They are so important in our lives that without them even the electric bells fitted in our homes won’t work.
Certificate This is to certify that
, student of Class XII, KENDRIYA VIDYALAYA,
GOMTI NAGAR, LUCKNOW, has completed the project titled
Transformers during
“
”
the academic year 2013-2014, and submitted satisfactory report, as compiled in the following pages, under my supervision.
_________________ Department of Physics Kendriya Vidalaya, Gomti Nagar, Lucknow
Acknowledgements
"There are times when silence speaks so much more loudly than words of praise to only as good as belittle a person, whose words do not express, but only put a veneer over true feelings, which are of gratitude at this point of time." I would like to express my sincere gratitude to my physics mentor for h is vital support, guidance and encouragement, without which this project would not have come forth. I would also like to express my gratitude to the staff of the Department of Physics at Kendriya Vidyalaya for their support during the making of this project.
________________
INTRODUCTION___________
The transformer is a device used for converting a low alternating voltage to a high alternating voltage or a high alternating voltage into a low alternating voltage. It is a static electrical device that transfers energy by inductive coupling between its winding circuits. Transformers range in size from a thumbnail-sized coupling transformer hidden inside a stage microphone to huge units weighing hundreds of tons used in power plant substations or to interconnect portions of the power grid. All operate on the same basic principles, although the range of designs is wide. While new technologies have eliminated the need for transformers in some electronic circuits, transformers are still found in many electronic devices. Transformers are essential for highvoltage electric power transmission, which makes long-distance transmission economically practical. A transformer is most widely used device in both low and high current circuit. In a transformer, the electrical energy transfer from one circuit to another circuit takes place without the use of moving parts. A transformer which increases the voltages is called a step-up transformer. A transformer which decreases the A.C. voltages is called a step-down transformer. Transformer is, therefore, an essential piece of apparatus both for high and low current circuits.
Close-up of single-phase pole mount transformer.
PRINCIPLE___________
It is based on the principle of mutual induction that is if a varying current is set-up in a circuit then induced e.m.f. is produced in the neighboring circuit. The varying current in a circuit produce varying magnetic flux which induces e.m.f. in the neighboring circuit.
_ CONSTRUCTION___________
A transformer consists of a rectangular shaft iron core made of laminated sheets, well insulated from one another. Two coils p1 & p2 and s1 & s2 are wound on the same core, but are well insulated with each other. Note that the both the coils are insulated from the core, the source of alternating e.m.f is connected to p1p2, the primary coil and a load resistance R is connected to s1 s2, the secondary coil through an open switch S. thus there can be no current through the sec. coil so long
as
the
switch
is
open.
For
an
ideal
transformer, we assume that the resistance of the primary & secondary winding is negligible. Further, the energy loses due to magnetic the iron core is also negligible. For operation at low frequency, we may have a soft iron. The soft iron core is insulating by joining thin iron strips coated with varnish to insulate them to reduce energy losses by eddy currents. The input circuit is called primary. And the output circuit is called secondary.
An ideal voltage step-down transformer. The secondary current arises from the action of the secondary EMF on the (not shown) load impedance
__________________________________________________________________
The ideal transformer as a circuit element
_______THEORY_AND_WORKING____ When an altering e.m.f. is supplied to the primary coil p1p2, an alternating current starts falling in it. The altering current in the primary produces a changing magnetic flux, which induces altering voltage in the primary as well as in the secondary. In a good-transformer, whole of the magnetic flux linked
with
primary
is
also
linked
with
the
secondary, and then the induced e.m.f. induced in each turn of the secondary is equal to that induced in each turn of the primary. Thus if E p and Es be the instantaneous values of the e.m.f.’s induced in the primary and the secondary and N p and Ns are the no. of turns of the primary secondary coils of the transformer and, Dфь / dt = rate of change of flux in each turn of the coil at this instant, we have Ep = -Np Dфь /dt
(1)
Es = -Ns Dфь /dt
(2)
Since the above relations are true at every instant, so by dividing 2 by 1, we get Es / Ep = - Ns / Np
(3)
As Ep is the instantaneous value of back e.m.f induced
in
the
primary
coil
p 1,
so
the
instantaneous current in primary coil is due to the
difference (E – Ep ) in the instantaneous values of the applied and back e.m.f. further if R p is the resistance o, p1p2 coil, then the
instantaneous
current Ip in the primary coil is given by I =E – Ep / Rp E – Ep
=
Ip Rp
When the resistance of the primary is small, R p Ip can be neglected so therefore E – Ep
= 0 or Ep = E
Thus back e.m.f = input e.m.f Hence equation 3 can be written as E s / Ep = Es / E = output e.m.f / input e.m.f = N s / Np = K
Where K is constant, called turn or transformation ratio. In a step up transformer
Es > E so K > 1, hence N s > Np In a step down transformer
Es < E so K < 1, hence N s < Np If Ip=value of primary current at the same instant t And Is =value of sec. current at this instant, then Input power at the instant t = Ep Ip and Output power at the same instant
=
Es Is
If there are no losses of power in the transformer, then Input power = output power or Ep Ip
=
Es Is
Or
Es / Ep
=
Ip / Is
=
K
In a step up transformer
As k > 1, so I p > Is or Is < Ip I.e. current in sec. is weaker when secondary voltage is higher. Hence, whatever we gain in voltage, we lose in current in the same ratio. Similarly it can be shown, that in a step down transformer, whatever we lose in voltage, we gain in current in the same ratio.Thus a step up transformer in reality steps down the current & a step down transformer steps up the current.
BASIC IDEA OF STEP DOWN TRANSFORMER
_______________________________________________________
BASIC IDEA OF STEP UP TRANSFORMER
EFFICIENCY_____________ Efficiency of a transformer is defined as the ratio of output power to the input power i.e. η = output power / input power = E s Is / Ep Ip Thus in an ideal transformer, where there is no power losses, η = 1. But in actual practice, there are many power losses; therefore the efficiency of transformer is less than one.
ENERGY LOSSES____________ In practice, the output energy of a transformer is always less than the input energy, because energy losses occur due to a number of reasons as explained below.
1. Loss of Magnetic Flux : The coupling between the coils is seldom perfect. So, whole of the magnetic flux produced by the primary coil is not linked up with the secondary coil.
2. Iron Loss: In actual iron cores in spite of lamination,
Eddy currents are produced. The magnitude of eddy current may, however be small. And a part of energy is lost as the heat produced in the iron core.
3. Copper Loss: In practice, the coils of the transformer possess resistance. So a part of the energy is lost due to the heat produced in the resistance of the coil.
4. Hysteresis Loss: The alternating current in the coil tapes the iron core through complete cycle of magnetization. So Energy is lost due to hysteresis.
5. Magneto restriction : The alternating current in the Transformer may be set its parts in to vibrations and sound may be produced. It is called humming. Thus, a part of energy may be lost due to humming.
____ _ USES OF TRANSFORMER_____ A transformer is used in almost all a.c. operations
In voltage regulator for T.V., refrigerator, computer, air conditioner etc.
In the induction furnaces.
A step down transformer is used for welding purposes.
A step down transformer is used for obtaining large current.
A
step
up
transformer
is
used
for
the
production of X-Rays and NEON advertisement.
Transformers are used in voltage regulators and stabilized power supplies.
Transformers are used in the transmissions of a.c. over long distances.
Small transformers are used in Radio sets, telephones, loud speakers and electric bells etc.
__________________A BIG TRANSFORMER_______________
Bibliography The data used in this project was taken from the following sources: www.google.com www.wikipedia.com N.C.E.RT physics
