National Board Number:
----
Mfr. Representative:
Date: 06.04.2015
Authorized Inspector:
Date: 06.04.2015
FORM U-1A MANUFACTURER'S DATA DATA REPORT FOR PRESSURE VESSELS (Alternative Form for Single Chamber, Completely Shop or Field Fabricated Vessels Only) As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1 Manufactured and certified by
1.
Shree Satyanarayan Industrial Suppliers Pvt Ltd
Plot No. B 78/1, Addl. Ambernath MIDC Anand Nagar, Ambernath (East) Thane, Maharashtra 421506 India (Name and address of Manufacturer)
Manufactured for
2.
LARSEN & TOUBRO LIMITED, CHENNAI (Name and address of Purchaser)
Location of installation
3.
Unknown (Name and address)
4.
5.
Vertical, Air Receiver
Type
SS/14/U/004/08
None SSIS/14/004/06 Rev.4 Sheet 01 Of 05 to 05 Of 05
(Manufacturer’s s serial number) (Horizontal or vertical, tank) (Manufacturer’
ASME Code, Section VIII, Div. 1
(CRN)
None
2013 [Edition and Addenda, if applicable (date)]
6.
(Nominal thickness)
(Material spec. number, grade)
2015 (Yearr built) (Yea
None [Special service per UG-120(d)]
(Code Case number)
1.5
1950
(Corr. allow.)
(Inner diameter)
14
SA 516 516 Grade 70
Shell
---(National Board number)
(Drawing number)
4500 [Length (overall)]
Body Flanges on Shells
Bolting No.
Type
ID
OD
--
--
--
--
7.
8.
Flange Thk Min Hub Thk --
Material
How Attached
Location
Num & Size
Bolting Material
Washer (OD, ID, thk)
Washer Material
--
--
--
--
--
--
--
--
Type 1 (welded, dbl.)
Spot
0.85
[Long. (Welded, dbl, sngl, lap, butt)]
[R.T. [R. T. (spot or full) ]
(Eff., %)
Seams
Heads: (a) Material
--(H.T. temp.)
SA 516 Grade 70
---
Type 1 (welded, dbl.)
(Time,hr.)
[Girth (welded, dbl, sngl, lap, butt)]
0.85
Spot
2
(Eff., %) (No. of courses)
[R.T. (spot or full)]
SA 516 Grade 70
(b) Material
(Spec., no., grade)
(Spec. no., grade)
Location (Top, Bottom, Ends)
Minimum Thickness
Corrosion Allowance
Crown Radius
(a)
Top
11.5
1.5
--
--
2:1
--
--
---
Concave
(b)
Bottom
11.5
1.5
--
--
2:1
--
--
--
Concave
Knuckle Radius
Elliptical Ratio
Conical Apex Angle
Hemispherical Radius
Side to Pressure (Convex or Concave)
Flat Diameter
Body Flanges on Heads
Bolting
(a) (b)
9.
Location
Type
ID
OD
---
---
---
---
MAWP
Flange Thk Min Hub Thk
---
---
---
N/A
(Internal)
5˚ C
N/A
At
Num & Size
Bolting Material
Washer (OD, ID, thk)
Washer Material
---
---
---
--65˚ C
at max. Temp.
(External)
Min. design metal temp
10.
How Attached
---
1.304 MPa (g)
Proof test
Material
N/A
(Internal)
(External)
2 Hydro, pneu. Or comb. comb . Test pressure 18 Kg/cm (g) [1.769 MPa (g)] .
1.304 MPa (g)
.
Nozzles, inspection, and safety valve openings:
Purpose (Inlet, Outlet, Drain, etc.)
Material
Diameter or Size Type
No.
Nozzle
Nozzle Thickness Flange
Nom.
Corr.
Reinforcement Material
Attachment Details Nozzle
Flange
Location (Insp. Open.)
See attached Form U-4 11.
Supports: Skirt
Yes (Yes or no)
12.
Lugs
(Number)
Legs
-
Other
--
(Number)
Attached
(Describe)
On bottom head & welded (Where and how)
Remarks: Manufacturer’s Partial Data Reports properly identified and signed by Commissioned Inspectors have been furnished for the following items of the report:-
None (Name of part, item number, Manufacturer’ Manufacturer’s s name and identifying stamp)
Remarks: 1) All dimensions are in mm, unless otherwise stated. 2) Safety valve shall be provided by the owner/designated agent. 3) Impact test exempted as per UG-20(f), UCS-66(a). 4) Hydrostatic test position is Horizontal. 5) PWHT Exempted (As per UW-2, UCS-56, and UCS.79). 6) N/A – Not Applicable 7) Manhole M1 are bolted with with cover SA-105, Class 150 B 16.5, Stud SA-193 Gr.B7,Nut Gr.B7,Nut SA-194 Gr. 2H,Size -1+1/4 -1+1/4 ” 8UN x175 LG,QTY-20 no’s. 8) Nozzle N18 are bolted with with cover SA-105, Class 150 B 16.5, Stud SA-193 Gr.B7,Nut Gr.B7,Nut SA-194 Gr. 2H Size - 1/2” UNC x 65 LG,QTY 4 no’s 9) RT Marking –RT4, Extent of radiography –(Shell-Spot, Efficiency-0.85),[Dish-Seamless, Efficiency-0.85),[Dish-Seamless, spot as per UW-11(a)(5)(b),Efficiency-1], UW-11(a)(5)(b),Efficiency-1], (Manhole M1-Long & Cir seam-Full,Efficiency-1).
National Board Number:
----
Mfr. Representative:
Date: 06.04.2015
Authorized Inspector:
Date: 06.04.2015
National Board Number:
----
Mfr. Representative:
Date: 06.04.2015
Authorized Inspector:
Date: 06.04.2015
FORM U-1A (Back)
CERTIFICATE OF SHOP/FIELD COMPLIANCE We certify that the statements made in this report are correct and that all details of design, material, construction, and workmanship of this vessel conform to the ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1.
“U”
Certificate of Authorization Number 42374
expires March 5, 2018
Date
06.04.2015
Co. name
Shree Satyanarayan Industrial Suppliers Pvt Ltd
Signed
(Manufacturer)
(Representative)
CERTIFICATE OF SHOP/FIELD INSPECTION Vessel constructed by Shree Satyanarayan Industrial Suppliers Pvt Ltd at Plot No. B 78/1, Addl. Ambernath MIDC Anand Nagar, Ambernath
(East) Thane, Maharashtra 421506 India . I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and employed by TUV NORD Systems GmbH Co. & KG Have inspected the component described in this Manufacturer's Data Report on 06.04.2015 , and state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1. By signing this cer tificate neither the Inspector nor his/her employ er makes any warranty, expressed or implied, concerning the pressure vessel desc ribed in this Manufacturer's Data Report. Furthermore, neither the Inspector nor his/her employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.
Date
06.04.2015 Signed
Commissions (Authorized Inspector)
NB#13486 ‘A’ ‘N’ ‘IS’ [National Board (incl. endorsements)]
