the POWER SWITCH on the No. 1 MD UNIT,
4
Disconnect power supply cable from the LINE IN connector on the No. 1 MD UNIT,
5
Disconnect frame ground cable from the frame ground (FG) connector on the No. 1 MD UNIT,
6
Disconnect IF cable from the IF IN/OUT connector on the No. 1 MD UNIT,
7
Loosen two screws on the No. 1 MD UNIT,
8
Hold two fixtures and draw out the No. 1 MD UNIT from the IDU,
IF IN/OUT
! -43V OUTPUT
RESET PWR ODU IDU MAINT FUSE (7.5A)
PowerdownIDU beforedisconnecti on orconnection of Cable
SCREW FG
+
− SELV
LA PORT TRAFFIC IN/OUT (CH9 to CH16)
EOW CALL
PASOLINK RESET OPR SEL No.1
NMS LAN
OPR
ALM
AUX ALM
OW/DSC/ASC
NMS/RA
LA PORT
ALM 1 2
No.2
PASOLINK IF IN/OUT
! -43V OUTPUT
+
− LA PORT
IDU
No.2 CH POWER SWITCH
Fig. 4-6 Unit Replacement of 1+1 IDU
4-20
FIXTURE SCREW
RESET PWR ODU IDU MAINT FUSE (7.5A)
PowerdownIDU beforedisconnecti on orconnection of Cable
IF IN/OUT
LINE IN FIXTURE SCREW
TX RX TX RX
− TRAFFIC IN/OUT (CH1 to CH8)
FIXTURE SCREW
PASOLINK
SC LAN
FIXTURE
No.1 CH POWER SWITCH
OPR SEL No.1-No.2
IF IN/OUT
FIXTURE SCREW FG
1
SELV
LINE IN
MAINTENANCE
ROI-S04488
Step
Procedure
Remounting (see Fig. 4-6) 9
Fit a new unit to the guide rail at the location for mounting, then, push into the IDU along the guide rail until the multi-pin connector firmly connected,
10
Tighten two screws on the unit,
11
Reconnect IF cable to IF IN/OUT connector,
12
Reconnect power supply cable to the LINE IN connector,
13
Reconnect frame ground cable to the frame ground (FG) connector on the No. 1 MD UNIT,
14
Check that the OPR SEL No. 1-No. 2 switch on the SW UNIT is set to No. 2,
15
Turn on the POWER SWITCH on the No. 1 MD UNIT,
16
Perform MAINT OFF setting via the LCT. No. 2 MD UNIT REPLACEMENT
Removing (see Fig. 4-6) 1
Perform MAINT ON setting via the LCT,
2
Set the OPR SEL No. 1-No. 2 switch on the SW UNIT to No. 1,
3
Turn off the POWER SWITCH on the No. 2 MD UNIT,
4
Disconnect power supply cable from the LINE IN connector on the No. 2 CH MD UNIT,
5
Disconnect frame ground cable from the frame ground (FG) connector on the No. 2 MD UNIT,
6
Disconnect IF cable from the IF IN/OUT connector on the No. 2 MD UNIT,
7
Loosen two screws on the No. 2 MD UNIT,
8
Hold two fixtures and draw out the No. 2 MD UNIT from the IDU,
9
Fit a new unit to the guide rail at the location for mounting, then, push into the IDU along the guide rail until the multi-pin connector firmly connected,
4-21
MAINTENANCE
ROI-S04488
Step
Procedure
10
Tighten two screws on the unit,
11
Reconnect IF cable to IF IN/OUT connector,
12
Reconnect power supply cable to the LINE IN connector,
13
Check that the OPR SEL No. 1-No. 2 switch on the SW UNIT is set to No. 1,
14
Turn on the POWER SWITCH on the No. 2 MD UNIT
15
Perform MAINT OFF setting via the LCT. SW UNIT REPLACEMENT
Removing (see Fig. 4-6) 1
Turn off the power switch of No. 1 MD UNIT,
2
Turn off the power switch of No. 2 MD UNIT,
3
Disconnect all signal cables connected to the interface connectors on front of the SW UNIT,
4
Loosen two screws on the SW UNIT,
5
Hold two fixtures and draw out the SW UNIT from the IDU, Remounting (see Fig. 4-6)
4-22
1
Fit a new unit to the guide rail at the location for mounting, then, push into the IDU along the guide rail until the multi-pin connector firmly connected,
2
Tighten two screws on the unit,
3
Reconnect all signal cables to the interface connectors on front of the SW UNIT,
4
Set the OPR SEL No. 1-No. 2 switch on the SW UNIT to No. 1,
5
Turn on the POWER SWITCH on the No. 1 CH MD UNIT,
6
Turn on the POWER SWITCH on the No. 2 CH MD UNIT,
7
Set the OPR SEL No. 1-No. 2 switch on the SW UNIT to neutral position.
MAINTENANCE
ROI-S04488
4.5.3 Alignment After replacing the IDU with spare in 1+0 system, the IDU must be aligned with the PC setting. After replacing the SW UNIT with spare in 1+1 system, the IDU must be aligned with the PC setting. Caution: Allow equipment to warm up for at least 30 minutes before alignment.
(a) Test Equipment and Accessories Required • Personal Computer • Screwdriver (b) Procedure Step
Procedure
1
Referring to para. 3.4 in Section III, perform IDU equipment setting,
2
Referring to para. 3.4 in Section II, perform radio frequency and TX output power setting.
The working condition of the IDU/ODU can be monitored by the LCT. Refer to para. 3.4.2 for monitoring in Section III. Note: At the end of LCT operation log out from LCT menu by keying "99" and then exit from the communication software. In case if you have exit from the communication software without logging out from LCT, repeat connecting and disconnecting of the RS 232C cable once to reset. Note: For maintenance, record the inventory date of the IDU/ODU.
4-23
MAINTENANCE
ROI-S04488
(This page is intentionally left blank.)
4-24 24 pages