=
MAIN LEVEL ? ..... DISPLAY MENU A ..... ALARM SYSTEM ADMINISTRATION C ..... ROUTING STATE ADMINISTRATION D ..... SYSTEM SUPPORT AND COMMUNICATION E ..... CELLULAR RADIO NETWORK ADMINISTRATION F ..... FRAME RELAY ADMINISTRATION I ..... I/O SYSTEM ADMINISTRATION N ..... SS7 NETWORK ADMINISTRATION O ..... SUPPLEMENTARY SS7 NETWORK ADMINISTRATION Q ..... O&M NETWORK ADMINISTRATION R ..... ROUTING ADMINISTRATION T ..... TRAFFIC ADMINISTRATION U ..... UNIT ADMINISTRATION W ..... SYSTEM CONFIGURATION ADMINISTRATION Y ..... SYSTEM SUPERVISION Z; .... END DIALOGUE/DESTINATION SELECTION (:)
1. ZEEI:BCF=
; TELL ABOUT NO. OF CALLS IN EACH SECTOR. 2. ZEEL:BL; GIVE INFORMATION ABOUT BLOCK TRX IN EACH SECTOR. 3. ZEOL:; GIVE INFORMATION ABOUT PRSENT ALARMS. 4. ZERS:BTS=,TRX=:L OR U:; TO LOCK OR UNLOCK TRX. 5. ZEOH:YYYY-MM-DD:HH-MM-SS:BCF=; THIS COMMANDS TELLS ABOUT THE HISTORY OF ALARMS. 6. ZAHO:ET:; TO CHECK ALARMS ON ETS. 7. ZYMO:ET=; TO CHECKET LINK STATUS HAVE AN ERROR OR NOT. 8. ZDTI:::PCM=; TO INTERROGRATE ABOUT LAPD SIGNALS ON PARTICULAR ET. 9. ZUSI:TCSM; TO CHECK ALARMS ON TRANSCODERS. 10. ZACC TO DELETE PARTICULAR ALARM ON ET. 11. ZAHO; TO CHAEK ALARMS ON BSC. 12. ZEQS:BTS=:L or U; TO LOCK OR UNLOCK BTS. 13. ZEFS:BCF=L OR U;
TO LOCK OR UNLOCK BCF.
14. ZUSI:ET; TO CHECK ET STATUS WEATHER IT IS BLOCKING OR WORKING . 15. ZUSU:ET=;-TO CHANGE THE STATE OF ET TO BL,WO,SE. 16. ZERO:BCF=; TO SEE ALL THE PARAMETERS OF BCF. 17. ZFWO:BCSU=0&&6:BTS:; TO CHECK ALL THE GB LINKS IN THE PARTICULAR BSC. 18. ZESI:; TI CHECK EDAP GPRS MAPPING . 19. ZDSB:::PCM=; TO CHECK ALL THE PARAMETERS OF LAPD. 20. ZWIP:GSW:; TO CHECK THE ET ,IS IN WHICH INTERFACE. 21. ZYEF:ET=; TO CHECK WEATHER THE LOOP ON ET IS GETTING OR NOT. 22. ZUSU:ET=; FOR RESETTING ET PORT
23. ZYEC:ET=:NORM,CRC4,OFF; TO CHANGE ET MODE TO CRC4 OR DBLF. 24. ZFWO:BCSU=0&&6:BTS;TO CHECK GB LINKS IN THE PARTICULAR BSC. 25. ZESI; TO CHECK EDAP GPRS MAPPING. 26. ZDSB:::PCM=; TO CHECK ALL THE PARAMETERS OF LAPDS. 27
ZWIP:GSW:; TO CHECK THE ET ,IS IN WHICH INTERFACE.
28. ZYEI:ET=; TO INTERROGRATE ABOUT THE ET MODE. 30. ZEFR:SITE OR OMU; TO GIVE RESET TO WHOLE SITE
OR OMU OF
THE SITE . 31. ZRCI:SEA=3:CGR=1:PRINT=5; TO CHECK THE STATUS OF CKT. OF TRANSCODERS AND ALSO TO SEE THE KICK NO. 32. ZNEL; TO CHECK THE STATUS OF SIGNALLING. 33. ZDRA : BSC CLOCK CHECK. 34. ZQNI : C-NUMBER. 35. ZQVC : OMC00000OPAD,BSC(C-NUMBER)PAD:; - TO REMOTE OTHER BSC 36. ZABO : OUTPUT BLOCKED ALARM. 37. ZUCI : COMP; CHECK BSC COMP UNIT. 38.ZUSS : BSC RESTART COMMAND 39.ZDTI:::SAPI=62; CHECK ALL ET – NUMBERS 40.ZEFO:BCF NO:IOP:; - TO CHECK POLORITY OF ALARM 41.ZEFX:BCF NO:INBR=ALARM NUM:POL=OPEN OR CLOSED; TO CHANGE POLARITY OF ALARM. 42.ZDTF:TCSM;TO CHECK ALL THE TCSM 43.ZWQO:CR; TO CHECK THE SOFTWARE PACKAGE 44.ZWUC:
TO CREATE ET (ZWUC:ET,512:ET16,0:IF=A :BCSU,0;)
45. ZYMO:ET,512; TO CHECK ET HISTTROY ALARMS 46. ZISI; I/O DEVICE WORKING STATE AND SPARE DEVICE 47. ZTPM: MEASUR, TRAFFIC:ALL,0-00-23-00,60:; 48. ZEGO;NETWORK HANDLING COMMAND 49.ZDSE:TO CREATE TRX SIGNAL 50.ZERC:TO CREATE TRX 51.ZEQO : TO CHECK FREQEUNCY 52.ZDTC:TO UNLOCK TRX SIGNAL. 53.ZEAP : HANDOVER CHECKING 54.ZEQO : TO CHECK GENA AND EGENA 55.ZEQV : TO CHECK GENA AND EGENA STATUS 56.ZDTF:TO CHECK TCSM 57.ZDSD – TO DELETE TRX SIGNAL 58-ZERD-TO DELETE TRX 59- ZQUE:BCF=274,TRE=2:1:”4,20,0”;- to see the serial no. of FIFA