Vật Liệu Composite trên nền nhựa UPE và Thân Lục BìnhFull description
compositeFull description
Full description
Full description
This standard has been published in accordance with a decision taken by CEN/TC 249 to adopt, without alteration, International Standard ISO 527-5 as a European Standard.Full description
Research paper on Tensile structures. Illinois Institute of Technology.Full description
Research paper on Tensile structures. Illinois Institute of Technology.
tensile test
Tensile Test - Torsion test - MFull description
Full description
astm standar for plastics analysis
Tensile Testing Composite ASTM D3039 State-of-the-art tensile properties data generation for reinforced composites materials including tensile strength, tensile modulus and Poisson's ratio using align-pro, strain gages or extensometers performed at ambient, high or low temperatures with or without moisture conditioning. ASTM D3039 tensile testing is used to measure the force required to break a polymer composite specimen and the extent to which the specimen stretches or elongates e longates to that breaking point. Tensile tests produce a stress-strain diagram, which is used to determine tensile modulus. The data is often used to specify a material, to design parts to withstand application force and as a quality control check of materials. Since the physical properties of many materials c an vary depending on ambient temperature, it is sometimes appropriate to t est materials at temperatures that simulate the intended end use environment. Test procedure: Specimens are placed in the grips of a Universal Test Machine at a specified grip separation and pulled until failure. For ASTM D3039 the te st speed can be determined by t he material specification or time to failure (1 to 10 minutes). A typical test speed for standard test specimens is 2 mm/min (0.05 in/min). An extensometer or strain gauge is used to determine elongation and tensile modulus. Depending upon the reinforcement and type, testing in more than one orientation may be necessary. State-of-the-art equipment including Align-pro for reduced bending. Elevated or reduced temperature test procedure: A thermal chamber is installed on a Universal Test Machine. The chamber is designed to allow the te st mounts from the base and crosshead of the Universal Tester to pass through the top and bottom of the chamber. Standard test fixtures are installed inside the chamber, and testing is conducted inside the controlled thermal environment the same as it w ould be at ambient temperature. The chamber has internal electric heaters for elevated e levated temperatures and uses external carbo n dioxide gas or liquid nitrogen as a coolant for reduced temperatures. Specimen size: The most common specimen for ASTM D3039 is a constant rectangular cross section, 25 mm (1 in) wide and 250 mm (10 mm) long. Optional tabs can be bonded to the ends of the specimen to prevent gripping damage. Data: From tensile test results the following calculations can be made : 1. Tensile strength (MPa or PSI) 2. Tensile chord modulus of elasticity (MPA or PSI) 3. Tensile strain (%) 4. Poisson’s ratio 5. Transition Strain (%) Tensile Testing:
Tensile Testing of Polymers and Plastics Composite Materials Test Methods
Plastics Tensile Testing for ASTM D638 and ISO 527 Moisture Absorption of Matrix Composites ASTM D5229 Request more information to see how Intertek can help your organization with Tensile Testing Composite ASTM D3039.
Izod Impact (Notched) ASTM D256, ISO 180 Izod Impact Testing (Notched Izod) ASTM D256, ISO 180
Scope: Notched Izod Impact is a single point test that measures a materials resistance to impact from a swinging pendulum. Izod impact is defined as the kinetic energy needed to initiate fracture and continue the fracture until the specimen is broken. Izod specimens are notched to prevent deformation of the specimen upon impact. This test can be used as a quick and easy quality control check to determine if a material meets specific impact properties or to compare materials for general toughness. Test Procedure: The specimen is clamped into the pendulum impact test fixture with the notched side facing the striking edge of the pendulum. The pendulum is released and allowed to strike through the specimen. If breakage does not occur, a heavier hammer is used until failure occurs. Since many materials (especially thermoplastics) exhibit lower impact strength at reduced temperatures, it is sometimes appropriate to test materials at temperatures that simulate the intended end use environment. Reduced Temperature Test procedure: The specimens are conditioned at the specified temperature in a freezer until they reach equilibrium. The specimens are quickly removed, on e at a time, from the freezer and impacted. Neither ASTM n or ISO specify a conditioning time or elapsed time from freezer to impact typical values from other specifications are 6 hours of conditioning and 5 seconds from freezer to impact. Specimen size: The standard specimen for ASTM is 64 x 12.7 x 3.2 mm (2½ x ½ x 1/8 inch). The most common specimen thickness is 3.2 mm (0.125 inch), but the preferred thickness is 6.4 mm (0.25 inch) because it is not as likely to bend or crush. The depth under the notch of the specimen is 10.2 mm (0.4 inches).
The standard specimen for ISO is a Type 1A multipurpose specimen with the end tabs cut off. The resulting test sample measures 80 x 10 x 4 mm. The depth under the notch of the specimen is 8mm. Data: ASTM impact energy is expressed in J/m or ft-lb/in. Impact strength is calculated by dividing impact energy in J (or ft-lb) by the thickness of the specimen. The test result is typically the average of 5 specimens.
ISO impact strength is expressed in kJ/m2. Impact strength is calculated b y dividing impact energy in J by the area under the notch. The test result is typically the average of 10 specimens. The higher the resulting numbers the tougher the material. **Please note that this test description is intentionally generic in nature and aimed at providing a descriptive summary to enhance test understanding. Standards can be obtained from appropriate standard authorities.